WELCOME MAINT TO OFFRS MD ACCN AND REPAIRS/MAINT OF JOINERY, PLUMBING, ROOFING, FLOORING ETC TO MD OFFRS ACCN AND JCOS AND ORS ACCN AND OTM ACCN AT ZONE C AREA AT KANCHRAPARA UNDER GE BARRACKPORE

Amount

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlars facing dressed stonework & precast concrete articles complete all as specified and directed.

Taking down cement plaster of any description on brick or stone or concrete surface of wall etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Demolition of cement concrete (unreinforcement) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of cement concrete (reinforcement) in ground floor not exceeding 15 cm thickness (below or above ground level) , reinfocement cut as required to facilate demolition all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness including cover fillet all as specified and directed.

Dismantling of asbestos cement (corrugated, semi-corrugated etc.) sheets in roof coverings complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering etc all as specified and directed.

Dismantling timber boarding, any description, fixed with nails complete all as specified and directed.

Dismantling timber scantlings (framed work) 40 sq.cm and over in section, in any position complete all as specified and directed.

Dismantling timber (framed work) in fillets, rails posts, rafters, purlins etc under 40 Sqcm in section complete all as specified and directed.

Taking down chowkats or frame (without taking off shutter from the frames) not exceeding 1.50 Sqm each complete all as specified and directed.

Taking down chowkats or frame (without taking off shutter from the frames) exceeding 1.50 Sqm and not exceeding 4.00 Sqm each complete all as specified and directed.

Taking down of shutter of any description not exceeding 1 sqm each all as specified and directed.

Taking down of shutter of any description exceeding 1 Sqm and not exceeding 2.0 Sqm each all as specified and directed.

Taking down of shutters of any description not exceeding 1 Sqm and refixing in same opening after easing and adjusting all as specified and directed.

Taking down of shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm and refixing in same opening after easing and adjusting all as specified and directed.

M&L for resecuring or easing & adjusting without taking down of shutters of any description exceeding 1 sqm and not exceeding 2 Sqm each complete all as specified and as directed

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6) complete all as specified and directed.

M&L for brickwork with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed.

M&L for 40 mm thick PCC (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in floor finished, even & fair with using extra cement all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate), as in hard standing/plinth protection etc finishing cement concrete surfaces even & smooth without using extra cement complete all as specified and directed.

M&L for PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in surface channel and drains etc complete all as specified and directed.

M&L for RCC (nominal mix) (1:2:4) type B1 (using 20mm crushed stone graded aggregate) used as in slab supported on walls, beams and columns in floors, roofs, landing, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc for flat, rough finish surface of concrete complete all as specified and directed.

M&L for TMT bars 6mm to 8mm dia and over cut to length bent to shape as required including cranking, bending spirally for hooping for columns (as in stirrups), hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for TMT bars 10 mm dia and over cut to length bent to shape as required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for non skid (joint free) ceramic coloured (colour & shade as approved by GE) tiles of 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in colour cement to match over and including 15mm thick Screed bed or beading layer of cement mortar (1:6) for laying floor finishes complete all as specified and directed.

M&L for non skid (joint free) ceramic coloured (colour & shade as approved by GE) tiles of 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in colour cement to match over and including 15mm thick Screed bed or beading layer of cement mortar (1:6) for laying floor finishes complete all as specified and directed.

All as per Item No.29.00 here-in-before but in skirting/dado, wall/vertical surfaces etc over and including a backing coat of 10mm thick plaster in cement mortar (1:4) complete all as specified and directed.

S&F for vitrified (joint free) ceramic coloured tiles (colour & shade as approved by GE) of 9 to 10mm thick not exceeding 0.36Sqm area of each tiles as in floor, set and jointed in neat cement slurry and pointed in colour cement with pigment to match the colour of tiles over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and directed.

All as per Item No.31.00 here-in-before but in skirting over and including a backing coat of 10mm thick rendering in cement mortar (1:4) complete all as specified and directed.

M&L for 20 mm thick granite slab (of any type) machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the of granite stone including grinding and polishing over and including 15 mm thick screed bed of cement mortar (1:6) including dismantling old granite, bedding complete all as specified and directed.

M&L for 20mm thick granite (of any type) tiles machine cut, in wall/skirting/dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including a backing coat of 10mm thick bedding in cement mortar (1:4) including dismantling of old granite, bedding complete all as specified and directed.

S&F for glazed ceramic coloured wall tiles 300mm x 450mm x 7mm thick (colour & shade as approved by GE) set and jointed neat cement slurry and pointed in colour cement to match over and including 10 mm thick plaster of cement mortar (1:4) all as specified and directed.

S&F for false ceiling with exposed metal (PPGI) framework/ “Tee” Grid providing and fixing of suspended Tee gird false ceiling using “T” Gird System – powder coated GI (PPGI) exposed grid false ceiling suspension system in grid size 600mm x 600mm with main runner 32 x 24mm x 0.3mm thick, cross tee 26mm x 24mm x 0.3mm thick and wall angle 24mm x 24mm x 0.40mm thick using 4mm thick non asbestos fibre cement board (oceanic) of size 595 x 595mm, an asbestos Free fibre cement board manufacture using high Pressure System Curing technology. T gird Framing is suspended using 4mm GI/MS bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip, also providing provisions for light fixtures, air conditioning diffusers and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last hanger at the end of each main runner should not be placed at not more that 300mm from the adjacent wall. 1220mm/600mm Cross Tee to be interlocked between main runners @ 600mm c/c, so as to from 600mm x 600mm or 1200mm x 600mm grid, confirming IS 14862 & type B category III of ISO 8336, tested as per AS 1530 part – 3 & B. S- 476 part 4,5,6,7 & 8 should be placed in Gird module to form all complete as per the drawing & directions of Engineer-in-Charge.

S&F for 4mm thick fibre asbestos cement plain building boards, fixed to timber framework with screws complete all as specified and directed.

M&L for 6mm thick fibre asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc. fixed with 'L' or 'J' type hooks complete all as specified and directed.

M&L for 6mm thick fibre asbestos cement two pieces adjustable serrated ridge for corrugated or semi- corrugated sheets fixed with 'L' or 'J' type hooks complete all as specified and directed.

S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of 0.50mm thick of any colour as approved by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F for pre-painted galvalume aluminium zinc coating GI based plain steel sheet of 0.50mm thick of any colour as approved by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F for 20mm thick second class hard wood boarding in roofs planed both sides and joints are chamfered one side and the boarding is matched complete all as specified and directed.

M&L for second class hard wood in scantling, clean swan as in frame work, fixed with nails complete all as specified and directed.

M&L for second class hard wood in fillets, square, rectangular or triangular in section, clean swan, fixed with nails, sectional area exceeding 3 sqcm but not exceeding 6 Sqcm complete all as specified and directed.

M&L for second class hard wood in fillets, square, rectangular or triangular in section, clean swan, fixed with nails, sectional area exceeding 6 sqcm but not exceeding 13 Sqcm complete all as specified and directed.

S&F for second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints of second class hard wood etc complete all as specified and directed.

S&F for pressed steel frames for door (factory made) of size 165mm X 60mm of 1.25mm thick with one or more rebates including necessary fittings lugs, hinges, lock strike plate, etc including filling of concrete (1:3:6) type C-0 (using 12.50 mm graded aggregate) back of chowkhats and applying two coats of synthetic enamel paint over and including a coat of red oxide primer all as specified and directed.

S&F for pressed steel frames for door (factory made) of size 105mm X 60mm of 1.25mm thick with one or more rebates including necessary fittings lugs, hinges, lock strike plate, etc including filling of concrete (1:3:6) type C-0 (using 12.50 mm graded aggregate) back of chowkhats and applying two coats of synthetic enamel paint over and including a coat of red oxide primer all as specified and directed.

S&F for 35mm thick (factory made) plain, second class hard wood, framed, panelled shutters (three panels) with lock rails and panel of 12 mm veneered particle board with commercial veneering on both faces (BWR type), the size of rail and stile as per IS-1003 (Part-I) (larger size to be provided) klin seasoned and chemically pressure treated fitted to chowkats complete all as specified and directed.

S&F for 35mm thick second class hard wood glazed/ gauge & skeleton shutters (factory made), open rebated & prepared to receive glass, gauge etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitered beads for securing glass etc. sizes of members of shutters as specified in SSR part-I, section-8, clause 8.24 (a) (larger size to be provided) complete all as specified and directed.

S&F for steel windows (factory made) with side hung shutters (glazed/gauged) including box type hinges with steel handle, frame, steel peg stay, complete without glazing bars, dovetailed or welded to receive wire mesh including one coat of red oxide zinc chrome primer at factory complete all as specified and directed.

S&F for steel windows (factory made) with side hung shutters (glazed/gauged) including box type hinges with steel handle, frame, steel peg stay, complete with glazing bars, dovetailed or welded to receive glass, including one coat of red oxide zinc chrome primer at factory complete all as specified and directed.

S&F for steel ventilators (factory made) with top hung shutters including box type hinges with steel handle, frame, steel peg stay, complete, dovetailed or welded to receive wire mesh/glass including one coat of red oxide zinc chrome primer at factory complete all as specified and directed

S&F for anodised aluminum frame for doors , windows, ventilators with one or more rebates (sliding & fixed type) including joining cleat for fixing etc complete all as specified and directed

S&F for anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed.

S&F for anodised aluminium window/ventilators shutters, sliding/fixed type without sash bar, aluminum section weighing 0.55 Kg/m, including necessary joining cleat, glazing clips, rubber neoprene packing, handle, hinges, peg stay, anodised aluminium snap beading, screws etc complete locking arrangement, roller all as specified and directed.

S&F for 4.0 mm thick sheet glass tinted fixed with beads complete area exceeding 0.50 Sqm each pane complete all as specified and directed.

S&F for 5.5mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares not exceeding 0.50 sqm each pane all as specified and directed.

S&F for stainless steel wire cloth, 0.36 mm nominal dia of wire & average width of aperture 1.40mm & fixed with stainless steel wire staple complete as in repair all as specified and directed.

S&F for stainless steel wire cloth, 0.36 mm nominal dia of wire & average width of aperture 1.40mm & fixed with stainless steel wire staple complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) used as in brick, concrete wall for fixing of hold fast including necessary form work complete all as specified and directed.

Hacking out old broken glass (any thickness size quality or description) from wooden or steel frame, glazed with putty or fixed with beads etc complete all as specified and as directed.

S&F for 3.0mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares not exceeding 0.50 sqm each pane complete all as specified and directed.

S&F for 4mm thick figured glass, pin head type and glazing with oil putty in square not exceeding 0.5 sqm each pane all as specified and directed.

S&F for 300 mm aluminum alloy, anodised , sliding door bolt with hasp and staple (bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed complete all as specified and directed.

S&F for 150 mm long aluminium anodised extruded alloy handle fabricated type complete all as specified and directed.

S&F for 150 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for 100 mm long aluminium anodised extruded alloy handle fabricated type complete all as specified and directed.

S&F for 100 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for 100 mm long stainless steel butt hinges, medium weight complete all as specified and directed.

S&F for 300 mm aluminum alloy, anodised , sliding door bolt with hasp and staple (bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed complete as in repair all as specified and directed.

S&F for 150 mm long aluminium anodised extruded alloy handle fabricated type complete as in repair all as specified and directed.

S&F for 150 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete as in repair all as specified and directed.

S&F for 100 mm long stainless steel butt hinges, medium weight complete as in repair all as specified and directed.

S&F for 100 mm long aluminium anodised extruded alloy handle fabricated type complete as in repair all as specified and directed.

S&F for 100 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete as in repair all as specified and directed.

S&F for 18/19 mm thick veneered finish prelaminated particle board fix in cupboard shelves & shutter interior grade, prelaminated in one side with decorative choice lamination solid core medium density general purposes, and other side white lamination fixed with screw including teakwood lipping complete as in repair all as specified and directed.

S&F for curtain rail, chromium plated with bracket (fancy type), end bulbs (fancy type), stops, rollers etc complete as in repair all as specified and directed.

S&F for factory made solid PVC door frame of size 50mm X 47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube as per specification and drawing complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified and directed.

S&F for 75 mm long stainless steel butt hinges, medium weight complete as in repair all as specified and directed.

S&F for mild steel hold fast/wind tie made out of flat iron including tarring or coal tar black paint and with drilling necessary holes etc conforming to Fe 410-0 or Fe 310-0 all as specified and as directed.

S&F for aluminium extuded body door closer hydraulically regulated designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 85 Kg as complete fixed in repairs all as specified and directed.

S&F for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel (heavy duty) complete as in repair all as specified and directed.

Taking up or down steel tubings & connections including cleaning for refixing or removal from site for 15 mm bore pipes complete all as specified and directed.

Refixing old steel tubings & connections in new or old position (wall, ceiling, floor etc.) for 15mm bore pipes with new fittings etc complete all as specified and as directed. (Note : Pipe shall be obtained from Item No 85.00 above)

S&F for 15mm dia tubes (medium grade) galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors, wall etc (surface or concealed type) complete all as specified and directed.

Taking up or down steel tubings & connections including cleaning for refixing or removal from site for 20 mm bore pipes complete all as specified and directed.

Refixing old steel tubings & connections in new or old position (wall, ceiling, floor etc.) for 20mm bore pipes with new fittings etc complete all as specified and as directed. (Note : Pipe shall be obtained from Item No 88.00 above)

S&F for 20mm dia tubes (medium grade) galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors, wall etc (surface or concealed type) complete all as specified and directed.

M&L for cutting chases, in brick wall and making good to facing where required and pointing in cement mortar (1:3), to ends or edges of landing, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting exceeding 10cm but not exceeding 20 cm girth complete all as specifid and directed.

S&F for PVC water closet seat, white/black colour as required, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete as in repair all as specified and directed.

S&F for 10 Ltrs capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete with all internal accessories and fixed to wall and jam nuts on both sides, PVC flush pipe 32mm dia 90cm long fixed properly to inlet of WC and making good to disturbed surfaces of wall or floor complete as in repair all as specified and directed.

S&F for 20mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe & fixed (minimum weight 210 gms) complete as in repairs all as specified and directed.

S&F for PVC Cover/ Lid (ISI Marked) for PVC water tank of 500 Ltr/1000Ltr capacity as in repair complete all as directed.

M&L for preparation of plastered surfaces 1.5mm thick and applying polymer modified bituminous elastomeric water proof coating as per manufacturer's instructions for sunken portion of toilet, bathroom and similar portions at any place/location and in any condition all as specified and directed by Engineer-in-Charge (Make : PIDILITE INDUSTRIES LTD (Dr FIXIT proof coat) or equivalent of IWL/TEXSA /STP as approved). The work should have be carried out by Authorised Applicator of Manufacturer's as approved by GE. (NOTE: The rate includes for preparation of surfaces treatment and sealing of all joints, cracks, corner and junction of pipes etc. and ponding test complete all as directed by Engr-in-Charge)

M&L for PCC (1:5:10) type E2 (using 40mm graded brick coarse aggregate) as in filling sunken floor of bathroom/toilets etc complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in sub-floor with WPC @ 2% by weight of cement all as specified . (Note : WPC shall be measured and paid separately).

S&F for vitreous china wash down water closet pan (pedestal pattern) white with P or S trap (excluding flushing cistern & flush pipe) including connection to trap & to flushing pipe, anti-syphonage pipe & seat cover etc. complete as in repair including making good to floor all as specified and directed.

S&F for vitreous china squatting pan 'Orissa' pattern, size 580x440mm white, with integral foot rests with P or S trap (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe etc complete including making good to floors with PCC bedding (1:5:10) type E2 using 40mm nominal brick ballast and connection to trap with cement mortar all as specified, and making good to floor including demolition of PCC / lime concrete bedding existing pan complete as in repairs all as specified and directed.

S&F for vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern but including flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2) securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete as in repair all as specified and directed.

S&F for EWC of size 72cmX41cmX79cm cm (pedestal pattern), white (including fixing bolts, flushing cistern and flush pipe) complete as in repair all as specified and directed. (Make:Hindware, Cat No.92026 for EWC with seat cover and Cat No.92126 for cistern with lid with fittings rate consider as a complete set or equivalent of Parryware/ Cera as approved)

S&F for sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete as in repair all as specified and directed.

S&F for sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete as in repair all as specified and directed.

S&F for 32mm dia waste fittings, brass chromium plated for glazed ware sinks, basins etc. with long screwed shanks & fly nuts, flanged end bedded in red lead cement & other end fixed complete as in repair all as specified and directed.

S&F for 32mm bore low density polyethylene pipes (LDPE) of pressure rating 6kgf/cm2 fixed complete to wall or in floors etc. as in outlet pipe for WHB, urinal etc. complete as in repair all as specified and directed.

S&F for vitreous china wash basin, white, flat back, size 550 X 400mm, excluding taps, chain and plug and porcelain stopper but including waste pipe, brackets and cutting for and pinning in ends of brackets or erecting stand complete as in repair all as specified and directed.

S&F for 15 mm bore stop valve, fancy type chromium plated with long shank and cup (concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete as in repair all as specified and directed.

S&F for 125mm size brass chromium plated shower roses with arms, swivel joints, including fixing to steel pipe or union complete as in repair all as specified and directed.

S&F for 15 mm dia angular stop valve cast copper alloy, chromium plated, fancy type, screwed down high pressure with wall flange complete as in repairs all as specified and directed .

S&F for PVC connection pipe 15 mm size with PTMT nuts of length 600 mm complete as in repair all as specified and as directed.

S&F for 15mm dia pillar taps, cast copper alloy with capstan heads, chromium plated, fancy type, screwed down high pressure, with letter 'HOT' or 'COLD' with long screwed shanks & fly nuts, screwed for iron pipes complete as in repair all as specified and directed.

S&F for 20mm dia gun metal gate valves with iron wheel head screwed both ends for iron pipes or for unions pipes, fixed as in repairs all as specified and directed.

S&F for 50mm bore high density polyethylene pipes (HDPE) of pressure rating 6kgf/cm2 fixed complete to wall, ceiling or in floors etc. as in outlet pipe for WHB, urinal etc. complete as in repair all as specified and directed.

S&F for 15mm dia bib taps, cast copper alloy, fancy type, chromium plated with flange complete as in repairs all as specified and directed.

S&F for health faucet fixed to EWC with 1mtr long easy flexible tube and wall hook complete as in repair all as specified and directed. (Make: Jaquar Cat No.ALD-565 or equivalent of Marc/Kohler as approved)

S&F for brass CP wall mixer 15mm dia for mixing hot & cold water screwed down for iron pipe and fixed complete as in repair all as specified and directed.

S&F for CP wash basin mixer of 15 mm dia for mixing hot & cold water screw down for iron pipe including necessary connection pipe from stop cock complete as in repair all as specified and directed.

S&F for 125 mm long aluminium anodised hasp & staple safety type including hinge pin, bolt to hinge plate etc complete as in repair all as specified and directed.

S&F for PVC bathroom cabinet with mirror 35X45cm complete as in repair all as specified and directed.

S&F for 200mm dia brass chromium plated tubular towel ring complete as in repair all as specified and directed.

S&F for soap dish, chromium plated complete as in repair all as specified and directed.

S&F for chromium plated toilet paper holder with stainless steel flap fixed to walls with chromium plated brass screw complete as in repairs all as specified and directed. (Make: Jaquar Cat No.AQN-7753 or equivalent of Marc/Kohler as approved)

S&F for glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete as in repair and all as specified and directed.

S&F for stainless steel kitchen rack of size 750mmX600mmX250mm, fabricated type with all fixings accessories complete including taking down old stainless steel rack all as specified & directed.

S&F for 100 mm long aluminium anodised hasp & staple safety type including hinge pin, bolt to hinge plate etc complete as in repair all as specified and directed.

S&F for ball catches with 8mm dia steel ball and brass body and striking plate including letting in and fixed complete as in repair all as specified and directed.

S&F for steel rolling shutter (thickness of laths 1.00mm) without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated complete push pull or manual type as in repair all as specified and directed.

S&F for mild steel safety lever locks with four levers for rolling shutters complete as in repair all as specified .

S&F for ball bearing for rolling shutter complete as in repair all as specified and directed.

S&F for 100mm bore sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints, fixed in wall with clamps and cement joints complete as in repair all as specified and directed.

S&F for 100 mm dia cast Iron bends (any radius) diminishing piece or tapers (larger bore measured) fixed with oval access door complete as in repair all as specified and directed.

S&F for 100 mm dia cast Iron bends (any radius) diminishing piece or tapers (larger bore measured) complete as in repair all as specified and directed.

S&F for 100mm dia CI branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches fitted with oval access door complete as in repair all as specified and directed.

S&F for 75mm bore sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints, fixed in wall with clamps and cement joints complete as in repair all as specified and directed.

S&F for 75 mm dia cast Iron bends (any radius) diminishing piece or tapers (larger bore measured) complete as in repair all as specified and directed.

S&F for 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches as in floor after dismantling of old PVC/AC pipe complete all as specified and directed.

S&F for 110 mm bore PVC (SWR) bends any radius provided with access door complete as in repair all as specified and directed.

S&F for 110 mm bore PVC (SWR) bends any radius complete as in repair all as specified and directed.

S&F for 110mm bore PVC (SWR) branch pieces, single (single Y) equal or unequal provided with access door complete as in repair all as specified and directed.

S&F for salt glazed stone ware gully trap of size 150mmX150mm square or round moulded type 'P' complete all as specified and directed.

M&L for 100mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F for brass chromium plated tubular towel rail, 20mm dia, D-type, 60cm long between flanges complete as in repairs all as specified and directed.

S&F for 500 Ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) multi layer (three layer) hoisted and fixed in position with cover of tank with its locking arrangement, making hole for inlet, outlet and overflow connection including dismantling / taking down old PVC water tank, ball valve etc complete all as specified in SSR Part-I all as specified and directed.

S&F for 1000 Ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) multi layer (three layer) hoisted and fixed in position with cover of tank with its locking arrangement, making hole for inlet, outlet and overflow connection including dismantling / taking down old PVC water tank, ball valve etc complete all as specified in SSR Part-I all as specified and directed.

M&L for rendering 20 mm thick, 1st coat 10mm thick in cement mortar (1:6) & 2nd coat 10mm thick in cement mortar (1:4) with water proofing compound @ 2% by weight of cement, plastered surface shall be finished even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately, WPC shall be used in second coat only)

M&L for rendering 15mm thick in cement mortar (1:6) on fair face of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound, ISI marked complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar (1:3) on fair face of brick work or concrete surfaces, finished even and smooth without using extra cement on ceiling surface and chajja complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer after preparation of new wooden surfaces of any description over 10 cm girth or width complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer after preparation of new wooden surfaces of any description not exceeding 10 cm width or girth complete all as specified & directed.

M&L for applying two coats of synthetic enamel paint over and including a coat of red oxide primer after preparation of new steel surfaces of any description over 10cm width or girth complete all as specified and directed.

M&L for applying three coats of white wash on surface of wall including preparation of new plastered surface complete all as specified and directed.

M&L for applying two coats of distemper oil emulsion ver and including a coat alkali resistant primer after preparation of newly plastered surfaces of walls complete all as specified and directed.

M&L for applying two coats of oil emulsion distemper over and including one coat primer after applying 3mm thick wall care putty (as directed by GE) after preparation of newly plastered surfaces of walls complete all as specified and directed.

M&L for applying two coats of cement based paint over a coat of alkali resistance primer on newly plastered surface of walls including preparation of surface complete all as specified and directed.

M&L for applying two coats of cement based paint on old plastered surface of walls as directed by GE after complete removal of existing treatment complete all as specified and directed.

M&L for applying three coats of white wash on surface of ceiling including preparation of new plastered surface complete all as specified and directed.

M&L for applying one coat of distemper oil emulsion after preparation of old surfaces of walls, cornices etc by washing, rubbing down with wire brushing etc complete all as specified and directed.

M&L for applying two coats of oil bound distemper over a coat of chalk whiting primer over and including applying 3mm thick wall care putty (as directed by GE) after complete removal of existing treatment on old plastered surface of wall complete all as specified and directed.

M&L for applying one coat of white wash on old decorated wall surfaces after preparation of old plastered surfaces complete all as specified and directed.

M&L for one coat of white wash on ceiling surfaces after preparation of old plastered surfaces complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint after preparation of old painted wooden surfaces of any description, not otherwise described, over 10cm in width or girth complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint after preparation of old painted steel surfaces of any description, over 10cm in width or girth, not otherwise described complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description etc complete all as directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or forged into spikes; framed guard bars; barred iron doors; ladders, railings, framed brackets, walk ways, frame work of water tank and similar work conforming to Fe-290-0 Gde-E-165 complete all as specified and directed.

RUNJEN CONSTRUCTION

M/S PAUL CONSTRUCTION

MANOJ CONSTRUCTION

M/S. ARUP KUMAR DEY