CONSTRUCTION OF KUFOS STAFF QUARTERS (PART 2) ( BALANCE WORKS- ELECTRIFICATION and

Amount

DG SET

Installation, Testing and Commissioning of 200KVA, 3 Phase 415V, 0.8 power factor, comprising of diesel engine, fuel tank, alternator, base plate radiator, control panel with MCCB starting equipment exciter, home silencer and all necessary accessories etc. complete as required. (Including Acoustic Enclosure). This scope also includes the testing of Energy Meter, CTs, Relays etc and obtaining test certificate from KSEB / Electrical Inspectorate. (*All Statutory fees should be remitted by the Client / Consumeror it should be reimbursed on the submission of supporting documents).

SWITCH BOARDS

SB - 1 (EB Supply)

Supply, installation, testing & commissioning of cubicle type 50 Hz AC supply system having sufficient front surface area steel of 2mm thick for frame work and covers, 3mm thick for Switch Board Panel suitable for 415 V, 3 Phase, 4 wire, fabricated in compartmentalised design from CRCA sheet gland, plates cleaning & finishing complete with 7 tank process for powder coating in approved shade, having 800 Amps capacity extensible type TPN Aluminum alloy bus bars of high conductivity, DMC / SMC / FRP bus bar supports, with short circuit withstand capacity of 31 MVA for 1 Sec., bottom base channel of MS section not less than100 mm x 50 mm x 5 mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 25 mm x 6 mm at the rear with switch gears with required size of AL. bus bars and control wiring with 1.5 sq. mm. PVC insulated FRLSH copper conductor cables, cable alleys etc. The panel shall conform to Electrical Inspectorate & KSEB standards and it shall only be manufactured after getting approval from Electrical Electrical Inspectorate, KSEB and the consultant.

Busbar

1 Runs of 63 x 10mm AL.Busbar for each Phase

1 Runs of 40 x 10mm AL.Busbar for Neutral

Incomer

1 Nos - 400A 36kA 4P Microprocessor based MCCB with

ROM, Spreader & Shunt Release

1 Set - RYB Indication lamps with Control MCBs

3 Nos - 400/5A CL:1, 10VA CT

1 Nos - 400/5A CL:1, 10VA CT with control wiring for

adding APFC Panel in Future

1 Nos - Digital Multifunction Meter measuring V, A, F,

KWH, KVA, PF with Control MCBs

1 Nos - Earth Leakage Relay with CBCT

Surge Protection Device

1 Nos - 8 Module DIN Rail Mounting Type 1 + Type 2 /

Class 1 + class II 100kA SPD on the incoming side of EB

Supply with all necessary accessories etc. complete as

as required. The connections to RYB Phases, Neutral and

Earth shall be done using 16 Sq.mm FRLSH Single Core

Flexible Copper Conductor Cables with less than 0.45m in

length.

Outgoings

1 Nos - 250A 25kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM, Spreader,

Digital Multifunction Meter measuring V, A, F, KWH,

KVA, PF with Control MCBs and CTs

2 Nos - 200A 25kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM, Spreader,

Digital Multifunction Meter measuring V, A, F, KWH,

KVA, PF with Control MCBs and CTs

3 Nos - 160A 25kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM, Spreader,

Digital Multifunction Meter measuring V, A, F, KWH,

KVA, PF with Control MCBs and CTs

SB - 2 (DG Supply)

Supply, installation, testing & commissioning of cubicle type

Switch Board Panel suitable for 415 V, 3 Phase, 4 wire,

50 Hz AC supply system having sufficient front surface area

fabricated in compartmentalised design from CRCA sheet

steel of 2mm thick for frame work and covers, 3mm thick

for gland, plates cleaning & finishing complete with 7 tank

process for powder coating in approved shade, having 800

Amps capacity extensible type TPN Aluminum alloy bus

bars of high conductivity, DMC / SMC / FRP bus bar

supports, with short circuit withstand capacity of 31 MVA

for 1 Sec., bottom base channel of MS section not less than

100 mm x 50 mm x 5 mm thick, fabrication shall be done in

transportable sections, entire panel shall have a common

copper earth bar of size 25 mm x 6 mm at the rear with

2 Nos. earth stud, solid connections from main bus bar to

switch gears with required size of AL. bus bars and control

wiring with 1.5 sq. mm. PVC insulated FRLSH copper

conductor cables, cable alleys etc. The panel shall conform

to Electrical Inspectorate & KSEB standards and it shall

only be manufactured after getting approval from Electrical

Inspectorate, KSEB and the consultant.

Busbar

1 Runs of 63 x 10mm AL.Busbar for each Phase

1 Runs of 40 x 10mm AL.Busbar for Neutral

Incomer

1 Nos - 400A 36kA 4P Microprocessor based MCCB with

ROM, Spreader & Shunt Release

1 Set - RYB Indication lamps with Control MCBs

3 Nos - 400/5A CL:1, 10VA CT

1 Nos - Digital Multifunction Meter measuring V, A, F,

KWH, KVA, PF with Control MCBs

1 Nos - Earth Leakage Relay with CBCT

Surge Protection Device

1 Nos - 8 Module DIN Rail Mounting Type 1 + Type 2 /

Class 1 + class II 100kA SPD on the incoming side of DG

Supply with all necessary accessories etc. complete as

as required. The connections to RYB Phases, Neutral and

Earth shall be done using 16 Sq.mm FRLSH Single Core

Flexible Copper Conductor Cables with less than 0.45m in

length.

Outgoings

1 Nos - 200A 25kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM, Spreader,

Digital Multifunction Meter measuring V, A, F, KWH,

KVA, PF with Control MCBs and CTs

1 Nos - 160A 25kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM, Spreader,

Digital Multifunction Meter measuring V, A, F, KWH,

KVA, PF with Control MCBs and CTs

2 Nos - 125A 25kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM, Spreader,

Digital Multifunction Meter measuring V, A, F, KWH,

KVA, PF with Control MCBs and CTs

2 Nos - 100A 25kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM, Spreader,

Digital Multifunction Meter measuring V, A, F, KWH,

KVA, PF with Control MCBs and CTs

SUB SWITCH BOARD

SSB - 1 (Common Panel)

Supply, installation, testing & commissioning of cubicle type

Sub Switch Board Panel suitable for 415 V, 3 Phase, 4 wire,

50 Hz AC supply system having sufficient front surface area

fabricated in compartmentalised design from CRCA sheet

steel of 2mm thick for frame work and covers, 3mm thick

for gland, plates cleaning & finishing complete with 7 tank

process for powder coating in approved shade, having 400

Amps capacity extensible type TPN Aluminum alloy bus

bars of high conductivity, DMC / SMC / FRP bus bar

supports, with short circuit withstand capacity of 31 MVA

for 1 Sec., bottom base channel of MS section not less than

100 mm x 50 mm x 5 mm thick, fabrication shall be done in

transportable sections, entire panel shall have a common

copper earth bar of size 25 mm x 6 mm at the rear with

2 Nos. earth stud, solid connections from main bus bar to

switch gears with required size of AL. bus bars and control

wiring with 1.5 sq. mm. PVC insulated FRLSH copper

conductor cables, cable alleys etc. The panel shall conform

to Electrical Inspectorate & KSEB standards and it shall

only be manufactured after getting approval from Electrical

Inspectorate, KSEB and the consultant.

Busbar

1 Runs of 40 x 10mm AL.Busbar for each Phase

1 Runs of 32 x 10mm AL.Busbar for Neutral

EB Side with Metering

4 Nos - Busbar Provision for fixing CTs

1 Nos - Provision for Fixing Three Phase Energy Meter

3 Nos - 200A Bakelite/Open Type Fuse Units with HRC

Fuse of suitable rating

1 Nos - 200A Neutral Link

There shall be KSEB Sealing Provision of CT Compartment

and Metering Compartment

1 Nos - 200A 4P Switch Disconnector

1 Set - RYB Indication lamps with Control MCBs

3 Nos - 200/5A CL:1, 10VA CT

1 Nos - Digital Multifunction Meter measuring V, A, F,

KWH, KVA, PF with Control MCBs

1 Nos - 200A 4P Power Contactor (AC3)

DG Side

1 Nos - 200A 4P Switch Disconnector

1 Set RYB Indication lamps with Control MCBs

3 Nos - 200/5A CL:1, 10VA CT

1 Nos - Digital Multifunction Meter measuring V, A, F,

KWH, KVA, PF with Control MCBs

1 Nos - 200A 4P Power Contactor (AC3)

AMF control suitable for controling EB Supply & DG Supply

with AMF Relay with Control MCBs, Timer, Contactor

Mechanical Interlock and all other necessary accessories

complete with wiring as required.

Surge Protection Device

2 Nos - 4 Module DIN Rail Mounting Type 1 + Type 2 /

Class 1 + class II 100kA SPD on the incoming side of EB

Supply and DG Supply with all necessary accessories etc.

complete as required. The connections to RYB Phases,

Neutral and Earth shall be done using 10 Sq.mm FRLSH

Single Core Flexible Copper Conductor Cables with less than

0.45m in length.

Outgoings

1 Nos - 125A 4P Switch Disconnector

2 Nos - 100A 25kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM and Spreader

1 Nos - 80A 25kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM and Spreader

1 Nos - 63A 25kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM and Spreader

2 Nos - Street/Outdoor/Common Lighting Cubicle with 40A

30mA 4P RCCB, 40A 4P MCB, 40A 4P Contactor, 24Hour

OFF (Red) Push buttons, ON (Green) - OFF (Red)

Indication lamps with Control MCBs, etc.complete as

required.

METERING PANEL

Supply, installation, testing & commissioning of cubicle type

Metering Panel suitable for 415 V, 3 Phase, 4 wire, 50 Hz

AC supply system having sufficient front surface area

fabricated in compartmentalised design from CRCA sheet

steel of 2mm thick for frame work and covers, 3mm thick

for gland, plates cleaning & finishing complete with 7 tank

process for powder coating in approved shade, having 400

Amps capacity extensible type TPN Aluminum alloy bus

bars of high conductivity, DMC / SMC / FRP bus bar

supports, with short circuit withstand capacity of 31 MVA

for 1 Sec., bottom base channel of MS section not less than

100 mm x 50 mm x 5 mm thick, fabrication shall be done in

transportable sections, entire panel shall have a common

copper earth bar of size 25 mm x 6 mm at the rear with

2 Nos. earth stud, solid connections from main bus bar to

switch gears with required size of AL. bus bars and control

wiring with 1.5 sq. mm. PVC insulated FRLSH copper

conductor cables, cable alleys etc. The panel shall conform

to Electrical Inspectorate & KSEB standards and it shall

only be manufactured after getting approval from Electrical

Inspectorate, KSEB and the consultant.

Busbar

1 Runs of 25 x 10mm AL.Busbar for each Phase

1 Runs of 25 x 10mm AL.Busbar for Neutral

There shall be KSEB Sealing Provision of Busbar Chamber.

Incomer

1 Nos - 160 4P Isolator

1 Set - RYB Indication lamps with Control MCBs

There shall be KSEB Sealing Provision of Incomer Isolator

Compartment.

Surge Protection Device

1 Nos - 4 Module DIN Rail Mounting Type 1 + Type 2 /

Class 1 + class II 100kA SPD on the incoming supply side

with all necessary accessories etc. complete as required.

The connections to RYB Phases, Neutral and Earth shall be

done using 10 Sq.mm FRLSH Single Core Flexible Copper

Conductor Cables with less than 0.45m in length.

Outgoing Compartment - 1

7 Nos - Provision for fixing Three Phase Energy Meter

There shall be KSEB Sealing Provision of Metering

Compartment Door.

Outgoing Compartment - 2

21 Nos - 63A Bakelite Fuse Unit with HRC Fuse of suitable

rating

7 Nos - 63A Neutral Link

7 Nos - 40A 4P C Curve MCB

7 Nos - ACCL

Wiring

All wiring and connections shall be done from Busbar to

Energy Meters, From Energy Meters to Fuses & Neutral

Links, From Fuses & Neutral Links to MCBs, From MCBs

to ACCL etc. using 6.0 Sq.mm FRLS Single Core Flexible

Copper conductor cables.

ACCL Specification

45A Micro Controller based full load changeover system

(EB to DG & DG to EB) in Metal Enclosure with 1 Nos

45A 4P Power Contactor (AC1) in EB Side and 1 Nos 45A

4P contactor (AC1) in DG Side, 2 Nos 10A Auxiliary

Contacts for contactor interlocking, 100A Elmex connectors

for making connections in EB Side, DG Side and load etc.

complete as required. All the internal wirings shall be done

using 6.0 Sq.mm Single Core Flexible Copper conductor

cables.

Supply, installation, testing & commissioning of cubicle type

Metering Panel suitable for 415 V, 3 Phase, 4 wire, 50 Hz

AC supply system having sufficient front surface area

fabricated in compartmentalised design from CRCA sheet

steel of 2mm thick for frame work and covers, 3mm thick

for gland, plates cleaning & finishing complete with 7 tank

process for powder coating in approved shade, having 400

Amps capacity extensible type TPN Aluminum alloy bus

bars of high conductivity, DMC / SMC / FRP bus bar

supports, with short circuit withstand capacity of 31 MVA

for 1 Sec., bottom base channel of MS section not less than

100 mm x 50 mm x 5 mm thick, fabrication shall be done in

transportable sections, entire panel shall have a common

copper earth bar of size 25 mm x 6 mm at the rear with

2 Nos. earth stud, solid connections from main bus bar to

switch gears with required size of AL. bus bars and control

wiring with 1.5 sq. mm. PVC insulated FRLSH copper

conductor cables, cable alleys etc. The panel shall conform

to Electrical Inspectorate & KSEB standards and it shall

only be manufactured after getting approval from Electrical

Inspectorate, KSEB and the consultant.

Busbar

1 Runs of 25 x 10mm AL.Busbar for each Phase

1 Runs of 25 x 10mm AL.Busbar for Neutral

There shall be KSEB Sealing Provision of Busbar Chamber.

Incomer

1 Nos - 160 4P Isolator

1 Set - RYB Indication lamps with Control MCBs

There shall be KSEB Sealing Provision of Incomer Isolator

Compartment.

Surge Protection Device

1 Nos - 4 Module DIN Rail Mounting Type 1 + Type 2 /

Class 1 + class II 100kA SPD on the incoming supply side

with all necessary accessories etc. complete as required.

The connections to RYB Phases, Neutral and Earth shall be

done using 10 Sq.mm FRLSH Single Core Flexible Copper

Conductor Cables with less than 0.45m in length.

Outgoing Compartment - 1

7 Nos - Provision for fixing Three Phase Energy Meter

There shall be KSEB Sealing Provision of Metering

Compartment Door.

Outgoing Compartment - 2

21 Nos - 63A Bakelite Fuse Unit with HRC Fuse of suitable

rating

7 Nos - 63A Neutral Link

7 Nos - 40A 4P C Curve MCB

7 Nos - ACCL

Wiring

All wiring and connections shall be done from Busbar to

Energy Meters, From Energy Meters to Fuses & Neutral

Links, From Fuses & Neutral Links to MCBs, From MCBs

to ACCL etc. using 6.0 Sq.mm FRLS Single Core Flexible

Copper conductor cables.

ACCL Specification

45A Micro Controller based full load changeover system

(EB to DG & DG to EB) in Metal Enclosure with 1 Nos

45A 4P Power Contactor (AC1) in EB Side and 1 Nos 45A

4P contactor (AC1) in DG Side, 2 Nos 10A Auxiliary

Contacts for contactor interlocking, 100A Elmex connectors

for making connections in EB Side, DG Side and load etc.

complete as required. All the internal wirings shall be done

using 6.0 Sq.mm Single Core Flexible Copper conductor

cables.

400A TP MCCB WITH CONTACTOR

Supply and installation of 400A TP Microprocessor based

MCCB with 400A 4P Power Contactor (AC3) with all its

accessories in the existing MSB Panel Board complete with

connections using additional bus bars with sleeves, nut bolt

and spring washers etc. complete as required after the

dismantling of existing 200A TPN FN Isolator. The scope

also includes the complete control wiring to contactor so as

to ensure that the supply is ON when there is EB Supply only.

DISTRIBUTION BOARD

Supply and fixing of following ways surface / recess

mounting, vertical type, 415 V, TPN MCCB distribution

board of sheet steel, dust protected, duly powder coated,

inclusive of 200A tinned copper bus bar, common neutral

link, earth bar, din bar for mounting MCBs (But without

MCBs (But without MCBs and incomer) as required.

8 Way , Double Door

6 Way , Double Door

Supply and fixing of following ways surface / recess

mounting, vertical type, 415 V, TPN MCB distribution board

of sheet steel, dust protected, duly powder coated, inclusive

of 200A tinned copper bus bar, common neutral link,

earth bar, din bar for mounting MCBs (But without MCBs

and incomer) as required.

8 Way (8 + 24), Double Door

6 Way (8 + 18), Double Door

Supply and fixing of following way, horizontal type three

pole and neutral, sheet steel, MCB distribution board, 415V,

on surface/recess, complete with tinned copper bus bar,

neutral bus bar, earth bar, din bar, interconnections, powder

coated including earthing as required. (But without MCB/

RCCB/Isolator)

6 Way (8 + 18), Double Door

4 Way (8 + 12), Double Door

Supply and fixing of following way, single pole and neutral,

sheet steel, MCB distribution board, 240V, on surface /

recess, complete with tinned copper bus bar, neutral bus

bar, earth bar, din bar, interconnections, powder coated

including earthing etc. as required. (But without MCB/RCCB

/Isolator)

16 Way, Double Door

Supply and fixing following rating and breaking capacity and

pole MCCB with thermal magnetic release having 70 to 100%

setting provision and terminal spreaders in the distribution

board including making connections, etc. complete as

required.

100A 25kA 4P MCCB

Supply and fixing following rating, four pole, (three phase

and neutral), 415V, Residual Current Circuit Breaker

(RCCB), having a sensitivity current 30 mA in the existing

MCB DB complete with connections, testing and

commissioning etc. as required.

Supply and fixing following rating, double pole, (single

phase and neutral),240V, Residual Current Circuit Breaker

(RCCB), having a sensitivity current 30 mA in the existing

MCB DB complete with connections, testing and

commissioning etc. as required.

Supply and fixing 5A to 32A rating, 240/415V, 10kA, "C "

Curve, miniature circuit breaker suitable for inductive load

of following poles in the existing MCB DB complete with

connections, testing and commissioning etc as required.

Single Pole

Double Pole

Triple Pole

40A to 63A Triple Pole

MCB DUMMY

Supply and fixing single pole blanking plate in the existing

MCB DB complete etc. as required.

ISOLATOR

Supply and fixing following rating, four pole, 415V,

isolator in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

100A 4P Isolator

63A 4P Isolator

40A 4P Isolator

Supply and fixing following rating, double pole, 240V,

isolator in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

63A 2P Isolator

40A 2P Isolator

METAL ENCLOSURE

Supply and fixing Sheet Steel enclosure on surface / recess

having provision to fix MCB/Isolator complete with

connections, testing and commmissioning etc. as required.

JUNCTION BOXES

Supply, installation, testing and commisioning of IP65

thermoplastic fire retardant and weather proof junction boxes

with bakelite connectors and/or having provision for fixing 4

Pole MCBs/Isolators and glanding cables.

LT CABLES

Supply, laying, testing and commissioning of PVC 1.1 KV

grade XLPE insulated armoured Aluminium cables of the

following sizes and laying in earth excavated trenches,

clamping in built up trenches, trays, racks, risers, trusses,

walls etc using heavy duty Aluminium Flat or heavy duty GI

spacer saddles of which spacing of clamps not exceeding

40cm and pulling through pipes including all minor civil

works.

3.5C x 400 Sq.mm Al. cable

3.5C x 300 Sq.mm Al. cable

3.5C x 240 Sq.mm Al. cable

3.5C x 185 Sq.mm Al. cable

3.5C x 150 Sq.mm Al. cable

3.5C x 120 Sq.mm Al. cable

3.5C x 95 Sq.mm Al. cable

3.5C x 70 Sq.mm Al. cable

3.5C x 50 Sq.mm Al. cable

3.5C x 35 Sq.mm Al. cable

4C x 25 Sq.mm Al. cable

4C x 16 Sq.mm Al. cable

4C x 10 Sq.mm Al. cable

4C x 6 Sq.mm Al. cable

4C x 2.5sq.mm Copper Armoured cable

2C x 2.5sq.mm Copper Armoured cable

4C x 1.5sq.mm Copper Armoured cable

2C x 1.5sq.mm Copper Armoured cable

GLANDING AND TERMINATION

Supply and making end termination with brass compression

gland and alluminium lugs for following size of PVC

insulated and PVC sheathed/ XLPE Aluminium conductor

cable of 1.1 KV grade as required.

3.5C x 400 Sq.mm Al. cable

3.5C x 300 Sq.mm Al. cable

3.5C x 240 Sq.mm Al. cable

3.5C x 185 Sq.mm Al. cable

3.5C x 150 Sq.mm Al. cable

3.5C x 120 Sq.mm Al. cable

3.5C x 95 Sq.mm Al. cable

3.5C x 70 Sq.mm Al. cable

3.5C x 50 Sq.mm Al. cable

3.5C x 35 Sq.mm Al. cable

4C x 25 Sq.mm Al. cable

4C x 16 Sq.mm Al. cable

4C x 10 Sq.mm Al. cable

4C x 6 Sq.mm Al. cable

4C x 2.5sq.mm Copper Armoured cable

2C x 2.5sq.mm Copper Armoured cable

4C x 1.5sq.mm Copper Armoured cable

2C x 1.5sq.mm Copper Armoured cable

GLAND EARTHING

Supply and providing gland earthing using Aluminium or

Copper strip / shim / wire using copper sockets etc.

complete as required conforming to Electrical Inspectorate

Standards.

3.5C x 400 Sq.mm Al. cable

3.5C x 300 Sq.mm Al. cable

3.5C x 240 Sq.mm Al. cable

3.5C x 185 Sq.mm Al. cable

3.5C x 150 Sq.mm Al. cable

3.5C x 120 Sq.mm Al. cable

3.5C x 95 Sq.mm Al. cable

3.5C x 70 Sq.mm Al. cable

3.5C x 50 Sq.mm Al. cable

3.5C x 35 Sq.mm Al. cable

4C x 25 Sq.mm Al. cable

4C x 16 Sq.mm Al. cable

4C x 10 Sq.mm Al. cable

4C x 6 Sq.mm Al. cable

4C x 2.5sq.mm Copper Armoured cable

2C x 2.5sq.mm Copper Armoured cable

4C x 1.5sq.mm Copper Armoured cable

2C x 1.5sq.mm Copper Armoured cable

EARTHING

Supply and providing earthing with CI earth plate 1200mm x

1200mm x 12.6mm thick electrode including accessories,

and providing masonary enclosure with cover plate having

locking arrangement and watering pipe of 2.7 meter long

etc. with charcoal/coke and salt as required conforming to

relevant IS and Electrical Inspectorate standards etc.

Supply and providing earthing with CI earth plate 600mm x

600mm x 6mm thick electrode including accessories,

and providing masonary enclosure with cover plate having

locking arrangement and watering pipe of 2.7 meter long

etc. with charcoal/coke and salt as required conforming to

relevant IS and Electrical Inspectorate standards etc.

EARTHING CONDUCTORS

Supply and providing the earth conductors of the following

sizes and laying in earth excavated trenches, clamping in

built up trenches , walls, trays, racks, risers, trusses, etc

using heavy duty Aluminium Flat or heavy duty GI spacer

saddles of which spacing of clamps not exceeding 90cm

without making holes in the earthing conductor and pulling

through pipes including all minor civil works. All the joints

should be properly tinned and connections should only be

done using SS Nut and Bolts with double washers etc as

required.

25 x 6 mm Copper Strip

25 x 3 mm Copper Strip

8 SWG Copper Wire

10 SWG Copper Wire

MS STRUCTURALS

Supply, fabrication and installation of cable tray and supports

using M.S angles and plates of adequate size painted with

one coat of Zinc chromate primer and two coats of black

enamel paint.

Supply, fabrication and installation of Panel Board mounting

supports using C Channels of adequate size painted with two

two coat of Zinc chromate primer and two coats of black

enamel paint.

Supply, fabrication and installation of checkered plates of

6mm thickness to use above the cable trenches duly

supported with channels and duly painted with two coat of

Zinc chromate primer and two coats of black enamel paint.

and as required.

CABLE ROUTE MARKER

Supply and fixing cable route marker with 10 cm X 10 cm

X 5 mm thick G.I. plate with inscription there on, bolted /

welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long

with painting and fixing the same in ground at 5 meter

intervel with cement concrete in M.15 Grade (1:2:4) etc.

complete as required.

PIPES FOR CABLE PROTECTION

Supply and laying of the following size medium class GI

pipe in ground/wall/ceiling complete with fittings.

50mm dia

80mm dia

100mm dia

150mm dia

Supply and laying of the following size DWC HDPE pipe

ISI marked along with all accessories like socket, bend,

couplers etc. conforming to IS 14930, Part II complete

with fitting and cutting, jointing etc. in the existing trench,

complete as required.

63mm dia

90mm dia

120mm dia

160mm dia

200mm dia

DG EXHAUST PIPING

Supply and laying of 200mm dia exhaust line with flexible

including bends, flanges, nut, bolt, packing, necessary

supports etc. and painting the same using Heat resistant

Aluminum paints.

Supply and laying of 150mm dia exhaust line with flexible

including bends, flanges, nut, bolt, packing, necessary

supports etc. and painting the same using Heat resistant

Aluminum paints.

Providing thermal insulation of exhaust line glass wool with

Al. Sheet, chicken mesh, necessary supports and screws.

POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable in surface / recessed medium

class PVC conduit, with modular switch, modular plate,

suitable GI box / surface box and earthing the point with

1.5 sq.mm FRLS PVC insulated copper conductor single

core cable etc. as required.

Group B

Wiring for twin control light point with 1.5 sq.mm FRLS

PVC insulated copper conductor single core cable in surface

/recessed medium class PVC conduit, 2 way modular

switch, modular plate, suitable GI box / PVC surface box

and earthing point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable etc. as required.

Wiring for group controlled (looped) light point / fan point /

exhaust fan point / call bell point (without independent

switch etc.) with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable in surface / recessed medium

PVC conduit, and earthing the point with 1.5 sq.mm FRLS

PVC insulated copper conductor single core cable etc. as

required.

Group B

Supply and fixing two module stepped type electronic fan

regulator on the existing modular plate switch box including

connections but excluding modular plate etc. as required.

Supply and fixing suitable size GI box /PVC surface box

with modular plate and cover in front on surface or in

recess including providing and fixing 3 pin 5/6 A modular

socket outlet and 5/6 A modular switch, connections etc. as

required.

Supply and fixing suitable size GI box /PVC surface box

with modular plate and cover in front on surface or in

recess including providing and fixing 2 Nos. 3 pin 5/6 A

modular socket outlet and 2 Nos of 5/6 A modular switch,

connections etc. as required. (For light plugs to be used in

non residential buildings).

Supply and fixing suitable size GI box / PVC surface

box with modular plate and cover in front on surface or in

recess, including providing and fixing 6 pin 5/6 & 15/16 A

modular socket outlet and 15/16 A modular switch,

connections etc. as required

Supply and fixing suitable size GI box / PVC surface

box with modular plate and cover in front on surface or in

recess, including providing and fixing 2 Nos of 6 pin 5/6 &

15/16 A modular socket outlet and 2 Nos of 15/16 A

modular switch, connections etc. as required

Supply and fixing following size/ modules, GI box / PVC

surface box along with modular base and cover plate for

modular switches in surface or in recess etc. as required.

1 or 2 Module

3 Module

4 Module

6 Module

8 Module

12 Module

Supply and fixing following modular switch/socket on the

existing modular plate and switch box including connections

etc. as required.

Telephone socket outlet

TV antenna socket outlet

Data socket outlet

Supply and fixing 3 pin, 5A ceiling rose on the existing

junction box/wooden block including connections etc. as

required

Supply and fixing modular blanking plate on the existing

modular plate & switch box excluding modular plate as

required.

CIRCUIT WIRING

Wiring for circuit / submain wiring along with earth wire

with the following sizes of FRLS PVC insulated copper

conductor, single core cable in surface / recessed medium

class PVC conduit as required.

2 x 1.5 sqmm + 1 x 1.5 sq.mm earth wire

2 x 2.5 sqmm + 1 x 2.5 sq.mm earth wire

2 x 4.0 sqmm + 1 x 4.0 sq.mm earth wire

4 x 4.0 sqmm + 2 x 4.0 sq.mm earth wire

4 x 6.0 sqmm + 2 x 6.0 sq.mm earth wire

4 x 10.0 sqmm + 2 x 6.0 sq.mm earth wire

TELEPHONE, DATA, CCTV & TV WIRING

Supply and drawing following pair 0.5mm dia FRLS PVC

insulated annealed copper conductor, unarmoured telephone

cable in the existing surface/recessed PVC conduit as

required.

Supply and drawing of UTP 4 pair CAT 6 LAN Cable in the

existing surafce/recessed PVC conduit as required.

1 run of cable

Supply and drawing co-axial TV cable RG-6 grade, 0.7mm

solid copper conductor PE insulated, shielded with fine

tinned copper braid and protected with PVC sheath in the

existing surface/recessed PVC conduit as required.

SUPPLY AND LAYING OF CONDUITS

Supply and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of

recessed conduit as required.

SUPPLY OF LIGHT & OTHER FITTINGS

Supply and providing the following fittings and items at site

Battern/Angle Holder

LED Bulb (up to 12W)

20W LED Tube Set

24W LED Tube Set

100W LED Flood Light

50W LED Flood Light

26W BLDC Ceiling Fan of Sweep 1200mm

High Speed Metal Type Exhaust Fan of Sweep 225mm

High Speed Shutter Type Exhaust Fan of Sweep 200mm

High Speed Shutter Type Exhaust Fan of Sweep 150mm

INSTALLATION OF LIGHT & OTHER FITTINGS

Installation, testing and commissioning of PVC battern /

angle holder fitting complete with all accessories directly on

ceiling/wall, including giving connections etc. as required.

Installation, testing and commissioning of pre-wired,

flourescent fitting/compact flourescent fitting of all types

complete with all accessories and tube/lamp etc. directly on

ceiling/wall, including connections with 1.5 sq.mm FRLS

PVC insulated, copper conductor, single core cable and

earthing etc. as required.

Installation, testing and commissioning of 100W LED Flood

light fittings complete with all accessories directly on wall/

piller/ceiling, including giving connections etc. as required.

Installation, testing and commissioning of 50W LED Flood

light fittings complete with all accessories directly on wall/

piller/ceiling, including giving connections etc. as required.

Installation, testing and commissioning of ceiling fan,

including wiring the down rods of standard length (up to

30cm) with 1.5 sq.mm FRLS PVC insulated, copper .

conductor, single core cable etc. as required

Installation of exhaust fan in the existing opening, including

making good the damage, connection, testing,

commissioning etc. as required.

up to 450mm sweep

HIGH MAST LIGHT

Supply Part

Supply of 12 Meter High Mast shaft in one section suitable

for 55 m/sec wind speed along with head frame, luminaires

carriage suitable for 6 luminaires in symmetrical arrangement

and other complete accessories manufactured in factory.

Supply of raising lowering system comprising double drum

winch, 5mm diameter SS wire rope, trailing cable, connector,

integral power tool motor, manual handle, junction box,

lightning finial rod.

Supply of foundation bolts manufactured from special steel

along with nuts, washers, anchor plate and common

template etc. complete as required.

Supply of 150W LED Flood Light

Supply of LED type single dome aviation obstruction light

Installation Part

Construction of shallow foundation with M20 grade concrete

for the highmast considering the safe soil bearing capacity at

site as 10 T/sqmtr at 2 metre depth with all materials and

labour.

Erection of the high mast with the help of suitable tools and

plants, wiring of luminaires with all wiring materials like PVC

insulated PVC sheathed flexible cable of suitable copper

conductor cores of 1.5 sq. mm, lugs, MCB and all labour.

CCTV CAMERA

Supply Part

Supply of the following IP Camera System with all necessary

accessories etc. complete as required and providing 2 Years

Complete Warranty and Service Support.

IR Night Vision Bullet Camera (8.0 Mega Pixel & 30 Meter)

Switch (8 Channel)

NVR (8 Channel )

Surveillance Hard Disk (4 TB )

LED Monitor (17.3)

SMPS 10A

White Surface Box (4'' x 4'')

NVR Wall Mount Rack (6U)

Installation Part

Installation of Camera System with all required accessoriesand labour.

ENERGY METER & CT

Supply and installation of the following Energy Meters and CTs after getting it tested from Electrical Inspectorate / KSEB / TMR. (All Statutory fees shall be remitted by the Client / Consumer or it shall be reimbursed on the submission of supporting documents.).

Three Phase 4 Wire CL : 1 (Direct Operated)

Three Phase 4 Wire CL : 0.5S (CT Operated)

Single Phase 2 Wire CL : 1

100/5A CL : 0.5S, 5VA Resin Cast CT

150/5A CL : 0.5S, 5VA Resin Cast CT

200/5A CL : 0.5S, 5VA Resin Cast CT

SAFETY EQUIPMENTS

Supply and fixing MV danger notice plate of 200 mm x 150mm, made of mild stee,l at least 2mm thick and vitreous enameled white on both sides and with inscriptions in signal red colour on front side as required.

Supply and fixing 2Kg Dry Chemical Powder (DCP) type fire extinguisher complete with Gun Metal cap, hose with squeeze grip nozzle, wall fixing brackets conforming to BIS: 2171 and with ISI mark

Supply and fixing safety instruction chart in word duly framed in good frame work as required.

Supply and providing a set of 2 Nos. 9.5 Litre capacity GI bucket painted in post office red colour with prior coat of red oxide paint and written with white paint "FIRE" and mounted on MS angle iron frame with bracket of appropriate size and capacity including filling sand etc.

Supply and providing First Aid Box as approved by St.John Ambulance Brigade / Indian Red Cross conforming to IS 2217 : 1963

Supply and fixing laminated shock treatment chart duly mounted on a good frame work

Supply and providing electrical grade rubber mat of size 2m x 1m having 12mm thickness in front of panels and DBs conforming to IS 15652 : 2006 standard.

Supply and providing electrical grade rubber mat of size 2m x 1m having 6mm thickness in front of panels and DBs conforming to IS 15652 : 2006 standard.

Supply and providing tested industrial safety helmet conforming to IS 2925 : 1984

NAMING FOR IDENTIFICATION

Painting letters or figures of 2.5cm/4.5cm sizes with enamel paint as identification mark to Panel boards, DBs etc as required.

EARTH EXCAVATION AND BACK FILLING

Excavation of all types of soils for the laying of XLPE

insulated power cable, GI / HDPE / RCC Pipes, Earthing

Copper conductors to the required width and depth up to

1.2m and back filling after providing sand cushioning and

protective covering by laying bricks breadth wise above the

cable. The supply of sand and bricks will come within this

scope. The trench dimensions and specifications shall be as

per the Electrical Inspectorate, KSEB & CPWD standards.

Excavation and Back Filling

Supply and laying of Bricks

Supply and filling of sand

DOCUMENTATION

Preparation of drawings and getting approval from Electrical Inspectorate. (*All Statutory fees shall be remitted by the Client / Consumer or it shall be reimbursed on the submission of supporting documents).

Submission of completion report, arranging Inpsection andobtaining Sanction Order from Electrical Inspectorate .(All Statutory fees shall be remitted by the Client / Consumer or it shall be reimbursed on the submission of supporting documents.).

Co-ordination with KSEB for getting additional power allocation by the submission of 7 sets of HT agreement and executing the agreement etc.(All Statutory fees shall be remitted by the Client / Consumer or it shall be reimbursed on the submission of supporting documents.).

Supply, Installation, Testing and Commissioning of Passenger Lift of reputed make. (Make:Schindler Group,KONE or equalent )

EXCLUSIVE OF GST

Note :1 All materials, Items, Equipment shall be best branded items with IS and approved by client/KEL

2:Rate should be inclusive of installation, testing and commissioning cost for all items

3.Rate should be Exclusive of GST.

4.Work should be executed as per DSR/PWD/Irrigation Dept. specification and direction of Engineer at site.

8.ELECTRICAL: Note: Rate should be inclusive of preparation of schematic diagram and getting approval from KSEB/Electrical Inspectorate. Statutory fees paid to KSEB/EI shall be paid by us separately.

9.1 Make of Electrical equipments/materials

All electrical materials/equipments shall be of best branded items with ISI, strictly as per schedule specification

Panel Boards: CPRI certified reputed manufacturers make

MCB/ELCB/DB - L&T/LEGRAND/SCHNEIRDER or equivalent

Cables & wires - Finolex/KEI/POLYCAB/RPG/V-GUARD

Switches/Sockets/Regulators - SCHEIDER/ABB/HAVELS/LEGRAND or equivalent

Rigid PVCPipes/Casing & Capping - A-ONE/REPUTED MAKE with ISI , Precession, Balco, GEO

Cable Glands & Sockets - REPUTED MAKE , Cosmos

Indicating Lamps - TEKINIC/RISHUB/STC, L&T, Schneider or equivalent

Ceiling/Exhaust fan: Havells, Orient, Usha, Crompton Greaves, Bajaj

SAAJCONSTRUCTIONS