SPECIAL REPAIRS TO BLDG NO P 109 LRW OFFICE P 184 MD ACCN AND PROVN OF FALSE CEILING IN BLDG NO T 116 AT MIL STN DHRANGADHRA

Amount

Taking down old cement plaster any description on brick or stone wall/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc complete as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and directed

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) exc 1.5 Sqm but n.exc 4 Sqm each complete all as specified and directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) n.exc 1.5 Sqm each complete all as specified and directed.

Taking down of shutter of any description exc 1 sqm and n exc 2 sqm each complete all as specified and directed.

Taking down and refixing of shutters in same opening after easing and adjusting of any description exc 1 Sqm but not exc 2.0 Sqm each complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in CM including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M & L for walling of random rubble, uncoursed well bounded, bedded and solidly hearted, built in Cement Mortar 1:6 complete all as specified and directed.

M & L for walling (Except stone) of random rubble, uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:6 complete all as specified and directed

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface n exc 20mm for sand stone and dressing to face stones and dressing of face beds and joints as specified ,of random rubble walling ,uncoursed or brought upto courses completed as specified and directed .

S&F 6 mm thick of size 605x605mm HSPC (high pressure steam cured) per-primetered self embossed,textured designer board E-Board classic to be fixed anodised aluminium snap grid /section size 605mmx605mm with main runner ,cross tee and wall angle duly suspended with 4mm dia GI bar hangers 1200 mm center to center both ways purlin from the roof with alignment clip including providing provisions for light fixtures of any size complete all as specified .

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) complete all as specified and as directed.

Dismantling timber scantling 40 sqcm and over in section ,an any position (framed) complete all as specified and as directed.

M&L for dismantling for timber scantling fillet rails, post rafter purlin etc under 20 sqcm in section (unframed) complete all as specified and directed.

Taking down roof trusses ,coupled rafters or trussed besms above 4 mtr and upto 8 mtr complete all as specified and as directed.

Taking up or down steel tubing 15 mm bore and connection including cleaning for refixing complete all as specified and directed.

Taking up or down steel tubing 20 mm bore and connection including cleaning for refixing complete all as specified and directed.

Providing cement concrete 25 mm thick type B-1 (1:2:4) using 20 mm graded agg as in sub base to flooring complete all as specified and as directed.

M&L for Pre polished machine cut kota stone slab in flooring18-20 mm thick and including 20mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and finshed polishing in complete all as specified.

M&L for machine cut kota stone slab in flooring18-20 mm thick and including 15mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and finshed polishing in complete all as specified.

M&L for Pre polished machine cut kota stone slab, 18-20 mm thick in riser and tread single piece on steps, skirting, dado and pillar laid over and including 10mm thick rendering in CM 1:4 including grinding and finshed polishing complete all as specified and directed.

S&F in repair 20 mm thick factory made solid PVC flush Kitchen CB shutter /shutter ,uPVC ,made from co-extruded three layer rigid foam sheet (single extruded process ) with 0.8 to 1mm thick outer face layer having density not less than 1400 kg /cum and density of central core material not less 600 kg/cum , manufactured by an ISO 9001:2015 certified company and fixing in frame at site with and including 02 nos Cabinet hings frameless full overlay adjustable, 01 Nos S S fancy handle ,01 Nos S S tower bolt, Ball catches with 8mm dai steel ball and brass body and striding plate including letting for each shutter etc for Cup Board / Kitchen cabinets as per specification & drawing complete all as specified and directed Engr-in-charge.

M & L for rubbing and polishing to existing old kota stone slab/marble/terrazzo flooring and skirting to achieve required finish complete all as specified and directed.

M & L, non skid White ceramic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 Sqm, over and including 15 mm thick screed bed in CM 1:6 as in floor etc set & jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed

M & L, glazed coloured ceramic tiles in vertical surface as in skirting & dado, 7 to 8 mm thick area exc 0.05 Sqm but n.exc 0.18 Sqm over and including 10 mm thick rendering in CM1:4 set & jointed in neat cement slurry & pointed in coloured cement to match complete all as specified and directed.

M & L, non skid ceramic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm, over and including 15 mm thick screed bed in CM 1:6 as in floor etc set & jointed in neat cement slurry and pointed in cement to match complete all as specified and directed

M&L for 10 mm thick cement plaster on fair faces of brick work or concrete surfaces on wall in CM 1:4 complete all as specified and directed.

M&L for 10 mm thick cement plaster on fair faces of brick work or concrete surfaces on wall in CM 1:6 and finishing even and smooth without using extra cement complete all as specified and directed.

M&L for 10 mm thick cement plaster on fair faces of brick work or concrete surfaces on wall in CM 1:6 finished the plaster surfaces complete all as specified and directed.

M&L for 10 mm thick rendering in CM 1:4 on ceiling, soffits, chajja projection etc complete all as specified and directed.

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces on wall in CM 1:6 finished the plaster surfaces fair and even complete all as specified and directed.

M&L for 5 mm thick rendering in CM 1:4 on ceiling, soffits, chajja projection etc complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of concrete surfaces of roof as water proofing treatment in CM 1:4, including finishing the surfaces even and smooth, complete all as specified and directed.

Material and Labour for rendering 15 mm thick in two layers consisting of first layer 10mm in CM 1:6 and top layer 05 mm thick in CM (1:4) plastering with water proofing compund (@ 3% by weight of cement) on fair faces of brick work or concrete surface and finishing the surface even and smooth without using extra cement all as specified and directed. (Note:- Water proofing compund shall be measured and paid seprately.)

Preparation of new plastered surfaces and applying two coat of oil bound distemper over and including a layer of wall care putty complete all as specified and directed.

Preparation of new plastered surfaces and applying two coat of oil bound distemper over and including a layer of wall care putty to achive a smooth finish surface (average thickness 1 mm) complete all as specified and directed.

Preparation of old plastered surfaces by complete removal of existing treatment and applying two coat of oil bound distemper over and including a layer of wall care putty (average thickness 1 mm) complete all as specified and directed.

Preparation of new plastered surfaces and applying two coat of oil bound distemper over and including a layer of wall care putty to achive a smooth finish surface (average thickness 1 mm) complete all as specified and directed.

Preparation of old plastered surfaces by complete removal of existing treatment and applying two coat of oil bound distemper over and including a layer of wall care putty (average thickness 1 mm) complete all as specified and directed.

Preparing of plastered or unplastered old decorated surfaces of walls by complete removal of existing treatment, moulds, moss and efflorescent salt and treating oil and greasy spots and applying three coat of white wash on walls including cornices etc complete all as specified and directed

Preparing of plastered or unplastered old decorated surfaces of walls by complete removal of existing treatment, moulds, moss and efflorescent salt and treating oil and greasy spots and applying three coat of white wash on walls including cornices etc complete all as specified and directed

Preparation of old plastered or unplastered old decorated surfaces of walls by complete removal of existing treatment, scrapping down smoke soot, moulds, mass and efflorescent salts and trading oil and greasy spots and applying Two coat of cement base paint over on walls including cornices etc complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying one coats of cement base paint complete all as specified and directed.

Preparation of New plastered surfaces of ceiling and applying Three coat of white wash on ceiling including cornices etc complete all as specified and directed.

Preparation of plastered or unplastered old decorated surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soots, treating oily/greasy spots, moss and efflorescence and applying two coat of white wash on ceiling including cornices etc complete all as specified and directed.

S&F 1.25 mm thick Pressed steel frame size 125 x 60 for doors with one or more rebates including necessary S&F suitable MS hinges ,lugs, lock strike plate, hold fast complete all as specified and directed.

S&F 1.25 mm thick Pressed steel frame size 105 x 60 for doors with one or more rebates including necessary S&F suitable MS hinges ,lugs, lock strike plate, hold fast complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using (12.5 mm graded agggregate stone ) for back filling of Pressed steel frame etc complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 using 20mm graded stone for embedding of hold fast ,filling etc complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using (12.5 mm graded agggregate stone ) for back filling of Pressed steel frame etc complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 using 20mm graded stone for embedding of hold fast ,filling etc complete all as specified and directed.

Supply only water proofing compound ,complete all as specified and as directed.

M & L for water proofing treatment to roofs surfaces including a coat of applied bituminous shalitex primer @ 0.30 lit per sqm evenly on roof surface and a coat of hot bitumen 85/25 @ 1.2 kg/sqm shall be applied on primed surface and laying of 3mm thick APP modified polymeric membrane (weight not less than 3 kg/sqm) unrolled and bonded completly to the substrate with side overlap of 75 mm and end overlap of 100 mm and then sealed/fused by flame or bitumen and a coat of hot blown bitumen grade 85/25 @ 1.2 kg/sqm shall be applied on top of APP modified polymeric membrane as per manufacturer instruction and finally it will be finished with a coat of aluminium paint @ 0.20 kg/sqm ,complete all as specified and as directed .

Granite (of any type of coloured) work (table rubbed and polished) 20mm thick in steps jambs,pillars, window cills, cooking plateform /partition and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick screed bed in CM 1:6 incl moulding, chamfering of edges complete.

S&F 35 mm thick Flush shutter ,solid core construction ,with block board core and plywood face panel comercial type on boath sides complete all as specified and as directed .

S&F in repair Stainless steel Door hinges medium weight, cold rolled 100 mm size all as specified and directed.

S&F Aluminium anodised barrel tower bolt of extruded section length of bolt in 200 mm size complete all as specified and directed.

S&F 300 mm long Aluminium alloy ,anodised sliding door bolt with hasp staple (bolt type ) and fixing clips of sheet ,cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed .

S&F MS 300 mm ordinery rat rail rod pattern spring including roller and roller plate complete all as specified and as directed .

S&F 150mm long floor door stopper of aluminum alloy body and tongue , anodized with hard drawn steel spring complete all as specified and directed

S&F galvanised mild steel wire cloth 0.56 mm nomonal dia of bar and 1.18 mm avrage width of aperture ,fixed with tined tacks or galvanised wire staples complete all as specified and as directed.

M&L cutting out cracks to V-section in existing roof slab or terrace, cleaning out, wetting, grouting, with cement sand slurry in 1:3 with mixing of WPC @ 2% by wt of cement.

M&L, preparing of new wooden surface exceeding 10 cm in width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L, preparing old previously treated surface of wood and wood based surfaces exceeding 10 cm in width or girth and applying one coat of synthetic enamel paint on old decorated wooden surfaces, complete all as specified and directed.

S&F Steel windows with side hung shutters including Box type hinges with steel handle, and steel tower bolt, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel Ventilator with top hung shutters including Box type hinges with steel handle, and steel tower bolt, complete with glazing bars, dovetailed or welded complete all as specified and directed.

Supply and Fixing sheet glass 4.8 mm thick ordinary quality and glazing with oil putty or rubber and aluminium beading in squares n. exc 0.5 sqm in each pane complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

Supply and Fixing Figured glass pin head type (Figured glass) sheet glass 4mm thick ordinary quality and glazing with oil putty or rubber and aluminium beading in squares n. exc 0.5 sqm in each pane complete all as specified and directed.

M&L, preparing of new steel surface exceeding 10 cm in width or girth and applying two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L, preparing of new steel surface exceeding 10 cm in width or girth and applying two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S&F 35mm thick 2nd class hardwood glazed and skeleton shutters open rebated and prepared to receive glass or gauge etc(without sash bar), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass , etc size of members of shutters as specified in SSR part I ,section 8 clause 8.24(a) fitted to chowkats complete all as specified and directed.

S&F, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fit-ted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube and fixing in opening as per specification complete all as specified and directed

S&F in aluminium, anodised barrel tower bolts 150mm long of extruded section and fixed complete all as specified and directed.

S&F, aluminium handles 150mm size, cast type, anodised complete all as specified and directed.

S&F Aluminium eyes pice glass for main Gate and shutter complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 as in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like including demolition of existing RCC work in any position complete all as specified and as directed.

Use and waste of form work to soffit of suspanded slab such as roof slab ,floor slab landing and similar work n exc 200mm thick (horizontally or sloping complete all as specified and as directed.

M&L for TMT bar 6 to 8 mm dia including cutting bending and binding with MS wire anealed dia not less than 0.9 mm conplete all as specified and as directed.

Dismantling Asbestos cement (Corrugated semicorrugated ,etc) sheets in roof coverings complete all as specified and as directed.

M & L, Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour (as approved by GE) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws in single length complete all as specified and directed.

M & L Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of an colour (as approved by GE) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed.

M&L for , false ceiling consisting of wall angles ,main T ,cross T all of size 25 mm X25mmX1.4mm thick power coated GI grid frame work jointed angle as directed and mild steel hooks not less than 4 mm dia with arrangement for adjusting heights of ceiling with and incl provision of 4 mm thick E boards sheet in panels of size 600mmX600mm with necessary off cuts and fixing arrangements for ceiling ,tube light fitting incl dismantling of existing false ceiling complete all as specified and as directed.

S&F rolled mild steel section as in main and cross beams hip and jack rafters , purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates conforming to Fe-410, Gde E-250A all as specified and directed.

S&F for mild steel for roof truses (framed) ,trussed purlins crane gantires ,rails and fasternings and heavy bracket framming (beam tee angle channel or flat sections )including distance pieces , clats etc and confir to Fe-410-w (GdeE-250) quality A including one shop coat of zinc chrome primer complete all as specified and directed.

S&F MS angle iron framed work as in doors or gate of angle or other section conforming to Fe 290 (Gde E-165) with gusset plates rails braces etc complete including hangin galso fastenin gand fxing complete as specified and directed .

S&F standard aluminium section powder coated any colour as approved for door frames / shutters, window, ventilator frames/shutters three track sliding/fixed /louvered and partitions etc including jointing cleat and rubber beading/linning, Pivot ,locking aragement and fixed in position with stainless steel screws all as specified and as directed.

S&F in repairs bib taps cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed for iron pipe or or brass ferrule for 15 mm bore of pipe complete all as specified and as directed.

S&F in repairs Stop valves /Angle cock/ concealed stop valves cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed for iron pipe or or brass ferrule for 15 mm bore of pipe complete all as specified and as directed.

S&F in repair 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repair vitreous china squatting pan, orrisa pattern, size 580mm x 440mm white, with integral foot rests (excluding flushing cistern & flush pipe) including making good to disturbed floor with PCC complete all as specified and directed.

S&F in repairs PVC low level 10 lit capacity valveless syphonic action type flushing cistern including 32mm dia PVC flush pipe fixed in repairs complete all as specified and directed

S&F Brass chromium plated Tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified and as directed.

Dismantling of water tank & n exc 500 ltr capacity in litres and removing to store complete all as specified and as directed.

Supply & Fix 500 litre capacity three layered rotational moulded polythylene water storage tanks (cylindrical vertical with closed top ) hoisted and fixed in position complete all as specified and directed.

S&F 15 mm bore tubes medium grade galvanised with all fittings and fixed to walls, ceilings or laid concealed in floors incl cutting chases where required complete all as specified and directed

S&F 20 mm bore tubes medium grade galvanised with all fittings and fixed to walls, ceilings or laid concealed in floors incl cutting chases where required complete all as specified and directed

Refixing old serviceable 15 mm GI tubing and connection in new or old position (concealed in Wall, ceiling & floor etc.) including necessary fittings & fixtures etc. complete all as specified and directed

S&F 15 mm bore tubes medium grade galvanised with all fittings and fixed to walls, ceilings or laid in floors incl cutting chases where required complete complete all as specified and directed.

Refixing old serviceable 20 mm GI tubing and connection in new or old position (concealed in Wall, ceiling floor etc.) including necessary fittings & fixtures etc. complete all as specified and directed.

S&F 20 mm bore tubes medium grade galvanised with all fittings and fixed to walls, ceilings or laid in floors incl cutting chases where required complete complete all as specified and directed

S&F in repair 20mm Gate valves with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and as directed.

M&L for taking down , chipping and removing the loose, spailt, damaged cement concrete, cement mortor surfaces of RCC Columns, beams, walls, chajjah etc and exposing the reinforced cement , wire brushing and cleaning the exposed steel reinforced bar, applying rust remover over the cleaned re-bar surface wash the re-bar with clean water for removing all rusts from the old re-bar surfaces, fixing new reinforcement for strengthen the members as required, applying two coats of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified bond coat on affected concrete surfaces and finally providing polymer modified cement and quartz sand mortor in CM 1:3 mix , 40mm thk in two coats, using polymer SBR Latex or equivalent as approved @ 5 Ltrs per 50 Kg bag of cement complete all as per manufacturer's Specifications/instructions and as directed. Note :- (New reinforcement or Welded wire fabric) will be measured and paid separately) Make : Dr. Fixit/Sunanda/chemestik/Fosrok

Taking/removing existing tar felt treatment of any description from RCC roof slab, terrace etc by means of MS scrapper patty or any other suitable tools and removing to a distance 500 mtr from the starting point and depositing as directed.

S&F Oval type Wash Hand Basin superior quality 550 x 400 mm size fitted and including suitable waste coupling with west pipe complete all as specified and directed.

S&F in repair white glazed earthen ware vitreous china wash hand basin of size 550x400 mm with and including CI brackets ,32mm bore bras CP waste coupling lintel /out let PVC flexible pipe 600mm size for 15mm with brass nut and washers etc complete.

Supply & Fix in repair 15 mm dia pillar tap (long nose)cast copper alloy with capstan head chromium plated fancy type, screwed down high pressure, with or without lettered "Hot or Cold" with long swan neck swivel type screwed for iron pipe and fixed complete all as specified and directed.

S & F Soap dish chromium plated approximate size 160x 160x90mm complete all as specified and directed.

S&F 5.5mm thick glass shelf of size 600mm long fancy type fixed and including Chromium plated grils, screws and wooden /plastic cleats complete all as specified and directed

S&F 5.5mm thick glass corner shelf assembly fancy type size 250mmx250mmfixed with and including chromium plates brass screws and wooden /plastic cleats complete all as specified and directed

S & F Aluminium Hat pegs of 6 pegs,solid body 125mm to 175 mm complete all as specified and as directed.

S&F 32mm bore bottle trap of of PTMT having minium water seal of 25mm ( minimum weight 32mm-260gms) complete all as specified and directed.

S & F Aluminium peg sets of 6 pegs complete complete all as specified and directed.

S & F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S & F Brass chromium plated shower rose 125mm size incl shower arm complete all as specified and directed.

Supply & Fix in repairs, 75mm bore PVC(SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches or in floors and fixed to wall with PVC holding clamps complete all as specified and directed.

Supply & Fix in repairs, 75mm bore PVC(SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches or in floors and fixed to wall with PVC holding with sutable Mild Steel angle clamps complete all as specified and directed.

S&F in repairs, 110mm bore PVC(SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 50mm PVC (SWR) pipes single socket in any length and including bends and sockets complete all as specified and directed

S&F kitchen plate rack of stainless steel of size 720mm x 600mm x 230mm made out of 1mm thick steel sheet complete all as specified and directed.

S&F PVC cabinet mirror size 350mm x 450mm fixed with steel screw with rowl plug complete all as specified and directed.

M&L for sunken floor treatment as described as under (i) to (vii):- (i) Demolition of cement concrete of any description and in any position not otherwise specifically Provided or in any type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. (ii) M&L to fill the sunken floor with PCC (1:5:10) type E-2 using Brick aggregarte over the treated surface complete as directed . (iii) M&L 40mm thick (Min) PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate with integral water proofing compound as per manufacture instruction instructions on bottom of sunken portion with proper slope towards spout . Vertical sides shall be plastered in CM (1:3) 15mm thick mixed with water proofing compound as per manufacturer instructions .Plaster shall be extended over PCC coving when the same is green i.e. PCC & Plastger be carried out at the same time complete all as specified and directed. (iv) After laying sewage /Plumbing pipes with fixtures in position 2 coats of OMIPLAS EP -101 epoxy compound shall be applied complete all as specified and directed. (v) Spouts of 25mm dia GI pipe light grade projecting 450 mm clear of face outer a wall with mosquito proof cap on inner face of pipe shall be provided to drain out seepage water including cutting holes and making good if needed as specified and directed . (vi) Test again of water tightness by pounding for 72 hours & rectify defects if any till total elimination of defects complete all as specified and directed .the sunken portion shall be tested for leakage /seepage /dampness by pounding with water for 72 hours .in case any defect is noteced the portion shall be grounted with cement slurry mixed with suitable chemical & tested again .The process of grouting and testing shall be repeated till leakage /seepage /dampness is eliminated as specified and directed .

S&F in repairs, 125/110mm bore PVC (SWR) 'P’ trap complete all as specified and directed.

S&F in repairs, 75mm bore dia PVC floor trap (SWR) plain with grating including jointing with solvent cement to waste pipe complete all as specified and directed.

S&F in repairs, 110mm bore PVC(SWR) bends any radius, complete all as specified and directed.

S & F PVC (SWR) junction single,(Single T) equal or unequal 75 mm dia

S&F PVC (SWR) junction single,(Single T) equal or unequal 100 mm dia

S&F PVC (SWR) 75 mm dia vent cowl complete all as specified and as directed.

S&F Sinks made of stainless steel 0.8 mm thick kitchen with plugs washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x420mm bowl size 410mm x 330mm x160mm ,including cupling , west pipe etc complete all as specified and directed.

M&L for 20 mm thick Granite (of any type of coloured) tiles maxhine cut in skirting/dado laid over cement screed and jointed with grey cement slurry ,and pointed with grey cement slurry ,and pointed with white cement with adimixture of pigment to match the shade of granite stone including grinding and polishing complete over 15mm thick screed bed in CM 1:6 incl moulding, chamfering of edges complete.

M&L for cement concrete 75mm thick type C-2 (1:3:6) using 40 mm graded agg as in sub base to flooring and including demolition of existing concrete work.

M&L for 50 mm thick PCC 1:3:6 type C-2 (using 40 mm graded Stone aggregate) as in plinth protection finisheed with out using extra cement complete.

M&L for 25mm thick cement concrete type B-0,1:2:4 (12.5 mm graded aggregate) for roof padding finishing cement concrete surface even and smooth with out using extra cement

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour,design & pattern as in footpath parks, lawns ,drive ways or light traffic parking etc ,of required strength , thickness & size /shape ,made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of coarse sand , compacting and proper embedding /laying of inter locking paver block into the sand bedding layer through vibratory compaction by using plate vibrator ,filling the joints with fine sand and cutting of paver block as per required size and pattern ,finishing and sweeping extra sand complete all as specified and as directed.M/S Mehtab Tiles, M/S NITCO(NITCO), M/S Ultra Tiles (ULTRA).

Demolition of precast concrete articles and pre-cast cement concrete block walling, ashlar fencings, dressed stone work including all quoins, arches, pillars etc. built in cement mortar complete all as specified and directed.

M & L, cement concrete 1:2:4 type B-2, using 40 mm graded stone aggregate as in surface channel or drain complete all as specified and directed.

M&L, precast cement concrete Block Masonary with solid blocks type C1, 1:3:6 (20mm graded stone aggregate) exc 10 cm in width and setting in mortar 1:6 complete all as specified and directed .

M&L, precast cement concrete Block Masonary with solid blocks type C1, 1:3:6 (20mm graded stone aggregate) exc 10 cm in width (except blocks) and setting in mortar 1:6 complete all as specified and directed .

M&L, providing cement concrete1:2:4 type B1 as in , coping ,benching, bressumers, steps, incl necessary form work and demolition of existing cement work complete all as specified and as directed.

M&L in repair for precast cement concrete 1:2:4 type B-1, (using 20mm graded stone aggregate) as in manhole covers , shelves, chajjas etc and similar articles with plain faces set in CM 1:4 complete.

Demolition of plain cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

S&F Harrison rails, mild steel chromium plated with fixing brackets ,stops ,rolleres etc complete all as specified and as directed.

S&F, in repair, 20mm dia, stainless steel, fancy type ,tubular curtain rod fixed on decorative brackets with decorative fancy type globe at both end complete all as specified and as directed.

S&F M.S Framed work such as grills gratings etc with ends of bars sholdered and/or riveted into spikes ,framed guard bars /railings all as directed .

Taking down carefully copper/aluminium point wiring (Light, fan, socket or power etc.) complete including fitting such as switches, socket, bell pushes, ceiling roses, pendants/batten holder, call bell, regulators etc all as specified and directed by Engr-in-charge.

M&L for point wiring for one light/fan/bell point controlled by one switch one way in & including PVC conduit concealed in brick or stone wall using FRLS PVC unsheathed multistrand copper conductor wire 1.5 sqmm single core for one light/fan point controlled by one switch including modular white cover plate with frame of suitable modules over modular metal flush box concealed type for earth continuity insulated PVC unsheathed (green colour) 1.5 sqmm copper earth wire connected to common earth dolly using complete all as specified and directed by Engr-in-charge. Note : (a) wiring shall be done by using proper colour coding.

All as per srl item No. 149 here-in-before but for 6 Amp socket outlet on independent board complete all as specified.

All as per srl item No. 149 here-in-before but for 6 Amp socket outlet on same board complete all as specified

All as per srl item No. 149 here-in-before but for one light point controlled by two switches of two way complete all as specified.

All as per srl item No. 149 here-in-before but for 6/16 Amp independent socket outlet using 2.5 sqmm single core wire (for phase, nuetral and earth) complete all as specified.

M&L for point wiring for one light/Fan point controlled by one switch one way in & including PVC casing and capping using FRLS PVC sheathed multistrand copper conductor wire 1.5 sqmm single core for one light/fan point controlled by one switch including 3 mm thick plastic laminated sheet cover over concealed MS sunken box for earth continuity insulated PVC unsheathed (green colour) 1.5 sqmm copper earth wire connected to common earth dolly using complete all as specified and directed by Engr-in-charge. Note : (a) wiring shall be done by using proper colour coding.

All as per srl item No. 154 here-in-before but for 05 Amp socket outlet on independent board complete all as specified.

All as per srl item No. 154 here-in-before but for 05 Amp socket outlet on same board complete all as specified.

All as per srl item No. 154 here-in-before but for 15 Amp independent socket outlet using 2.5 sqmm single core wire (for phase, nuetral and earth) complete all as specified.

S&F Switch piano, flush type 5 Amps One Way 230 volts complete all as specified.

S&F Switch one way 15 Amps flush type 230 volts complete all as specified.

S&F socket outlet 3 pin 6 Amps flush type 230 volts complete all as specified.

S&F modular switch one way 16 Amps flush type 230 volts complete all as specified.

S&F modular switch piano, flush type 6 Amps two way 230 volts complete all as specified.

S&F modular bell push 6 Amps, 1 module complete all as specified and directed.

S&F, in repairs, bell, A.C. 230 Volts, single pole, Ding doll, complete all as specified and directed.

S&F modular socket outlet 3 pin 6 & 16 Amps flush type 230 volts complete all as specified.

S&F Socket outlet 2-in-1 3 pin 6 & 16 Amps flush type 230 volts complete all as specified.

S&F ceiling rose 3 terminal size 50x65mm surface type 230 volts complete all as specified.

S&F modular switch piano, flush type 6 Amps one way 230 volts complete all as specified.

S&F modular socket 3 pin 6 Amps flush type 230 volts complete all as specified.

S&F, modular fan step type regulator, suitable for 1200mm/1400mm sweep ceiling fan, 2 module complete all as specified and directed.

S&F fan regulator stepped type, electronic, flush type on the existing phenolic laminated sheet etc. complete all as specified and directed by Engineer-in-Charge.

S&F Holder insulated body with back plate for batten fitting suitable for LED lamp complete all as specified and directed by Engineer-in-Charge.

Labour only for Cutting openings, through brick walls for fixing of exhaust fan, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core etc. and rubbish not exc. 50m. Forming jambs, etc. to openings for 230/300mm exhaust fan including cutting in wall fo cement mortar 1:6, toothing, and properly bonding into old work, also facing, jointing and pointing to match existing work, complete

Supply and fix of exhaust fan, 230 mm sweep, 1400 rpm, MS body heavy duty, AC single phase, 230 volts with, blades, and frame and louvers including connection with 0.5 sqmm multistranded copper conductor flexible wire from ceiling rose, necessary fixing arrangement i.e anchor nut, bolt, washer, grouting and making good to disturbed surface complete all as specified and as directed.

Supply and fix of exhaust fan, 300 mm sweep, 1400 rpm, MS body heavy duty, AC single phase, 230 volts with, blades, and frame and louvers including connection with 0.5 sqmm multistranded copper conductor flexible wire from ceiling rose, necessary fixing arrangement i.e anchor nut, bolt, washer, grouting and making good to disturbed surface complete all as specified and as directed.

S&F LED Adore Lamp 9W, B22 base 6500K CDL type complete all as directed by Engr-In-charge. Make: Havells or Equivalent

S&F LED compact fitting/batten for single LED tube of 1x20W, 220V, AC decorative box type 4ft with integral LED driver including 20W, T8 tube rod complete all as directed by Engr-In-charge.

S&F LED compact fitting/batten for single LED tube of 1x10W, 220V, AC decorative batten type 2ft complete all as directed by Engr-In-charge.

S&F LED flat panel of size 2' x 2', 36 Watts, environmental friendly, new generation, aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source, suitable for Armstrong/Grid ceiling complete all as specified and directed by Engr-in-charge.

Taking down carefully old unsv submain wiring of any type/any size with PVC conduit or casing caping complete all as specified and directed.

Taking down carefully old unserviceable main switches/ Distribution board any type including fuses MCB etc after removing all connection, wires and making good the disturb surface complete all as directed by Engineer-in-charge.

Taking out KWH electric meter single phase by disconnecting electrical connections from DB and kept in safe custody for refix in the same location complete all as directed by Engr-in-Charge.

S&F ceiling fans 1200mm sweep energy efficient five star rated 230 volts with brushless direct current motor (BLDC) with blades, down rods, electronic regulator control type including down rods and connecting up with 3 runs of suitable size single core PVC insulated but unsheathed, FRLS cable with multistanded copper conductors from ceiling rose to fan complete all as specified and as directed.

M&L for sub main wiring complete with FRLS PVC insulated unsheathed stranded copper conductor wire 4.0 Sq mm 02 runs (for Phase & Neutal) along with earth wire FRLS PVC insulated unsheathed stranded copper conductor wire of size 4.0 sq mm wire drawn through in & including PVC casing caping or conduit as per site requirement complete all as directed by Engr-In-charge.

Disconnecting carefully and taking down the existing ceiling fan of any size, and depositing to MES E/M store for safe custody complete all as directed by Engr-in-Charge

Supply and fix electric water heater, storage type steel body with stainless steel inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated, 230Volts, single phase, 50 Hz AC, energy saving high density PUF insulation complete with all accessories such as safety valve, thermostate, NRV, NRV, inlet and outlet (cold & hot) PVC pipes upto 450mm long, with 15A plug top etc. complete all as specified and directed.

S&F DB with metal plug and socket double pole with MCB SP of 20 Amps, 230 V, 10 KA all as specified and as directed by Engineer-in-charge.

S&F Sheet metal enclosure double door for DB's SPN 12 way 240 V having 200 A rated bus bar complete all as specified and directed by Engr-in-charge.

S&F Sheet metal enclosure double door for DB's SPN 8 way 240 V having 200 A rated bus bar complete all as specified and directed by Engr-in-charge.

S&F MCB SPN 32A, 240 V -10 KA all as specified and as directed by Engineer-in-charge.

S&F MCB SP 6-32A, 240 V -10 KA all as specified and as directed by Engineer-in-charge.

Supply, fixing, hanging & laying of Steel tubing medium grade galvanised of size 25mm dia laid in trench, hanging in roof or fixed to wall complete all as specified & directed.

S&F Wall mounting fan, oscillating type, single phase with speed regulator step type 400 mm sweep complete all as specified and as directed.

S&F Distribution Board VTPN, 4 way, 415 volts, factory made powder coated, double door with neutral and earth link, including 3 pole MCCB 63 Amps rating, 25KA breaking capacity for incoming supply and provision of MCB SP/TP for out going supply complete all as specified and directed.

S&F 30W New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 for bldg security light with GI pipe bracket of suitable size for fitting complete all as specified and directed by Engineer-in-charge.

Supply & laying sub class 'B' bricks for protection of cable and laid perpendicular to the trench all as specified & directed by Engineer-in-Charge.

Supply, install, testing and commissioning of factory made CPRI approved LT panel box wall mounted compartment type made out of CRCA sheet of 2 mm thick indoor type totally enclosed weather, dust and vermin proof with front opening hinged door and locking arrangement mounted on MS flat iron clamp welded to panel body duly grouted in wall, 415 volts 3 phase, 4 wire AC 50 HZ having 4 pole, aluminium bus bar of 200 Amps including provn of space for installation of existing single phase prepaid meter - 06 Nos, hold fast, fastener bolts, copper lugs, rubber, gasket locking knobs, nuts, bolts, washers etc suitable single core copper wire connections and epoxy powder spray paint with primer including complete all as specified including the following accessories:- (a) TP MCCB 63 Amp 415 Volts, 16KA breaking capacity -01 No (b) MCB SPN outgoing 40 Amp 10 KA- 07 Nos (c) Re-fixing of single phase electric energy meters obtained in item No 29 here-in-above (d) Copper cable 6 sqmm wire for internal connection and provide earth links on both sides. Note:- Quarter No. to be mentioned in respective meters compartment.

M&L for pipe Chemical earthing with GI pipe electrode 2.25m long having outer pipe nominal dia 80mm & inner dia 50mm dily filled with highly condictive and corrosive compound of required quantity having chemical Betonite 40%, Copper sulphate 20%, Gypsum 5%, Grafite 10%, Alum 5%, Zinc sulphate 10%, Aluminium sulphate 10% Buried in ground digging a bore of 150mm dia surrounded by soil friendly backfill compound non solube in water including connection with and including GI strip 32 x 6 mm upto 7.5m PCC pit with RCC cover etc complete. Note : Rate quoted by tenderers shall be deemed to include for following provisions:-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 M.[ii]. PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles. [iii]. GI protection pipe of size 40 mm bore light grade 7.5m and testing on completion complete all as specified and directed.

Excavation, in trenches not exceeding 1.5 mtr wide and not exc 1.5 mtr in depth for laying under ground cable in hard & dense soil and getting out complete all as specified & directed by Engr-in-Charge.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick all as specified & directed by Engineer-in-Charge.

Removal of surplus excavated material to a distance not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed by Engineer-in-Charge.

Sand cushioning to under ground cable with dry sand locally available 8cm thick before laying the cable and 15 cm above the cable, stretching and testing of cable complete all as specified & directed.

Supply and laying of Steel tubing light grade galvanised of size 40mm dia laid in trench for protection of cable complete all as specified & directed.

Supply, laying in trenches or passing through pipes and testing cable XLPE Insualted screened PVC bedded, galvanised steel strip armored, electric power cables (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 Sqmm 4 Core including taking down the existing cable of any size.

M&L for earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth Lead 4 mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part I connected to DB using earth wire of 4mm dia as earth lead all as specified and testing on completion including provision of earth lead protected by 20 mm dia light grade GI pipe & watering pipe shall be 15 mm bore medium grade GI pipe including all excavation and earth work in any type of soil, PCC pit with RCC cover, char coal, salt, funnel etc complete. Note : Rate quoted by tenderers shall be deemed to include for following provisions:-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 M.[ii]. PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles.[iii]. Main earthing lead from earth electrode to test point upto 7.5 mtr.[iv]. Funnel with watering pipe [GI pipe] 15 mm bore [ISI marked] medium grade & copper lugs, charcoal & salt as reqd.[v]. GI protection pipe of size 20 mm bore light grade 7.5m.

ALBA AC AND REF SERVICES (BID ID -3386499)

partechengineers (BID ID -3383509)

Bhumi Construction (BID ID -3386529)

Singh Engineer And Contractor (BID ID -3381420)

Abhishek Enterprises (BID ID -3390745)