Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
Tender Value
₹44.5 Cr
EMD Value
₹44.5 L
Closing Date
25 Nov 2026, 6:00 pm2d left
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
Office Of The Executive Engineer, C.P. No.4, Block No.3, E-2 Wing, 5th Floor, Karmyogi Bhavan, Sector-10/A , Gandhinagar.
Construction of Samras Girls Hostel at Sector-15, Gandhinagar
360794
16 of 2026-27
Open
Civil - All
Works
Gandhinagar
8 documents required · 8 mandatory
₹18,000
Executive Engineer, Capital Project Div. No.4, Gandhinagar
₹44.5 L
25 Nov 2026
29 Oct 2026
25 Nov 2026
29 Oct 2026
18 Nov 2026
29 Oct 2026
90 days
No figures
1 Excavation for foundation Upto 1.50 m depth 6260.00 Cum 123.13
including sorting out and stacking of the useful
materials and disposing off the excavated stuff up to
All lead. (A) loose or soft soil.
2 Excavation for foundation from depth 1.50 m to 3.00 3669.00 Cum 170.50
m including sorting out and stacking of the useful
materials and disposing off the excavated stuff up to
All lead. (A) Dense or Hard soil.
3 Excavation for foundation from depth 3.00 m to 5.00 1199.00 Cum 300.02
m including sorting out and stacking of the useful
materials and disposing off the excavated stuff up to
All lead. (A) Hard murrum.
4 Filling available excavated Earth (Excluding Rock) in 5599.28 Cum 136.92
trench plinthside of foundation etc. in layer not
exceeding 20 cm in depth consolidation each
deposited layer by ramming and watering etc.
5 Filling in foundation and plinth with murrum or 954.00 Cum 277.14
watering, ramming and consolidating etc. complete.
6 Filling in plinth with sand under floors including 478.00 Cum 481.70
watering, ramming consolidating and dressing etc.
7 Anti-Termite System:Providing and laying of 2368.00 Sqm 134.33
permanent piping technology anti-termite treatment
before flooring work by installing LLDP (Low linear
density polyethylene) tube of 8 mm O.D. & 6.4 mm 1.D.
with inbuilt pressure compensation chip every 30 cm
interval in the tube, having working pressure of
Kg/cm2 and release rate of 1.9 Itr/hour fixed by P-
clips and nails. The LLDP pipe shall be installed at the
entire periphery of the building and at internal
network of building at a depth of 20 to 200 mm under
floor at every 2 to 3 mtr. c/c distance (adjusted as per
building layout ) & Ends of loop pass through a PVC
elbow of minimum 32 mm ID at junction box of wall
and floor level, entering into a steel reinforced
grooved flexible pipe of minimum 22 mm ID leading
into junction box and the loops shall terminate in
junction boxes & test every junction during injecting
chemicals for termite control treatment. The anti
termite chemical Imidacloprid 30.5% SC mix as per IS-
6313 (part III) shall be injected by the pressure pump
diluted with water @ 10.5 ml/5 ltr of water at the rate
of 2 Kg/sq.cm @ 5 Ltr/SMT. The contractor shall
submit approved line plan for piping system and
Item Rate In
Description of Item Quantity Unit Amount
No figures
8 Providing and laying in position Ready Mixed M-150 1312.80 Cum 4645.80
grade concrete for reinforced cement concrete work in
Foundations & Plinth, using cement content as per
approved Design Mix manufactured in fully automatic
batching plant established on site and transported to
site of work in transit mixer having continuous
agitated mixer, manufactured as per mix design of
specified grade for reinforced cement concrete work
including pumping of R.M.C. from transit mixer to site
of laying, excluding the cost of reinforcement and
including cost of centering. shuttering, formwork
finishing and admixtures in recommended
proportions as per IS : 9103 to accelerate/ retard
setting of concrete, improve workability without
impairing strength and durability as per direction of
the Engineer -In - Charge. Without Fly Ash (Min
cement level as per latest IS 456 shall be maintained)
9 Extra for concreting in grade M350 instead of M250 1687.00 Cumt 273.57
including cost of cement, labour etc. complete.
10 Extra for concreting in grade M300 instead of M250 260.00 Cumt 182.38
including cost of cement, labour etc. complete.
11 Providing and laying in position Ready Mixed M-250 7635.50 Cum 6848.81
grade concrete using cement content as per approved
Design Mix manufactured in fully automatic batching
plant established on site and transported to site of
work in transit mixer having continuous agitated
mixer, manufactured as per mix design of specified
grade for reinforced cement concrete work including
pumping of R.M.C. from transit mixer to site of laying,
excluding the cost of reinforcement and including cost
of centering. shuttering, formwork finishing and
admixtures in recommended proportions as per IS :
9103 to accelerate/ retard setting of concrete,
improve workability without impairing strength and
durability as per direction of the Engineer -In - Charge.
Without Fly Ash (Min cement level as per latest IS
shall be maintained) for all RCC elements like
foundation, slabs, beams, plinth beams, coping,
columns, walls chhajja, and stair cases etc at all floor
level from below plinth and above plinth level.
Item Rate In
Description of Item Quantity Unit Amount
No figures
12 Providing and laying in position Ready Mixed M-200 381.00 Cum 5071.21
grade concrete using cement content as per approved
Design Mix manufactured in fully automatic batching
plant established on site and transported to site of
work in transit mixer having continuous agitated
mixer, manufactured as per mix design of specified
grade for reinforced cement concrete work including
pumping of R.M.C. from transit mixer to site of laying,
excluding the cost of reinforcement and including cost
of centering. shuttering, formwork finishing and
admixtures in recommended proportions as per IS :
9103 to accelerate/ retard setting of concrete,
improve workability without impairing strength and
durability as per direction of the Engineer -In - Charge.
Without Fly Ash (Min cement level as per latest IS
shall be maintained) For all R.C.C. memebers at All
Floor Level.
13 Extra for additional height of propping and centering 12.00 Sqm 407.75
where the height of propping and centering exceeds
.O M between supporting floor to ceiling including
temporary brick or stone pillars for supporting as
required. (i)Height more than 4.0 M.and upto 5.0 M
14 Extra for additional height of propping and centering 12.00 Sqm 714.85
where the height of propping and centering exceeds
.O M between supporting floor to ceiling including
temporary brick or stone pillars for supporting as
required. (ii) Height more than 5.0 M.and upto 6.0 M.
15 Providing TMT Bar FE 550D reinforcement for R.C.C. 983855.60 Kg 99.19
work including bending, binding and placing in
position complete for all floors.
16 Providing cement vata (10cm. x 10 cm. size) quarter 2196.00 Rmt 24.28
round in cement mortar 1:1 including neat cement
finishing, watering etc. Complete For All Floor as
directed by Architect or Engineer-in-charge
17 Brick work using common burnt clay conventional 154.00 Cum 4214.09
building bricks having crushing strength not less than
35 Kg/Sqm. in Foundation and Plinth in cement
mortar 1:6 ( 1 cement : 6 fine sand ) including curing
etc. Complete For All Floor as directed by Architect or
Engineer-in-charge
18 Brick work using common burnt clay conventional 3197.00 Cum 4671.28
building bricks having crushing strength not less than
35 Kg/sqcm. in Super structure in cement mortar 1:6 (
1 cement : 6 fine sand ) including curing etc. Complete
For All Floor as directed by Architect or Engineer-in-
Item Rate In
Description of Item Quantity Unit Amount
No figures
19 Half brick masonary in common burnt clay 5653.00 Sqm 707.85
conventional building bricks having crushing strength
not less than 35 Kg/Sq.cm. in C.M. 1:4 ( 1 cement :
coarse sand ) including curing etc. Complete For All
Floor as directed by Architect or Engineer-in-charge
20 Providing 10 mm thick Mala cement plaster with 1x1 16929.56 Sqm 259.61
cm grooves in single coat on brick/concrete
wall/ceiling for interior plastering finished even and
smooth including scaffolding, curing etc. complete. In
Cement mortar 1:3(1 cement : 3 fine sand) Complete
For All Floor as directed by Architect or Engineer-in-
21 Providing 20 mm thick double coat Mala cement 42660.00 Sqm 398.33
plaster with 1x1 cm grooves on interior
brick/concrete work for plastering comprising of base
coat of 12 mm thick cement plaster in Cement mortar
1 : 4 ( 1 cement : 4 coarse sand ) in rough finishing and
8 mm thick top coat of cement mortar 1 : 2 ( 1 cement :
2 coarse sand ) finished with trovel including
scaffolding curing and 1 cm x 1 cm grooves at junction
of structural members etc. Complete For All Floor as
directed by Architect or Engineer-in-charge
22 Providing 20mm thick cement plaster in single coat on 6159.00 Sqm 258.86
single or half brick walls for Exterior plastering upto
All floor level and finished even and smooth in (ii)
Cement mortar 1:4 (1- cement :4-sand) including
scaffolding curing As per Engineer-in charge
23 Providing and laying synthetic plaster of average 2 6159.00 Sqm 687.41
mm thickness on a base of smooth mala plaster having
final coat incorporating fine filaments made up of
polymers and aggregating natural stone powder as
tvaried drection,colour and shade Complete For All
Floor as directed by Architect or Engineer-in-charge
24 Finishing wall with 100% acrylic emulsion 4277.00 Sqm 136.78
wetherproof water repellant paint on wall surface to
give an required shape even shade after thoroughly
brushing the surface to remove all dirt, and remains of
loose powdered materials.etc Complete For All Floor
as directed by Architect or Engineer-in-charge
25 Wall painting (three coats+primer) with plastic 42440.00 Sqm 159.19
emulsion paint of approved brand and manufacture on
new wall surface to give an even shade including two
coats of putty & two coats of primer of approved
brand including thoroughly brushing the surface free
from mortar dropping and other foreign matter and
sand papered smooth Complete For All Floor as
directed by Architect or Engineer-in-charge
Item Rate In
Description of Item Quantity Unit Amount
No figures
26 Painting (three coats+primer) with plastic emulsion 16924.00 Sqm 129.46
paint of approved brand and manufacture on Celing
and sloping surface to give an even shade including
two coats of putty & two coats of primer of approved
brand including thoroughly brushing the surface free
from mortar dropping and other foreign matter and
sand papered smooth Complete For All Floor as
directed by Architect or Engineer-in-charge
27 Providing and laying 600 mm x 600 mm Matt Finished 4856.30 Sqm 2302.90
Full Body Vitrified Tile 7-10 mm Thick in flooring laid
on 20 mm-60mm thick cement mortar 1:6 (1 cement :
6 coarse sand) on new surface and jointed with
coloured cement slurry including finished with flush
pointing & cleaning the surfaceetc (including cost of
10% dark colour tiles for patten of same material)
complete for all floors as directed by Architect or
Engineer in charge.
28 Providing and laying 600 mm x 600 mm Matt Finished 225.00 Sqm 2410.16
Full Body Vitrified Tile 7-10 mm in Skirting laid on
mm thick Adhesive with matching pigments including
cleaning etc. (including cost of 10% dark colour tiles
for patten of same material) Surface already plastered;
no additional plaster included for tile fixing complete
for all floors as directed by Architect or Engineer in
29 Providing and laying 600 mm x 600 mm Full Body 4258.00 Sqm 2552.88
Polished Vitrified Tile 7-10 mm in flooring over
mm-60mm average base of cement morter 1 : 6 (
cement : 6 Coarse sand) on new surface, jointed with
colout cement slurry including finishing with flush
pointing and cleaning the surface etc complete for all
floors as directed by Architect or Engineer in charge.
30 Providing and laying 600 mm x 600 mm Full Body 471.00 Sqm 2192.71
Polished Vitrified Tile 7-10 mm in Skirting laid on
mm thick Adhesive with matching pigments including
cleaning etc. (including cost of 10% dark colour tiles
for patten of same material) Surface already plastered;
no additional plaster included for tile fixing complete
for all floors as directed by Architect or Engineer in
31 Providing and laying 600x600mm Machine Cut Blue 207.00 Sqm 1019.39
Kota stone slab flooring over 20 mm-60mm (Average)
thick base of cement mortar 1:6 (1-cement : 6-coarse
sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand)
laid over and jointed with grey cement slurry mixed
with pigment to match the shade of slab including
rubbing and polishing etc. complete. (A) 25mm thick
All Floor as directed by Architect or Engineer-in-
Item Rate In
Description of Item Quantity Unit Amount
No figures
32 Providing and laying polished kota stone slab 25mm 28.00 Sqm 1701.55
thick in risers of steps,skirting Dedo and pillars laid on
10mm thick Adhesive and jointed with gray cement
slury mixed with pigment to match the shade of slab
including rubbing and polishing etc. Surface already
plastered; no additional plaster included for tile fixing
All Floor as directed by Architect or Engineer-in-
33 Providing and laying 600 mm x 600 mm Matt Finished 595.00 Sqm 2277.95
Anti skid Full Body Vitrified Tile 7-10 mm in flooring
over 20 mm-60mm average base of cement morter 1 :
6 ( 1 cement : 6 Coarse sand) on new surface, jointed
with colout cement slurry including finishing with
flush pointing and cleaning the surface etc complete
for all floors as directed by Architect or Engineer in
34 Providing and laying 300 mm x 300 mm Anti skid 861.00 Sqm 2540.35
Colour Ceramic Tile 7-10 mm in flooring over 20 mm-
60mm average base of cement morter 1 : 6 ( 1 cement
: 6 Coarse sand) on new surface, jointed with colout
cement slurry including finishing with flush pointing
and cleaning the surface etc complete for all floors as
directed by Architect or Engineer in chage.
35 Providing and laying 300mm x 450 mm & 8mm thick 5394.00 Sqm 2502.07
premium digital printed glazed tiles of shade and
design in skirting and dado on 7- 10 cm thick Adhesive
and jointed with white cement slurry with necessary
pigment to match the shade including 3mm spacer as
per approved pattern and aproved colour and size and
Surface already plastered; no additional plaster
included for tile fixing As per Architect or Engineer in
charge for all floors.
36 Providing and laying machine cut free edge machine 629.00 Sqm 2310.27
polished granite stone 16mm - 18mm thick finished
treads and risers in length with 1cm projecting nozing
rounded moulding in ttread laid over 20 mm (av.)
thick of CM 1:6 on treads and 10mm thick CM 1:3 on
risers jointed with grey or colour cement slurry
including rubbing and polishing incl. making Three
No.s of grooves of size 3mm X 3mm along the length of
treads etc. All Floor as directed by Architect or
Engineer-in-charge
Item Rate In
Description of Item Quantity Unit Amount
No figures
37 Providing and laying 16mm - 18mm thick polished 2343.30 Sqm 3224.53
Black or colour Granite stone slab machine cut in
single piece with all exposed edges polished,
chamfered and proected 6mm from finished wall
thickness in sill and jambs laid on 10 mm thick
Adhesive laid over and jointed withgrey cement slurry
including rubbing and polishing etc. complete. also
Fixing: Rear face of granite shall be standed using
clean sand sieve no. 10 passed 2mm fixed with araldite
and dried for at list 36 hours. All Floor as directed by
Architect or Engineer-in-charge
38 Providing and laying 25 mm thick double polished 1867.00 Sqm 1272.80
Kota stone Shelves in single piece including fixinng in
position in cement mortar 1:3 (1 cement : 3 coarse
sand) and joined with grey cement slurrly including
moulding machine cut open edge as dircted by
Engineer in charge etc complete All Floor as directed
by Architect or Engineer-in-charge
39 Providing and laying polished Kota stone slab flooring 679.00 Sqm 1131.24
over 20mm (Average) thick base of cement mortar 1:6
(1-cement : 6-coarse sand) or L.M. 1.1.5 laid over and
jointed with grey cement slurry including rubbing and
polishing etc. complete. (B) 30 mm thick
40 Providing and laying Cement concrete 1:2:4 ( 1 cement 193.70 Cum 4087.13
: 2 coarse sand : 4 graded stone aggregates 20 mm.
nominal size) and curing complete excluding cost of
from work on terrace.
41 Providing and laying broken china mosaic flooring for 1929.80 Sqm 779.70
terrace using 12 mm to 20 mm broken pieces of glazed
tiles to be laid over cement mortar 1:3 to plain or
slope and to be tempered to bring mortar creme out
upto surface using white cement including rounding
off junctions and extending them upto 15 cm along the
wall,clearing with water and oxalic acid etc. as
42 Providing & filling 4 mm wide Epoxy Grouting in 27882.00 Rmt 93.93
Flooring & Wall including all cost of laboure and
material Dedo Etc. All Floor as directed by Architect or
Engineer-in-charge
43 Providing and fixing ACP cladding on side wall of 8.00 Sqm 7542.68
entrance door with floor spring and pivoted shutter
made from T.W. 5 cm × 15 cm styles and 6 Nos. 5 cm ×
5 cm T.W. rails, covered with 6 mm thick water proof
plywood and finished on both sides with 1 mm thick
laminate. Colour, shade, pattern and design of
laminate as approved by the Architect. The door shall
be provided with pivot arrangement and 60 cm long
stainless steel handles on both shutters, complete as
per approved details and direction of the Engineer-in-
Charge. For Entrance
Item Rate In
Description of Item Quantity Unit Amount
No figures
44 Providing and fixing 38 mm thick flush double door 31.00 Sqm 6712.66
shutter, solid core Confirming to IS:2202 & ISI
approved manufacture with Anodized Aluminium
section (door section no 19552-weight not less than
1.1 kg/mt ) frame size 63.5mm x 38mm inserted Non
teak wood frame inside the aluminium section for
durable grip of hinges(6 no each shutter) & Double
shutter with required teakwood batten having 1mm
thick lamination o n both side, Durable Grip shall be
providing with both side 15cm long stainless steel
handle and necessary Locking system of , ,fixtures &
fastenings etc. All Floor as directed by Architect or
Engineer-in-charge
45 Providing and fixing 38 mm thick flush Single door 264.10 Sqm 6167.26
shutter, solid core Confirming to IS:2202 & ISI
approved manufacture with Anodized Aluminium
section ( door section no 19552-weight not less than
1.1 kg/mt ) frame size 63.5mm x 38mm inserted Non
teak wood frame inside the aluminium section for
durable grip of hinges(3 no each shutter) & Single
shutter with required teakwood batten having 1mm
thick lamination on both side, including cost of
Hydraulic Door Closer , Durable Grip shall be
providing with both side 15cm long stainless steel
handle and necessary Locking system of , ,fixtures &
fastenings etc.All Floor as directed by Architect or
Engineer-in-charge
46 Providing & fixing Single shutter Door of WPC (Wood 763.00 Sqm 11235.04
Polymer Composite) Frame 100 mm x 63 mm Density
650 Kgm3 wooden inserted and 24/25 mm thick
Wood Polymer Composite ( WPC ) Flush Door Having
Density of 650 kgm3 with decorative laminate of
(marino, greenlam, royale touche, century, signature)
with PVC Edge beading surrounding shutter &
including S S Aldrop 250mm, both side 15cm long
stainless steel handle and necessary Locking system of
, ,fixtures & fastenings etc. directed by engineer in
47 Providing and fixing three track sliding window 262.40 Sqm 3331.99
standard extruded color anodized aluminum section
equivalent to jindal series c (20mm) section numbers:
frame bottom track 21651, frame top & sides
shutter top rail 20530, bottom rail 20529, side rails
20544, interlock rails 20531. including 5mm thick
transparent tinted float glass, rubber gasket, air lock
strip, and finishing joints with transparent silicon
sealant, complete with aluminium powder coated
fittings and fixtures, All Floor as directed by Architect
or Engineer-in-charge
Item Rate In
Description of Item Quantity Unit Amount
No figures
48 Providing and fixing three track sliding window (2 604.00 Sqm 4704.68
shutter + 1 mosquito net shutter): standard extruded
color anodized aluminum section equivalent to jindal
series c (20mm) section numbers: frame bottom track
21651, frame top & sides 21650, shutter top rail
20530, bottom rail 20529, side rails 20544, interlock
rails 20531. with 5mm thick transparent tinted float
glass, with rubber gasket, air lock strip and finishing
joints with transparent silicon sealant, with aluminium
powder coated fittings and fixtures, All Floor as
directed by Architect or Engineer-in-charge
49 Providing and fixing Ventilation with fixed glass at top, 247.00 Sqm 2284.32
having standared extruded colour anodized
alluminium frame using section of size 63mm x
38.10mm x 1.2mm @ Wt. 0.643 Kg/mt with 5 mm
thick Bajari figure adjustable glass louvers with dual
control two right and two left handle of standard make
as details including 5 mm thick transparent tinted
float glass at top etc All Floor as directed by Architect
or Engineer-in-charge
50 Providing and fixing glazed aluminium window 196.00 Sqm 4760.33
standard extruded colour anodised aluminium
sections equivalent to Jindal Series ‘A’, using frame
section No. 20630 and shutter section No.
including single glazing clip No. 19359, complete with
5 mm thick transparent tinted float glass, fixed with
EPDM rubber gasket, air lock strip and finishing the
joints with approved quality silicone sealantAll Floor
as directed by Architect or Engineer-in-charge
51 Providing & fixing M.S. grills of required pattern to 19596.00 Kg 106.23
wooden frames of windows etc. with M.S. flats at
required spacing & frame around, square or round
bars with round headed bolts & nuts or by
screws(A)Plain grill.Complete. All Floor as directed by
Architect or Engineer-in-charge
52 Painting three coats (one coat of priming coat + two 1307.00 Sqm 128.62
coats of enamel paint) on new steel and other metal
surface with enamel paint, brushing interior to give an
even shade including cleaning the surface of all dirt,
dust and other foreign matter.All Floor as directed by
Architect or Engineer-in-charge
53 Providing and Fixing S.S Hand Rail made S.S 316 of 240.00 Rmt 1621.35
50 mm inside dia 16 guage round pipe supported with
8 mm thick S.S 316 base flange on wall including end
S.S ball 75mm dia, anchor fasteners, nuts, accessories
as per detailed drawing etc. All Floor as directed by
Architect or Engineer-in-charge
Item Rate In
Description of Item Quantity Unit Amount
No figures
54 Providing and Fixing S.S. Railing for staircase made 748.00 Rmt 2946.27
from S.S 316 Grade 1.8 mm wall thickness matt finish,
50 mm Top hand rail, 38 mm Vertical Balustrade fixing
at 1.2 mt C/C with anchor fastner 75 mm dia 8 mm
thick flange and shoe cap, with 3 No of 16 mm
Horizontal pipe fotting with L and Key , modular knob
system. Balustrade top modular "T" fixing support to
50 mm hand rail and turning fixed with modular bend.
including accessories All Floor as directed by Architect
or Engineer-in-charge
55 Providing and fixing white/colour wash down Water 77.00 No 7003.85
closet (European type W.C. Pan) (with seat cover incl.
jet spray) with integral 'p' or 'S' trap including jointing
the trap with PVC/CI soil pipe in C.M. 1:1 including
seat cover and PVC combi flush, dual flush low level
tank 10.0 litres capacity or equivalent brand with all
accessories etc. complete. The BRAND should be as per
given specification or Equivalent or as per directed
engineer in-charge For All Floor.
56 Providing and fixing Orissa Pan Cello 500 x 400 mm a 30.00 No 5552.98
with 'P' or 'S' trap jointed with C.I. pipes in C.M. 1:1
complete for all Floor with all accessories etc.
complete. The BRAND should be as per given
specification or Equivalent or as per directed engineer
in-charge For All Floor.
57 Providing and fixing flat back Wash basin with half 206.00 No 5064.14
pedestal height 405 mm equivalent wall mounted
x 345 x 155 mm size snow white with C.I. or M.S.
bracket including cutting holes and making good the
same including fixing Auxiliaries Waste coupling full
thread, C.P. brass extension nipple 62 mm long, S.S.
flange water super connection pipe 60cm. long and full
thread waste coupling etc. complete.The BRAND
should be as per given specification or Equivalent or
as per directed by engineer in-charge For All Floor.
58 Providing and fixing Flush cock consisting of exposed 107.00 No 2781.84
part (lever, cartridge sleeve, flange) and concealed
part including all accassary and fitting charges etc.
complete.The BRAND should be as per given
specification or Equivalent for All Floor as directed by
Architect or Engineer-in-charge
59 Providing laying and jointing Cowl vent in true line 23.00 No 139.38
and level 110 dia. U.P.V.C. (Type 'B') conforming to IS
13592 of the make as approved by Engineer In Charge
for gutter line jointed with adhesive solvent cement
including cost of all material.
60 Providing laying and jointing Cowl vent in true line 13.00 No 185.84
and level 160 dia. U.P.V.C. (Type 'B') conforming to IS
13592 of the make as approved by Engineer In Charge
for gutter line jointed with adhesive solvent cement
including cost of all material.
Item Rate In
Description of Item Quantity Unit Amount
No figures
61 Providing and fixing Hand Shower (Health Faucet) 126.00 No 1771.34
with 8mm Dia 1.2 Meter Long Flexible Tube and Wall
Hook with including all accassary and fitting charges
etc. complete.The BRAND should be All Floor as
directed by Architect or Engineer-in-charge
62 Providing and fixing Bottle Trap (with Internal 216.00 No 1736.49
Partition) 32mm Size with 250mm Long Wall
Connection Pipes & Wall Flangewith including all
accassary and fitting charges etc. complete.The BRAND
should be as per given specification or Equivalent or
All Floor as directed by Architect or Engineer-in-
63 Providing and fixing Pillar cock with 15 mm dia with 449.00 No 1835.17
C.P. brass extension nipple 62 mm long etc.
complete.The BRAND should be as per given
specification or Equivalent or All Floor as directed by
Architect or Engineer-in-charge
64 Providing and fixing Angle stop cock with 15 mm dia 449.00 No 1364.81
with C.P. brass extension nipple 62 mm long etc.
complete.The BRAND should be as per given
specification or Equivalent All Floor as directed by
Architect or Engineer-in-charge
65 Providing and fixing Bib cock long nose with wall 237.00 No 2985.06
flange and aerator on wall with all Laboure, fittings
and accassary charges etc. completed,The BRAND
should be as per given specification or Equivalent All
Floor as directed by Architect or Engineer-in-charge
66 Providing and fixing 5 mm thick mirror of approved 235.00 No 993.54
quality and make size 600 x 450 mm with moulding
edge by using 4.0 mm thick hard board and fixing on
wall with C. P.brass studs etc. complete. The BRAND
should be as per given specification or Equivalent All
Floor as directed by Architect or Engineer-in-charge
67 Providing and fixing Polycarbonate Convex Mirror 32 2.00 No 2541.36
Inch of approved quality with top cover fixing on wall
with breckets; Made from lightweight
shatterproof/unbreakable, scratch resistant, strong PC
plastic etc. complete. For all floor the BRAND should
be as per given specification or Equivalent or as per
directed engineer in-charge
68 Providing and fixing Towel Ring Round with Round 235.00 No 1074.44
including necessary S.S. screw and labour etc.
complete. The BRAND should be as per given
specification or Equivalent All Floor as directed by
Architect or Engineer-in-charge
69 Providing and fixing Soap Holder including necessary 238.00 No 772.45
S.S. screw with labour etc. complete.The BRAND
should be as per given specification or Equivalent All
Floor as directed by Architect or Engineer-in-charge
Item Rate In
Description of Item Quantity Unit Amount
No figures
70 Providing and fixing toilet paper holder with 238.00 No 1451.88
necessary S.S.screw and labour etc. complete. The
BRAND should be as per given specification or
Equivalent All Floor as directed by Architect or
Engineer-in-charge
71 Providing and fixing drawer type kitchen basket 14.00 Sqmt 22969.60
cupboard using Plywood of 16 to 18 mm thick for
frame and Shutter , With 0.8 mm thick decorative
lamination sheet on Front Side & Inside 0.8mm thick
plain lamination sheet . S.S. telescope channel of
required size, or S.S. fixtures & fastening, handle as
approved quality including using necessary screws,
fevicol, pvc batten including fixing S.S. basket of 19" x
20" (1) Plain multi purpose 100 mm-2 no (2) Cup
soucesser 100 mm-1 No (3) Plate 100 mm -1 No (4)
Thali 200 mm -1 No (5) Vegetable plain 200 mm -1 No
including fixing S.S. telescope channel as per approved
quality and given detail drawing etc. complete.
72 Providing and fixing gun metal check or non return full 40.00 No 420.63
way Handle valve. Zoloto or equivalent make ( C )
mm dia.The BRAND should be as per given
specification or Equivalent or as per directed engineer
73 Providing and fixing gun metal check or non return full 40.00 No 663.43
way handle valve. Zoloto or equivalent make ( E )
mm dia.The BRAND should be as per given
specification or Equivalent or as per directed engineer
74 Providing, fixing, testing & commissoning of GI flanged 20.00 No 1916.48
end lever operated butterfly valve confirming to IS of
Audco or equivalent with necessary specials, unions,
nipple, GI bolt nut, EPDM rubber washers as per
drawing & specifications etc. complete. 50 mm dia.The
BRAND should be as per given specification or
Equivalent or as per directed engineer in-charge
75 Providing, fixing, testing & commissoning of GI flanged 16.00 No 2735.38
end lever operated butterfly valve confirming to IS of
Audco or equivalent with necessary specials, unions,
nipple, GI bolt nut, EPDM rubber washers as per
drawing & specifications etc. complete. 100 mm
dia.The BRAND should be as per given specification or
Equivalent or as per directed engineer in-charge
Item Rate In
Description of Item Quantity Unit Amount
No figures
76 Providing and applying Metric Osmotic treatment 3512.00 Sqm 571.49
(Waterproofing, osmotic, cement-based protective
product for concrete, single-component, thixotropic
covering, resistant to positive and negative hydraulic
pressure) of approved make and quality in two coats
with uniform finish and complete coverage, over
prepared surface free from dust, grease, or loose
particles. Surface shall be cleaned thoroughly before
application. The treatment shall be applied with
brushes only as per manufacturer's specifications and
allowed to dry between coats. as per directed engineer
in-charge. For All Floor
77 Providing and applying black japan treatment of 274.00 Sqm 73.47
approved make and quality in two coats with uniform
finish and complete coverage, over prepared surface
free from dust, grease, or loose particles. Surface shall
be cleaned thoroughly before application. The
treatment shall be applied with brushes only as per
manufacturer's specifications and allowed to dry
between coats. as per directed engineer in-charge. For
78 Providing and fixing hollow metal door with frame 150.00 Sqm 4974.16
made from galvanized iron (GI) sheets, ensuring
stability and integrity. The door leaf shall be 30 to
35mm thick, double skin, fabricated from 1.2mm thick
GI sheet with honeycomb infill, and finished with
powder coating in approved shade. The frame shall be
100x50mm single rebate profile made from 1.5mm
thick GI sheet with inbuilt groove, powder coated to
match. Door shall be fitted with stainless steel hinges
(4 nos. per shutter), aluminum handles, and door
magnets to retain the door in closed position. The
door should open up to 170 degrees for ease of access.
All components shall be factory prepped, field
assembled, and installed complete with all necessary
hardware, accessories, and fixings as per
manufacturer’s specifications. as per directed
engineer in-charge. For All Floor
79 Providing laying and jointing in true line and level 80 90.00 Rmt 993.85
mm dia. U.P.V.C. Pipe ( SCH- 80) for cold water
including fittings Pipe shall be fixed on the wall with
the help of clamp at every two metre C/C or shall be
concelled as directed including necessary fittings etc.
including testing of pipe and joints and fixing the same
with adhesive solvent, including cost of all materials as
per directed engineer in-charge
Item Rate In
Description of Item Quantity Unit Amount
No figures
80 Providing laying and jointing in true line and level 65 140.00 Rmt 758.84
mm dia. U.P.V.C. Pipe ( SCH- 80) for cold water
including fittings Pipe shall be fixed on the wall with
the help of clamp at every two metre C/C or shall be
concelled as directed including necessary fittings etc.
including testing of pipe and joints and fixing the same
with adhesive solvent, including cost of all materials
as per directed engineer in-charge
81 Providing laying and jointing in true line and level 460.00 Rmt 195.67
50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water
including fittings . Pipe shall be fixed on the wall with
the help of clamp at every two metre C/C or shall be
concelled as directed including necessary fittings etc.
including testing of pipe and joints and fixing the same
with adhesive solvent, including cost of all materials.
as per directed engineer in-charge
82 Providing laying and jointing in true line and level 610.00 Rmt 148.12
40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water
including fittings Pipe shall be fixed on the wall with
the help of clamp at every two metre C/C or shall be
concelled as directed including necessary fittings etc.
including testing of pipe and joints and fixing the same
with adhesive solvent, including cost of all materials.
as per directed engineer in-charge
83 Providing laying and jointing in true line and level 960.00 Rmt 91.84
25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water
including fittings Pipe shall be fixed on the wall with
the help of clamp at every two metre C/C or shall be
concelled as directed including necessary fittings etc.
including testing of pipe and joints and fixing the same
with adhesive solvent, including cost of all materials.
as per directed engineer in-charge
84 Providing laying and jointing in true line and level 880.00 Rmt 72.65
15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water
including fittings Pipe shall be fixed on the wall with
the help of clamp at every two metre C/C or shall be
concelled as directed including necessary fittings etc.
including testing of pipe and joints and fixing the same
with adhesive solvent, including cost of all materials.
as per directed engineer in-charge
Item Rate In
Description of Item Quantity Unit Amount
No figures
85 Providing laying and jointing in true line and level 110 741.00 Rmt 876.90
dia. U.P.V.C. (Type 'B') with one end plain and other
end socketed with rubber ring , pipe and fittings
conforming to IS 13592 of the make pipe shall be fixed
on the wall with the help of PVC clamp at every two
metre C/C or shall be concelled as directed including
necessary fittings such as shu bends, tee, shoes etc.
including testing of pipe and joints and fixing the same
with PVC Clamp with adhesive solvent cement
including cost of all material. as per directed engineer
86 Providing laying (to level or slopes) and jointing 612.00 Rmt 678.02
reinforced concrete Light duty non-pressure pipes I.S.
class NP2 of the following internal diameter with
collars and butt ends prepared for collar joints
including testing of joints complete.(D) 300mm
87 Supplying and fixing reinforced concrete heavy duty 100.00 Rmt 1462.01
non pressure pipes with collars for culverts including
setting and joining the pipes in C.M. 1:2 watering and
laying (To level of slops of I.S. 458 / 1971 Class NP3
casted by vertically vibrated technology of following
internal diameter. (ii) 450 mm dia
88 Providing laying and jointing in true line and level 160 390.00 Rmt 834.38
dia. U.P.V.C. (Type 'B') with one end plain and other
end socketed with rubber ring , pipe and fittings
conforming to IS 13592 of the make. pipe shall be fixed
on the wall with the help of PVC clamp at every two
metre C/C or shall be concelled as directed including
necessary fittings such as shu bends, tee, shoes etc.
including testing of pipe and joints and fixing the same
with PVC Clamp with adhesive solvent cement
including cost of all material. as per directed engineer
89 Providing and fixing to wall ceiling and floors 10.0 Kg. 300.00 Rmt 339.05
F/Cm2 working pressure I.S.I. mark P.V.C. pipe of
mm dia low density complete with special flange
compression type fitting such as shu bends, tee, shoes
and wall clamps etc. including making good the wall
ceiling and floor.
90 Supplying and Fixing Z patti type G.I.Brackets for 347.00 Rmt 297.14
SWR/RWR/Water supply Plumbing (down take) pipe
with GI Clamp and Nacessary Fastenrs .
91 Providing and fixing S.S. Cup Type Nahni Trap of 320.00 No 1033.74
Standard quality or it's equivalent including cutting
hole and self clean design itc completed as directed. as
per directed engineer in-charge For All Floor
Item Rate In
Description of Item Quantity Unit Amount
No figures
92 Providing & Fixing Counter Wash Basin into 13.00 Sqm 14180.50
platform of 600 mm wide using Top 18 mm thick
granite of approved shade and sample and bottom
mm thick single side Polished kota stone with 25 mm
thick screed of cement mortar 1:3 With granite Facia
Patti . The stone shall be fixed by chassing in to the
wall surface and supported vertically with 18mm thick
granitestone support including Wash Basin 550 x
x 180 mm waste brass coupling, stainless steel
extension nipple, flexible PVC outlay pipe, Casted
Swinging Spout etc complete as suggested by
Architect/Engineer-in-charge. The BRAND should be
as per given specification or Equivalent or as per
directed engineer in-charge
93 Providing and fixing square mouth trap P or S type of 36.00 No 1246.92
150 mm x 100 mm size SW gully trap with C. I. cover
with frame of 300 mm x 300 mm size (inside) with
standard weight.
94 Providing and laying in trenches 6 Kg. F/Cm2 working 80.00 Rmt 959.10
pressure I.S.I. mark PVC SWR pipe of 160 mm dia low
density pipe including fitting etc complete in ground.
95 Constructig brick masonary chamber of 500 mm x 700 32.00 No 3965.46
mm inside dimension and depth upto 0.45 m for under
ground CI inspection chamber and bends with bricks
having crushing strength not less than 35 Kg/Sqm. in
CM. 1:5 precast fibre reinforced concrete frame &
cover of square frame of approx 800x800x150mm &
round cover 75mm thick, RCC top slab CC 1:2:4 (
cement : 2 coarse sand : 4 graded stone aggregate
mm nominal size ) foundation concrete 1:5:10 inside
plaster 15 mm thick with cement mortar 1:3 finished
smooth with a floating coat of neat cement on walls
and bed concrete etc. complete.
96 Extra over for every additional depth of 0.10m or part 20.00 No 264.86
thereof beyond 0.45 m depth for brick masonry
chamber. (II) For 500 mm x 700 mm
97 Constructing brick masonry chamber for underground 21.00 No 7180.44
C.I. Inspection chamber and bends with briocks having
croshing strength not less than 35Kg. Cm2 in C.M. 1:5
C.I. cover with frame (Light duty) 455mm x 610mm
intenal dimensions, total weight of cover with frame to
be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of
frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-
cement :2- coarse sand :4-graded stone aggregate
20mm size) foundation concrete 1:5:10 inside plaster
15mm thick with cement mortar 1:3 finished smooth
with a floating coat of neat cement on walls and bed
concrete etc. complete.(iii) Inside dimensions 600mm
x 850 mm and 450mm deep for pipe lines with three
or more inlets.
Item Rate In
Description of Item Quantity Unit Amount
No figures
98 Extra over items 98 for every additional depth of 0.1M. 16.00 No 325.59
Of part thereof beyond 450mm depth for Brick
masonry chamber.(iii) for 600mm x 850mm size.
99 Providing erecting and fixing double coated ISI water 80000.00 Litre 3.95
tank of required capacity each with all necessary
fittings and connection etc. complete on terrace
100 Providing and fixing 50 mm dia copper metal ball cock 32.00 No 189.84
of approved quality as directed.
101 Providing, filling and laying Cinder in sunken area 150.00 Cum 458.04
including ramming, watering, consolidating for all
floors etc complete as directed by Engineer in charge.
as per directed engineer in-charge For All Floor
102 Providing and laying Cement concrete 1:2:4 ( 1 cement 112.00 Cum 3922.66
: 2 coarse sand : 4 graded stone aggregates 20 mm.
nominal size) and curing complete excluding cost of
from work Toilet sunk. For All Floor as per directed
engineer in-charge For All Floor
103 Applying Water proofing treatment to sunk portion by 2914.00 Sqm 98.78
applying two coats of Acrylic Polymer base water
guard chemical of approved by Engineer in charge
applied with brush after cleaning of dirt, dust and
other foreign material. as per directed engineer in-
charge For All Floor
104 Providing and fixing 25 mm thick, 50 mm wide 40.00 Rmt 3112.52
Staineless steel letters of any size (Minimum 300 mm)
on 3 mm thick exterior composite panel of any size
with all material, hardware, acessories & fittings etc
completed.
105 Design, supply & installation of Name/Number Plate 13.00 Sqm 9619.54
including lettering made of polyvinayl of approved
color on 1 mm thick stainless steel (S.S 316 ) sheet as
approved by Architect or Engineer-in-charge. For all
106 Design, supply & installation of Signages including 92.00 Sqm 5850.83
normal lettering with additional raised tactile and
graphical symbols, height 15 mm to 55 mm Brailled
text and Braille locator made of zink sulphide based
glow in the dark rigid sheet with high luminous
property enclosed in a transperent weather proof U/V
stabilised plastic pasted on 3 mm thick clear acrylic
sheet sheet.
107 Providing and Making holes ranging from 50 mm to 296.00 Nos 1509.95
200 mm diameter in RCC walls, slabs, or any other RCC
members using a diamond core cutting machine
(HILTI or equivalent), including disposal of debris and
refilling the remaining portion with non-shrink grout
material mixed with an epoxy bonding agent,
complete in all respects as per the direction of
Engineer-in-Charge. For All Floor
Item Rate In
Description of Item Quantity Unit Amount
No figures
108 Providing and fixing Expansion joint following items 391.00 Sqm 13891.24
(a) expansion joint 100 mm thick expansion joint
board of best quality and approved make including
cutting to required size and shape at all levels .
(b) the expansion joint by 600 polymer or equivalent
confirm to BS 4254-1983 as per required shade and
manufactured specification by making groove of
mm x 12.5 mm lather by cutting or by repairing
groove and removing mortar drop or any other
foreign materials including applying primer and filling
required size (oversize of joint PU foam).
(C) Applying and providing Expansion joint sealing
System on 100 mm vide joint including cleaning of
exansion joint by mechanical means provision of
adhesive and flexible membrane with required bond
length as per menufracturer specification and 4mm
thick alluminium strip covering with one side sloted
and bolted with suitable system, inclusive of all
manpower, machinery and material as per
specification and as directed.
(d)fixing 25 cm Wide & 3mm thick exterior composite
panel on existing expansion joint horizontally &
vertically with all material, hardware, acessories &
fittings etc completed.
all items above a to b carry out as per directed
engineer incharge
109 Design, supply & installation of Entrance SS Name 15.00 Sqmt 23404.23
board including digital lettering color on stainless
steel (S.S 316 ) sheet as approved by Architect or
Engineer-in-charge. For all floor
110 Providing and filling holes/gaps of any lenght/depth 240.00 No 270.07
in reinforced cement concrete (RCC) or in masonary of
dia upto 250 mm using factory-packaged, non-shrink,
free-flowing, high-strength cementitious grout such as
GP2 of approved brand as directed by engineer in
charge For All Floor
111 Providing and Fixing 15 mm thick 300 mm x 300 mm 439.00 Sqm 1210.28
Tactile Warning Tiles (Attention Tiles i.e. Tactile
Warning Surface Indicator {TWSI}) of Johnsan Endura
Tac Button Yellow Plus or equvqlent make in flooring
laid on 20 mm thick cement mortar 1:6 (1 cement :
coarse sand) on new surface and jointed with cement
slurry including finished with flush pointing &
cleaning the surface for all floors as per detailed
drawing etc. complete as directed by Architect or
Engineer in charge. Thse tiles shall be Anti Skid,
Chemical Resistant, Fade Proof, Frost - Heat &
Weather Proof, High Flexural Strength, Highly Durable,
Stain Resistance . All Tactile Warning Tiles meet the
specific size and dimension standards as required by
ISO/FDIS 23599. as per directed engineer in-charge.
For All Floor
Item Rate In
Description of Item Quantity Unit Amount
No figures
112 Providing and fixing Matrix Set Accessories for 3.00 set 18932.45
Handicap/ Differently abled toilets including 1 No. of
Hinge rail Matrix set 76 cm Long & 3 Nos. of Grab
Railsof Matrix set 60 cm Long with necessary
S.S.screws, fixtures & fastenings and labour etc.
complete. The BRAND should be as per given
specification or Equivalent or as per directed engineer
113 Providing and fixing chicken mesh jali with square of 9905.00 Sqm 228.06
25 gauge at junction the masonary and RCC member
including necessary scafolding, labour etc.complete .
as per directed engineer in-charge. For All Floor
114 Providing and laying in position REBAR as specified in 400.00 No 221.90
true line & level including drilling adequate hole,
cleaning the same, grouting with HILTI, HY - 200 rebar
system as per manufacturers specifications strictly in
accordance with structural details having minimum
depth of embedment 125mm, etc as per directed
engineer in-charge. For All Floor (a) 10 to 12 mm dia.
115 Providing throating or plaster drip and moulding to 2419.00 Rmt 43.74
R.C.C. Chhajja. as per directed engineer in-charge. For
116 Providing and fixing 25 mm thick shutters for 868.00 Sqm 3179.95
cupboards etc. including anodised alluminium butt
hinges with necessary screws. (A) Indian teak wood.
(i) Fully Panelled. as per directed engineer in-charge.
For All Floor
117 Providing and fixing composite panel cladding work at 100.00 Sqm 4477.88
front with using 3mm thick exterior composite panel
and alluminium natural anodisizing flat of 38.10 x 25 x
1.10 mm with silicone grade 995 & 989 & G.P.where it
is necessary at pressure tape,baker rod size depend
upon gape between two panel with all material,
hardware, acessories & fittings etc completed.
118 Constructing Pantry Platform of 16- 18 mm thick 10.00 Sqm 3907.69
Polished Black Granite having 0.45m width and 0.60m
height including 0.60m support at every 0.7m c/c with
cementing Materials / adhsives including makeing
necessary grooves in walls all required fitting
accessories etc. with all labour material of approved
quality incl. full moulded round front edge granite
strip of one side polished and jointed with grey
cement slurry including rubbing and polishing etc as
per directed engineer in-charge
Item Rate In
Description of Item Quantity Unit Amount
No figures
119 Constructing drinking/Handwash Platform of 16-18 7.00 sqm 4695.49
mm thick Polished Black Granite having 0.45m width
and 0.60m height including 0.60m support at every
0.7m c/c with cementing Materials / adhsives
including makeing necessary grooves in walls
,including Polyamide braided connection pipe 12mm
dia, 450mm length with all fitting inlet and outlet
connection and all required fitting accessories etc.
with all labour material of approved quality incl. full
moulded round front edge granite strip of one side
polished and jointed with grey cement slurry
including rubbing and polishing etc. complete as per
directed engineer in-charge
120 Providing & Fixing Sandwich type Kitchen Platform 12.00 sqm 6874.34
using Top 16 - 18mm thick granite of approved shade
and sample and bottom 23mm to 25 mm thick single
side kota stone with 25 mm thick screed of cement
mortar 1:3 With granite Facia Patti. and vertical End
granite supports. The stone shall be fixed by chassing
in to the wall surface and supported vertically with
23mm to 25mm thick sandwich kota stone support
including SS Sink of size 610 x 460 mm approved by
engineer incharge with waste brass coupling, stainless
steel extension nipple, flexible PVC outlay pipe, with
swivel spout- wall mount type sink cock etc as per
directed engineer in-charge
121 Providing Plinth Protection to Building including 309.00 sqm 2489.45
excavation in ordinary soil and laying cement concrete
1:3:6 using stone aggregates of 40mm nominal size in
foundation layer 125 mm thick+ 125mm thick sand
layer below pre-cast Rubber Dye inter locking
concrete block 60mm thick with grade of concrete
M300 pneumatic compressed by mechanically pressed
and as per approved design including 75mm Sand
layer for levelling and filling the joint with sand in
proper line and level etc. complete, Including
Providing and fixing pre-cast concrete kerb stone of
grey cement based concrete block 30cm length, 30cm
height and 15cm thick made of M250 grade concrete
as per approved design and including excavation for
fixing in proper line and level, filling the joint with C:M
1:3 (1cement:3 fine sand) etc. complete.
122 Providing and fixing UV stabilized HDPE bird 756.00 sqm 277.75
protection net of 25mm aperture, including perimeter
support using nylon rope / SS wire, hooks, clamps, and
all fixing accessories complete for OTS area as per
direction of Engineer-in-Charge.”
Item Rate In
Description of Item Quantity Unit Amount
No figures
123 Providing and fixing aluminium double mosquito net 196.00 sqm 2176.55
shutter, made from standard extruded colour anodised
aluminium sections equivalent to Jindal Series ‘A’,
using suitable frame section and shutter sections, .
fixed with EPDM rubber gasket, and mosquito mesh
fixed in net shutter . The shutters shall be complete
with necessary fittings, fixtures, handles, locking
arrangement, air lock strip and finishing the joints
with approved quality silicone sealant, complete in all
respects for all floors as directed by Architect or
Engineer-in-Charge.”
124 Providing laying and jointing in true line and level 150.00 Rmt 1127.16
200mm dia. Form core Pipe for drainage including
fittings as approved by Engineer In Charge. Pipe shall
be fixed on existing structure, Wall or ground with
the help of clamp or shall be concelled as directed
including necessary fittings etc. including testing of
pipe and joints and fixing the same with adhesive
solvent, including cost of all materials.
125 Providing and fixing to wall ceiling and floor 10.0 Kg. 220.00 Rmt 339.05
F/Cm2 working pressure poluthene pipes of the
following outside Dia. Low densidy, complete with
special falnge compression type fittings, wall clipsetc.
including making good the wall ceiling and
floor.(G)110 mm
126 Providing and fixing to wall ceiling and floor 10.0 Kg. 420.00 Rmt 696.90
F/Cm2 working pressure poluthene pipes of the
following outside Dia. Low densidy, complete with
special falnge compression type fittings, wall clipsetc.
including making good the wall ceiling and
floor.(G)180 mm
127 Providing junction for rain water juncton chamber of 20.00 No 9564.70
size 0.60x0.60x0.75m with excavation of size
1.96x1.96 m & 0.15m thick c.c.1:2:4 bed concrete and
Top slab For M.200 including brick masonary wall in
CM 1:6 of 0.75m height & 0.23m thick with 15mm
thick cement plaster inside & outside & 1.06x1.06 RCC
(1:2:4) slab of thickness 0.15m with FE550D steel and
0.60mx0.45m cast iron manhole cover with frame
weight not less than 35 kg as per directed by Engineer-
in-charge.
128 Providing and installation Recharge pit of “RAIWOHA” 2.00 No. 126092.44
Make 3 layer RCC Precast Injection well system of size
1.5 meter Dia. X 3.4 Meter Height rein forced concrete
precast three layer module with 6” dia x 12” dia. V
wire screen of 0.75mm x 1.0 mm Slot size in SS
material and 1.0 meter height with MS Top cover and
required Air vent including all necessary excavation
and transportation at site including required filter
media for the recharge system as per site requirement.
Item Rate In
Description of Item Quantity Unit Amount
No figures
129 Drilling of min. 250 mm dia. bore hole in all strata 200.00 Rmt 1270.58
including dualover burden strata by combination
DR/DTH rig including lowering 200 mm dia MS ERW
pipes in bore hole and testing etc.all work as per
directed engineer incharge.
130 Supplying slotted PVC pipes of approved quality at site 200.00 Rmt 639.33
of work confirming to IS. 1239/1974 180mm dia.
131 Providing and fixing C.I. Manhole cover 0.60 M. x 2.00 Nos 958.17
0.45M. size having weight not less than 35Kg.
132 20mm thick sand faced cement plaster on walls upto 2422.00 Sqmt 315.69
height 10 metres above ground level consisting of
12mm thick backing coat of C.M. 1:3 (1-cement : 3-
sand) and 8mm thick finishing coat of C.M. 1:1 (1-
cement : 1-sand) etc. complete.
133 Providing and fixing rolling shutters of approved make 10.00 Sqmt 3554.40
made of 80 mm wide M.S laths inter-locked together
through heir entire length and jointed together at the
ends by end locks mounted on specially designed pipe
shaft with bracket plates,guide channels and
arrangement for inside and outside locking with push-
pull operation including the cost of hood cover and
sprig etc.complete(A) Shutters having width below
134 Drilling pilot borehole of size 250/300 mm at above 250.00 Rmt 573.68
site by mud flush direct rotery rig.
135 Reaming of 250/300 mm dia.Pilot borehole to size 550 250.00 Rmt 349.46
mm dia. Incliding assembling ,lowering housing
,casing strainerpipers with gravel packing and clayball
packing etc.
136 Development of cach water bearingzone coming 1.00 Job 27191.22
across the full depth of tubewell by lowering 100 mm
dia.Droplineand 32 mm dia airline for each water
bearing Zone with suitabale capacity air compressar
up to avilability of sand free discharge.
137 900 CFM /200 PSI capacity air compressar upto the 1.00 Job 27603.30
availability of sand free discharge for upto 250 mtrs
138 Supply of M.S. E.R.W. plain end medium duty pipe 250.00 Rmt 3605.70
confirming to IS 4270/2001 with latest amendments
Of size 250 mm dia (minmum thicknes of 7.1 mm)
139 Screen Slotting of MS ERW balnce pipe with size of slot 252.00 slots 0.24
6.75 cm X 6.35 cm X 3.12 mm for 250 mm dia pipe
140 Supply of miscellenious bore material suitable to 250 1.00 Pair 2037.91
mm dia pipes as following (A) MS Bore clamps made
from M.S. plate with 3 holes on either side with nuts &
bolts of std make of size 900X100X16 mm flat suitable
for 250 mm dia pipe.
Item Rate In
Description of Item Quantity Unit Amount
No figures
141 Supply of miscellenious bore material suitable to 250 1.00 No 1161.62
mm dia pipes as following (B) MS Bore Plug having
100mm height made from M.S. plate with 3 holes at
equal distance on circumferrence for nut-bolts type,
locking arrrangement with nuts-bolts & lock nuts of
std make complete from 5 mm thick M.S. plate
suitable for 250mm dia pipe.
142 Supply of miscellenious bore material suitable to 250 1.00 No 1065.02
mm dia pipes as following (C) MS Bail Plug having
length 0.45 mtr from medium class pipe as per I.S.
suitable for 250 mm dia pipe.
143 Supply of miscellenious bore material suitable to 250 168.00 NO 91.71
mm dia pipes as following (D) Steel bent plate suitable
for ERW pipe for 250mm dia (size:200 X 150X6 mm)
145 Electrologging of Pilot bore hole with carting. 1.00 Job 18180.00
146 Geohydrological ground water investigation including 1.00 No 14428.86
vehicle charges for three phase DTH bore/DR tube
well including water sample testing & chemical
147 Providing, supplying and commissioning ISI mark CI 1.00 No 5401.48
D/F Reflux Valves of following class and diameter
including all taxes, insurance, transportation, freight
charges, octroi, inspection charges, loading, unloading,
conveyance to departmental stores stacking etc.
complete. Reflux valves PN 1 IS 5312 with ISI mark
size: 100 mm
148 Manufacture, supply and delivery of following ISI 200.00 Rmt 152.51
marked HDPE pipes (IS:4984/1985 with latest
amendment) having material Grade PE-80 in
approximate 100 meter coil length or as per GWSSB
requirement with SS 316 nipple at both ends having
11 TPI threads as per specifications, press fitted and
bolted having nominal diameter as under as per
detailed technical specifications. v) DN 63 PN-12.5
149 Constructing providing and fabricating cattle guard 6.00 Sqm 5607.52
using channel section frame of size ISMC series
mm x 50 mm (Weight 9.60 kg/Rmt) and ISMC section
40 mm x 75mm (weight 7.13 kg/Rmt) intermediate
support for welding G.I.pipe at 12 Cm C/C of size
mm in a frame made of Channel section size 100 mm x
50 mm all round including fixing the unit on prepared
chamber of masonary wall using MS hold fast
embeded in masonary wall top as directed by Engineer
in charge and as per drawing and necessary required
arrangement etc complete.
Item Rate In
Description of Item Quantity Unit Amount
No figures
150 Providing and fixing concertina razor blade coil 400.00 Rmt 486.82
fencing with punched tape concertina coil 600 mm dia
45 mt openable length having 24 no rounds per 6 mt
length, upto 3mt height of wall with new angle iron
(50mm x50mm x5mm )requird shaped As per
Directed Engeenier in charge. placed 2.2mt apart and
with 4 horizontal R.B.T. reinforced barbed wire(3 mm)
, stud tied with G.I. staples and G.I. clips to retain
horizontal, including necessary bolts or G.I.barbed
wire tied to angle iron, all complete as per direction of
Engineer-in-charge, with reinforced barbed tape
(R.B.T.)/Spring core (2.5 mm thick) and weight
gm/meter at compound wall.
151 Steel work, welded in built up sections framed work 56831.00 KG 88.38
including cutting, hoisting, fixing in position and
applying a priming coat of read lead paint & two coat
oil paint. (A)In beams and joists, channels angles Tees,
flats, with connecting plates or angle cleats as in main
and cross beams. Hip and jack rafters, purlins
conneted to common rafters and the like.(Gate)
152 Supply, installation, testing & commissioning of 1.00 No 29027.40
Priming tank, HDPE type, 1000 litres, with necessary
piping 100 mm size, G.I pipe for priming the pumps,
pipe of with butterfly valves for isolation, Water
Filling to priming tank by piping min. 50 mm size, with
all complete.
153 Supply, installation, testing & commissioning of 1.00 No 29027.40
Manifold( surge vessel,)for fire hydrant system, min.
300 mm diameter, made from M.S plate, hydro tested
to 15 kg./cm2. with ball valves, header with couplings
for fitting pressure switches, pressure gauges etc.with
necessary isolation valves with all complete.
154 Supply, fabrication & erection of aboveground G.I. 'C'- 10.00 Mtr 519.14
Class, ERW piping, conforming to IS:1239, part-I,
Heavy class up to 150 mm dia. and IS:3589, for size
200 mm dia. & above, thickness. G.I. pipe fitting's as
per IS: 1239, part-II, Heavy class for size 150 mm dia.
& below & IS: 3589, for size 200 mm dia. above,
flanges, nuts bolts & washers, 3 mm thick gasket, pipe
hangers, etc.
Hydrostatic testing for 2 hour's at 150% of the system
pressure, hook-up etc.
Painting for piping, fittings & structural pipe support,
shall be two coat of zinc primer and two coats of fire
red conf. to IS: 5, Shade 536. Complete with all
accessories as per approved drawings, specicification
and direction of the Engineer-in-Charge, with all
complete. 25 mm dia.
Item Rate In
Description of Item Quantity Unit Amount
No figures
155 Supply, fabrication & erection of aboveground G.I. 'C'- 15.00 Mtr 834.26
Class, ERW piping, conforming to IS:1239, part-I,
Heavy class up to 150 mm dia. and IS:3589, for size
200 mm dia. & above, thickness. G.I. pipe fitting's as
per IS: 1239, part-II, Heavy class for size 150 mm dia.
& below & IS: 3589, for size 200 mm dia. above,
flanges, nuts bolts & washers, 3 mm thick gasket, pipe
hangers, etc.
Hydrostatic testing for 2 hour's at 150% of the system
pressure, hook-up etc.
Painting for piping, fittings & structural pipe support,
shall be two coat of zinc primer and two coats of fire
red conf. to IS: 5, Shade 536. Complete with all
accessories as per approved drawings, specicification
and direction of the Engineer-in-Charge, with all
complete. 50 mm dia.
156 Supply, fabrication & erection of aboveground G.I. 'C'- 30.00 Mtr 1530.15
Class, ERW piping, conforming to IS:1239, part-I,
Heavy class up to 150 mm dia. and IS:3589, for size
200 mm dia. & above, thickness. G.I. pipe fitting's as
per IS: 1239, part-II, Heavy class for size 150 mm dia.
& below & IS: 3589, for size 200 mm dia. above,
flanges, nuts bolts & washers, 3 mm thick gasket, pipe
hangers, etc.
Hydrostatic testing for 2 hour's at 150% of the system
pressure, hook-up etc.
Painting for piping, fittings & structural pipe support,
shall be two coat of zinc primer and two coats of fire
red conf. to IS: 5, Shade 536. Complete with all
accessories as per approved drawings, specicification
and direction of the Engineer-in-Charge, with all
complete. 80 mm dia.
157 Supply, fabrication & erection of aboveground G.I. 'C'- 300.00 Mtr 2196.75
Class, ERW piping, conforming to IS:1239, part-I,
Heavy class up to 150 mm dia. and IS:3589, for size
200 mm dia. & above, thickness. G.I. pipe fitting's as
per IS: 1239, part-II, Heavy class for size 150 mm dia.
& below & IS: 3589, for size 200 mm dia. above,
flanges, nuts bolts & washers, 3 mm thick gasket, pipe
hangers, etc.
Hydrostatic testing for 2 hour's at 150% of the system
pressure, hook-up etc.
Painting for piping, fittings & structural pipe support,
shall be two coat of zinc primer and two coats of fire
red conf. to IS: 5, Shade 536. Complete with all
accessories as per approved drawings, specicification
and direction of the Engineer-in-Charge, with all
complete. 100 mm dia.
Item Rate In
Description of Item Quantity Unit Amount
No figures
158 Supply, fabrication & erection of aboveground G.I. 'C'- 60.00 Mtr 3282.50
Class, ERW piping, conforming to IS:1239, part-I,
Heavy class up to 150 mm dia. and IS:3589, for size
200 mm dia. & above, thickness. G.I. pipe fitting's as
per IS: 1239, part-II, Heavy class for size 150 mm dia.
& below & IS: 3589, for size 200 mm dia. above,
flanges, nuts bolts & washers, 3 mm thick gasket, pipe
hangers, etc.
Hydrostatic testing for 2 hour's at 150% of the system
pressure, hook-up etc.
Painting for piping, fittings & structural pipe support,
shall be two coat of zinc primer and two coats of fire
red conf. to IS: 5, Shade 536. Complete with all
accessories as per approved drawings, specicification
and direction of the Engineer-in-Charge, with all
complete. 150 mm dia.
159 Supply, fabrication & erection of aboveground G.I. 'C'- 7.00 Mtr 4451.07
Class, ERW piping, conforming to IS:1239, part-I,
Heavy class up to 150 mm dia. and IS:3589, for size
200 mm dia. & above, thickness. G.I. pipe fitting's as
per IS: 1239, part-II, Heavy class for size 150 mm dia.
& below & IS: 3589, for size 200 mm dia. above,
flanges, nuts bolts & washers, 3 mm thick gasket, pipe
hangers, etc.
Hydrostatic testing for 2 hour's at 150% of the system
pressure, hook-up etc.
Painting for piping, fittings & structural pipe support,
shall be two coat of zinc primer and two coats of fire
red conf. to IS: 5, Shade 536. Complete with all
accessories as per approved drawings, specicification
and direction of the Engineer-in-Charge, with all
complete. 200 mm dia.
160 Supply, installtion, testing & commissioing of 15.00 Mtr 2626.00
Underground GI (ERW) piping conforming to IS:1239,
part-I, Heavy class ('C' class) up to 150 mm dia. and
IS:3589 Heavy class ('C' class), for 200 mm dia. &
above, min. 6.35mm thickness including Heavy class
fittings, anti-corrosive tape of size 150 mm wide x
mm thick, wrapping & coating with 13KV holiday
testing . Rates shall include sand bedding of 75mm dia
all around, backfilling of the excavated including
installation of heavy pipe fitting's, flanges, etc. 10 % of
all the welded joints shall be done radiographically
tested and 50% of the joints radiographed shall be the
"Field Joints". Hydrostatic testing for 2 hours at 150%
of the system pressure, hook-up etc., complete with all
accessories as per approved drawings, specicification
and direction of the Engineer-in-Charge, with all
complete. (Road Crossing) 100 mm dia.
Item Rate In
Description of Item Quantity Unit Amount
No figures
161 Supply, installtion, testing & commissioing of 20.00 Mtr 3960.21
Underground GI (ERW) piping conforming to IS:1239,
part-I, Heavy class ('C' class) up to 150 mm dia. and
IS:3589 Heavy class ('C' class), for 200 mm dia. &
above, min. 6.35mm thickness including Heavy class
fittings, anti-corrosive tape of size 150 mm wide x
mm thick, wrapping & coating with 13KV holiday
testing . Rates shall include sand bedding of 75mm dia
all around, backfilling of the excavated including
installation of heavy pipe fitting's, flanges, etc. 10 % of
all the welded joints shall be done radiographically
tested and 50% of the joints radiographed shall be the
"Field Joints". Hydrostatic testing for 2 hours at 150%
of the system pressure, hook-up etc., complete with all
accessories as per approved drawings, specicification
and direction of the Engineer-in-Charge, with all
complete. (Road Crossing) 150 mm dia.
162 Supply, installation, testing & commissioning of 150 6.00 No 3560.25
mm dia. dial Burdon Type Glycerine Filled pressure
gauge with isolation ball valve arrangements with
necessary isolation valves with all complete.( Range
163 Supply, Installation, Testing & Commissioning of Cast 7.00 No 2614.89
iron body Butterfly valve according to IS: 13095, PN-
1.6, Iron Disc for size 150 mm dia. & below Lever
operated and above 150 mm dia. Gear operated
complete with mating flanges /ANSI class # 150 with
bolts & nuts washers, rubber gaskets 3 mm thick, etc.,
with all complete. 50 mm dia.
164 Supply, Installation, Testing & Commissioning of Cast 3.00 No 3338.05
iron body Butterfly valve according to IS: 13095, PN-
1.6, Iron Disc for size 150 mm dia. & below Lever
operated and above 150 mm dia. Gear operated
complete with mating flanges /ANSI class # 150 with
bolts & nuts washers, rubber gaskets 3 mm thick, etc.,
with all complete. 80 mm dia.
165 Supply, Installation, Testing & Commissioning of Cast 6.00 No 4061.21
iron body Butterfly valve according to IS: 13095, PN-
1.6, Iron Disc for size 150 mm dia. & below Lever
operated and above 150 mm dia. Gear operated
complete with mating flanges /ANSI class # 150 with
bolts & nuts washers, rubber gaskets 3 mm thick, etc.,
with all complete. 100 mm dia.
166 Supply, Installation, Testing & Commissioning of Cast 4.00 No 5841.84
iron body Butterfly valve according to IS: 13095, PN-
1.6, Iron Disc for size 150 mm dia. & below Lever
operated and above 150 mm dia. Gear operated
complete with mating flanges /ANSI class # 150 with
bolts & nuts washers, rubber gaskets 3 mm thick, etc.,
with all complete. 150 mm dia.
Item Rate In
Description of Item Quantity Unit Amount
No figures
167 Supply, installation, testing & commissioning of Cast 2.00 No 2002.83
iron body Dual Plate Wafer Type NRV conf. to IS:
PN-1.6 complete with mating Flanges class # 150 with
bolts & nuts, washers, gaskets 3 mm thick, etc., with all
complete Accessories 50 mm dia.
168 Supply, installation, testing & commissioning of Cast 1.00 No 2892.64
iron body Dual Plate Wafer Type NRV conf. to IS:
PN-1.6 complete with mating Flanges class # 150 with
bolts & nuts, washers, gaskets 3 mm thick, etc., with all
complete Accessories 80 mm dia.
169 Supply, installation, testing & commissioning of Cast 2.00 No 4116.76
iron body Dual Plate Wafer Type NRV conf. to IS:
PN-1.6 complete with mating Flanges class # 150 with
bolts & nuts, washers, gaskets 3 mm thick, etc., with all
complete Accessories 100 mm dia.
170 Supply, installation, testing & commissioning of Cast 1.00 No 7565.91
iron body Dual Plate Wafer Type NRV conf. to IS:
PN-1.6 complete with mating Flanges class # 150 with
bolts & nuts, washers, gaskets 3 mm thick, etc., with all
complete Accessories 150 mm dia.
171 Supply, installation, testing & commissioning of SG 1.00 No 1446.32
iron body SinglePlate Wafer Type NRV conf. to ASTMA
536, PN-1.6 complete with mating Flanges class #
with bolts & nuts, washers, gaskets 3 mm thick, etc.,
with all complete. Accessories 50 mm dia.
172 Supply, installation, testing & commissioning of SG 1.00 No 1890.72
iron body SinglePlate Wafer Type NRV conf. to ASTMA
536, PN-1.6 complete with mating Flanges class #
with bolts & nuts, washers, gaskets 3 mm thick, etc.,
with all complete. Accessories 80 mm dia.
173 Supply, installation, testing & commissioning of SG 1.00 No 2336.13
iron body SinglePlate Wafer Type NRV conf. to ASTMA
536, PN-1.6 complete with mating Flanges class #
with bolts & nuts, washers, gaskets 3 mm thick, etc.,
with all complete. Accessories 100 mm dia.
174 Supply, installation, testing & commissioning of Y 1.00 No 7232.61
Type Strainer complete with mating flanges with bolts
& nuts, washers, gaskets 3 mm thick, etc., with all
complete accessories. 80 mm dia.
175 Supply, installation, testing & commissioning of Y 1.00 No 9457.64
Type Strainer complete with mating flanges with bolts
& nuts, washers, gaskets 3 mm thick, etc., with all
complete accessories. 100 mm dia.
176 Supply, installation, testing & commissioning of Y 2.00 No 15020.72
Type Strainer complete with mating flanges with bolts
& nuts, washers, gaskets 3 mm thick, etc., with all
complete accessories. 150 mm dia.
Item Rate In
Description of Item Quantity Unit Amount
No figures
177 Supply, installing, testing and commissioning of 1.00 No 5451.98
Normax make CI heavy duty ball type foot valve with
flanges, nut bolts, gaskets etc. with necessary complete
accessories. 80 mm dia.
178 Supply, installing, testing and commissioning of 1.00 No 8011.32
Normax make CI heavy duty ball type foot valve with
flanges, nut bolts, gaskets etc. with necessary complete
accessories. 100 mm dia.
179 Supply, installing, testing and commissioning of 1.00 No 16134.75
Normax make CI heavy duty ball type foot valve with
flanges, nut bolts, gaskets etc. with necessary complete
accessories. 150 mm dia.
180 Supply, installation, testing & commissioning of Four 1.00 No 11683.68
way fire brigade Inlet connection with 63 mm dia.
stainless steel (SS304) instantaneous male inlets with
built in non return valve in each inlet with 150 mm
dia. header pipe, suitable rubber cap and GI chain
including nuts, bolts, washers, gasket 3 mm thick, etc.
with all complete.
181 Supply, installation, testing & commissioning of Two 1.00 No 6676.10
way fire brigade Inlet connection with 63 mm dia.
stainless steel (SS304) instantaneous male inlets with
built in non return valve in each inlet with 100 mm
dia. header pipe, suitable rubber cap and GI chain
including nuts, bolts, washers, gasket 3 mm thick, etc.
with all complete.
182 Supply & installation of stainless steel body Orifice 22.00 No 1390.77
Plate of suitable inner bore along with matching flange
- as per specification & requirement as per hydraulic
calculation.
183 Supply, installation, testing & commissioning of 22.00 No 7065.96
Oblique pattern type stainless steel (SS 304) single
headed External Fire Hydrant Valve with 63 mm dia.
female instantaneous outlet conf. to IS: 5290, type - A,
including mating flanges, galvanised nuts, galvanised
bolts/studs, washers & gaskets 3 mm thick with all
184 Supply, installation, testing & commissioning of 63 22.00 No 2281.59
mm dia. stainless steel (SS 304) Universal Branch Pipe
conf. to IS:
185 Supply & installation, testing & commissioing of Fire 22.00 No 9057.68
Fighting Hose - conf. to IS : 636, type B (type- 3), The
fire hose shall be 15 m long with 63 mm dia. stainless
steel (SS 304) couplings conf. to IS: 903, at both the
ends for connection with the hydrant valve and the
branch pipe.
Item Rate In
Description of Item Quantity Unit Amount
No figures
186 Supply, installation, testing & commissioning of 22.00 No 3282.50
fabricated from 3 mm MS sheet, hose box of size-450
mm x 600 mm x 250 mm - painted with Fire Red as per
IS: 5, shade no. 536 front 3 mm thick transparent glass
with lock & key, handle and brass hinges - to
accommodate one number of 15 mtr long hose and
one number of universal branch pipe, including
supporting arrangement with civil work.
187 Supply, Installation, testing & commissioing of 22.00 No 9624.29
Swinging type mild steel hose reel drum with 20 mm
dia. x 30 mtr. rubber hose as per IS: 884. The mounting
stand shall be of mild steel and the hose shall be fitted
with a SS shut-off nozzle & SS ball valve of 25 mm dia.
including supporting arrangement with all complete.
accessories
188 Filling Of Gaps Between pipe and Core Cutting Hole 56.00 No 388.85
With Chemical and Cement
189 Supply, Filling and Fixing of approved make ABC type 35.00 No 2559.34
fire extinguisher - 6 Kg. Capacity as per IS:15683 & IS :
190 Supply, Filling and Fixing of approved make CO2 type 35.00 No 7177.06
fire extinguisher. Capacity 4.5 Kg. (conforming to IS-
191 Supply, Filling and Fixing of approved make ABC 10.00 No 4450.06
Moduler type automatic fire extinguisher. Capacity
Kg. (conforming to IS-15683).
192 Supply, Installation and commissioning of Air Release 4.00 No 1836.18
Valve, 25 mm Dia. connection.
193 Box cutting the road surface to proper slope and 1101.00 Cum. 109.24
camber for making a base for road work including
removing the excavated stuff and depositing on the
road side slope as directed upto All .lead.
194 Construction of granular sub-base 150mm thick layer 302.70 Cum. 1415.01
by providing coarse graded machine crushed B.T.
material satisfying MOST specification of grading I
(B.T. stone aggregate 53 mm to 26.5 mm 35 %, 26.5 to
4.75 mm - 45 % and 2.36 mm below - 20 % )including
spreading in uniform layer with motor grader on
prepared surface, mixing by mix in place method with
rotavator at OMC and compacting with vibratory roller
to achieve the desired density etc. complete.
195 Providing and laying wet mix macadam 0.15m thick 302.70 Cum. 1476.62
layer base course using machine crushed B.T. chips as
per required gradation mixing with required optimum
quantity of water, conveying the mix to site of work,
spreading in to grade and camber with mechanical
paver and consolidation each layer with vibratory
roller including cost of material labour plant and
equipment etc. complete.
Item Rate In
Description of Item Quantity Unit Amount
No figures
196 Providing and laying trimix vaccum dewatering 314.40 Cum. 5693.37
process of Ready Mixed M-250 grade concrete for
reinforced cement concrete work in Road , using
cement content as per approved Design Mix
manufactured in fully automatic batching plant
established on site and transported to site of work in
transit mixer having continuous agitated mixer,
manufactured as per mix design of specified grade for
reinforced cement concrete work including pumping
of R.M.C. from transit mixer to site of laying, excluding
the cost of reinforcement and centering. shuttering,
formwork finishing and admixtures in recommended
proportions as per IS : 9103 to accelerate/ retard
setting of concrete, improve workability without
impairing strength and durability as per direction of
the Engineer -In - Charge. Without Fly Ash (Min
cement level as per latest IS 456 shall be maintained)
including Compaction and finishing of cement
concrete surface by trimix process ,inclusive of labour
charges for the trimix vacuum dewatering process on
cement concrete surface by using vacuum dewatering
pump, surface floater, surface vibrator and
machanical trowel including Channelling & making
grooves and rough finish to surface by providing
197 Providing and fixing pre-cast Rubber Dye / steel Dye 3453.00 Sqm 706.90
inter locking concrete block 60mm thick with grade of
concrete M300 pnumatic compressed / vibrated
mechanically and as per approved design Confirming
to IS 15658 : 2006 including 35 mm Sand layer for
levelling and filling the joint with sand in proper line
and level as per guidlines of IRC : SP 63-2018 etc.
198 Providing and fixing pre-cast concrete kerb stone of 762.00 Rmt 374.92
gray cement based concrete block 30cm length,30cm
height and 15cm thick of M250 grade concret as per
approved design and including excavation for fixing in
proper line and level,filling the joint with C:M 1:3
(1cement:3fine sand) etc complete.
199 Providing and fixing of Ridge flashing for roof panel 2000.00 Sqm 867.39
shall be made out of 0.5 mm thick pre coated GI sheet .
The Precoated sheet shall be of minimum 240 mpa
steel grade confirming to IS 14246:1995 and shall
have zinc coating of minimum 120 gsm as per
IS:277:1992 , 5-7 microns epoxy primer on both side
of the sheet and polyester top coat 15-18 micron. The
PPGI Sheet shall have plastic protective guard film of
minimum 25 microns to avoid scratches during
transportation. The ridge shall be fixed to the steel
members by pop rivet or self drilling/self stitching
fastners @ maximum 450 mm c/c along length of
capping/flashing etc complete .
Item Rate In
Description of Item Quantity Unit Amount
No figures
200 Road marking with hot applied thermoplastic paints 286.00 Sqmt 367.72
with reflectorising glass beads on bitumin surface
providing and laying a hot applied thermoplastic
compound 2.5 mm thick including reflectorising glass
beads @ 250gms per sqm area, thickness of 2.5mm is
excluding of surface applied glass beds as per IRC:35-
2015. The finished surface to be level, uniform and
free from streaks and holes. zebra patta /bump patta
lane/center line/ edge line/cut patta. The white color
marking should provide liminance coefficinet on
cemend road shalll be min 130 mcd/m2/lux and
Asphalt road shall be min 100 mcd/m2/lux during the
service life during the day time. The marking should
meet the performance criteria for night time
reflectivity, wet reflectivity and skid resistance as
mentioned in the section-15 of IRC 35-2015. Warranty
for the Retro reflectivity should be two years.
201 Providing and laying (two level or slopes) and jointing 40.00 Rmt. 519.37
with stiff mixture of Cement Mortar in proportion 1:1,
Salt glazed stone ware pipes of Dia 150 mm Including
Testing of pipe and Joint complete on providing and
laying of lime concrete 1:5:10 (1-Lime putty :5-Fine
samd : 10-Graded brick aggregates 40mm nominal
size) bedding for stoneware pipes of 150mm internal
diameters with necessary formwork and curing
202 Providing and fixing a study table of size 1200 × 610 × 558.00 No. 4391.35
762 mm, with the table top made from 19 mm thick
BWR calibrated plywood, finished with 1 mm thick ISI
laminate on the top surface and 0.8 mm thick laminate
on the bottom surface. The table shall include a
vertical and horizontal structural framework
fabricated from 50 × 25 × 1.2 mm thick ERW
rectangular CRC tubes, along with additional
structural supports made from 19 × 19 × 1.2 mm thick
ERW CRC tubes. A footrest shall be provided using
mm diameter × 1.2 mm thick ERW round tube. The
table shall be equipped with good quality adjustable
studs at the bottom. All steel components shall be
powder coated with standard quality powder coating
after undergoing a 10-tank anti-rust treatment
process. The complete work shall be executed as per
the specifications, drawings, and directions of the
Engineer-in-Charge.
Item Rate In
Description of Item Quantity Unit Amount
No figures
203 Supplying and placing a single bed of overall size 2080 558.00 No. 13168.42
× 965 × 838 mm, with a seating height of 387 mm,
comprising a base made of 19 mm thick plywood
finished with 1 mm thick laminate. The bed shall have
a vertical and horizontal structural framework
fabricated from 50 × 25 × 1.2 mm thick ERW
rectangular CRC tubes, with additional structural
members made from 25 × 25 × 1.2 mm thick ERW
square CRC tubes. The headboard shall consist of a
0.50 m high wooden back support made from 19 mm
thick plywood fixed within a CRC steel frame, and the
front portion shall be 0.60 m high with similar wooden
ply panels integrated into the steel frame. A mid panel
of 18 mm thick BWR grade ISI standard plywood shall
be provided and finished with oil paint. The bed shall
be supported on bottom legs made from 38 mm
diameter teak wood sections, finished with French
polishing. All steel components shall be treated with a
10-tank anti-rust process and finished with high-
quality powder coating. The complete work shall be
executed as per the specifications and as directed by
the Engineer-in-Charge.
204 Providing and fixing a bedside locker of overall size 558.00 No. 6787.84
600 × 450 × 450 mm, comprising two drawers and
constructed from flat laminated plywood panels made
of 16 mm thick BWR calibrated plywood conforming
to IS 303, finished with 1 mm thick laminate on all
exposed outer surfaces and 0.8 mm thick laminate on
all inner non-visible surfaces, including 0.7 mm thick
backer laminate on both sides, all bonded using high-
quality PUR adhesive. The unit shall be complete with
two drawers mounted on telescopic channels with
proper locking arrangement. The entire work shall be
executed as per the specifications, drawings, and
directions of the Engineer-in-Charge.
205 Providing and fixing a book storage rack of size 1200 558.00 No. 8711.25
mm (length) × 300 mm (depth) × 900 mm (height),
designed as a ready-to-assemble type, suitable for wall-
mounted, overhanging, or partition-mounted
installation. The unit shall be fabricated from 16 mm
thick BWR calibrated plywood conforming to IS
finished with 1 mm thick high-pressure laminate on
both sides, with all surfaces bonded using high-quality
PUR adhesive. The rack shall be securely fixed to the
wall with suitable fasteners and supporting
arrangements to ensure proper stability and load-
bearing capacity. The complete work shall be executed
as per specifications, drawings, and directions of the
Engineer-in-Charge.
Item Rate In
Description of Item Quantity Unit Amount
No figures
206 Providing and fixing a drawer unit of size 600 × 450 × 558.00 No. 6921.39
600 mm, made from flat laminated plywood panels of
16 mm thick BWR calibrated plywood conforming to
IS 303, finished with 1 mm thick high-pressure
laminate on both sides and bonded with high-quality
PUR adhesive. The unit shall consist of one top drawer
and one bottom shutter-type locker, complete with
heavy-duty drawer channels, suitable drawer handle,
shutter with hinges, and locking arrangement. All
necessary fittings and hardware shall be of approved
quality. The complete work shall be executed as per
specifications and as directed by the Engineer-in-
207 Providing and fixing a wardrobe of size 1800 mm 558.00 No. 19164.75
(height) × 1200 mm (width) × 600 mm (depth), having
4 shutters, designed as a ready-to-assemble type as
per approved drawing and pattern. The wardrobe
shall be fabricated from 16 mm thick BWR calibrated
plywood conforming to IS 303, finished with 1 mm
thick high-pressure laminate on all exposed and
internal surfaces, all bonded using high-quality PUR
adhesive. The shutters shall be framed and panelled
type as per design, with proper edge finishing and
polishing of all exposed edges for a smooth and
durable finish. The unit shall include internal wooden
shelves made from matching plywood of required
thickness, properly supported and fixed within the
structure.
All shutters shall be provided with heavy-duty
SS/approved quality hinges, suitable designer handles,
magnetic catchers, and locking arrangement including
tower bolts and chain lock for secure operation. The
carcass shall be properly stiffened with necessary
vertical and horizontal supports to ensure structural
stability. The complete wardrobe shall be fixed in
position with required hardware and fittings. The
work shall be completed with all accessories, fittings,
208 Providing and fixing soft board panels on workstation 301.32 Sqmt 2144.23
partitions of height 0.45 m in required colour and
shade, comprising 9 mm thick non-woven fabric panel
pasted on 3 mm thick high-impact compact laminate
backing board, fixed in required position. The panel
shall be provided with aluminium frame (minimum
mm × 12 mm section, anodized finish) on all edges,
with proper mitre joints. The board shall be fixed on
Wall / partition panel using approved adhesive and
mirror caps with screws, complete in all Floor respects
as per specification and direction of Engineer-in-
Item Rate In
Description of Item Quantity Unit Amount
No figures
209 roviding and fixing full/low height partition with 215.73 Sqmt 4554.19
overall thickness 80 mm (double skin), fabricated from
anodized aluminium sections comprising vertical
studs (min. 50 × 25 mm) at 600 mm c/c and horizontal
members at top, bottom, and intermediate levels,
including door frame provisions, rigidly fixed to
floor/wall/ceiling with cleats and fasteners. Both faces
shall be finished with 12 mm pre-laminated plywood
panels inserted in section grooves with flush finish,
without visible screws or adhesive, complete with
aluminium beading, corner/joint profiles, gaskets,
buffers, and all necessary accessories, including
cutting, fitting, and installation, as per specifications
and direction of Engineer-in-Charge.
210 Providing Cabin Doors made from 32mm BWR ply 63.00 Sqmt 5646.51
and 1 mm laminate and matching with partitions
having overall size as directed by Architect ,view glass
and hardware like handles, door closer and dead lock
etc as specifed in specification sheet, as specifed in
specification sheet,as per direction of engineer
211 roviding and fixing canteen dining table set of overall 50.00 No. 30199.00
size 2300 × 900 × 730 mm with integrated seating
benches on both sides, suitable for 8 persons (face-to-
face/single face) as per approved drawings. The table
top shall consist of 1.6 mm thick SS 304 grade sheet in
matt finish fixed over 8 mm thick waterproof plywood,
supported on top frame made from 20 × 20 × 3.0 mm
thick SS 202 grade angle section as per detailed top &
frame assembly. The legs and footrest shall be
fabricated from 40 × 40 × 1.2 mm thick SS 202 grade
square tubes, complete with PVC adjustable studs at
bottom, and all SS components shall be properly
welded, ground, and finished in matt finish.
The seating benches shall be rigidly integrated with
the table frame, fabricated from 40 × 40 × 1.2 mm
thick SS 202 square tube structure including leg and
footrest supports, with wooden seating made from
teak wood sections of size approx. 2300 × 350 ×
mm finished with French polishing. The complete
structure shall be fabricated in box section form
ensuring high rigidity and durability, designed for load
capacity of 10–12 persons, including all materials,
fabrication, polishing, finishing, and installation, as per
specification sheet and directions of the Engineer-in-
Item Rate In
Description of Item Quantity Unit Amount
No figures
212 Providing and fixing a study chair of size 1'-7" (L) × 1'- 558.00 No. 5575.20
7½" (W) × 3'-0" (H) as per approved drawings. The
chair shall have an under-structure fabricated from
CRC rectangular pipe of size 1.5" × 0.75" × 1.1 mm
thickness, with additional structural supports made
from 0.75" × 0.75" × 1.1 mm thick CRC square tubes.
The seat and back framework shall be supported with
MS flat strips of size 0.75" × 0.125". The seating shall
be provided with teak wood sections of size 2.75" ×
1.0" thickness, and the backrest shall be made of teak
wood sections of size 2.75" × 0.75" thickness, both
finished with French polishing. Armrests shall be
made from teak wood sections of size 1.75" × 1.5"
thickness, also finished with French polishing. All steel
components shall be treated with a 10-tank anti-rust
process and finished with standard quality powder
coating. The item shall include all materials, labour,
fabrication, finishing, and installation complete, as per
specifications and as directed by the Engineer-in-
213 Providing and fixing a three-seater sofa of size 1800 × 9.00 No 17725.50
750 × 700 mm, having seat made of high-density PU
foam of 60 ± 2 kg/m³ with additional top layer of 40 ±
2 kg/m³ for comfort, upholstered with approved
quality jute fabric with proper stitching and finishing.
The backrest shall be made of PU foam of 40 ± 2 kg/m³
upholstered with matching fabric. The internal frame
and armrests shall be made from seasoned plywood
structure with necessary supports, webbing, and
cushioning for durability and load-bearing capacity.
The sofa shall be complete with proper base support,
edge finishing, and all accessories including fabric
lining, cushioning, and legs as required, finished neatly
and installed in position as per specifications and
direction of the Engineer-in-Charge.
214 Providing and fixing a two-seater sofa of size 1200 × 9.00 No 22977.50
750 × 700 mm, having seat made of high-density PU
foam of 60 ± 2 kg/m³ with additional top layer of 40 ±
2 kg/m³ for enhanced comfort, upholstered with
approved quality jute fabric with proper stitching and
finishing. The backrest shall be made of PU foam of
± 2 kg/m³ upholstered with matching fabric. The
internal frame and armrests shall be made from
seasoned plywood structure with adequate supports,
webbing, and cushioning to ensure strength and
durability. The sofa shall be complete with proper
base support, finishing, and all necessary accessories
including fabric lining, cushioning, and legs, installed
as per specifications and direction of the Engineer-in-
Item Rate In
Description of Item Quantity Unit Amount
No figures
215 Providing Medium back revolving & tilting chair As 4.00 No. 20351.50
per approved sample Back ht is 22" from the seat.
Chair under structure made from 19mmX16G CRC
pipe, Upholstered by 2 inch PU density 60 +/- 2 kg
per / cum. foam and in seat and 1 inch PU foam in
back rest, covered with approved premium fabric
quality. Soft handle as per sample Bottom: 38mm
dia x 1.6 mm thick pipe used in five prone stand with
castors, Single position lock, gas lift operating system
and synchro tilt mechanism made from M.S. sheet [
2.5, 3.15, 4mm thickness], duly powder coated as per
instructions of Engineer in Charge etc. complete.
216 Providing Low back revolving & tilting chair, as per 4.00 No. 12473.50
approved sample by chief architect/project in charge,
hot pressed bend ply in seat and back,
ergonomically designed. Upholstered with PU foam
PU density 60 +/- 2 kg per / cum in seat and back.
covered with approved premium fabric quality. Back
Height is 16" from the seat. Soft PU handle as per
sample Bottom: 38mm dia x1.6mm thick pipe used in
five prone stand with castors, Single position lock, gas
lift operating system and tilt mechanism made from
M.S. sheet[2.5,3.15,4mm thickness], duly powder
coated ,as per instructions of Engineer in Charge etc.
217 Providing Visitor’s group seating chair of Three , Top 10.00 No 13332.00
shell made from perforated MS CRC sheet of 20 SWG
duly powder coated . Bottom: Made from 20X40mm
M.S. CRC tubes, as per sample duly powder coated to
40 to 50 micron, as specifed in specification sheet, as
per instructions of Engineer in Charge etc. complete.
218 Providing Centre Table/ Corner Table/ tepoi: 9.00 No. 5999.40
600X600X400mm having l6mm BWR plywood top
with premium laminate on top with L shaped post
formed legs made from 16mm both side Plywood
Lamination on both side with fabrication for joining
with each other.All edges are covered with 1mm PVC
edge bands glued by hot melt glue on automatic edge
bending machine ,as specifed in specification sheet,as
per direction of engineer incharge.
219 Providing and fixing Transparent Notice Board, of size 4.00 No. 5090.40
1000 X 600 X 150 mm ,19mm plywood both side
laminated Plywoods with 8 mm thick glass shutter
with locking arrangement having provision of hanging
on wall with necessary fittings and fabrication for
joining with each other as specifed in specification
sheet,as per direction of engineer incharge.
Item Rate In
Description of Item Quantity Unit Amount
No figures
220 P & F Library Glass Door Rack ready to assemble type, 20.00 No. 28482.00
self standing having over all size 1600X2100X400mm.
Entire construction is from 16mm calibrated BWR
Plywood covered with 1 mm premium laminate and
fabricated for joining system.Glass door are made
from sliding system of ARISTO Aluminium anodised
profile section and 10 mm toughened glass, As
detailed in attached specification sheet, as specifed in
specification sheet,as per direction of engineer
221 Providing and install Zebra Roller Blind curtains, sized 1051.00 Sqmt 1927.59
as per window dimensions, featuring 0.53mm thick
Zebra Curtain Fabric, a 1.25mm thick non-rusting
Aluminum Alloy Top Channel, a 1.50mm thick and
21mm diameter Aluminum Alloy Bottom Channel, and
a Plastic Tilt Channel with a 1.50mm Polyester cord
and 4.50mm cord balls with a stop lock mechanism.
This includes all necessary fixtures, fasteners, fittings,
labor, materials, and machinery for complete
installation according to approved drawings and
engineer's instructions
222 Providing and fixing kitchen base furniture below 11.00 Sqmt 20326.25
platform of depth 550 mm and height 750 mm,
fabricated from 18 mm thick BWR plywood
conforming to IS 303, finished with high-pressure
laminate on both internal and external surfaces,
bonded with approved adhesive, including edge
banding on all exposed edges. The unit shall comprise
modular cabinets with shutters, internal shelves,
partitions, and drawers as required, complete with all
necessary hardware such as SS hinges, telescopic
channels, handles, locks, magnetic catchers, and
fittings of approved quality. The carcass shall be
properly supported and aligned, resting on 100 mm
high PVC adjustable levellers, with 100 mm snap-fit
PVC skirting provided at the bottom including rubber
gasket for protection and finish.
The work shall include all required elements such as
cut-outs and provisions for sink, plumbing, and service
lines, proper ventilation gaps, back paneling where
required, and complete alignment with the kitchen
platform. All components shall be neatly finished,
factory-cut, assembled, and installed to ensure
durability, functionality, and aesthetic appearance.
The complete job shall include all materials, labour,
Item Rate In
Description of Item Quantity Unit Amount
No figures
223 Providing and fixing S.S. perforated dust bins of size 260.00 Nos 1277.65
230 mm dia × 350 mm height, fabricated from
stainless steel perforated sheet of approved design
and pattern, with smooth finished edges and uniform
perforation as per specification. The bin shall be
complete with bottom support, rigid construction, and
matt/satin finish, suitable for indoor use. The item
shall include all necessary fabrication, finishing, and
placement as approved by the Engineer-in-Charge,
complete in all respects as per specification sheet and
directions of the Engineer-in-Charge.
224 Supplying & Placing Matress 4" thick with 60 +/-kg / 558.00 Nos 9332.40
cum density quilted with 12mm PU foam and testry
with minimum 5 years manufacture warranty & Non-
allergic Polyester Fibre Pillow 40X61 cm Recorn or
equivelent with cover and Polyester fibre Bolster
in specification sheet and as per direction of engineer
225 Supplying and placing in position single bed sheet 558.00 Nos 1333.20
with Pillow Cover of minimum size 2.24mtr. x
mtr. Quality, Colour, Print and make any of above shall
be as approved by Architect and Engineer-in-charge,as
specifed in specification sheet, as per direction of
engineer incharge.
226 Supplying and placing in position 'Solapuri Chorsa' of 558.00 Nos 999.90
minimum size 2.29mtr. x 1.37 mtr. Quality, Colour,
and Print shall be as approved by Architect and
Engineer-in-charge.
227 Supplying and placing in position Woolen Blanket of 558.00 No 833.25
minimum size 2.29mtr. x 1.37 mtr. Quality, Colour,
Print and make any of above shall be as approved by
Architect and Engineer-in-charge.
228 Providing and fixing S.S. (304 Grade) plate of size 300 558.00 No 553.28
x 25 x 2 mm with 5 hooks (Khinti) incl. all required
material & labour etc. complete as directed by
Engineer in charge.
229 Providing and fixing S.S. 304 grade mosquito net in 1052.00 Sqmt 5532.78
window openings of required size, comprising fine SS
mesh fixed in a rigid frame made from 38 × 25 mm
aluminium rectangular tube sections, including
provision for openable shutter of same material with
hinges, handle, and locking arrangement. The frame
shall be properly fixed to the window with necessary
fasteners and accessories, with mesh neatly fixed
using beading, complete with all fittings, fabrication,
and installation in anodized/powder-coated finish, as
per specifications and direction of the Engineer-in-
Item Rate In
Description of Item Quantity Unit Amount
No figures
230 Providing and fixing storage rack of size 0.90 m 25.00 No 9999.00
(width) × 2.10 m (height) × 0.45 m (depth), designed
as ready-to-assemble type, suitable for self-standing,
overhanging, or partition-mounted installation,
fabricated from 18 mm thick both side pre-laminated
BWR grade plywood conforming to relevant
standards. The unit shall include necessary vertical
and horizontal members, intermediate shelves, and
back support as required for structural stability. All
exposed edges shall be finished with approved PVC
edge banding. The rack shall be complete with all
necessary hardware, fittings, and fixing arrangements
including cutting, edge finishing, assembling, and
installation, as per specifications and direction of the
Engineer-in-Charge.
231 Providing and fixing office table of size 2100 × 1050 × 1.00 No 42218.00
750 mm, fabricated from BWR plywood conforming to
IS 303, with 38 mm thick table top (made from built-
up sections) finished with 1.0 mm thick laminate on all
exposed surfaces and 0.8 mm laminate on inner
surfaces, with edge banding using hot-melt glue. The
apron, side panels, gable ends, modesty panel, and
drawer unit shall be made from 18 mm thick BWR
plywood, while drawers shall be made from 12 mm
thick plywood with proper bottom support. The table
shall include a side drawer unit with shutter, complete
with telescopic drawer channels, keyboard tray with
sliding channels, SS handles of size approx. 150 mm,
locks, hinges, screws, and all necessary fittings.The
structure shall include adequate vertical and
horizontal supports for rigidity and stability, with
proper internal framing as required. All exposed edges
shall be neatly finished, and all components shall be
properly aligned, assembled, and fixed. The item shall
include all materials, hardware, accessories,
fabrication, polishing/lamination, and installation
complete in all respects, as per specifications and
directions of the Engineer-in-Charge.
Total A
232 Point wiring for Light / Bell with 2-1.5 sq.mm & 2051.00 Pt 611.91
earth wire of 1.5 sq.mm (Green) both are of ISI marked
1.1 kV grade FRLSH PVC insulated multi strand copper
wires up to 10 mtr length , in below type of pipe
erected with 6A Modular type switch / bell push &
accessories and earth continuity of following type,
erected on PVC / Metallic/Wooden box, single
mounting base frame covered with
textured/metallic/white front plate modules erected
on / in wall / ceiling as per pipe erected, with
necessary Lamp holder/ceiling rose / H.D.Connector
as directed. (f) with medium class Rigid PVC pipe and
accessories erected concealed in wall/ceiling
complete Cat.III
Item Rate In
Description of Item Quantity Unit Amount
No figures
233 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 692.00 Pt 849.46
1.5 sq.mm (Green) both are of .ISI marked 1.1 kV
Grade FRLSH PVC insulated multi strand copper wires
up to 10 mtr length, in below type of pipe erected
with 6A Modular type switch and hum free EME step
type electronic fan regulator mounted and
accessories with earth continuity of following type
erected on PVC / Metallic/Wooden box, single
mounting base frame covered with
textured/metallic/white front plate modules erected
on / in wall / ceiling as per pipe erected. with
necessary ceiling rose / H.D.Connector as directed. (f)
with medium class Rigid PVC pipe and accessories
erected concealed in wall/ceiling complete Cat. III
234 Point wiring for on board Looped Plug with 6A 701.00 Pt 324.51
Modular type switch & 5 pin socket erected on PVC /
Metallic/Wooden box, single mounting base frame
covered with textured / metallic/white front plate
modules erected on / in wall / ceiling with following
type accessoriesCat. III
235 Point wiring for Two Way Controlled Light Point with 48.00 Pt 761.44
2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both
are of .ISI marked 1.1 kV grade FRLS PVC insulated
multi strand copper wires erected in below type of
pipe with 6A Modular type switches and following
type of accessories erected on PVC / Metallic/Wooden
box, single mounting base frame covered with
textured / metallic/white front plate modules erected
on / in wall / ceiling as per pipe erected. with
necessary batten/angle holder or ceiling rose or
H.D.Connector as directed. (f) with medium class Rigid
PVC pipe and accessories erected concealed in
wall/ceiling complete Cat. III
236 Providing following type of Modular Type Accessories 116.00 Nos 151.50
mounted with PVC / metallic/Wooden box, single
mounting base frame covered with textured /
metallic/white front plate , modules erected with
necessary connections as per site situation directed by
Engineer In charge. (1)One No. SP 6 Amp.Cat.III
237 Providing following type of Modular Type Accessories 116.00 Nos 151.50
mounted with PVC / metallic/Wooden box, single
mounting base frame covered with textured /
metallic/white front plate , modules erected with
necessary connections as per site situation directed by
Engineer In charge. (2) One No 5 pin plug Cat.III
Item Rate In
Description of Item Quantity Unit Amount
No figures
238 Providing following type of Modular Type Accessories 200.00 Nos 25.25
mounted with PVC / metallic/Wooden box, single
mounting base frame covered with textured /
metallic/white front plate , modules erected with
necessary connections as per site situation directed by
Engineer In charge. (7) Blank Plate Single Cat.III
239 Providing following type of Modular Type Accessories 2.00 Nos 160.59
mounted with PVC / metallic/Wooden box, single
mounting base frame covered with textured /
metallic/white front plate , modules erected with
necessary connections as per site situation directed by
Engineer In charge. (3) Two Pin/RJ-11 Telephone
Socket[A] For One Gang Cat.III
240 Providing following type of Modular Type Accessories 2.00 Nos 160.59
mounted with PVC / metallic/Wooden box, single
mounting base frame covered with textured /
metallic/white front plate , modules erected with
necessary connections as per site situation directed by
Engineer In charge. (8) Computer RJ-45 socket
241 Providing following type of Modular Type Accessories 240.00 Nos 180.79
mounted with PVC / metallic/Wooden box, single
mounting base frame covered with textured /
metallic/white front plate , modules erected with
necessary connections as per site situation directed by
Engineer In charge. (9) 16 Amp. SP one way switch
242 Providing following type of Modular Type Accessories 240.00 Nos 199.98
mounted with PVC / metallic/Wooden box, single
mounting base frame covered with textured /
metallic/white front plate , modules erected with
necessary connections as per site situation directed by
Engineer In charge. (10) 6/16Amp. Universal socket
243 Providing following type of Modular Type Accessories 2.00 Nos 151.50
mounted with PVC / metallic/Wooden box, single
mounting base frame covered with textured /
metallic/white front plate , modules erected with
necessary connections as per site situation directed by
Engineer In charge. (11) 6 Amps. Bell Push Cat.III
244 Providing and erecting ISI mark Medium class RIGID 2000.00 Mtr 24.24
PVC PIPES of following size complete to be erected
on/in wall or ceiling erected with necessary PVC
fittings & Junction boxes fixed with adhesive solution
& Clamps with following dia of pipes, in approved
manner as directed (a)20 mm
Item Rate In
Description of Item Quantity Unit Amount
No figures
245 Providing and erecting ISI mark Medium class RIGID 2500.00 Mtr 33.33
PVC PIPES of following size complete to be erected
on/in wall or ceiling erected with necessary PVC
fittings & Junction boxes fixed with adhesive solution
& Clamps with following dia of pipes, in approved
manner as directed (2) 25 mm
246 Providing and erecting ISI mark Medium class RIGID 2000.00 Mtr 54.54
PVC PIPES of following size complete to be erected
on/in wall or ceiling erected with necessary PVC
fittings & Junction boxes fixed with adhesive solution
& Clamps with following dia of pipes, in approved
manner as directed (c) 32 mm
247 Providing & erecting PVC Corrugated Flexible Conduit 240.00 0.00 17.17
with required nos. of coupling, PVC bushes, Check-nuts
etc. complete of following sizes. (a)20 mm
248 Providing & erecting PVC Corrugated Flexible Conduit 240.00 0.00 21.21
with required nos. of coupling, PVC bushes, Check-nuts
etc. complete of following sizes. (2) 25 mm
249 Providing & erecting PVC Corrugated Flexible Conduit 240.00 0.00 27.27
with required nos. of coupling, PVC bushes, Check-nuts
etc. complete of following sizes. (c) 32 mm
250 Providing and erecting Mains with 1.1 kV grade FRLSH 1600.00 Mtr 82.72
PVC insulated ISI marked stranded Copper conductor
wire in following type of pipe to be erected concealed
in /flushed on wall/ceiling, with 1.5 sq. mm copper
conductor FRLSH PVC insulated stranded wire of
green colour for earth continuity of following size (A)
With medium class Rigid PVC pipe and accessories (a)
2 wire 1.5 sq. mm
251 Providing and erecting Mains with 1.1 kV grade FRLSH 7220.00 Mtr 109.23
PVC insulated ISI marked stranded Copper conductor
wire in following type of pipe to be erected concealed
in /flushed on wall/ceiling, with 1.5 sq. mm copper
conductor FRLSH PVC insulated stranded wire of
green colour for earth continuity of following size (A)
With medium class Rigid PVC pipe and accessories (b)
2 wire 2.5 sq. mm
252 providing and erecting Mains with 1.1 kV grade FRLS 15200.00 Mtr 147.41
PVC insulated ISI marked stranded Copper conductor
wire in following type of pipe to be erected in / on
wall / ceiling with 2.5 sq. mm copper conductor FRLS
PVC insulated stranded wire of green colour for earth
continuity of following size(A) with medium class
Rigid PVC pipe and accessories (a) 2 wire 4 sq. mm
Item Rate In
Description of Item Quantity Unit Amount
No figures
253 providing and erecting Mains with 1.1 kV grade FRLS 320.00 Mtr 194.07
PVC insulated ISI marked stranded Copper conductor
wire in following type of pipe to be erected in / on
wall / ceiling with 2.5 sq. mm copper conductor FRLS
PVC insulated stranded wire of green colour for earth
continuity of following size(A) with medium class
Rigid PVC pipe and accessories (b) 2 wire 6 sq. mm
254 providing and erecting Mains with 1.1 kV grade FRLS 1750.00 Mtr 558.88
PVC insulated ISI marked stranded Copper conductor
wire in following type of pipe to be erected in / on
wall / ceiling with 2.5 sq. mm copper conductor FRLS
PVC insulated stranded wire of green colour for earth
continuity of following size(A) with medium class
Rigid PVC pipe and accessories (i) 4 wire 10 sq.
mm(use earth wire of 4 sq.mm
255 providing and erecting Mains with ISI marked, 1.5kV 360.00 Mtr 177.76
grade electrolyte multi stranded, annealed copper
conductor with heat resistant PVC insulated conforms
to IS 694, IEC - 227 erected in existing pipe of
following size (Specifically for control panel, relays,
power switchgears, motor starters & control wiring)
with required size of copper lugs, nuts and bolts if
required. (g) One wire 16.00 sq. mm
256 providing and erecting Mains with ISI marked, 1.5kV 80.00 Mtr 376.73
grade electrolyte multi stranded, annealed copper
conductor with heat resistant PVC insulated conforms
to IS 694, IEC - 227 erected in existing pipe of
following size (Specifically for control panel, relays,
power switchgears, motor starters & control wiring)
with required size of copper lugs, nuts and bolts if
required. (i) One wire 35.00 sq. mm
257 providing and erecting Mains with ISI marked, 1.5kV 50.00 Mtr 588.83
grade electrolyte multi stranded, annealed copper
conductor with heat resistant PVC insulated conforms
to IS 694, IEC - 227 erected in existing pipe of
following size (Specifically for control panel, relays,
power switchgears, motor starters & control wiring)
with required size of copper lugs, nuts and bolts if
required. j) One wire 50.00 sq. mm
258 providing and erecting Mains with ISI marked, 1.5kV 90.00 Mtr 1149.38
grade electrolyte multi stranded, annealed copper
conductor with heat resistant PVC insulated conforms
to IS 694, IEC - 227 erected in existing pipe of
following size (Specifically for control panel, relays,
power switchgears, motor starters & control wiring)
with required size of copper lugs, nuts and bolts if
required. (l) One wire 95.00 sq. mm
Item Rate In
Description of Item Quantity Unit Amount
No figures
259 Supplying and erecting Flexible PVC insulated multi 300.00 Mtr 58.58
strand multi core 1.1 kV grade ISI marked copper
wires of following size to be erected as directed.(e)
1.50 Sq.mm 3 core round PVC sheathed
260 Providing & erecting Switch board for Computer or 520.00 Nos 1133.22
electric apparatus consisting of following modular
type accessories mounted with PVC / Metallic
concealed/open box with single mounting base frame
covered with textured/metallic /white front
plate,modules erected with necessary connections as
1 no. 6A/16A universal plug-switch combined.
3 nos. 6A Switch
3 nos. 6A 5 pin Plug For Modular Type Accessories
261 Decorative call bell Ting-tong box type 250 volts 2.00 Nos 71.71
complete erected
262 Supplying and erecting LED indoor fittings with LEDs 920.00 Nos 535.30
of wattage 0.2 Watt to 0.5 Watt assembled on single
MCPCB, with housing used as a heat sink shall be
made of thick sheet Steel conforming to IS: 513/CRCA/
aluminium die cast powder coated and high U.V. &
corrosion resistance with diffuser with company
mark/name 160V to 270V, Power Factor more than
CCT 3000 K to 6500K,
Luminaire efficacy> 85 lumens/watt ,LED
LED driver efficiency > 85 %
( fitting required LM-79 & LM-80 Certificates)(NOTE:
Below description have shown ranges of Wattage
capacity of LED fittings.The Engineer incharge may
shown.)(A) Tube Light with integral driver (v) 36-40
Watts, Surge-2 KV, IP-20, conventional 4 feetCat-lll
263 Supplying and erecting led lamps with following 221.00 Nos 69.69
wattage capacity of 220 to 240 voltage, minimum
15000 burning hours life, 500 V in built-surge
protection,Polycarbonate diffuser, mounting suitable
for E14 / E27 / B22 lamp holders, pf >= 0.5 (A) LED
Lamps integral type, with PC diffuser suitable LAMP
holder(i) 2 to 3 watts Cat-III
264 Supplying and erecting led lamps with following 252.00 Nos 112.11
wattage capacity of 220 to 240 voltage, minimum
15000 burning hours life, 500 V in built-surge
protection,Polycarbonate diffuser, mounting suitable
for E14 / E27 / B22 lamp holders, pf >= 0.5 (A) LED
Lamps integral type, with PC diffuser suitable LAMP
holder(ii) 5 to 8 watts Cat-III
Item Rate In
Description of Item Quantity Unit Amount
No figures
265 Supplying and erecting LED indoor fittings with LEDs 369.00 Nos 427.23
of wattage 0.2 Watt to 0.5 Watt assembled on single
MCPCB, with housing used as a heat sink shall be
made of thick sheet Steel conforming to IS:
513/CRCA/aluminium pressure die cast powder
coated and high U.V. & corrosion resistance with
diffuser housed in aluminium casted body with
company mark/name
160V to 270V,Power Factor more than 0.95, THD <
CCT 3000 K to 6500K,
Luminaire efficacy> 85 lumens/watt
LED driver efficiency > 85 %
( fitting required LM-79 & LM-80 Certificates)(NOTE:
Below description have shown ranges of Wattage
capacity of LED fittings.The Engineer incharge may
shown.) (A) Square/ Circular shaped
Surface/Recessed Mount Downlight with provision for
spring loaded mounting clips complete.IP20(ii) 11-15
watts, Surge-2 KVCat-lll
266 Supplying and erecting LED street light / Flood light 35.00 Nos 5080.30
fittings with High power White LEDs wattage of
Watt and above assembled on single MCPCB, efficiency
more than 130 lm/w and corrosion free High pressure
die cast aluminum housing with smooth finish powder
coated and heat sink extruded aluminium with diffuser
and Polycarbonate optics/ lenses, with toughened
glass with company mark/name engraved or
embossed 160 to 270 V,Power Factor more than 0.95,
THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio
>0.45, Luminaire efficacy> 100 lumens/watt . LED
driver efficiency > 85 %.( fittings required LM-79 &
LM-80 certificates)(NOTE: Below description have
shown ranges of Wattage capacity of LED fittings.The
between the ranges shown.)(A) Street Light (IP-65),
Surge protection -4KV integral and ,Light must have
440VAC line supply with over-voltage protection.(iii)
60 - 89 wattsCat-lll
Item Rate In
Description of Item Quantity Unit Amount
No figures
267 Supplying and erecting LED street light / Flood light 16.00 Nos 9196.05
fittings with High power White LEDs wattage of
Watt and above assembled on single MCPCB, efficiency
more than 130 lm/w and corrosion free High pressure
die cast aluminum housing with smooth finish powder
coated and heat sink extruded aluminium with diffuser
and Polycarbonate optics/ lenses, with toughened
glass with company mark/name engraved or
embossed 160 to 270 V,Power Factor more than 0.95,
THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio
>0.45, Luminaire efficacy> 100 lumens/watt . LED
driver efficiency > 85 %.( fittings required LM-79 &
LM-80 certificates)(NOTE: Below description have
shown ranges of Wattage capacity of LED fittings.The
between the ranges shown.) (B) Flood Light (IP-65),
Surge protection -4KV integral and ,Light must have
440VAC line supply with over-voltage protection(vii)
above 200 to 250 wattsCat-lll
268 Supplying and erecting LED street light / Flood light 10.00 Nos 4096.56
fittings with High power White LEDs wattage of
Watt and above assembled on single MCPCB, efficiency
more than 130 lm/w and corrosion free High pressure
die cast aluminum housing with smooth finish powder
coated and heat sink extruded aluminium with diffuser
and Polycarbonate optics/ lenses, with toughened
glass with company mark/name engraved or
embossed 160 to 270 V,Power Factor more than 0.95,
THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio
>0.45, Luminaire efficacy> 100 lumens/watt . LED
driver efficiency > 85 %.( fittings required LM-79 &
LM-80 certificates)(NOTE: Below description have
shown ranges of Wattage capacity of LED fittings.The
between the ranges shown.) (C) Post Top Lantern LED
fitting comprises of finish cast aluminum spigot and
spun aluminum canopy fixed with opal polycarbonate,
pipe arrangement for vertical mounting driver and
accessories wired upto terminal block.IP 65(ii)32-40W
269 Providing and erecting Approved make Four pole 47.00 Nos 6790.23
moulded case circuit breaker having breaking capacity
ICU of 25 KA. at 415 V,having normal current rating up
to 25 A to 100A. with Fixed thermal & magnetic
release suitable to work on A.C. supply 50 c/s. with all
internal connections, spreader tinned copper &
complete erected in existing 16 G.M.S. housing.
ICS=100% of ICU only Cat III
Item Rate In
Description of Item Quantity Unit Amount
No figures
270 Providing and erecting Approved make Four pole 9.00 Nos 8861.74
moulded case circuit breaker having breaking capacity
ICU of 35 KA. at 415 V. having normal current rating
125A. with Fixed thermal & magnetic release suitable
to work on A.C.supply 50 Hz. with all internal
connections, spreader tinned copper & complete
erected in existing 16 G.M.S. housing. ICS=100% of
ICU only Cat III
271 Providing and erecting Approved make Four pole 26.00 Nos 23041.13
moulded case circuit breaker having breaking capacity
ICU of 35 KA. and above at 415 V . having normal
current rating 250A. with variable thermal &
magnetic release suitable to work on A.C.supply
c/s. with all internal connections, spreader tinned
copper & complete erected in existing 16 G.M.S.
housing. ICS=100% of ICU only Cat III
272 Providing and erecting Approved make Earth fault 2.00 Nos 5956.98
Relay suitable to mount with inter connection suitable
to following size of moulded case circuit breaker
having CT ratio & MCCB rating as following along with
shunt trip 220V AC. with all internal connections &
complete erected in existing M.S.housing.. (3) 250 A -
400 A , CT Ratio 1/400
273 Approved make standard Draw out type 4 Pole Air 3.00 nos 165024.91
circuit breaker. Having 50 kA breaking capacity with
ICU=ICS=ICW (1 sec)Vsr=690 v, Ui=1kv ,impulse
voltage=12 kv with following type of relay and
accessories.
(1) Manual Draw out type (MDO) with following type
of relay system
(B) with microprocessor Release with over load, short
circuit, earth fault protection and metering display in
modular design with LED display and Test Trip button
facility, CTs and auxiliary contacts, of following
current ratings. (2) Add Rs. 30500.00 in above said
item for Electrically Draw out type (EDO) type in place
of manual draw out (MDO)
(i) 800 Amp 50 kA Cat III
274 Supplying & erecting approved make Four Pole 415V 1.00 Nos 35607.55
change over switch interior for panel mounting with
operating mechanism A.C.23 duty confirming to IS for
(H)800A ,Cat-III
275 Providing and erecting following additional parts for 82.00 Nos 961.52
panel mounting MCCBs (A)Extended operating rotary
handle with pad lock with three position trip,off,on
suitable for 25A to 250 A panel mounting cat-III
Item Rate In
Description of Item Quantity Unit Amount
No figures
276 Supplying and erecting triple pole & neutral 440V / 25.00 Rn.Mtr 1961.42
500V panel mounting Copper Busbars with four equal
Nos. of electrolyte bus having current density not
more than 1.6 Amp. / sq.mm (Rated current / cross
section area) duly wrapped with colour insulating tape
for phase sequence of following current carrying
capacity, erected with necessary bus bar supports
/insulators, main cable socket to each bar, erected in
existing cubical panel with necessary connections. (A)
Suitable for 100 Amp. Capacity
277 Supplying and erecting triple pole & neutral 440V / 20.00 Rn.Mtr 4909.61
500V panel mounting Copper Busbars with four equal
Nos. of electrolyte bus having current density not
more than 1.6 Amp. / sq.mm (Rated current / cross
section area) duly wrapped with colour insulating tape
for phase sequence of following current carrying
capacity, erected with necessary bus bar supports
/insulators, main cable socket to each bar, erected in
existing cubical panel with necessary connections. (C)
Suitable for 300 Amp. capacity
278 Supplying and erecting triple pole & neutral 440V / 10.00 Rn.Mtr 13199.69
500V panel mounting Copper Busbars with four equal
Nos. of electrolyte bus having current density not
more than 1.6 Amp. / sq.mm (Rated current / cross
section area) duly wrapped with colour insulating tape
for phase sequence of following current carrying
capacity, erected with necessary bus bar supports
/insulators, main cable socket to each bar, erected in
existing cubical panel with necessary connections. (F)
Suitable for 800 Amp. capacity
279 providing and erecting Miniature circuit breaker 61.00 nos 297.95
single pole 0.5A to 2A system and having breaking
capacity 10 KA to be erected in existing box.
confirming to IS 8828/1996 with ISI Mark Cat.III
280 providing and erecting Miniature circuit breaker 638.00 nos 123.22
single pole 6A to 25A suitable to operate on 240 V A.C.
system and having breaking capacity 10 KA to be
erected in existing box. confirming to IS 8828/1996
with ISI Mark Cat.III
281 Providing & erecting 240 V MCB double pole switch 49.00 Nos 362.59
for motor & inductive load (C Curve) having 10 KA
breaking capacity & confirms to IS : 8828 in existing
box having following capacity (B) 40 Amp. Cat-III
282 Providing & erecting 415 V MCB Four Pole for Motor 68.00 Nos 811.03
& Inductive Load (C Curve) having 10KA breaking
capacity & confirms to IS :8828 in existing box having
following capacity (c) 63 Amp.Cat.III
283 Sheets steel powder coated enclosure suitable for 6.00 Nos 176.75
incorporating One/Two nos. MCB.
Item Rate In
Description of Item Quantity Unit Amount
No figures
284 Providing and erecting Sheet Steel powder coated 11.00 Nos 1062.92
MCB distribution board - flush / surface mounted
fitted with busbar, neutral link, earth bar and DIN rail,
Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without
MCB to house appropriate nos. of MCBs.(The DBs
should be used of same company of MCB to be used)
suitable for ADD 20% more for concealed erection of
distribution board. 3-11- 5 to 3-11-8. (A) single
phase incoming and horizontal single phase
outgoingb) sheet steel double door (IP-43))(iii6 way
285 Providing and erecting Sheet Steel powder coated 33.00 Nos 4095.35
MCB distribution board - flush / surface mounted
fitted with busbar, neutral link, earth bar and DIN rail,
Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without
MCB to house appropriate nos. of MCBs.(The DBs
should be used of same company of MCB to be used)
suitable for ADD 20% more for concealed erection of
distribution board. 3-11- 5 to 3-11-8. B) three phase
incoming and single phase horizontal type outgoing
Per phase isolation type (PPI) (b) sheet steel double
door (ii)8 way
286 providing and erecting Approved make RCCBs 112.00 Nos 2166.45
conforming to IS: 12640 and having sensitivity of
mA and Short Circuit withstand capacity of 10 KA and
suitable for operation on single phase 240 V,50Hz.
having characteristic of quick action & tripping with
all advance feature & do not incorporate any
electronic component. for following Max. rating
erected as directed (i) 25 Amps.DP
287 Providing and erecting metallic vitrified danger notice 30.00 Nos 69.69
board as per language suggested by engineer incharge
for MEDIUM VOLTAGE installation to be erected as per
288 Providing and erecting Annealed bare Copper wire 200.00 Kg 794.87
289 Providing and erecting required size Copper strip for 200.00 Kg 794.87
earthing of H.T. OCB / ACB/ Transformer, LT panel
board, Motors etc. using copper clamp.
290 Providing and erecting Pipe type earthing having 150 33.00 Nos 368.65
cms.long and 2.5 cms. dia. galvanised iron pipe with
coupling and buch buried in specially prepared earth
pit complete with necessary 8 SWG earth wire.
291 For using salt and charcoal / coke as required for pipe 33.00 nos 171.70
type earthing.
Item Rate In
Description of Item Quantity Unit Amount
No figures
292 Supplying & erecting in earthpit of minimum bore dia. 1.00 Nos 5842.85
225mm size approved make Safe Earthing Electrode
consisting Pipe-in-Pipe Technology as per IS 3043-
1987 made of corrosion free hot dipped G.I.Pipes
having Outer pipe dia of 80 mm having 80-200 Micron
galvanising, Inner pipe dia of 40 mm having 200-250
Micron galvanising, connection terminal dia of
mm with constant ohmic value surrounded by highly
conductive compound with high charge dissipation
suitable for following type of applications with
chamber and heavy duty cover (A)(approved make
OEM has to submit test certificate including value of
earth resistance of installation duly stamped and
signed by agency and officer Incharge has to ensure
the value of earthing resistane mentioned in test
Certificate) & having back filling compound of (B)
Inner chemical (CCM Compound)- Resistivity:-
ohm / meter testing as per IEC 62561-2017, Voltage
drop:- < 1 volt at no load & dry form, Sulphar content:-
<2%(C) Back fill Compound :- Earthing compound
should be capable to retain moisture for long time
Necessary test report must be submitted by Agency.
[A] For electrical installation up to 440 V
Length of Pipe - 1 Mtr
Back filling compound - 1 Nos. of Bag of 15 Kgs.
293 [C] For Electrical Installation covering Transformer 27.00 Nos 10593.89
Neutrals, Lightning arrester Earthing, A.C.Plant &
Sensitive Computer System(like Automation,
SCADA)i.e. independent Earthing located in other
than normal soil i.e. Soft Rock, Marshy Soil etc..
-Length of Pipe : 3 Mtrs.
-Back filling Compound :2 nos Bags of 25 Kg.
Item Rate In
Description of Item Quantity Unit Amount
No figures
294 Providing & erecting weather proof, dust & vermin 24.00 Sq.Mtr 14902.55
proof, floor mounted front operated indoor type
cubical panel board necessary IP-42 and above
protection as per approval from engineer incharge
made from 14 SWG thick CRC M.S. sheet for outer body
& doors, 16 SWG thick CRC M.S.sheet for internal
partitions with necessary accesories , supporting
angles/ flats channel including cutting, bending,
drilling, welding, riveting with internal partitions &
cable alley as per requirements & instruction of
engineer-in-charge with erection of supplied switch
gears, BUSBARS, suitable size of inter connecting PVC
copper wire / copper-aluminium strips, rubber
grommets, rib, bakelite control fuses/MCB for
measuring instruments, earth bus & earth bolts,
foundation flange - bolts-base Plates, sufficient nos. of
hinged doors, handles with locking arrangement and
rubber gasket,heavy duty end terminal
connection,danger notice board,necessary
ventilation,earthing strip complete. The Panel shall be
painted with epoxy powder coating. (The rates
excludes the cost of switchgears, bus bars, inter
connecting mains & Copper Aluminium strips, meters,
Fuses etc. The dimension shall be measured excluding
295 Providing & erecting weather proof, dust & vermin 14.00 Sq.Mtr 40999.94
proof, floor mounted front operated indoor type
cubical panel board necessary IP-42 and above
protection as per approval from engineer incharge
made from 14 SWG thick CRC M.S. sheet for outer body
& doors, 16 SWG thick CRC M.S.sheet for internal
partitions with necessary accesories , supporting
angles/ flats channel including cutting, bending,
drilling, welding, riveting with internal partitions &
cable alley as per requirements & instruction of
engineer-in-charge with erection of supplied switch
gears, BUSBARS, suitable size of inter connecting PVC
copper wire / copper-aluminium strips, rubber
grommets, rib, bakelite control fuses/MCB for
measuring instruments, earth bus & earth bolts,
foundation flange - bolts-base Plates, sufficient nos. of
hinged doors, handles with locking arrangement and
rubber gasket,heavy duty end terminal
connection,danger notice board,necessary
ventilation,earthing strip complete. The Panel shall be
painted with epoxy powder coating. (The rates
excludes the cost of switchgears, bus bars, inter
connecting mains & Copper Aluminium strips, meters,
Fuses etc. The dimension shall be measured excluding
Item Rate In
Description of Item Quantity Unit Amount
No figures
296 Providing , erecting , fabricating the M.S. structure as 800.00 Kg 77.77
per requirement on site incorporating proper size of
M.S. angles,square,round, flats, bars, channels, sections
complete with cutting, welding, grinding & finishing
duly painted with one coat of red oxide with erection
on site as per direction of engineer in charge with
necessary grouting, cementing, plastering & finishing
297 Providing and erecting multifunctional meter suitable 15.00 nos 14123.84
for application of Power monitoring and showing
measurement of following Voltage, Frequency,
Apparent energy, Apparent power, Active and reactive
energy, Active and reactive power, Average voltage
Vavg, Peak demand power PM, QM, SM, Demand
power P, Q, S, Apparent power S, S1, S2, S3, Unbalance
current, Power factor and displacement PF (signed,
four quadrant), Calculated neutral current, Active,
reactive, apparent energy (signed, four quadrant),
Active power P, P1, P2, P3, Voltage U21, U32, U13, V1,
V2, V3, Phase currents, Average current Iag, Peak
demand currents, Reactive power Q, Q1, Q2, Q3,
Demand current I1, I2, I3, [Us] rated supply voltage
40...300 V AC 45...65 Hz, 40...300 V DC, Network
frequency 50 Hz, Type of network 3P, Display type
segments LED, Display colour Red, Messages display
capacity 3 fields of 4 characters, Display digits
digit(s) - 14.2 mm in height
298 Providing and erecting FRLSH-XLPE(IS:7098)(I)-88 ISI 200.00 Mtr 477.23
armoured cable multistrand Aluminium conductor for
1.1 kV. to be laid on wall with necessary clamps or in
existing trench / pipe of following size of cables (D)
1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)
299 Providing and erecting FRLSH-XLPE(IS:7098)(I)-88 ISI 900.00 Mtr 1140.04
armoured cable multistrand Aluminium conductor for
1.1 kV. to be laid on wall with necessary clamps or in
existing trench / pipe of following size of cables (H)
1/2 core 185 Sq. mm ( 95 Sq. mm 1/2 core)
300 Providing and erecting FRLSH-XLPE(IS:7098)(I)-88 ISI 300.00 Mtr 1774.22
armoured cable multistrand Aluminium conductor for
1.1 kV. to be laid on wall with necessary clamps or in
existing trench / pipe of following size of cables (J)
1/2 core 300 Sq.mm ( 150 Sq. mm 1/2 core)
301 Providing and erecting FRLSH-XLPE (IS:7098)(I)-88 700.00 Mtr 159.08
ISI armoured cable multistrand / Solid Aluminium
conductor for 1.1 kV. to be laid on wall with
necessary clamps or in existing trench / pipe of
following size of cables(B) 4 core 6 Sq. Mm
Item Rate In
Description of Item Quantity Unit Amount
No figures
302 Providing and erecting FRLSH-XLPE (IS:7098)(I)-88 100.00 Mtr 194.07
ISI armoured cable multistrand Aluminium conductor
for 1.1 kV. to be laid on wall with necessary clamps or
in existing trench / pipe of following size of cables (B)
4 core 16 Sq. mm
303 Providing and erecting FRLSH-XLPE (IS:7098)(I)-88 400.00 Mtr 240.73
ISI armoured cable multistrand Aluminium conductor
for 1.1 kV. to be laid on wall with necessary clamps or
in existing trench / pipe of following size of cables (B)
4 core 25 Sq. mm
304 Making trench in soft soil of suitable width of 90 cm 1200.00 Mtr 55.55
deep for laying cable or locating the fault all over the
run and back filling the same and making the surface
as normal ground.
305 Providing & laying. R.C.C. Hume pipe for cable to be 200.00 Mtr 456.52
laid 90 cm. below ground across the road crossing or
on floor with necessary material in an approved
manner and making the ground as per original.(A)
306 Providing & laying approved make ISI marked Rigid 50.00 Mtr 236.34
PVC pipe having 6Kg / cm2 (Class-3) to be erected at
road crossing on or floor as directed for laying of
cable. The pipes as following size of dia & weight per
mtr. (F) 110 mm inner Dia. (11.63 Kg/6 RMT)
307 Providing & laying approved make Double walled 600.00 Mtr 62.62
corrugated pipes (DWC) of polyethylene(conforming
to IS 14930 II )with necessary connecting accessories
of same material at required depth in existing trench
for laying of cable. below ground / road surface for
enclosing cable (A)50 mm outer dia
308 Providing & laying approved make Double walled 800.00 Mtr 95.95
corrugated pipes (DWC) of polyethylene(conforming
to IS 14930 II )with necessary connecting accessories
of same material at required depth in existing trench
for laying of cable. below ground / road surface for
enclosing cable (C))90 mm outer dia
309 Providing & laying approved make Double walled 400.00 Mtr 137.36
corrugated pipes (DWC) of polyethylene(conforming
to IS 14930 II )with necessary connecting accessories
of same material at required depth in existing trench
for laying of cable. below ground / road surface for
enclosing cable (D)120 mm outer dia.
310 Providing and, fixing heavy duty flange type brass 50.00 Nos 38.38
cable gland with rubber ring for PVC insulated
armoured cable complete with out going tails,
insulating tape etc for following size of cables. (B) 2 to
4 core 6 Sq. mm
311 Providing and, fixing heavy duty flange type brass 4.00 Nos 47.47
cable gland with rubber ring for PVC insulated
armoured cable complete with out going tails,
insulating tape etc for following size of cables. (D) 2 to
4 core 16 Sq. mm
Item Rate In
Description of Item Quantity Unit Amount
No figures
312 Providing and, fixing heavy duty flange type brass 8.00 Nos 51.51
cable gland with rubber ring for PVC insulated
armoured cable complete with out going tails,
insulating tape etc for following size of cables. (E) 2 to
4 core 25 Sq. mm
313 Providing and, fixing heavy duty flange type brass 16.00 Nos 103.02
double compression type cable gland with rubber
ring for PVC insulated armoured cable complete with
out going tails, insulating tape etc for following size of
cables. (C) 3 & 1/2 core 70 Sq. mm
314 Providing and, fixing heavy duty flange type brass 8.00 Nos 238.36
double compression type cable gland with rubber
ring for PVC insulated armoured cable complete with
out going tails, insulating tape etc for following size of
cables. (G) 3 & 1/2 core 185 Sq. mm
315 Providing and, fixing heavy duty flange type brass 8.00 Nos 280.78
double compression type cable gland with rubber
ring for PVC insulated armoured cable complete with
out going tails, insulating tape etc for following size of
cables. (I) 3 & 1/2 core 300 Sq. mm
316 Solder less crimping type Aluminium lugs conforming 200.00 Nos 6.06
to IS suitable for cable of following size evenly
crimped with high pressure tool & connected to
switchgear terminals with brass/cadmium plated nut
bolts in an approved manner. (A) 1.5/ 2.5/4/6 Sq.mm
317 Solder less crimping type Aluminium lugs conforming 48.00 Nos 15.15
to IS suitable for cable of following size evenly
crimped with high pressure tool & connected to
switchgear terminals with brass/cadmium plated nut
bolts in an approved manner. (C) 16/25 Sq.mm.
318 Solder less crimping type Aluminium lugs conforming 64.00 Nos 25.25
to IS suitable for cable of following size evenly
crimped with high pressure tool & connected to
switchgear terminals with brass/cadmium plated nut
bolts in an approved manner. (E) 70 Sq.mm.
319 Solder less crimping type Aluminium lugs conforming 32.00 Nos 80.80
to IS suitable for cable of following size evenly
crimped with high pressure tool & connected to
switchgear terminals with brass/cadmium plated nut
bolts in an approved manner. ( I ) 185 Sq.mm.
320 Solder less crimping type Aluminium lugs conforming 32.00 Nos 98.98
to IS suitable for cable of following size evenly
crimped with high pressure tool & connected to
switchgear terminals with brass/cadmium plated nut
bolts in an approved manner. (K) 300 Sq.mm.
Item Rate In
Description of Item Quantity Unit Amount
No figures
321 Solder less crimping type Copper lugs conforming to IS 164.00 Nos 10.10
suitable for cable of following size evenly crimped
with high pressure tool & connected to switchgear
terminals with brass/cadmium plated nut bolts in an
approved manner. (B) 10 Sq.mm
322 Providing and fixing approved make Perforated C type 50.00 Rmt 424.20
cable tray. Made from sheet steel. The cable tray
should be single or double bended as per required and
as per IS 2062/1079 and shall be coated with hot dip
galvanizing as per IS 2629/4759. with max 17.5%
perforation with coupler plate / Fish plate and GI
hardware like nut - bolt and washers etc. erection with
necessary support( included) as per Specification and
as per instruction of engineer in charge.. (3) 150 X
X 1.6 mm Thick
323 Providing and fixing approved make Perforated C type 300.00 Rmt 622.16
cable tray. Made from sheet steel. The cable tray
should be single or double bended as per required and
as per IS 2062/1079 and shall be coated with hot dip
galvanizing as per IS 2629/4759. with max 17.5%
perforation with coupler plate / Fish plate and GI
hardware like nut - bolt and washers etc. erection with
necessary support( included) as per Specification and
as per instruction of engineer in charge.. (5) 300 X
X 2.0 mm Thick
324 Providing and fixing approved make Perforated C type 100.00 Rmt 1195.84
cable tray. Made from sheet steel. The cable tray
should be single or double bended as per required and
as per IS 2062/1079 and shall be coated with hot dip
galvanizing as per IS 2629/4759. with max 17.5%
perforation with coupler plate / Fish plate and GI
hardware like nut - bolt and washers etc. erection with
necessary support( included) as per Specification and
as per instruction of engineer in charge.. (8) 750 X
X 2.0 mm Thick
325 Providing and fixing approved make Ladder type cable 80.00 Rmt 338.35
tray. Made from M.S sheet. The cable tray should be
bended as per IS 2062/1079 shall be fabricated of
double bended channel section longitudinal members
with single bended Channel section. Rungs of
members welded to the base of the longitudinal
members at 250 mm c/c spacing . as per IS and shall
be coated with hot dip galvanizing as per IS
2629/4759. with coupler plate / Fish plate and GI
hardware like nut - bolt and washers etc. erected on
existing support as per Specification and as per
instruction of engineer in charge..(4) 400 X 50 X
Item Rate In
Description of Item Quantity Unit Amount
No figures
326 Providing & erecting Approved make Power Saving 45 692.00 Nos 1948.29
- 50 Watt Ceiling Fan with double ball bearing ISI mark
with Condenser 230 volt A.C. 50 Hz 1200 mm sweep
complete having 3blades with aluminium blades with
canopy & 30 cm. down rod erected with
earthing.(Make shall be approved by Engineer in
327 Supplying and erecting 19 / 20 mm. nominal bore 484.40 Mtr 108.07
Medium Class M.S. Pipe down rod erected duly painted
for fan complete with proper insulation without
leakage and earthing.
328 Supplying & erecting fan hook box of 10 mm M.S. 692.00 Nos 108.07
round bar bounded to the RCC bars up to 50mm length
each side and pierced through a 16 Gauge M.S. box /
Heavy Duty PVC box complete erected concealed in
Ceiling with necessary finishing.
329 Providing 2.5mm.thick laminated acrylic sheet to 692.00 Nos 18.18
cover the fan hook or Fan box.
330 Supplying & erecting approved make low noise 244.00 Nos 1703.87
decorative exhaust fan having square frame ABS body
with inbuilt lowers & square frame.250mm with
RPM Cat.II
331 Supplying & erecting single phase approved make 76.00 nos 2054.34
industrial exhaust fan suitable for medium duty ring
mounted low noise operation suitable for medium
duty having following dia size and maximum speed in
RPM[A] 300-305 mm dia 900 RPM Cat-II
332 Providing suitable M.S. louver shutter of the Exhaust 76.00 Nos 368.65
333 Supplying and erecting approved make Octagonal pole 8.00 Nos 6111.51
made from HR sheet steel. The pole should be made as
per IS. and shall be coated with hot dip galvanizing as
per IS 2629/2633/4759, suitable suspend local wind
speed with integral Junction box consist of terminal
plate of min 6mm Hylam sheet, standard profile
35mmX7.5mm Din-Rail for MCB Mounting, stud type
terminal and arrangement for cable termination to be
erected With Suitable foundation (Included) as per
details given by manufacturer considering site
requirement. (B) 4 Mtr. Long 70 mm Top X 130 mm
bottom dia, 3 mm thickness with
200mmX200mmX12mm base plate, 4-M16 Bolts and
450mm long with necessary G.I. J Bolts .Approx weight
Item Rate In
Description of Item Quantity Unit Amount
No figures
334 Supplying and erecting approved make Octagonal pole 25.00 Nos 9011.22
made from HR sheet steel. The pole should be made as
per IS. and shall be coated with hot dip galvanizing as
per IS 2629/2633/4759, suitable suspend local wind
speed with integral Junction box consist of terminal
plate of min 6mm Hylam sheet, standard profile
35mmX7.5mm Din-Rail for MCB Mounting, stud type
terminal and arrangement for cable termination to be
erected With Suitable foundation (Included) as per
details given by manufacturer considering site
requirement. (D) 6 Mtr. Long 70 mm Top X 135 mm
bottom dia, 3 mm thickness with
200mmX200mmX12mm base plate, 4-M20 Bolts and
600mm long with necessary G.I. J Bolts .Approx Pole
weight 59 kg
335 Providing and erecting street light pole bracket 15.00 Nos 614.08
comprising main B Class GI pipe of 4.2 cm/require
outside dia. complete with suitable B Class G.I sleeve
tubing of approx. 45cms.length and suitable for
mm / 80mm. / require size pole top having sufficient
fasteners for fixing the brackets and having spread of
1 mtr. length with suitable rise as per site condition &
suitable welded stiffener reducer and nipple with
check nut complete painted with one coat of Red oxide
/ PU base primer and two coats of Aluminium / PU
paint. paint with following nos of arms. [A] Single Arm
bracket 1 Mtr
336 Providing and erecting street light pole bracket 10.00 Nos 829.21
comprising main B Class GI pipe of 4.2 cm/require
outside dia. complete with suitable B Class G.I sleeve
tubing of approx. 45cms.length and suitable for
mm / 80mm. / require size pole top having sufficient
fasteners for fixing the brackets and having spread of
1 mtr. length with suitable rise as per site condition &
suitable welded stiffener reducer and nipple with
check nut complete painted with one coat of Red oxide
/ PU base primer and two coats of Aluminium / PU
paint. paint with following nos of arms. [B] Double
Arm Bracket 1 Mtr
337 Supplying and erecting B class Galvanized iron pipe 40.00 Mtr 249.47
having smooth finished bore of the pipe on both ends
erected nuts and bolts along the pole / wall shaping
the pipe as per site requirement. Pipe dia as following.
(C) 40 mm dia.
Item Rate In
Description of Item Quantity Unit Amount
No figures
338 Supplying & erecting approved make Digital time 2.00 Nos 3168.37
switch having lithium cell 6 years operative and
operate battery backup 1 channel day clock with
memory programme, suitable to operate on 240V +
5%, 16A with, floating contacts Minimum switching
setup time 1 minimum & LCD display. Also comporised
permanent ON/OFF switching. Programming switches
& housed in fire proof thermoplastic enclosure &
transperent cover erected as required with necessary
connection erected as directed.
339 Supplying & erecting power contactor ,AC3 duty for 2.00 Nos 2782.55
time switch complete erected as per direction Cat III
[D] 4 pole 440V 40 Amp.
340 Supplying & erecting IP 55 grade following size 2.00 Nos 3595.60
section pillar fabricated from joint less M.S. Sheet with
angle iron legs made from jointless M.S. Angle with
cable clamps to be buried in ground to have
appropriate erection to work uniform until erected
with cement concrete foundation and 45 cms high
bricks work finishing with plaster etc. hinged double
door internally supported on both side, with internal
and outside looking arrangement with look and keys
in duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one
is welded and other with nut and bolt for erecting
bakelite sheet. Painting the Section Pillar inside and
out side with three tank powder coated paint. section
pillar roof should be without joint with water leakage
proof & tested as per IP 55 test & followed by IS
(B) 75 X 60 X 45 cm section pillar fabricated from
Gauge MS Sheet with angle iron legs 45 cm long made
from 35 X 35 X 5 mm thick MS angle.
341 Providing & Erecting full SS Body (SS 304) Split type 31.00 Nos 67226.61
water cooler having storage capacity 160 to
Ltr.(Tank SS 304) & Cooling capacity 150 ltr. Per hour
@ an ambient temp of 350 C.The outlet temp. of the
water should drop by 150C within a hour,The water
cooler should be comprising of hermetically sealed
Reciprocating compressor with R134A, fan motor,
Copper Condensing unit with company fabricated
Outdoor Unit water tank surrounded by evaporating
coil, thermostats, relay etc.complete with necessary
copper tube & Insulation, M.S Chanel Stand with
Painting for water tank & M.S. Powder Coated Stand
for Outdoor unit with Installation. With DPELCB and
Way DB Box with accessory Three core Cord for
connection.
Item Rate In
Description of Item Quantity Unit Amount
No figures
342 Supplying & erecting reverse osmosis (RO) water 4.00 Nos 335526.04
purification system with M.S. powder coated pedestal
frame, prefilter housing carbon filter suitable buster
DC pump, auto low & high pressure switches with
following size of LPH capacity & erected as directed
[H] 2000 LPH with 3 phase Raw water pump of
3400LPH @ 3.0 kg/cm2 (1No - Kirloskar /CRI /Lubi),
Dual media filter 18"x65" - 1 No., Micron catridge filter
20" x 4.0" - ( 2Nos), High pressure pump 3400LPH @
11kg/cm2 - (1No), Kirloskar/CRI/Lubi), RO
Membrane housing with RO membrane of 80*40 - (2
Nos), RO pressure tube 8" x 2E - (1No), 0 - 3500LPH
Rotameter - (2 Nos), Dosing pump 0 -6 LPH - (1 No).
with 100 Ltr Dosing tank - (1 No), Recovery Rate 50%.
343 Supplying, installing, testing & commissioning of 4.00 Nos 189956.76
SOLAR WATER heating system as per prevailing IS
code comprising of Solar flat locket collector, stainless
steel hot water storage isolated tank with S.S. heat
exchanger, absorber made of copper sheet & copper
tube of following capacity in liter / day (LPD) with "B"
size aluminium box collector with appropriate
capacity electrical backup arrangement (Excluding
inlet & outlet pipe lines) (E) Capacity of 1000 LPD
344 Supplying & erecting resin bonded flap rock wool / 650.00 Mtr 365.62
glass wool with conductivity valve 1.67 sq.mm per
watt & to with stand the temp. to 100 degree
centigrade C thickness 50mm with G I pipe of
following size dia "B" class as per IS:1239. The plastic
sheet to be used as covering of glass wool. Al. cladding
besides other materials like chicken mesh, 26 G Al.
Sheet shall be used for cladding the insulation pipe. [A]
for 20 mm dia pipe
345 Supplying & erecting resin bonded flap rock wool / 400.00 Mtr 767.60
glass wool with conductivity valve 1.67 sq.mm per
watt & to with stand the temp. to 100 degree
centigrade C thickness 50mm with G I pipe of
following size dia "B" class as per IS:1239. The plastic
sheet to be used as covering of glass wool. Al. cladding
besides other materials like chicken mesh, 26 G Al.
Sheet shall be used for cladding the insulation pipe. [E]
for 50 mm dia pipe
Item Rate In
Description of Item Quantity Unit Amount
No figures
346 Supplying & erecting 12mm composite pipe 220.00 Mtr 345.42
manufactured from polythene material with
destructed thermal expansion of 25 10-6 / degree
kelvin (low expansion Co-efficient), resistant to
freezing thermal conductivity 0.43 watt / (m degree
kelvin) UV resistant suitable for continuous operating
temperature of 95 degree centigrade & rated pressure
of 6.9 kg / sq.cms at 850 degree centigrade. The kitec
pipe shall have chemical composition prepared as per
ASTMF 1282-02 specifications (Pressure rating of
kg per sq.cms. & 11 KG per sq.cms at 60 degree) The
pipe shall be duly jointed by comprising crimp fitted
with internal as well as external end sealing
arrangement. [C] For 20 mm pipe
347 Providing and erecting Inverter based approved make 21.00 Nos 79620.32
split air-conditioning unit consisting of condensing
unit with variable speed fan motor, inverter type
hermetically sealed rotary compressor with
accessories etc. duly connected separately erected
evaporating unit and blower motor with its
accessories by means of extra supplied proper
insulated copper tubing,drain PVC pipes suitable for (
cost includes Eco Friendly green gas charging and 15A
plug top & Remote Control & MS Stand) with
necessary core cutting.(2)For ISEER Range
(KWH/KWH)(4.0 to 4.49) (C) for 1.7 to 2 ton capacity-
Premium Cat.
348 Supplying and erecting insulated pair of soft copper 210.00 Rmt 1158.47
tubing open or concealed including power and control
cable,necessary PVC drain pipes for Split/Cassette AC
machine up to 4 TR capacity
349 Providing & erecting L.T. Current Transformer with 45.00 Nos 274.72
bar primary 50/5 to 1000/5 ratio 15 VA burden
erected in existing CRCA box duly secured with
insulating materials connected to the meter
350 Supplying and erecting approved make suitable panel 45.00 Nos 43.43
indicator LED type lamp, lens cover, complete erected
with necessary connections.
351 Providing & erecting open well horizontal mono block 4.00 Nos 65116.72
pump set with cast iron body, complete for three
phase submersible motor having [J] For 25 HP 3 phase
open well horizontal mono block pump set suitable for
1850 LPM to 1075 LPM @ 36 to 60 MTR head suitable
for 65 /80 mm dia delivery pipeCat.II
Item Rate In
Description of Item Quantity Unit Amount
No figures
352 Supplying & erecting approved make motor control 2.00 Nos 24047.09
cubical panel [Star delta] made from 16G CRCA sheet
duly epoxy powder painted inside and outside with
hinged doors and locking with suitable size of ON -
OFF isolator (AC 3 / 23 duty) main fuses. Digital volt
and current meter (in a single unit) with micro
controller based control unit and current sensing
single phasing preventer electronic overload
protection, over voltage (Programmable) protection
and under voltage (Programmable) protection, prod
less dry run protection programming facility for
setting of all parameter like overload current, high
voltage limit, low voltage limit, dry run limit with
digital indication on seven segment LED display for
any fault like over load, high voltage, low voltage, dry
running single crimped, electronic star delta timer,
feather touch start / stop push buttons to be erected
on angle iron frame. Grouted on wall the contactors
will be of L& T, Siemens , BCH make only)(F) S/D up
353 Supplying and erecting approved make3 phase motor 1.00 Nos 55786.34
control panel (ATS) made from 16 G. CRCA sheet duly
painted with epoxy power paint inside and outside
with hinged doors and locking arrangement,
consisting, of suitable switch of AC 23 duty with HRC
fuses (Cat.III), starting and running contactors,
overload relay, Automatic water level controller,
Electronic timer with master timer CT operated
switch, phase indicating lamps, single phasing
preventer , water level guard, over load, start, run and
stop push buttons, air cooled auto transformer with
60%, 70%, 80% tapping, Panel to be erected on angle
iron frame grouted on wall as directed., contactors
relays, timer etc. shall be of L & T Siemens / Cutler
Hammer make. (E) Suitable for 50 H.P.
354 S.I.T.C. submersible pump set for bore of 200 mm. dia. 2.00 nos 111232.31
Or more having 3 phase motor capacity about 40-45
H.P discharge capacity having . Lifting and Lowering
taken extra. (B) ( 9 Stage) 1270 to 1180 L.P.M.
discharge at. the head 113 to 126 mtrs. suitable for
100 mm dia. delivery pipe Cat.II
355 Lowering of submersible motor pump set at the depth 1.00 Per Job 2996.67
of following ,complete with required. Nos. and size of
casing pipes erected by means of proper chain pulley
block & pipe wrenches after checking of threads of
each pipe with coupling to take the load of the pump
set and pipe assembly filled up with water (C)Above
Item Rate In
Description of Item Quantity Unit Amount
No figures
356 Lowering of submersible motor pump set at the depth 4.00 Per Job 1711.95
of following ,complete with required. Nos. and size of
casing pipes erected by means of proper chain pulley
block & pipe wrenches after checking of threads of
each pipe with coupling to take the load of the pump
set and pipe assembly filled up with water (D)For
Open well Horizontal submersible pump set for
sump well (iii)Above 15 HP
357 Providing and erecting ISI marked PVC insulated PVC 80.00 Mtr 172.71
Sheathed Flat flexible Submersible copper cable
approved make of following Size. (D) 3 Core x 6 Sq.
358 Providing and erecting ISI marked PVC insulated PVC 185.00 Mtr 647.41
Sheathed Flat flexible Submersible copper cable
approved make of following Size. (G)3 Core x 25 Sq.
359 Providing Water proof straight Joint in PVC insulated 8.00 Mtr 189.88
flat flexible copper cable by using insulating material,
water proofing material, & making the joint complete.
360 Providing Water proof straight Joint in PVC insulated 1.00 Mtr 278.76
flat flexible copper cable by using insulating material,
water proofing material, & making the joint complete.
361 Supplying & erecting UPVC heavy duty Flanges with 1.00 Nos 257.55
rubber packing and hardware materials for pipe
connections suitable for (D) 100 mm (4")
362 Supplying of following size of HEAVY UPVC column 110.00 Rmt 1130.19
pipe with coupler and wire lock[E] 100 mm dia
363 Supply of following size of TOP & BOTTOM accessories 1.00 Per set 3872.34
i.e. Adaptor set (CI) long, pump guard set, starter pipe
Rubber ring for submersible pump & UPVC column
pipe as directed by Engineer - in - charge with
necessary plumbing as desired. [G] 100 mm dia
364 Providing, erecting, testing & commissioning
approved make oil immersed ONAN cooled, double
wound, core type indoor / outdoor copper wound
11kV/ 433V step down transformer of following
capacities operating on 3 phase, 50 Hz 4 wire &
neutral earthed system continuously rated for a full
temperature rise in oil not exceeding 45 Deg.C.at
maximum ambient temp. of 50 Deg. C. complete with
necessary radiator first filling of new transformer oil &
standard fitting as below complying with IS 1180(
Part 1 ):2014 standards with energy efficiency level
Item Rate In
Description of Item Quantity Unit Amount
No figures
Off load tap changing range steps +2.5% to -5% on H.V
for variation should be provided. The H.V. shall be
connected Delta & Secondary with star connection.
The transformer should have cable-end boxes on H.T.
side suitable for up to 3 core 150 sq.mm. XLPE cable &
on L.T. side suitable for bus duct or cables as per
requirement complete with test certificates from
manufacturers
1. Oil conservator with filling Hole & Cap - One No.
2. Thermometer pocket with 6" dial type
thermometer switch alarm & trip contacts- Two
3. Silica-gel breather with charge- One No.
4. Plain oil level gauge - One No.
5. Drain / Sampling / Filter valve- One No.
6. Top Filter Valve - One No.
7. Explosion vent with Diaphragm - One No.
8. Rating & Diagram plate - One No.
9. Additional neutral bushing for earthing - One No.
10. Bi directional Roller - Four Nos.
11. Earthing terminals - Two Nos.
12. Lifting lugs - Two Nos.
13. Air release plug. - One No.
14. Double float buchholz relay with Alarm and trip
15. Control cable as required from Transformer to VCB
Panel is to be provided with necessary connection to
VCB relays for protection.
as per IS 1180 level-1
(c) 500 KVA 2.00 Nos 1428073.34
Max. allowable loses as per IS 1180 level-1 at the time
of tender Cat-III
365 Providing and erecting sandwitched type bus duct
having following specification : Sandwich type
busbar for use as Feeder Busbar for interconnection
between separate electrical equipment/ load centers,
and for use as Plug in busbar risers.
The busbar shall be suitable for operation in a 690V /
1000 V system with frequency of 50 Hz .System can be
either earthed or unearthed. Impulse voltage should
be 12 KV. Standards:
Item Rate In
Description of Item Quantity Unit Amount
No figures
The busbar shall be designed and manufactured in
accordance with the following international standards
for busbar trunking.
-IS 8623/ 1993 Part I & II : Particular requirements of
busbar trunking System
-IEC 61439 Part I & VI : Particular requirements of
busbar trunking System
-IEC- 60529 : Degree of protection TESTING
The busbars shall be type tested at a reputable
national / International test laboratory (ASTA or
CPRI) for short circuit withstand. The test shall be for
a minimum duration of one second.
• Degree of ingress protection (IP rating) shall also be
tested at any reputed independent laboratory. This
test shall be for IP 55 for Indoor and IP 65 for Outdoor
application.
• Short circuit and Degree of protection type test
reports will be submitted for vThe bsubars shall be of
high conductivity Copper of 99.9% pure ETP grade
and high conductivity Aluminium of 99.59% pure
63401 grade.
Where as earth conductor is required, it shall be
separate external earth conductor, of high
conductivity aluminium. Cross section of Earth
Conductor shall be as per IEC
It should be possible to provide a 200% Neutral where
specified.
Phase cross over box should have busbars crossing
over each other not cables.
The busbars shall be individually insulated with
layers of insulating film. Layers of POLYSTER material
class ‘F’, 155ºC.
The housing shall be made of 1.6 mm
electrogalvanised sheet steel, with an epoxy powder
coated paint finish of RAL 7032 grade. Alternatively
Aluminum casing of 2.5mm may also be provided. The
housings shall be profiled, to provide higher strength
and efficient heat dissipation. The width of the
housings shall be same for all ratings of busbars, in
order to provide interchangeability of tap off boxes.
The joints between sections shall be made so as to
provide flexibility during installation and expansion /
contraction of busbar during operation. The joints
shall be of the single bolt type. The joint construction
must have the following features.
Item Rate In
Description of Item Quantity Unit Amount
No figures
a) Thermal expansion of Busbars at joint of at least
mm per joint.
b) The joint insulation must be of one piece moulded
design and not have any cut edges which can absorb
c) Joint assembly shall be removable as separate sub-
assembly so that it can be inserted or removed
without disturbing the adjacent sections.
d) The joint system must be designed in a way that the
installer cannot insert the busduct length too far and
damage the bolt insulator.
e) The busbars ends shall not have any holes or slots at
the joints – the electrical continuity shall be through
pressure plates, achieving a high area of joint cross
section and expansion capability.
Tap of Units
a) Plug in boxes will be draw out type, contacts shall
be silver plated and spring loaded.
b) The front operating handle will be interlocked with
the plug-in boxes cover so that MCCB can be operated
only with suitable cover in close position.
c) The door shall be provided with the door knobs.
d) When the MCCB is in ‘ON’’ position, even with the
door knobs unlocked, the operator should not be able
to remove the box or open the tap off location cover.
e) During insertion, the earth conductor shall make
contact first before the phase conductors. This should
follow the sequence of first in last out concept.
f) When the box is open the live conductors shall be
safe guarded by a transparent insulator plate which
allows for visible inspection but does not allow
touching of the live conductors.
g) The tap off unit arrangement must achieve IP
without requiring any additional sealing at site.
h) The tap off boxes will be suitable for
accommodating MCCBs or other accessories, as
required. The tap off units should allow the flexibility
of accommodating different, reputed MCCB makes, to
be mutually agreed depending on the tender
requirements.
(B) Copper Bus (Maximum Current Density 160A/ 20.00 Mtr 23496.64
(b)800 Amp. capacity
Item Rate In
Description of Item Quantity Unit Amount
No figures
366 Providing, erecting, testing commissioning & getting
Plan Approval as well as NOC from Electrical Inspector
for extensible H.T panel comprising of one
630A/800A/1250A. H.T. VCB incoming & Two
outgoing 630/800/1250 A Drawout type VCB
confirming as per I.S. for use on 11 kV, 3 phase, 50 Hz.
unearthed A.C. supply system having breaking
rupturing capacity of 350 MVA or Above complete
with spring operated mechanism, mechanically &
automatic ON-OFF and spring mechanism charged,
discharged indicators, ON-OFF mechanical push
button, operation counter necessary auxiliary
switches, closing shunt trip, air insulated busbar
chamber having heat shrinkable PVC sleeves,
mechanical interlocks safety shutters, isolating plugs
and a VCB trolley with three vacuum interrupters with
epoxy support insulators and self aligning finger type
isolating contacts. The breaker shall be Manual cum
motorised mechanism & auto spring charge with TNC
switch closing with following accessories. The
Standared Companies Switchgear shall be Used and
Only Manufacutres as per IEC 62271-200/201 for
beneficial use.
1.flush mounting type digital multifunctional meter
with communication facility - Three sets.
2. Power Factor Meter One No
3. Double core current transformer cast resin type
having ratio 200 to 50/1 core for metering & second
core for protection having required class of accuracy. -
Three Sets
4. Instantaneous under voltage relay,Over Voltage
relay & Temperature rise Tripping Relay
5. Electrical closing coil & short trip coil operating on
110V. D.C.- Three Sets
6. Auxiliary relay for anti pumping device
7. Three phase Three limb Drawout type feeder
connected & output of 200 VA cast resin insulated
potential transformer having ratio 12000V./110V. and
200 VA Burdon with 0.5 accuracy. - One No.
8. Common Alarm bell operating on 110V A.C.- One
9. Digital KWH Meter - One No.
10. Cable boxes suitable up to 11 kV 3core 150 sq.mm
XLPE cable. - Three Nos.
11. 230V. A.C. to 110V. D.C. power pack for closing &
tripping circuit common.
12.Breaker ON-OFF, Auto trip and spring charged
indicators. - Three Sets.
13.Phase indicating & panel illumination lamps with
plug socket - Three Sets.
14.Numerical Communicable type non directional O/C
& E/F Relay with
a setting of 5-250% both in O/C & E/F. -Three Set
Item Rate In
Description of Item Quantity Unit Amount
No figures
complete with necessary interconnection with air 1.00 Nos 1328836.80
insulated high grade copper busbar {Breaker Testing
scope include Closing Time, Opening Time, VCB Hi-Pot
test at Site}{ Relay Testing Scope Include testing of all
protection by three phase testing kit at site }(VCB
Trolley is to be provided)
367 Design, Supplying, installing, testing of factory 2.00 Nos 580323.78
fabricated ready made Three phase APFC Panel
Cubical Panel fabrication should be type tested as per
IEC 61921, 61439:1&2 Capacitor Duty Contactor for
switching as per following Steps Incomer Switch of
MCCB type Icu=Ics=50KA at 400/440 Volts, with OC,
SC, internal earth fault protection Incomer Switch of
MCCB type Icu=Ics=50KA at 400/440 Volts, with OC,
SC, internal earth fault protection,Copper tinned
insulated Busbar,Cubical panel should be indoor type
with IP 43 and IK 10,Metalized polypropylene film
tye3-phase 550Volt Capacitor,De tuning Reactor for
each capacitor,Panel having Short Circuit and
Overload protection,Each step Capacitor having
suitable MCB with Sc, OL, internal earth fault
relay,Each stage having Stage Contactor (Capacitor
load rating),PF regulator master controller having
suitable steps with LCD display, Rs
Communication port, Indication LED Lamps for main
incomer and ON-OFF for each capacitor bank,MS
Chanel for Floor mounting, Cable entry as per site
situation,Cooling fans for panel (f)200KVAR
368 Providing and erecting ISI Marked 3core 150 Sq.mm 160.00 Mtr 1820.02
XLPE insulated 11 kV armoured cable Aluminium
conductor IS-7098 to be laid on wall with clamps or in
provided cable trench / pipe approved manner as
369 Providing and erecting cable end termination kit, heat 2.00 Nos 14611.67
shrinkable Push on type Densons/ Raychem/
Elastimold make suitable for 11 kV XLPE cable 3core
95 & 120 Sq.mm (A) Outdoor type
370 Supplying and erecting high tension cable end box 2.00 Nos 3853.15
outdoor type suitable. for 11 kV 150/185Sq.mm 3core
H.T. cable complete with gland bushing and jointing
371 Providing and fixing printed instruction chart both in 1.00 Nos 130.29
English and Gujarati and duly framed with front
glasses, for treatment of person suffering from Electric
shock with minimum 50" diagonally size.
372 Providing pair of rubber hand gloves suitable for 4.00 Nos 214.12
working on 11 kV/22 kV supply.
373 Supplying rubber matting of following thickness as per 20.00 Sq.Mtr 770.63
IS:15652/IEC 61111 (a)3mm
Item Rate In
Description of Item Quantity Unit Amount
No figures
374 Supplying rubber matting of following thickness as per 30.00 Sq.Mtr 3081.51
IS:15652/IEC 61111 (c)12mm
375 Supplying stand first AID box with antiseptic cream, 1.00 Nos 299.97
medicine for use on wounds due burn, crepe bandage,
gauge bandage, medicated ready to use bandage (Band-
aid) adhesive tape for medicinal user, Scissors, anti-
septic solution (Savlon or similar) etc. (All above
contents shall be of standard makes)
376 Supplying FIRE bucket round bottom of 9 litres 10.00 Nos 214.12
capacity made out of 24 gauge G.I. sheet with extra
handle at bottom duly painted white inside and Red
out side with FIRE mark, filled with dry-sand and kept
on existing stand provided or hung on wall hook.
377 Supplying and erecting floor mounting stand for 5.00 Nos 942.33
keeping four nos. of FIRE buckets comprising
mm in length, 900 mm height frame made out of
30mm X30 mm X 4 mm angle iron with cross supports
for legs, welded with 4 hooks and duly painted with
one coat of red lead and two coats of approved
enamelled silver paint.
378 Wall hook 22 to 25 cms. projection for keeping fire 5.00 Nos 60.60
buckets made out of 15 mm dia. M.S rod grouted in
wall to a depth of minimum 15 cms.
379 Supplying & erecting D.C.P. type fire extinguisher for 5.00 Nos 1712.96
following capacity cartridge type with gun metal cap
150 gram CO2 gas cartridge, powder and brackets
confirming to IS 2171 1985 and complete erected with
necessary clamps made from 50 x 6 mm M S Flat with
nuts and bolts grouted in wall complete. [A] For 5 Kg
380 Supplying & erecting carbon dioxide (CO2) fire 5.00 Nos 8671.86
extinguisher user of following capacity with necessary
clamps made from 50 x 6 mm M.S. Flat with nut &
bolts grouted in wall complete. [B] For 5.5 / 6.5 KG
381 Supplying & fixing Steel Chequered Plate having 12 8.00 Sq.Mtr 5780.23
mm thickness, duly painted with two coats of black
Japan colour. (Average Wt 200.3 kg / Sq.Mtr)
Item Rate In
Description of Item Quantity Unit Amount
No figures
382 Supply, Installation, Testing and Commissioning
(SITC) of Silent Type Diesel Generating (DG) Set(s) of
prime power rating (kVA) as specified, complete as a
packaged system, conforming to CPCB IV+ (or better)
emission norms, and complying with all applicable
statutory requirements, codes and standards including
(but not limited to) IS 4722:1968, IS 13364 (Part 2)
and BS 5514 (latest editions/amendments). The DG
set shall be suitable for 415 V ±10%, 50 Hz ±5%, 3-
phase, 4-wire operation at 0.8 lagging power factor,
1500 RPM, for tropical conditions, and shall be capable
of delivering 10% overload for one (1) hour after
twelve (12) hours of continuous operation (ISO 8528),
unless otherwise stated by the OEM. The scope shall
include complete accessories, interconnections,
foundations/anti-vibration arrangements, exhaust
system, acoustic enclosure, earthing (as required),
consumables for first commissioning, and all works
necessary to render the installation fully functional
and compliant, as directed by the Engineer-in-Charge
(EIC). Factory testing shall be carried out with fuel and
load bank at 0.8 power factor and the DG set shall be
offered for inspection prior to dispatch. The DG set
shall be provided with a durable QR code/label fixed
on the enclosure/control panel, linking to a document
repository containing (as a minimum) approved GA
drawings, wiring diagrams, foundation and
installation details, OEM catalogues, operating &
(C) Alternator:
Synchronous, brushless alternator of appropriate kVA
rating, 415 V, 3-phase, 50 Hz, 1500 RPM, 0.8 lagging
PF, continuous duty, dynamically balanced rotor, self-
cooled, self-excited and AVR regulated. Enclosure shall
be SPDP, minimum IP23. Insulation shall be Class H
with suitable tropicalization; temperature rise shall be
within limits of the applicable standard. The alternator
shall comply with IS 13364 (Part 2), IS 4722 and/or BS
2613 (latest), as applicable. Voltage regulation with
AVR shall be within ±1.0% (steady state) or OEM
standard whichever is better. The alternator shall be
capable of 10% overload for one (1) hour after twelve
(12) hours of continuous operation. Harmonic
distortion shall be suitable for non-linear loads;
alternator shall be equipped with appropriate AVR
features (e.g., soft start, UFRO) and shall be suitable for
motor starting duties typical to the installation.
Terminals shall be brought out to a terminal box with
adequate space for termination and shall include
earthing terminals. All routine/type test certificates
(as applicable) shall be submitted for acceptance.
(D) Base Frame & Foundation: Engine and alternator
shall be mounted on a suitably designed, fabricated MS
channel base frame with stiffeners, lifting
arrangement and coupling guard, duly painted/treated
for corrosion protection. The set shall be installed on
an adequately designed cement concrete
Item Rate In
Description of Item Quantity Unit Amount
No figures
(G) Starting System:
12 V / 24 V DC electric starting system (as per OEM
design) comprising starter motor(s), battery
charger/alternator charging arrangement, relays,
cabling and terminals, complete with maintenance-
free batteries of suitable Ah capacity to ensure
minimum three (3) consecutive cranking attempts.
System shall include battery isolator and indication of
charging healthy/failure. All battery interconnections
shall be with crimped lugs, insulated sleeves and
proper supports, complete in all respects.
(H) Acoustic and Weatherproof Enclosure: Acoustic
enclosure shall be factory-fabricated, weatherproof
and corrosion protected, suitable for outdoor
installation, with minimum IP65 protection (or better)
for the enclosure body. Enclosure design shall provide
adequate fresh air intake and hot air discharge for
engine radiator and alternator cooling such that the
internal temperature rise remains within OEM limits
at full load. Provision shall be made for safe
access/maintenance including lockable doors, viewing
window (where provided), emergency stop access,
and cable entry glands. Noise level of the complete DG
set with enclosure shall not exceed 75 dB(A) measured
at 1.0 m distance in free field conditions, in accordance
with applicable CPCB requirements. The enclosure
shall comply with CPCB IV+ (or better) requirements
(V) Continuous rating of 500 KVA ,BHP not less than 1.00 Nos 5072953.26
Item Rate In
Description of Item Quantity Unit Amount
No figures
383 AMF Panel: 1.00 Nos 443320.31
Free standing floor mounted IP 42 automatic
mains failure control panel including auto by-pass,
suitable for KVA as below for silent type DG set
complete with relays, timers, set of CTs for metering &
protection and energy analyser to indicate currents,
phase and line voltages, frequency, power factor,
KWH, Kilo Volt Ampere Reative Hour (KVARH), KVA
(Phase & Total), KW (MFM) & provision for
overload, short circuit, restricted earth fault, under
frequency, all complete and inter locking and
communication/ Ethernet /RS485/SNMP port open
protocol for BMS integration including suitable
software, the panel shall be of DG Set. as per
approved by Engineering in charge and including the
following:
1. Suitable numbers and appropriate capacity
ACB/ MCCB with electronic release for O/C & E/F and
shunt trip. (Icu=100%Ics) (Not below 25KA Breaking
Capacity at 415Volts), (Total Three Breakers)
3. Protection for under and over voltage phase
reversal (2 nos Over voltage relay, 2 Nos. reverse
power relay and 2 Nos. under voltage relay).
4. 3 Sets of current transformers 15 P 10 accuracy for
protection and 15 VA class-I for metering
5. Energy analyser unit to indicate current, Voltage( L-
N & L_L), kW, kVA (Phase & Total), Frequency, KWH,
SITC of Vertical Air Termination Solid aluminium with 2.00 Nos 9416.23
Base- 10 mm dia and 1000 mm long. Air Termination
Base tested for conditioning, Ageing Test & Lightning
impulse current withstand test: 100 kA of 10/350µs
waveform in an accredited Third party laboratory as
per 6.3 & 6.4 of IEC 62561-1 2017 protocol with MAST
34mm dia 3000 mm long- Cold Galvanized
385 SITC of 8 mm dia solid Aluminium Conductor for roof 360.00 Mtr. 299.97
top mesh grid and tested as per IEC 62561-
conducted in the Govt. accredited thirty party
laboratory to meet the requirement of IS/IEC
with Required Accessories - Aluminium Holding clamp
at every 1 mtr distance, Aluminium/SS cross splicer at
every crossing of Alu. conductor, Expansion piece with
connectors at every 20 mtr distance, Aluminium
straight Splicer to connect conductors. All Accessories
should be tested as per IEC 62561-1 2018 Cl. 6.3 for
conditioning & Ageing Test & 6.4 for Lightning
impulse current withstand test: 100 kA of 10/350µs
waveform(Ageing & Electrical test ) conducted in a
sequence manner & tested in the Govt. accredited
Third party laboratory to meet the requirements of
IS/IEC
Item Rate In
Description of Item Quantity Unit Amount
No figures
386 SITC of 10 mm MS Round Solid Conductor having 240.00 Mtr. 728.21
smooth surface Should be tested and use exclusively
for lightning protection (Vertical Riser/Down
Conductor which shall be concealed in Column OR
Flushed on) to meet the requirement of IS IEC
With Accessories - Earthing stud of dimension SS-
75mm OD plate with 10mm dia tail connector used in
structural steel ring earthing system to meet the
requirements of IS/IEC 62305. (For Interconnecting
the Column and the Terrace AL Conductor /
Strip/Flat), SS Cross Connector to connect Earth fixing
point to vertical raiser/Down conductor, SS Straight
Splicer at every 4 Mtr to connect MS conductor in
column, Bonding /Rebar Clamp at every 3 mtr suitable
for interconnecting round conductor with
reinforcement inside the concrete for structural
earthing system, SS connector -To connect external
conductor 8- 10 mm with earth fixing point. All
Accessories should be tested as per IEC 62561-1
Cl. 6.3 for conditioning & Ageing Test & 6.4 for
Lightning impulse current withstand test: 100 kA of
10/350µs waveform(Ageing & Electrical test )
387 SITC of Galvanized Steel Flat 25x6 mm thickness from 200.00 Mtr 154.53
earth electrode directly in ground as required. Zinc
coating: 500 g/m square (Approx:70 micron coating)
tested and used exclusively for lightning protection
earthing system and ring equipotential bonding.
388 SITC of 14.2 mm dia 3 mtr long Earth electrode of High 10.00 Nos 5992.33
tensile steel electrode with 250 micron copper
bonding & 1 bag of Carbon fill Based environment
friendly backfill tested as per IEC 62561-7 in NABL
accredited Laboratory and suitable stainless Steel
double sided clamp. Eco Friendly rust proof heavy
duty weather proof Polyethylene Earth Pit Chamber
with following dimensions :254 mm dia (top), 330 mm
dia (bottom) & 260 mm (height).
389 Supply,Installation,Testing and commissioning of Test 10.00 Nos 999.90
Clamp to disconnector the down conductor from the
earth termination network for regular checks of the
earth termination resistance value. ( including UPVC
box and all accessories.). It shall meet the
requirements of IEC 62561-2.
Item Rate In
Description of Item Quantity Unit Amount
No figures
390 SITC and fixing of ACE mortar seal for fire penetration 40.00 Sq.Mtr 23886.50
sealing system in floor opening for veritcal shafts &
wall opening FM approved class 4990.the mortar seal
shall have minimum 2 Hours fire resistant and
minimum thickness 100 mm.It should have been
tested at CBRI roorkee with following test in sequence
on same sample without any touchup or modification
during the test. With Fire rated Foam and PVC
IntumescentWrapping systems.. (1) Impact test
Kgs Hammer, (2) water absorbtion test for 24 Hours,
(3) accelerated ageing for 168 Hours, (4) vibration test
for 4 hours, (5) fire resistant test as per standards
ASTME 814,UL-1479, IS 12458/2019, BS 476 PART
(Certificates of all standards are required), (6) hose
stream test. Manufacturer original batch test
certificate for physical properties to be submitted.
391 Supplying, Erecting, Testing & Commissioning the
passenger / stretcher lift having following main
features: (A) GENERAL DESCRIPTION OF LIFTS.
[1] GEAR LESS LIFT DRIVE (MRL) comprising of High
Starting torque Lift 3 phase 440 V A. C. Permanent
Magnet Synchronous motor of proper rating with high
efficiency shall be used.[2] Micro processor based /
PLC, ACVVVF, vector control drive with encoder
feedback closed loop system shall be used for lift car
and door operation which shall be full collective
UP/DOWN hall stops, Main, Up/ Down Contactor with
overload and phase reversal relay and safety controls.
[3] Car with M S platform with bracings of adequate
size and to sustain the impact load cabin + passenger
with safety factor of fire for steel and side panels of
Stainless steel of sheet of grade 304 duty. Car ceiling
will be S.S. finishes with aesthetic appearance with
LED ceiling lights. Car flooring shall be of s/s
chaker plate design sugeested of engineer in charge. of
engineer in charge. Car doors shall be of stainless steel
grade 304, hairline finish with centre opening /
telescopic automatic doors. Car panel will also be S.S.
304 finished with emergency stop device, mechanical
door safety device, facility of auto/ attended mode. All
car panel buttons and all floor switches must be with
brail language as per lift act.
Item Rate In
Description of Item Quantity Unit Amount
No figures
[4] All landing doors must be fire rated for 2 hour shall
be fully automatic centre opening/ telescopic opening
made of hairline finish steel grade of 304 with key
holes and infrared curtains with Unlocking facility
from outside
[5] Appropriate battery operated emergency light in
the car along with alarm switch shall be provided.
Also, Emergency Light & Fan should start immediately
without any Time Delay as soon as power fails.
[6] Digital scrolling indicator system for up-down
arrow along with floor position indicator shall be
provided inside the car and at all floors.
[7] Full height infra red curtain with multiple cross /
crossing light beams shall be provided.
[8] Automatic Rescue Device (ARD) shall be provided
accordingly of passenger capacity with Manual Rescue
Operation ( Manual Cranking Facility).
[9] Audio visual indication in the lift car showing over
loading shall be provided such that doors kept open
till excess load is removed.
[10] Spring buffers/PU Buffers shall be provided.
[11] Car fan as per passenger capacity with automatic
sleep timer shall be provided.
[12] Voice annunciator with suitable music shall be
provided in lift car.
[13] Self diagnostics system for operational and safety
parameters shall be provided in control panel.
[14] Mechanical over speed governor with governor
calibration as per actual site parameters and
submission of calibration certificate submission, door
key holes in the floor doors, fireman switch shall be
[15] Lift machine hoisting arrangement in the lift
machine room and monkey ladder for lift pit should be
provided by the lift agency, along with the other steel
structure works, foundations for the machine etc…
[16] In the hoist way fascia plate shall be provided
without any extra cost, where ever required as / if
directed by engineer in charge.
Item Rate In
Description of Item Quantity Unit Amount
No figures
[17] Permanent wiring with necessary safety devices
like RCCB in all circuit, Over Voltage Under Voltage
protection and THD eliminator in circuit for lift
machine room and lift well with proper numbers of
light points, with fixtures, exhaust fan and plug points
shall be provided by the agency. Only 3 phase Power
Supply shall be made available by department in lift
machine room. Necessary Earthing as per Lift
Act/Rules shall be arranged by Lift Agency.
[18] Any civil/ electrical works for additional and
alteration in lift shaft and machine room related to
erection of lift shall be made by lift agency without any
extra cost. (granite/marble fixing around all landing
door openings are not in lift agency’s scope.)
[19] Agency has to provide all working drawings and
documents and liaison services for obtaining all
necessary permission from lift inspector and other
authorities. [20] acrylic transparent
licence/display A4 size holder in lift car
[20A] As per statutory requirement of Govt. Of Gujarat
lift & escalator act 2000, lift agency has to provide
1. Car top safety barricade
2. Push & talk communication system.
3. Fireman's switch operation at Ground Floor.
4.carrying out third party lift inspection during/after
lift erection and provide report by third party
authorized by concern licensing authority 5.agency
has to provide third party insurance upto completion
of free maintenance period and submit the document
for the same.
[21] Car Panel Operating Buttons with floor position
indicator/buttons must be of Auto Glow type clearly
visible when view from inside cabin.
[22] For Physically Handicapped person Full Length
Handrails of hairline finish steel grade of 304 should
be provided at appropriate height on the Rear & Side
Wall Panels in Lift Car. [23] With Necessary KVA
rating voltage controlled Stabilizer suitable for your
controller, drive and all equipments of lift.
[24] Necessary rating of DP Elcb and FP Elcb required
for lift is in scope of work which rating is sugested by
CEICED Department (electrical Inspector)
(B) SPECIAL FEATURES DESCRIPTION OF LIFTS for
PREMIUM category
Item Rate In
Description of Item Quantity Unit Amount
No figures
1. Advanced control system dual 64 bit embedded
microprocessor with CANBUS Serial Communication
mode including Regenerative power efficient
operation,on site programming facility, Anti nuisance,
Pte-opening, BMS/RMS with necessary online real
time monitoring system having necessary connectivity
for remote monitoring & other suitable supporting
hardware & software devices to fulfil the purpose.
2. Floor Indication LCD Display with call registration &
brail mark with arrival gong and hall lantern & TFT
Screen in the car with MP3 Voice Announcer.
3. CAR Panel should be Scratch resistive SS Moonrock
finish / Hair Line / Honeycomb for car and all Doors,
All landing doors must have fire rating up to 2 hours
and car door must have multi-level crisscross beam
door protection.
4. To & fro communication system & wiring (i.e. car
control room & guard room ) and Each elevator are
equipped with remote monitoring system.agency has
to provide mobile app and user id and password for
monitoring
15/16 Passengers, Ground plus 7 upper floors with 2.00 Nos 2697456.49
Rated Speed of 1.5 /1.75 m/sec., (C) With General
PLUS ADDITIONAL SPECIAL FEATURES attached
herewith. Prem. Cat.
392 Supply of Fibreglass Step Trestle (A Type) Ladder - 6 1.00 Nos 16312.51
FT having following specifications :
It should have heavy gauge steel hinges suitable for
industrial application ,inside Spreader Braces,
Aluminium Feet with thick rubber tread,
nonconductive Full channel Fiberglass,two pairs of
gusset support at the bottom step and All gussets are
heavy duty steel. It should have steps on both the sides
for climbing. Capacity : 300 lbs." Step Width : 3”
Bottom Width:23” Approx.
Spread : 52”Approx.Wt.:13 Kg Approx. Cube : 6.53’
393 Supply of Fibreglass Platform Step (A Type) Ladder - 1.00 Nos 27978.01
10 FT having following specifications :
It should have large fully serrated
platform 15” wide 20” deep which locks ladder
Aluminium feet with thick rubber tread, top rail guard
to serve as a railing, two pairs of gusset support at the
bottom step and All gussets are heavy duty steel.
Capacity : 300 lbs. Step Width : 4’ Approx. spread
: 75” Width : 32” Approx. Wt. : 29 Kg Approx.
Total B
Total A+B
Item Rate In
Description of Item Quantity Unit Amount
No figures
I/We am/are willing to carry out the work at………………….% above/below percent(Should be written in figures and
words) of the estimated rate mentioned above. Amount of my /our
Tender works out as under.
Estimated amount put to tender Estimated amount put to tender
Deduct………% below Add………% Above
In words In words
The Contractor shall exhibit a board with detailed specification and details of work as directed by the
1 Engineer-In-Charge for which no extra payment shall be made.
2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.
3 Income tax TDS will be deducted at a source while making payments of bills
In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-
10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where
4 there is a change as per actual mix design the cost of difference of cement consumption have been deducted
from the rate of original item at the rate of input rate mentioned in all the tender.
5 GST will be paid Extra as per Govt. amendment
Deputy Executive Engineer Executive Engineer
Capital Project Sub Division:11 Capital Project Division No
Gandhinagar Gandhinagar
Executive Engineer
C.P. Elect. Division
R&B Deptt., Ahmedabad.
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
RAW_HTML
GRs (2 side) Final compressed-106-146.pdf
GRs (2 side) Final compressed-71-105.pdf
GRs (2 side) Final compressed-36-70.pdf
GRs (2 side) Final compressed-1-35.pdf
Specification Booklet-9.pdf
Specification Booklet-1.pdf
Specification Booklet-2.pdf
Specification Booklet-3.pdf
Specification Booklet-4.pdf
Specification Booklet-5.pdf
Specification Booklet-6.pdf
Specification Booklet-7.pdf
Specification Booklet-8.pdf
Draft Letter Tender Validity.pdf
7.0 SBD Samras Girls Hostal Gandhinagar (2 side).pdf
8.0 BOQ Samras Girls Hostal Gandhinagar (1 side).pdf
10.1 Item Wise Specification Samras Girls.pdf
2.0 Notice InvitingTender.pdf
0 Pre Qualification Bid Samras Girls Hostal Gandhinagar (1 side).pdf
Drawing 1 to 4.pdf
Drawing 5 to 8.pdf
Drawing 9 to 12.pdf
Drawing 13 to 16.pdf
10.0 Detail-Specification (2 side).pdf
9.0 General_Condition (2 side).pdf
0.1 PQ GR (2 side).pdf
10.2 Building-Specification Booklet (2 side).pdf
Special conditions of contract R1.pdf
8 Make list improved 05-09-2026 (1).pdf
5 Maintenance condition Policy -final.pdf
0.12 Special_condition (1 side).pdf
0.11 SPECIAL_CONDITION_grade_change _21side_.pdf
CV Frmt.pdf
004 Special_Condition_Tower_Crane_Deployment (1).pdf
003 SC for Site cleaning R1 (1) (1).pdf
002 RnB_Gujarat_SCC_Safety_Health_First_Aid_Brief_Revised (1).pdf
001 Certificate_Acknowledgement_Acceptance _1_.pdf
TECHNICAL SPECIFICATION (2).pdf
Nomination for Electrical Contractor (1).pdf
MOU Electrical Work (1).pdf
Lift Condition (1).pdf
Certificate of material-Samras- Sector -15 _1_.pdf
Annexure lift 1.pdf
Samras Girls Hostel Sector 15.pdf
15 year lift amc GR.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .