Renovation Works of Building and Fencing Work of Land for Priya Home for Mentally challenged Ladies ,Kayala, Veliyam, Kollam.

Amount

1 Building Renovation 50.6.1.4 Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand ) etc complete

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

9.123 Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVCfoam profile with homogeneous fine cellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & jointed with self driven self tapping screws of size 38 mm x 4 mm & PVC solvent cement, including fixing the frame to wall with suitable dia & length anchor fastener as per manufacturer's specification and direction of Engineer-in-charge.

9.124.2 Providing and fixing factory made 30 mm thick door shutter made of solid PVC foam profile. The styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mm x 1 mm, painted with primer, all four corners of reinforcement to be welded or sealed. Solid PVC extruded bidding (Push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5 mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rails of sixe 100mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100 mm x 8 mm complete as per manufacturer's specifications and direction of Engineer -in-charge.Decorative finish (both side wood grained finish

13.33.1 Pointing on stone work with cement mortar 1:3 ( 1 cement : 3 fine sand):Flush/ Ruled pointing

13.40 Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade:

13.85.1 Applying priming coats with primer of approved brand and manufacture, having low VOC ( Volatile Organic Compound) content.With ready mixed pink or grey primer on wood work (hard and soft wood ) having VOC content less than 50 grams/ litre

8.2.2.1 Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shadeArea of slab upto 0.50 sqm

13.60.1 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.61.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

11.41.1 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 500x500 mm.

Roofing work 4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

50.10.1 Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Interlock block paving 2.1.1 Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, disposed soil to be levelled and neatly dressed:All Kinds of soil

16.91.2 Providing and laying factory made chamfered edge Cement Concrete paver blocksin footpath, parks, lawns, drive ways or light traffic parking etc, of required strength,thickness & size/ shape, made by table vibratory method using PU mould, laid inrequired colour & pattern over 50mm thick compacted bed of sand, compacting andproper embedding/laying of inter locking paver blocks into the sand beddinglayerthrough vibratory compaction by using plate vibrator, filling the joints with sand andcutting of paver blocks as per required size and pattern, finishing and sweepingextra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

16.68 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

4 fencing around area 50.10.1 Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

16.70.2 Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts , bolts and washers as required complete as per the direction of Engineer-in- charge.Made of G.I wire of dia 4 mm. PVC coated to achieve outer dia. not less than 5 mm in required colour and shade

10.1 Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Supplying and fixing GI trafford sheet of 0.35 mm thick for roof work

Electrical works Wiring for light point/fan point/ exhaust fan point/ call bell point with 1.5 sq mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq mm FR PVC insulated copper conductor single core cable etc as required. Group C1.103

Suppling and fixing following piano type switch/ socket on the existing switch box/cver including cnnectins as required 1.23 1.23.1 5/6 A switch

2 way 5/6 A switch 1.23.2

3 pin 5/6 A socket outlet 1.23.4

TV outlet 1.23

15/16 amp switch

6 pin 15/16 amp socket outlet

Supplying & fixing stepped type electronic fan regulator on the existing plate switch box including connections but excluding modular plate etc.as required. 1.25

Supplying and fixing 1200mm ceiling fan using 16/0.20mm 3 core round copper wire connect with existing ceiling rose fittings, connecting, commissioning including all materials, and labour charges etc. complete OD

Supplying and fixing 14W LED connect with angle batten fixing, connecting, commissioning including all labour charges etc. complete OD

Supplying and fixing 20W LED tube set fitting on TW round block suspension in suitable positio, using 16/0.20 mm 3 core round copper wire connect with existing three plate ceiling rose fixing, connecting, commissioning including all labour charges etc. complete OD

Supplying and fixing 14W LED connect with bulk head fixing, connecting, commissioning including all labour charges etc. complete OD

PLUMBING & SANITARY INSTALLATIONProviding and fixing white vitreous china pedestal type water closet ( European type WC pan) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P flush bend with fittings and CI brackets , 40 mm flush bend , overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets , cutting and making good the walls and floors wherever required W.C pan with ISI marked white solid plastic seat and lid(including baby friendly european type closet)17.3.2

Prioviding and fixing wash basin with C.I brackets, 15 mm C.P brass pillar taps, 32 mm C.P brass waste of standard pattern ,including painting of fittings, and brackets, cuttings, and making good the walls wherever required: white vitreous china flat back wash basin size 450 x 300mm with a single 15mm C.P brass pillar tap including cost of all materials & labour charges etc.complete(including baby friendly wash basin)17.7.3

Supplying & fixing steel sink (510x1040x25mm) including all fittings & other accessories including cost of all materials & labour charges etc.complete

Providing & fixing CP angle valve for basin mixer gyser points of approved quality conforming to IS 8931, 15mm nominal bore.17.10.1

Suppling and laying 25 mm PVC pipe with fittings such as tees, bents, elbows, check nuts etc. including excovation or cutting and making walls good and floors including cost of all materials, labour charges etc. complete OD

Suppling and laying 32 mm PVC pipe with fittings such as tees, bents, elbows, check nuts etc. including excovation or cutting and making walls good and floors including cost of all materials, labour charges etc. complete OD

Suppling and laying 110mm PVC pipe with fittings such as tees, bents, elbows, check nuts etc. including excovation or cutting and making walls good and floors including cost of all materials, labour charges etc. complete OD

Suppling and fixing water point [ long body tap (including sink tap) quarter thread ] with all connection and fittings including cost of all materials, labour charges etc. complete OD

Installation of PVC water tank 500 Lltrs ( Syntex double layer with Outlet valve & Delivery valve & all connections , fittings such as valve, bents, tees , elbows ) including cost of all materials, labour charges etc. complete OD

Suppling and fixing health faucet with ankle cok and other accessories including cost of all materials and labour charges etc.complete. OD

Providing 6" silt with CP gratings including cost of all materials and labour charges etc.complete. OD

Carpentry Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.9.76

Providing and fixing ISI marked 85x42 mm oxidised M.S. pull bolt lock conforming to IS: 7534 with necessary screws bolts, nut and washers etc. complete.9.64

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete: 250x10 mm.9.63.1

Powder coated M.S. butt hinges 100 mm X58 mmX1.9 mm 8100

Providing and fixing round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-charge 21.16.1

Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete. 9.68.1

Galvanised steel J or L hooks 8 mm dia 1023

Carpenter 1st class 0111

jayesh creatives pvt ltd