Tender For HiTECH TOILET BLOCK AT MASONIC LODGE MUSSOORIE

Earth work in excavation by mechanical means (Hydrulic Excavat in foundation trenches or drains(nit exeeding 1.5 m in width or 1 including dressing of sides and ramming of bottoms, lift upto 1.5 out the excavated soil and disposal of surplus excavated soil as dir of 50 m, All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering. All work upto plinth level. 1:4:8( 1 Cement:4 coarse sand: 8 graed stone aggregate 40 mm nominal size)

Supplying and filling in lpinth with Jamuna sand under floors including, watering, ramming consolidating and dressing complete

Treatment of soil under exisiting floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 ( 1 cement : 2 Coarse sand) to match the existing floor with Chlorpyriphos/Lindance E.C 20% with 1%

Brick work with F.P.S bricks of class designation 75 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 Coarse sand)

Brick work with F.P.S bricks of class designation 75 in Superstructure above plinth level upto floor 2 level in all shape and sizes in Cement mortar 1:6 ( 1 Cement : 56 Coarse Sand)

Half brick masonry with F.P.S bricks of class designation 75 in superstructure above plint level upto floor III level in cement mortal 1:4( 1 Cement : 4 Coarse Sand)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement-All work upto plinth level in 1:1:2( 1 cement: 1 Coarse sand : 2 graded stone aggregate 20 mm norminal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landing, balconies, shelves, chajjas, lintels ,bands , plain window sills, staircases and spiral stair cases above plinth level upto floor five level, excluding the cost of centering, shuttering, finishing and reinforcement: 1:1:2( 1 Cement: 1 coarse sand(Zone III): 2 graded stone aggregate 20 mm nominal size)

Reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars.

Centring and Shuttering including strutting, ropping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Centring and Shuttering including strutting, ropping etc. and removal of form for Centring and shuttering for Suspended floors, roofs, landings, balconies and acess platform.

Centring and shuttering including strutting,ropping etc. and removal of form for columns, pillars, piears, Abutments, Posts and Struct.

Providing and fixing pressed steel door frames conforming to IS:4351, manufactured from commercial mild steel of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle thrshold of mild steel angle of section 50X25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed built higes 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface. Fixing with adjustable lugs with split end tail to each jamb

Roviding and fixing pressed steel door frames confirming to IS : 43 from commercial mild steel sheet of 1.25 mm thickness including h jamb, bead and if required angle threshold of mild steel sigle angle of se or base ties of 1.25 mm pressed mild steel welded or rigidly fixed t mechanical means, adjustable lugs with split end tail to each jamb butt hinges 2.5 mm thick with mortar guards, lock strike-plate and as specified and applying a cost of approved steel primer sfter pre surface as directed by Engineer-in-charge. Profile B

Steel work welded in built up section/framed work including cutting in position and applying a priming coat of approved steel primer us required, in gratings, frames, guard bar, ladder, raillings, brackets, gates and similar works.

Providing and laying cement concrete in retaining walls, return walls (any thickness) including attached pilasters, columns, piers, abutmets, pillars, posts, struts, buttresses, string of lacing courses, parapets, coping bed blocks, anchor blocks, plain window sills, fillets etc upto floor five level, excluding the cost of centring, shuttering and finishing in 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

15 mm cement plaster of mix in 1:6 ( 1 cement : 6 fine sand)

12 mm cement plaster of mix in 1:6 ( 1 cement : 6 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufactuer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and laying integral cement based water proofing treat including preparation of surface as required for treatment of balconies, terraces etc. consisting of following operations : a) Apple a slurry coat of neat cement using 2.75 kg/sqm. Of cement ad with water proffing compound conforming to IS. 2645 and appro by Engineer-in-charge over the RCC slab including adjoining upto 300mm height including cleaning the surface before treatm b) Laying brick bats with mortar using broken bricks/brick bats 25 to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 sand) admixed with water proofing compund conforming to IS : 2 and approved by Engineer-in-charge over 20 mm thick layer cement mortar of mix 1:5 ( 1 cement : 5 coarse sand) admi water proofing compound conforming to IS : 2645 and appro Engineer-in-charge to required slope and treating similarly th walls and slabs C) After two days of proper curing applying a sec coat of cement slurry using 2.75 kg / sqm of cement admixed water proofing compound conforming to IS : 2645 and appro Engineer-in-charge. D) Finishing the surface with 20 mm thic jointless cement mortar of mix 1:4 ( 1 cement : 4 coarse san admixed with water profing compount conforming to IS : 264 approved by Engineer-in-charge including laying glass fibre cl approved quality in top layer of plaster and finally finishing the surf with trowel with neat cement slurry and making pattern of mm square 3 mm deep. E) The whole terrace so finished sha flooded with water for a minimum period of

Providing and applying plaster of paris putty of 2 mm, thickn plastered surface to prepare the surface even and smooth complet

Providing goal 75X75 mm in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 atone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 ( 1 cement : 3 fine sand) as per standard design. In 75X75 mm deep chase

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorpition less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600X600 mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvillinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Floor painting with floor enamel paint of approved brand manufacture of required colour to give an even shade : 13.66.1 Two or more coats on new work

Fixing glazed/ceramic/Vitrified floor tiles with cement based high polymer modified quick-set tiles adhesive (water based) conforming to IS : 15477, in average 3 mm thickness

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 600X600 mm

Providing and fixing ISI marked flush door shutters conformings to IS : 22.2 (Part 1) non-decorative type, core of block board construction with frames of wood and well matched commercial 3 ply veneering with vertical g brands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvillinear portions of the building, for all heights and all levels etc. including : C) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, festeners, SS 316 Pine and anchor bolts of approved make in SS 316, Nylon separators to prevent to prevent bi-metallic contacts all complete required to perform as per sepcification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testting in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and proctection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminiun items. The Contractor shall provide cutain wall with aluminium composite panel cladding, having all the performance characteristics all complete, as per the Architectural drawings, as per item description, as spacified, as per the approved shop drawings and as directed by the Engineer-in-charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminium Composit Panel Cladding

Providing and fixing aluminium sliding door bolts ISI marked anodi coating not less than grade AC 10 as per IS : 1868 ) transparant or colour with shade with nuts and screws etc. complete, 300X16 mm

Providing and fixing aluminium handles ISI marked anodised (anod less than grade AC 10 as per IS : 1868 ) transparant or dyed to req shade with necessary screws etc. complete : 125 mm

Providing and fixing aluminium tower bolts ISI marked anodised ( a not less than grade AC 10 as perIS : 1868) transparant or dyed t or shade with necessary screws etc, complete 250X10 mm

Providing and fixing aluminium handles floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparant or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade

Finishing walls with textured exterior paint of required shade, New work ( Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm.

Painting wood work with Deluxe Multi Surface Paint of reqired shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.75 ltr/ 10 sqm of approved brand or manufacture

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer spplied @ 0.80 ltr/ 10sqm of approved brand or manufacture

Providing and fixing glass panels with putty and glazing clips in steel doors, windows, clerestory windows all complete. With 4.0 mm thick glass panes.

Windows using galvanised M.S. wire gauge with average width of a in both directions with wire of dia. 0.63 mm. With 12 mm mild steel U beading.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entrie length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation compete, including the cost of providingsnd fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS : 4454 - part 1 and M.S. top cover of reqiured thickness for rolling shutters. 80X1.25 mm M.S. laths with 1.25 mm thick top cover

Random rubber msonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement :6 coarse sand :12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortr 1:6 ( 1 cement : 6 coarse sand)

Demolishing cement concrete manually/ by machanical means including disposal of material within 50 meters lead as per direction of Enigineer-in-charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechnical means including stacking of steel bars and disposal of unserviceable material within 50 mitres lead as per direction of Engineer-in-charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantiling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architeave, holdfasts etc. complete and stacking within 50 metres lead : of area 3 sq. metres and below

Dismantiling tile work in floor and roofs laid in cement mortal including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Dismantiling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead

Finishing walls with textured inner paint of required shade, New work ( Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 100 mm diameter

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 75 mm diameter

Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10X10 10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and cost of cutting holes and making good the walls etc. 100 mm diameter

Providing and fixing Urinal CODE : URS-WHT-13261 Size : 355X340X535 mm with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required. One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing Tankless Wall Hung WC With Sensor Flush, UF Soft Close Slim Seat Cover, Hinges, Accessories Set, Size: 360X580X380 mm (OPS-WHT-15961BIUFSMTL) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors

Providing and fixing Thin Rim Table Top Basin, Shape - Triangular, Size : 600X41X100 mm with C.I. brackets, approved quality (jagur and etc.)

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fitting

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. internal work Exposed on wall 15 mm dia. Nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc (external work) 15 mm dia. Nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc (external work) 20 mm dia. Nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete 20 mm nominal bore

Providing and fixing jaquar Alive Bib Tap of approved quality (jagur and etc) conforming to IS : 8931. 15 mm nominal bore

Providing and fixing jaquar Alive Angular stop Valve With Wall Flange for basin mixer and geyser approved quality (jagur and etc) conforming to IS : 8931. 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm dia Sensor Faucet for Wash Basin(CODE : SNR-CHR-51001SQ) of approved quality and make (jagur and etc), including painting of fitting and brackets, cutting and making good the walls

Providing and placing on terrace (at all floor levels) polyethylene water tank ISI : 12701 marked with cover and suitable locking arrangement in tank and necessary holes for inlet, outlet and overflow pipes but without fitting base support for tank

Providing and fixing PTMT soap Dish Holder having length of 138m 102mm, height of 75mm with concealed fitting arrangements weig than 106 gms

Providing and fixing 600X450 mm bevelled edge mirror of superior quality) complete with 6 mm thick hard board ground fixed to woo C.P. brass screws and washers complete.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden, 600 mm long towel rail with total length of 645 mm, width 78mm and effective height of 88mm, weighing not less than 190gms.

Providing and fixing PTMT grating of approved quality and colour. Circular type. 100 mm nominal dia.

providing and fixing ball valve (brass) of approved qulity complete. High or low pressure with plastic floats. 15 mm norminal bore.

providing and fixing ball valve (brass) of approved qulity complete. High or low pressure with plastic floats. 20 mm norminal bore.

Constructing brick masonry manhole in cement mortar 1:4( 1 cement :4 4 coarse inside size 60x45x50cm. Inside inculding C.I. cover with frame(light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38kg(weight of cover 23 kg and weight of frame 15 kg): with

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C wate fittings complete. Flexible pipe 40 mm dia

Providing and fixing PTMT grating of approved quality and colour. Circular type 125 mm nominal dia with 25 mm waste hole.

Providing and fixing unplasticised P.V.C connection pipe with PTMT Nuts, collor and bush of approved quality and colour. 15 mm norminal bore with 45 cm length.

WGPVCPT point wiring in PVC conduit, with paino type switch: wiring for light point/ fan point/ Ex Fan point/ Call Bell point recessed PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq. mm FR PVC insulated copper conductor single core cable etc. as required. Group C

LPACCPT S/F light plug point piano type accessories: Supplying and fixing metal box of 150 mm x 75 mm x 60 mm deep( norminal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 anos socket outlet 5/6 amos piano type switch

WGSTLPTTC Twin control point wiring in PVC conduit, with piano type switch: wiring for twin control light point recessed PVC conduit, with piano type switch, phnolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq. mm FR PVC insulated copper conductor single core cable etc as

PPACCPT S/F power plug point piano type accessories: Supplying and fixing matel box of 180 mm x 100 mm x 60 mm deep on surface or in recess with 15Amp piano type switch and socket. Complete with all work.

MCBDPSOC20 S/f power 20A SPN MCB industrial socket outlet: Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole

WGPVCSB Circuit/sub-man wiring in PVC conduit. Wiring for circuit/ submain wiring along with earth wire with all following size of PVC insulated copper conductor, single core cable in surface/recessed PVC conduit as required 2x 2.5 sq. mm + 1x 1.5 sq mm earth wire.

WGPVCSB Circuit/sub-man wiring in PVC conduit. Wiring for circuit/ submain wiring along with earth wire with all following size of PVC insulated copper conductor, single core cable in surface/recessed PVC conduit as required 2x 2.5 sq. mm + 1x 2.5 sq mm earth wire.

WGPVCSB Circuit/sub-man wiring in PVC conduit. Wiring for circuit/ submain wiring along with earth wire with all following size of PVC insulated copper conductor, single core cable in surface/recessed PVC conduit as required 4x 2.5 sq. mm + 2x 2.5 sq mm earth wire.

CREB S/F ceilling rose : Supplying and fixing 3 pin 5 amp ceiling rose including connection etc. as reuired

Suppy and fixing PVC batten/angle holder including connections etc. as required

EARGIPL GI earth plate electrode: Earting with GI earth plate electrode: Earting with GI eath plate 600x600x6 mm thick i/c accessories and providing masonary encloser with cover plate having locking arrengement and watering pipe etc complete work

EARGIWRPIP P/F of 6 SWG GI earth wire in pipe providing and laying earth connection from earth electrode with 6 SWG GI wire in 15 mm dia GI pipe complete work.

TPMCBDB S/F TP MCB DB:4 way(4+12) Double door, hotizontal type

MCBCDB S/F C series SP MCB S/F 5 amo 32 amp rating, 415V isolator on existing DB complete with connection

MCBTPIS S/F TP MCB isolator: S/F 100 amp rating, 415V isolator on exisitng DB complete with connections.

S/F of hexagonal fan box with hexagonal side of approx 80mm in length fabricated from 16S.W.G. M.S sheet incorporating 10 mm dia. M.S bar round and duty painted with red oxide along with all work

Eraction testing of Exhaust fan complete with all work

Eraction testing of ceiling fan etc excluding supply of down rod complete in all respect

Suppy of 7w LED bulb for mounting on brass Holder.(havells catc. Ref. LHLDEUEEMC8R007 or equivalent)

Supply of E-Lite 20W LED pride Plus Neo batten. A color Changing LED batten with options of 3000 K & 6500 k , all in one fixture.(havells catc. Ref. LHEXACP7IN1WO20 or equivalent)

Supply of metallic range exhaust fan, 300 mm sweep. (havells catc. Ref. Ventil Air-DSP or equivalent)

Supply of 1200 mm sweep, 5 star rated ceiling fan.(Havells catc. Ref. ES NEO or equivalent)

Supplying of Recess/Conceal Fazer Neo LED panel Square with Ultra slim LED panels with inbuilt driver in PC body. Premium aesthetics with stepped ring bezel with integrated driver (6 W LED, 6000 K). (Firefly catc. Ref. LHEBMDP6IW1W006 or equivalent)

Supplying of Recess/Conceal Fazer Neo LED panel Square with Ultra slim LED panels with inbuilt driver in PC body. Premium aesthetics with stepped ring bezel with integrated driver (20 W LED, 6000 K). (Firefly catc. Ref. LHEBMDP7IW1W020 or equivalent)

C S RAWAT

Rajendra Prasad Bangwal