Drilling 8 inch dia. bore holes (2 Nos.) through DTH drill machine including providing and laying of submersible pump-motor complete set 7.5 HP (2no.s) and 10 HP Mono block pump (2 Nos.) complete sets with Underground water reservoir

Amount

A. Estimate for Drilling 8 inch dia. bore hole (2 No.s) through DTH drill machine including providing & laying of submersible pump-motor complete set 7.5 HP(2no.s)

Drilling of 8" dia. Bore hole by using D.T.H. drill machine.: 0-20mtr

Drilling of 8" dia. Bore hole by using D.T.H. drill machine.: 20-40mtr

Drilling of 8" dia. Bore hole by using D.T.H. drill machine.: 40-60 mtr

Drilling of 8" dia. Bore hole by using D.T.H. drill machine.: 60-90 mtr

Drilling of 8" dia. Bore hole by using D.T.H. drill machine.:90-120mtr&above upto 200 mtr.

Supplying 9" dia. pvc casting pipe as per ISI including carriage, sale tax etc. all complete jobs.

Development and yield test of bore hole by suitable air compressor of maximum 12 hour complete job.

supplying and installation of 7.5 HP submersible pump set having make - kirloskar, pullen, calama or duke, ISI marked Energy efficient discharge 140-150 lpm, Head-120mtr stage-1:- 12-15 impeller brass or stainless steel only. Suitable 8 inch dia. for borewell operation at- 3phase, 440volts, 50hz. detailed specification enclosed separately

Suitable dol starter for 7.5 HP pump sets with amp. Meter, water level guard, single phasing preventer as per detailed specification enclosed separately.

Transportation, fixing installation of pump motor sets in the borehole including testing (excluding, G.I. pipe).

Supplying havells/kirloskar/finolex or equivalent proven quality 4 core 10 sqmm pvc flat cable for submersible pump-motor sets (ISI marked).

P/F G.I Pipe complete with G.I. fitting and clamps i/c cotting and making good the walls etc. internal work exposed on wall 32 mm dia.

B. Estimate for 10 HP Monoblock pump(2 No.s) complete set in Pump house

P/F G.I. union in G.I pipe including cutting & threading the pipe and making long screws etc. complete (new work) : 2" dia: (50.8 mm nominal bore each).

P/F gun metal gate value with C.I wheel of approved quality (screwed end) : 2"(dia) (50.8 mm nominal bore each)

Supplying and installation of 10 HP monoblock pump set 3 phase, 440 volt 20-30m head.

suitable DOL starter for 10 HP monoblock pump sets

Supplying havells/kirloskar/finolex 4 core 10sqmm pvc flat cable for surface monoblock pump sets (ISI marked )

Providing suitable ICTPN switch 100 amp.

ICTPN switch 63 amp.

Providing/ F Foot valve (Gun Metal)

Providing & fixing suitable non return value (GM) 50 mm

P/F Brass Bib cock of approved quality : 15mm nominal bore

P/F G.I. pipe complete with G.I fitting and clamps I/C cutting and making good the walls: (15mm dia).

P/F G.I. pipe complete with G.I fitting and clamps I/C cutting and making good the walls: (20 mm dia).

P/F G.I. pipe complete with G.I fitting and clamps I/C cutting and making good the walls: (25 mm dia).

GI socket 2*4 inch

P/F G.I. pipe complete with G.I fitting and clamps I/C cutting and making good the walls: (50mm dia).

P/L C TYPE 75*75*5 MM angle for fabrication of base plate

C. Estimate for pump house

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 40 mm nominal size derived from natural sources).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, ifnishing and reinforcement- All work up to plinth level :1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III)derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Brick work in super structure in clay flyash brick of class designation 10 in cement mortar 1:6 above plinth level up to floor V level

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Centering and shuttering including strutting, propping etc. and removal of form forFoundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form forLintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Weather shade, Chajjas, corbels etc., including edges

12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand)

6 mm cement plaster of mix :1:3 (1 cement : 3 fine sand)

PROVIDING AND FIXING 1MM THICK MS SHEET door made of door frame 35*35*5 angle iron and shutter frame made of 30*30*5 mm angle iron from side 3 no.s horizontal braces with 20*5 mm MS flat and 1 No back side with tie on bottom door frame and 2 no.s diagonal braced back side with 20*5 mm MS Flat hinges made of 3 NO.S MS sheet 3 mm thick with pin 6 mm dia 120 mm welded with shutter 2 no.s sliding door bolt (250*16 mm )2 No.s tower bolt and 2 nO. Handle 125 mm including primer etc.

P/f 1mm thick ms window shutter means of 30*30*5 mm angle iron window frame and shutter frame made of angle iron 25*25*5 mm, 2 No.s 20*5mm MS Flat horizontal bracing and 1 no. diagonal bracced with 20*5 mm MS Flat having leap of 20*5 mm MS Flat ,grating with 12 mm square bar,7 No.s MS Handle 100 mm,2 No.s and tower bolt 150*10 mm 4 no.s hinges made of 3 m plate with 6 m dia pin including primer etc.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete : 40 mm thick with 20 mm nominal size stone aggregate

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.18 mm thick

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Colour washing such as green, blue or buff to give an even shade :New work (two or more coats) with a base coat of whiting

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Marble work gang saw cut (polished and machine cut) ofArea of slab over 0.50 sqmg (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately). Area of slab over 0.50 sqm

Lettering with black Japan paint of approved brand and manufacture

D. Estimate for Under ground water reservoir( 1 lakh litre Capacity )

EarC65:H72nual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. all kind of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 40 mm nominal size derived from natural sources).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, ifnishing and reinforcement- All work up to plinth level :1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete( Consider it as Circular section increase rate by 20%)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.(Including extra rate 20% for circular C/s)

Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing, hcisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but, excluding cost of reinforcement, with 1:1.5:3 (1 cement 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete40 mm thick with 20 mm nominal size stone aggregate

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution

D.I PIPE for waste chamber

valve for cleaning

water proofing material

Total impact of GST for the purpose of CTC