Erumala Reconducting LT 3ph OH line with ABC (work code CW-4653-202526-27) under Electrical Section, Chullimanoor

Fitting one LT 2 line cross arm on HT or LT existing poles including fitting insulators and binding the same with LT Line

Providing one Earth using GI earth pipe of size 38.1mm dia, 2.5m length including digging separate pit (0.45x0.45x2.5m) at a minimum distance of 1.5m away from the pole/structure and maintaining standard distance between different earth pipes in ordinary soil & backfilling.

Installation of Pre-insulated lugs for 16sqmm

Fitting of one No. pole top service connection box of standard size (up to 4 way) using ss strap/B&N of suitable size in to the PSC/A poles at the standard height excluding giving connections

Installation of Pre-insulated lugs for 50sqmm

Installation of Pre-insulated lugs for 70sqmm

Additional rate for refitting/redoing one Shackle Set, including reshacling one span, while renewing any type of LT pole

Labour charges for loading HT PSC pole from the stacking place and unloading the same at work site (transportation by any vehicle)

Labour charges for loading LT PSC pole from the stacking place and unloading the same at work site (transportation by any vehicle)

Transporting poles by hired vehicle to a distance upto 5km and carrying upto 4 numbers of poles excluding loading& unloading charges

Fitting and erecting one HT PSC Single Pole in position, including fitting cross arm, digging and back filling pit in ordinary soil (as per standards), drawing sufficient length of GI earthing leads from F clamp through V cross arm to the ground for earthing (excluding provision of earthing)

Erecting one LT PSC Pole in position including digging & back filling pit in ordinary soil

Dismantling (without damage) one km LT three phase 4 wire OH line conductor by dismantling cross arms, insulators and stacking the conductors in rolls properly

Dismantling (without damage) one km LT additional conductor line by dismantling cross arms, insulators and stacking the conductors in rolls properly

Stringing of 1.1 kV Aerial bunched cable of size 3 x 70 + 1 x 16+1x 50 sqmm with bare/insulated Messenger through existing poles

Erection of Anchor clamp / dead end clamp for LT ABC of any size

Erection of suspension clamp for LT ABC of any size

Installation of Insulation piercing connector for main to service line main :16-95 sqmm, Tap 16-95 sqmm

Installing One No. Insulation piercing connector of size Main :16 to 95 ,Tap:1.5 to 16 Sq.mm

Providing one Coil Earth using No.8 GI-earth wire (50mm dia, 115 turns) including digging separate pit (0.45x0.45x1.5m) at standard distance away from the pole/structure in ordinary soil & backfilling

Fitting one LT 4 line cross arm on HT or LT existing poles including fitting insulators and binding the same with LT Line

Disconnecting and lowering down the single phase WP service connection with guy wire from the OH line and reconnecting the same after completing the line work

Disconnecting and lowering down the three phase WP service connection with guy wire from the OH line and reconnecting the same after completing the line work

Dismantling (without damage) one LT PSC/RCC pole after disconnecting stays, strut etc. attached thereon and stacking the same

Dismantling one ordinary street light/CFL/LED fitting from existing pole and refitting the same on newly erected pole including disconnecting and reconnecting wires

Renewal of existing damaged/broken old LT stay in existing stay rod

Fitting one No. Section fuse on LT line with dropping cables, crimping sockets, connecting with bolt & nut etc

Straightening one slanted 11kV pole after unbinding the line and binding the line after work

Straightening one slanted LT pole after unbinding the line and binding the line after work

Providing End Caps

Transporting LT ABC by hired vehicle to a distance up to 5 km and carring up to 2 drum including loading and un loading using crane

Transferring LT single phase 2/3 wire OH line to newly erected HT/LT pole including dismantling existing cross arm and insulators, refitting the same on the new pole, binding etc. complete

Transferring LT three phase 4/5 wire OH line to newly erected HT/LT pole including dismantling existing cross arm and insulators, refitting the same on the new pole, binding etc. complete

Renewal of existing damaged/old LT PSC/RCC (three phase line) pole with new PSC pole in place including excavation of pole pit, erection of new pole, backfilling pit and refitting of all items except street light fitting etc. and conveyance of all materials except pole

Dismantling one damaged LT PSC/RCC pole after disconnecting stays, strut etc. attached thereon and stacking the same

Renewal of existing damaged/old 11kV PSC/RCC Pole with new PSC pole in place including excavation, erection of new pole, backfilling pit and refitting of all items etc. and conveyance of all materials except pole

Renewal of existing damaged/old 11kV PSC/RCC Pole with new A type pole in place including excavation, erection of new pole, backfilling pit and refitting of all items etc. and conveyance of all materials except pole

Providing concrete muffing of size 0.45x0. 45x1.5m (0.5m above GL and 1m below GL). Excavation 0.45x0.45x1m, concrete (1:3:6, 20mm) 0.45x0.45x1.5m, Plastering (1:3) 12mm 0.45x0.45mx5sides

Fitting one Additional 75x40mm, 1.8m Channel cross arm in existing single pole including conveyance of materials

Fitting one Additional 2.4m/3m Channel cross arm (100x50x6mm), in existing 11kV DP including conveyance of materials

Dismantling one section fuse from structure and bringing back to section store

Additional rate for refitting/redoing one Disc set while renewing any type of 11kV cut pole

Fitting one Additional V cross arm in existing single pole including conveyance of materials

Dismantling (without damage) one Channel cross arm from existing DP structure and bringing back to section store

Insertion of one HT PSC pole in existing OH line including digging & backfilling pit in ordinary soil, fitting cross arm, insulators, binding etc., drawing sufficient length of GI earth leads to the ground for earthing (excluding provision of earthing)

Fitting and providing one HT Fly stay for 11kV pole using HT PSC pole including digging and back filling pits in ordinary soil, drawing sufficient length of GI earth leads to the ground for earthing (excluding provision of earthing)

Renewal of existing damaged/old LT TW/RSJ/Rail (three phase line) pole with new PSC pole in place including excavation of pole pit, erection of new pole, backfilling pit and refitting of all items except street light fitting etc. and conveyance of all materials except pole

Labour charges for loading HT A type pole from the stacking place and unloading the same at work site (transportation by any vehicle)

Providing Stay for LT poles including digging & back filling pit in ordinary soil

Fitting and providing one HT Stay for 11kV pole, including digging and back filling pit in ordinary soil

Fitting one Additional 2.4m Channel cross arm in existing single pole including conveyance of materials