Repair work in Creche

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.For fixed portion:Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4 mm wide aperture'.

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre (Including for all heights, necessary support and scaffolding charges etc)

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.One coat (Asian Royale Shyne/Berger Silky Gamour)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work

12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand)

Structural steel work in single section, fixed with or without connecting plate, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing SS curtain rods with two brackets fixed with screws and wooden plugs etc. wherever necessary complete. 25 mm diameter.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL antitermite treatment (excluding the cost of chemical emulsion) :

Along external wall/plinth protection where the apron is not provided using chemical emulsion@ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete along with treating backfilled earth with chemical emulsion & making good the same: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole & applying putty on top etc.: 12mm dia holes shall be drilled as close as possible to the plinth wall @300mm interval, deep enough to reach the soil below and chemical emulsion pumped into these holes to soak the soil below @ 2.25 litre per linear meter.With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole & applying putty on top :With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Supplying chemical emulsion conforming to relevant Indian standard in sealed containers including delivery as specified. Chlopyriphos conforming to relevant IS 8944/Lindane emulsifiable conforming to IS 632 concentrate of 20%.in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%. Note: Chemical shall be kept in the custody of Engineer-in-charge or his authorized representatives and will be issued for use to meet the day's requirement. Empty Conntainers after washing & concentrated chemicals left unused at the end of day's work shall be returned to EIC or his authorized representative.

LAXMI NARAYAN ENTERPRISES (BID ID -3244287)