Design, Engineering, Supply, Installation, Testing and commissioning of Non Clog type Centrifugal Pump Set for effluent with accessories and allied Electro-Mechanical and Instrumentation and SCADA work at MRF Company Pumping Station at Dahej III.

Name of Work: Design, Engineering, Supply, Installation, Testing and commissioning of

"Non Clog type Centrifugal Pump Set for effluent" with accessories and

allied Electro-Mechanical and Instrumentation and SCADA work at MRF

Company Pumping Station at Dahej III.

Item Description Qty Unit Rate W/O Amount W/O

1 MECHANICAL WORK 2 Set 799,518.02

Submersible Centrifugal Non Clog

Pump-Motor Set:-Supply, installation,

testing & commissioning of effluent

submersible, non clog type suitable

for working on three phase, 50 Hz ±

3%, 415 V ± 10%, AC supply,

RPM synchronous speed with 3 core

flat copper cable from pump to starter

panel with cable end terminations, all

supports, clamps, pipe fittings along

with mechanical seal, bearing bush,

strainer etc. complete set & following

M.O.C: Casing: CI, Impeller: SS CF8M,

Wearing ring & Bearing bush: Bronze,

TC mechanical seal, CS / SS bearing,

SS shaft with sleeve, SS strainer & MS

Pump Capacity: 338 m3 / hr.

Motor Rating: 42 kW min. (or higher

rating as per pump manufacturer

recommendation)

Starting method: DOL / SD / VFD

(or higher rating as per pump

recommendation)Selection of motor

kw rating if not available in this

rating, next higher rating will be

2 Design, Engineering, procurement, 2 Nos. 66,029.76

Installation, Testing and

commissioning of required size

double flanged Dual Plate Check Valve

(DPCV) - (PN 1.6) - 350 mm dia (At

Pump Discharge) Flanged Dual Plate

Check Valve (NRV) conforming to API

Signature of Contractor Executive Engineer (M&E)

594 / 598 PN 1.6 with Cast Steel body,

with SS 410 hinge ring and wearing

ring of CF8 all necessary hardwares,

complete as per data-sheet &

specification. Size : 350 mm dia( PN

1.6) flanges machined faced and

drilled to IS : 1538 / 1976 Part-IV/VI.

Hydraulic tests certificate & certificate

of material of construction of parts

shall be submitted before dispatch of

valves as per design with required

accessories, erection hardware,

necessary mounting supports etc.

complete. 350 mm dia for various

3 Supply, installation, testing & 2 Nos 13,453.20

commissioning of flange ends

Expansion Bellow as per EJMA

standards of overall length of

minimum 300 mm, designed for

mm axial compression and 5 mm axial

extension with tie rods etc. of

following MOC & pressure ratings.

MOC: Bellows: SA 240 Gr. 304;

Internal Sleeve: SA 240 Gr. 304;

Weldends: IS 2062 Gr. B; Flanges: IS

2062 Gr. B (Drilling as per IS 1538 / IS

6392 ) & Limit Rods & Nuts: CS - IS

1367. PN Rating 1.6, 350 mm Dia.

4 SITC of Cast Steel D/F Electric 2 Nos 930,800.00

Actuator operated Sluice Valve of

following size as per API-

600/598,Class 150 with Electric

Actuator with integral starter & IP-68

enclosure, body, bonnet and wedge of

Cat Steel Gr. WCB with Body & Seat

ring of ASTM A 216 Gr CF8M, spindle

of SS 410, flanges drilled to ANSI B

16.5 of following diameter along with

all other necessary hot dipped

galvanised hardwares, bolts, nuts &

washers, gaskets including all taxes,

insurance, transportation, freight

charges, Inspection Charges, loading

unloading, conveyance to pump

house, stacking, security with

required plain cement concrete (PCC)

support for Valves etc. within pump

house for fixing valve etc. complete as

per Specification and IS.

Signature of Contractor Executive Engineer (M&E)

Size : Dia. 350 mm

5 Provide and supply CI Temper Proof 1 Nos 49,161.75

Air Valves with SS 304 Float Gun

Metal Nozzle of approved make and

quality of following dia of 1.6 PN

rating given rate including all taxes,

insurance, transportation, freight

charges, inspection charges, loading

and unloading conveyance to

departmental store/site Etc.with

Isolating Sluice Valve.

Size : 350 mm NB

6 SITC of suitable size of above pipes of 100 Kg 58.58

flanged end type fabricated DI/CI

Specials like tee, bend, duck foot bend,

tapper, distance pipe piece, blank

flange, dismantling joint, bolts, nuts,

washers, rubber packing etc. nut bolts

etc for delivery header, rising main

and suitable for above pumps as per

actual site conditions & requirement

qty. of specials mentioned as per

design requirement with required

accessories, erection hardware,

necessary mounting supports etc.

7 Supplying and fixing Steel chequered 20 Sq. Mtr 5,780.23

plates having 12 mm thickness, duly

painted with two coats of black Japan

colour. (Average Wt 200.3 kg /

8 Supply, cutting, welding, installation, 8 Rmt 1,456.42

connection with main header, testing

and commissioning Making of Flanged

joint to flanged DI/CI pipes of all

classes/ Special etc. including all

taxes, insurance, transportation,

freight charges, inspection charges,

loading and unloading conveyance to

departmental store/site Etc

Size: 350 mm dia.

9 Single Girder EOT CraneSupply, 1 Set 511,312.50

installation, testing & commissioning

single girder type fully electrically

operated EOT crane with electrically

operated hoist, class II duty, geared

travelling trolley with seven meter lift

complete with long travel rail track

(40 mm sq. bar), moving or cross

Signature of Contractor Executive Engineer (M&E)

girder, all three motions electrically

operated by suitable rating motor IP

54, control panel & down pendant

control block, brake, safety device,

cables form motor to starter panel &

other required accessories & tested as

per IS Specifications.Capacity- 2 T,

Span- 6-9 Mtr, Long Travel- 12 Mtr,

10 SITC Chain Pulley block of 2 ton 1 Nos 17,574.00

capacity, lift as per site condition with

gantry girder, erection hardware,

necessary mounting supports etc

complete. make as per annexure.

11 DEWATERING PUMP 2 Nos 147,811.48

Supply, erection, testing and

commissioning of non clog

submersible Drain Pump with CI

casing & CF8M impeller, including

necessary accessories and hardwares,

etc., 15m cable for motor to starter

panel, suitable for 3Phase, 415 V,

Hz AC supply and min. 2.2 kW motor,

Switch-Starter panel with suitable

inter lock for winding protection, min.

10 m long required size cable to

supply power to control panel from

nearby power source, moisture

controller along with level switches

for dry run protection for auto stop

facilities, cable termination junction

box of required terminal size,

supporting arrangement for pump

and other required accessories,

Capacity : 10 - 15 m3 / hr.

( to be installed in dry well drain pit.)

12 PORTABLE DEWATERING PUMP / 1 Nos 194,690.63

Supply and testing of Submersible non

clog Portable Dewatering Pump set

with C.I. casing & CF8M impeller, 25 m

flexible PVC delivery hose pipe of

pump delivery size, rated for 6.0 kg /

cm2 pressure, 15 mtr SS lifting chain,

20m pair of cable for motor to starter

panel, suitable for 3Phase, 415 V,

Hz AC supply and min. 5.5 kW motor,

min. 10 m long required size cable to

supply power to control panel from

Signature of Contractor Executive Engineer (M&E)

nearby power source, Switch-Starter

panel with suitable inter lock for

winding protection, moisture

controller & dry run protection auto

stop facilities, SS/CI pump stool and

other required accessories for wet

Capacity : 50 m3 / hr.

Motor Rating: Mini. 5.5 kw

13 MISCELLANEOUS: 800 Kg 65.49

Providing, Supply of Structure Steel at

site of work with freight, loading,

unloading carting, etc. including all

taxes and duties complete such as

joints, channels, angles, plates, iron

rails, ISA/ISMC/ISMB/MS flat, plate

(below 10mm thickness) etc.

required for support structure of

Elecrto-Mechanical equipments etc.

for support on floor / wall / beam /

brackets etc. as per tender and IS.

14 Labour Charges for lowering, laying, 1 MT 11,478.65

Fixing with fabrication various size

section of MS such as joints, channels,

angles, plates, iron rails,

ISA/ISMC/ISMB/MS flat, plate etc

Complete with two coats of red oxide

and two coats of approved colour

shade of epoxy paint as per relevant IS

and as per specification.

15 Tools as per Annexure (M) and as 1 Lot 250,000.00

recommended by manufacturer as

approved by engineer in Charge.

16 ELECTRICAL WORK 1 Nos 37,601.29

TPN MCCB (For LT Service Obtaining

SITC of 200 A TPN microprocessor

MCCB with O/L, S/C & E/F protection

with Extended rotary handle,

Terminal spreader, Auxiliary change

over & Trip contact, with Outdoor

Enclosure with canopy 2mm thick

Single/double door & Wall mounted/

stand mounted as per site

requirement (with incoming &

outgoing cable entry at bottom )with

Cable end boxes with RYB indicating

lamp, Digital voltmeter, VSS, ON,OFF

& Trip indicating lamp etc as per

Signature of Contractor Executive Engineer (M&E)

Power supply company requirements

& location. Including all civil works for

fixing of panel on wall.

(Wall mounted at Location as per PSC

17 LV APFC PANEL 1 Set 189,950.70

Supply, installation, testing &

commissioning LV APFC panel

consisting of required capacitor banks

for continuous duty to improve P.F.

0.85 to 0.99 in required steps

enclosed in dust & vermin proof

compartment, indoor type, fabricated

from CRCA sheet steel with minimum

thickness of 3 mm for base frame /

channel / gland plates, 2.0 mm for

load bearing members / doors &

mm for internal partitions, minimum

degree of protection - IP 42, busbar

chamber, required size of Al bus bar /

terminals, minimum 10 stage APFC

relay, metering, indicating lamps,

push buttons complete as per IS:

16636-2017 with latest amendment &

detailed technical specification and

data sheet as under

Above 50 & up to 100 KVAR: APFC

panel consisting following items.

a) 250 A, 50 kA for 1sec. TP, TM based

MCCB with spreader terminals &

b) 0-250 A range analogue ammeter

of 96 x 96 mm size with selector

c) 3nos. 250 / 5A, 10 VA CL-1.0 cast

resin type current transformer

d) Suitable rating of MCCB / MCB &

Contactors for each capacitor bank

e) Suitable rating APP type capacitor

banks (vacuum impregnated with

non-PCB / non toxic oil, internally

delta connected with built in internal

fuses complete with discharge

resistances & terminal cover) of

approved make in required steps with

well suited detuned reactor is placed

in series with each capacitor step. (

e.g. 100 KVAR capacity will be

provided in steps of 2 nos x 5 KVAR,

nos x 10KVAR, 2 nos x 15 KVAR &

Signature of Contractor Executive Engineer (M&E)

f) Enclosre dimensions: 2100 (H) x

18 Design, Supply, Installation, Testing 1 Nos 344,504.94

and Commissioning of Power cum

Motor Control Centre of 200 A,

TPN, Power Cum Motor Control

Centre (PCC) cubical having depth not

less than 750 mm throughout the

required length & detachable,

fabricated from 2 mm CRCA sheet

steel, free standing, floor mounted,

compartmentalized, extensible, dust

and vermin proof enclosure, duly

painted provided with required rating

switch gears and shall be complete

with (a) required size of TPN

Electrolyte 100 A Copper bus bar

having cross section not less than

Amp per 1.0 Sq. MM, (b) 3 Nos. -

Amp capacity of 4 pole-

microprocessor based MCCB with

computer interface (2 Nos. for

incomer + 1 No. as Bus Coupler) (c)

Nos. - 100 Amp capacity of 4 pole -

microprocessor based MCCB

computer interface - All release of all

MCCB should have in built power

meter/ analyser having, 3 phase, V,

KW, I, KVA, KVAh, KVArh, PF,

Frequency, harmonic analysis up to

30th harmonic and last ten faults

history.with computer interface

facility and all other required

protection etc., complete. ,The PCC

shall be supplied as per detailed

specifications & single line diagram

(SLD) complete and the instruction of

Engineer In charge.

19 Microprocessor Based LV Variable 2 Nos 111,862.55

Frequency Drive

Supply, installation, testing &

commissioning of 415 V Fully

automatic microprocessor based

Variable Frequency drive for pump

control application as per general

specification as under:

The VFD unit shall have modular

construction, 6 Pulse Bridge rectifier,

speed control by means of sensor less

Signature of Contractor Executive Engineer (M&E)

vector control (open loop), high

torque at low frequencies, locking at

high and low frequency settings, In-

built PID control, frequency accuracy

of ± 0.1 % (min), frequency resolution

of ± 0.1 Hz (min), protections against;

a) overload (motor and drive), b)

short circuit, c) ground fault, d) input

/ output phase loss (open circuit), e)

stalling, f) input / output

undervoltage (momentary power loss

restart), g) input / output overvoltage,

h) over-frequency, i) Input surge, j)

over temperature of heatsink, k) loss

of remote speed signal etc. The VFD

shall also have user friendly

programming software & it shall be

capable of at least two level

parameter setting with password lock

for critical parameters, programming

for I/Os, speed search function, copy

parameters (upload / download) to

other identical unit, tuning to energy

saving mode (maximum efficiency),

event / fault recording (last 5 faults in

non-volatile memory) & RS

communication port (MODBUS RTU

protocol) with required software. for

20 SITC of Lighting Distribution Board 2 Nos. 20,998.91

(LDB) as under:

SITC of 3 Phase 4 Wire 4P, double

door Prewired LDB each for Indoor

Lighting & Outdoor Lighting Suitable

Incoming: 200A FP, ELMCB (30mA)

Outgoing: 63A SP MCB (9 nos.) & 63A

SP MCB (9 nos.)

21 3 Phase 4 Wire TPN, 8 way Pre- 1 No. 8,876.89

wired- aux. Load for Auxiliary

accessories Load power supply (For

1no.EOT Crane at P.H., 1no.WR-DB at

P.H. maintenance floor, 1no. WR-DB at

P.H Pump Floor, 1no. WR-DB at LT

Room, 1 no. WR-DB at Inlet chamber

& rest spare) Incoming: 20A 4P, MCB

'C' Curve Outgoing: 8 nos. 20A 4P MCB

22 SITC of LCS pushbutton station ON & 4 Nos 2,384.61

OFF (E-stop) set complete with

Signature of Contractor Executive Engineer (M&E)

Enclosure, necessary mounting/ fixing

arrangement on wall / pipe support

etc. to be installed near motors for

remote operation, etc. as per IS and

specifications. (including structural

steel) (For 4 nos. for Pump )

23 SITC of Local Control Station with 4 Nos 2,736.09

pendant type Open_Stop_Close

pushbutton set and with Open, Close,

Trip & Local / Remote Indicating

Lamps complete with Enclosure,

necessary mounting/ fixing

arrangement on wall / pipe support

etc. to be installed near motors for

remote operation, etc. as per IS and

specifications (including structural

24 LOW VOLTAGE (LT) CABLES 180 Mtr 135.34

Supply, laying, testing and

commissioning of 1.1 kV,

A2XFY(X)/2XWY(X) XLPE insulated

(IS 7098) AL stranded conductor,

Extruded inner sheath cables as per

specification & IS. The cable when laid

outside the building shall be laid

underground in trench with brick &

sand protection/in DWC pipes as per

specified method and shall be laid in

prepared trench/ on cable tray when

laid inside the building.

SITC of 3.5C x 16 sq. mm. A2XFY(X)

25 3C x 16 sq. mm. A2XFY Cable 180 Mtr 90.90

26 4C x 10 sq. mm. A2XFY Cable 120 Mtr 97.97

27 4C x 16 sq. mm. A2XFY(X) Cable 120 Mtr 109.08

28 4C x 2.5 sq. mm. 2XWY/2XFY(X) Cable 50 Mtr 70.70

29 5C x 1.5 sq.mm. 2XWY(X) Cable 50 Mtr 150.00

30 12C x 1.5 sq.mm. 2XWY(X) Cable 50 Mtr 320.00

31 2C x 2.5 sq. mm. 2XWY(X) Cable 50 Mtr 49.00

32 Single core 95 sq. mm. PVC insulated 20 Mtr 919.10

circular unsheathed copper

conductor flexible Cable (For Power

supply Metering Panel to I/c MCCB

Signature of Contractor Executive Engineer (M&E)

33 CABLE END TERMINATION AND 32 Nos 161.60

SITC of Double compression Ni-

Plated brass cable glands and

crimping type Bimetallic lugs /

sockets with necessary tools and

equipments as specified in

specifications and IS. The glands and

lugs / sockets shall be suitable for

cable size and type mentioned below

& as per specifications.

1) Earthing the glands and armouring

with earthing clamp and jumper and

also connecting to common earth bar.

2) The job also includes, if necessary,

supply & fixing of extension busbar of

same material on MCCB or panel

board terminal / connector to connect

more than one no. of parallel cables or

to connect higher size cable to lower

size unit. The job also includes

earthing the glands and armour of the

cable with common earth bar or

flexible copper mesh.(Cable

termination qty. shall be as per site

3.5C x 16 sq. mm. A2XFY(X) Cable

34 Do as Above 3C x 16 sq. mm. A2XFY 32 Nos 158.57

35 Do as Above 4C x 10 sq. mm. A2XFY 32 Nos 129.28

36 Do as Above 4C x 16 sq. mm. 32 Nos 163.62

37 Do as Above 4C x 2.5 sq. mm. 20 Nos 93.93

2XWY/2XFY(X) Cable

38 Do as Above 5C x 1.5 sq.mm. 10 Nos 128.00

39 Do as Above 12C x 1.5 sq.mm. 10 Nos 218.00

40 Do as Above 2C x 2.5 sq. mm. 10 Nos 49.00

41 Single core 95 sq. mm. PVC insulated 10 Nos 213.11

circular unsheathed copper

conductor flexible Cable (For Power

supply Metering Panel to I/c MCCB

42 CABLE TRAY 80 Mtr 391.88

SITC of G.I. (Hot dip galvanised )

Signature of Contractor Executive Engineer (M&E)

Ladder type medium duty (2mm

thick) Cable Tray with necessary

bends, tees, reducers, covers and

clamps for fixing. All material shall be

Hot dip galvanised as per

Specification. And including all

accessories. 300 x 75 mm - Ladder

43 150 x 50 mm - Ladder type 200 Mtr 339.36

44 Cable Trench, Laying & Installation of 80 Mtr 55.55

Cable: Making cable trench in soft soil

of suitable width of 90cms deep for

laying cable, Sand cushioning and

brick protection on sides and on top

all over the run and back filling the

same and making the surface as

normal ground as per IS &

Specification. (For laying of LT cable

45 CHEMICAL EARTHING SYSTEM 4 Set 10,593.89

SITC of Maintenance free chemical

earthing (copper) with earthpit of

minimum bore size dia. 225mm Safe

Earthing Electrode consisting Pipe-in-

Pipe Technology as per IS-3043:1987

/Tech spec. made of corrosion free

Pipes having Outer pipe dia of

mm having 250 Micron copper

plating, Inner corrosion free Hot dip

galvanised (80 to 100 micron) pipe

dia of 26 mm with copper flat strip

type connection terminal 14mm dia

with constant ohmic value

surrounded by highly conductive

corrosion resistant chemical

compound with high charge

dissipation suitable for electrical

installation & of 3Mtr. length of Pipe

with two nos. 25Kg. bag of Back filling

compound.. (2nos for PLC earthing,

2nos for DG neutral earthing)

NOTE: Earthing Resistance value &

date shall be painted on the chamber

46 SITC of Maintenance free chemical 6 Set 7,095.25

earthing with earthpit of minimum

bore size dia. 225mm Safe Earthing

Electrode consisting Pipe-in-Pipe

Technology as per IS-3043:1987

Signature of Contractor Executive Engineer (M&E)

/Tech spec. made of corrosion free

Hot dip Galvanised (min 150 Microns)

Pipes having Outer pipe dia of

mm , Inner corrosion free Hot dip

galvanised (80 to 100 micron) pipe

dia of 26 mm with copper flat strip

type connection terminal 14mm dia

with constant ohmic value

surrounded by highly conductive

corrosion resistant chemical

compound with high charge

dissipation suitable for electrical

installation & 3Mtr. length of Pipe

with two nos. 25Kg. bag of Back filling

NOTE: Earthing Resistance value &

date shall be painted on the chamber

47 SITC of pipe type earthing having 150 6 Nos 368.65

cms long and 2.5cms dia. Galvanised

iron pipe with coupling and buch

buried in specially prepared earth pit

complete with necessary 8 SWG earth

48 SITC of 50mm(w) x 6mm(T) etc. sizes 276 Kg 77.77

as required, HOT dip galvanized GI

Strip including supply & fixing using

GI spacers, saddles when laid inside

the building and inclusive of

excavation & refilling of earth when

laid outside the building &

interconnection with earth pit & all

electro-mechanical equipments.

(50X6 G.I Strip wt.2.3 kg/m,

49 Supply, laying and erection of 60 Kg 77.77

25mm(w) x 3mm(T) etc. sizes as

required, HOT dip galvanized GI Strip

including supply & fixing using GI

spacers, saddles when laid inside the

building and inclusive of excavation &

refilling of earth when laid outside the

building & interconnection with earth

pit & all electro-mechanical

equipments. (25X3 G.I Strip, 0.6 Kg/m,

50 Supply, laying and erection of 38 Kg 794.87

40mm(w) x 6mm(T) etc. sizes Copper

Strip including supply & fixing of

bolts, saddles when laid inside the

Signature of Contractor Executive Engineer (M&E)

building and inclusive of excavation &

refilling of earth when laid outside the

building & interconnection with earth

pit & Tr. neutral. (40X6 Cu. Strip,

Kg/m, 1.88 x 20mtr.=38Kg.)

Copper Bolt,Nuts ,Washers shall be

used for Connecting Earth electrode

to individual eqp. Bitumen shall be

used at the place of joint/welding.

51 Supply, laying and erection of 15 Kg 794.87

25mm(w) x 3mm(T) etc. sizes Copper

Strip including supply & fixing of

bolts, saddles when laid inside the

building and inclusive of excavation &

refilling of earth when laid outside the

building & interconnection with earth

pit & PLC panel. (25 X3 Cu. Strip,

20mtr.=15.22Kg.)

Copper Bolt,Nuts ,Washers shall be

used for Connecting Earth electrode

to individual eqp. Bitumen shall be

used at the place of joint/welding.

(PLC Panel Earthing)

52 SITC of HOT Dip Galvanized iron strip 10 Kg 77.77

wire 8 SWG (For LDB, LCS, etc.)

(8 SWG G.I Strip, 0.103 Kg/m, 0.103 x

53 INTERNAL WIRING 150 Mtr 82.82

SITC of Mains & outlet points wiring

with 1.1 kV grade FRLS PVC insulated

ISI marked flexible stranded copper

conductor wires with medium class

min. 25mm. dia. Electrical grade PVC

pipe and accessories to be erected

concealed in / to be run on surface /

wall / ceiling with following sizes as

mentioned below. The unit rate

wirings shall be with connector, PVC

junction box, wires, holder, ceiling

rose, angle holder, switch, sockets,

switch board, brass chromium /

cadmium plated machine screws,

phase and neutral wires, green Earth

continuity wires etc. as required to

complete wiring from LDB panel to

the final outlet termination points.

The wiring shall be as per IS:732,

IS:4648 and as per tender

specification / IS.

Signature of Contractor Executive Engineer (M&E)

(a) SITC of Mains wiring with 3 wire

54 SITC of Mains wiring with 3 wire 2.5 100 Mtr 102.01

sq.mm as per tender specification &

55 SITC of Mains wiring with 4 wire 1.5 100 Mtr 90.90

sq.mm as per tender specification &

56 SITC of Mains wiring with 4 wire 2.5 80 Mtr 126.25

sq.mm as per tender specification &

57 SITC of Point wiring for Light / fan / 37 Nos 354.51

Bell / Primary Point with 2nos. 1.5 sq.

mm & earth wire of 1.5 sq. mm

(green) both are of ISI marked 1.1 kv

grade FRLS PVC insulated multistrand

copper wires , pipe to be erected

concealed in flushed on wall / ceiling,

complete with 6A Tissino Type ISI

marked flush type switch / bell push

& accessories erected on metal / PVC

Box covered with 3 mm thick PC

(Polycarbonate) / Acrylic sheet with

necessary lamp holder / ceiling Rose

/ H. D. connector as directed with

medium class Rigid PVC pipe &

58 SITC of 6A independent Plug with 6 Nos 313.10

2nos. 1.5 sq.mm Cu. Mains size wiring

& earthwire of 1.5 sq.mm (green) both

are of ISI marked 1.1 KV grade FRLS

PVC insulated multistrand copper

wires with medium class Rigid PVC

pipe and accessories to be erected on

wall / ceiling, complete with ISI

marked 3 / 5 Pin socket and tissino

type switch erected with earth

continuity connection erected on

Metal / PVC box covered with 3 mm

thick PC(Polycarbonet) / Acrylic

59 SITC of 6/16A independent Plug with 6 Nos 607.01

2nos. 4 sq.mm Cu. Mains size wiring &

earthwire of 2.5 sq.mm (green) both

are of ISI marked 1.1 KV grade FRLS

PVC insulated multistrand copper

wires with medium class Rigid PVC

pipe and accessories to be erected on

wall / ceiling, complete with ISI

marked 3 / 5 Pin socket and tissino

Signature of Contractor Executive Engineer (M&E)

type switch erected with earth

continuity connection erected on

Metal / PVC box covered with 3 mm

thick PC(Polycarbonet) / Acrylic

60 SITC of Single Phase 20A 3 Pin Metal 4 Nos 820.00

clad Industrial Type Socket with plug

top and 20A SPMCB, suitable for flush

mounting, in 16 SWG MS box of

suitable size and covered with 3 mm

thick electrical grade hylam sheet or

equivalent ISI marked Electrical grade

Bakelite sheet and earthing with

sq.mm insulated copper wire run

inside the conduit including

interconnections etc. complete as

61 LED LIGHT FIXTURES & LIGHTING: 25 Nos 589.84

SITC of Indoor wall mounting 20Watt

or up to 25% higher wattage LED

feet Tube Light indoor fittings with

LEDs of wattage 0.2 Watt to 0.5 Watt

assembled on single MCPCB, with

housing used as a heat sink shall be

made of thick sheet Steel conforming

to IS: 513/CRCA polyester powder

coated and high U.V. & corrosion

resistance with diffuser and/or

Polycarbonate optics with company

120 to 300 V,Power Factor more than

CCT 4000 K to 6500K, Uniformity

Luminaries efficacy> 85 lumens/watt

LED driver efficiency > 85 %

(Each fitting required LM-79 & LM-80

Tube Light with integral / non-

integral driver, Surge-4KV,IP-20,

62 3 watts LED Lamps integral type,cool 4 Nos 273.71

white with PC diffuser suitable for

B22 LAMP holder

63 SITC of 380mm sweep 1400 R.P.M 2 Nos 3,082.52

exhaust fan, capacitor type, having

double ball bearing, M.S.blades,

mounting frame, forearms, suitable to

operate on 230V,50 HZ AC supply

conforming to IS: 2312.Fan shall be

Signature of Contractor Executive Engineer (M&E)

painted with epoxy grey colour

controlled by one 6 A flush type

switch on board and 6A plug point

64 SITC of 40W LED Surface / Wall 3 Nos 5,194.43

mounted LED Flood Light fittings with

High power White LEDs wattage of

1Watt and above assembled on single

MCPCB, efficiency more than

lm/w and corrosion free High

pressure die cast aluminum housing

with smooth finish powder coated and

heat sink extruded aluminium with

diffuser and Polycarbonate optics/

lenses with company mark/name

engraved or embossed

120 to 300 V,Power Factor more than

Uniformity ratio >0.45, Luminaries

efficacy> 85 lumens/watt . LED driver

efficiency > 85 %.

( Each fittings required LM-79 & LM-

80 certificates)

(IP-65), Surge -4KV Cat-III

For Indoor use: (3 nos. at Pump

65 SITC of 'B' class galvanised iron pipe 11 Nos 558.53

32 mm outside dia 45 cms long duly

welded on 20 cms x 20 cms x 3 mm

thick M.S. base plate, erected on wall

or corner for mounting luminaries

with necessary hardware materials

duly painted for wall mounting indoor

flood light fixtures on Wall of

Buildings & post top lantern.

66 EXTERNAL LIGHTING (Flood LIGHT): 4 Nos 6,088.28

SITC of 70W LED Wall mounted LED

Flood Light fittings with High power

White LEDs wattage of 1Watt and

above assembled on single MCPCB,

efficiency more than 130 lm/w and

corrosion free High pressure die cast

aluminum housing with smooth finish

powder coated and heat sink extruded

aluminium with diffuser and

Polycarbonate optics/ lenses with

company mark/name engraved or

120 to 300 V,Power Factor more than

Signature of Contractor Executive Engineer (M&E)

Uniformity ratio >0.45, Luminaries

efficacy> 85 lumens/watt . LED driver

efficiency > 85 %.

( Each fittings required LM-79 & LM-

80 certificates)

(IP-65), Surge -4KV Cat-III

For Outdoor use:

67 SITC of 40watt, Cat-III Post Top 2 Nos 4,819.72

Lantern LED fitting comprises of

MM TOP Diameter, 120 degree beam

angle with Supporting Ribs and with

0.5mt. G.I. fitting pipe (for Gate light)

68 EXTERNAL LIGHTING (STREET 4 Nos 10,178.78

SITC of Street Light Pole, steel tubular

swaged type, 7.5 meter long with

single arm & M.S.base plate with pipe

cap and over hung 1.5 m long having

dia to suit the socket of 240V LED

street light fixtures. Street light pole

unit rate shall be with (i) IP 65 SMC

box of size 20 x 15 x 15 cms. with

MCB & terminal strip inside the box

with hinged/sliding door (ii) 50mm

dia, B class GI pipe bracket

min.1.5mtr long for Incoming &

outgoing cable (iii)MS Cable Clamp of

25 x 3mm (iv)SITC of 1.5 Mtr.single

Arm bracket of medium duty MS pipe

of 4.2 cms. Out side dia complete with

suitable sleeve tubing 45 cms. long of

required size of pole top etc. and

having spread of 1.5.mtr. length with

110 deg.(v) Complete painted with

one coat of Red oxide / PU base

primer and two coats of Aluminium /

PU paint for Pole,Arm, pipe etc.

69 SITC of 70 W LED Street light fittings 4 Nos 5,976.17

with High power White LEDs wattage

of 1Watt and above assembled on

single MCPCB, efficiency more than

130 lm/w and corrosion free High

pressure die cast aluminum housing

with smooth finish powder coated and

heat sink extruded aluminium with

diffuser and Polycarbonate optics/

lenses with company mark/name

engraved or embossed

Signature of Contractor Executive Engineer (M&E)

120 to 300 V,Power Factor more than

Uniformity ratio >0.45, Luminaries

efficacy> 85 lumens/watt . LED driver

efficiency > 85 %.

( Each fittings required LM-79 & LM-

80 certificates)

Street Light (IP-65), Surge -4KV,

70 SITC of M-20 / 1:2:4 cement concrete 4 Nos 1,292.80

foundation for Street light pole &

% PCC from bottom including

excavation for the pole of size 60 x

x 120 cms. Deep in below ground level

with plinth of 45 cms x 45 cms(or

cms dia x 45 cms) high upper ground

level with necessary curing and

finishing in approved manner.

71 DIESEL GENERATOR SET 2 Each 720,245.14

SITC of 75 kVA or higher standard

rating, 415 V,50 Hz, 3 Phase, 4 wire

Diesel Generating Set. Diesel engine

shall be complete with necessary

controls and safety devices confirming

to relevant IS/BSS with latest

amendments, DG controller unit with

kWH meter. Diesel Engine shall be

suitable for continuous operation of

generator set duty inclusive of fly

wheel, air cleaner, radiator. fan with

guard, fuel pump, fuel filter, Electronic

governor, auto main fail starting,

electrical starting system with starter,

12V battery, voltage regulator,

instrument panel, Exhaust silencer,

protections against low lubrication oil

pressure ,high water temperature.

Alternator shall be 415V, 3 phase,

Hz, 4 wire, 0.8 power factor, self

excited,self regulated, brushless

type,drip proof confirming to IS:4722

with latest amendments.

The engine and alternator shall be

coupled over a sturdy common base

frame. Floor mounted, dust & vermin

proof, indoor type control panel shall

be consisting of Thermal magnetic

MCCB of suitable normal current

rating, with combined overload and

Signature of Contractor Executive Engineer (M&E)

earth fault protective relays/release,

voltmeter with selector switch,

ammeter of suitable range with

selector switch, frequency meter,

Energy meter, CTs, indicating lamps

with fuse and switch control,

complete & with necessary inter

connections, fuses, labels and other

accessories. Day fuel tank with

necessary fuel hoses to the engine, all

as per detailed specification and

complete in all respect as required.

72 SITC of Acoustic enclosure suitable for 2 Each 192,414.09

75 kVA DG set, made out of 18 SWG,

CRCA Sheet, Sound absorbing material

Rockwood of 64 density & 100 mm

thick conforming to IS:8183. The resin

bonded Rockwood covered from

inside level not more than 75 dB at a

distance of 1 mtr, as PVCT / CPCB

norms, on provided foundation.

73 Providing & laying of 50 MM Nominal 50 Mtr 62.62

OD Doubled Walled Corrugated Pipes

(DWC) of polyethylene (conforming to

IS 14930 - II) with necessary

connecting accessories like coupler,

Tee, L - Bow, etc. of same material at

required depth (90 cms) including

excavation for laying of cable below

ground/ road surface for enclosing

cable and back filling the same to

make ground as per original & as per

instruction of Engineer Incharge -

74 Lightning Protection system for 1 Nos 60,760.00

highest building at plant area by air

terminal with rod and GI strip

conductor test link to earth electrode

as per requirement

75 SAFETY ACCESSORIES 2 Nos 8,671.86

SITC of following safety accessories

complete with necessary fixing

brackets, other accessories and tools

etc. as required to complete the job.

Supply & Erecting carbon dioxide

(CO2) fire extinguisher of 6.5kg

capacity with necessary clamps made

from 50 x 6 mm M.S. Flat with nut &

bolts grouted in wall complete.

(For 1 no. for LT Room, 1 no for DG

Signature of Contractor Executive Engineer (M&E)

76 Supplying & erecting D.C.P. type fire 2 Nos. 2,226.04

extinguisher for following capacity

cartridge type with gun metal cap

gram CO2 gas cartridge, powder and

brackets confirming to IS 2171

and complete erected with necessary

clamps made from 50 x 6 mm MS flat

with nuts and bolts grouted in wall

complete, 10 kg

77 Supplying of standard first AID box 1 Nos 299.97

with antiseptic cream, medicine for

use on wounds due burn, crepe

bandage, guage bandage, medicated

ready to use bandage (Band-aid)

adhesive tape for medicinal user,

scissors, antiseptic solution (Savlon or

similar) etc. (All above contents shall

be of standard makes)

78 Supply & fixing of printed instruction 1 Nos 130.29

(First Aid) Chart both in English and

Gujarati and duly framed with front

glasses, for treatment of person

suffering from electric shock.

79 Supplying & fixing of floor mounting 1 Nos 1,798.81

stand for keeping four nos. of FIRE

buckets comprising 1500 mm in

length, 900 mm height frame made

out of 30mm X30 mm X 4 mm angle

iron with cross supports for legs,

welded with 4 hooks and duly painted

with one coat of red lead and two

coats of approved enamelled silver

paint. ( 1 set for Dg set)

80 Supply and fixing of 20 W fluorescent 17 Nos 2,540.00

lamp operated emergency light with

maintenance free battery for 3 hours

operation during mains power failure.

81 Supply and laying of Synthetic 4 Sq.mtr. 1,027.17

Insulating Mat of Class - A of min.

thickness 2mm as per IS:15652 and

with good electrical insulation

property for 1.1KV/3.3KV as per site

requirement. (For LT Panel)

82 Providing pair of rubber hand gloves 1 Nos 214.12

ISI make suitable for working on

83 LIASONING CHARGES FOR 1 Nos 10,000.00

Signature of Contractor Executive Engineer (M&E)

Power Liasoning Charges for

obtaining N.O.C from Electrical

Inspector / Statutory authority for

Power / Ele. Installation. (Fees shall

be paid by tenderer for obtaining

N.O.C. from Electrical Inspector /

Statutory authority on behalf of client

and shall be reimbursed on

submission of original receipt to

Liasoning Charges shall include

preparing required attested

documents & drawing for obtaining

NOC on behalf of client (Applicable

Fees / deposits shall be reimbursed

84 INSTRUMENTATION WORK 5 Nos. 1,426.12

PRESSURE MEASURING SYSTEM:

SITC of 0- 10 kg / cm2 - 150 mm dia,

size Pressure Gauge Design, Supply,

Installation, Testing, Commissioning

of Bourdon Type Pressure Gauge,

±1% accuracy, Direct bottom 1/2"

NPT (M) process connection, IP

Glycerine filled, SS304 Case with

Bayonet Type Bezel, SS316 L Bourdon

Tube, SS 316 Movement material,

Aluminium dial with black graduation

on white background, Micro Zero

adjustable pointer, neoprene gasket,

Blow out disc, shatter proof glass, SS

tag plate etc as per IS

85 Supply, installation, testing and 5 Nos. 29,438.47

commissioning of Pressure

Transmitter with local display along

with two valve manifold, required

fittings, tubing (all valves, fittings,

tubings, etc. shall be in SS 316 only),

all accessories, hardware, etc.

complete in all respects as per

specifications and having following

measurement ranges: Range : 0 -

4Kg/cm2 (at each pump delivery side

and Pump header )

86 LEVEL MEASURING SYSTEM FOR 5 Nos. 60,030.36

Supply, installation, testing and

commissioning of Ultrasonic type

Level Transmitter with remote type

transmitter with 20 meter cable

Signature of Contractor Executive Engineer (M&E)

between Sensor and Transmitter

along with all required accessories,

Weather proof enclosure for

transmitter for outdoor application,

mounting stand , etc. complete in all

respects as per specification and

having following measurement ranges

for liquid (Effluent) application:

Meas. Range: upto 10 m

87 Supply, installation, testing and 2 Nos 12,930.02

commissioning of Displacer type

Level Switch SS Float for dry run

protection of pump through relay

multiplication in PLC), etc., complete

in all respects and as per

Meas. Range: upto 10 m

88 ELECTRO MAGNETIC FLOWMETER 3 Nos 206,534.90

Supply, installation, testing and

commissioning of Full Bore

Electromagnetic flow meter

comprising of IP-68 Sensor with PTFE

liner , Hastelloy-C Electrode, IP-66

transmitter with 20 m cable between

sensor and transmitter along with all

mounting accessories, Weather proof

enclosure for transmitter, hardware,

mounting stand, etc. as per

specification and to complete the

work in all respect as per site

condition necessary connection with

pipe and shall have following size. PN

Meter Size : 350 mm NB

89 PLC BASED CONTROL PANEL 1 Nos 350,000.00

Supply, Installation, Testing &

Commissioning of PLC Based

Instrument control Panel with 10"

color touch screen HMI, 4G GPRS

modem with (ethernet port + SIM

slot) with SIM Card for Remote data

transmission to TEPS for monitoring

and control the EPS from TEPS,

Communication port for MFM , PLC

with Conformal Coating with ISA-

S71.04 severity level G1;G2 as a min.,

Power Surge Protection device in

Incoming 230V AC Power supply to

Signature of Contractor Executive Engineer (M&E)

UPS, 1 no. Spilt type Air Conditioner

(2 Ton 5 start rating ) , Instrument

Control Panel '(PLC Enclosure / Panel

) with necessary PLC based logic and

wiring , Min. 1 kVA online UPS (with

60 min backup along with filter for

harmonic, suitable rating SMF inbuilt

batteries along with battery charger

and all other accessories as per

standard), etc. complete in all respects

and as per specs with PLC having

minimum I/O count of 70DI /30DO /

12AI /4 AO. These are the minimum

IO requirement if any other IO,s

required to complete the work

contractor shall be provide the same

without any extra cost.

90 INSTRUMENT CABLE & ACCESSORIES 80 Mtr 144.00

'Supply, Laying, Installation,

Connection, Termination, Testing &

Commissioning of Instrument Cables

as per specs. The unit rate shall

a)Supply, loading & unloading of the

cable at site from store.

b)Shifting of cable from site store to

place of installation.

c)Fixing of cable clamps, brackets,

supports, route markers etc. where

ever required to fix the cables safely.

d)Excavation, back filling and levelling

of ground along with laying of fine

sand, protection bricks and other

necessary civil material for laying

cables outside the building.

f)Testing and submission of sketches

& reports of all the cables laid.

91 SIGNAL CABLE 80 Mtr 118.00

92 CONTROL CABLE 80 Mtr 270.00

93 INSTRUMENT CABLE TRAY 80 Mtr 832.00

Supply and installation / erection of

Perforated type cable tray of

galvanized mild steel sheets of 2 mm

thickness with required, hardware,

fitting and support structural

Signature of Contractor Executive Engineer (M&E)

accessories . All material shall be Hot

dip galvanised as per IS 2629 and

tray hardware shall be in GI. Support

structure shall be of structural steel

for mounting the cable tray on wall /

cable trench or as per site condition,

600 X 25 mm - Perforated type

94 200 X 25 mm - Perforated type 80 Mtr 322.00

95 50 X 25 mm - Perforated type 80 Mtr 107.00

96 CABLE END TERMINATION AND 20 Nos 136.00

'Supply, fixing, connection, testing and

commissioning of double compression

brass cable glands and crimping type

Bimetallic lugs / sockets with

necessary tools and equipments as

specified in specifications and IS

complete in all respects. The glands

and lugs / sockets shall be suitable

for cable size and type mentioned

above. The job also includes earthing

the glands and armour of the cable

with common earth bar or flexible

copper mesh as applicable.

97 SIGNAL CABLE 24 Nos 136.00

98 CONTROL CABLE 38 Nos 296.00

99 IoT Based Dual Protocol (GSM + LAN) 1 Nos 19,500.00

Gateway for Centralise Monitoring

and Data Connectivity to GPCB and

CPCB. Cloud Software Charges for the

100 Cloud Software Platform and IIoT 1 Nos 4,550,000.00

Sensors for Predictive Maintenance

and AI Powered Electrical Signature

Analysis for Electrical Pumps.

Total Amount Without GST in Rs.

Total Amount Without GST in Rs.

*The rate shall be Exclusive of all taxes (Excluding GST)

I/We agree to carry out above work at __________ % above the estimated Rate put to tender

Percentage in words ( _______________________________)

I/We agree to carry out above work at __________ % below the estimated Rate put to tender

Percentage in words ( _______________________________)

Signature of Contractor Executive Engineer (M&E)

Estimated Amount put to Estimated Amount put to

Tender Rs. 1,47,65,058.00 Tender Rs.

Add % Above Rs.____________ . Deduct % Below Rs.____________

Net Amount Rs.____________(In figures). Net Amount Rs.____________(In figures)

I/we have read the condition mentioned in this tender and agree to abide by the sam

IMPORTANT NOTE:

The rate of each items should be offered inclusive of Excise duty, packing, forwarding, insurance,

loading, unloading, shifting & transportation at store/site except GST of work of the estates under

GIDC, Bharuch GST will paid extra Please note that the agency, in whose favour the tender is

finalized by the competent authority, should have to submit the document like insurance of the

staff engaged RPFC No., Labour license etc.

1. I / we agree to supply the above materials at the rate mentioned above.

2. I / we have read the conditions mentioned in this tender & agree to abide by the same.

3. GIDC will not issue any tax exemption form i.e. ‘P’, ‘C’ or ‘D’. The tenderer may quote

rates accordingly.

4. The agency in whose favour tender is finalized has to enter into B1 agreement and

conditions and clauses of the agreement shall be binding to the agency. If agency desire

to study, the same is available from Engineer in Charge during working days and office

5. The tendered has to inspect the site and found out the quantum of repairs/overhauling

service work involved before quoting the rates.

6. Labour work required for handling, lifting lowering, shifting, loading, unloading,

transportation etc. of any pumps & allied equipments with tools & tackles shall be

arranged by the tenderer.

Signature of Contractor Executive Engineer (M&E)