PROVN OF TILING OF BLDG NO.TN-5 (VEG STORAGE SHED) AT BARRACKPORE UNDER GE BARRACKPORE

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premises complete all as specified and directed.

Demolition of cement concrete in ground floor not exceeding 15 cm thickness (below or above ground level) unreinforced complete all as specified and directed.

M&L for 50mm thick PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in subbase to floor complete all as specified and directed.

S&F for non-skid (joint free) ceramic coloured (colour & shade as approved by GE) tiles of 7 to 8mm thick exceeding 0.11 Sqm but not exceeding 0.18 Sqm each (square and rectangular) as in floor, set over and including 15 mm screed bed in cement mortar (1:6) and jointed in neat cement slurry and pointed in colour cement with pigment to match the colour of tiles complete all as specified and directed.

All as per Item No.4.00 here-in-before but in area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm as in skirting/dado, wall/vertical surfaces etc over and including a backing coat of 10mm thick plaster in cement mortar (1:4) complete all as specified and directed.

S&F for glazed ceramic coloured wall tiles (vertical) 450mmX300mmX7mm set and jointed with neat cement slurry and pointed in colour cement to match over and including 10 mm thick screed bed of cement mortar (1:4) complete all as specified and directed.

M&L for pre-polished chequered cement concrete tiles 30cm x 30cm x 25mm thick (glossy type), set, jointed and pointed in neat cement slurry in floors with grey cement and pigments over 15 mm thick cement screed bed in cement mortar (1:6) complete all as specified and directed.

M&L for brick work with subclass 'B' bricks straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6) all as specified and directed

M&L for brickwork with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for applying two coats of distemper oil emulsion over a coat of alkali resistant primer after preparation of newly plastered surfaces of walls complete all as specified and as directed.

S&F for false ceiling with exposed metal (PPGI) framework/ “Tee” Grid providing and fixing of suspended Tee gird false ceiling using “T” Gird System – powder coated GI (PPGI) exposed grid false ceiling suspension system in grid size 600mm x 600mm with main runner 32 x 24mm x 0.3mm thick, cross tee 26mm x 24mm x 0.3mm thick and wall angle 24mm x 24mm x 0.40mm thick using 4mm thick non asbestos fibre cement board (oceanic) of size 595 x 595mm, an asbestos Free fibre cement board manufacture using high Pressure System Curing technology. T gird Framing is suspended using 4mm GI/MS bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip, also providing provisions for light fixtures, air conditioning diffusers and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last hanger at the end of each main runner should not be placed at not more that 300mm from the adjacent wall. 1220mm/600mm Cross Tee to be interlocked between main runners @ 600mm c/c, so as to from 600mm x 600mm or 1200mm x 600mm grid, confirming IS 14862 & type B category III of ISO 8336, tested as per AS 1530 part – 3 & B. S- 476 part 4,5,6,7 & 8 should be placed in Gird module to form all complete as per the drawing & directions of Engineer-in-Charge.

RAJ TRANCON

B N ENTERPRISE

M/S PAUL CONSTRUCTION

S S ENTERPRISE

TAMALIKA ENTERPRISE

S..S. ELECTRIC CO.