Rate contract for Electrical works in Different CT and PT Toilet Blocks under Swacchh Bharat Mission and other offices and building premises in all 7 zones AMC(Within the limit of Amount Rs.30.00 lacs)

(Technical Bid only) Office, Mezzanine Floor, “B”-Block,

Tender in Physical form Sardar Patel Bhavan, Danapith,

Ahmedabad-380001.

4 Tender Vol-I (Technical Bid on 03/03/2026, 04:05 pm onwards

only) Opening Date, Time Online Opening:- At the Office of

and Place Additional Chief Engineer(Electrical),

Light Department, 5th Floor, “C”-Block,

Sardar Patel Bhavan, Danapith,

Ahmedabad-380001.

Physical Opening:-At the Office of Tender

Officer, Central Record Office, Mezzanine

Floor, “B”-Block, Sardar Patel Bhavan,

Danapith, Ahmedabad - 380001 or at

the above said office.

MUNICIPAL COMMISSIONER

Ahmedabad Municipal Corporation

Sardar Patel Bhavan,Danapith

PRICE BID(FOR REFERENCE ONLY)

Tender for Rate contract for Electrical works in Different CT and PT Toilet Blocks under

Swacchh Bharat Mission and other offices and building premises in all 7 zones AMC.

(Within the limit of Amount Rs.30.00 lacs)

Sr No Item Description Unit Qty Rate in Rs.

Point wiring for Light / Fan / Bell / Primary Point

with 2-1.5 sq.mm & earth wire of 1.5 sq.mm(green)

both are of ISI marked 1.1 kv grade FRLS PVC

insulated multi strand copper wires upto max length

of 10 mt, in below type of pipe erected with 6A

Tissino Type ISI marked flush type switch / bell

1.0 push and accessories erected on Metal / PVC / Pt 1

Wooden Box covered with 3 mm thick

PC(Polycarbonate) / Acrylic / Laminated sheet. with

necessary Lamp holder / ceiling rose / H.D.

Connector as directed.

(e) in existing pipe erected flushed on wall/ceiling

Point wiring for independent PLUG with following

size mains earth wire of 1.5 sq.mm (green) both are

of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires upto 10 mt length, in

following below of pipe erected complete with ISI

2.0 marked 3 / 5 Pin socket and tissino type switch Pt 1

erected with earth continuity connection erected on

Metal / PVC / Wooden box covered with 3 mm thick

PC(Polycarbonate) / Acrylic / Laminated sheet.

(e) in existing pipe erected flushed on wall/ceiling

Same as Above for

[B] 6/16A Plug and 16 amp switch with 2-2.5 sq.

3.0 mm Cu. Mains from mcb db boards. Pt 1

(e) in existing pipe erected flushed on wall/ceiling

Point wiring for on board looped PLUG with tissino

type single pole ISI marked Switch and Socket

erected with necessary connections erected on

4.1 wooden / Metal / PVC Box covered with 3 mm thick Pt 1

PC(Polycarbonate) / Acrylic sheet for open /

concealed wiring for following size.

Same as Above for

Point wiring for Light / Bell with 2-1.5 sq.mm &

earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in below

type of pipe erected with 6A Modular type switch /

bell push & accessories and earth continuity of

following type, erected on PVC / Metallic / Wooden

box, single mounting base frame covered with

textured / metallic / white front plate modules

erected on / in wall / ceiling as per pipe erected,

with necessary Lamp holder / ceiling rose / H.D.

Connector as directed.

(e) in existing pipe erected flushed on wall / ceiling

complete Cat III

Point wiring for FAN with 2-1.5 sq.mm & earth wire

of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

Grade FRLS PVC insulated multi strand copper

wires up to 10 mtr length, in below type of pipe

erected with 6A Modular type switch and hum free

EME step type electronic fan regulator mounted and

accessories with earth continuity of following type

erected on PVC / Metallic / Wooden box, single

mounting base frame covered with textured /

metallic / white front plate modules erected on / in

wall / ceiling as per pipe erected. with necessary

ceiling rose / H.D. Connector as directed.

(e) in existing pipe erected flushed on wall/ceiling

complete Cat III

Point wiring for Individual Plug with earth wire of

1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug

erected on PVC / Metallic / Wooden box covered

7.1 with appropriate front plate modules erected on / in Pt. 1

wall / ceiling as per pipe erected with following type

of accessories.

[I] For 6A Plug and 6A switch with 2-1.5 sq.mm Cu.

wire from nearby switchboard / mcb db

(e) in existing pipe erected flushed on wall / ceiling

complete Cat III

Same as Above for

[II] For 16A Plug and 16A Switch with 2-2.5 sq.mm

7.2 Cu. wire from mcb db Pt. 1

(e) in existing pipe erected flushed on wall / ceiling

complete Cat III

Point wiring for on board Looped Plug with 6A

Modular type switch & 5 pin socket erected on PVC

/ Metallic / Wooden box, single mounting base

frame covered with textured / metallic / white front

plate modules erected on / in wall / ceiling with

following type accessories Cat III

Providing and erecting ISI mark Medium class RIGID

PVC PIPES of following size complete to be erected

on/in wall or ceiling erected with necessary PVC

9.1 fittings & Junction boxes fixed with adhesive Mtr. 1

solution & Clamps with following dia of pipes, in

approved manner as directed

Same as Above for

Providing and erecting Mains with 1.1 KV grade

FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected

concealed in / flushed on wall / ceiling, with 1.5 sq.

mm copper conductor FRLS PVC insulated stranded

wire of green colour for earth continuity of following

(A) with medium class Rigid PVC pipe and

(a) 2 wire 1.5 sq. mm

Same as Above for

(b) 2 wire 2.5 sq. mm

Same as Above for

(c) 3 wire 1.5 sq. mm

Same as Above for

d) 3 wire 2.5 sq. mm

Same as Above for

(e) 4 wire 1.5 sq. mm

Same as Above for

(f) 4 wire 2.5 sq. mm

providing and erecting Mains with 1.1 KV grade

FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected

in / on wall / ceiling with 2.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of

green colour for earth continuity of following size

(E) in existing pipe

(a) 2 wire 4 sq. mm

Same as Above for

(b) 2 wire 6 sq. mm

providing and erecting Mains with ISI marked,

1.5KV grade electrolyte multistranded, annealed

copper conductor with heat resistant PVC insulated

conforms to IS 694, IEC - 227 erected in existing

12.1 pipe of following size(Specifically for control panel, Mtr 1

relays, power switchgears, motor starters & control

wiring) with required size of copper lugs, nuts and

bolts if required.

(d) One wire 4.00 sq. mm

Same as Above for

(e) One wire 6.00 sq. mm

Same as Above for

(f) One wire 10.00 sq. mm

Same as Above for

(g) One wire 16.00 sq. mm

Same as Above for

(h) One wire 25.00 sq. mm

Same as Above for

(i) One wire 35.00 sq. mm

Same as Above for

(j) One wire 50.00 sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI

armoured cable multistrand / Solid Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of

following size of cables

(c) 4 core 10.0 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI

armoured cable multistrand Aluminium conductor

14.1 for 1.1 KV. to be laid on wall with necessary clamps Mtr 1

or in existing trench / pipe of following size of cables

(A) 4 core 16 Sq. mm

Same as Above for

(B) 4 core 25 Sq. mm

Same as Above for

(C) 4 core 35 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand Copper conductor for

1.1 KV. to be laid on wall with necessary clamps or

in existing trench / pipe at road crossing or floor

of following size of cables.

(A) 3 1/2 core 25 Sq. mm(10 Sq. mm 1/2 core)

Same as Above for

(B) 3 1/2 core 35 Sq. mm(16 Sq. mm 1/2 core)

SITC of 14.2 mm dia 3 mtr long Earth electrode of

High tensile steel electrode with 250 micron copper

bonding & 1 bag of Carbon fill Based environment

friendly backfill tested as per IEC 62561-7 in NABL

16.0 accredited Laboratory and suitable stainless Steel 1

double sided clamp. Eco Friendly rust proof heavy

duty weather proof Polyethylene Earth Pit Chamber

with following dimensions :254 mm dia (top),

mm dia (bottom) & 260 mm (height).

Supplying and erecting LED indoor fittings with

LEDs of wattage 0.2 Watt to 0.5 Watt assembled on

single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder

coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with

company mark / name

17.0 160V to 270V, Power Factor more than 0.9, THD < Ea. 1

15 %, CCT 3000 K to 6500K, Luminaire efficiency >

85 lumens/watt, LED driver efficiency > 85% (fitting

required LM-79 & LM-80 Certificates) (NOTE: Below

description have shown ranges of Wattage capacity

of LED fittings. The Engineer incharge may select

any wattage capacity between the ranges shown.)

(A) TubeLight with integral driver (iii) 18-20 Watts,

Surge - 2KV, IP-20, conventional 4 feet Cat-lll

Supplying and erecting LED indoor fittings with

LEDs of wattage 0.2 Watt to 0.5 Watt assembled on

single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder

coated and high U.V. & corrosion resistance with

diffuser housed in alluminium casted body with

company mark / name

160V to 270V, Power Factor more than 0.9, THD <

Luminaire efficiency > 85 lumens/watt, LED driver

efficiency > 85% (fitting required LM-79 & LM-80

Certificates) (NOTE: Below description have shown

ranges of Wattage capacity of LED fittings. The

Engineer incharge may select any wattage capacity

between the ranges shown.)

(A) Square / Circular shaped Surface / Recessed

Mount Downlight with provision for spring loaded

mounting clips complete. IP20

(i) 5-9 watts,Surge-2 KV Cat-lll

Same as Above for

(ii) 11-15 watts, Surge-2 KV Cat-lll

Same as Above for

(iii) 16-20 watts, Surge-2 KV Cat-lll

Same as Above for

(iv) 22-24 watts, Surge-2 KV Cat-lll

Same as Above for

(B) LED Panel Light with provision for Plane front

18.5 frame with translucent cover fixed to housing Ea. 1

(iv) 18 to 20 watts, 8" x 8", Surge- 2 KV Cat-lll

Same as Above for

(v) 24 watts, 12" x 12" , Surge-2 KV Cat-lll

Same as Above for

(vi) 36 watts, 24" x 24", Surge- 2 KV Cat-lll

Same as Above for

18.8 (vii) from 45 to 48 watts, 24" x 24", Surge-2 KV Cat- Ea. 1

Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of

Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free

High pressure die cast aluminum housing with

smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics /

lenses, with toughened glass with company mark /

name engraved or embossed 160 to 270 V, Power

Factor more than 0.95, THD < 10%, CCT 3000K to

19.1 5700K, Uniformity ratio > 0.45, Luminaire efficiency E.a. 1

> 100 lumens/watt. LED driver efficiency > 85%.

(fittings required LM-79 & LM-80 certificates) (NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings. The Engineer incharge may

select any wattage capacity between the ranges

(B) Flood Light (IP-65), Surge protection-4KV integral

and, Light must have 440VAC line supply with over-

voltage protection.

(iv) Above 90W to120W Cat.III

Same as Above for

(vi) above 160 to 200 watts Cat.III

providing and erecting Miniature circuit breaker

single pole 6A to 25A suitable to operate on 240 V

20.0 A.C. system and having breaking capacity 10 KA to Ea. 1

be erected in existing box. confirming to IS

8828/1996 with ISI Mark Cat.III

Providing & erecting 240 V MCB double pole switch

for motor & inductive load(C-Curve) having 10 KA

breaking capacity & confirms to IS : 8828 in existing

box having following capacity(a) 6 to 32 Amp. Cat.III

Same as Above for

(b) 40 Amp. Cat.III

Providing & erecting 415 V MCB Four Pole for Motor

& Inductive Load (C Curve) having 10KA breaking

22.1 capacity & confirms to IS :8828 in existing box Ea. 1

having following capacity

(a) 6 to 32 Amp. Cat-lll

Same as Above for

(b) 40 Amp. Cat.III

Same as Above for

(b) 63 Amp. Cat.III

Providing & erecting 415 V MCB three Pole for

Motor & Inductive Load (C Curve) having 10KA

23.1 breaking capacity & confirms to IS :8828 in existing Ea. 1

box having following capacity

(a) 6 to 32 Amp. Cat-lll

Same as Above for

(b) 40 Amp. Cat.III

Same as Above for

(b) 63 Amp. Cat.III

Providing and erecting Sheet Steel powder coated

MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN

rail, confirming to IS 8623-1&3, and iec61439-1&3

without MCB to house appropriate nos. of MCBs

(The DBs should be used of same company of MCB

to be used) suitable for

(A) single phase incoming and horizontal single

phase outgoing (IP-43

Same as Above for

Same as Above for

Same as Above for

(B) three phase incoming and single phase

horizontal type outgoing Per phase isolation type

(b) sheet steel double door

Same as Above for

Same as Above for

Same as Above for

providing and erecting Approved make RCCBs

conforming to IS: 12640 and having sensitivity of

mA and Short Circuit withstand capacity of 10 KA

and suitable for operation on single phase

25.1 V,50Hz. having characteristic of quick action & Ea. 1

tripping with all advance feature & do not

incorporate any electronic component. for following

Max. rating erected as directed(i) 25 Amps.DP Cat.

Same as Above for

(ii) 40 Amps. DP Cat. III

Same as Above for

(iii) 63Amps. DP Cat. III

Providing and erecting Approved make RCCBs

conforming to IS: 12640 and having sensitivity of

mA and Short Circuit withstand capacity of 10 KA

and suitable for operation on 3 phase and neutral

415V, 50Hz. having characteristic of quick action &

tripping with all advance feature & do not

incorporate any electronic component for following

Max. rating erected as directed.

(i) 25 Amps. FP Cat-lll

Same as Above for

(ii) 40 Amps. FP Cat. III

Same as Above for

(iii) 63 Amps. FP Cat. III

Same as Above for

(iv) 100 Amps. FP (100 mA Sensitivity) Cat. III

Providing and erecting busbar chamber confirming

to IS-375 fabricated from 16 G.M.S. sheet, dust &

vermin proof having hinged door with rubber gasket

and necessary busbar supports with Aluminium

busbar having current density not more than

Amp. / sq.mm (Rated current / cross section area)

duly wrapped with colour insulation tape for phase

sequence, three phase & neutral each Suitable for

following current capacity with necessary painting

mounted on wall or pedestal frame of required size

with necessary connections.

(A) Suitable for 63/100 Amp. capacity

Providing and erecting busbar chamber confirming

to IS-375 fabricated from 16 G.M.S. sheet, dust &

vermin proof having hinged door with rubber gasket

and necessary busbar supports with COPPER

busbar having current density not more than

Amp. / sq.mm (Rated current / cross section area)

duly wrapped with colour insulation tape for phase

sequence, three phase & neutral each suitable for

following current capacity with necessary painting

mounted on wall or pedestal frame of required size

with necessary connections.(A) Suitable for 63/100

Supplying & erecting fan hook box of 10 mm M.S.

round bar bounded to the RCC bars up to 50 mm

29.0 length each side and pierced through a 16 Gauge Ea. 1

M.S. box / Heavy Duty PVC box complete erected

concealed in Ceiling with necessary finishing.

Supplying & erecting approved make low noise

decorative exhaust fan having size 200mm with

1350 RPM with square frame ABS body with inbuilt

lowers & square frame. 200mm with 1350RPM Cat.II

Supplying & erecting single phase approved make

industrial exhaust fan suitable for medium duty ring

mounted low noise operation suitable for medium

duty having following dia size and maximum speed

[A] 305 mm dia 900 RPM Cat- II

Supplying and erecting approved make Bracket fan

of 230 volt, A.C. 50 Cy/s., 400/450 mm sweep

complete erected on wall or with lead Cores and

connections complete. Cat-ll

Supplying and erecting approved make pedestal fan

A.C. 230V. 50 Cy/s. 400 mm sweep oscillating, type

33.0 and adjustable, height complete with guard Ea. 1

regulator, & standard lead flexible wires and plug

Providing and erecting Approved make Ceiling fan

with double ball bearing ISI mark with condenser

A.C. 23OV.50 c/s.1200 mm. sweep complete,

canopy erected on existing hook or clamp with

earthing. [Make shall be approved by Engineer in

Supplying and erecting 19/20 mm. nominal bore

Medium Class M.S. Pipe down rod erected duly

painted for fan complete with proper insulation

without leakage and earthing.

Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking

capacity ICU of 25 KA. at 415 V,having normal

current rating up to 25 A to 100A. with Fixed

36.0 thermal & magnetic release suitable to work on A.C. Ea. 1

supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in

existing 16 G.M.S. housing. ICS=100% of ICU only

Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking

capacity ICU of 35 KA. at 415 V. having normal

current rating 125A. with Fixed thermal & magnetic

release suitable to work on A.C.supply 50 c/s. with

all internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking

capacity ICU of 35 KA. at 415 V. having Normal

current rating 200A.with variable Thermal &

magnetic release suitable to work on A.C.supply

c/s. with all internal connections, spreader tinned

copper & complete erected in existing

G.M.S.housing. ICS=100% of ICU only CatIII

Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking

capacity ICU of 35 KA. and above at 415 V. having

normal current rating 250A. with variable thermal

& magnetic release suitable to work on A.C. supply

50 c/s. with all internal connections, spreader

tinned copper & complete erected in existing

G.M.S. housing. ICS=100% of ICU only Cat III

Disconnecting the cable connection and Providing

straight joint with PVC mould using heat shrink

/cast resin type epoxy compound Insulating

material and making the joint complete using

40.1 necessary in line connectors, hardener, earth Ea. 1

continuity connection, spacers etc. and reconnecting

the same & ensure the joint resistance within the

limits as per IS.

(A) up to 25 Sq mm Cable

Same as Above for

(B) 35 to 95 Sq. mm cable.

providng and erecting Approved make single phase

electronic energy meter rating 5A/20A/40A based

on ASIC (Application Specific integral circuit) digital

technology with accuracy Class-I, temper proof, free

from effect of external magnetic field with phase,

earth, reverse and impulse indications, 6 digit

electro-mechanical counter suitable to work on

V to 300V, 45 - 55 Hz., housed in robust enclosure

complete to be erected as directed with 3 year

replacement guarantee. Cat. III

providng and erecting Approved make energy meter

3 phase 4 wire unbalanced load rating, 10A to

Amp. based on ASIC(Application specific Integral

Circuits) digital technology with accuracy Class - 1

temper proof, free from effect of external magnetic

field with 3 phase indication, earth & impulse

indication, 6 digit electro mechanical impulse

counter, suitable work on 120 V to 300V per phase

45-55 HZ, housed in robust enclosure with erection

as directed. Cat-lll

Providing following type of Modular Type Accessories

mounted with PVC / metallic / Wooden box, single

mounting base frame covered with textured /

43.1 metallic / white front plate, modules erected with Ea. 1

necessary connections as per site situation directed

by Engineer In charge.

(1) One No. SP 6 Amp. Cat.III

43.2 (2) One No 5 pin plug Cat.III Ea. 1

(5) Electronic hum free four or more steps EME fan

regulator cat.III

43.4 (7) Blank Plate Single Cat-III Ea. 1

43.5 (9) 16 Amp. SP one way Switch Cat.III Ea. 1

43.6 (10) 6/16Amp. Universal Socket Cat.III Ea. 1

Providing & Erecting following Shockproof tissino

type accessories erected on 3 mm thick PC

44.1 (Polycarbonate) sheet in PVC / Metal / Wooden Box Ea. 1

erected on wall / ceiling.

(1) One no Single pole 6 A Switch / Bell push

44.2 (2) One no 3/5 pin 6 A Socket Ea. 1

44.3 (3) One no Single pole 16 A Switch Ea. 1

44.4 (4) One no 6/16 A Universal Socket Ea. 1

(14) Electronic Hum free EME Socket Type Steps

Providing and erecting Annealed bare Copper wire

Supplying and erecting led lamps with following

wattage capacity of 220 to 240 voltage, minimum

15000 burning hours life, 500 V in built-surge

protection,Polycarbonate diffuser, mounting suitable

for E14 / E27 / B22 lamp holders, pf >= 0.5 (A) LED

Lamps integral type, with PC diffuser suitable LAMP

(iii) 10 to 15 watts Cat-III

Same as Above for-

(iv) 16 to 20 watts Cat-III

Supplying and Installation of Approved make

Integrated LED Solar light fitting comprising in built

Poly crystalline solar panel,Lithium-ion 3.7 V

battery, LED CRI Greater than 70, CCT-6500K,

lum/watt all housed in Extruded Aluminium

body,with motion sensor & auto on -off device

erected on existing pole with following specifications.

(A) 6 watt LED light, with 7 W Solar panel, 3.7 V

13000 to 15000 mAh battery, 450 lm luminus flux,

suitable for mount on 3 mtr height pole.

Same as Above for-

(B) 12 watt LED light, with 15 W Solar panel, 3.7 V

26000 to 28000 mAh battery, 850-900 lm luminus

flux, suitable for mount on 3.5 to 4 mtr height pole.

Same as Above for-

(C) 18 watt LED light, with 22 W Solar panel, 3.7 V

47.3 39500 to 40500 mAh battery, 1250-1350 lm Ea. 1

luminus flux,suitable for mount on 3.5 to 4 mtr

Providing , erecting , fabricating the M.S. structure

as per requirement on site incorporating proper size

of M.S. angles,square,round, flats, bars, channels,

sections complete with cutting, welding, grinding &

finishing duly painted with one coat of red oxide

with erection on site as per direction of engineer in

charge with necessary grouting, cementing,

plastering & finishing complete.

Estimated Amount in Rs.

Final Amount(Including GST) in Rs.

I/We am/are willing to carry out work at ____________% above or ____________% Below the

estimated cost mentioned above.

NOTE:- The Quoted Rate Shall be Inclusive of all taxes.

Signature of the Tenderer Addl. Chief Engineer

Name : (Electrical)

Company’s seal Date :