Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | 1₹42.7 LAccepted-AOC DURGA NAGAR CHECKPOST PO ETHELBARI DIST ALIPURDUAR PIN 735204 | ALIPURDUAR | WEST BENGAL | 735204 | 1 | Accepted-AOC LOWEST BIDDER | |
| 2 | 2₹46.6 L+₹71,180 (1.55%)Rejected-AOC 65 JOY NARAYAN BABU ANANDA DUTTA LANE HOWRAH 711101 | HOWRAH | WEST BENGAL | 711101 | 2 | Rejected-AOC OTHER THEN LOWEST BIDDER | |
| 3 | 3₹46.7 L+₹74,868 (1.63%)Rejected-AOC | 3 | Rejected-AOC OTHER THEN LOWEST BIDDER | |
| 4 | 4₹47.5 L+₹1.5 L (3.37%)Rejected-AOC | 4 | Rejected-AOC OTHER THEN LOWEST BIDDER | |
| 5 | 5₹47.6 L+₹1.7 L (3.60%)Rejected-AOC | 5 | Rejected-AOC OTHER THEN LOWEST BIDDER |
| Sl No | Description | Qty | Unit | N K Construction L6 | M/S DELTA ENGINEERS & CO L5 | M/S S.K. CONSTRUCTION L7 | M/S ALOKE CHAKRABORTY and CO L1 | M/s. RAMPHAL GARG L4 | M/S Pradeep Enterprise L3 | M K Engineering WOrks L2 |
|---|---|---|---|---|---|---|---|---|---|---|
| 1.00 | Lifting of defective submersible pumping set/unserviceable cable of any make and capacity from bore well after providing lifting tools and tackles as required carefully, disconnecting all electric connections, water connection and dismantling column pipe lines shaft stage by stage and keep them under safe custody for reuse all complete and lowering the same after repairs / overhauling submersible pump/serviceable cable of any make and capacity inside bore wells after coupling with pump and motor connecting column pipe line shaft stage by stage carefully with help of lifting tools and tackles carefully re-connecting all electric/water lines and testing on load upto the satisfactions complete all as specified.
Notes:- The rates for lifting and lowering of repaired pumping set shall deemed to include the cost following :-
(i) Replacement of rusted/ unsv bolts, nuts and washers
(ii) Replacement of rubber packaging of flanged joints
(iii) Fixing of submersible cable of any size.
(iv) Fixing charges for any clamps etc. | 36 | Each Job | 15,000 ₹5,40,000 | 12,750 ₹4,59,000 | 12,500 ₹4,50,000 | 11,800 ₹4,24,800 Lowest | 13,500 ₹4,86,000 | 11,995 ₹4,31,820 | 11,990 ₹4,31,640 |
| 2.00 | M&L for rewinding of burnt submersible motor 31 to 50 HP, 3 phase, 415 Volts, 50 Hz of any Make with PVC insulated water proof copper conductor of the same specification as per old one after dismantling cutting out burnt winding from stator assembly, cleaning slots properly complete with insulating slots packing, sleeves, papers, reassembling stator and rotor after replacement of of worn out spares/matching works including painting with two coats of synthetic enamel paints over a coat of red oxide after preparation of motor external surface and water proof jointing for submersible cable 3 core all complete as specified.
Note : Supply of spare parts required for overhauling/servicing except winding wire and other as described on the item shall be measured and paid seperately. | 12 | Each Job | 28,950 ₹3,47,400 | 28,990 ₹3,47,880 | 30,500 ₹3,66,000 | 28,500 ₹3,42,000 Lowest | 29,000 ₹3,48,000 | 28,970 ₹3,47,640 | 28,960 ₹3,47,520 |
| 3.00 | Ditto all as per serial item No 2 described here-in-before but capacity of submersible motor 15 to 30 HP complete all as specified. | 8 | Each Job | 19,500 ₹1,56,000 Lowest | 19,530 ₹1,56,240 | 21,250 ₹1,70,000 | 19,500 ₹1,56,000 Lowest | 19,525 ₹1,56,200 | 19,520 ₹1,56,160 | 19,510 ₹1,56,080 |
| 4.00Supply only following spare parts of submersible motor of capacity 31 to 50 HP:- | ||||||||||
| 4.01 | Thrust bearing plate for carbon TB assy | 10 | Each | 2,500 ₹25,000 | 2,550 ₹25,500 | 2,500 ₹25,000 | 2,400 ₹24,000 Lowest | 2,500 ₹25,000 | 2,495 ₹24,950 | 2,490 ₹24,900 |
| 4.02 | Bearing bush rubber for motor shaft complete all as specified. | 10 | Each | 2,450 ₹24,500 Lowest | 2,490 ₹24,900 | 2,500 ₹25,000 | 2,450 ₹24,500 Lowest | 2,480 ₹24,800 | 2,475 ₹24,750 | 2,470 ₹24,700 |
| 4.03 | Motor shaft sleeves (Stainless steel) complete all as specified. | 10 | Each | 730 ₹7,300 | 740 ₹7,400 | 750 ₹7,500 | 700 ₹7,000 Lowest | 735 ₹7,350 | 730 ₹7,300 | 735 ₹7,350 |
| 4.04 | Thrust bearing assy carbon complete all as specified. | 12 | Each | 3,640 ₹43,680 | 3,660 ₹43,920 | 3,650 ₹43,800 | 3,600 ₹43,200 Lowest | 3,650 ₹43,800 | 3,640 ₹43,680 | 3,650 ₹43,800 |
| 4.05 | GM bush for motor shaft complete all as specified. | 12 | Each | 1,260 ₹15,120 | 1,290 ₹15,480 | 1,250 ₹15,000 | 1,200 ₹14,400 Lowest | 1,285 ₹15,420 | 1,280 ₹15,360 | 1,270 ₹15,240 |
| 4.06 | Motor Sand Guard complete all as specified. | 12 | Each | 550 ₹6,600 Lowest | 575 ₹6,900 | 560 ₹6,720 | 550 ₹6,600 Lowest | 570 ₹6,840 | 565 ₹6,780 | 560 ₹6,720 |
Tender Value
₹44 L
EMD Value
₹88,000
Closing Date
23 Oct 2025, 6:00 pmClosed
GE S BINNAGURI
GE S BINNAGURI PO_BINNAGURI DIST_JALPAIGURI PIN_735232
AS PER TENDER DOCUMENTS
2025_MES_725944_1
8810/E8
Open Tender
Civil Works - Water Works
Item Rate
270 days
GE S BINNAGURI
Class D and Category a(ii)
7 documents required · 7 mandatory
₹500
GE S BINNAGURI
₹88,000
Yes
9 Dec 2025
25 Sept 2025
30 Oct 2025
25 Sept 2025
23 Oct 2025
9 Oct 2025
25 Sept 2025 - 9 Oct 2025
Amount
Lifting of defective submersible pumping set/unserviceable cable of any make and capacity from bore well after providing lifting tools and tackles as required carefully, disconnecting all electric connections, water connection and dismantling column pipe lines shaft stage by stage and keep them under safe custody for reuse all complete and lowering the same after repairs / overhauling submersible pump/serviceable cable of any make and capacity inside bore wells after coupling with pump and motor connecting column pipe line shaft stage by stage carefully with help of lifting tools and tackles carefully re-connecting all electric/water lines and testing on load upto the satisfactions complete all as specified. Notes:- The rates for lifting and lowering of repaired pumping set shall deemed to include the cost following :- (i) Replacement of rusted/ unsv bolts, nuts and washers (ii) Replacement of rubber packaging of flanged joints (iii) Fixing of submersible cable of any size. (iv) Fixing charges for any clamps etc.
M&L for rewinding of burnt submersible motor 31 to 50 HP, 3 phase, 415 Volts, 50 Hz of any Make with PVC insulated water proof copper conductor of the same specification as per old one after dismantling cutting out burnt winding from stator assembly, cleaning slots properly complete with insulating slots packing, sleeves, papers, reassembling stator and rotor after replacement of of worn out spares/matching works including painting with two coats of synthetic enamel paints over a coat of red oxide after preparation of motor external surface and water proof jointing for submersible cable 3 core all complete as specified. Note : Supply of spare parts required for overhauling/servicing except winding wire and other as described on the item shall be measured and paid seperately.
Ditto all as per serial item No 2 described here-in-before but capacity of submersible motor 15 to 30 HP complete all as specified.
Supply only following spare parts of submersible motor of capacity 31 to 50 HP:-
Thrust bearing plate for carbon TB assy
Bearing bush rubber for motor shaft complete all as specified.
Motor shaft sleeves (Stainless steel) complete all as specified.
Thrust bearing assy carbon complete all as specified.
GM bush for motor shaft complete all as specified.
Motor Sand Guard complete all as specified.
Oil seal complete all as specified.
Motor bearing housing complete all as specified.
Copper end ring complete all as specified.
Motor coupling key complete all as specified.
Motor coupling complete all as specified.
Pad for thrust bearing made out of bronze complete all as specified.
Pad for thrust bearing made out of Carbon complete all as specified.
Stud nut stainless steel complete all as specified.
Sir clip complete all as specified.
Supply only following spare parts of submersible motor of capacity 15 to 30 HP:-
Thrust bearing plate for carbon TB assy
Bearing bush rubber for motor shaft complete all as specified.
Motor shaft sleeves (Stainless steel) complete all as specified.
Thrust bearing assy carbon complete all as specified.
GM bush for motor shaft complete all as specified.
Motor Sand Guard complete all as specified.
Oil seal complete all as specified.
Motor bearing housing complete all as specified.
Copper end ring complete all as specified.
Motor coupling key complete all as specified.
Motor coupling complete all as specified.
Pad for thrust bearing made out of bronze complete all as specified.
Pad for thrust bearing made out of Carbon complete all as specified.
Stud nut stainless steel complete all as specified.
Sir clip complete all as specified.
Remetaling, cutting, grinding & polishing of Rotor shaft of capacity 31 to 50 HP in the worn out portion including checking of electricity in the lathe machine complete all as specified.
Ditto all as per serial item No 6 described here-in-before but capacity of motor 15 HP to 30 HP complete all as specified.
Remetaling, cutting, grinding & polishing of Thrust bearing of capacity 31-50 HP housing lower and upper in workshop complete all as specified.
Ditto all as per serial item No 8 described here-in-before but capacity 15 HP to 30 HP complete all as specified.
Dismantling submersible pump any make of capacity 1500 LPM to 1750 LPM for overhauling/servicing cleaning thoroughly discharge/suction capes, impellers shaft and assembling pump carefuly after fixing of spare parts/machining works including applying two coats of synthetic enamel painting after preparation of surface complete including testing on load upto the entire satisfactioncomplete all as specified. (Note : Supply of spare parts required for overhauling/servicing in place of worn out parts shall be measured and paid separately).
Ditto all as per serial item No 10 described here-in-before but capacity of pump 600-1100LPM (15 to 30 HP) complete all as specified.
Supply only following parts of submersible Pump of capacity 1500 to 1750 LPM:-
Gun Metal bush for suction impeller complete all as specified.
Gun Metal bush for discharge impeller complete all as specified.
Shaft sleeves Stainless steel complete all as specified.
Mild Steel stud for bowl assembly complete all as specified.
Neck ring Gun Metal complete all as specified.
Gun Metal bush for stage casing complete all as specified.
Stainless steel Impeller complete all as specified.
Key for impeller complete all as specified.
Suction case strainer complete all as specified.
Pump shaft stainless steel complete all as specified.
Sand Guard complete all as specified.
Stage casing complete all as specified.
Coupling with key for pump and motor complete all as specified.
MS socket heavy duty 8/11 TPI complete all as specified.
Pump NRV CI complete all as specified.
Supply only following parts of submersible Pump of capacity 600-1100 LPM:-
Gun Metal bush for discharge impeller complete all as specified.
Gun Metal bush for discharge impeller complete all as specified.
Shaft sleeves Stainless steel complete all as specified.
Mild Steel stud for bowl assembly complete all as specified.
Neck ring Gun Metal complete all as specified.
Gun Metal bush for stage carrier complete all as specified.
Gun Metal Impeller complete all as specified.
Key for impeller complete all as specified.
Suction case strainer complete all as specified.
Pump shaft stainless steel complete all as specified.
Sand Guard complete all as specified.
Stage casing complete all as specified.
Coupling with key for pump and motor complete all as specified.
MS socket heavy duty 8/11 TPI complete all as specified.
Pump NRV CI complete all as specified.
Remetaling, cutting,grinding, polishing for worn out portion of submersible pump shaft (Pump capacity 1500 to 1750 LPM) including fixing new Mild Steel key of suitable size and checking of balanced and properly aligned shaft at lathe Machine all complete as specified.
Ditto all as per serial item No 14 described here-in-before but for Pump capacity 600 LPM to 1100 LPM) complete all as specified.
Cutting of worn out threaded portion of column pipe 150 mm dia and threading the same in lathe Machine to existing TPI complete all as specified.
Ditto all as per serial item No 16 described here-in-before but 100 mm dia complete all as specified.
S&F Mild Steel Column pipe heavy duty (ERW) both end threaded with one socket /flange of wall thickness 5.04mm & length 3.00 mtr. 150mm bore conforming to IS-1239 (Part-I) 1979, and properly painted with one coat of black bituminous of surface internally and externally suitable for the drinking water including taking out of old unserviceable column pipe from position complete all as specified
Ditto all as per serial item No 18 described here-in-before but 100 mm dia complete all as specified..
Supply & fixing submersible cable flat PVC insulated & PVC sheathed 1100 volts grade with stranded copper conductor 3 core of size 16 sqmm conforming to IS-694-1990 including taking out old UNSV cable from its position and complete as specified.
Ditto all as per serial item No 20 described here-in-before but of size of cable 10 Sqmm 3 core complete all as specified..
Material & Labour for replacement of worn out MS Angle clamps nuts, bolts, washers etc of suitable length and size as per site requirement for flanged pipes and fitting of sizescomplete all as specified.
Supply and fix in repair water pressure gauge 0-350 PSI complete all as specified.
Supply and fixing steel rope 6 sqmm PVC coated all as specified.
S&F Fully Automatic Star- Delta Starter in sheet-steel enclosure motor rating, 415 V, 50Hz, 3Ph of capacity 30 HP relay range 26-40 A complete all as specified.
S&F Fully Automatic Star- Delta Starter in sheet-steel enclosure motor rating, 415 V, 50Hz, 3Ph of capacity 20 HP relay range 22-30 Acomplete all as specified.
Supply and fix CI sluice valve Cast iron PN-1.6 flanged end conforming to IS -780/84 with CI wheel, brass spindle, chuck nuts, rubber gasket, bolts (full threded), nuts & washers including joints for the following sizes complete all as specified and directed including dismantling and taking down of old unserviceable CI Sluice valve from existing position :
150mm dia
100mm dia
Supply and fix in repair lever operated butterfly valve 150 mm dia with complete accessories such as rubber gasket, bolts (full threded), nuts & washers including joints for the following sizes complete all as specified. (Make : Hazara/Upadhyay) :-
Supply and fix valve ( NRV ) reflux flanged end of size 150 mm dia incl making necessary joints dismantalling and taking out old u/s NRV complete all as specified.
Development of deep well as per the following procedure with entire satisfaction and testing on completion all as specified :- a) Lowering of GI Pipe 50mm dia upto 200 feet depth in side the casing of bore well and inserting rubber hose steel coil liner through the GI pipe including processing chemical of sodium laxate/caustic soda in required quantity for treatment of muddy water and injecting compressed air through hose pipe till clean water is received ( 8 hours continuous run minimum of two days )and taking out GI pipe and rubber hose air liner from its position complete including Lifting/lowering of pump with motor and column pipe with all accessories including electrical and mechanical connection as per existing including testing complete all as specified.
M&L for earthing with galvanized steel earth plate electrode 60 cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m below normal ground level) with top edge of earth plate not less than 1.5 m below normal ground level connected to galvanized earth lead strip 25x4mm (earthing lead from earth electrode to test point uopt 7.5m ) by means of bolts, nut, checknuts and washers of galvanized iron or steel all as shown in electrical plate No 5 of MES Schedule Pt-I 1991, GI earth lead strip of size 25mmx4mm protected by GI pipe 40mm dia light grade and connected to earth test point including excavation & earth work in any type of soil, disposal of soil, providing charcoal dust and common salt upto 15cm above top edge of earth plate, construction of PCC pit with RCC cover, funnel, watering pipe of 20 mm dia GI light grade including testing on completion complete all as specified.
M&L for repairing of motor controll Panel suitable for upto 50 HP motor with dismantling all unserviceable fitting and electric connection and reassembling the same after carry out the following replacement/jobs and painting with two coats of synthetic enamel paint over a coat of primer after prepartion of internal and external surface. Testing on load all complete as specified. (Note : Accessories to be replaced shall be measured and paid separately as mentioned here-after.
Supply only following spares for motor control Panel auto transformer starter of capacity upto 50 HP :- (a) Voltage sensing Phase failure relay, auto reset 40 Volt unbalance -01 No (Make : Model ALV D2 of MINILAC or Equivalent of L & T/GE POWER CONTROL)
Power contactor suitable for operation on 03 Phase, 415 Voltage, 50Hz AC supply type MNX 45 (Make : Cat No : ST 19000 of L&T or Equivalent of SEIEMENS/ HAVELLS)
Power contactor suitable for operation on 03 Phase, 415 Voltage, 50Hz AC supply type MNX 95 (Make : Cat No : ST 19000 of L&T or Equivalent of SEIEMENS/ HAVELLS)
Pump protection relay, 03 Phase 415 Volt AC supply auto reset. (Make : Model SPG-D2 of MINILAC or Equivalent/BCH/L&T)
Volt meter 0-500 Volt square type 96mm x 96mm size (Make :Model No SMR-96 of AE or Equivalent of HAVELLS/GE POWER CONTROL)
Ammeter 0-100 Amp. Square type 96mm x 96 mm size (Make :Model No SMI-96 of AE or Equivalent of HAVELLS/GE POWER CONTROL)
Indicator lamp ( RED, YELLOW and BLUE), Volt with built in resistor. (Make : SIEMENS/L&T/GE POWER CONTROL)
Indicator lamp holder (Make : SIEMENS/L&T/GE POWER CONTROL)
Push button switch for starter ON/OFF. (Make : SIEMENS/ L&T/RASS CONTROL)
CT Coil 100/5 ratio. Make : L & T/AE or Equivalent)
Analog timers 24 hrs type J648B1 for 415 Volt, 50 Hz. (Make : L&T/MDS/INDO ASIAN).
Current sensor of for 50 HP. (Make : Model CTS-80 of MINILAC or Equivalent of BCH/L&T)
Single pahse preventor, 415 Volts type ES-100 suitable for 50 HP motor 01 Nos
M K Engineering WOrks (BID ID -3451602)
M/S Pradeep Enterprise (BID ID -3451379)
M/s. RAMPHAL GARG (BID ID -3452007)
M/S DELTA ENGINEERS & CO (BID ID -3451872)
N K Construction (BID ID -3451123)
M/S S.K. CONSTRUCTION (BID ID -3451930)
stage.html
html • 0.06 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.48 MB
Tenderdocus8810.rar
Tender Documents • 1.39 MB
BOQ_812605.xls
BOQ • 0.38 MB
8810-Date_1.pdf
PDF • 0.19 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .