REPLACEMENT OF EXISTING CEMENT ROOFING SHEETS OF DUMMY STORE, IED MODEL ROOM AND IWTs OF WEAPON TRAINING SECTION AND CERTAIN REVENUE AND MINOR WORK AT IMA DEHRADUN.

Amount

Demolition of cement concrete floors and not exc 15cm thickness (below or above ground level ) all as specified and as directed.

M&L for 25mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in floor and finished even and fair complete all as specified.

M&L for 10 mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:3 and finished even and fair for receiving tiles complete all as specified.

M&L for screed bed or bedding layer 20mm thick in cement mortar 1:4 for laying floor finishes complete all as specified.

M&L for Machine cut kota stone slab flooring 18-20 mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for machine cut kota stone slab flooring 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified.

M&L for Rendering 15mm thick in two layer (10+5 mm) on brick work or concrete surfaces in cement mortar 1:4 finished even and fair without using extra cement including mixing of integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified. (Water proofing compound to be measured and paid for separately).

M&L for Rendering 10mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified.

M&L for applying two coats of cement base paint on walls including preparation of newly plastered surfaces complete all as specified.

M & L two coat of Oil bound distemper including a coat of primer of approved make including preparation of newly plastered surfaces of wall.

Supply only liquid water proofing compound complete ISI marked all as specified.

M&L for Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing;frame work for water tanks,cup Board etc and similar work conforming to Fe 290 Gd E-165 complete all as specified.

Dismantling timber scantling sectional area 40 sqcm and over in section in any position framed work complete all as specified.

M&L for rolled mild steel work of angle iron/ hollow pipe as in truss , purlins , frames of doors & Cup Board etc conforming to grade Fe 410-O or Fe-310-O complete all as specified.

M&L for providing cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) for filling in the pressed steel door frame/hold fast complete all as specified.

Dismantling wall and ceiling boards (fibre, pulb, insulation etc) or insulation boards slabs/blankets any thickness including cover fillets all as specified and as directed.

Material and labour for suspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system) of grid size 600mmx600mm with main runner 38 mm x 24 mm x 0.90 mm thick and wall angle 24mm x 24mm x 0.55 mm thick using 4mm thick high Pressure Non Asbestos Fiber Cement decorative Board (E-Board Classic) in a grid of GI systtem duly suspended with 4 mm dia GI bar hanger fixed with steel dash fasteners or iron purline from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts, sprinkler, smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. The last hanger at the end of each main runner should not be interlocked between main runners @ 610mm c/c, as to form 600 mm x 600 mm grid all as specified and directed. Make : Everest Industries Ltd or equivalent as per IS 14862 all as specified and directed.

Dismantling of asbestos cement (Corrugated or semi corrugated etc) as in roof covering all as specified and directed.

Supply and fix Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick conforming to relevent IS of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed (Profile and colour as approved by GE)

Supply and fix Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick conforming to relevant IS of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for preparation of new steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over and including a coat of zink chrome primer complete all as specified.

Demolition of brick/stone masonry built in CM. complete all as specified.

M&L brick work with sub class B bricks (Using old size Brick) strength 150 Kg/cm2 straight or curved on plan to any radius built in CM 1:6 bricks all complete all as specified.

M&L for providing 50 mm thick cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) as in plinth protection laid in alternate bays (n exc 2 Sqm each ) and finished even and smooth without using extra cement complete all as specified.

Surface excavation n,exc. 30 cm deep and averaging 15 cm deep and getting out in any type of soil all as spd

Excavation in trenches n. exc 1.5m wide and n. exc 1.5 m depth for foundation or for shaft etc n. exc 10 sqm on plan and n.exc 1.5m in depth and getting out in any type of soil complete all as specified & directed.

Returning, Filling in, with excavated soil including spreading leveling, watering and well ramming in layers not exc 25cm thick in any type of soil complete all as specified & directed.

Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed at a level n exc 1.5m above the starting point

M&L PCC 1:4:8 type D-2 (40 mm graded crushed stone aggragate) as in sub base filling and mass concrete complete finished even and fair all as specified and directed

M&F for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for rough finished concrete surfaces complete all as specified and directed.

M&L Formwork to sides of pillars, posts, struts, piers, columns and stanchions, for flat & rough finished surfaces of concrete complete all as specified

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for flat & rough finished surfaces of concrete Complete all as specified

M&L for TMT bar 10 mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for column and binding with wire 0.90 mm dia (anneded) complete all as specified

All as per item No 34 but 8 mm dia as in stirupps, spacers and binders complete all as specified

M&L for reinforced cement concrete type A-1 1:1.5:3 (20 mm graded aggregate ) as in foundations, including rafts, footings, bases for columns, etc. all as specified.

All as item No 36 above but as in Columns, pillars, piers, posts and struts etc

All as item No 36 above but in Beams, cantilevers, bressummers, lintels, etc over 1.5m span

M& L for Rendering 15 mm thick on fair face of brickwork or concrete surface in CM (1:4) using WPC and finishing the surface even smooth without using extra cement.

M& L for Rendering 15 mm thick on fair face of brickwork or concrete surface in CM (1:6) and finishing the surface even smooth without using extra cement including complete all as specified and directed.

M&L for applying 3 thick damp proof wall care putty as per manufacturers instruction, Preparation of puttied wall / ceiling by mechanical sander/grinder and applying two coats of oil bound emulsion distemper over a coat of primer complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surfaces and a coat of 3mm thick white cement base water proof putty including sanding/grinding complete all as specified and directed

M&L for 100mm thick PCC 1:4:8 type D2 (using 40mm graded crushed stone agg) as in sub-bases all as specified and directed.

M&L for Glazed ceramic coloured tiles of size 600x300x7mm thick, as in vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in pointed in epoxy coating grout to match including rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:6 for receiving wall tiles and dismantling of existing tile complete all as directed.

M&L for full body Vitrified ceramic coloured tiles 8 to 9mm thick (Square or rectangular) polished, area of each tile n exceeding 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in epoxy coating grout to match the shade of tiles laid over and including 15 mm thick screed bed or bedding layer in CM 1:4 including dismantling floor hearth or wall tiling including cement mortar bedding complete all as specified and directed.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid both side prelaminated decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge.

M&L 35mm thick factory made solid WPC (Wood plastic composite) both side prelaminated door shutter (single door piece to be used) with wire mesh in any number of division with brown wood grain texture, including stainless steel wire shall mesh be fixed with 15x15 Square tube in side rails with screwing 8x28 heat metal zink coated screws can be remove or fix again after changing of wire mesh when needed. The density shall be as per manufacturer instruction complete all as specified and complete all as specified and complete all as specified and directed.

S&F Butt hinges, 100 mm long, stainless steel class 'B' with galvanised stainless steel hinge pin anodised and fixed complete all specified as directed

S&F 150mm stainless steel handles, fabricated type, complete all as specified and directed.

S&F 200mm long stainless steel, barrel tower bolts (round type) of extruded section complete all directed.

S&F 250mm long Stainless steel, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections and fixed complete all as specified and directed

M&L for aluminum alloy powder coated standard hollow section as mentioned below window frame (Bombay sliding) with two glazed shutter and one Nos wire gauged shutter sliding type, with aluminum sections as per Series-B (18mm) 3 track of Jindal section numbers for sliding windows, and glazed with tinted glass coloured glass 6mm thick, fixed with glazing clips, rubber beading / gasket anodised beading, screw and lock type 2 Nos aluminium handle of size 75mm and locking system including aluminium grill of 5mm thick, average width of aperture 50mm and SS wire cloth 0.46mm dia of wire and 1.40 aperture etc complete all as specified and directed.

S&F 300mm mild steel ordinary rat tail rod pattern spring including roller and roller plate fixed to wooden/mild steel chowkhat complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 using 20 mm graded crushed stone aggregate as in plinth protection or similar places, and finishing the surface even and smooth without using extra cement including making joints 12mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with sealing compound including necessary formwork complete all as specified and directed.

S&F 4mm thick E-board false ceiling (Classic) including galvanised colour coated snap grid frame as per IS and or manufacture's instructions for false ceiling, size of grid 605x 605mm fixed with 1.6 mm dia GI wire suspenders one end tied to roof members and other end connected to main tee of grid framework including cover fillets etc complete all as directed.

M&L for hard core of brokenstone or of gauge exc 63 mm but n,exc 100 mm deposited, spread and levelled in layers n.exc 15 cm thick,water and rolled /rammed to true surface

Providing cement concrete 1:2:4 type B-1(20mm graded aggregate) as in coping, foundation etc all as specified and directed by Engr-in-charge.

M&L for sand cushioning under floors including watering and consolidation . complete all as specified and as directed.

S& F coloured machine vibro mechenically floated glossy finish interlocking cement paver block,any shape and size confirming to IS 15658-2006 of 60mm thickness,M-35 Grade with,topping of cement mixed with imported pigment,colour and shape shall be approved by GE, ISI Marked.

Material and labour ultracharged/double charged Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white epoxy tile grout and or coloured cement to match complete all as specified.

M&L for screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 laying floor finishes complete all as specified.

M&L for screed bed or bedding layer of mortar 20mm thick in cement mortar 1:4 laying floor finishes complete all as specified.

Material and labour for point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLSH having multi stranded copper conductor of 1.5 sq mm nominal cross sectional area drawn in including Non regid PVC metallic conduit with all fitting and fixing accessories and 1.5 sq mm PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to earth dolly by providing suitable lugs with & including modular metal flush box and outer cover and frame for mounting modular switch, regulators etc complete for the following. Note: (i) The quoted rates shall be deemed to be inclusive for making good to the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. (ii) Point wiring & earth wire shall be connected to each & every sunken box.

One light point controlled by one, one way switch 5 Amps

One fan point/ exhaust fan point controlled by one, one way switch 5 Amps

One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board.

One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

All as per item No 73 above but with stranded copper conductor 4 Sq mm (nominal area), two single core, PVC insulated cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet, independent, including PVC insulated stranded copper conductor 4 Sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly.

Supply and fix modular switch 1 way 10A, 1 Module

Supply and fix modular switch 1 way 20A, 1 Module with indicator lamp

Supply and fix modular socket 10A, 2/3 pin combined 2 Module

Supply and fix modular socket 10A/20A, 2/3 pin combined 2 Module

Supply and fix modular fan regulators step type 2 module 120W .

Material and labour for ceiling rose, 63.5 mm dia, ISI marked, three terminal of polycarbonate/isolated body complete all as directed.

Supply and fix Sheet metal enclosure for DB`s SPN, with 200amps rated bus br, 12 way, 240 volts double door Make Standard/HPL/Legrand, complete all as specified & as directed by Engineer- in -Charge.

S & F wall mounted Fan400 mm sweep ,1350 RPM high speed and 65CMM Air Delivery noiseless ,strudy base and thermal overload protection ,voltage 230 Volts ,50 Hz, energy saving model single phase copper wound motor, white in colour complete with blade, complete all as specified and directed. Model and make approved by GE

Supplying, fixing & testing LED 34/ 36 Watts, 2' x 2' surface mounted ceiling light fitting, warm/ natural/ cool white as per requirement at site with glare free uniform illumination with electronic driver etc and all accessories pre wired including connecting to source complete all as specified & directed. Make- POLARIS NIO III LCTLSNE- 36 - FO- CDL Crompton/ PLUTO PANEL (SURFACE) of approved make

Supply and fitting LED street light fitting 35 Watt 230 V AC outdor type with high presure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with iinpact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete

Material and labour for earthing with galvanised steel earth plate electrode 60cmX60cmX 6mm thick burried directly in ground (earth pit not less than2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to 4mm thick GI wire by means of nuts,bolts,check nuts & washers of galvanized iron or steel,protected by 15mm bore light grade galvanised iron pipe and connected to main switch board,including all necessary excavation & earth work in hard dense soill including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternate layers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover10mm thick hinged to CI frame and 6mm MS rod for handle and necessary testing complete all as shown in electrical plate No 3 of SSR part-I all as specified and directed.(one earthing for each main Panel )

S & F sub main wiring with 2 run PVC insulated unsheathed FRLSH cable 1100 Volt grade, with multi stranded copper conductor drawing in existing Concealed conduit including one run PVC insulated unsheathed cable with multi stranded copper conductor as a earth continuity and connected upto DB of following sizes complete all as specified and directed. Note:Two run of single core PVC cable with one run of earth conductor & condiut shall be measured as one unit.

2 x 6 Sqmm + 1 x 6 sqmm

Supply and fixing round shape 15 watt 220 volts AC Surface munted type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.

S & F MCB DB 16 WAy complying with IEC 61439 -1 & 3., sheet metal enclosures double door .The DBs should be supplied with tin platted insulated copper bus bar rated for 100A. 240 volts 2 in 1 shutter (Metal Door) with IK09 type with blanking plates where required and IP 43 degree protection, .

S & F MCB SP /SPN complying to IS/IEC 60898, 240 volts 'C' Curve 10 KA with energy limiting class 3. The MCB shall have 50% lower watt loss as required by IS/IEC 60898 from 6A to 63A of following capacity.

MCB SP 240 volts, 50 Hz capacity 6-32 Amps

SPN 240 volts, 50 Hz capacity 63 Amps

S & F in repair Distribution boards epoxy powder coated TP & N (VTPN MCCB DB) fabricated from minimum 1.6 mm thick CRCA sheet and fixed/ flush to wall and suitable for universal mounting with 250 Amps fully insulated copper Bus Bar for each phase and 02 neutral shrouded bar ,2 earth bar and cable tie for cable management with reversible door for IP-43 DB,S protection,415 volt ,suitable for fixing FP MCCB 100/125 Amps as incomer and 24 SP MCBs or 4/8/ 12 TP MCBs (or any combination of SP/TP MCBs) outgoings of following capacity and making good the distrubed surface complete all as directed. Note: Suitable MCCB and outgoing MCBs will be measured separately under relavant items of this schedule)

4 Way VTPN DB (FP MCCB +12 MCB, C Type).

S & F MCCB ,4 pole ICS=100% ICU at 415 volts with rupturing capacity 16 KA with thermal-magnetic release and adjustable overload setting . The MCCB shall have a Mechanical life = 40000 operations & Electrical life = 8000 operations of following capacity complete all as directed.100 Amps

ACE BUILDERS AND CONTRACTORS (BID ID -3450677)

Pragati Enterprises (BID ID -3456399)

V R Associates (BID ID -3448914)

M/S S P BUILDERS (BID ID -3450192)

M/S PUNDIR BUILDERS (BID ID -3451051)

Aron Water Proofing and Pest Control (BID ID -3450345)

M/S RAJESH KUMAR GOYAL (BID ID -3450761)

Meher enterprises (BID ID -3450665)