SITC of 8 Mtr Mini Mast with 5 Nos of 100W LED Flood Lights at Various GPs in Karoor, Bharananganam, Ramapuram, Elikkulam, Meenachil, Kadanadu, Thalappalam, Thalanadu, Melukavu under MLA-ADS of Sri Mani C Kappan MLA

Amount

Civil Work

2.6.1 – Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

4.1.8 – Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering – All work up to plinth level: 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

5.9.1 – Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns, etc. for mass concrete

5.22.6 – Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more

5.1.2 – Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement – All work up to plinth level: 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

13.1.1 – 12 mm cement plaster of mix: 1:4 (1 cement : 4 fine sand)

2.25 – Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m

Electrical Work

90.15.1.1 – Supply, installation, testing and commissioning of Octagonal Pole made of hot dip galvanised GI sheet 70 mm top diameter, 130 mm bottom diameter, thickness 3 mm, base plate dimensions of 200 x 200 x 16 mm, suitable for windspeed as per IS 875 Part III, fixed head frame including round arm luminary carriage suitable to install 4/6 luminaries in symmetrical arrangement including connector, foundation bolt 4 nos, existing RCC foundation and junction box etc., complete. 8 Meters height

90.15.4.7 – Supply, conveyance, installation, testing and commissioning of 100W LED Flood light, output greater than 105 lumen/W, 4000-6000 K, with IP 66 protection. LED Chip make Cree/Lumilled/Nichia with power factor greater than 0.95 at full load, internal surge protection up to 8 KV, Aluminium pressure die-cast Powder coated housing, acrylic cover complete with THD less than 10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be separately accessible for maintenance (LM 79 & 80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer)

90.14.1.2 – Fabrication, supply, conveyance, installation, testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623. Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc. as required. CRCA sheet alone be used for the fabrication. Angles/flats/slotted angles etc. shall not be used for the fabrication of panel assembly. The measurements will be taken on the area of the complete sheets used for panel board including partitions, folding, shrouding etc. Supply and fabrication of MV panel board using 1.6 mm CRCA sheet, powder coated (excluding base frame)

90.14.3.2 – Supply and providing heavy duty ‘A’ section neoprene gasket in the panel board ‘U’ section rubber beading suitable for 1.60/2.00 mm sheet

OD99549/2024-2025 – Supply and fixing of 25A 2 Pole AC 1 rated power contactor, 25A Connector, Digital timer, Suitable Copper socket, 2.5 sq. mm ISI marked FRLS PVC insulated single core copper conductor cable, 1.5 sq. mm ISI marked FRLS PVC insulated single core copper conductor cable

OD99550/2024-2025 – Supply and fixing HRC fuse base of 20/32A using suitable nut and bolt, 32A 2-way neutral links mounted on DMC/SMC base and 2.5 sq. mm ISI marked FRLS PVC insulated single core copper conductor cable

OD99551/2024-2025 – Supply, conveyance and installation of Surge protector device of IP 20 Mounting type: Screw, Voltage protection level (UP), Nominal voltage: 230V, UOC: 10KV, L-N: 7 KV, L-PE: 7 KV, N-PE: 7 KV, Nominal discharge current (8/20): 10KA, Total discharge current (8/20): 60 KA, Response time: <35 ns, Ta: -10 to 55°C

90.14.5 – Supply and fabrication, conveyance and installation of angle iron frame work for wall mounting panel board

2.14.2 – Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

2.10.3 – Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

2.10.1 – Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

2.12.1 – Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

90.6.5.11 – Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections. 3 core 1.50 sq mm

90.6.5.12 – Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections. 3 core 2.50 sq mm

5.3 – Earthing with G.I. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/coke and salt) as required

90.16.4.2 – Supply and clamping the following sizes of strips on surface of wall / parapet / existing cable tray using clamps fabricated from 20 x 3 mm GI flat duly painted or heavy duty GI spacer saddles, spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required (for vertical run). 25 x 3 mm GI strip

90.16.1.3 – Supply and drawing bare earthing conductors of the following sizes along with wiring/cables and giving connection as required. 3.15 mm copper conductor (10 SWG)

90.16.5.3 – Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required. 3.15 mm (10 SWG)

90.12.1.12 – Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). 3 core 4 sq mm

90.12.9.2 – Supplying, laying and jointing of the following sizes of double wall corrugated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in ground in the existing trench. 50/38 mm or nearest size

OD99552/2024-2025 – Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3 x 4 sq. mm (19 mm)

OD99548/2024-2025 – Fabrication, supply, conveyance and installation of Granite name board indicating the cost involved, the commencement, completion and inauguration date etc.

OD99650/2024-2025 – Supply and fixing of Name Board with Angles, Flats, Square pipe, ACP Sheet including Nut & Bolt

Connection charges - KSEB

Lanoviz Security Solutions Private Limited (BID ID -2344358)

BINDU VEERAN (BID ID -2344916)

EDISON ELECTRONICS (BID ID -2345870)