CLEANING OF UNDERGROUND SUMP, FILTER BED, OVER HEAD TANK AND ALLIED WORKS UNDER GE CLEMENT TOWN

Amount

M&L for cleaning of internal surface of ground level water reservoir 50,000 Gallons capacity by removing silt, all scales by scraping & cleaning, washing with water and make the surface neat and clean, and applying two coats of lime wash on internal and external surface, writing date of cleaning and capacity of tank with synthetic enamel paint complete all as specified and directed.

M&L for cleaning of internal surface of ground level water reservoir 1,50,000 Gallons capacity (04 Nos), 3.8 m deep and size 19.4m X 12.7 m by removing silt, all scales by scraping & cleaning, washing with water and make the surface neat and clean, and applying two coats of lime wash on internal surface, writing date of cleaning and capacity of tank with synthetic enamel paint complete all as specified and directed.

Cleaning of internal surface of RCC overhead tank of 50,000 gallons capacity on 15.2 m staging by removing silt, all scales by scraping with steel wire brush, washing with water and writing date of cleaning and capacity of tank with synthetic enamel paint and applying two coats of lime wash on internal surface of tank complete all as specified and directed.

All as item No. 03 above but of 1,00,000 gallons capacity on 15.2m staging complete all as specified and directed.

All as item No. 03 above but of 1,50,000 gallons capacity on 18m staging complete all as specified and directed.

All as item No. 03 above but of 3,00,000 gallons capacity on 21m staging complete all as specified and directed.

All as item No. 03 above but of 20,000 gallons capacity on 12.2 m to 24 mtr staging complete all as specified and directed.

All as item No. 03 above but of 25,000 gallons capacity on 15m to 24 m staging complete all as specified and directed.

All as item No. 03 above but of 10,000 gallons capacity on under ground make-up tank complete all as specified and directed. (Note :- Cleaning process as under for item No. 1 to 9 :- (i) Cleaning of tank shall be done through a mechanize water cleaning system. (ii) Dewatering of over head tank by drain out pipe (iii) Mechanized removel of all remaining dirty water by high capacity pump set. (iv) Removel of sludge by vacum operated pump. (v) cleaning of wall,ceiling and bottem of tank by high pressure rotary jet 120 bars pressure (vi) Removal of all dirty particles by Industrial Wet Vacuume cleaner leaving the tank 99.9% physically cleaned. (vii) Sterilization of tank by eco- Friendly biodegradable and highly effective anti bacterial non toxic agent approved By NTC (National Toxicology Center) against all pathogens agent of tank clean. (viii) All the sludge material/Fungus removed from the underground sump/semi underground sump and over head tank will be removed outside the defence land from the site. (ix) All T & P required for the cleaning of tank/Sumps will be arrange by the contractor. (x) The work will be got executed from the reputed specialized water tank cleaner as approved by GE. (xi) Writing with bold letters such as "TANK CLEANED ON ----- --- ---2022/23" and next due date --- --- 2023 cleaning of the tank by synthetic enamel paint. (xii) The cost of the same shall be deemed included in the respective items.)

M & L for cleaning on roof top, disconnection of delivery pipe, float valve of service tank, opening up of drain plug, cleaning thoroughly by brushing, internal star faces, removing all scale and dirt, flushing out with fresh water, connecting back in position writing with white bold letters with synthetic enamel paint such as “CLEANED ON’ – -- -- 2023” complete all as specified and directed. (i) For masonary/PVC tank (for solar purpose) Exc100 litres and not exceeding 250 litrs complete all as specified and directed.

All as item No. 10 above but for masonary/PVC tank (for solar purpose) Exc250 litres and not exceeding 500 litrs complete all as specified and directed.

All as item No. 10 above but for masonary/PVC tank (for solar purpose) Exc500 litres and not exceeding 1000 litrs complete all as specified and directed.

All as item No. 10 above but for masonary/PVC tank (for solar purpose) Exc1000 litres and not exceeding 2000 litrs complete all as specified and directed.

Excavation in trenches in any type of soil not exceeding 1.5 mtr wide and not exc.1.5 mtr in depth for taking/laying of CI/GI pipe and getting out including forming bottom surface etc. complete all as specified and directed.

Returning filling in same earth in trenches including spreading leveling watering and well ramming in layers not. Exc. 25cm thick any type of soil after the pipe laid complete all as specified and directed.

Removing of excavated soil n. exc. 50m and depositing where directed at a level n.exc. 1.5 m above the starting points complete all as specified and directed.

Taking out 20mm bore unserviceable rusted PPR/ steel water tubing and connection including cleaning for refixing complete all as specified and directed.

All as per item No. 17 above but for 25mm dia of pipe complete all as specified and directed.

All as per item No. 17 above but for 40mm dia of pipe complete all as specified and directed.

All as per item No. 17 above but for 50mm dia of pipe complete all as specified and directed.

All as per item No. 17 above but for 80mm dia of pipe complete all as specified and directed.

All as per item No. 17 above but for 100mm dia of pipe complete all as specified and directed.

All as per item No. 17 above but for 150mm dia of pipe complete all as specified and directed.

Refixing old serviceable 20mm bore steel tubing and connections in any length in new or old position (walls, ceilings, floors, trenches etc. complete all as specified and directed.

All as per item No. 24 above but for 25mm dia of pipe complete all as specified and directed.

All as per item No. 24 above but for 40mm dia of pipe complete all as specified and directed.

All as per item No. 24 above but for 50mm dia of pipe complete all as specified and directed.

All as per item No. 24 above but for 80mm dia of pipe complete all as specified and directed.

All as per item No. 24 above but for 100mm dia of pipe complete all as specified and directed.

All as per item No. 24 above but for 150mm dia of pipe complete all as specified and directed.

Supply and laying in trenches/wall/floors 20mm bore GI tube medium grade including all required fittings complete all as specified & directed.

All as per item No. 31 above but for 25mm dia of pipe complete all as specified and directed.

All as per item No. 31 above but for 40mm dia of pipe complete all as specified and directed.

All as per item No. 31 above but for 50mm dia of pipe complete all as specified and directed.

All as per item No. 31 above but for 80mm dia of pipe complete all as specified and directed.

All as per item No. 31 above but for 100mm dia of pipe complete all as specified and directed.

All as per item No. 31 above but for 150mm dia of pipe complete all as specified and directed.

Cutting to existing 50mm dia GI main line for taking new branch line complete all as specified and directed.

All as per item No. 38 above but for 80mm dia complete all as specified and directed.

All as per item No. 38 above but for 100mm dia complete all as specified and directed.

All as per item No. 38 above but for 150mm dia complete all as specified and directed.

Screwing existing 50mm dia steel tubing for alterations or additions (or lengthening screw on pipe to form connector complete all as specified and directed.

All as per item No. 42 above but for 80mm dia complete all as specified and directed.

All as per item No. 42 above but for 100mm dia complete all as specified and directed.

All as per item No. 42 above but for 150mm dia complete all as specified and directed.

S&F in repair of new Float valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe suitable for 15mm bore complete all as specified and directed. Make-Prayag/Shakti or equivalent of ISI marked.

All as per item No- 46 above but 20mm bore.

All as per item No- 46 above but 25mm bore.

S&F in repair 15mm dia gun metal Glove valve/gate valve with iron wheel head screwed both ends for GI pipe and fixed complete all as specified and directed.

All as per item No. 49 above but for 20mm dia complete all as specified and directed.

All as per item No. 49 above but for 25mm dia complete all as specified and directed.

All as per item No. 49 above but for 40mm dia complete all as specified and directed.

All as per item No. 49 above but for 50mm dia complete all as specified and directed.

Supply only nuts, bolts & washers off size as required complete all as specified and directed.

Supply only rubber sheet 3 mm thick complete all as specified and directed.

Supply only rubber sheet 6 mm thick complete all as specified and directed.

Supply only Gland packing of sizes 8 mm to 12.5 mm thick complete all as specified and directed.

Supply only lead pig complete all as specified and directed.

Supply only lead wool complete all as specified and directed.

S&F in repair of CI/DI/MS double flanged 50mm dia bore Non-return valve, class 'B', High pressure PN 1.6 conforming to ISI marked, including bolts, nuts, washer and rubber packing complete all as specified and directed of the following size :- Make : Kirloskar, BVI, BIR.

All as per item No. 60 above but 80mm dia bore complete all as specified and directed.

All as per item No. 60 above but 100mm dia bore complete all as specified and directed.

All as per item No. 60 above but 150mm dia bore complete all as specified and directed.

All as per item No. 60 above but 200mm dia bore complete all as specified and directed.

S&F in repair 80mm dia dead plate of flange pipe of 6 mm thick sheet with made out suitalbe holes as required complete all as specified and directed.

All as per item No. 65 above but 100mm dia complete all as specified and directed.

All as per item No. 65 above but 150mm dia complete all as specified and directed.

All as per item No. 65 above but 200mm dia complete all as specified and directed.

M&L for run lead joints except pipes for the 80mm dia of pipe line including taking out u/s joint carefully complete all as specified and directed.

All as per item No. 69 above but 100mm dia of pipe complete all as specified and directed.

All as per item No. 69 above but 150mm dia of pipe complete all as specified and directed.

All as per item No. 69 above but 200mm dia of pipe complete all as specified and directed.

S&F in repair 100mm dia MS/GI detachable 'D'' joints complete with jointing material, nut, bolts, gasket etc complete all as specified and directed.

All as per item No. 73 above but 150mm dia complete all as specified and directed.

All as per item No. 73 above but 200mm dia complete all as specified and directed.

All as per item No. 73 above but 300mm dia complete all as specified and directed.

All as per item No. 73 above but 350mm dia complete all as specified and directed.

S&F in repair 50mm dia HDPE detachable 'D'' joints complete with jointing material, nut, bolts, gasket etc complete all as specified and directed.

All as per item No. 78 above but 80mm dia complete all as specified and directed.

All as per item No. 78 above but 100mm dia complete all as specified and directed.

S&F in repair 100mm dia MJ Collar complete with jointing material, nut, bolts, gasket etc complete all as specified and directed.

All as per item No. 81 above but 150mm dia complete all as specified and directed.

All as per item No. 81 above but 200mm dia complete all as specified and directed.

Taking out the defective parts of 75 HP capacity submersible motor, 3 phase, 440 Volts and rewinding with super enamelled copper conductor of suitable as per existing size and gauge including varnishing, drying, cleaning of slots, repair to any damage slot, metling to shaft for fixing of bearing and other required work for smooth functioning of motor, testing complete all as specified and directed.

All as per item No. 84 above but 60 HP capacity complete all as specified and directed.

All as per item No. 84 above but 41/40 HP capacity complete all as specified and directed.

All as per item No. 84 above but 12.50 HP capacity complete all as specified and directed.

All as per item No. 84 above but 5 HP capacity complete all as specified and directed.

Opening the submerssible pump of capacity 75 HP cap.6 stages,1500 LPM, 120 mtr head from the motor, transporting to workshop, dismantling of Submersible pump set,tracing out the defects,and taking out the u/s parts from the pump set, metling, grinding to bring the set in its original position, replacement of neck ring, key set, brass bushes, adjustment nut, thrust plate, coupling bushes, GM ball bush, katcher key set etc., assembling the pump set and testing complete all as specified and directed.

All as per item No. 89 above but 60 HP cap.6 stages,1500 LPM, 108 mtr head capacity complete all as specified and directed.

All as per item No. 89 above but 41/40 HP capacity complete all as specified and directed.

All as per item No. 89 above but 12.50 HP capacity complete all as specified and directed.

All as per item No. 89 above but 5 HP capacity complete all as specified and directed.

Opening, dismantling, decoupling and taking out defective induction motor of capacity 150 HP from foundation / base frame, transporting to workshop for repair & transporting back at site after repair and refixing the same on its position, recoupling, reconnection, testing commissioning complete all as specified and directed. Note:- Repair work shall be measured and paid separately under respective item of Sch 'A'.

All as per item No. 94 above but 40/50 HP capacity complete all as specified and directed.

All as per item No. 94 above but 25/30 HP capacity complete all as specified and directed.

All as per item No. 94 above but 5 HP capacity complete all as specified and directed.

Taking out the defective parts of 150 HP capacity induction motor/turbine motor, 3 phase, 440 Volts and rewinding with super enamelled copper conductor of suitable as per existing size and gauge including varnishing, drying, cleaning of slots, repair to any damage slot, metling to shaft for fixing of bearing and other required work for smooth functioning of motor, testing complete all as specified and directed.

All as per item No. 98 above but 40/50 HP capacity complete all as specified and directed.

All as per item No. 98 above but 25/30 HP capacity complete all as specified and directed.

All as per item No. 98 above but 5 HP capacity complete all as specified and directed.

Opening of 150 HP capacity centrifugal pump set from the base, transporting to work shop, trace out defects and taking out the u/s parts from the pump set, metling, grinding, lathing work as required to make as per original shape and size and fixing the new parts as required complete all as specified and directed. Note : Spares will be measured and paid separatly.

All as per item No. 102 above but 40/50 HP capacity complete all as specified and directed.

All as per item No. 102 above but 25/30 HP capacity complete all as specified and directed.

All as per item No. 102 above but 5 HP capacity complete all as specified and directed.

S&F in repair of Ball Bearing No. 6309/3309 for 150 HP Pump complete all as specified and directed.

S&F in repair of ball Bearing No. 6308/6309 for 40/50 HP Pump complete all as specified and directed.

S&F in repair of ball Bearing No. N321/ for 150 HP Motor complete all as specified and directed.

S&F in repair of ball Bearing No. N319 for 150 HP Motor complete all as specified and directed.

S&F in repair of ball bearing No 6311/6312 for 40/50 HP Motor complete all as specified and directed.

Repair to foot valve of 200mm dia suction line by means disconnection by opening of nut bolts etc and taking out from under ground Sump and refixing the same affter replacement of leather/Neoprane/rubber sheet including lightening of nut bolts etc. complete all as specified and directed.

All as per item No- 111 above but 150mm dia bore complete all as specified and directed.

All as per item No- 111 above but 100mm dia bore complete all as specified and directed.

S&F in repair of Cast Iron industrial type water meter, double flanged, class 'B', High pressure PN 1.6, ISI marked, of 150mm dia bore pipe for existing Tube well, including bolts, nuts, washer and rubber packing complete all as specified and directed of the following size :- Make : Kranti, Belanto, BIR.

All as per item No- 114 above but 80mm dia bore.

All as per item No- 114 above but 50mm dia bore.

Cutting vegetation and surface dressing not exceeding 15 cm deep including removing the materials to a distance not-exc 60 mtr complete all as specified and directed.

Opening, dismantling, decoupling and taking out defective parts of water pressure pump set (Pump + Motor + saner) of capacity 1.0 HP from the base, transporting to work shop, trace out defects and taking out and replace of the u/s parts from the pressure pump set, metling, grinding, lathing work as required to make as per original shape and size and fixing the new parts as required complete all as specified and directed.

S&F in repair contactor ML 50 KW, 415 volts, 150 amps fixed in starter suitable for 75 HP motor complete all as specified and directed. Make:-L&T /BCH/Scheinder.

Lifting of submerssible pump set of any cap from borewell carefully with coloumn pipe of size upto 150/200 mm dia flanged/socketed MS/GI,3 mtr each length (20 to 30 Nos of pipe) along with existing submerssible electric cable and shifting the pipe aside for reuse complete all as specified and directed.

Lowering of submerssible pump set of any cap into the borewell carefully with coloumn pipe of size upto 150/200 mm dia flanged/socketed MS/GI,3 mtr each length( 20 to 30 Nos of pipe),along with existing submerssible electric cable binding with GI/Al wire including making joint to submerssible cable complete all as specified and directed. Note: - Rubber gasket, jointing material, nut,bolts,washers shall be included in the quoted rate.

NOTES :- 1. For the items for which specifications not mentioned any where in the tender, the BIS specifications shall be followed.

DOON DIESEL SALES AND SERVICE

venus engineers

Neev Enterprises

M/s Anamika Enterprises

Meher enterprises

M/s Vinod Singh Negi

M R Taders

ANAND SERVICES

Bhanu Prakash

Ansh Enterprises

G S CONSTRUCTIONS