PROVN OF STORAGE SHED FOR FOL PM (WMR BARRELS) ALONGWITH FOL OFFICE AT 433 I SUPPLY DEPOT LANSDOWNE UNDER AGE (I) LANSDOWNE

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in hard/ dense soil comlete all as specified and directed.

Excavating in trenches n'exc 1.5 m width and n'exc 1.5 m in depth for foundation or for shafts, well cesspits, manholes etc / for laying of cable/ pipe etc n'exc 10 sqm on plan and n'exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed.

M&L for moorum / red bajri filling in, floor or pavings, laid in layers not exceeding 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for PCC (1:4:8) Type D2 (40 mm graded aggre-gate) as in foundations, filling and mass-concrete complete all as specified and directed.

M&L for RCC (1:2:4) Nominal mix (using 20mm graded stone aggregates) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles, raft etc and mass concrete complete all as specified and directed.

M&L for RCC (1:2:4) Nominal mix (using 20mm graded stone aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for RCC (1:2:4) Nominal mix (20mm graded aggregates) as in beam, lintel upto 1.5m span including formwork of rough finish surfsce complete all as specified and directed.

M&L for RCC (1:2:4) Nominal mix (using 20mm graded stone aggregates) as in Chajjas/ fins/ facia of roof slab complete all as specified and directed.

M&L for formwork for rough finish to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L for formwork for rough finish to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L for formwork for rough finish to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for formwork for rough finish to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 5 to 10mm dia bars as in stirrups cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed.

Removal of surplus soil to a distance n'exc. 50 Mtr and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

M&L for hardcore of broken boulders/stone of gauge n exc. 63 mm, deposited, spreading, leveling watering and well ramming to true surface in layers not exceeding 15 cm thick each layer complete all as specified and directed.

M&L for 75 mm thick PCC (1:4:8) type D2, (40 mm graded stone agg) as in sub base of floor/ hardstanding/ footpath complete all as specified and directed.

M&L for 20mm thick screed bed or bedding layer in CM (1:6) for laying floor finish complete all as specified and directed.

M&L for mirror polished machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab complete all as specified and as directed Note:- The size of kota stone slab not less than 550mmx550mm (cut size except the location where balanced.)

Description same all as per item No 20 above but, as in skirting/ dado (10-12mm thick Kota stone) over and including 15mm thick rendering in cement mortar (1:4) complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6), type C-2 using 40mm graded stone aggregate as in plinth protection, surface finished even & smooth without using extra cement, with and including joint filling (Size 30mm deep x 10mm wide) with sealing compound grade-A at 3m interwal and corner complete all as specified and directed.

M&L for brick work with fly ash old size brick straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

M&L for 15mm thick rendering on other than fair faces of brick work or concrete surface in cement plaster (1:6) finished the surface even and fair complete all as specified and directed.

M&L for 15mm thick plastering on fair faces of brick wall in two layers, Ist layer 10mm thick CM (1:6), and IInd layer 5mm thick CM (1:4), surface finished even and fair mixed with @ 200ml per bag WPC (liquid type) complete all as specified and directed. Note :- WPC (Liquid type) shall be measured and paid separately as supply only.

Supply only WPC integral water proofing compound (Liquid type) complete all as specified and directed.

M&L for preparation of newly plastered surface of external wall all as prescribed by manufacture of paint and applying two coats of exterior anti fungal acrylic emulsion paint (walmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of performance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of paint/ distemper by using roller/ spray machine with and including application of wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper complete all as specied and directed at site by Engineer-in-Charge.

M&L for preparation of newly plastered surface of interior wall by application of wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying two coats of acrylic distemper over a coat of primer of same make all as specified and prescribed by manufacture of paint/ distemper, by using roller/ spray machine complete all as specied and directed at site by Engineer-in-Charge.

S&F rolled mild steel section for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W(Gde-E-250) quality-A complete all as specified and as directed. Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete.

S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa, AZ-150 as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, AZ-150 as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed .

M&L for two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or grith complete all as specified and directed.

S&F framed work as in iron enclosure, doors or gate of angle iron or other section with gussets plate, rails, braces etc drilled for fixing of steel seating other covering, door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel handing door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing conforming to Fe-290 (Gde-E-165) complete all as specified and as directed. Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts), providing and fiitings angle cleats, fish plates, gusset plate etc., also for welding plumbing, truing up and fixing complete. No claim whatso ever shall be entertained by Govt on this account.

S&F factory made steel window or ventilators fixed type with glazing bars complete all as specified and directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty/ wooden/ PVC/ aluminium beading, in square n. exc 0.5 sqm in each pane complete all as specified and as directed.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and or riveted or forged into spikes, framed, barred iron door, ladders, fencing work ect. conforming to Fe-290 Gde E-165 complete all as specified and directed. Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts), providing and fiitings angle cleats, fish plates, gusset plate etc., also for welding plumbing, truing up and fixing complete. No claim whatso ever shall be entertained by Govt on this account.

Material & Labour for Point Wiring for one light Point/one fan point/ one call bell point, controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with continious earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed PVC conduit, "medium grade" (ISI marked) , not less than 20 mm dia duly concealed on wall/ceiling or above false ceiling with fittings medium grade (Color coding of wires shall be Phase, neutral and earth wire all as specified ) sunk Metal flush box with and incl decorative polycarbonate frame for housing Modular Switches, sockets , fan regulators etc including white cover plate complete all as specified and directed. Note:- (i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall deemed to be included in quoted rates. (ii) If the contractor fail to make good the disturbed surface of wall/ceiling etc and do not match with the existing surface of wall/ceiling to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

Description same all as per serial Item No 37 here in above but One 5 pin socket out let 5/6 Amp on same board complete all as specified and directed.

Description same all as per serial Item No 37 here in above but One 3pin/ 5 pin socket out let 5/6 Amp on independent board complete all as specified and directed.

Description same all as per serial Item No 37 here in above but with 2.5 Sqmm PVC insulated FRLSH cable for 15 Amps power point complete all as specified & directed.

S&F modular switch 5/6 Amp single pole one way 230 volts, 50 HZ conforming to IS: 3854 and ISI marked complete all as specified and directed. Make :- Make: Legrand cat No: 6734 01/ Indoasian Cat No: 800000/ Havells Cat Part No: ACWSXXW101

S&F modular switch piano, 1module, flush type button 15/16 Amp single pole one way conforming to IS: 3854 and ISI marked complete all as specified and directed. Make: Legrand cat No: 6734 11/ Indoasian Cat No: 800002/ Havells Cat Part No: ACWSXXW161

S&F modular socket outlet, 2 module, 2/3 pin 2 in 1, 5 Amps, flush type, 230 volts AC circuit complete all as specified and directed. Make: Legrand cat No: 6734 52/ Indoasian Cat No: 800020/ Havells Cat Part No: ACWKPXW063

S&F modular socket outlet, 2 module, 2/3 pin 2 in1, 15 Amps, flush type, 230 volts AC circuit complete all as specified and directed. Make: Legrand cat No: 6734 55/ Indoasian Cat No: 800022/ Havells Cat Part No: ACWKCXW163

S&F angle fency Lamp holder, insulated body, of PVC/ Polycorbonate with back plate (ISI Marked) suitable for batten fitting complete all as specified and as directed.

Supply and fixing ceiling rose surface bakelite 65/25 mm dia having three terminals ISI Marked complete all as specified & directed.

Supply and fixing sheet metal enclosure double door type for MCBs DB SPN (Single pole and neutral) 240V AC 8 way with 200 Amps rated bus bar complete all as specified and directed .

Supply and fixing MCB SP 6- 32 Amp 240 V AC 10 KA B curve rupturing capacity complete all as specified & directed.

Supply & fixing MCB, SPN, AC, 240 volts of 32 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs complete all as specified & directed.

S&F surface mounted LED luminiare 20 watt with all accessoried having polycarbonate extruded channel with diffuser for glare free light, high lumen output, driver PF >0.98 having over voltage protection upto 400 volts surge protection, level 7-10 KV thermal short circut protection THD<10%, made up of long life LED chips (SMD) in modular with Ra>70 and lumen efficiency >120 lumen perwatt, Inverter LED batten with square profile, inbuilt Lithium Ion battery with charging time 8-10 hours and back up time up to 4 hours, 6500 K internally pre-wired through flexible wire connection with ceiling rose complete all as specified and directed. Make :– Make – Shakti Fixtures Pvt Ltd, Cat Part No. SZSLBMX020 / Havells, Cat Part No. LHEXBLP7PN1W020 or equivalent of others make as specified. Note: The firm has to give warranty for fitting including driver minimum for 3 years for any defects developed during the period.

S&F LED building security light 1 x 20W housing made out of pressure die-cast aluminium alloy with toughned glass, IP 66 protection working on 240 volts, 50 Hz, consisting of reflecting lamps wired with appropriate driver PF> 0.98 having overvoltage protection upto 440 volt, surge protection level > 10 KV, thermal short circuit protection THD< 10% made up of long life LED chip (SMD) in modular with Ra< 70, and LED lumen efficiency > 140 lumen per watt, beam angle along the drive way, 120 degree, beam angle across the drive way, 80 degree luminaire efficiency> 120 luminous /watt power LED should be of more than 01 watt CCT should be between 5700° K- 6500 K including fixing on existing bracket including making necessary electric connection with 1.5 Sqmm, 3 core, PVC insulated copper conductor cable 1100 Volt grade complete all as specified and as directed. Make :– Shakti Fixtures Pvt Ltd, Cat Part No. SZPSLPM020 / Havells, Cat Part No. ENDURAPEARLS20W or equivalent of others make as specified. Note: The firm has to give warranty for fitting including driver minimum for 3 years for any defects developed during the period.

S&F service cable 1100 Volts grade heavy duty cable PVC insulated stranded aluminium conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended with insulating hanger not more than 1 mtr apart including 4 mm dia suspension wire alongwith 16 Sqmm twin core flat cable all as specified and directed.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. (Earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate. connected by 4 mm GI wire as earth lead by means of brass nuts and bolt, thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size PCC 1:2:4 Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade GI pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing wire to panel, including testing on completion complete all as specified and directed. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick reinforced with XPM weighing not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

PRAMOD KUMAR

Panwar Electrical