REPAIR TO MISC WOODEN FURNITURE ITEMS AND CHARPOY GI PIPE PLY TOP INCL POLISHING AND REPAIR/PAINTING OF MISC STEEL FURNITURE ITEMS FOR CHARDUAR AREA UNDER GE (N) TEZPUR

Amount

Note 1: (Applicable for all parts/items) : The bidders/contractors are advised to read tender document, all drawings & all corrigendum/amendments and general condition of contracts before entry/quoting the rates. Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading of incorrect/ pre-revised BOQ shall be treated as non bonafide and rejected. Fixed credit has been given in technical documents which shall be taken into account during acceptance of bid/tender.

Chair Dining :- M & L for removing of the following UNSV parts from chair dining and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size all as specified and directed. Drg No. FD-279

S&F Front leg

S&F Rear leg

S&F Front rail

S&F Rear rail

S&F Side rail

S&F Stiffener 'H' type

S&F Back Rest

Chair Easy :- M & L for removing of the following UNSV parts from chair Easy and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size all as specified and directed. Drg No. FD-229

S&F Front leg

S&F Rear leg

S&F Arm Rest

S&F Front rail of seat frame

S&F Rear rail of seat Frame

S&F Side rail of seat frame

S&F Side rail of back frame

Lower back frame

Upper Rail of back frame

Chair writing : M & L for removing of the following UNSV parts from chair writing and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size all as specified and directed. Drg No. FD-20, 202, 250 & 280

S&F Front leg

S&F Rear leg

S&F Front rail

S&F Rear rail

S&F Side rail

S&F Stiffener 'H' type

S&F Back Rest

S&F Arm Rest

Caning of Chair all type : M& L for removing UNSV cane plastic from chair easy, chair dinning, chair writing etc and cleaning the surfaces and recaning the chair with 2mm wide 0.4 thick new plastic cane in godrej pattern and perimeter woven with 3 mm wide half round cane of approved make. Rest all as directed. Drg No. FD-279, 229, 202,250 & 280

Bed Plywood Top : M & L for removing UNSV parts from Bed Ply top and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size all as specified and directed. Drg No. FD-246

S&F of Ply wood 12 mm thick commercial BWR grade of approved make with appropriate screw.

S&F of ply wood 4 mm thick one side teak face on both side of head board with plywood of approved make beaded with 4 mm thick teak wood beading.

All as per item No 5.02 above but foot board.

S&F of leg of head board made out of Ist class hard wood.

All as per item No 5.04 above but for leg of foot board

All as per item No 5.04 above but for long rail

All as per item No 5.04 above but for short rail

All as per item No 5.04 above but for stiffner

Sofa Set 5 Seater/4 Seater/single seater : - M & L for removing of the following UNSV parts from Sofa set 5 Seater/4 seater/single seater and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size all as specified and directed. Drg No. FD-281,373

Arms rest

Batten

Front Long Rail of 3 Seater Seat frame

Rear Long Rail of 3 Seater Seat frame

Upper Long Rail of 3 seater back frame

Lower long Rail of 3 seater back frame

Replacing of existing old cushion foam size 22”x21”x4” from seat and back of Sofa set and supply and fixing of new cushion foam 22”x21”x4” (U Foam) 32 density of sleep well OR Godrej PURITO or ,kurlon & covered with cloth tapestry as per sample approved by GE (Cost of tapestry cloth not less than Rs 250/- per meters). The tapestry cushion cover shall have zip arrangement to accomodate the cushion all as specified and directed

Table Centre :M & L for removing of the following UNSV parts from Table centre and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size as per drg all as specified and directed. Drg No. FD-29,235 & 274,375

Short rail.

Long rail.

Stiffener.

M & L for removing of UNSV top from table centre and S & F top made out of 18mm thick prelaminated particle board exterior grade of approved make and beaded with 4 mm thick teak wood beading duly polished all round the top complete all as shown on drg and directed.

Table Peg : M & L for removing of the following UNSV parts from peg table and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size as per drg all as specified and directed. Drg No. FD-46,236 & 277

Side rail.

Stiffener.

M & L for removing UNSV Top of peg table and S & F Top made out of 18mm thick prelaminated particle board exterior grade approved make and beaded with 4 mm thick teak wood beading duly polished all round the top.

Teapoy - M & L for removing of the following UNSV parts from teapoy wooden and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size as per drg all as specified and directed. Drg No. FD-34(m), 278

Long rail.

Short rail.

Stiffner 'H' Type

M & L for removing of U/S top from teapoy and S&F top made of 18mm thick prelaminated particle board exterior grade approved make and beaded with 4 mm thick teak wood beading duly polished all round the top.

Table Writing :M&L for removing of the following UNSV parts from table writing and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size as per drg all as specified and directed. Drg No. FD-249 & 275

Stiffener

Long Rail

Short Rail

M&L for removing U/S Top from Table writing and S&F of top made out of 18mm thick prelaminated particle board exterior grade approved make and beaded with 4 mm thick teak wood beading duly polished all round the top.

M&L for removing U/S Door of cup boards from Table writing and S&F of new door made out of 18mm thick prelaminated particle board exterior grade approved make and beaded with 4 mm thick teak wood beading and fixed with piano hinges.

All as per item No 10.06 above but for side.

All as per item No 10.06 above but for drawer.

M&L for removing U/S ply wood from back side of Table writing and S&F plywood 6mm thick commercial, BWR grade of approved make with appropriate screws.

M&L for removing U/S Knob from table writing and S&F new knob best quality all as specified and directed.

Table Dining 6 Pers- : M & L for removing the following UNSV parts from table dining 6 pers and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size as per drg all as specified and directed. Drg No. FD-46,236,273 & 277

Long rail.

Short rail.

M & L for removing UNSV corner and S & F new corner made out of 100x100x25mm 4 Nos each made to shape and fixed with appropriate screws.

M & L for removing of UNSV top from Table ding 6 pers and S&F top made out of 18mm thick prelaminated particle board exterior grade approved make and beaded with 4 mm thick teak wood beading duly polished all round the top.

Table Dining 8 Pers : M&L for removing of the following UNSV parts from table dining 8 pers and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size as per drg all as specified and directed. Drg No. FD-46,236,273 & 277

Long rail.

Short rail.

S & F corner made out of 100x100x25mm 4 Nos each made to shape and fixed with appropriate screws.

M & L for removing of U/S top from Table dining 8 Pers and S&F top made out of 18mm thick prelaminated particle board exterior grade approved make and beaded with 4 mm thick teak wood beading duly polished all round the top.

HAT STAND WITH MIRROR -FD-206 & 233

Taking out unserviceable mirror of hat stand and S&F of new mirror, 4mm thick of Make : Atul/Modiguard and fixed complete all as pecified on drawing and directed.

S&F in replacement of new aluminium cap hooks as per existing shape & sixe complete all as specified on drawing and directed.

Taking out unserviceable back portion plywood of hat stand and S&F of new 12mm thick plywood, BWR grade, commercial type complete all as specified on drawing and directed

Removing of old unsv plywood front side of hat stand and and S&F new plywood of hat stand one side teak face 4 mm thick with 4 mm thick teak wood beading all round

Table Dressing Ladies - : Drg No. FD-32,251 & 378

M & L for removing UNSV top from table dressing ladies and S & F new top made of 18mm thick pre laminated particle board exterior grade of approved make and all as specified and directed.

All as per item No 14.01 above but for side.

All as per item No 14.01 above but for drawer.

M & L for removing UNSV mirror from Table dressing ladies and S & F new 5 mm thick mirror of approved make and remove back ply and fix new ply 6mm thick commercial type BWR with appropriate screw all as specified and directed .

M & L for removing UNSV knob and S&F new knob best quality all as specified and directed.

M&L for removing UNSV leg from table dressing ladies and S&F new legs of made out of Ist class hard wood teak all as specified and directed.

(g) M&L for removing UNSV Glass sliding shutter with aluminium channel from table dressing ladies and S&F new Glass shutter made out of 5mm thick glass pan with aluminium channel 20 mm width with appropriate screw all as specified and directed.

Table Dressing Gents : Drg No. FD-31 & 230

M & L for removing UNSV mirror of Table dressing gents and S & F of new 5 mm thick mirror of approved make with new teak wood frame and fix plywood 6mm commercial type BWR on back with appropriate screw all as specified.

M & L for removing UNSV top from table dressing gents and S & F new top made of 18mm thick veneered teak face pre laminate particle board exterior grade all as specified.

All as per item No 15.02 above but drawer.

All as per item No 15.02 above but side.

M & L for removing UNSV knob from Table Dressing gents and S&F new knob best quality all as specified.

M & L for removing UNSV ply wood from box backside of Table Dressing gents and S&F new ply wood 6 mm thick commercial BWR grade with appropriate screw all as specified.

Charpoy GI pipe plywood top : - Drg No. FD-220(M)

M & L for Removing UNSV three Nos MS flats Iron size 25x5x850mm long for each charpoy to be fixed by welding in between long rail in equal distance and two holes in each flate iron and apply black synthetic enamel paint over a coat of primer rest all as directed.

M & L for Removing UNSV flat iron size 25x5x220mm long four number in each charpoy to be fixed by welding in each corner in between long rail and short rail and one hole on each flate iron of charpoy with long rail & short rail and apply black synthetic enamel paint over a coat of primer rest all as directed.

S&F ply wood 12mm commercial BWR grade of approved make on top of charpoy GI pipe with appropriate nut and bolt headless 6mm with washer complete all as specified and directed.

M&L for removing of UNSV long rail from charpoy GI Pipe 32mm and S&F long rail made of GI tubing 32mm dia medium grade heavy duty of approved make duly threaded on both ends all as specified and directed.

M&L for cutting of dismantled old UNSV long rail from charpoy GI Pipe 32mm dia modifying into short rail by threading both ends and fixing the same to charpoy GI pipe all as specified and as directed.

M&L for cutting of dismantled old UNSV short rail from charpoy GI Pipe 32mm dia and modifying into legs and threading of end and M&L for welding the clamps for FMN set and fixing the same to charpoy GI pipe all as specified and as directed.

M & L for removing of UNSV elbow from charpoy GI pipe and S&F new GI three way elbow 32mm dia med grade of approved make and all as specified and directed.

M & L for removing of old UNSV check nut from charpoy GI pipe and S&F new GI check nut 10mm thick complete all as specified and directed

Polishing : M&L for removing old polish from the surfaces by scrubbing with emery paper, cleaning all dust, filling bore holes with pasty filter prepared by mixing plaster of paris with water to a creamy consistence and adding raw in quantity to obtain the desired colour to the base and to allow the surface to be dried up and set aside for 24 hrs for the surfaces to harden, rub the surface with sand paper it is thoroughly smooth and dried to receive a coat of acrylic wood finish polish of approved make complete all as specified and as directed for the following:-

Chair dining (Drg No. FD- 279)

Chair Easy (Drg No. FD- 229)

Chair writing/CBA (Drg No. FD-250, 280)

Bed Ply wood top (Drg No. FD-245, 246, 247)

Table center(Drg No. FD-235, 274)

Table peg (Drg No. FD-46,236 & 277)

Table writing (Drg No. FD- 275 , DB-3902)

Teapoy (W) (Drg No. FD-232 & 284)

Sofa Set 5 Seater (Drg No. FD-281, 373)

Sofa Set 4seater (Drg No. FD-281, 373)

Sofa Set single seater (Drg No. FD-281, 373)

Table office offrs/ clk wooden

Table Dining 6 Pers (Drg No. FD-236, 277)

Table Dining 8 Pers (Drg No. FD-236 , 277)

Almirah large steel with shelves :. Drg No. FD-351,104(m),1031,1033

M & L for removing UNSV shelves from almirah large steel and S&F of new shelves made of 1.6 mm thick MS sheet all as specified and directed

All as per item No 18.01 above but lock cover.

All as per item No 18.01 above but leg.

M& L for spot welding to almirah large steel complete all as specified and directed.

M & L for removing UNSV 3 way locking device from almirah large steel and S&F new 3 way locking device all as specified and directed.

M & L for removing UNSV lock from almirah large steel and S& F new lock 6 lever of approved make rest all as specified and directed.

M & L for removing UNSV handle from steel almirah and S&F of new handle of chromium plated all as specified and directed.

M & L for removing UNSV door hinges from steel almirah and S&F of new door hinges 75/80 mm duly welded all as specified and directed.

Almirah Med steel with shelves : - Drg No. FD-243,114(M),1032,1034

M & L for removing unserviceable shelves from almirah med steel and S&F of new shelves made of 1.6 mm thick MS sheet all as specified and directed.

All as per item No 19.01 above but lock cover.

All as per item No 19.01 above but leg.

M& L for spot welding to almirah Med steel complete all as specified and directed.

M & L for removing UNSV 3 way locking device from almirah med steel and S&F new 3 way locking device all as specified and directed.

M & L for removing UNSV lock from almirah large med and S& F new lock 6 lever of approved make rest all as specified and directed.

M & L for removing UNSV handle from almirah med steel and S&F of new handle of chromium plated mild steel all as specified and directed.

M & L for removing UNSV door hinges from almirah med steel and S&F of new door hinges 75/80 mm duly welded all as specified and directed.

Chair Varandah : - Drg No. FD-256

M& L for spot welding to chair varandah complete all as directed.

M & L for removing UNSV cane plastic from chair varandah and smooth the surface and apply two coats of white synthetic enamel paint complete all as specified and directed.

M&L for Re-canning of Chair Varandah in mat pattern with 4 mm wide 0.5 mm thick half round plastic cane of approved make all as specified and directed.

M & L for removing UNSV hard PVC shoes from chair verandah and S&F new PVC shoes four Nos each chair complete all as specified and directed.

Table Office Officer steel :- Drg No. FD-1003

M & L for removing UNSV top from table office officers steel and S&F of new top made out of Pre laminated particle board 18/19mm thick exterior grade of approved make with 4mm thick teak wood beading around the top complete all as specified and directed.

M & L for removing UNSV drawer from table office officers steel and S&F new drawer made of 1mm thick PBI sheet and all as specified and as directed.

M&L for removing UNSV leg and S & F New leg made of MS square pipe 25mm and 1.6mm thick 04 Nos in each table rest all as specified and directed.

M& L for spot welding to Table office offrs steel all as directed.

M & L for removing UNSV stiffener and S & F new stiffener made out of MS square pipe 25mm and 1.6mm thick of Qty 03 Nos in each table rest all as per drg and as directed.

Removing UNSV hard PVC shoes from Table office offrs and S&F new PVC shoes four Nos each table and all as specified and directed.

Table office Clk steel -: Drg No. FD-84(m),1004

M & L for removing UNSV top from table office clk steel and S&F of new top made out of Pre laminated particle board 18/19mm thick exterior grade of approved make and beaded with 4mm thick teak wood beading complete all as specified and directed.

M & L for removing UNSV drawer from table office clk steel and S&F new drawer made of 1mm thick PBI sheet and all as specified and as directed.

M & L for removing UNSV leg and S & F New leg made of MS square pipe 25mm and 1.6mm thick rest all as specified and as directed.

M & L for removing UNSV hard PVC shoes from table office clk and S&F new PVC shoes four Nos in each table and all as specified and directed.

M & L for removing UNSV stiffener and S & F new stiffener made out of MS square pipe 25mm and 1.6mm thick of Qty 03 in each table rest all as per drg and as directed.

M& L for spot welding to Table office clk complete all as directed

Table Steel 3'X2' with & w/o drawer :- Drg No. FD-1007,1008

M & L for removing UNSV top from Table Steel 900X600X760mm with and without drawer and S&F of new top made out of Pre laminated particle board 18/19mm thick exterior grade of approved make and beaded with 4mm thick teak wood beading complete all as specified and directed.

M & L for removing UNSV drawer from table 900x600'x760mm steel with drawer and S&F new drawer made of 1mm thick PBI sheet all as specified and as directed.

M&L for removing UNSV leg and S & F New leg made of MS square pipe 25mm and 1.6mm thick rest all as specified and as directed.

M& L for spot welding to Table Steel 900x600x760mm complete all as specified and directed.

M & L for removing UNSV hard PVC shoes from Table Steel 900x600x760mm and S&F new PVC shoes four Nos in each table all as specified and directed.

Removing UNSV stiffener and S & F new stiffener made out of MS square pipe 25mm and 1.6mm thick of Qty 03 in each table rest all as specified and as directed.

Chair CBA Steel with Arms Drg No. FD-75

M & L for removing UNSV seat from chair steel tubular and S&F new seats made out of 2nd class seasoned teak wood duly Canned with half round plastic cane 2mm wide 0.4mm thick and perimeter woven with 3mm wide 0.5mm thick cane and painting with black synhetic enamel paint rest all as specified and directed.

All as per item No. 24.01 above but back.

M & L for removing UNSV MS cleats from chair CBA steel and S & F new MS cleats of size 50 X 25 X3mm, 4 Nos each chair on seat and back by welding to rest the seat complete all as specified and directed.

M & L for removing of old UNSV arms rest from chair CBA steel and S&F new arms rest made out of 2nd class seasoned hard wood duly painted with synthetic enamel paint fitted with appropriate screws all as specified and directed.

Locker Bed Side Steel : Drg No. FD-257,1029

M & L for removing UNSV handle from locker bed side steel and S&F stainless steel chromium plated handle 100mm of approved quality 2 Nos each all as specified and directed.

M & L for removing UNSV hasp and staple from locker bed side steel and S&F new Aluminium hasp and staple 100mm with appropriate screws all as specified and directed.

M & L for removing UNSV shelf from locker bed side steel and S&F new shelf made out of MS sheet 1.6mm thick all as specified and directed.

M & L for removing UNSV hanging rod from locker bed side steel and S & F CP Hanging rod 19mm dia 1.6 mm thick as approved and all as specified and directed.

M & L for removing UNSV legs from locker bed side steel and S&F of new leg made of 1.6mm thick MS sheet made to shape duly painted with two coats of OG synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Charpoy MS Tubular with ply top : . Drg No. FD-CWE/Tez/FD-04

M & L for Removing UNSV Head/ foot Board from charpoy tubular steel and S&F new foot/ head board made out of 18mm thick pre-laminated particle board exterior grade of approved make and all as specified and as directed.

M&L for removing of UNSV Stiffeners from charpoy tubular steel and S&F 2 Nos new stiffener made out of 25 x 25 x 900 x 16 Gauge MS Tube welded in between long rail complete all as specified and as directed.

M & L for removing of UNSV ply wood from charpoy MS tubular and S&F ply wood 12mm thick commercial BWR of approved make with appropriate nut and bolt with washer complete all as specified and as directed.

M& L for spot welding to Charpoy Tublar with ply top complete all as specified and directed.

Painting :- M&L for removing the rusty surfaces, denting and applying putty to smoothen the surfaces and apply paint synthetic enamel OG of approved make all as specified and as directed for following:-

Almirah large steel (Drg No. FD,1031,1033)

Almirah med steel (Drg No. FD- 1032, 1034)

Chair CBA Steel with arms (Drg No. FD-75)

Charpoy MS Tubing with ply top (Drg No. CWE/Tez/FD-04)

Locker bed side steel (Drg No. FD-1029)

Rack side 3/4 space steel (Drg No. FD-1023)

FMN Set

Form with back/ without back

Table 3'x2' with or without drawer steel (Drg No. FD-1007, 1008)

Table office clk steel (Drg No. FD-1004)

Table offie offrs steel (Drg No. FD-1003)

M/S Inder SINGH SABARWALL

M/S Manjit Singh

D G Corporation