Providing Architectural Facade Illumination to Gopurams at Arulmigu Mariamman Temple, Samayapuram in Trichy District

Amount

Design, supply, testing and commisioning of 6 metres Mini mast lighting unit (Bajaj / Philips / Crompton make or equivalent) complete with Hot dip Galvanised and suitable for 45 m/sec wind velocity and above . The mini mast structure should have hend and hence . The Erection of High mast by providing concreting 1:2:4 mix RCC masonry foundation pedestal. The RCC pedestal projection should be 30cm above the ground level. and foundation suitable to the safe bearing capacity of the soil at 12 T/m2 at 1.5m depth of below ground level and necessarygalvanised bolts, nuts, washers and anchor plate and template etc. complete as per standard specification of IS-875-1987 . (approved by PWD) and the Anodised steel angle of 6mm thick frame arrangment (designed as per the instruction from the site engineer )at the top of the pole suitable for mounting the 4 nos. LED luminaries as below with manual ladder arrangments with safety rung and feeder pillar Box with automatic timer system including multicore power cable and signal cable wiring , control MCB swtiches , 4 way heavy duty Connector etc. Complete as specified in the relevant ISS ( approved by PWD) with earth connections.

a)Supply and Installation of rectangular shaped single headed exterior rated architectural and landscape flood light with RGB with neutral white light LED luminaire. The luminaire housing material shall be extruded aluminum with die- cast aluminum end caps, electrostatically applied polyester powder coating finish with Tilting angle shall be ±90°, system wattage shall be less than or equal to 150W at full load and system lumen output of not less than 7,500 lumens and intensity not less than 1,04,500cd . Fixture shall be available with architectural optics with choice of beam angles of 10° Narrow beam. The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and clear tempered glass for better illumination. Fixture dimension shall be not larger than 150 x 140 x 570 mm with bracket and weight not more than 7.5kgs. Luminaire should have IP67 rated male/female connectors for DMX through wiring. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture shall have auto-ranging input voltage for 220 – 240 VAC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 3 pole round cable L=50cm, 3x1.0mm2 with flying wires and 4 pole round cable L=50cm, 4x0.5mm2 for DMX connectivity.-1 no. (Higher end Like Philips / Havells/ Crompton/ wipro/ equivalent)

b)Supply and Inatallation of rectangular shaped single headed exterior rated architectural and landscape flood light with RGB with neutral white light LED luminaire. The luminaire housing material shall be extruded aluminum with die- cast aluminum end caps, electrostatically applied polyester powder coating finish with Tilting angle shall be ±90°, system wattage shall be less than or equal to 150W at full load and system lumen output of not less than 7,800 lumens and intensity not less than 66,640cd . Fixture shall be available with architectural optics with choice of beam angles of 15° Narrow beam. The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and clear tempered glass for better illumination. Fixture dimension shall be not larger than 150 x 140 x 570 mm with bracket and weight not more than 7.5kgs. Luminaire should have IP67 rated male/female connectors for DMX through wiring. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture shall have auto-ranging input voltage for 220 – 240 VAC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 3 pole round cable L=50cm, 3x1.0mm2 with flying wires and 4 pole round cable L=50cm, 4x0.5mm2 for DMX connectivity. -1 no. (Higher end Like Philips / Havells/ Crompton/ wipro/ equivalent)

c)Supply and Installation of rectangular shaped single headed exterior rated architectural and landscape flood light with RGB with neutral white light LED luminaire. The luminaire housing material shall be extruded aluminum with die- cast aluminum end caps, electrostatically applied polyester powder coating finish with Tilting angle shall be ±90°, system wattage shall be less than or equal to 150W at full load and system lumen output of not less than 8,100 lumens and intensity not less than 19,200cd . Fixture shall be available with architectural optics with choice of beam angles of 30° Mid beam. The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and clear tempered glass for better illumination. Fixture dimension shall be not larger than 150 x 140 x 570 mm with bracket and weight not more than 7.5kgs. Luminaire should have IP67 rated male/female connectors for DMX through wiring. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture shall have auto-ranging input voltage for 220 – 240 VAC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 3 pole round cable L=50cm, 3x1.0mm2 with flying wires and 4 pole round cable L=50cm, 4x0.5mm2 for DMX connectivity.-2nos. (Higher end Like Philips / Havells/ Crompton/ wipro/ equivalent) .The rate quoted are inclusive of free Annual maintenance for three years from the date of completion of work.

Rajagopuram Front

Design, supply, testing and commisioning of 6 metres Mini mast lighting unit (Bajaj / Philips / Crompton make or equivalent) complete with Hot dip Galvanised and suitable for 45 m/sec wind velocity and above . The mini mast structure should have hend and hence . The Erection of High mast by providing concreting 1:2:4 mix RCC masonry foundation pedestal. The RCC pedestal projection should be 30cm above the ground level. and foundation suitable to the safe bearing capacity of the soil at 12 T/m2 at 1.5m depth of below ground level and necessarygalvanised bolts, nuts, washers and anchor plate and template etc. complete as per standard specification of IS-875-1987 . (approved by PWD) and the Anodised steel angle of 6mm thick frame arrangment (designed as per the instruction from the site engineer )at the top of the pole suitable for mounting the 4 nos. LED luminaries as below

with manual ladder arrangments with safety rung and feeder pillar Box with automatic timer system including multicore power cable and signal cable wiring , control MCB swtiches , 4 way heavy duty Connector etc. Complete as specified in the relevant ISS ( approved by PWD) with earth connections.

a)Supplyand Installation of rectangular shaped single headed exterior rated architectural and landscape flood light with RGB with neutral white light LED luminaire. The luminaire housing material shall be extruded aluminum with die- cast aluminum end caps, electrostatically applied polyester powder coating finish with Tilting angle shall be ±90°, system wattage shall be less than or equal to 150W at full load and system lumen output of not less than 7,800 lumens and intensity not less than 66,640cd . Fixture shall be available with architectural optics with choice of beam angles of 15° Narrow beam. The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and clear tempered glass for better illumination. Fixture dimension shall be not larger than 150 x 140 x 570 mm with bracket and weight not more than 7.5kgs. Luminaire should have IP67 rated male/female connectors for DMX through wiring. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture shall have auto-ranging input voltage for 220 – 240 VAC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 3 pole round cable L=50cm, 3x1.0mm2 with flying wires and 4 pole round cable L=50cm, 4x0.5mm2 for DMX connectivity.-1 no. (Higher end Like Philips / Havells/ Crompton/wipro/ equivalent)

b)Supply and Installation of rectangular shaped single headed exterior rated architectural and landscape flood light with RGB with neutral white light LED luminaire. The luminaire housing material shall be extruded aluminum with die- cast aluminum end caps, electrostatically applied polyester powder coating finish with Tilting angle shall be ±90°, system wattage shall be less than or equal to 150W at full load and system lumen output of not less than 8,100 lumens and intensity not less than 19,200cd . Fixture shall be available with architectural optics with choice of beam angles of 30° Mid beam. The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and clear tempered glass for better illumination. Fixture dimension shall be not larger than 150 x 140 x 570 mm with bracket and weight not more than 7.5kgs. Luminaire should have IP67 rated male/female connectors for DMX through wiring. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture shall have auto-ranging input voltage for 220 – 240 VAC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 3 pole round cable L=50cm, 3x1.0mm2 with flying wires and 4 pole round cable L=50cm, 4x0.5mm2 for DMX connectivity.-3nos. (Higher end Like Philips / Havells/ Crompton/ wipro/ equivalent) .The rate quoted are inclusive of free Annual maintenance for three years from the date of completion of work.

Rajagopuram Front

Design, supply, testing and commisioning of 6 metres Mini mast lighting unit (Bajaj / Philips / Crompton make or equivalent) complete with Hot dip Galvanised and suitable for 45 m/sec wind velocity and above . The mini mast structure should have hend and hence . The Erection of High mast by providing concreting 1:2:4 mix RCC masonry foundation pedestal. The RCC pedestal projection should be 30cm above the ground level. and foundation suitable to the safe bearing capacity of the soil at 12 T/m2 at 1.5m depth of below ground level and necessarygalvanised bolts, nuts, washers and anchor plate and template etc. complete as per standard specification of IS-875-1987 . (approved by PWD) and the Anodised steel angle of 6mm thick frame arrangment (designed as per the instruction from the site engineer )at the top of the pole suitable for mounting the 4 nos. LED luminaries as below

with manual ladder arrangments with safety rung and feeder pillar Box with automatic timer system including multicore power cable and signal cable wiring , control MCB swtiches , 4 way heavy duty Connector etc. Complete as specified in the relevant ISS ( approved by PWD) with earth connections.

a)Supply and Installation of rectangular shaped single headed exterior rated architectural and landscape flood light with RGB with neutral white light LED luminaire. The luminaire housing material shall be extruded aluminum with die- cast aluminum end caps, electrostatically applied polyester powder coating finish with Tilting angle shall be ±90°, system wattage shall be less than or equal to 150W at full load and system lumen output of not less than 7,800 lumens and intensity not less than 66,640cd . Fixture shall be available with architectural optics with choice of beam angles of 15° Narrow beam. The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and clear tempered glass for better illumination. Fixture dimension shall be not larger than 150 x 140 x 570 mm with bracket and weight not more than 7.5kgs. Luminaire should have IP67 rated male/female connectors for DMX through wiring. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture shall have auto-ranging input voltage for 220 – 240 VAC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 3 pole round cable L=50cm, 3x1.0mm2 with flying wires and 4 pole round cable L=50cm, 4x0.5mm2 for DMX connectivity..-1 no. (Higher end Like Philips / Havells/ Crompton/ wipro/ equivalent)

b)Supply and Installation of rectangular shaped single headed exterior rated architectural and landscape flood light with RGB with neutral white light LED luminaire. The luminaire housing material shall be extruded aluminum with die- cast aluminum end caps, electrostatically applied polyester powder coating finish with Tilting angle shall be ±90°, system wattage shall be less than or equal to 150W at full load and system lumen output of not less than 8,100 lumens and intensity not less than 19,200cd . Fixture shall be available with architectural optics with choice of beam angles of 30° Mid beam. The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and clear tempered glass for better illumination. Fixture dimension shall be not larger than 150 x 140 x 570 mm with bracket and weight not more than 7.5kgs. Luminaire should have IP67 rated male/female connectors for DMX through wiring. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture shall have auto-ranging input voltage for 220 – 240 VAC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 3 pole round cable L=50cm, 3x1.0mm2 with flying wires and 4 pole round cable L=50cm, 4x0.5mm2 for DMX connectivity.- 2nos. (Higher end Like Philips / Havells/ Crompton/wipro/ equivalent)

c)Supply and installation of rectangular shaped single headed exterior rated architectural and landscape flood light with RGB with neutral white light LED luminaire. The luminaire housing material shall be extruded aluminum with die- cast aluminum end caps, electrostatically applied polyester powder coating finish with Tilting angle shall be ±90°, system wattage shall be less than or equal to 150W at full load and system lumen output of not less than 7,800 lumens and intensity not less than 10,450cd . Fixture shall be available with architectural optics with choice of beam angles of 45° Wide beam. The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and clear tempered glass for better illumination. Fixture dimension shall be not larger than 150 x 140 x 570 mm with bracket and weight not more than 7.5kgs. Luminaire should have IP67 rated male/female connectors for DMX through wiring. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture shall have auto-ranging input voltage for 220 – 240 VAC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 3 pole round cable L=50cm, 3x1.0mm2 with flying wires and 4 pole round cable L=50cm, 4x0.5mm2 for DMX connectivity.-1 no. (Higher end Like Philips / Havells/ Crompton/ wipro/ equivalent) .The rate quoted are inclusive of free Annual maintenance for three years from the date of completion of work.

West Gopuram

Design, supply, testing and commisioning of 6 metres Mini mast lighting unit (Bajaj / Philips / Crompton make or equivalent) complete with Hot dip Galvanised and suitable for 45 m/sec wind velocity and above . The mini mast structure should have hend and hence . The Erection of High mast by providing concreting1:2:4 mix RCC masonry foundation pedestal. The RCC pedestal projection should be 30cm above the ground level. and foundation suitable to the safe bearing capacity of the soil at 12 T/m2 at 1.5m depth of below ground level and necessarygalvanised bolts, nuts, washers and anchor plate and template etc. complete as per standard specification of IS-875-1987 . (approved by PWD) and the Anodised steel angle of 6mm thick frame arrangment (designed as per the instruction from the site engineer )at the top of the pole suitable for mounting the 2 nos. LED luminaries as below

with manual ladder arrangments with safety rung and feeder pillar Box with automatic timer system including multicore power cable and signal cable wiring , control MCB swtiches , 4 way heavy duty Connector etc. Complete as specified in the relevant ISS ( approved by PWD) with earth connections.

a)Supply and installation of rectangular shaped single headed exterior rated architectural and landscape flood light with RGB with neutral white light LED luminaire. The luminaire housing material shall be extruded aluminum with die- cast aluminum end caps, electrostatically applied polyester powder coating finish with Tilting angle shall be ±90°, system wattage shall be less than or equal to 150W at full load and system lumen output of not less than 8,100 lumens and intensity not less than 19,200cd . Fixture shall be available with architectural optics with choice of beam angles of 30° Mid beam. The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and clear tempered glass for better illumination. Fixture dimension shall be not larger than 150 x 140 x 570 mm with bracket and weight not more than 7.5kgs. Luminaire should have IP67 rated male/female connectors for DMX through wiring. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture shall have auto-ranging input voltage for 220 – 240 VAC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 3 pole round cable L=50cm, 3x1.0mm2 with flying wires and 4 pole round cable L=50cm, 4x0.5mm2 for DMX connectivity.- 2nos. (Higher end Like Philips / Havells/ Crompton/ wipro/ equivalent) .The rate quoted are inclusive of free Annual maintenance for three years from the date of completion of work.

North Gopuram 1 No and South Gopuram 1 No

Design, supply, testing and commissioning of Pedestal type channel made up of anodised steel angle of 6mm thick frame with leg supports and side supports with proper earth connections and suitable concrete arrangments on the roof top to fix the LED flood light ( frame design as per the instruction from the site engineer) suitable for 45 m/sec wind velocity and above . The structure should have hend and hence and the LED luminaries details as below

a).Supply and installation of rectangular shaped single headed exterior rated architectural and landscape flood light with RGB with neutral white light LED luminaire. The luminaire housing material shall be extruded aluminum with die- cast aluminum end caps, electrostatically applied polyester powder coating finish with Tilting angle shall be ±90°, system wattage shall be less than or equal to 150W at full load and system lumen output of not less than 7,500 lumens and intensity not less than 1,04,500cd . Fixture shall be available with architectural optics with choice of beam angles of 10° Narrow beam. The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and clear tempered glass for better illumination. Fixture dimension shall be not larger than 150 x 140 x 570 mm with bracket and weight not more than 7.5kgs. Luminaire should have IP67 rated male/female connectors for DMX through wiring. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture shall have auto-ranging input voltage for 220 – 240 VAC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 3 pole round cable L=50cm, 3x1.0mm2 with flying wires and 4 pole round cable L=50cm, 4x0.5mm2 for DMX connectivity. - 1 no. (Higher end Like Philips / Havells/ Crompton/ wipro/ equivalent) .The rate quoted are inclusive of free Annual maintenance for three years from the date of completion of work.

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 350 kglms and maximum water cement ratio of 0.50, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete

Rajagopuram Left & Right Side - 2 No, Rajagopuram Back - 1 No West Gopuram Left and Right Side - 2 No

Design, supply, testing and commissioning of Pedestal type channel made up of anodised steel angle of 6mm thick frame with leg supports and side supports with proper earth connections and suitable concrete arrangments on the roof top to fix the LED flood light ( frame design as per the instruction from the site engineer) suitable for 45 m/sec wind velocity and above . The structure should have hend and hence and the LED luminaries details as below

a)Supply and installation of rectangular shaped single headed exterior rated architectural and landscape flood light with RGB with neutral white light LED luminaire. The luminaire housing material shall be extruded aluminum with die- cast aluminum end caps, electrostatically applied polyester powder coating finish with Tilting angle shall be ±90°, system wattage shall be less than or equal to 150W at full load and system lumen output of not less than 7,800 lumens and intensity not less than 66,640cd . Fixture shall be available with architectural optics with choice of beam angles of 15° Narrow beam. The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and clear tempered glass for better illumination. Fixture dimension shall be not larger than 150 x 140 x 570 mm with bracket and weight not more than 7.5kgs. Luminaire should have IP67 rated male/female connectors for DMX through wiring. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture shall have auto-ranging input voltage for 220 – 240 VAC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 3 pole round cable L=50cm, 3x1.0mm2 with flying wires and 4 pole round cable L=50cm, 4x0.5mm2 for DMX connectivity. -1 no. (Higher end Like Philips / Havells/ Crompton/ wipro/ equivalent) .The rate quoted are inclusive of free Annual maintenance for three years from the date of completion of work.

Rajagopuram Left & Right Side - 6 Nos, Rajagopuram Back - 2 Nos West Gopuram Back - 1 No

Design, supply, testing and commissioning of Pedestal type channel made up of anodised steel angle of 6mm thick frame with leg supports and side supports with proper earth connections and suitable concrete arrangments on the roof top to fix the LED flood light ( frame design as per the instruction from the site engineer) suitable for 45 m/sec wind velocity and above . The structure should have hend and hence and the LED luminaries details as below

a)Supply and installation of rectangular shaped single headed exterior rated architectural and landscape flood light with RGB with neutral white light LED luminaire. The luminaire housing material shall be extruded aluminum with die- cast aluminum end caps, electrostatically applied polyester powder coating finish with Tilting angle shall be ±90°, system wattage shall be less than or equal to 150W at full load and system lumen output of not less than 8,100 lumens and intensity not less than 19,200cd . Fixture shall be available with architectural optics with choice of beam angles of 30° Mid beam. The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and clear tempered glass for better illumination. Fixture dimension shall be not larger than 150 x 140 x 570 mm with bracket and weight not more than 7.5kgs. Luminaire should have IP67 rated male/female connectors for DMX through wiring. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture shall have auto-ranging input voltage for 220 – 240 VAC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 3 pole round cable L=50cm, 3x1.0mm2 with flying wires and 4 pole round cable L=50cm, 4x0.5mm2 for DMX connectivity. -1 no. (Higher end Like Philips / Havells/ Crompton/ wipro/ equivalent) .The rate quoted are inclusive of free Annual maintenance for three years from the date of completion of work.

Rajagopuram Back - 5 Nos, West Gopuram Left and Right Side - 4 Nos West Gopuram Back - 2 Nos North Gopuram Left and Right Side - 4 Nos North Gopuram Back - 4 No

Design, supply, testing and commissioning of Pedestal type channel made up of anodised steel angle of 6mm thick frame with leg supports and side supports with proper earth connections and suitable concrete arrangments on the roof top to fix the LED flood light ( frame design as per the instruction from the site engineer) suitable for 45 m/sec wind velocity and above . The structure should have hend and hence and the LED luminaries details as below

a)Supply and installation of rectangular shaped single headed exterior rated architectural and landscape flood light with RGB with neutral white light LED luminaire. The luminaire housing material shall be extruded aluminum with die- cast aluminum end caps, electrostatically applied polyester powder coating finish with Tilting angle shall be ±90°, system wattage shall be less than or equal to 150W at full load and system lumen output of not less than 7,800 lumens and intensity not less than 10,450cd . Fixture shall be available with architectural optics with choice of beam angles of 45° Wide beam. The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and clear tempered glass for better illumination. Fixture dimension shall be not larger than 150 x 140 x 570 mm with bracket and weight not more than 7.5kgs. Luminaire should have IP67 rated male/female connectors for DMX through wiring. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture shall have auto-ranging input voltage for 220 – 240 VAC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 3 pole round cable L=50cm, 3x1.0mm2 with flying wires and 4 pole round cable L=50cm, 4x0.5mm2 for DMX connectivity. -1 no. (Higher end Like Philips / Havells/ Crompton/ wipro/ equivalent) .The rate quoted are inclusive of free Annual maintenance for three years from the date of completion of work.

Garbhagraham Dome - 4 Nos Rajagopuram Left and Right Side - 2 Nos West Gopuram Back - 1 No

Supply and installation of circular shaped, exterior rated architectural and landscape spotlight with RGB with neutral white light LED luminaire. The luminaire housing material shall be die-cast aluminum housing, electrostatically applied polyester powder coating finish, system wattage shall be less than or equal to 24W at full load and system lumen output of not less than 940 lumens and intensity not less than 1,130cd. Fixture shall be available with architectural optics with choice of beam angles of 60° wide beam. The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and clear tempered glass for better illumination. Fixture dimension shall be not larger than 135*145mm with bracket and weight not more than 1.8 kgs.Luminaire should have IP67 rated male/female connectors for DMX through wiring. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture shall have auto-ranging input voltage for 220 – 240 VAC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 3 pole round cable L=50cm, 3x1.0mm2 with flying wires and 4 pole round cable L=50cm, 4x0.5mm2 for DMX connectivity. (Like Philips model no. BVP371 12LED RGBNW 220V 60 DMX 24W HE /Havells/Crompton/wipro/equivalent) .The rate quoted are inclusive of free Annual maintenance for three years from the date of completion of work.

Statue around compound wall

Supply and installation of compact size linear exterior rated architectural and landscape grazing light with RGB with neutral white light LED luminaire. The luminarie housing material of extruded aluminum with die-cast aluminum end caps, electrostatically applied polyester powder coating finish, system wattage shall be less than or equal to 24W at full load and system lumen output of not less than 870 lumens and intensity not less than 1,800cd. Fixture shall be available with high power LED and architectural optics with choice of beam angles of Elliptical 25° x 40°.The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and Clear tempered glass cover for better illumination. Fixture dimension shall be not larger than 1000 x 40 x 90 mm with bracket and weight not more than 1.6kgs. Luminaire should have IP67 male/female connectors for through power + signal connection. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture operating input voltage shall be 24V DC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 5 pole flat cable L=15cm, 2x1.5mm2 + 3x0.3mm2 with connectors. (Higher end Like Philips / Havells/ Crompton/ Wipro/ equivalent).The rate quoted are inclusive of free Annual maintenance for three years from the date of completion of work.

In between two statue around the compound - 55 Nos Front side roof statue - 8 Nos Northwest First Floor Roof Statue - 24 Nos

Supply and installation of circular shaped, exterior rated architectural and landscape spotlight with RGB with neutral white light LED luminaire. The luminaire housing material shall be die-cast aluminum housing, electrostatically applied polyester powder coating finish, system wattage shall be less than or equal to 24W at full load and system lumen output of not less than 1090 lumens and intensity not less than 17,600cd. Fixture shall be available with architectural optics with choice of beam angles of 10° narrow beam. The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and clear tempered glass for better illumination. Fixture dimension shall be not larger than 135*145mm with bracket and weight not more than 1.8 kgs.Luminaire should have IP67 rated male/female connectors for DMX through wiring. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture shall have auto-ranging input voltage for 220 – 240 VAC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 3 pole round cable L=50cm, 3x1.0mm2 with flying wires and 4 pole round cable L=50cm, 4x0.5mm2 for DMX connectivity. (Higher end Like Philips / Havells/ Crompton/ wipro/ equivalent) .The rate quoted are inclusive of free Annual maintenance for three years from the date of completion of work.

Around Compound Pillar

Design, supply, testing and commissioning of Pedestal type channel made up of anodised steel angle of 6mm thick frame with leg supports and side supports and suitable concrete arrangments on the roof top to fix the LED flood light ( frame design as per the instruction from the site engineer) suitable for 45 m/sec wind velocity and above . The structure should have hend and hence and the LED luminaries details as below

Supply and installation of linear exterior rated architectural and landscape grazing light with RGB with neutral white light LED luminaire. The luminarie housing material of extruded aluminum with die-cast aluminum end caps, electrostatically applied polyester powder coating finish, with Tilting angle shall be +15° to -90° and system wattage shall be less than or equal to 80W at full load and system lumen output of not less than 3100 lumens and intensity not less than 10,300cd. Fixture shall be available with architectural optics with choice of beam angles of 15°- 20°x 35°-40° elliptical beam. Fixture dimension shall be not larger than 1000 x 60 x 65 mm without bracket and weight not more than 4.5kgs. The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and clear tempered glass for better illumination. The white LED should have SDCM 4 for better color. Luminarie should have IP67 rated male/female connectors for DMX through wiring. Fixture shall operate in a temperature range of -40°C to 50°C and startup temperature range of -35°C to 50°C. Fixture shall have auto-ranging input voltage for 120 – 277 VAC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 3 pole round cable L=50cm, 3x1.0mm2 with flying wires and 4 pole round cable L=50cm, 4x0.5mm2 for DMX connectivity. (Higher end Like Philips / Havells/ Crompton/ Wipro/ equivalent) .The rate quoted are inclusive of free Annual maintenance for three years from the date of completion of work.

Amman sannathi exterior wall & Raja Gopuram - 15 Nos Rajagopuram - 10 No's

Design, supply , testing and commissioning of DMX controller housed in suitable MS box with lock and key arrangments with suitable pedestal type angle frame and suitable concrete arrangments (MS box design as per th instruction from the site engineer) suitable for 45m/sec wind velocity and above . The DMX control details as below

Rajagopuram side

Design, supply , testing and commissioning of DMX signal amplifier housed in suitable existing control box . The DMX signal amplifier details as below

Supply and installation of compact DMX signal amplifier that takes the incoming DMX512/RDM signal and amplify the signal and supporting bi-directional communications for discovery, addressing and DMX control of light fixtures.This unit takes the incoming DMX/RDM signal and splits the signal into six separate output channels allowing for expanding the number of devices controlled from 32 to 6 X 32. The output terminals are electronically isolated from the input & RDM-through port and share a common ground reference. All six output ports have an independent output driver to boost the DMX/RDM signal. Operating temperature shall be -10° to 35°C. The maximum power consumption shall be less than 4.5W and input voltage shall be 12-24V DC. ( Like Philips/ Havells/ crompton/wipro/ equivalent) .The rate quoted are inclusive of free Annual maintenance for three years from the date of completion of work.

East Gopuram - 1 No West Gopuram - 1 No North Gopuram - 1 No South Gopuram - 1 No

Design, supply , testing and commissioning of DMX signal amplifier housed in suitable existing control box . The DMX signal amplifier details as below

Supply and installation of compact DMX signal amplifier that takes the incoming DMX512/RDM signal and amplify the signal into long distance transmission. The housing shall be aluminum with block color finish. This compact signal amplifier supports magnetic isolation protection, protects the controllers and ensures that the DMX signal can be normally transmitted to various luminaires, improving the reliability and stability of the entire control system. The amplifier should able to transmit the DMX signal up to 100mtr or upto 64 luminaries with out signal loss. Operating temperature shall be -20° to 50°C. The maximum power consumption shall be less than 1.5W and input voltage shall be 12-24V DC. The device should be supplied as per technical specification. (Higher end Like Philips / Havells/ Crompton/wipro/ equivalent) .The rate quoted are inclusive of free Annual maintenance for three years from the date of completion of work.

East Gopuram - 2 No West Gopuram - 1 No North Gopuram - 1 No South Gopuram - 1 No Compound Lights - 1 No

Design, supply, testing and commissioning of Supply of 10 pieces of 2mtr factory made 4Pmale to female cable to connect the DMX enabled data line for better connectivity. (Higher end Like Philips / Havells/ Crompton/ wipro/ equivalent)

East Side - 5 Nos West Side - 4 Nos North Side - 4 Nos South Side - 4 Nos Garbhagraham - 4 Nos

Design, supply, testing and commissioning of Supply of 10 pieces of 2mtr factory made 5Pmale to female cable to connect the DMX enabled data line for better connectivity and DC supply. (Higher end Like Philips / Havells/ Crompton/ wipro/ equivalent)

East Side - 3 Nos West Side - 1 No North Side - 1 No South Side - 1 No Upper Statue - 3 Nos

supply and laying of 4 core 10 sq.mm PVC sheathed armoured LTUG copper cable in suitable HDPE pipe in a trench to be excavated at a depth of 0.75m and refilling the earth to make good

North side existing supply point (near step) to North Gopuram front side - 40 Mtr West side existing supply point to West gopuram front side - 40 Mtr North side existing supply point (near step) to south Gopuram front side - 40 Mtr East side security room supply point to East Gopuram front side - 80 Mtr

supply and clamping of 4 core 10 sq.mm PVC sheathed armoured LTUG copper cable in suitable HDPE pipe on wall /roof by suitable clamp

North Side Roof Top - 175 mtr West Side Roof Top - 175 mtr South Side Roof Top - 200 mtr Eash Side Roof Top - 150 mtr

supply and clamping of 4 core 2.5 sq.mm PVC sheathed armoured LTUG copper cable in suitable HDPE pipe on wall /roof by suitable clamp

North Side Roof Top - 75 mtr West Side Roof Top - 75 mtr South Side Roof Top - 75 mtr Eash Side Roof Top - 75 mtr

Earthing as per PWD standard with an earth electrode of 2 mtr. Class B GI pipe of dia not less than 32mm complete with necessary masonry work

North Side - 1 No South Side - 1 No East Side - 1 No West Side - 1 No

supply and run of CAT 6 armoured cable in HDPE/Dural line Pipe on wall or roof or ground by suitable clamps

North Side - 150 mtr South Side - 150 mtr East Side - 150 mtr West Side - 150 mtr

supply and Installation of 15 KVA three phase Microprocessor controlled Air cooled unbalanced Electronic servo voltage stablizer with High/Low voltage cut off and single phase preventer with built in manual by pass arrangments .The rate quoted are inclusive of free Annual maintenance for three years from the date of completion of work.

North Side - 1 No East Side - 1 No

Supply and fixing of pillar box made up of 16SWG MS sheeet of size 3'x 3'x2' with lock and key arrangements with suitable AI frame leg support with concrete and construction of masonry pedestal to house 1 No 4 way VTPN MCB DB ,1 No 63A 4P MCB,12 Nos 6A/32A SP MCB,L& T 4 pole Contactor MCX-3 32A,Havells 24 Hour Analog timer Switch DHTED 30016,3Nos Backlite 4Way Connector,3Nos Backlite 2Way Connector with earth conection and inter conection only Higer End

Supply and Installation of 24V/300W IP65 or above rated LED Driver for Linear Luminaires. (Higher end) .The rate quoted are inclusive of free Annual maintenance for three years from the date of completion of work.

Compound Wall

Sub Total

MIDAS ELECTRICALS PVT LTD (BID ID -1096484)