COMPREHENSIVE MAINT CONTRACT FOR ATTENDING DAY TO DAY B/R ANDE/M COMPLAINTS FOR ALL OFFRS / JCOs /OR MD ACCN AND JOINERY WKS INCLUDING FLY PROOFING AND RPR / REPLACEMENT, CLEANING OF SEWAGELINE, MANHOLE ETC INCLUDING SEPTICTANK, SOAK PITS AT AA BNR

Amount

Attending and checking complaints for plumbing work (leakage/unserviceable of all types of sanitary fittings and GI Pipes, of any dia) , Carpenter work (all type of joinery work for wooden, steel, aluminium) and welding work (Any type of steel work such as rolling shutter ,windows, door frame, gate and other iron works) or any other B/R complaints of subject CA etc complete all as directed and specified. Note : 1.Major parts such as Spindles/phases of CP pillar cocks, wall mixer, WHB mixer, Two way bib taps, CP bib cocks, Angle/stop cocks replaced if any shall be measured and paid for separately under respective item. 2.New GI pipes replaced if any shall be measured and paid under respective item of this schedule as S&F. 3.The contractor shall be provided all types of tools and equipments for joinery work such as drilling machine (with all type of drilling rod), cutting blades, Screw tightening machine, nail (any type and size) etc. 4.The contractor shall be provided welding machine , welding rod , gloves, welding glass or any other tools as required completed all as specified and directed by Engr-in charge.

Attending complaints of leakage/unserviceable, low level flushing cisterns, PVC pipe/seat cover and connections or chinaware for making it fully functional and leak proof by replacing the defective parts such as rubber washers, PVC levers, PVC/CP/brass knobs if required complete all as directed and specified

Attending complaints of internal water supply pipes, fittings and bottle traps for removing of blockages etc of any description including removing & cleaning of air locks etc, by pressure pump or any other means including taking down and refixing of pipes & fittings and replacing old unserviceable pipes and fitting with new ones complete all as specified and as directed. Note : New GI pipes replaced if any shall be measured and paid under respective item of this schedule as S&F. This item includes for labour part only for removal of blockage of air lock etc.

Note for Item 1 to 3 :-

(i) Contractor or his supervisor / site Engineer will report daily at 900 hrs at complaint cell for collection of complaints from the concerned JE in Charge in case after checking & attending the defects, if it is not possible to rectify the defects within 08 hrs , the facts shall be brought to the notice of JE than after to Engineer in charge by the contractor/ his rep immediately. If Engineer-in-Charge is satisfied with contractor view, no recovery will be made on this account. However complaints related to sewage line blockage/pipe replacement etc whatever is applicable shall be attended on same day whether it is 'Sunday' or 'Gazetted hoidays' and nothing extra shall be payable to contractor on this account.

(ii) Contractor or his supervisor/site engineer will report daily at 0900 hrs at complaint cell for noting of day to day complaints in complaint register, issue of complaints slip to tradesmen and enter after completion in complaint register.

(iii) The complaint shall be attended & defect shall be rectified within 08 hrs i.e from 0900 hrs to 1700 hrs excluding Sunday and Gazetted holiday commencing from date and time of notifying the complaint slip failing which a penality @ Rs 500/- per complaint per day (08 hrs) shall be levied upon/ imposed on the contractor and necessary recovery shall be made from his dues on this account. The contractor at the begining of contract will provide printed 30X complaints slip books as per performa let with 400 leaf each booklet.

(iv) Any item / material which are required to be replaced shall be paid under respective item under this schedule here in after as Supply only

(v) The labour/tradesmen required for replacement of 'Supply only' items are included under this item. However labour charges for items where indicated 'M&L', 'S&F' and 'in repairs' shall be included in respective items.

(vi) The above all aspect shall deemed to be included in the quoted rate of the respective item

Taking down shutter and refixing the shutter in same opening after making necessary repair to shutter of any description exc 1.0 Sqm but not exc 2.0 Sqm each complete all as specified.

Resecuring or easing & adjusting without taking down shutters of any description exc 1.0 Sqm but not exc 2.0 Sqm each complete all as specified.

Taking down shutters of any description exc 1.0 Sqm but not exceeding 2.0 Sqm complete all as specified.

Taking down shutters of any description exc 2.0 Sqm complete all as specified.

Taking down chowkhats or frame with out shutters of any description not exc 1.5 Sqm each including cutting holes of approriate size for hold fast blocks complete all as specified.

Taking down chowkhats or frame with out shutters of any description exc 1.5 Sqm including cutting holes of appririate size for hold fast blocks but n.exc 4.0 Sqm each complete all as specified.

Taking down chowkhats or frame with shutters (w/o taking off shutters from frames) n.exc 1.5 Sqm each as of any size and description complete all as specified.

Taking down chowkats or frames with shutters exc 1.5 Sqm but not exc 4.0 Sqm each (w/o taking off shutters from the frames) complete all as specified.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat of size 65x100mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200N (Face) & 1100N (Edge), minium compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resitance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately) Note : For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat of size 65x125mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200N (Face) & 1100N (Edge), minium compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resitance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately) Note : For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F mild steel work as in band strap, supports or stays for rainwater, hold fasts etc , conforming to to Fe-290 Gde E-165 complete all as specified.

Material and labour for PCC (1:2:4) type B1 using 20mm graded stone aggregate as in blocks for hold fast iron including necessary form work complete all as specified.

M & L for rolled mild steel of Gde Fe-290(Gde E-165) for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc (hold fast , coolar stand), complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete all as specified.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, fixing in opening as per specification complete all as specified.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing all as directed by Engineer-in-Charge.

S&F 30mm thick 2nd class hardwood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified.

S&F 35mm thick 2nd class hard wood glazed and skelton shutters open rebated and prepared to receive wire,gauze, glass etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified

S&F 30mm thick factory made Flush shutters, solid core construction, with particle board core and plywood face panels, one face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed by Engr-in-Charge.

M&L for factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Sspension Grade), calcium carbonate and natural fibers (wood powder/rick hust/wheat hust) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary SS screws shall be paid separately)

M &L for fabrication of pressed steel cupboard shutters using 1.00 mm thick MS plain sheet & with frame 1.25 MM thick bent to shape incl two coats of syn enamel paint on int surfaces & two coats of hammer tone finish on external surfaces alongwith locking arrangement mortice lock handle etc complete all as specified and directed

Taking down aluminium door shutter (exc 1.5 Sqm but not exc 2.5 Sqm) and refixing in the same opening of position after making necessary repair and making good the existing surface (with out change of rubber neoprene gasket packing) complete all as specified.Note:- Builders hardware used in repair shall be measured and paid separately.

Taking down aluminium door shutter (exc 1.5 Sqm but not exc 2.5 Sqm) each and refixing in the same opening of position after making necessary repair and making good the existing surface with change of rubber neoprene gasket packing etc complete all as specified and directed by Engr-in-Charge. Note for Item No 21.00 & 22.00 : Builders hardware used in repair shall be measured and paid separately.

S&F powder coated of any colour aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat complete all as specified. Note:- Thickness of powder coating shall not be less than 50 micron.

S&F powder coated aluminium door shutters, aluminium section weighting 0.55 Kg/RM including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos, in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified and directed by Engr-in-Charge. Note:- Thickness of powder coating shall not be less than 50 micron.

S&F powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighting 0.55 Kg/RM including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed by Engr-in-Charge.

M&L for aluminium anodised grill of 6-7 mm thick of 50x50 mm mesh size , medium grade and weight not less than 2.5 Kg/Sqm (anodised transparent or dyed o required shad according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design / pattern with approved standard section and fixed to the existing window frame with CP brass/stainless steel screws @ 200 mm centre to centre ,including cutting grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening and fixed at outer edge of aluminium doors/windows/ventilators complete all as specified and directed by Engr-in-Charge.

S&F 150mm aluminium anodised, barrel tower bolts of extruded section complete all as specified.

S&F 150mm extruded aluminium alloy handles, fabricated type polished complete all as specified.

S&F 100mm long Stainless Steel butt hinges (ISI marked) medium weight complete all as specified.

S&F 100mm long butt hinges 16 gauge (ISI marked) medium weight cold rolled mild steel complete all as specified.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

S&F 150mm long single action spring hinges, mild steel with steel wire spring stone enamelled black include welding to frame complete all as specified.

S&F 150mm, helical spring mild steel including welding to existing frame,complete all as specified and directed.

S&F 200mm long mild steel barrel tower bolts stove enamelled black with bright bolt complete all as specified.

S&F 150mm long mild steel pressed handle, oval type, stove enamelled black complete all as specified.

S&F Aluminium floor door stopper (overall length of cover plate 140mm) with suitable stops (double) fixed in wooden door to stop complete all as specified and directed

S&F Mortice Lock vertical type 4 levers 100mm size of mild steel body of approved make with two sets of keys complete all as specified.

S&F 4.80 mm thick sheet glass ordinary quality and glazing with aluminium snap beading in square exc 0.50 Sqm in each pane complete all as specified.

S&F door closer of hydraulically regulated designation No 3 universal type, (ISI marked) suitable for door shutters of 851 to 1000mm in width & 61 to 80 Kg weight complete all as specified.

S&F factory made steel windows box type using ERW hollow P section including box type hinges with steel handle, tower bolt, peg stay and hold fast complete with glazing bars dovetailed or welded complete with cooler opening all as specified including repairs to jambs in cement mortar with side hung shutters complete all as specified and directed

S&F factory made steel windows box type using ERW hollow P section including box type hinges with steel handle, tower bolt, peg stay and hold fast complete with glazing bars dovetailed or welded complete without cooler opening all as specified including repairs to jambs in cement mortar with side hung shutters complete all as specified and directed

S&F factory made steel windows box type using ERW hollow P section including box type hinges with steel handle, tower bolt, peg stay and hold fast complete without glazing bars dovetailed or welded complete with cooler opening all as specified including repairs to jambs in cement mortar with side hung shutters complete all as specified and directed

S&F factory made steel windows box type using ERW hollow P section including box type hinges with steel handle, tower bolt, peg stay and hold fast complete without glazing bars dovetailed or welded complete without cooler opening all as specified including repairs to jambs in cement mortar with side hung shutters complete all as specified and directed

S&F steel ventilator with centre hung shutter including box type hinges with steel handle and steel peg stay complete with glazing bars complete all as specified and directed.

S&F steel ventilator with centre hung shutter including box type hinges with steel handle and steel peg stay complete without glazing bars complete all as specified and directed.

Supply and fixing Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed by Engineer-in-charge.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm with stainless steel wire staples complete all as specified and directed by Engr-in-Charge.

S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm with stainless steel wire staples complete including wooden beading if required as per site requirement all as specified.

Hacking out old broken glass (any thickness size quality in description from metal frame including punching or drilling old glazing/springs clips and providing and fixing new one complete all as specified.

M&L for 4mm thick, plain acrylic sheet fixing in steel/metal frame in square not exc 0.50 sqm in each pane fixing with steel self drilling screws complete all as specified.

M&L for 4mm thick figured acrylic sheet, pin headed type and fixing in steel/metal from in square not exc 0.5 Sqm in each pane fixing with steel self drilling screws complete all as specified

Demolition of reinforced cement Concrete in Roofs, floors (other than ground floors), beams staircases, landing, chajjas, roof projection in D/S bldgs and similar suspended work complete all as specified and directed

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels,plates etc, including welding,grinding ,buffing,polishing and making curvature ( whereever required) and fitting the same with necessary stainless steel nuts and bolts complete all and including fixing the railing with necessary accessories and stainless steel dash fasteners , stainless steel bolts etc , of required size , on the top of floor or the side of waist slab with suitable arrangement all as directed by Engr in Charge.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamelled paint over one coat of pink primer complete all as specified.

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamelled paint over a coat of red oxide primer complete all as specified.

M&L for welding in repairs exc 2.5 cm but n. exc 5 cm in length on steel surfaces of thickness exc 20 mm but n. exc 25 mm complete all as specified.

M&L for 25mm Box Type butt hinges for steel window/ventilators fixing with welding minimum thickness of 20mm including dismantling of old projecting type butt hinges complete all as specified

Taking down cement plaster from concrete/stone surfaces including raking out joints, hacking for key, scrubbing down with water etc and its removal from site complete all as specified.

M&L for 15mm thick, rendering in Cement mortar (1:6) on wall of stone surfaces & finished even & smooth w/o using extra cement complete all as specified.

M&L for 15mm thick, rendering in Cement mortar (1:4) on wall of stone surfaces & finished even & smooth w/o using extra cement complete all as specified.

M&L for preparation of new plastered surfaces on internal walls & applying two coats of oil bound distemper overe one coat of primers to match with existing color complete all as specified.

M&L for preparation of new plastered external surfaces & applying two coats of cement base paint to match with existing color complete all as specified.

S&F in repair 100mm long butt hinges 16 gauge (ISI marked) medium weight mild steel all as Specified Engineer-in-Charge.

S&F in repair Continuous (piano) hinges, Width of flaps (when open in mm), mild steel, bright finish or electrogalvanised complete all as specified and directed

S&F in repair 150mm long single action spring hinges, mild steel with steel wire spring stone enamelled black. (ISI Marked)

S&F in repairs 300 mm long mild steel sliding door bolt plate type, stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed by Engineer-in-charge.

S&F in repair 200mm long Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed to door complete all as specified and directed

S&F in repair 150mm long Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed to door complete all as specified and directed

S&F in repair 150mm long Mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed

S&F in repairs 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed to door complete all as specified and directed by Engineer-in-charge.

S&F in repair 150mm long Aluminium anodised, barrel tower bolts of extruded section and fixed to door complete all as specified and directed

S&F in repair 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed

S&F in repair Mortice lock vertical type 4 levers 100mm size of brass body with two sets of keys complete all as specified directed by Engineer-in-Charge.

S&F in repair door closer (Aluminium extruded section body) hydraulically regulated designation No 3 universal type, (ISI marked) suitable for door shutters of 851 to 1000mm in width & 61 to 80 Kg weight complete all as specified directed by Engineer-in-Charge.

S&F in repair 50mm dia, cupboard knobs fixed with nut, screw and washer of polished brass complete all as specified and directed

M&L for 150mm overall length of cover plate floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed

S&F in repair 300mm long helical spring mild steel including welding to existing frame complete all as specified and directed

S&F in repair 65mm Brass Lever locks for cupboard grade I, complete all as specified and directed

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty fixed to floor complete all as specified and directed

S&F in repair 25 mm internal dia Stainless Steel Curtain Rod including decorative type knobs at both ends of approved make including curtain bracket fancy type (two Nos of brackets/knobs/corners for one length/each opening) complete all as specified and directed

Dismantling floor hearth or wall tiling including cement mortar bedding (including not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for coloured Glazed ceramic tiles in vertical surface 350x250x7mm/450X300X7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles in vertical surface including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for coloured non-skid ceramic tiles 7 to 8mm thick (square/rectangular), coloured tiles, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floorts etc, set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick screed bed in CM 1:6 all as specified and directed.

Taking up or down steel tubing and connection including cleaning for refixing or removal to store yard of bore 15mm complete all as specified and directed

Taking up or down steel tubing and connection including cleaning for refixing or removal to store yard of bore 20 mm complete all as specified and directed.

Taking up or down steel tubing and connection including cleaning for refixing or removal to store yard of bore 40 mm complete all as specified and directed.

S&F 16mm outer dia CPVC pipes plain with fittings on walls/ceiling or laying in floors including necessary fittings complete all as specified and directed.

S&F 20mm outer dia CPVC pipes plain with fittings on walls/ceiling or laying in floors including necessary fittings complete all as specified and directed.

S&F 40mm outer dia CPVC pipes plain with fittings on walls/ceiling or laying in floors including necessary fittings complete all as specified and directed.

S&F in repair 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed.

S&F in repair 40mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed.

S&F in repair 15mm dia stop valves, screwed down high pressure, screwed both ends for iron pipe or for unions and fixed for 15mm bore but fancy type, chromium plated with long shank and cup (concealed type) complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15mm dia Stop valves/angle valve, fancy type, chromium plated screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore complete all as specified and directed.

S&F in repair CP 15mm dia bib tap cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repair brass chromium plated shower rose 125mm size complete all as specified and directed by Engineer-in-Charge

S&F in repair PVC connections 15mm size with PTMT nuts of length 600mm all as specified and directed.

S&F in repair 10 ltr PVC valve less, symphonic action type dual type flushing, low level, white, with inlet ball valve, float and handle including 600mm long PVC connection and brackets complete all as specified and directed by Engineer-in-Charge

S&F in repairs vitreous china squatting pan, Órrisa Pattern' size 580mmx440mm white with integral foot rests, embedded and set in PCC 1:5:10 type E2 (using 40mm stone aggregate) and making good to dismantled floor including removing rubbish complete all as specified and directed by Engineer-in-Charge

S&F in repair Vitreous china wash hand basin (550X400mm) white, flat back excluding taps, including brackets & 32mm waste cuppling chromium plated complete all as specifed and directed.

S&F in repair for Vitreous china bowl urinal flat back size of 465 x 355 x 265mm white (minimum) with grating and union for discharge pipe completed all specified and directed by Engineer-in-charge.

S&F repairs Viterous China wash down water closet pan (pedestal pattern) white complete all as specified and directed by Engineer-in-charge.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair grating doom 100mm dia of PTMT (min weight 25 gms) complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F framed work such as grills, grating etc with ends of bars shouldered and or riverted or forged into spike framed guard bars,; barred iron doors; ladders; framed baulustes; walk ways; railings; framework of water tanks and similar work conforming to Fe-290, Gde E-165 including cutting holes and fix fasterners etc complete all as specified and directed

M&L for two coats of synthetic enamel paint over a coat of red oxide as priming coat including preparation of newly treated steel surfaces of girth n exc 10 cm complete all as specified and directed

Cleaning and removing all scale and dirt etc of storage water tanks of capacity exc 500 ltrs but n exc 1000 ltrs including cleaning of mouths of circulating pipes by appliying bleaching powder and brushing with wire brushes taking out all scales etc cleaning of tank become clear all as specifed and directed.

Cleaning and removing all scale and dirt etc of storage water tanks of capacity exc 250 ltrs but n exc 500 ltrs including cleaning of mouths of circulating pipes by appliying bleaching powder and brushing with wire brushes taking out all scales etc cleaning of tank become clear all as specifed and directed.

S&F in repair ISI marked 500 Litre capacity rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm brass ball valve high pressure and tank connection including dismantling of the old unserviceable water tank with all accessories complete all as specified and directed by Engineer-in-Charge.

S&F in repair ISI marked 1000 Litre capacity rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm brass ball valve high pressure and tank connection including dismantling of the old unserviceable water tank with all accessories complete all as specified and directed by Engineer-in-Charge.

S&F in repair ISI marked 2000 Litre capacity rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 25mm brass ball valve high pressure and tank connection including dismantling of the old unserviceable water tank with all accessories complete all as specified and directed by Engineer-in-Charge.

S&F in repair Sheet Glass Shelf assembley of 5.5mm thick sheet glass shelf 12 cm wide with chromium plasted bracked guard and railing 60CM long as approved by Engineer-in-Charge

Dismantling of 100mm dia cast iron pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

S&F100mm dia cast iron soil waste and vent pipes ISI marked in any length with or without ears using cement joints fixed in with cement joints, laid in trenches or in floors complete all as specified and directed.

S&F100mm dia cast iron soil waste and vent pipes ISI marked in any length with or without ears using cement joints fixed in walls complete all as specified and directed.

Dismantling of 75 mm dia cast iron pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

S&F 75mm bore dia cast iron soil, waste and vent pipes, sand cast, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

S&F 75mm bore dia cast iron soil, waste and vent pipes, sand cast, in any length with or without ears, with cement joints, fixed in wall complete all as specified and directed.

S&F 100mm dia CI Tee branch single (equal or unequal) ordinary or inverted (spigot or socket type of or with paralled branches with oval access door complete all as specified and directed.

S&F 100mm dia CI Tee branch single (equal or unequal) ordinary or inverted (spigot or socket type of or with paralled branches without oval access door complete all as specified and directed.

S&F in repairs 100mm dia CI bends (any radious) diminishing pieces or tapers (larger bore shall be measured) with oval access door complete all as specified and directed.

S&F 100mm cast iron cowl complete all as specified and directed.

S&F in repairs 15 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum wt 15mm-142 gms) complete all as specified and directed

S&F in repairs 20 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum wt 20mm-210 gms) complete all as specified and directed

S&F in repairs 25 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum wt 25mm-455 gms) complete all as specified and directed

S&F in repair Vitreous China white Soap Dish approximate 160x160x90mm complete all as specified and directed

S&F in repair Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device for pedestal pan complete all as specified and directed

S & F in repair 15mm bore bib taps Standard of PTMT any colour high pressure, screwed both ends for iron pipe or for brass ferrule (min weight 15mm-90gms) complete all as specified.

S&F in repairs 15mm bore Pillar taps fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified

Removing of existing filling in sunken floor of WC and repair to sunken floor with 15mm thick plastering in CM 1:3 of internal surface mixed with WPC, than painting with bitumen 30/40 over a coat of bitumen primer, putting 50 micron polythene than filling with PCC 1:5:10 type E-2 using 40mm graded stone aggregate and inserting 50mm bore 1.00M long GI water tubing to the wall complete all as specified and directed by Engineer-in-Charge. Note : WC and tiles shall be measured and paid separately.

S&F in repair Stainless steel kitchen plate rack 1.0mm thick of size 750 x 600 x 250mm complete all as specified and directed by Engineer-in-charge.

S&F in repair bath cabinet of PTMT fixed with and including chromium plated brass screws and wooden cleats size 355mmx455mm complete all as specified and directed

S&F in repair Stainless steel peg set of 5 size 300x25&2mm thick complete all as specified and directed

S&F in repair 32mm PVC waste pipe for sink/WHB complete all as specified and directed

S&F in repair 40mm PVC waste pipe for Urinal complete all as specified and directed

S&F in repair Lid cover for PVC water tank with 4 Nos nut & bolt suitable for 500&1000 ltr capacity water tank complete all as specified and directed

S&F in repair Door Seal 25mm size door seal bottom, door Air Gap rubber shield 0.90 to 1.00 mtr for covering gaps between door and floor to avoid entry of insects, dust , anti rust all complete all as specified and directed

S&F in repair stainless steel 125mm dia sink coupling complete with rubber seal for water disposal/storing equipment including waste pipe complete all as specified and directed

S&F in repair 15mm size and 50mm long CP nipple complete all as specified and directed

S&F in repair brass spindle suitable for 15mm dia CP Tap, CP stop cock short body/long body/CP Pillar Cocks & Brass Bib Tap complete all as specified and directed

S&F in repair PVC internal fitting of low level flushing cistern with syphon, handle lever etc complete kit complete all as specified and directed

S&F in repair CP wall mixture 3-In-1 system provn for overhead & telephonic shower complete with 115 long bend pipe, connecting legs and wall Flange complete all as specified and directed

S&F in repair 15 mm chormium plated angle cock two way cast copper alloy complete all as specified and directed

S&F in repair CP jet spray with flexible tube etc complete all as specified and directed

S&F in repair health faucet (hand shower) (ABS Body) with 1.2 mtr long flexible tube and wall hook etc complete all as specified and directed

S&F in repair brass chromium plated/ stainless steel soap tray/ dish fixed with CP screws complete all as specified and directed

S&F in repair stainless steel Towel Rack withlower hanger size 24'' (600 mm ) fixed to walls hook etc complete all as specified and directed

M&L for 18 mm thick solid PVC sheet UPVC Coated Celuka printed in one of two different colours( with wood grain printed pattern/ivory colour finish) as in kitchen cabinet shutters ,all round body of cabinets , shelves ,drawers etc cut to required size jointed with solvent cement & steel screws etc complete all as specified & directed .

Extra over PVC boards for lipping 1-1.5 mm thick 18 mm wide complete all as specified and directed

S&F 0 degree clip type self closing hinges for cabinets fized with cadimum coated screws all as per sample.

S&F 100mm size bright finished cromium plated steel handle of approved shape & design fixed with cadmium coated screws on the kitchen cabint shutters complete all as specified and directed

S&F 75mm size bright finished cromium plated steel handle of approved shape & design fixed with cadmium coated screws on the kitchen cabint drawers complete all as specified and directed

S&F magnetic catches for cabinets of size 50 mm complete with striking plate & magnetic stud complete all as per approved smaple.

M&L for excavation in trenches n.exc 1.5m wide and 1.5m deep for foundation etc or for shafts, well, cesspits manholes etc n.exc 10 sqm on plan and getting out hard/dense soil complete all as specified and directed by Engineer-in-charge.

Returning fillling in including spreading levelling watering and well ramming in layers n.exc 25cm in hard/dense soil complete all as specified and directed by Engineer-in-charge.

Removing excavated soil to a distance n exc 50m depositing directed at a level n.exc 1.5m above the starting level complete all as specified and directed by Engineer-in-charge.

Demolition and breaking up drain pipes (AC or reinforced concrete) of internal dia 100mm set in cement mortar of any description including the Demolition of PCC under and haunching etc complete all as specified and directed by Engineer-in-charge.

Demolition and breaking up drain pipes (AC or reinforced concrete) of internal dia 150mm set in cement mortar of any description including the Demolition of PCC under and haunching etc complete all as specified and directed by Engineer-in-charge.

Demolition and breaking up drain pipes (AC or reinforced concrete) of internal dia 200mm set in cement mortar of any description including the Demolition of PCC under and haunching etc complete all as specified and directed by Engineer-in-charge.

M&L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate in concrete bedding to drain pipes 100mm bore including packing under and completely surrounding pipes with concrete after they are laid and tested complete all as specified and directed by Engineer-in-charge.

M&L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate in concrete bedding to drain pipes 150mm bore including packing under and completely surrounding pipes with concrete after they are laid and tested complete all as specified and directed by Engineer-in-charge.

M&L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate in concrete bedding to drain pipes 200mm bore including packing under and completely surrounding pipes with concrete after they are laid and tested complete all as specified and directed by Engineer-in-charge.

M&L for 100 mm dia High density polyethylene pipes (HDPE) of pressure rating 10 kgf/cm2 laid and jointed complete with collars, laid in trenches and jointed and tested complete all as specified and directed by Engineer-in-charge.

M&L for 150 mm dia High density polyethylene pipes (HDPE) of pressure rating 10 kgf/cm2 laid and jointed complete with collars, laid in trenches and jointed and tested complete all as specified and directed by Engineer-in-charge.

M&L for 200 mm dia High density polyethylene pipes (HDPE) of pressure rating 10 kgf/cm2 laid and jointed complete with collars, laid in trenches and jointed and tested complete all as specified and directed by Engineer-in-charge.

Checking and attending to cleaning and maintenance of sewage line system, including blockage/choke in WHB, bottle traps, kitchen sink/Nahani traps/Floor traps, water closet, soil/waste pipe running on external walls of bldgs including junction holes of any description and sewage line of any size ,blockage of any description in any situation manually and mechanically as required including all equipments viz bamboo, tools, sewage pump, sewage machine etc including replacement of defective items/materials and refixing covers to manholes/gully trap in position etc. After cleaning and removing the deposited sludge/solid/liquid material outside MD land complete all as specified and directed.

Attending daily complaints of Jodhpur Mil area by deputing adequate number of teams of qualified Electrician and helper (round the colck) for repair, maintenance and making the continuity of supply after rectifying the defects of the electrical system by replacing the U/S items such as switches, sockets, distribution boards, MCB light/power , lamp holders-bracket/ pendent/ batten, bell/ buzzer , push button, ceiling rose, capacitors and other similar, light & power plug, including provisioning of small pieces of electrical cables PVC insulated copper multistranded conductor of sizes 1.5 Sqmm to 6 Sqmm single core and length not increasing 0.50 mtrs complete all as specified and directed by Engr-in-Charge. (Complaint slip shall be part of the bill). Note:- (i) Contractor shall be fully responsible for Complaint slip/ Job card prepared and submitted on daily basis (ii) This item pertains to attending complaints of light/fan/power point, MCB DB including other minor items such as insulating tape, screws etc as required to attend the complaint to the entire satisfaction of user/Engr-in-Charge. (iii) Items shall be measured and paid seperately under respective item of Sch 'A'

M&L to attend major/ minor fault/ No Light due to any reason like neutreal fail or short cicuit complete including petroling or rectfication of complaint etc., complete all as specified and directed.

Supply and fixing in repalcement switch piano flush type 6 amp single pole one way 230 V incl dismentling of old unserviceable switch of any make, complete all as specified and directed.

Supply and fixing repair switch piano flush type 6 amp single pole two way 230 V incl dismentling of old unserviceable switchof any make, complete all as specified and directed.

Supply and fixing in replacement switch piano flush type 16 amp single pole one way 230 V incl dismentling of old unserviceable switch of any make, complete all as specified and directed.

Supply and fixing in replacement bell push AC, 230 Volts, 5 Amps incl dismentling of old unserviceable bell push of any make, complete all as specified and directed.

Supply and fixing in replacement socket out let flush type 6 amp 3/5 pin suitable for 6 Amp plug top 230 V incl dismentling of old unserviceable socket of any make all as specified & directed.

Supply and fixing in replacement socket out let flush type 3/6 pin suitable for 16 Amp plug top multipurpose 230 V incl dismentling of old unserviceable socket of any make all as specified & directed.

Supply and fixing repair bell AC ding dong type 230 volts incl taking down old unserviceable bell, complete all as specified and directed.

Supply and fixing in replacement fan regulator electronic switch/ socket type incl dismentling of old unserviceable regulator complete all as specified and directed.

Supply and fixing in replacement lamp holder insulated body with back plate batten/angle type for batten fittings incl taking down old unserviceable holder complete all as specified and directed

Supply and fix in replacement fan capacitor 2.5 m.f.d for ceiling Fan, incl taking down old unserveable capacitor all as specified and directed

Supply and fix in replacement fan capacitor 4 m.f.d for Exhaust Fan,incl taking down old unserveable all as specified and directed.

Supply and fixing in replacement ceiling rose 3 terminals complete incl taking down all as specified and directed.

Supply and fixing in replacement Modular switch any type and make 6 amp one way 230 V incl dismentling of old unserviceable switch of any make all as specified & directed .

Supply and fixing in replacement Modular switch any type and make 16 amp one way 230 V incl dismentling of old unserviceable switch of any make all as specified & directed.

Supply and fixing in replacement Modular socket Any Type and make, 6 amp 5 Pin one way 230 V all as specified & directed .

Supply and fixing repair Modular socket Any Type and make, 16 amp 5 Pin one way 230 V incl dismentling of old unserviceable switch of any make all as specified & directed .

Supply and fixing in replacement Modular switch any type and make 6 amp two way 230 V dismentling of old unserviceable switch of any make all as specified & directed .

Supply and fixing in replacement Modular fan Regulator step type and make, 100 watt , 230 Volts ismentling of old unserviceable regulator all as specified & directed .

Supply and fixing in replacement modular cover plate with frame 4 module type including concealed MS Box for fixing of modular switch socket, regulators, blank plates etc incl dismentaling old unserviceable cover plate complete all as specified and directed.

Supply and fixing in replacement modular cover plate with frame 8 module type including concealed MS Box for fixing of modular switch socket, regulators, blank plates etc incl dismentaling old unserviceable cover plate complete all as specified and directed.

Supply and fixing in replacement modular cover plate with frame 12 module type including concealed MS Box for fixing of modular switch socket, regulators, blank plates etc incl dismentaling old unserviceable cover plate complete all as specified and directed.

Supply and fixing in replacement PVC conduit including fitting such as tee,elbow,bend etc 20mm dia ISI (MMS)grade, incl taking down old unserviceable conduit all as specified and directed.

Supply and fixing in replacement PVC cassing Capping tee,elbow,bend etc 20/25 mm dia ISI (MMS) incl taking down old unservecable cassing capping all as specified and directed.

Taking down fan, cealing cable end,dismantling blades and removing fan and blades to store or repair (rewinding) and refixing in same position including connector from ceiling rose to fan connector complete.

Taking down exhaust fan and refixing after rewinding and connecting up including provision of cable from ceiling rose to connector to fan

Taking down bldg security light upto 45 watt and refixing the same after repair all as specified and directed by Engr -in-charge. Note:- Electronic driver are measured and paid sepearately.

M & L in replacement remote bell ding dong type all as specified and direcected incl taking down old UNSV bell by Engr-in-charge.

Supply and fixing PVC insulated and unsheathed FRLS single core multistranded copper conductor for repair, in existing conduit of size 1.5 sqmm as in replacement of any defective/burnt circuit incl taking down old UNSV cable, complete all as specified and directed.

Supply and fixing repair PVC insulated and unsheathed FRLS single core multistranded copper conductor for repair, in existing conduit of size 2.5 sqmm as in replacement of any defective/burnt circuit.incl taking down old UNSV cable, complete all as specified and directed.

Supply and fixing repair PVC insulated and unsheathed FRLS single core multistranded copper conductor for repair, in existing conduit of size 4.0 sqmm as in replacement of any defective/burnt circuit.incl taking down old UNSV cable, complete all as specified and directed.

Supply and fixing repair PVC insulated and unsheathed FRLS single core multistranded copper conductor for repair, in existing conduit of size 6.0 sqmm as in replacement of any defective/burnt circuit.incl taking down old UNSV cable, complete all as specified and directed.

Taking down carefully copper/aluminium point wiring for light, fan, bell socket power slocket etc complete with boards, outlet boxes fittings and fixtures such as switchs, sockets, lamp holders bracket, ceiling rose etc., complete all as specified and directed.

M&L for Point wiring complete with 1.5 sq mm single core multi stranded copper conductor PVC (FRLS) insulated unsheathed cable confirming to IS-694,1100 Volts grade passing in PVC cassing-N-capping 25/32 mm dia fixed on surface of wall/roof/ceiling with existing/new sunken pressed steel terminal boxes including 3.00 mm thick plastic laminated sheet top cover or (Surface PVC Box as directed by EIC) and 1.50 sq mm PVC insulated unsheathed stranded copper conductor(FRLS) cable for common earth and connecting to earth dolly material and labour for:-

One light point controlled by one, one way switch

One fan point controlled by one way switch.

One socket outlet 3 pin 5/6 Amps on same board

One socket outlet 3 pin 5/6 Amp on independent board

One bell point controlled by one bell push.

One light point controlled by two, two-way switches

All as per item No 205.00 above but with using 2.5 Sq mm single core multistanded copper conductor cable including 2.5 sq mm PVC insulated unsheathed stranded copper conductor for common earth wire for 6 pin 16 Amp socket outlet on independent board .

M & L for (concealed) point wiring in walls and surface on roof and hard srface of stone complete with multistranded copper conductor 1.5 Sqmm PVC insulated unsheathed single core FRLS cable 1100 volt grade, confirming IS 694 & colour code in conduit system of wiring, drawn through in and including non-metalic PVC concealed (including Cutting Chases and make good the distrubed surfaces ) conduit of size 20 mm or med grade as required as site, totally concealed in walls / and surface on floors / ceiling or fixed on surface of walls / columns / beam / tie beam etc by means of saddles and clips etc incl all conduit accessories / fittings / junction boxes / inspection covers etc of heavy grade, ISI marked and sunk terminal boxes of CI or 16 SWG pressed steel housing, totally concealed in walls with 3mm thick industrial laminated sheet top cover, fixed flush with wall surface by means of brass screws and sunk / cup washers, for mounting of switches, sockets fan regulators etc incl 1.5 Sqmm FRLS PVC insulated, unsheathed flexible multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, all as specified, directed and shown on drgs for The rates of chase cutting on wall done concealed conduit and steel terminal boxes are included in the unit rates all as specified and directed by Engr-in-Charge.

One light point controlled by one, one way switch

One fan/ Exhaust Fan point controlled by one way switch.

One socket outlet 3 pin, 5 Amps on independent board, controlled by one no 5 Amp switch.

One socket outlet 3 pin 5 amps on the same board controlled by one no 5 Amp switch.

One bell point controlled by one bell push.

One light point controlled by two, two-way switches.

All as per item No 207.00 above but with using 2.5 Sq mm single core multistanded copper conductor cable including 2.5 sq mm PVC insulated unsheathed stranded copper conductor for common earth wire for 6 pin 16 Amp socket outlet on independent board .

Supply and fixing repair one bakelite sheet not less then 3mm thick after removing all connection including cutting/chassing to accommedate existing fitment and making connection including cadmium plated screws with cup washer of fwg size:-

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S & F in replacement PVC Surface Box including and suitable for one 6 Amps switch and one 6 Amps sockets complete all as directed by EIC.

S & F in replacement PVC Surface Box including and suitable for one 6 Amps bell push and one 6 Amps switch complete all as directed by EIC.

S & F in replacement PVC Surface Box including and suitable for one 16 Amps switch and one 16 Amps sockets complete all as directed by EIC.

Note for all items:- (i)- Deployed Manpower for rectifying day to day complaints shall wear a dress proper as per different category of Manpower. (ii)- Dress code shall be differentt for plumber, carpenter, Blacksmith, Sweeper and Electrician etc., as approved by Engg-in-charge. (iii) A complaint cell shall established with each RWA office at a residential complex/enclave to attend and resolve all the day to day complaints of subject work with in stipulated time period and contractor shall deploy manpower/ tradesman like i.e. supervisor, attendent etc. with all requisite tool & plant for smooth functioing of comprehensive maintenance for subject work. (iv) The quoted rates shall be deemed to be included all provisions mentioned above.

INDO CONSTRUCTION