Road Tarring from Mahalakshmi kshethram to Thulakkilampadu Thulakkilampadu to Pulliyilnada in Thavaravila ward (95)

Amount

Tarring

4.9 : Wet Mix Macadam <br> Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406. <br> By Mechanical Means with 1 km lead

5.1.1a : Prime Coat :- Low porosity <br> Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

5.2.2a : Tack Coat <br>Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

5.9.1.2a : 20mm thick Open-Graded Premix Carpet using Bituminous (penetration grade/modified bitumen) Binder - Bitumen S-65 <br> Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. <br> Case - I By Manual Means <br> (II) Bitumen (S-65)

5.12.B.1.2a : Seal Coat - Mechanical Means - Type A - Bitumen S-65 <br> Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 <br> B. By Mechanical Means :- Case - I : Type A <br> (II) Bitumen (S-65)

od627870/2020_2021 : Plain cement concrete pavement ,thickness as per design,over a prepared sub base,with 43 grade cement or any other type as per clause 1501.2.2 M 30 (grade),coarse and fine aggregates conforming to IS 383,maximum size of coarse aggregate not exceeding 25 mm,mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design,laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges,steel plates including&lt;br&gt;levelling the formwork as per drawing),spreading the concrete with showels,rakes,compacted using needle vibrator and finished in continuous operation including provision of contraction and expansion ,construction joints,curing of concrete slabs for 14 days, finishing to lines and grade as per drawing and Technical Specifications clause 1501 (Modified 6.4 MORD with Formwork)&lt;br&gt;&lt;br&gt;Code

od627901/2020_2021 : Construction of Embankment with Material Obtained from Borrow Pits&lt;br&gt;&lt;br&gt;Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5&lt;br&gt;

Filling

51.2.3 : Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

50.2.26.1 : Filling with contractor own earth (excluding rock) in open areas in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge.

Side wall

11.1.1.1 : Excavation for StructuresEarthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.I.Ordinary soil(i)Upto 3 m depth

od627568/2020_2021 : Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 &amp; 1203.I. Coursed rubble masonry (1st sort)

od627569/2020_2021 : Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 &amp; 1203.&lt;br&gt;III. Random Rubble Masonry&lt;br&gt;(iii)In cement lime mortar (1:0.5:4.5)

11.4.3.2 : Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203III. P.C.C. grade M 20(ii) Nominal mix 1:2:4 (Hand mixed)

CHANDRAN H

Bidder Name

ANILKUMAR N

CHANDRAN H