C/o Proposed Second Floor khel khud Parisar near Shiv Mandir Ward No 03, Badripur, Paonta Sahib,Phase 2

Amount

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately. Sal wood (Code No. 9.1)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with Aluminium frames/beading/EPDM rubber / neoprene gasket/lock, handel, /chitkani/Partation board/screw etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). (Code No. 9.53)

15 mm cement plaster on the rough side of single or half brick wall of mix. 1:6 (1 cement: 6 fine sand). (Code No. 13.2.2)

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joint with white cement and matching pigment etc., complete

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours,shades except burgundy, bottle green, black of any sizeas approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.(Code No. 8.31)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (Code No. 13.80)

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work.

wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats. (Code No. 13.83.2.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws.35 mm thick shutters.Second class teak wood. (Code No. 9.27.

Polishing on wood work with ready mixed wax polish of approved brand and manufacture.New work. (Code No. 9.62)

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete. 300x16mm (Code No. 9.62.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete. 150mmx10mm

Providing and fixing ISI marked, IS : 1341, M.S. heavy weight butt hinges with necessary screws etc. complete : 100x75x3.50 mm (Code No. 9.56.2.

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete.100 mm. (Code No. 9.66.2.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter. (Code No. 12.41.2

Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc.100 mm diameter. (Code No. 12.38.1

Providing and fixing water closet squatting pan (Indian corner type lipped front urinal basin of 430x260x350 mm and 340x410 x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required. (Code No. 17.4.1) One urinal basin with 5 litre automatic flushing cistern .

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore.(Code No. 18.50.1

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: (Code No. 17.7 White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

White Vitreous China Flat back wash basin size 450x 300 mm with single 15mm C.P. brass pillar tap

Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately. (Code No. 18.48.A

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS :13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (Code No. 12.41 75mm nominal size

110mm nominal size

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. (Code No. 12.42 75 MM

110mm nominal size

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall. (Code No. 18.11 15mm (fifteen millimeters) nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) (Code No. 18.4615mm (fifteen millimeters) size.

Equal Tee (Code No. 18.92 Page No.294) For 15.88 mm

For 22.22 mm

Reducing Tee. (Code No. 18.93.1 For 22.22 mm x15.88 mm outer dia

Valve Connector. (Code No. 18.98 For 15.88 mm outer dia x 15 mm nominal dia threaded

For 22.22 mm outer dia x 15 mm nominal dia threaded

Female elbows:-(Code No. 18.99 For 15.88 mm outer dia x 15 mm nominal dia threaded

For 22.22 mm outer dia x 15 mm nominal dia threaded

Male thread connector:-(Code No. 18.97 For 15.88 mm outer dia x 15 mm nominal dia threaded

For 22.22 mm outer dia x 15 mm nominal dia threaded

Female thread connector. (Code No. 18.96.2 For 15.88 mm outer dia x 15 mm nominal dia threaded

For 22.22 mm outer dia x 15 mmnominal dia threaded.

Couplers 1216

7.50% for electrical

Couplers 1620

GAGAN KUMAR (BID ID -598304)

jagdish (BID ID -597429)