SPECIAL REPAIR TO BLDG NO T-116, T-117 AND P-245 BC AT FS UNIT INCLUDING SPECIAL REPAIR TO BLDG. NO P-31 BC AND P-33 BC AT SIG COY ALONG WITH SPECIAL REPAIR TO BLDG. NO T-64 BC AT OMC UNIT AND SPECIAL REPAIR TO OR TOILET AND BATHROOM OF BLDG. NO T5B

SCHEDULE 'A' PART-I : BOQ OF WORKS FOR B/R WORKS.

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level), ncluding cleaning, removal and disposal of rubbish/ waste materials from premises, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed.

Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sqm each, complete all as specified and as directed.

Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exceeding 4.0 Sqm each, complete all as specified and as directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified and as directed.

Dismantling timber scantlings 40 Sqcm and over in section, unframed work, in any position, complete all as specified and as directed.

Dismantling water tanks capacity exceeding 500 Litres but not exceeding 1000 Litres and removing to store, complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc, complete all as specified and as directed.

Pre-cast cement concrete block masonry M-10(1:3:6), type C-1 (using 20mm graded crushed stone aggregate) with solid blocks, exceeding 10cm in width and incluing setting in cement mortar 1:6, complete all as specified and as directed.

Rendering 15mm thick on fair faces of on brick work or concrete surfaces, in cement mortar 1:6, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed.

Rendering 15mm thick on fair faces of on brick work or concrete surfaces, in cement mortar 1:4, rendering is to be finished even and smooth (without using extra cement) on external surfaces including mixing water proofing compound @ 200ml per 50 Kg of cement content, complete all as specified and as directed. Note: Water proofing compound shall be measured and paid separately under respective item of BOQ.

Supply only liquid water proofing compound, complete all as specified and as directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion and including over one coat of chalk whiting to prepare the surface even and smooth, complete all as specified and as directed.

Preparation of old/ decorated plastered or unplastered surfaces of walls including washing, rubbing down and stopping of distempered and painted surfaces and applying two coats of distemper oil emulsion, complete all as specified and as directed.

Preparation of new plastered surfaces of walls and applying two coats of cement paint over one coat of priming plastered and other surfaces with alkali resistant priming paintlime wash, complete all as specified and as directed.

Preparation of old/ decorated plastered or unplastered surfaces of walls and applying two coats of cement paint, complete all as specified and as directed.

Plain cement concrete M-15(1:2:4), type B-0 (using 12.50mm graded crushed stone aggregate), nominal mix, 25mm thick, as in floors, finished even and rough to receive floor finishes, complete all as specified and as directed.

Vitrified Ceramic tiles of light shade, 10mm thick (square/ rectangular) polished, non-skid, area of each tiles not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, and including laid over screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6, complete all as specified and as directed.

Vitrified Ceramic tiles of light shade, 10mm thick (square/ rectangular) polished, non-skid, area of each tiles not exceeding 0.36 Sqm, set and fixing in vertical surfaces/ skirting/ dado or any other vertical surfaces and pointed in white or coloured cement to match and including rendering of 10mm thick in cement mortar 1:4 as backing of tiles, complete all as specified and as directed.

Non-skid, coloured, ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 Per Square Metre but not exceeding 0.18 Per Square Metre, in skirting or in vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including fixed over screed bed or bedding layer of mortar 10mm thick in cement mortar 1:4, complete all as specified and as directed.

Glazed ceramic coloored tiles in vertical surface/ dado, size 300x200x6/7mm, 300x450x6/7mm, 350x250x6/7mm, or 450x350x6/7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match, the shade/ colour of tiles including rendering of 10mm thick in cement mortar 1:4 as backing of tiles, complete all as specified and as directed.

Granite (of any type) work (table rubbed and polished), 20mm thick, as in steps, jambs, pillars, window cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, and including laid over screed bed or bedding layer 20mm thick in cement mortar 1:6, complete all as specified and as directed.

Plain cement concrete M-10(1:3:6), type C-1 (using 20mm graded crushed stone aggregate), 75mm thick, as in plinth protection, finish even and smooth without using extra cement, complete all as specified and as directed.

Steel ventilator with top hung shutter including hinges, steel peg stay, complete, complete all as specified and as directed.

Rolled mild steel in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.confirming to Fe 410-W (Gde- E- 250) quality- A, complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating galvanised iron based corrugated steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specifed and directed.

Pre-painted galvalume aluminium zinc coating galvanised iron based plain steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specifed and directed.

Galvanised, corrugated mild steel sheeting 0.63mm thick, with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in lieu of screws, in roofs, walls etc. with grade of zinc coating 275, complete all as specified and as directed.

Factory made steel window, box type, using ERW hollow 'P' section, comprising double frame for and including gauged and glazed skeleton shutter, jointed internally with flat iron 40x4mm complete including grill/ guard bars of 8mm square bars fixed horizontally @100mm C/C including mild steel hinges, handles, tower bolts, stops, lugs etc, complete all as specified and as directed.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290, Gde-E-165, complete all as specified and as directed.

Sheet glass, 3.0mm thick, ordinary quality and glazing with oil putty or with wooden beadings, fixing in square not exceeding 0.50Sqm in each pane, complete all as specified and as directed.

Figured glass, 4.0mm thick, pin head type and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane, fixing in square, complete all as specified and as directed.

Galvanised mild steel wire cloth. 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples, complete all as specified and as directed.

Anodised aluminium snap grid frame work for false ceiling, powder coated, comprising of aluminium Tee (weight of section not less than 280 gms/mtr) and aluminium angle (weight of section not less than 280 gms/mtr), grid size 605x605mm, including Hangers 6.0mm dia, galvanised iron (upto1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of galvanised iron flat 40x3 mm size 60mm long and expansion hold fasteners 12.50mm dia, 40mm long, complete all as specified and as directed.

Providing and fixing everest board 4mm thick, designer, in ceiling fixed as per manufacturer’s instructions, grid size 595x595mm, for false ceiling all as specified, complete all as specified and as directed.

Pressed steel frames for doors of size 125x60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and as directed.

Flush shutters, 35mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete al as specified and as directed.

Glazed and skeleton shutters in second class hardwood, 35 mm thick, divided into square, open rebated and prepared to receive, glass, gauze, etc (with sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc: sizes of members of shutters of window, ventilators,, etc. are provided with stiles and rials as specified in SSR Part-I, Section 8 clause 8.24 (b): supplied and fitted to chowkhats, complete all as specified and as directed.

Solid PVC Door Frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specification and drawing, including making good to disturbed surface of walls, complete all as specified and as directed.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/ sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing in SSR, complete all as specified and as directed.

Preparation of new or previously untreated wood or wooden surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10cm width or girth including and applying two coats of synthetic enamel paint over one coat of zinc chrome/ red oxide primer, complete all as specified and as directed.

Preparation of old painted steel surfaces of any description, over 10cm width or girth including and applying one coat of synthetic enamel paint, complete all as specified and as directed.

Aluminium alloy, anodised, sliding door bolt, size 300mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and as directed.

Aluminium anodised, barrel tower bolts of extruded Section, size 300mm long and fixed, complete all as specified and as directed.

Extruded aluminium alloy handles, fabricated type, anodised, size 150mm, complete all as specified and as directed.

Butt hinges, size 100mm, medium weight, cold rolled mild steel, and fixed, complete all as specified and as directed.

Mild steel, 300mm, ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and as directed.

Rotational moulded polyethylene water storage tanks of 1000 liters capacity, (cylindrical vertical with closed top) with lid, hoisted and fixed in position all as specified in SSR Part-I including ball valves high pressure of PTMT with epoxy coated aluminium rod and highdensity plastic ball screwed for iron pipe and fixed for 20mm bore pipe, fixing in repairs, complete all as specified and as directed.

Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe, complete all as specified and as directed.

Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed for 20mm bore pipe, complete all as specified and as directed.

Vitreous China wash hand basin with pedestal, white, flat back, size 580x450mm including, waste, chain and plug and porcelain stopper including brackets of any size, and including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32mm dia, waste coupling of PTMT (half or full threaded), fixing in repairs, complete all as specified and as directed.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580x440mm white, with integral foot rests (excluding flushing cistern and flush pipe) but including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to dismantled floor in cement concrete M-15 (1:2:4), type B-1 (using 20mm graded crushed stone aggregates), fixing in repair, complete all as specified and as directed.

Vitreous China wash down water closet pan (pedestal pattern), white (including fixing bolts, flush pipe but excluding flushing cistern) and including plastic water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and making good to dismantled/ damaged floor in cement concrete M-15 (1:2:4), type B-1 (using 20mm graded crushed stone aggregates), fixing in repairs, complete all as specified and as directed.

Brass chromium plated basin mixer for mixing hot and cold water screwed down for iron pipe and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed.

PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, capacity 10.0 litres and making good to dismantled/ damaged floor/ surfaces, fixing in repairs, complete all as specified and as directed.

Bib taps, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed.

Brass chromium plated wall mixer for mixing hot and cold water screwed down for iron pipe and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed.

Brass chromium plated shower rose 125mm size, with or without swivel joints, any size, including fixing to steel pipe or union for 15mm bore pipe, complete all as specified and as directed.

PVC connections 15mm size with brass nuts, of length 450mm, metallic wire braided, fixing in repairs, complete all as specified and as directed.

Angle/ Stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed.

Tubular towel rail, 20mm dia, D-type, 60cm long between flanges, brass chromium plated, fancy type, including end brackets, fixing in repairs, complete all as specified and as directed.

Vitreous China Urinal, half stall type, white, with grating and union for discharge pipe (excluding flushing cistern and flush pipe but including of waste pipe), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and union for discharge pipe, fixing in repairs, complete all as specified and as directed.

Sheet glass shelf assembly, consisting 5.0mm thick sheet glass, 250mmx250mm size fixing with chromium plated screws including anti rust screws, fixing in repairs, complete all as specified and as directed.

Grating doom, chromium plated, size 100mm dia, complete all as specified and as directed.

PVC (SWR) pipes, 110mm bore, single socketed, capacity not, less then 4.50 Kgf/Sqcm, in any length fixing with adhesive/ solvent cement, laid in trenches or in floors, complete all as specified and as directed.

PVC (SWR) bends of 110mm bore, pressure capacity not less than 4.50 Kgf/Sqcm, any radius, fixing with adhesive, complete all as specified and as directed.

PVC (SWR) junction single, (Single T) equal or unequal, suitable for 110mm bore pipe, complete all as specified and as directed.

Curtain rod, 20mm dia, mild steel, fancy type, any colour coated with fixing and inlcuing end knobs, fixing brackets, stops, round rings to hold the curtain, fixing with wall plugs and screws, complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition), including cleaning, removal and disposal of rubbish/ waste materials from premises, complete all as specified and as directed.

Dismantaling of brickwork or stone/ boulder masonry, including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles built in cement mortar or cement lime mortar of any description, complete all as specified and as directed.

Taking up or down steel tubing of 15mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed.

Taking up or down steel tubing of 20mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed.

Dismantling water tanks capacity exceeding 250 Litres but not exceeding 500 Litres and removing to store, complete all as specified and directed.

Rotational moulded polyethylene water storage tanks of 500 liters capacity, (cylindrical vertical with closed top) with lid, hoisted and fixed in position all as specified in SSR Part-I including ball valves high pressure of PTMT with epoxy coated aluminium rod and highdensity plastic ball screwed for iron pipe and fixed for 20mm bore pipe, fixing in repairs, complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

Plain cement concrete M-15(1:2:4), type B-2 (using 40mm graded crushed stone aggregate), as mass concrete in foundation filling, complete all as specified and as directed.

Plain cement concrete M-7.50(1:4:8), type D-2 (using 40mm graded crushed stone aggregate), 100mm thick, as in sub base, finish even and smooth without using extra cement, complete all as specified and as directed.

Reinforced cement concrete M-15(1:2:4), type B-1, (using 20mm graded crushed stone aggregate), nominal mix, as in Beams, cantilevers, bressummers, lintels over 1.50mtrs span, including necessary form work, complete all as specified and as directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, including binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified and directed.

Chequered cement concrete coloured tiles, pre-polished, size 300mmx300mmx25mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over 20mm thick screed bed or bedding layer in cement mortar 1:6, complete all as specified and as directed.

Non-skid, coloured, ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.09 Per Square Metre but not exceeding 0.11 Per Square Metre, in skirting or in vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including fixed over screed bed or bedding layer of mortar 10mm thick in cement mortar 1:4, complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating galvanised iron based plain steel sheet 0.80mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specifed and directed.

Preparation of newly plastered or unplastered surfaces of walls and applying three coats of white/ lime washing on prepared surfaces, complete all as specified and as directed.

Powder coated (minimum thickness of powder coating 50 micron), anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc., complete all as specified and as directed.

Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 Kg/Rm including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21 100mm long (2 No.) suitable handle (1 No.), complete all as specified and as directed.

Aluminium alloy, anodised, sliding door bolt, size 250mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and as directed.

Sheet glass, 5.50mm thick, tinted/ reflective, ordinary quality and glazing in aluminium shutter in square exceeding 0.50 Sqm in each pane, in square or any size, complete all as specified and as directed.

Vitreous China wash hand basin, white, flat back, size 550x400mm including, waste, chain and plug and porcelain stopper including brackets of any size, and including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32mm dia, waste coupling of PTMT (half or full threaded), fixing in repairs, complete all as specified and as directed.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed.

Low density polyethylene (LDPE) waste/ flush pipes of 32mm bore, pressure rating 6.0 Kgf/Sqcm), 900mm long, fixing in repairs, complete all as specified and as directed.

PVC connections 15mm size with brass nuts, of length 600mm, metallic wire braided, fixing in repairs, complete all as specified and as directed.

Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, for 15mm bore pipe, fixing in repair, complete all as specified and as directed.

Plastic water closet seat, white/ ivory, closed, for pedestal pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, fixing in repairs, complete all as specified and as directed.

Toilet paper holder with flat recessed type stainless steel, fixing in repairs, complete all as specified and directed.

Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 20mm bore pipe, complete all as specified and as directed.

Taking down shutters of any descriptions and refixing in same opening area exceeding 2.00 Sqm, complete all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded Section, size 150mm long and fixed, complete all as specified and as directed.

Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern, complete all as specified and as directed.

Rendering 15mm thick on fair faces of on brick work or concrete surfaces, in cement mortar 1:4, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed.

Plain cement concrete M-15(1:2:4), type B-0, (using12.50mm graded crushed stone aggregate), nominal mix, as in cills, steps; plinth courses, string courses, lacing courses, copings, kneelers, apex stones, bed plates, including necessary form work, complete all as specified and as directed.

Plain cement concrete M-10(1:3:6), type C-1, (using 20mm graded crushed stone aggregate), nominal mix in surface channels and drains, including necessary form work, complete all as specified and as directed.

Plain cement concrete M-15(1:2:4), type B-0, (using 12.50mm graded crushed stone aggregate), nominal mix in surface channels and drains, including necessary form work, complete all as specified and as directed.

Precast cement concrete M-15(1:2:4), type B-1, (using 20mm graded crushed stone aggregate), nominal mix, as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs and similar articles with plain faces, set in cement mortar 1:4, complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 Cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc., complete all as specified and as directed.

Add or deduct for each 25 mm girth or part thereof over or under 30cm, extra for forming fair finished drain or channel 30 Cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc., complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc, complete all as specified and as directed.

SCHEDULE 'A' PART-II : BOQ OF WORKS FOR E/M WORKS.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc, complete all as specified and as directed.

Description all as serial item No- 118.00 here-in-before but for one 3- pin, 5/ 6-Amps, socket outlet on same board.

Modular switch piano, single pole, one way, 5/ 6 Amps, 1-module, complete all as specified and as directed.

Modular socket outlet, 2-in-1, 3-pin, 5/ 6-Amps, 2-module, complete all as specified and as directed.

Modular switch piano, single pole, one way, 15/ 16 Amps, 1-module, complete all as specified and as directed.

Modular Socket 6Amps/ 16Amps, 2/3-pin combined, 2-module, complete all as specified and as directed.

Modular white cover plate with frame, 3-module including metal flush box, complete all as specified and as directed

Modular white cover plate with frame, 8-module including metal flush box, complete all as specified and as directed

Ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body, size 65mmx25mm dia, complete all as specified and as directed.

LED lights fitting wall surface mounted, 20 Watt, 220 Volt, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and as directed. Make: Havells cat part No- LUMILINEPLUSPROBS20WLED865SPCSSIND or equivalent in Philips/ Bajaj/ Crompton.

LED lights fitting wall surface mounted, 10 Watt, 220 Volt, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and as directed. Make: Havells cat part No- LUMILINEPLUSNEOBS10WLED865SPCSSINDS or equivalent in Philips/ Bajaj/ Crompton.

Sheet metal enclosures for Single Pole and Neutral distribution boxes with double door glazed for incorporating MCBs, IP-65, 4-way with 200 amps rated busbar, 240 volts, as per IS-8623, fixing in repairs, complete all as specified and as directed.

LED street light fitting 35 Watt 230 Volt, AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed. Make: Havells cat part No- Superb Street Light 30 W 6500 K IP65 or equivalent in Phillips/ Bajaj/ Crompton.

House service bracket, made with 2.50mtr long galvanised iron pipe 25mm dia medium grade, 120° bends including mild steel clamps of mild steel flat 50x6mm, hook, stay, nut, bolt and washer including painting with two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed.

MCB, double pole and neutral, 32 Amps, 240 volts, 50 Hz, 'C' curve including necessary incoming and out going electric connection with suitable size of copper lugs, fixing in repairs, complete all as specified and as directed.

MCB, single pole, 6 to 32 Amps, 240 Volts, 50 Hz, 'C' curve including necessary incoming and out going electric connection with suitable size of copper lugs, fixing in repairs, complete all as specified and as directed.

Supplying and fixing in replacement of 1100 volts grade heavy duty cable PVC insulated stranded aluminium conductor of 10.0 Sqmm, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1.0metre apart including 4.0mm suspension wire, one twin core cable flat or circular, complete all as specified and directed.

Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, having Copper winding motor with sweep 150mm, complete all as specified and as directed. Make: Havells ordering code- FHVVEBLWHT06/ Bajaj cat part No- AirOut 150mm or equivalent in Philips/ Orient/ Crompton/ Usha.

Lamp holder, PVC Polycarbonate type with back plate suitable for batten fittings, complete all as specified and as directed.

LED lamp, capacity 9 Watt, B-22 holder base with ploycarbonate body and aluminium heat sink, warm/ white light, fixing in repairs, complete all as specified and as directed. Make: Havells ordering code- LHLDDDBEBI2R009 and cat part No- LED ADORE PLUS 9 W B22 WW 2 STAR LAMP or equivalent in Philips/ Bajaj/ Crompton.

Earthing complete with galvanised iron earth plate electrode 600x600x6mm buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of earth plate not less than 1.5mtr below normal ground level, connected with galvanised iron wire, size 4.0mm dia as earth lead, by means of bolts, nuts, check nuts and washers of galvanized iron or steel complete with 20mm dia GI light grade protection pipe, 20mm dia GI medium grade watering pipe with funnel including charcoal, dust, salt, PCC M-15, type B-1 in pit with precast RCC M-15(1:2:4), type B-1 (using 20mm graded crushed stone aggregates) in cover reinforced with XPM not less than 4.0 Kg per Sqm, test point etc. all as shown in electric plate No-3 of SSR Part-I (2009), complete with necessary earth work in any type of soil, removal to a distance not exceeding 50mtr, including testing on completion, complete all as specified and as directed by Engineer-In-Charge. Note: Earth pit chamber and RCC pit cover shall be painted with two coats of red synthetic enamel paint over one coat of primer including preparing of surfaces.

Exhaust fan made of metallic body including metallic sweep complete, voltage 230V, 50 Hz, RPM 1200, having Copper winding motor with sweep 300mm, complete all as specified and as directed. Make: Havells ordering code- FHEHDSPDB120/ Bajaj cat part No- Maxima Neo 300 or equivalent in Philips/ Orient/ Crompton/ Usha.

Water heater storage type (geyser), wall hanging, steel body with heavey duty inner tank and heating element upto 2 KW capacity 25 litre, BEE 5-Star rated, single-phase, 50 Hz AC, energy saving high density PUF insulation, including all accessories such as safety valve, thermostate, NRV, fixing in repairs, complete all as specified. Make: Havells cat part No- GHWACATWH025 or as equivalent in Bajaj/ Jaquar/ Crompton.

Amount of Schedule of credit as mentioned here-in-after shall be deducted from quoted amount.

Please Enable Macros to View BoQ information