8122/SAR-04/2022-23 CONSTRUCTION OF STORAGE ACCOMMODATION AT AF STN SARSAWA , SOIL INVESTIGATION WSA BASED ON UNIT RISK PRINCIPLE (URP) AT AF STN SARSAWA AND SOIL INVESTIGATION AT 1AFSB DEHRADUN UNDER GE(AF) SARSAWA

Amount

Materials and labour for carryout soil investigation / testing profiles/ proportion to determine safe bearing capacity of sub soil by conducting bore holes 150 mm dia (STP) in sub soil strata down to 10 metres depth of refusal whichever is encountered earlier inclusive field and lab investigation according to relevant specification of IS:2131, IS: 6403, IS: 1498 and IS: 2720 (a) Mobilization of equipment and personel to proposed site shown and back (b) Collection of disturbed and undisturbed soil sample from various level of sub soil strata. (c) Sub soil penetration resistance characterstic which have been determined in situ(d) Conduction laboratory test on settled sample for different engineering properties: (i) Grain size analysis incl classification of soil (ii) Bulk and dry density (iii) Moisture content (iv) Liquid and plastic limits (Atterbergs Limits) (v) Shear tests (vi) Specific gravity (vii) C and φ value (viii) Settelments details (e) Recording ground table (sub soil water level) if observed upto exploration, max and min depth of water table, effect of sub soil water on foundation to be intimated. f) Hyderometric test sieve analysis and index properties including CBR & K value (g) Any other recording of relevent property not mentioned above effecting the structural stability if noticed. (h) Preparation, submission of technical report of copies alongwith recommendations of SBC of soil for proposed Bldg/structure at 1m below GL and thereafter at every 0.5m interval. (The Test shall be conducted as per Indian Standard codal provision). The rate include preparation and submission of the comprehensive technical report giving complete record of Investigation and calculation of Modulus of Subgrade reaction of the soil. The rates will also include excavation and back filling of pit., leading, unloading of kentledge material and removal of kentledge material after ascends, descends, crossing of tracks/nallah with all labour, material,tools plants and machinaery. complete as specified and directed Note : Applicable for Special condition Srl No 29, line No 38, page No 113: the note quated by tenderer is deemed to included in special condition if applicable shall be made without any extra cost to the Govt. Agencies:- (i) Geo Tach (ii) National Soil Testing & Research Lab(ii) Rishi Markandeshwar Engineering Consultant and (iv) Any other agencies approved by E-in-C’s. 1. 01 quantity of BOQ Sl No. 1 ,2 and 3 to be carried out at 1AFSB Dehradun under GE(AF) Sarsawa 2. Remain quantity of BOQ Sl No 1, 2 and 3 to be carried out at Air Force Station Sarsawa under GE(AF) Sarsawa

Materials & labour for conducting plate load test using of plate size 1.50m X 1.50 m x 1.50m (The load test shall be conducted as per Indian Standard codal provision). The rate include preparation and submission of the comprehensive technical report giving complete record of Investigation and calculation of Modulus of Subgrade reaction of the soil. The rates will also include excavation and back filling of pit., leading, unloading of kentledge material and removal of kentledge material after test,ascends,descends,crossing of tracks/nallah with all labour, material,tools plants and machinaery. complete as specified and directed Note : Applicable for Special condition Srl No 29, line No 38, page No 113: the note quated by tenderer is deemed to included in special condition if applicable shall be made without any extra cost to the Govt. Agencies:- (i) Geo Tach (ii) National Soil Testing & Research Lab(ii) Rishi Markandeshwar Engineering Consultant and (iv) Any other agencies approved by E-in-C’s. 1. 01 quantity of BOQ Sl No. 1 ,2 and 3 to be carried out at 1AFSB Dehradun under GE(AF) Sarsawa 2. Remain quantity of BOQ Sl No 1, 2 and 3 to be carried out at Air Force Station Sarsawa under GE(AF) Sarsawa

Materials & labour for conducting CBR (California bearing ratio) test at site (The Test shall be conducted as per Indian Standard codal provision). The rate include preparation and submission of the comprehensive technical report giving complete record of Investigation and calculation of Modulus of Subgrade reaction of the soil. The rates will also include excavation and back filling of pit., leading, unloading of kentledge material and removal of kentledge material after test,ascends,descends,crossing of tracks/nallah with all labour, material,tools plants and machinaery. complete as specified and directed Note : Applicable for Special condition Srl No 29, line No 38, page No 113: the note quated by tenderer is deemed to included in special condition if applicable shall be made without any extra cost to the Govt. Agencies:- (i) Geo Tach (ii) National Soil Testing & Research Lab(ii) Rishi Markandeshwar Engineering Consultant and (iv) Any other agencies approved by E-in-C’s. 1. 01 quantity of BOQ Sl No. 1 ,2 and 3 to be carried out at 1AFSB Dehradun under GE(AF) Sarsawa 2. Remain quantity of BOQ Sl No 1, 2 and 3 to be carried out at Air Force Station Sarsawa under GE(AF) Sarsawa

Materials & labour for conducting K- value Test using 75cm Circular Plate (The Test shall be conducted as per Indian Standard codal provision). The rate include preparation and submission of the comprehensive technical report giving complete record of Investigation and calculation of Modulus of Subgrade reaction of the soil. The rates will also include excavation and back filling of pit., leading, unloading of kentledge material and removal of kentledge material after test,ascends,descends,crossing of tracks/nallah with all labour, material,tools plants and machinaery. Note : Applicable for Special condition Srl No 29, line No 38, page No 113: the note quated by tenderer is deemed to included in special condition if applicable shall be made without any extra cost to the Govt. Agencies:- (i) Geo Tach (ii) National Soil Testing & Research Lab(ii) Rishi Markandeshwar Engineering Consultant and (iv) Any other agencies approved by E-in-C’s.

Surface dressing not exc 15cm deep in soft/loose soil complete all as specified and directed by Engr-in-Charge. Note : Removing of vegetation / shrubs / brushwood / undergrowth and carrying away rubbish to a distance of 50 m deemed to included in quoted rate.

Excavating in trenches not exc 1.5m wide and not exc 1.5m in depth; for foundation, etc or for shafts, wells, cesspits, manholes etc not exc 10Sqm on plan and not exc 1.5m in depth and getting out in soft / loose soil complete all as specified and directed.

Earth filling under floors including spreading, leveling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed. Note :- Soil obtained from excavation under item 2.00 here-in-before shall be used for filling.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25cm in soft / loose soil complete all as specified& directed by Engr-in-Charge.

Removal of excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above or below the starting point complete all as specified& directed by Engr-in-Charge.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for form work to sides of Pillars, posts, struts piers, columns etc in squarre, rectangular or polygonal, rough finished surfaces of concrete complete all as specified and directed.

M&L for formwork to chajjas, chullah hoods, self, troughs and similar items including edges for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for Reinforced cement concrete (nominal mix) in Type B1 1:2:4 (20 mm graded stone aggregate) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engr-in-Charge. Note :- Reinforcement shall be measured and paid for separately.

M&L for Reinforced cement concrete (nominal mix) in Type B1 1:2:4 (20 mm graded stone aggregate) Beams, cantilevers, bressumm ers, lintels over 1.5m span complete all as specified and directed by Engr-in-Charge. Note :- Reinforcement shall be measured and paid for separately.

M&L for Reinforced cement concrete (nominal mix) in Type B1 1:2:4 (20 mm graded stone aggregate) Columns, pillars, piers, posts and struts complete all as specified and directed by Engr-in-Charge. Note :- Reinforcement shall be measured and paid for separately.

M&L for Reinforced cement concrete (nominal mix) in Type B1 1:2:4 (20 mm graded stone aggregate) Slabs supported on walls, beams and columns in floors, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr-in-Charge. Note :- Reinforcement shall be measured and paid for separately.

M&L for mild steel TMT bars 10mm dia & over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and bending with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders & over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and bending with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed.

M&L for PCC 1:3:6 type C1 (using 20 mm gradded stone agg )as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, drain channels, copings,parapets copings, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directed.

M&L for rendering 10mm thick in cement mortar 1:6 on stone masonry surfaces or surface other than fair face of brick work of walls including finishing the surface fair and even complete all as specified.

M&L for preparation of new plastered surfaces of walls and applying two coats of Oil bound distemper over a coat of 1mm thick wall care putty of approved tint complete all as specified & directed by Engr-in-Charge.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, mixed with water proofing admixture (ISI marked) as per manufacturer’s instructions, finished even and smooth without using extra cement complete all as specified. Note : - Supply only water proofing admixture shall be measured and paid for separately.

Material and labour for preparation of new plastered surfaces and applying two coat exterior emulsion paint over a coat of primer paint complete all as specified and as directed any tint. Note: The Camouflaging Pattern decided by Engr-in-Charge

Supply only integral liquid water proofing compound (ISI marked). Make : Pidilite (Dr. Fixit Pidiproof LW) or equivalent of Fosroc / Sika / STP

M&L for 100 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for 25mm thick PCC (1:2:4) type B0 (using 12.5mm graded stone aggregate), as in sub base all as directed by Engineer-in-charge.

M&L Vetrified Ceramic tiles 10mm thick light shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match and over 15mm thick cement screeding in CM 1:6 Complete all as specified and directed by Engr-in-Charge.

M&L Vetrified Ceramic tiles 10mm thick light shade (square/rectangular) polished, area of each tiles n exceeding 0.36, in vertical surfaces as skirting and dados etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match and over 10mm thick rendering in CM 1:4 Complete all as specified and directed by Engr-in-Charge.

M&L Vetrified double charged/dark shasde Ceramic tiles 10mm thick light shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match and over 15mm thick cement screeding in CM 1:6 Complete all as specified and directed by Engr-in-Charge.

M&L Vetrified double charged/dark shasde Ceramic tiles 10mm thick light shade (square/rectangular) polished, area of each tiles n exceeding 0.36, in vertical surfaces as skirting and dados etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match and over 10mm thick rendering in CM 1:4 Complete all as specified and directed by Engr-in-Charge.

M&L for coloured non skid ceramic tiles (1st quality), 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for coloured glazed ceramic tiles (1st quality), 450mm x 350mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick screed bed CM 1:6 complete all as specified& directed by Engr-in-Charge.

S&F anodized aluminium frame with power coating (minimum thickness 50 micron) and other sections for doors, windows, ventilators, partitions, with one or more rebates including joining cleat for fixing etc. complete all as specified & as directed.

S&F anodized aluminium door shutters, aluminium section weighing 0.55 kg/m, with power coating (minimum thickness 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc. complete all as specified & as directed.

S&F door closer hydraulically regulated, designation No. 2, aluminium (Die cast) body, universal type (ISI marked) suitable for door shutters of 701 to 850mm in width aand weight between 36 to 60 Kg and fixed complete all as specified & as directed.

S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m,with power coating (minimum thickness 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) complete all as specified & as directed.

Supply only 5mm thick Tinted Coloured glass fixed to metal frame complete all as specified and directed.

Supply only 5mm thick Froasted glass in squares n exc 0.5 sq. m each pane all as specified and directed by Engr-in-Charge

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples & scrwed complete all as specified and directed

S&F anodized aluminium grill with power coating (minimum thickness 50 micron) of approved pattern and fixed to the existing window/ventilator frame with CP brass/stainless steel scrwed @ 200mm center to center, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening all complete as per requirement & directed by Engr-in-Charge.

Supply and fixing Powder coated aluminium sliding window (Bombay sliding Window) made out of hollow extruded aluminium sections as mentioned below and glazed with tinted coloured glass 4 mm thick, fixed with glazing clips, rubber beading/gasket powder coated aluminum beading, screws and lock type handles of size 75 mm, 2 Nos aluminium tower bolts 150 mm long etc complete all as specified and as directed. Shutter top & bottom size : 37.50 x 15 x 1.60 mm thick Shutter inner lock size 37.50 x15 x 1.60 mm Shutter side (handle) size 37.50 x15x1.36 mm Chowkat Bottom : Size 50.30x26x1.20 mm Chowkat top & sides : Size : 50.30x26x1.00 mm

S & F of venation blinds( super quality) to window openings of the following makes-MAC,Sista or equvalent.

S & F IInd class hard wood plain solid straight chowkat and frame wrought framed rebatted on the solid rounded or chamfered put together with glue pinned at joint complete all as specifed

S&F factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified and directed.

S&F factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified and directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam sheet instead of wood grain printed PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded prelam PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of prelam both side PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, stile & rails feathered at edges, suppling & fixing in the frame at site as per specification & drawing.

Supply and fixing stainless steel hinges 100mm long medium weight to pressed steel/angle iron frames by welding/screws all as specified.

S&F aluminium anodised barrel tower bolt 150mm size extruded section, ISI marked & fixed

S&F extruded aluminium alloy handles 150mm size fabricated type anodised. ISI marked.

S&F 300 mm long mild steel sliding door bolts clip type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, ISI marked complete all as specified.

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified.

S&F in repairs powder coated stainless steel drapery rod of 25 mm inner dia (in lengths as directed) of approved colour with & including decorative bowel at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C all as specified & as directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

S&F galvanised steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

S&F galvanised steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I

S&F Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and as directed.

S&F PVC connection 600 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F 15mm bore stop / angle valve, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F 15 mm bore bib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified. Note :- Excavation & earthwork shall be measured & paid for separately.

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified.

S&F 110 mm bore PVC (SWR) single junction (single 'T' ) equal or unequal with access door complete all as specified.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls

S&F 110mm bore PVC (SWR) vent cowl complete all as specified.

S&F PVC (SWR) floor trap plain with PTMT grating including jointing with solvent cement, diameter of outlet 100mm, complete.

S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and including connections to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. complete

S&F PVC valveless, syphonic action type, flushing cistern, low level, white (ISI marked) of 10 litre capacity with inlet, ball valve, float and handle including brackets, flush pipe of polyethylene of low or high density or 32 mm dia PVC pipe, for low level cistern connections to pipes and fixing of chain and pull, or lever, if any complete all as specified..

S&F chromium plated Brass health faucet for EWC with including PVC Connection 1m long suitable for 15mm bore with all connected fittings.as approved by the GE.

S&F Pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore all as specified

S&F 32mm dia Brass chromium plated bottle traps for wash basins/urinals with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed Complete all as specified

S&F urinal size of 14" x 16" x 25 " white(minimum),including CP urinal spreader with CP push cock complete all as specified.

S&F vitreous china counter top basin size 450 x 525 x 195 mm shape oval of Jaquar or equivalent of PARRYWARE / MARC / KINGSTON / SOMANY / ESS ESS / SIECO / KOHLER / HINDWARE / PRAYAG / PARKO including 32 mm CP waste coupling complete all as specified & directed.

S&F glass shelf rectangular type size 600mm x100mm with ss railing complete all as specified & as directed.

S&F stainless steel gratings 100 mm dia with waste hole for floor trap/Nahani trap complete all as specifed and as directed

S&F tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges fixed to wall complete all as specified and directed.

M&L for brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:4 complete all as specified.

Providing and laying for Precast steel fibre Reinforced concrete RCC Soak Well Ring and size of ring 1200mm dia , 600mm height , ring wall 75mm thick complying to the standard specifications as mentioned in the IS 12592 BIS Standard circular shape complete all as specified and directed by Engr-in-Charge.

Providing and laying 100mm thick for precast SFRC drain cover without frame but including complete sides iron sheets (medium ) complying to the standard specifications as mentioned in the IS 12592 BIS Standard minimum load bearing capacity 5 ton /Sqm in square or rectangular shape complete all as specified and directed by Engr-in-Charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified.

Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete all as specified& directed.

M&L Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240 Complete all as specified

M & L preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L Pre- painted galvatume aluminum zinc coating GI based Semi-corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engr-in-Charge.

M&L for false ceiling made out of E-board classic of size 600 x 600 x 4 mm thick, GI frame consisting of main Tee of size 38.50 x 24.00 mm and cross Tee of size 28.50 x 24.00 mm thick made out of PGI sheet 0.30 mm thick doubled at web and single at flange, flange covered with powder coated sheet 0.25 mm thick and angle 24.00 x 24.00 x0.4 mm thick powder coated suspended with GI wire 5mm dia and up to 2 Mtrs long complete including plugging fixing of angle to brick walls with steel rawl plugs @ 450 mm c/c and applying two coats of Oil Bound distemper to the ceiling board complete all as specified and as directed by Engineer-in-Charge.

M&L for Solid PVC Wall Lining/Wall penelling consisting of 5mm thick single side prelam PVC sheet used instead of plain colour sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing

M&L for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing

Supply and fixing mild steel almirah shutters with frame, exceeding 1.5 Square metre, made of 1mm thick mild steel sheet, in two leaves, as built in furniture in cupboards, including locking arrangement with mortice lock of mild steel, vertical type, 65mm size, 2 lever, ISI marked with duplicate keys and handle, etc. (all as per Godrej pattern) including two coats of approved colour synthetic enamel spray painting over a coat of red oxide primer complete fixed in brick or concrete wall with minimum six numbers of 10mm dia and 100mm long mild steel bolt with washer and nut in cement mortar (1:4) or PCC 1:2:4, type B-0, complete all as specified and directed.

Material and labour for point wiring complete with 1.5 sqmm PVC insulated unsheathed 1100 volts grade cable stranded copper conductor single core concealed wiring in medium duty conduit of not less than 20 mm complete with junction box and plate for fitting mounting switch with 1.5 sqmm PVC insulated copper conductor earth wire and connected to earth dolly for one light point controlled by one switch all as specified and directed.

All as per item No.96 Above but One 5 pin, 5 Amps socket out let on same board with 1.5 Sqmm cable & alongwith 1.5 Sqmm continous earth wire of copper conductor concealed in wall in medium duty PVC conduit.

All as per item No.96 Above but One 5 pin, 5 Amps socket out let on independent board with 1.5 Sqmm cable & alongwith 1.5 Sqmm continous earth wire of copper conductor concealed in wall in medium duty PVC conduit.

All as per Item No. 96 above One 15/20 Amps socket out let or for sheet metal enclosure on independent board with 4 sqmm cable alongwith 4 Sqmm continuous earth wire of copper conductor concealed in wall in medium duty PVC conduit.

S&F Switch piano, flush type single pole, one way 5 Amp complete.

S&F Switch piano, flush type single pole, one way 15 Amp complete.

S&F Buzzer, Ding Dong AC. 230 volts, single pole

S&F Bell push, flush type, 5 amp

S&F Socket outlet 3 pin, 15/5 Amp, flush type complete.

S&F Socket outlet 3 pin, 5 Amp, flush type complete.

S&F Ceiling rose, 3 phase/PVC/ polycarbonate, isolated body

Supply & fix PVC body exhaust fans AC single phase 230/ 240 V of size 250 mm sweep with louver for washroom complete with making arrangement for fixing of exhaust fan on steel window and also making good to disturbed surfaces as per matching to existing.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1400 mm sweep. Min air delivery 245 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

Supply and fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fixing LED street light fitting 15 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, connecting wire lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete

S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings including 9 Watt LED lamp complete

S&F Sheet metal encloure DB DD SPN 415 Volts 12 ways double door complete.

M&L for sub main wiring 2 run of size 6 sqmm PVC insulated electric power cable (heavy duty) 1100 volts grade with stranded copper conductor with, 6 sqmm PVC insulated copper conductor earth wire in concealed PVC conduit (2 run of 6 sqmm cable and 1 run of 6 sqmm wire and one run of PVC conduit will be measured as one unit) all as specified and directed.

M&L for sub main wiring 2 run of size 10 sqmm PVC insulated electric power cable (heavy duty) 1100 volts grade with stranded copper conductor with, 10 sqmm PVC insulated copper conductor earth wire in concealed PVC conduit (2 run of 10 sqmm cable and 1 run of 10 sqmm wire and one run of PVC conduit will be measured as one unit) all as specified and directed.

S&F of MCB SP 6-32 Amps,240 Volt B series type complete all as specified and as directed.

S&F of MCB SP 40 Amps,240 Volt B series type complete all as specified and as directed.

S&F of MCB SPN 32 Amps,240 Volt B series type complete all as specified and as directed.

S&F XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sq. mm complete all as specified and directed

S&F MCCB TPN 4 pole 415 volts 100 Amp 16 KA rupturing capacity for fixing in DBs of including proper thimble connections complete all as specified and directed

S&F MCCB TPN 4 ways double door 415 volts with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting type drilling holes for incoming and outgoing cables complete with IP 42 all as specified and directed

Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion

Excavation in trenches not exc 1.5m wide and exc 1.5m in depth but not exc 3.00 mtr depth for laying of cables, errection of poles, struts/stays, levelling of yard etc not exc 10 sqm on plan and getting out , in soft/loose soil compelte all as specified and directed

Material and labour for sand cushioning to cable with layer of sand 8cm deep before laying the cable and 15cm deep after the cable (punned down to 18cms depth after laying and streching of cable) complete all as specified and directed

M&L brick sub class B locally available best quality laid in trenches above sand cushioning for cable protection complete all as specified and directed

S&F tubes, 'light grade',of 40mm dia galvanised, with all fitting; laid in trenches as specified and directed

DHIMAN ENGINEERS & BUILDERS