Rajasthan

Financial BO

Works

Electrical Works

Remaining MGPS Supply system at Mandore District Hospital Jodhpur

RSRDCC-GM

Jodhpur, Rajasthan

Amount: ₹10.7 LCloses: 30 Mar 2026Closed

Timeline

Published19 Mar 2026
Closed30 Mar 2026
Technical Evaluation1 Apr 2026
Financial Evaluation2 Apr 2026
Award—

Bids

Percentage

1 Bid2 Apr 2026

#	Company	Quoted %	Amount	Rank	Status
1	JK ENGINEERING WORKS L1₹10.3 LAdmitted-Finance	-3.26%	₹10.3 L	L1	Admitted-Finance

Tender Value

₹10.7 L

EMD Value

₹21,400

Closing Date

30 Mar 2026, 6:00 pmClosed

Tender Inviting Organisation

Name

General Manager RSRDC Ltd. Jaipur

Address

Office of the Project Director RSRDC Ltd. Unit-Electrical, Jodhpur. High Court Campus, Near Shatabdi Circle, Jodhpur

Work Description

Remaining MGPS Supply system at Mandore District Hospital Jodhpur

Tender Information

Tender ID

2026_RSRDC_547233_1

Reference Number

RSRDC NIT 777/2025-26 (Sl-1)

Tender Type

Open Tender

Product Category

Electrical Works

Form of Contract

Percentage

Period of Work

60 days

Location

Jodhpur

Source Website

Subscribe to view

Eligibility / Pre-Qualification

Please refer Tender documents.

Documents Required

2 documents required · 2 mandatory

Fee/PreQual/Technical

RequiredTENDER COST, PROCESSING FEE, EARNEST MONEY AND OTHER REQUIRED TENDER DOCUMENTS (.pdf)

Finance

RequiredBOQ (.xls)

Fee & Financial Details

Tender Fee Amount

₹590

Tender Fee Payable To

Through RTGS/NEFT/IMPS

EMD Fee Amount

₹21,400

Important Dates

Last Activity

2 Apr 2026

Published

19 Mar 2026

Bid Opening

1 Apr 2026

Download Starts

19 Mar 2026

Download Ends

30 Mar 2026

Submission Starts

20 Mar 2026

Bill of Quantities

PercentageBoQ_Ver3.0INR

This is a percentage-rate BOQ. The schedule below shows estimated quantities and rates. Bidders quote a single percentage above or below the total estimated cost.

BoQ1 (0 items)

Sl No	Description	Qty	Unit	Est. Rate	Est. Amount
1SITC of Dessicant Air Dryer Output Capacity - 60 cfm with UL Certified Microprocessor Controller with dewpoint based changeover option, Pre-filter rating 0.3 microns , Shuttle valve for Low Pressure drop, All Aluminium resist oxidation & scale formation, Dewpoint better than -40o C including fixing on wall with required T & P making connections etc complete in all respect.
2SITC of Compressed Air System should consist of 1 nos. Air Compressors with Electric Motors, Electrical Switch Gear and Automatic Control System of following Specifications: a)Air Compressor 1(One) Nos; Type Non-lubricated / Oil-free; Capacity 57 cfm at 8.5 kg/cm2; Cooling Air cooled b)Drive- Electric Motor 2(two) Nos; Capacity 15 HP; Speed 1440 rpm (syn.); Drive Belt drive; Electricity supply 440 volt, 50 Hz. 3 phase c)Starter Star/Delta Control & Switchgear with overload rotection.including making PCC foundation and fixing withbolts , anti vibration pad and making connections complete as required.
3SITC. of Compressed air filtration system:One set of 3 - stage filter The filters should be made of die cast aluminums housing with epoxy power paint on the outside and anodized surface treatment inside to prevent corrosion and ensure extra long life. The filters should have maximum contaminant removal efficiency with minimum pressure drop. Total 3-stage of filters should be used as mentioned below: Stage 1 : coalescing filters for general-purpose protection, removing liquid water and oil aerosol to 0.1 mg/cum. (0.1 pm) and particles down to 5 micron. Stage 2 : particular filter for dust protection, removing particles down to 1 micron. Stage 3 : high efficiency coalescing filters, removing liquid water and oil aerosol to 0.01 mg/cu.m. (0.01 pip) and particles down to 0.01 micron.
4SITC of Hot dipped galvanized ( inside and outside )Air receiver tank (as per IS:7938-1976 and upto date amendment) for compressed air system to dampen out pulsation and condense and trap the moisture in the compressed air and also to let oil and other impurities settle down before air passes into the piping with safety valve , Drain Valve , Pressure gauge and fusible plugs of 1000 litres capacity complete as required including making PCC foundation and fixing with bolts and making connections complete as required.
5SITC of MGPS of medically grade as per BSEN-13348 with third party certification from Lloyds/TUV degreased [ie free from oil, grease and particulate matters) seamless copper pipe confirming to ASTM B88 and all copper joining done by brazing with AWSA5.8, classification BCuP-S or BS 1845 following procedure in accordance with ASTM B828 after purging with nitrogen. All pipe cutting shall be carried out with a radial pipe cutter and copper pipe fitting's shall comply with B4 alloy designation. Adequate support shall be provided while laying pipeline testing shall be done at 17 bar and after testing pipe shall be painted with two coat of enamel paint as per colour codification as per ISO 7396-Part-I 2016.
6SITC of Gas outlet points (AR-4), (AR-7) and Vaccum (8.7 psig) for dispensing medical gases (oxygen/air/Vaccum) at point of use confirming to BSEN ISO 9170-1:2008. The gas outlet are quick connect type it should have colorc oding for different gas source and should accept only respective adapters as required.

Stage Documents

Stage Summary Snapshot

stage.html

html • 0.02 MB

Technical Evaluation

tech_eval.pdf

PDF

Financial Bid Opening

boq_comp_chart.xlsx

xlsx

Documents

Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.

Tender Page Snapshot

details.html

html • 0.03 MB

NIT Documents

Tendernotice_1.pdf

PDF • 0.31 MB

Work Item Documents

AgrrementRTPPandetc.pdf

Tender Documents • 2.75 MB

BankDetail00.pdf

Tender Documents • 0.17 MB

BOQ_975798.xls

BOQ • 0.28 MB

Ready to Participate?

Download all tender documents and submit your bid

Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .

Loading…

Company

JK ENGINEERING WORKS

L1₹10.3 LAdmitted-Finance

Sl No	Description	Qty	Unit	Est. Rate	Est. Amount
1SITC of Dessicant Air Dryer Output Capacity - 60 cfm with UL Certified Microprocessor Controller with dewpoint based changeover option, Pre-filter rating 0.3 microns , Shuttle valve for Low Pressure drop, All Aluminium resist oxidation & scale formation, Dewpoint better than -40o C including fixing on wall with required T & P making connections etc complete in all respect.
2SITC of Compressed Air System should consist of 1 nos. Air Compressors with Electric Motors, Electrical Switch Gear and Automatic Control System of following Specifications: a)Air Compressor 1(One) Nos; Type Non-lubricated / Oil-free; Capacity 57 cfm at 8.5 kg/cm2; Cooling Air cooled b)Drive- Electric Motor 2(two) Nos; Capacity 15 HP; Speed 1440 rpm (syn.); Drive Belt drive; Electricity supply 440 volt, 50 Hz. 3 phase c)Starter Star/Delta Control & Switchgear with overload rotection.including making PCC foundation and fixing withbolts , anti vibration pad and making connections complete as required.
3SITC. of Compressed air filtration system:One set of 3 - stage filter The filters should be made of die cast aluminums housing with epoxy power paint on the outside and anodized surface treatment inside to prevent corrosion and ensure extra long life. The filters should have maximum contaminant removal efficiency with minimum pressure drop. Total 3-stage of filters should be used as mentioned below: Stage 1 : coalescing filters for general-purpose protection, removing liquid water and oil aerosol to 0.1 mg/cum. (0.1 pm) and particles down to 5 micron. Stage 2 : particular filter for dust protection, removing particles down to 1 micron. Stage 3 : high efficiency coalescing filters, removing liquid water and oil aerosol to 0.01 mg/cu.m. (0.01 pip) and particles down to 0.01 micron.
4SITC of Hot dipped galvanized ( inside and outside )Air receiver tank (as per IS:7938-1976 and upto date amendment) for compressed air system to dampen out pulsation and condense and trap the moisture in the compressed air and also to let oil and other impurities settle down before air passes into the piping with safety valve , Drain Valve , Pressure gauge and fusible plugs of 1000 litres capacity complete as required including making PCC foundation and fixing with bolts and making connections complete as required.
5SITC of MGPS of medically grade as per BSEN-13348 with third party certification from Lloyds/TUV degreased [ie free from oil, grease and particulate matters) seamless copper pipe confirming to ASTM B88 and all copper joining done by brazing with AWSA5.8, classification BCuP-S or BS 1845 following procedure in accordance with ASTM B828 after purging with nitrogen. All pipe cutting shall be carried out with a radial pipe cutter and copper pipe fitting's shall comply with B4 alloy designation. Adequate support shall be provided while laying pipeline testing shall be done at 17 bar and after testing pipe shall be painted with two coat of enamel paint as per colour codification as per ISO 7396-Part-I 2016.
6SITC of Gas outlet points (AR-4), (AR-7) and Vaccum (8.7 psig) for dispensing medical gases (oxygen/air/Vaccum) at point of use confirming to BSEN ISO 9170-1:2008. The gas outlet are quick connect type it should have colorc oding for different gas source and should accept only respective adapters as required.

Sl No

Description

Qty

Unit

Est. Rate

Est. Amount

1SITC of Dessicant Air Dryer Output Capacity - 60 cfm with UL Certified Microprocessor Controller with dewpoint based changeover option, Pre-filter rating 0.3 microns , Shuttle valve for Low Pressure drop, All Aluminium resist oxidation & scale formation, Dewpoint better than -40o C including fixing on wall with required T & P making connections etc complete in all respect.

2SITC of Compressed Air System should consist of 1 nos. Air Compressors with Electric Motors, Electrical Switch Gear and Automatic Control System of following Specifications: a)Air Compressor 1(One) Nos; Type Non-lubricated / Oil-free; Capacity 57 cfm at 8.5 kg/cm2; Cooling Air cooled b)Drive- Electric Motor 2(two) Nos; Capacity 15 HP; Speed 1440 rpm (syn.); Drive Belt drive; Electricity supply 440 volt, 50 Hz. 3 phase c)Starter Star/Delta Control & Switchgear with overload rotection.including making PCC foundation and fixing withbolts , anti vibration pad and making connections complete as required.

3SITC. of Compressed air filtration system:One set of 3 - stage filter The filters should be made of die cast aluminums housing with epoxy power paint on the outside and anodized surface treatment inside to prevent corrosion and ensure extra long life. The filters should have maximum contaminant removal efficiency with minimum pressure drop. Total 3-stage of filters should be used as mentioned below: Stage 1 : coalescing filters for general-purpose protection, removing liquid water and oil aerosol to 0.1 mg/cum. (0.1 pm) and particles down to 5 micron. Stage 2 : particular filter for dust protection, removing particles down to 1 micron. Stage 3 : high efficiency coalescing filters, removing liquid water and oil aerosol to 0.01 mg/cu.m. (0.01 pip) and particles down to 0.01 micron.

4SITC of Hot dipped galvanized ( inside and outside )Air receiver tank (as per IS:7938-1976 and upto date amendment) for compressed air system to dampen out pulsation and condense and trap the moisture in the compressed air and also to let oil and other impurities settle down before air passes into the piping with safety valve , Drain Valve , Pressure gauge and fusible plugs of 1000 litres capacity complete as required including making PCC foundation and fixing with bolts and making connections complete as required.

5SITC of MGPS of medically grade as per BSEN-13348 with third party certification from Lloyds/TUV degreased [ie free from oil, grease and particulate matters) seamless copper pipe confirming to ASTM B88 and all copper joining done by brazing with AWSA5.8, classification BCuP-S or BS 1845 following procedure in accordance with ASTM B828 after purging with nitrogen. All pipe cutting shall be carried out with a radial pipe cutter and copper pipe fitting's shall comply with B4 alloy designation. Adequate support shall be provided while laying pipeline testing shall be done at 17 bar and after testing pipe shall be painted with two coat of enamel paint as per colour codification as per ISO 7396-Part-I 2016.

6SITC of Gas outlet points (AR-4), (AR-7) and Vaccum (8.7 psig) for dispensing medical gases (oxygen/air/Vaccum) at point of use confirming to BSEN ISO 9170-1:2008. The gas outlet are quick connect type it should have colorc oding for different gas source and should accept only respective adapters as required.