Loading…
Loading…
Tender Value
₹6.3 Cr
EMD Value
₹6.3 L
Closing Date
13 Jul 2026, 6:00 pm
Similar tender results from the same govt authority in the past 3 years.
add.city.engineer (amc met/Hospital, East Zone)
EXTENSION OF COMMUNITY HEALTH CENTRE OPP. R.T. SCHOOL, VASTRAL, EAST ZONE, AHMEDABAD. ( REINVITE)
318672
EZ 02/12/2026-27
Open
Miscellaneous Works
Ahmedabad
3 documents required · 3 mandatory
₹12,000
Municipal Commissioner, Ahmedabad
₹6.3 L
29 Jun 2026
29 Jun 2026
29 Jun 2026
13 Jul 2026
29 Jun 2026
PRICE BID - BILL OF QUANTITIES (B.O.Q.)
Name of Work : TENDER DOCUMENT FOR EXTENSION OF
COMMUNITY HEALTH CENTRE OPP. R.T. SCHOOL,
VASTRAL, EAST ZONE, AHMEDABAD.
Name of Contractor : M/s. __________________________
Correspondence Address :
Tender Amount : Rs.
(Rs. Six Crores Thirty Lacs Fifty Five Thousand One Hundred and Thirty Three and Twenty Eight Paisa
Contractor’s Quoted Rate: -
Seal and Signature of the Bidder Additional City Engineer (East Zone)
Date: Ahmedabad Municipal Corporation
PLEASE NOTE : PLEASE DO NOT FILL PRICE BID IN HARD COPY.
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
EXTENSION OF COMMUNITY HEALTH CENTRE OPP. R.T. SCHOOL, VASTRAL,
EAST ZONE, AHMEDABAD.
SR. NO. ITEM DESCRIPTION AMOUNT
A CIVIL WORKS 4,65,58,800 =56
B PERCOLATING WELL 3,99,106=82
C LANDSCAPE 8,13,500=00
D PERCOLATING WELL 9,28,377=00
E ELECTRIFICATION WORKS 1,14,63,144=35
FIRE DETECTION, ALARM AND HYDRANT WORKS 28,92,205=55
(Rs. Six Crores Thirty Lacs Fifty Five Thousand One Hundred Thirty-Three and Twenty-Eight Paisa
Seal and Signature of the Bidder Additional City Engineer (East Zone)
Date: Ahmedabad Municipal Corporation
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
EXTENSION OF COMMUNITY HEALTH CENTRE OPP. R.T. SCHOOL,
VASTRAL, EAST ZONE, AHMEDABAD.
Item Tot. Qty. Unit Rate Amount
Brick Masonary Demolition : Demolition and
disposal of unserviceable materials with all
leads and lifts for plastered Brick masonary.
Rate also includes necessary tools,
scaffoldings and all safety measures required
for the same, including all leads and lifts.
RCC Demolition : Demolition and disposal of
unserviceable materials with all leads and
lifts for plastered RCC work.Rate also
includes necessary tools, scaffoldings and all
safety measures required for the same,
including all leads and lifts. This includes
cutting of reinforcement steel and shifting it
to ground from any height and level.
Dismantling Old Plaster: Removing and
scraping of old deteriorated plaster of any
3 thickness from Wall / RCC member including 925.00 Smt. 19.38
stacking of unserviceable material from site
of work with all leads and lifts.
Dismantling Flooring : Dimantling tiled or
stone floors or tiles laid in mortar including
4 stacking of serviceable materials and 1515.00 Smt. 47.25
disposal of unserviceable materials including
all leads and lifts.
Dismantling Doors etc. : Dismantling any
type (aluminum/ wooden etc.) doors,
windows , ventilators etc. (wood / aluminum
5 or steel grills) shutters including chowkhats,
architraves, holdfasts and other attachment
etc. complete and stackign the materials with
all lead and lift.
a) Not exceeding 3 Smt. In area 15.00 Nos. 185.85
Dismantling Pipes: Dismantling G.I. , PVC, C.I.
pipes, GSW pipes and A.C. rain water pipes
6 with fittings and clamps including stackign 500.00 Rmt. 74.03
the materials with all lead and lift (For any
diameter of pipe, from wall and floors etc.).
Dismantling Sanitary Fittings : Dismantling
sanitary fitting like wash basin, WC pan
7 indian and europena type , flusing tank etc. 10.00 Nos. 401.63
including stacking the materials with all lead
and lift etc. complete.
Dismantling Fabrication works : Dismantling
8 steel work including dismembering and 2000.00 Kgs. 3.63
stacking the materials with all lead and lift.
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
This includes removal polycarbonate sheet
with proper safety and system.
Dismentaling of sheet roofing including
ridges, Hips, Valleys, Gutters etc. stacking of
serviceable materials and disposal of
unserviceable materials with all lead and lift.
Labour work for fixing Interlocking Blocks /
any kind of pavement on up to 50 mm thick
10 sand bedding, levelling, watering and fixing 500.00 Smt. 68.64
in line & level as well cleaning the site
etc.comp. as directed.
Excavation Upto 1.50 Mt.: Excavation for
foundation upto 1.50 Mt depth including
11 sorting out and stacking useful materials and 200.00 Cmt. 115.92
disposing off the excavated stuff upto
Meters lead (B) Dense or hard soil.
Excavation From 1.50 Mt. to
Mt.:Excavation for foundation 1.50 Mt to
Mt. depth including sorting out and stacking
useful materials and disposing off the
excavated stuff upto 50 Meters lead (B)
Dense or hard soil.
Excavation for foundation 3.0 Mt. to
Mts.: Excavation for foundation 3.0 Mt. to
5.00 Mts. depth including sorting out and
stacking useful materials and disposing off
the excavated stuff upto 50 Meters lead (B)
Dense or hard soil.
Excavation for additional depth more than
5.00 Mts:Excavation for additional depth
more than 5.00 Mts. For excavation for
14 foundation including sorting out and 50.00 Cmt. 162.02
stacking useful materials and disposing off
the excavated stuff upto 50 mt. Lead. (B)
Dense or Hard Soil.
Add extra for Disposing off the excavated
15 stuff of above items for lead of (A) 50 m to 100.00 Cmt. 17.28
Add extra for Disposing off the excavated
16 stuff of above items for lead of (B) 100 m to 100.00 Cmt. 34.56
Providing and installing cast in situ single
under reamed piles of specified diameter and
length below pile cap, excluding the cost of
Concrete, steel reinforcement but including
the cost of boring with bentonite solution
and the length of the pile to be embedded in
pile cap etc. all complete.Reinforcement shall
be measured seprately and be paid extra.
(Length of pile for payment shall be
measured upto to the bottom of pile cap) :
(a) 400 mm dia. Piles 5.00 Rmt. 638.83
(b) 450 mm dia. Piles 5.00 Rmt. 705.03
Extra over single under ream for providing
additional bulbs in under reamed piles,
18 under specified diameter excluding the cost
of Concrete, steel reinforcement (only the
nos. of extra bulbs are to be paid).
(a) 400 mm dia. Piles 5.00 Nos. 813.05
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
(b) 450 mm dia. Piles 5.00 Nos. 1103.43
Filling available excavated earth: Filling
available excavated earth (excluding rock) in
trenches, plinth, sides of foundations etc. in
19 layers not exceeding 20 cm. in depth, 100.00 Cmt. 129.10
consolidating and compacting each
deposited layer by ramming and watering
Filling Murrum : Filling in foundation and
plinth with murrum or selected soil in layers
of 20 cm. thickness including watering,
ramming and consolidating etc. complete.
Sand filling: Sand filling with sand as
approved by Architect in plinth / under floor
/ else where including watering, ramming,
21 consolidating and dressing to the required 10.00 Cmt. 455.63
grades and levels as directed by Engineer-in
charge. Proper care shall be taken for sieving
the sand before use.
Lightweight filling :Filling in Sunken Portion
with good Quality Aerated light weight
concrete block having crushing strength not
less than 35 kg/sqcm and where directed by
the Architect / Engineer-in-charge, in sunk in
layer. including watering, ramming where it
is required etc. complete, as directed by the
Architect / Engineer-in-charge .
Anti-Termite Treatment : Carring out plinth
treat ment to post construction/ existing
structure by spraying chemical solution for
termite control treatment including labour
and material consist ment withI.S.I
specification. Using Chlordene and Chiorpur
files 20EC. As Per 6131_ paret- II
Consentration Weight one percent is
recommended i.e one litre 20EC chemical
emulsion with19 liter give1% concrentration
inclusive of one litre chemical emulsion
appication at the rate of 5 Litre chemical/
Sqm of surface is recommended as per I.S
Conveyance: Conveyance charges of earth,
lime, murrum, building rubbish, manure,
24 garbage, sludge, excavated rock, fly ash,
aggregate of any kind etc. complete. No dry
factor for this item shall be calculated.
(a) Conveyance charges upto 1 km 500.00 Cmt. 46.63
(b) Conveyance charges upto 2 km 100.00 Cmt. 60.69
(c) Conveyance charges upto 5 km 100.00 Cmt. 100.44
(d) Conveyance charges upto 6 km 100.00 Cmt. 109.70
(e) Conveyance charges upto 7 km 100.00 Cmt. 118.96
(f) Conveyance charges Above 7 km 100.00 Cmt. 128.22
BBCC in 1:4:8: Providing and laying cement
concrete 1:4:8 (1-
Cement : 4- Coarse sand : 8- Graded Brick
bats aggregate 40mm normal size) and
curing complete excluding cost of formwork
in (A) Foundation,plinth and terrace level.
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
PCC in 1:4:8: Providing and laying cement
concrete 1:4:8 (1- Cement : 4 - Coarse
aggregate : 8-Hand broken stone aggregates
40 mm nominal size) and curing complete
excluding formwork in (A)Foundation,plinth
and terrace level.
PCC in 1:3:6: Providing and laying cement
concrete 1:3:6 (1- Cement : 3 - Coarse
aggregate : 6-Hand broken stone aggregates
40 mm nominal size) and curing complete
excluding formwork in (A) Foundation and
RCC M-150: Providing and laying controlled
cement concrete M-150 for curing complete
excluding cost of formwork and
28 reinforcement for reinforced concrete work 95.00 Cmt. 4129.42
in (C) Slabs, landing, shelves, balconies,
lintels, beams, girders and cantilever at any
level and height.
RCC M-200 : Providing and laying controlled
cement concrete M-200 for curing complete
29 excluding cost of formwork and
reinforcement for reinforced concrete work
(A) Foundations, footings, base of columns,
and mass concrete.
(B) Walls at any level and height. 2.00 Cmt. 4484.17
(C) Slabs, landing, shelves,
Balconies,Weather sheds, lintels,beams,
girders, and cantilevers, at any level and
(D) Columns, pillars, posts, and struts, at any
level and height.
(E) Staircase at any level and height. 20.00 Cmt. 5418.91
(K) Vertical and horizontal fins at any level
RCC M-250 : Providing and laying controlled
cement concrete M-250 for curing complete
30 excluding cost of formwork and
reinforcement for reinforced concrete work
(A) Foundations, footings, base of columns,
and mass concrete.
(B) Walls from at any level and height. 71.00 Cmt. 4519.88
(C) Slabs, landing, shelves,
Balconies,Weather sheds, lintels,beams,
girders, and cantilevers, at any level and
(D) Columns, pillars, posts, and struts, at any
level and height.
Reinforcement : Providing T.M.T Fe 500D bar
reinforcement for R.C.C. work including
bending, binding and placing in position
complete up to any floor level
Formwork : Providing Formwork of ordinary
timber planking so as to give a rough finish
including centering, shuttering, strutting and
proping etc. Height of propping and
centering below supporting floor to ceiling
not exceeding 4 Mt. and removal of the same
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
for in -situ reinforced concrete and plain
concrete work in
(A) Foundations footings, bases of columns
etc. and mass concrete.
(B) Flat surfaces such as soffits of slabs,
landings and like(1) Floor etc. upto 200 mm 2675.00 Smt. 252.00
(C) Vertical faces such as walls (any
thickness and at any height) for lift and other 675.00 Smt. 229.95
(G) Columns,pillars, posts and struts (1)
Square, rectangular, polygonal in plan ( For 875.00 Smt. 297.68
"L" Plates only).
(H) Columns,pillars, posts and struts (2)
Circular or curved in plan.
(I) Sides and soffits of beam, haunchings
cantilevers, girders, bracings,and lintels not 2000.00 Smt. 192.15
exceeding 1.0 Mts. in depth.
(L) Chullah, hoods, weather sheds, chhajjas,
corbels, etc. including edges.
(M) Staircases with slopping or stepped
soffits including risers & Strings excluding 220.00 Smt. 242.55
For More Height:For height of propping and
centering where the height of propping and
centering exceeds normal height between
two ceiling including temporary brick or
stone pillars for supporting as required.
(i)Height from 4.00 to 5.0 Mt.
For More Height:For height of propping and
centering where the height of propping and
centering exceeds 4.0 Mts. between
34 supporting floor two ceiling including 50.00 Smt. 682.01
temporary brick or stone pillars for
supporting as required. (ii)Height more than
5.0 Mt and upto 6.0 Mt.
Rebarring:Drilling suitable holes in
reinforced or plain cement concrete with
power driven drill machine to a minimum
depth of 80mm upto 250mm in RCC beams,
lintels, columns and slabs to introduce steel
35 bars for sunshades/balconies including
fixing the steel bars in position using Hilti
Chemical HY200-R or Fischer - FIS 360 or
equivalent but excluding the cost of
reinforcement, all complete as per direction
of Engineer-In-Charge.
(a) 8 mm Dia in 80 mm Deep & 12 mm Dia
(b)10 mm Dia in 100 mm Deep & 14 mm Dia
(c)12 mm Dia in 120 mm Deep & 16 mm Dia
(d)16 mm Dia in 160 mm Deep & 20 mm Dia
(e)20 mm Dia in 200 mm Deep & 25 mm Dia
(f)25 mm Dia in 250 mm Deep & 32 mm Dia
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Tremix: Providing & Applying Tremix
method (Vaccum de extracted & Powered
trowelled ) for Concrete Flooring with
36 necessary finishing either smooth or wire 1700.00 Smt. 54.00
finish as approved by consultants. Rate shall
includes the rate of side shuttering with
channel , rails to form panels etc. complete.
Making 15 mm Groove in R.C.C work on road
and filling it with poly sulfied selant and
finished it good incl. all labour charges etc.
comp. as directed
Providing and laying and fixing 25 mm thick
expansion joint by hydrocell semi rigid UV
38 resistance with high performance laminated 100.00 Smt. 738.13
closed cell polythene foam joint filler in sheet
foam as directed, etc. complete.
Brickwork in Foundation:Brickwork using
common burnt clay building bricks having
crushing strength not less than 35 kg/Sq. cm.
in foundations and plinth in cement mortar
1:6 (1 cement :6 fine sand) for conventional
Brickwork in Super Structure:Brick work
using common burnt clay building bricks
having crushing strength not less than
kg/Sq. cm. in cement mortar 1:6 (1 cement
:6 fine sand) for superstructure upto floor
three level height. For conventional type
bricks. (a) For Superstructure above plinth
level upto floor two level (B) Conventional.
Brickwork in Super Structure:Brick work in
41 super structure above floor two level in 415.00 Cmt. 4293.55
superstructure (B) Conventional.
Half Brick masonary: Half Brick masonary in
common burnt clay building bricks having
crushing strength not less than 35 Kg/Sq. Cm
42 in Cement Mortar 1:4 (1-Cement : 4- Coarse 485.00 Smt. 646.70
Sand) in superstructure above plinth level
for any level and height. (B) Conventional
Fabrication works:Providing, supplying,
fabricating and erecting in position the
structural steel for colums, grill, bars, truss,
purlins, runners, cleats, insert plate, base
plate etc for all structural elements as per
detail, made up from closed structural steel
hollow sections (RHS/SHS including rolled
section) as per IS 4923 of grade Yst 310 mpa
- weather resistant sections or an approved
equivalent as per details /
drawings/instructions including cutting,
bending, jointing, connecting, welding and /
bolting and / riveting and fabricating and
erecting in position etc complete for all levels
as directed. The rate to include all necessary
fixtures, fastening including welding rods of
standard approvded quality etc for complete
the job. The rate shall also include one coat of
an anti-corrosive paint.& necessary
scaffolding etc. complete as directed.
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Providing and fixing in position collapsible
steel shutters with vertical channels 20 x
x 2 mm braced with flat iron diagonals 20 x
mm size with top & bottom rails of T- iron
x 40 x 6 mm with 38 mm dia. Steel pulleys
complete with bolts , nuts , locking
arrangement , stoppers , handles including
applying a priming coat of red lead paint.
Providing, Fabricating and Erecting in
position Partly Panelled Partly Glazed / Fully
Panelled / Fully Glazed anodised (15 to
micron of desired colour) Single Shutter,
Double Shutter, Double door shutter (double
action opening) of standard aluminum
section from 18 mm (3/4”) series of Jindal,
Hindalco, Domel or approved equivalent
make of size as described below or of better
/ higher series if required as per site
condition-top and vertical style 47.62 x
x 2mm (Wt. approx = 1.05 kg./m), lock rail
and bottom section 114.30 x 44.45 x 2 mm (
Wt. approx = 1.83 kg/m), fitted on frame of
size 101.60 x 44.45 x 2 mm ( wt. app =
kg./m) with standard accesories like handle
stopper, locking arrangement, C.P. brass
hinges, etc, and glazing of 5 mm thick float
glass of approved brand, fixed with rubber /
PVC beading in upper / Lower and 12 MM
both side pre laminated sheet fixed with
Glazing clips in Upper / lower panel etc.
complete as per architecture detail given by
the consultants. The same item can be
operated for fixed partitions as and when
needed. All Accessories like aldropt, stopper,
door stop, door magnet and hinges shall be of
Stainless Steel Heavy Duty.
Providing and fixing double action hydraulic
floor spring of approved brand and
manufacture conforming to IS : 6315, having
brand logo embossed on the body / plate
with double spring mechanism and door
weight upto 125 kg, for doors, including cost
of cutting floors, embedding in floors as
required and making good the same
matching to the existing floor finishing and
cover plates with brass pivot and single piece
M.S. sheet outer box with slide plate etc.
complete as per the direction of Engineer-in-
charge. With stainless steel
cover plate minimum 1.25 mm thickness.
Approved Brands : Godrej / Everite or
approved equivalent as directed.
Providing & Fixing Alumnium Doors shutters
using Heavy Aluminum anodised section of
Size 85 mm x 45 mm and respective heavy
frame. Rates also includes Providing and
47 fixing 4 heavy Hinges, 1 Lock, 2 American 130.00 Smt. 4950.00
handles (8" size), 4 mm thick Ginja/ or
approved pattern glass, and 5 mm thick
Compact Sheet (of approved pattern) Upto
Lock Rail height, also includes providing
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
wooden log in top rail for fixing Door Closer.
The wooden log shall be of size to fit into the
frame but 900 mm in length. Half Particle
Board (12 mm thick both side prelaminated)
and Half Glased Doors and / or Full size
Particle Board Doors same rates shall be
Providing and fixing window having
extruded aluminum Colour Powder Coated
section frame main outer size 95mm x 24mm
x 1.17mm @ wt.of 0.738 Kg/mt, horizontal
Two / Three track member size 92mm x
vertical member of size 92mm x 31.75mm x
1.50mm ,@ Wt. 1.06 Kg/mt with sliding
shutters of horizontal member size
mmx18mm x1.29mm @ wt.of 0.456 Kg/mt,
vertical member of size 40mm x 18mm x
mm @ wt.of 0.456Kg/mt with 5 mm thick
transparent bronze colour tinted float glass
with powder coated aluminum fittings and
fixtures and transparent silicon sealant glass
fixing to frame as per details etc. complete.
Providing and fixing standared extruded of
alluminium section of size 63.50 x 38.10 x
1.95 mm @ Wt 1.094Kg / Rmt with colour
Powder Coated alluminium frame with 5 mm
thick transparent bronze colour tinted float
glass with colour anodized alluminium frame
for ventilation with 5 mm thick frosted glass
as details etc complete.
Providing and fixing 32 mm thick water
proof flush doors, rate also includes 12 x
cms Indian teak wood (pure saag) frame and
including fixing of 1.00 mm thick laminate
sheets (Door Skin) on both sides of the doors
, border pattis of C.P. Saag on thickness of the
doors on all four sides, polishing the same
and fixtures fasteners complete as directed.
The rates shall be inclusive of Melamine
polish on all exposed surfaces as per sample
approved by the Consultants, Hardware
Includes 4 nos. heavy chrom plated Hinges,
S.S. Tower bolt (10"), Aldropt Set (10")
Taadi (10"), Door Stop / Door Magnet etc
complete as directed by the Consultants.
Providing and fixing of approved make
radiation-proof lead line door with
galvanised steel. Recommended lead door
design should be a sandwich-type panel with
both sides GI Sheet with a minimum 2mm
Lead infill. Doors should be finished in
Powder Coating with thickness of 60 microns
approx. in desired Shades. The manufacturer
company must be ISO 9001- 2015 certified.
The door frame is a Single rebate profile of
minimum size 105mm X 57 mm made out of
1.2 mm minimum thick galvanized steel
sheet & with 2mm lead infill. The frame is
finished with Powder Coating in desired
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Shade. Frame having provisions and
necessary Arrangement for receiving
appropriate hardware like lock and hinges.
The door leaf shall be a minimum 46mm
thick fully flush double skin door without
vision lite. The door leaf shall be
manufactured from 1.0 mm thick galvanised
steel sheet. Door Includes SS 304 Hinges, D
type Pull Handle-SS 304, Mortise Deadlock
with cylinder - 70mm both side key , Flush
type tower bolt, Door Seal , Door Closer etc.
Complete as per Standard
Providing and fixing FRP frame size 100 mm
x 50 mm and 28mm thick FRP depress panel
shutter having extra reinforcement on sides
& edges in Gel coat finish. The core of the
shutter & frame is to be filed up with injected
fire retardant grade polyurethene foam done
in situ alongwith embedded wooden pieces
for stiffening & also taking hinges & fintures.
The whole FRP frame & shutter is to be water
proof weather proof, termite proof &
resistance to mild acid/alkali. Rates are to be
inclusive of S.S hinges with necessary screws
& alluminium fixtures & fastenings &
fastener sleeve.
Providing 15 mm thick cement plaster in
single coat on Rough (Similar) on brick walls
for interior plastering and finished even and
smooth in (ii) Cement Mortar 1: 4 (1 Cement
: 4 Sand). This includes finishing with a
floating coat of neat slurry and doing plaster
after making thaiyaas / levellers and after
approval from engineer in charge.
Providing 15 mm thick cement plaster in
single coat on ceilings and soffits of stairs and
finished even and smooth in (ii) Cement
Mortar 1: 4 (1 Cement : 4 Sand). This includes
finishing with a floating coat of neat slurry
and doing plaster after making thaiyaas /
levellers and after approval from engineer in
Providing 20 mm thick double coat mala /
sandface cement plaster on brick/ concrete
work for plastering comprising of base coat
of 12 mm thick cement plaster in cement
55 mortar (1 Cement : 4 Coarse Sand) in rough 1750.00 Smt. 297.68
finishing and 8 mm thick top coat of cement
mortar 1:2 (1 Cement : 2 Coarse Sand)
finished with trowel including scaffolding
curing etc. complete.
Providing and laying polished Kota stone
slab flooring over 20 mm (Average) thick
base of cement mortar 1:6 (1-cement : 6-
56 coarse sand) or L.M. 1.1.5 laid over and 20.00 Smt. 982.83
jointed with grey cement slurry including
rubbing and polishing etc. complete. (A)
Providing and laying polished kota stone slab
25 mm thick in risers of steps, skirting dedo
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
and pillars laid on 10 mm thick cement
mortar 1:3 (1 Cement : 3 Coarse sand) and
jointed with gray cement slurry mixed with
pigment to match the shade of slab including
rubbing and polishing etc. complete.
Providing & laying full body, 8 to 10 mm
Vitrified Tiles tiles 800 x 800 mm , 900 x
Nitco/Kajaria/Simpolo/Sunheart/ Asian
Bonzer or equivalent but approved make and
sample approved by architect, approved
colour and shade, any type, in desired
pattern in floor areas with residue, skirting,
pattas as per drawing and specification in
white cement slurry over a minimum 40 mm
thick cement sand mortar (1:6) bedding
screed laid to proper gradient. Rate shall be
inclusive of necessary cutting, joint filling
curing, cleaning with mild oxalic acid etc.
complete for all floors, all levels, all height all
complete as per drawing, specifications,
instruction & directions of the Engineer-in-
charge. The rate should be inclusive of
protection of flooring until the handling of
the project by covering the joints with
abrotaps, plastic sheet or Plaster of paris.
Skirting shall be paid in Square meter.
Payment shall be done as per drawing/laid at
site, The rate shall include cost of fixing
protection sheet and keeping the same intact
untill the handover. Rates also includes
removing the damaged tiles upto the
handover, and removing the protection sheet
at the time of innauguration. Payment shall
be done as per drawing/laid at site. Rates
includes filling 5 mm groove with epoxy
grout of approved shade and brand.
Providing and fixing 6 mm thick approved
quality, colour, design, size and shade matt /
anti skid Ceramic tiles flooring laid over
required bedding (minimum 20 mm
thick)thickness of cement mortar in mix ratio
1:6 (1 cement : 6 sand) in pattern as per the
Project Consultantsural drawing or as
directed by the Project Consultants &
Engineer-in-charge. Tiles fixed to correct
line, level, slopes joints well cleaned, grouted
with matching colour cement paste, cured,
etc. all complete at all height and lead etc.,
complete to entire satisfaction of the Project
Consultants & Engineer-in-charge.Care to be
taken to ensure joints are well grouted,
cleaned and water tight.Any size of tiles may
Providing and fixing coloured glased tiles of
the size 300 mm x 200 mm x 8 mm / 300 mm
x 450 mm x 8 mm / 600 x 300 x 8 mm in walls
skirting, risers of steps and dedo on 10 mm
thick cement plaster in 1:3 (1 Cement :
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Coarse sand) & jointed with white cement
slurry with approved shade of colour to
match the tiles.
Providing and fixing Granite stone (For sills,
jambs, dado, skirting etc.) as approved by the
consultants for steps , sill and jambs of
average thickness 18 m.m. Rate includes
necesssary plaster 12 m.m. thickness in C.M.
1:4 and labour required for fixing in good line
and level etc. comp. The hidden side of the
granite shall be made rough by applying
Areldite of Approved glue and sprinkling
coarse sand on top of it. Later after drying
the stone shall be fixed with screws of
enough length so as to fix the stone properly
in to the wall or the supports. Rate also
includes necessary on-site polishing,
rubbing, moulding the visible edges, cleaning
etc. complete as per the consultants
instructions. No extra rates shall be paid for
any item related to this.
Providing and Laying of Rubber Moulded
Paver Block Grey/Coloured 60 mm thick, M-
35 Grade of any size ; shape (Preferrably
Square shape of size 8" x 8" of as approved by
the consultants and AMC) using black trap
good quality aggragate of 20 mm nominal
size for footpath, parking areas, service lanes
and other areas as mentioned in the drawing
/ instruction of engineer in charge. Cost
includes formworks using rubber mould,
Rate providing and laying paver blocks as per
required grading and specification. The
paver block shall be mechanically
compacted. The work of paving blocks shall
be executed in line and level by skill mason of
flooring work only. It should be laid in such a
way that the no cutting of the paver block to
be necessary. if cutting of paver block
necessary then it should be cut by machine
only and carting. The finished surface of the
paver block shall have resonably good, plain
finished. Paver blocks shall be compacted
and shall be relaid if necessary. Gravel or
such type of materials shall not be allowed
for production. Laying on 5 cms thick sand
Providing and fixing pre-cast concrete kerb
stone of gray cement based concrete block
cm length x 30 cm heigh and 15 cms thick of
63 M-250 grade concrete as per approved 1000.00 Rmt. 358.06
design and including excavation for fixing in
proper line and level, filling the joints in C: M
1:3 (1 Cement : 3 Fine sand) etc. complete.
Providing and laying cement concrete
flooring 1:2:4 (1 Cement : 2 Sand : 4 graded
64 stone aggregates 20 mm nominal size) laid in 1300.00 Smt. 348.08
one layer and finished with a floating coat of
neat cement (A) 50 mm thick.
Providing and laying integral cement based
water proofing treatment including
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
preparation of surface as required for
treatment of roofs, balconies, terraces etc.
consisting of following procedure: (1)
Applying a slurry coat of neat cement using
2.75 kg/sqm of cement admixed with water
proofing compound conforming to IS.
and approved by Engineer-in-charge over
the RCC slab including adjoining walls upto
300 mm height including cleaning the
surface before treatment. (2) Laying brick
bats with mortar using broken bricks/brick
bats 25 mm to 115 mm size with 50% of
cement mortar 1:5 (1 cement : 5 coarse sand)
admixed with water proofing compound
conforming to IS : 2645 and approved by
Engineer-in-charge over 20 mm thick layer
of cement mortar of mix 1:5 (1 cement :5
coarse sand ) admixed with water proofing
compound conforming to IS : 2645 and
approved by Engineer-in- charge to required
slope and treating similarly the adjoining
walls upto 300 mm height including
rounding of junctions of walls and slabs. (3)
After two days of proper curing applying a
second coat of cement slurry using 2.75 kg/
sqm of cement admixed with water proofing
compound conforming to IS : 2645 and
approved by Engineerin- charge. (4)
Finishing the surface with 20 mm thick
jointless cement mortar of mix 1:4 (1 cement
:4 coarse sand) admixed with water proofing
compound conforming to IS : 2645 and
approved by Engineerin- charge (5) The
whole terrace so finished shall be flooded
with water for a minimum period of two
weeks for curing and for final test.“All above
operations to be done in order and as
directed and specified by the Engineer-in-
Charge :and shall be guaranteed for
minimum period of 10 years after handing
over the completed building by the main
contractor to be finished as directed. Official
Guarantee Bond for 10 years on Stamp paper
must be furnished to the client before
receiving any payment.
Providing & laying broken white and/or
coloured glazed china mosaic flooring for
plain and curved surfaces, comprising of
to 20 mm. size broken pieces of glazed tiles,
laid over cement mortar 1:3 bedding, on
plain or sloped surfaces. The flooring shall be
tampered to bring the mortar cream up to
the surface, including rounding of the
junctions and extending them up to 15 cm.
along the parapet wall. The rate shall include
bands, if different colour is used, any
pattern or design as per drawing and
direction, curing, cleaning with water and
oxalic acid, etc. complete. Bands and pattas
shall be paid in Smt. Only.
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Granite Stone :
Providing and laying of approved quality
mirror polished 20 mm thick Granite stone (
Any colour ) flooring laid in pattern (as
detailed by the Consultants) bedded over
average 20-25 mm thick cement mortar, mix
ratio 1:6 (1 cement : 6 sand) laid to slopes as
detailed in drawing, including cleaning and
67 preparing the surface for bedding, curing of 50.00 Smt. 2385.71
bedding screed etc. Joint width to be as
specified by the Engineer-in-charge,
including polishing cleaned and grouted with
matching colour cement paste, curing,
cleaning all complete at all heights and leads
to satisfaction and approval of the
Consultants. Care to be taken to ensure joints
are well grouted, cleaned and water tight.
Providing and laying rough chiseled dressed
stone flooring over 20 mm average thick base
of cement morat 1:5 (1 Cement : 5 Coarse
Sand) including pointing with cement mortar
1:2 (1 Cement : 2 Stone dust) etc. complete
(B) 40 mm thick stone.
Decorative Tiles:
Providing and fixing ceramic based elevation
tiles of any size but thickness of 8 mm to
mm at any height and level etc. complete. The
tiles shall be fixed with Chemical on finished
plaster and filling the joints with matching
cement colour and cleaning the tiles etc.
Providing cement vata (10 cms. X 10 cms
70 size) quarter round in cement mortar 1:1 300.00 Rmt. 23.45
including neat cement finishing, watering
Granite Counter:
Providing and fixing Black or any approved
colour Granite Stone Counter for wash basin
etc. The counter shall be sandwich type and
shall have Polished kotah stone as base on
which the granite stone shall be resting. The
counter shall be embedded in the wall atleast
50 mm and shall be self resting and / or
having granite stone as base. The visible
edges of the Polished Kotah stone shall be
cladded with the Granite stone. The shape of
the final product shall be of any shape in plan
and the measurements of plan area shall be
considered for payment.
Double Polished Granite Stone Shelves :
Providing and fixing 15 to 18 mm thick
double polished Granite stone shelves with
fixing the edge atleast 25 mm inside the wall,
corner edge polishing the edge and fixing the
stones vertically and horizontally. The
dimension of the finished and visible stone
shall be taken for payment. Rates includes
necessary onsite polishing, waxing, edge
moulding (If required).
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Granite Stone Partitions:
Providing and fixing Double side polished
to 18 mm thick any colour granite stone to be
fixed as a partition in wall. The size of a
partition shall be 1.20 Mts. X 0.90 Mts. One
side of 1.20 Mts length shall be embedded
atleast 50 mm in the wall vertically and shall
73 be fixed with Cement Mortar 1:1. The 20.00 Smt 1398.00
partition shall be fixed after cutting the stone
as per the design and pattern approved. The
partition shall be polished on both the sides
and shall be fixed as per the directions of the
project consultants. All the visible edges of
this stones shall be properly moulded and
polished on site.
Providing and fixing 10 mm thick multiwall
Polycarbonate roof sheets of approved make,
on structural roofing / sky light structures in
shapes as per Architect’s drawing. The rate
shall include cost of scaffolding, screws, nuts,
bolts and all necessary fixtures and fastening
etc. complete. Structural steel to be
measured and paid extra.
Providing and fixing Kotah stone and Granite
Sandwich Seating of 450 mm Height from
finished floor and 500 mm width. Rates
includes moulding and polishing of all the
visible edges. Providing double granite (Back
to back fixed) both visible sides polished
support at minimum 1000 mm centre to
center. and vertical at end shall be 200 mm
above the seating height. The corner of the
vertical shall be cut in half round of size 3" x
3" and the edges shall be moulded and
polished as per the instructions.
Measurement from Plan shall be taken for
Providing & Applying two coat of white putty
of Birla or equivalent at all levels to internal
plaster surfaces/POP surfaces of concrete,
masonry work including jambs, sills,
grooves, pattas, rounding of corners after
thoroughly brushing the surfaces free from
mortar dropping and other foreign matter
and also including preparing the surface
even and sand papered smooth etc. after
applying every coat of putty. Priming coat of
alkali resistant cement primer (water or
solvent based) is to be applied before at all
levels, all floors, all height, all complete as per
drawing, specifications, instruction &
directions of the Engineer-in-charge.
Payment shall be done as per drawing/laid at
site of plastered area. Approved Brands : J.K.
White, Birla, Asian.
Applying priming coat over new steel and
other metel surface after and including
77 preparing the surface by throughly cleaning, 1200.00 Smt. 34.34
oil, grease, dirt and other foreign matter and
scoured with brushes fine steel wood,
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
scrapers and sand paper with ready mixed
priming paint brushing red lead.
Painting two coats (excluding priming coat)
on new steel and other metal surface with
enamel paint, brushing, interior to give an
even shade including cleaning the surface an
even shade including cleaning the surface of
all dirt, dust and other foreign matter.
Painting one coat extra on new steel and
other metal surface with enamel paint,
brushing, interior to give an even shade
including cleaning the surface an even shade
including cleaning the surface of all dirt, dust
and other foreign matter.
Wall Painting (two coats) with plastic
emulsion / Oil paint of approved brand and
manufacture and of shade required on
undecorated wall surfaces to give an even
shade, over and including a priming coat with
80 alkali resistance primer of approved brand 7200.00 Smt. 78.44
and manufacture after thoroughly brushing
the surface free from mortar droppings, and
other foreign matter and also including
preparing the surface even
and sand -papered smooth
Wall painting with plastic emulsion paint for
subsequent coat of approved brand and
manufacture on undecorated wall surface to
81 give an even shade including thoroughly 7200.00 Smt. 33.39
brushing the surface free from mortar
droppings and other foreign matter and sand
papered smooth.
Providing and applying 2 mm thick rustic
type texture of specified quality approved
make make of Asian, Nerolec or equivelant
as per approval of EIC over plastered surface,
at all levels, all floors, all height, all complete
as per drawing, specifications, instruction &
directions of the Engineer-in-charge,
including scaffolding charges. Payment shall
be done as per drawing/laid at site of
plastered area.
Finishing wall with weather proof exterior
smooth emulsion paint on wall surface (two
coats) to give an even shade after thoroughly
83 brushing the surface to remove all dirt, dust 5000.00 Smt. 174.97
and remains of loose powdered materials etc.
complete. Primer coat shall be done before
starting this external paint.
Providing & laying M/F Suspended single
layer of 12.5mm tapered edge Gypsum Board
ceiling , which includes metal frame work
with using CS55, IC91, PC55, CA55 CRP
surface ribbed perimeter channels with the
84 help of nylon sleeves and screws at 610 mm 2400.00 Smt. 600.94
centres along the perimeter of ceiling. Then P
Steel CRP surface ribbed intermediate
channels of size 45mm from the soffit at
1220mm centres with P Steel™ CRP surface
ribbed ceiling angle fixed to soffit with cleat
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
and steel expansion fasteners. Then P Steel™
CRP surface ribbed Ceiling section are then
fixed to the P Steel™ intermediate channel
with the help of connecting clip and in
direction perpendicular to the P steel™
intermediate channel at 457.5mm centres.
Single layer of 12.5 mm Gypsum boards are
then screw fixed to ceiling section with
25mm drywall screws at 230mm centres.
Finally square and tapered edges of the
boards are to be jointed and finished so as to
have a flush look which includes filling and
finishing with Jointing compound, Joint
Paper tape and two coats of Drywall Top
Coat. Rates shall be inclusive of cost of
making cut outs/openings for electrical
fixtures, tube lights /air-conditioners grills,
diffusers etc. & providing additional sections
for strengthening the openings/cutouts,
making grooves between wall & board or as
per drawing /instruction of EIC . Area of
cutouts shall not be deducted and no extra
payment shall be considered for additional
sections provided . Only plan area shall be
considered for payment. All curved surfaces,
recesses, waffles and corbellings shall be part
of the false ceiling & flat area in plan shall be
measured for payment (Section must from P
SteelTM Brand)The rate shall be in sq.mt. for
all floors and at all heights including all costs.
The rates are also inclusive of necessary
scaffolding, tools, tackles etc. The shop
drawing (or a sample mock of 5 sqm
minimum of the frame work and ceiling)
shall be approved from EIC . Groove shall be
provided at the junction of the false ceiling &
the wall & including all accessories, material
& labor complete as directed by Architect /
Engineer – in – charge.
Providing and fixing Plaster of Paris ceiling
with G.I suspenders etc. Complete
Providing and fixing 12 mm thick cement
sheet with necessary carving (as per design
approved) and fixing it with screws on M.S.
Pipe , wall , ceiling etc. Complete. This
includes necessary Painting with one coat of
Providing and fixing border pattis of
approved quality of teak wood. Rate includes
necessary screwing, nailing, fixing etc.
complete. Rate also includes giving the
border patti french polish of approved shade.
Before polishing the pattis shall be scrapped
with sandpaper and three coats of french
polishing shall be done as per the
instructions and directions of the engineer in
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Providing and fixing Waterproof wall paper
at any height, level as directed.
Providing and fixing aluminium extruded
section body tubular type universal
hydraulic door closer (having brand logo
with ISi, IS : 3564, embossed on the body,
door weight upto 36 kg to 80 kg and door
width from 701 mm to 1200 mm), with
double speed adjustment with necessary
accessories and screws etc. complete.
Approved brandes Ebco, kadson, falcon or
equivalent ISI make as directed etc.
Providing and fixing Glass Bricks of approved
size (preferred size: 190 mm x 190mm x
90 mm). Colour Preferred : oceanic blue , Milky 150.00 Nos. 400.00
white and clear glass. Rate includes all
necessary grout / chemical etc. required to
fix the glass bricks.
Providing and fixing clear / colour acrylic
plate (3 to 4 mm thick) for making signages Sq.
with vinyl letters and back painted (in case of Inches
clear acrylic). Rate includes fixing the plate
with studs at any height and level.
Aluminum Composite Panel:
Providing and Fixing Alluminium Composite
Panel of (approved make by Architect) 4 mm
thick exterior grade 30 micron PVDF with
coil thick of 0.25 mm & frame work made out
from Alluminium anodised section of size
x 25 mm ( w app = 0.57 kg/m) having weight
of 2.6 kg for 15' supported on Masonary/
RCC with the help of MS Bracket fixed with
Brick Fastner/ Anchor Fastner and groove
92 filled with silicon grade 995 and 789 and G.P 50.00 Smt. 3403.00
Where it is necessary at pressure tape Baker
Rod size depend upon gape between two
Panel of bowl corning corporation make etc.
complete as per Architect dwg. and as per
instruction of E.I.C. (Rate are included
providing & fixing of MS structure steel work
for fixing of Alluminium Composite Panel
when and where requried). Preferred Brands
EVA, Flexibond, Alu-decor, Timex and
colours as approved by the Consultants.
Providing and fixing Stainless steel brush /
matt finish metal letters (1” x 1” and height
as per requirement) in any language as
directed.Rate includes fixing the same at any
height and level as directed by the project
consultants. This includes providing
93 temporary structures at any height and level 1400.00 Inch. 93.85
etc. complete. For measurement, width and
height of the letter shall be measured,
whichever is higher, shall be measured in
Running inch and paid accordingly. For any
logo, the measurement of height and width
shall be measured and total inches shall be
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
calculated 1.50 times and shall be paid
Providing in line level plumb, fabricating and
fixing three row horizontal barbed wire
fencing and punched tape concertina coil of
turns per meter of 610 mm diameter fixied
with clips on top of the angle iron posts. The
punched tape concertina coil having sharp
barbs at every 25 mm spacing shall be
mm thick and 19 mm width and weighting
Kg./100 mtr. (Average) as per manufacture's
specification. The rate shall also include
providing and fixed 1.20 mt. total long MS
angle 40 x 40 x 6 mm @ 3.00 mt. c/c spacing
embedded in RCC column, angle posts shall
be painted with one coats of red oxide and
two coats of enamel paint of approved
quality at top of compound wall.
Providing and fixing 1.20 Metre high fencing
with 2.0 Metre long M.S. Angle posts 40 mm
x 40 mm x 6 mm and oil painting 3 coats fixed
at 2.5 Mt,C/c. with five Horizontan lines and
two diagonals of galvanised steel barbed
wire weighting 9.38 Kg. per 100 Metre,
strained and fixed to posts with G.I,staples
including fixing the postsin ground with
M x 0.5.M x 0.5 M. block in C.C1:5:10 etc.
Providing and fixing 23 cms wide chicken
96 mesh jaali with nails & then application of 15 165.00 Smt. 292.59
mm plaster on R.C.C. & Masonary joints as
per directed of Engineer in Charge
Providing throating or plaster drip, grooves
and moulding to Wall , R.C.C. chajja and slab.
Providing and fixing stainless steel (Grade
304) railing,daso, grill work etc. made of
Hollow tubes, channels, plates etc., including
welding, grinding, buffing, polishing and
making curvature (wherever required) and
fitting the same with necessary stainless
steel nuts and bolts omplete, i/c fixing the
railing with necessary accessories &
98 stainless steel dash fasteners , stainless steel 300.00 Kgs. 650.00
bolts etc., of required size, on the top of the
floor or the ide of waist slab with suitable
arrangement as per approval of Engineer-in-
charge, ( for payment purpose only basis of
standard theorical weight of stainless steel
members shall be considered. No extra shall
be paid for fixing accessories such as nuts,
bolts, nails, fasteners etc.).
Making "V" Notch , Moulding , in any kind of
tiles / stone etc.
Chainlink Fencing :
Chainlink Fencing ( 4' 0" Tall ) with
Necessary 3" Diameter M.S. Pipe of size
Mts. and frame of 35 x 35 x 5 mm M.S. angle
and fixing with 25 x 5 mm M.S. Flat, including
necessary foundation work with R.C.C. 1:2:4,
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
of size atleast 350 mm x 350 mm x 230 mm.
Rate also includes painting all the steel works
with one coat of Primer coat and 3 coats of
approved brand and shade oil bound enamel
paint, etc. complete. The spacing of the
chainlink shall be not more than 50 mm c/c,
and the gauge of the wire used shall be
Groove cutting in Stone :
Making of 2 to 3 mm groove in Kotah stone /
any stone / granite etc. in steps / stairs so as
to give an anti skiding effect. This shall be
done as per the instructions and pattern
given by the consultants.
Providing and fixing Structural Glazing with
using the 17 Micron anodised of approved
colour alluminium section as transium,
mullium of size 63mm x 38mm x 2 mm with
using 6 mm thick reflective structural glass of
approved make, colour / Tinted, toughned
and shade and fixed with silicone sealant and
spacer tap and at corner sealed neoprene
foam dust and Air sealed gasket mirred
including scaffolding, cleaning of glass
etc.complete at all heights anf lifts with all
necessary fitting and fixtures, anchore
fasteners, necessary M.S. or Aluminium
brackets, suitable design for openable or
sliding window as per Architectural drawing
and as directed by Engineer-in-charge.
Grooves between the glasses to be filled with
sealant of Dow corning - structural sealant
995, weather sealant 789. The entire facade
should be water proof. The mullions are to be
connected to bracket by SS-304 nut bolts.
Measurement shall be given as per actual
execution of the work. (M.S. fabrication shall
be measured and paid seperately)
Providing & Mixing of Water proof Chemical
in Cement mortar for Inside/ outside Plaster
103 work of "Roof " , "Fosroc" or equivalent make 100.00 Lits. 225.00
in proportion as per company's user manuals
& Direction of engg. In charge.
Providing and fixing furniture under
platform. Providing and fixing wooden
furniture made from wood and plywood. The
frame shall be made from wood of size
mm x 25 mm and the shutters shall be made
from 19 mm MR grade plywood. The inner
side of the shutters shall be cladded with
mm thick laminate (of approved brand and
shade) while the outer side of the plywood
shall be cladded with 1.0 mm thick laminate
(of approved brand and shade). The hinges
shall be "W" type steel hinges and the storage
shall have atleas one lock and one stopper.
The hinges used shall be of heavy type
Stainless steel hinges and the thickness of the
shutter shall be cladded with 12 mm thick
border patti. This border patti shall be
polished (approved shade) in melamine
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
finish. For payment, the elevation
measurement i.e. height and width of the
storage shall be measured and paid as per the
unit mentioned in the BOQ.
Providing and fixing Sun control reflective
105 type films on glass doors / windows etc. As 225.00 Smt. 646.37
Providing & Fixing in Position Vertical Roller
Blinds with Minimum 3 % and Maximum 5 %
Light Transperace Screen Fabric Incuding
Providing & Fixing of Powder coated G-
Channel at the Topof Window with necessary
Screw , Cleats etc. and PVC Roller ( Weight
Pipe) and PVC Chain For Up and Down
106 Movement of Blinds etc. of Approved Make 100.00 Smt. 1372.03
and as per Drawings / Instruction of Engg. in
Charge For All Colors and Shades. Rates
Includes all Lead and Lift For All Floor Level,
All Height , All Material , Accessories, Fixing
Scaffolding , Labor etc. Complete in All
Respects. All Required Accessories &
Material must be From Same Manufacturer.
Providing and installing heavy duty
Aluminum cubicle track of size 20 mm
(width) x 30 mm (ht.), powder coated and
continuous pvc linter, nylon guiders,hooks,
plastic end caps, connecting bridge
107 overlapping joint connector, wall bracket etc. 50.00 Smt. 737.29
complete to make cubicle of size
approximately 2100 to 2400 mm clear from
the floor. The curtain system shall be of
Hospital standard and shall be approved by
the consultants.
Supply and Installation of Waterproof, anti-
microbial cubicle curtain with heavy
strength (18" oval net) at top and eyelets on
108 curtains and hooks. This includes all 125.00 Smt. 400.00
necessary accessories, fixing at any height
and level etc. complete as per the manual of
the manufacturer.
Painting with weatherproof exterior
emulsion acrylic based paint the National
Urban Health Mission Logo and Ayushman
Bharat Logo type using the grid and
dimension given as per defined shade code
109 by experienced applicator of standard 1.00 Nos 9200.00
drawing and design according to the
reference manual of Facade Branding for
Health & Wellness Centres of Ayushman
Bharat Scheme as per the direction of the
Engineer in Charge.
Painting the illustration circle of Diameter
inch with weather proof exterior emulsion
acrylic based paint as per defined shade code
by experienced applicator of standard
110 drawing and design according to the 12.00 Nos 2818.00
reference manual of Facade Branding for
Health & Wellness Centres of Ayushman
Bharat Scheme as per the direction of the
Engineer in Charge.
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Painting with weatherproof exterior
emulsion acrylic based paint the pattern
using the grid and dimensions for door and
window given as per the defined shade code
by experienced applicator of standard
drawing and design according to the
reference manual of Facade Branding for
Health & Wellness Centres of Ayushman
Bharat Scheme as per the direction of the
Engineer in Charge.
Providing and fixing to wall, ceiling and floor
galvanised mild steel tubes (Medium Grade)
112 of the following nominal bore, tube fittings
and clamps including making good the wall,
ceiling and floor
(b) 20 mm Diameter. 10.00 Rmt. 297.25
(c) 25 mm Diameter 10.00 Rmt. 393.93
(d) 32 mm Diameter 10.00 Rmt. 491.51
(e) 40 mm Diameter 10.00 Rmt. 596.73
(f) 50 mm Diameter 10.00 Rmt. 779.60
Providing and laying in trenches galvanised
mild steel tubes (medium grade) of the
113 following nominal bore and tube fitting
(Earthwork in trenches to be measured and
paid for seperately).
(b) 20 mm Diameter. 20.00 Rmt. 190.97
(c) 25 mm Diameter 25.00 Rmt. 279.39
(e) 40 mm Diameter 45.00 Rmt. 421.12
(f) 65 mm Diameter 45.00 Rmt. 716.66
Providing, laying and jointing in true line and
level 15 mm dia. U.P.V.C. pipe (Schedule 40)
for cold water including fittings make
PRINCE/ SUPREME/ ASTRAL/FINOLEX or
equivalent brand as approved by Engineer in
charge. Pipes shall be fixed on the wall with
the help of clamp at every 2.00 meters c/c of
shall be concealed as directed including
necessary fittings etc. including testing of
pipe and joints and fixing the same with
adhesive solvent, including cost of all
materials etc. complete.
(a) 15 mm Diameter 50.00 Rmt. 71.93
(C) 25 mm Diameter 145.00 Rmt. 90.93
(d) 32 mm Diameter 115.00 Rmt. 117.97
(e) 40 mm Diameter 115.00 Rmt. 146.65
(f) 50 mm Diameter 165.00 Rmt. 193.73
Providing and fixing concealed center point
to wall, ceiling & floor CPVC (SDR 13.5) Pipe
having National Sanitation Foundation (NSF)
115 seal for potable water of following diameter
nominal bore tube fittings and clamps
including making good the wall, ceiling and
floor etc. compelte for (A) 15 mm Diameter.
(a) 15 mm Diameter 10.00 Rmt. 165.21
(b) 20 mm Diameter. 10.00 Rmt. 202.97
(C) 25 mm Diameter 10.00 Rmt. 247.25
(d) 32 mm Diameter 10.00 Rmt. 330.36
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
(e) 40 mm Diameter 10.00 Rmt. 437.66
(f) 50 mm Diameter 10.00 Rmt. 647.30
Providng and fixing to wall ,ceiling and floor
10.00 kg. F/Sq. Cm2 working pressure
polythelene pipes of the following outside
diameter, low, density, complete with special
flange compression type fittings, wall clips
etc. making good wall ceiling and floor.
(a) 32 mm Diameter 50.00 Rmt. 116.40
(b) 75 mm Diameter 150.00 Rmt. 274.68
( c) 110 mm Diameter 200.00 Rmt. 332.91
Providing and fixing in position cowel vent to
(B) 75 mm diameter. 20.00 Nos. 385.88
Providing and fixing in position cowl vent to
(C) 100 / 110 mm diameter. 25.00 No. 496.90
Providing and fixing PVC Nahni trap
(Cockroach Trap) of the following nominal
diameter of self cleaning design with C.I.
119 screwed down or hinged grating including 20.00 No. 552.83
cost of cutting and making good the walls and
floor 100 mm inlet and 50 mm outlet. ( C)
100 mm Diameter.
Providing and fixing Water closet squatting
pan (indian type W.C. pan) size 580 x
mm. (A) Vitreous china Long pattern.The
closet shall be of approved brand and shade.
Providing and fixing of wall hung type with
concealed P or S trap Including jointing the
trap with soil pipe in cement mortar 1:1
(1cement : 1 fine sand) and in white colour
directed by Engineer-in-charge Including
121 cost of all material, labour, duroplast soft 18.00 Nos. 12613.27
close seat cover, jetspray, CI Chair Bracket,
SS Bolts and washers all complete as per
detail drawing and instructions of Engineer
in Charge. Reference Rates for Model : Cera
Health faucet - Providing & fixing of Hand Jet
Shower (Health Faucet) with 1 mtr Flexible
122 PVC Tube, wall hook, and 2-Way Bib Cock. 18.00 Nos. 1543.36
This is a consolidated item which includes
Providing and fixing 100 mm size P or S trap
for water closet squatting pan including
123 jointing the trap with the pan and soil pipe in 20.00 Nos. 311.85
cement mortar 1:1 (1 Cement : 1 Fine sand)
(A) Vitreous China.
Providing and fixing plastic seat and cover
for wash down water closet with C.P. brass
hinges and rubber buffers.(B) Black plastic
seat and cover.
Providing and fixing C.P. Brass waste for
washbasin or sink.
(A) 32 mm Diameter. 25.00 Nos. 67.24
(B) 40 mm Diameter. 25.00 Nos. 88.94
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Providing and fixing M.I. Fisher union for
washbasin or sink.
(A) 32 mm diameter. 25.00 Nos. 77.97
(B) 40 mm diameter. 25.00 Nos. 87.77
Providing & fixing stainless steel sink, R.S. or
C.I. Painted brackets painted, 40 mm dia. C.P.
waste, C.P. brass chain and rubber plug,
strainer with necessary C.P. brass unions
complete including painting the fittings
127 and cutting and making good the walls 2.00 No. 2257.69
wherever required, with CC sink cock with
raised "J" shaped swinging spout. The scope
includes the following fixtures.(Make: Nirali-
Grace-plain-510 mm x 432 mm bowl with
Swan neck tap or equivalent).
Providing and fixing Providing and fixing
Ceramic Sink of Size 600 x 400 x 200 mm
deep (660 x 460 including rim). The rates
includes brackets, painted white including
cutting holes in platform and making good
the same but excluding fittings.. The rates
includes brackets, painted white including
cutting holes in platform and making good
the same but excluding fittings. Reference
Rates for Model : Cera Carat
Providing and fixing C.P. Brass shower rose
with 15 mm or 20 mm inlet. (A) 100 mm dia.
Approved Brands : Donald, ESS ESS, KCI, with
ceramic sprindels and half turn fixtures.
Providing and Fixing of C.P. Brass BIB Cock of
15 mm Dia of Jaquar make florentine series
130 model no. 5047n or equivalent but Approved 32.00 No. 1564.17
make & Model with all necessary fittings. as
approved by Engineer - in - charge.,
Providing and Fixing of C.P.Brass Pillar Cock
of 15 /20 mm Dia. of Jaquar make model no.
5011n or equivalent make with all necessary
fittings. as approved by Engineer - in -
charge., Ceramic Sprindel, Half turn, Heavy
duty. Approved Brands : Donald, ESS ESS, KCI
Providing & Fixing S.S type soap dish of
approved by consultant/Architect, including
civil cutting & backfilling as well as making
good the walls.
Providing and fixing brass angle cock ( C)
mm diameter. Ceramic Sprindel, Half turn,
Heavy duty. Approved Brands : Donald, ESS
Providing and fixing ball valve (brass) of
approved quality, High or low pressure, with
plastic floats complete :
(a) 15 mm Diameter 12.00 Nos. 886.22
(b) 20 mm Diameter 1.00 Nos. 1099.94
( c) 25 mm Diameter 20.00 Nos. 1552.93
(d) 40 mm Diameter 1.00 Nos. 3312.60
( e) 50 mm Diameter 2.00 Nos. 4613.48
Providing and fixing Full Way valve with
wheel of approved quality :
(a) 15 mm Full Way valve 1.00 Nos. 1461.17
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
(b) 20 mm Full Way valve 1.00 Nos. 1924.61
(c) 25 mm Full Way valve 16.00 Nos. 2535.55
(d) 32 mm Full Way valve 1.00 Nos. 3377.64
(e) 40 mm Full Way valve 6.00 Nos. 4661.10
(f) 50 mm Full Way valve 2.00 Nos. 6675.14
Providing and Fixing of swan neck Sink Tap
Wall mount/Plateform Mount Jaquar make
135 model no. 5357 n or equivalent make. Rate 12.00 Nos. 2622.00
shall Including of cost of labour, material,
necessary fittings etc.
Providing fixing of SS grab bar of Jaquar
make model no. 1507 or equivalent make
with all hardwares for Physically Handicap
Providing and fixing chromium plated bottle
trap with necessary couplings of approved
quality for wash basin. Approved Brands :
Donald, ESS ESS, KCI
Providing and fixign S.W. gully trap with C.I.
grating brick masonary chamber and water
tight C.I. cover with frame of 300 mm x
mm size (inside) with standard weight .
(A) 100 mm x 100 mm size P- Type. 20.00 No. 1279.40
(B) 150 mm x 100 mm size P- Type. 20.00 No. 1234.57
Providing and laying cement concrete
1:5:10 (1 cement : 5 fine sand: 10 graded
stone aggregate 40 mm nominal size)
139 bedding for stone ware pipes of following 50.00 Rmt. 125.90
internal diameter with necessary formwork
and curing complete (For 100 mm Dia. pipes
and average 112 mm bed thickness)
Providing and laying cement concrete
1:5:10 (1 cement:5 fine sand: 10 graded
stone aggregate 40 mm nomonal size)
140 bedding for stone ware pipes of following 100.00 Rmt. 211.59
internal diameter with necessary formwork
and curing complete (For 150 mm Dia pipes
and average 166 mm bed thickness)
Providing And Jointing Stoneware Pipes
Including Excavation Up to 2.00 Mt. Refilling,
Transporting Pipes To Work Site, Unloading,
Lowering In Trench, jointing material Such
141 As Cement, sand, Hemp Bitumen As Directed, 100.00 Rmt. 344.64
Incl. Watering The Trenches Spreading And
Carting away Of Surplus material as directed
by Engineer in-charge for (C) 230 mm
Providing and Laying (to level or slopes) and
jointing reinforced concrete Light Duty Non-
pressure pipes I.S. Class NP2 of 250 mm
diameter with collars and butt ends prepared
for collar joints including testing of joints
Constructing brick masonary chamber for
underground C.I. inspection chamber and
bends with bricks having crushing strength
not less than 35 Kg/Cm2 in Cement Mortar
1:5, C.I. Cover with frame (Light Duty)
mm x 610 mm internal dimensions total
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
weight of the cover with frame to be not less
than 38 Kg.(Weight of cover 23 Kg. and
weight of Frame 15 Kg.), R.C.C. top slab with
1:2:4 mix (1 Cement : 2 Sand : 4 Coarse
Aggregates) foundation concrete 1:5:10
inside plaster 15 mm thick with cement
mortar 1:3 finished smooth with a floating
coat of neat cement on walls and bed
concrete etc. complete. (i) Inside dimensions
455 mm x 610 mm and 450 mm Deep for
single pipe line.
Constructing brick masonary chamber for
underground C.I. inspection chamber and
bends with bricks having crushing strength
not less than 35 Kg/Cm2 in Cement Mortar
1:5, C.I. Cover with frame (Light Duty)
mm x 610 mm internal dimensions total
weight of the cover with frame to be not less
than 38 Kg.(Weight of cover 23 Kg. and
144 weight of Frame 15 Kg.), R.C.C. top slab with 5.00 Nos. 3624.51
1:2:4 mix (1 Cement : 2 Sand : 4 Coarse
Aggregates) foundation concrete 1:5:10
inside plaster 15 mm thick with cement
mortar 1:3 finished smooth with a floating
coat of neat cement on walls and bed
concrete etc. complete. (i) Inside dimensions
500 mm x 750 mm and 450 mm Deep with
one or two inlets.
Constructing brick masonary chamber for
underground C.I. inspection chamber and
bends with bricks having crushing strength
not less than 35 Kg/Cm2 in Cement Mortar
1:5, C.I. Cover with frame (Light Duty)
mm x 610 mm internal dimensions total
weight of the cover with frame to be not less
than 38 Kg.(Weight of cover 23 Kg. and
145 weight of Frame 15 Kg.), R.C.C. top slab with 4.00 Nos. 7109.35
1:2:4 mix (1 Cement : 2 Sand : 4 Coarse
Aggregates) foundation concrete 1:5:10
inside plaster 15 mm thick with cement
mortar 1:3 finished smooth with a floating
coat of neat cement on walls and bed
concrete etc. complete. (i) Inside dimensions
600 mm x 850 mm and 450 mm Deep with
three or more inlets.
Constructing manhole with RCC top slab in
1:2:4 mix foundation concrete in 1:3:6 mix
inside plastering 15 mm thick with Cement
Mortar 1:5 finished with a floating coat of
neat cement and making channels in cement
concrete 1:2:4 finished smooth complete
including curing and festing (i) Inside
146 mm x 1200 mm and 1.5 Mt deep including 1.00 Nos. 10920.76
C.I. Cover with frame size 560 mm diameter
total weight of cover and frame to be not
less than 128 Kgs.( Weight of Cover 64 Kgs
and weight of Frame 64 Kgs.) (A) With
mm thick walls of brick masonary using
bricks having crushing strength not less
than 35 Kg/ Cm2 in cement mortar 1:5(1-
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Cement: 5 Coarse Sand) (1) A type depth
0.90 Mt for any dia sewer.
Constructing manhole with RCC top slab in
1:2:4 mix foundation concrete in 1:3:6 mix
inside plastering 15 mm thick with Cement
Mortar 1:5 finished with a floating coat of
neat cement and making channels in cement
concrete 1:2:4 finished smooth complete
including curing and festing (i) Inside
mm x 1200 mm and 1.5 Mt deep including C.I.
147 Cover with frame size 560 mm diameter total 1.00 Nos. 19139.07
weight of cover and frame to be not less than
128 Kgs.( Weight of Cover 64 Kgs and weight
of Frame 64 Kgs.) (A) With 230 mm thick
walls of brick masonary using bricks having
crushing strength not less than 35 Kg/ Cm2
in cement mortar 1:5(1- Cement: 5 Coarse
Sand) (1) B type depth 1.50 Mt for any dia
Providing & Fixing F.R.C. M.H./ CH.seat &
cover incl. carting to the work site etc. comp.
directed. F.R.C. Extra Heavy Duty (EHD-35)
Manhole Covers & Frames Cover : 728 mm ø
& 100 mm thick circular cover, 35.00 MT load
design, 100 x 2 mm M.S flat allround, 16mm
ø plain round bar for lifting the cover &
should be fitted with plastic cups. Frame :
560 mm ø clear opening, outer size-
888x888x175 mm. On the upper periphery
of frame 25 x 3 mm wide MS flat should be
well embed in concrete to protect the edges
of frame. FRC E.H.D.-35 manhole cover &
frame described as above.
Providing & Fixing F.R.C. M.H./ CH.seat &
cover incl. carting to the work site etc. comp.
directed. For FRC heavy duty cover size
mm. & 90 mm thick circular cover 20 M.T.
design load and frame size 560 mm clear
opening size 890 x 890 x 120 mm.
Providing and fixing in position with clamps
etc. 32 mm nominal internal diameter
galvanised steel tube flush pipe for high level
flushing cistern including connecting the
flush pipe with cistern and closet and making
good walls and floors.
Providing and fixing 12.5 Liters low level
flushing cistern with a pair, of C.I. or Mild
Steel Brackets complete with fitings uch as
lead valve less syphon, 15 mm nominal size
brass ball valve with polythene float, C.P.
151 brass handle unions and couplings for 15.00 Nos. 2321.21
connections, with inlet, outlet and overflow
pipes, 40 mm dia. porcelain enamelled flush
bend including cutting holes in walls and
making good the same connecting the flush
bend with cistern and closet.
Providing and fixing coloured glazed oval
type counter wash basin 520 x 450 mm in
152 size and make specified by the consultants 12.00 Nos. 6641.14
with one C.P. pillar cock, C.P. stop cock, P.V.C.
feed pipe C.P. waste coupling (32 mm),
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
rubber plug etc.complete. Rates includes
necessary cutting of platform, inner edge
moulding-polishing, and filling the gap with
approved shade silicon complete. Approved
Brands : Cera, Parryware, Soncera.
Providing, erecting and fixing double coated
Sintex, National, Reno or equivalent PVC (ISI)
water tank of required capacity each with all
153 necessary fittings and connections etc. 5000.00 Ltr. 3.91
complete on terrace at any height and level.
Approved Brands : Sintex, Reno, National,
Providing and fixing urinal of approved
quality including connection with trap and
with integral longitudinal flush pipe
(A)Large Urinal 550 mm x 300 mm x
mm. with standard flush pipe, Waster Pipe,
154 Waste Coupling, PVC Connection and G.I 10.00 Nos. 3344.35
clamps complete, including painting of
fittings and brackets, cutting and making
good the walls and floors wherever
requiredApproved Brands : Cera, Parryware,
Providing and fixing Cast iron steps of size
500 mm x 150 mm x 22.5 mm and painting
with two coats of anti-corrosive paint etc.
Providing and fixing 600 mm x 450 mm
bevelled edge mirror of superior glass
155 mounted on 6 mm thick A.C. sheet or 20.00 Nos. 825.48
plywood sheet and fixing to wooden plug
with C.P. brass screws and washers.
Providing and fixing C.P. brass towel rail
complete with C.P. brass brackets fixed to
wooden plugs with C.P. brass screws (B)
mm x 20 mm size.
Constructing Bombay pattern type catchpit
of size 0.60 x 0.60 mt depth up to 1.00 Mt.
including excavation BBCC (1:5:10) 23 cms
thick brickwalls in c:m (1:6) with 40 mm
thick IPS flooring in the proportion M15 at
bottom and 20 mm thick cement plaster
inside the catchpit in the prop of c:m(1:3)
without jali etc comp as directed.
Providing and fixing FRC catchpit jaali with
159 frame 600 mm x 600 mm clear opening etc. 20.00 Nos. 1383.93
Complete as directed by Eng. In charge.
Providing and fixing accessories of following
a) Long Body Doctor lever Cock 6.00 Nos. 2500.00
b) Two Way Bib Cock 12.00 Nos. 1426.00
c) 32 mm Dual Flush Metropole 8.00 Nos. 4500.00
Making connection to the existing Manhole in
running sewer including Dewatering and
other required machinery etc. of following
dia pipes at any convenient time. All
damaged work shall be well repaired as per
instructions. etc..complete.
(a) For Pipe 150 mm to 300 mm diameter 1.00 Nos. 1339.29
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
(b) For Pipe 400 mm to 600 mm diameter 1.00 Nos. 2232.14
Making connection of galvanised Mild steel
distribution branch with galvanised mild
162 steel main pipe upto 80 mm nominal bore by 1.00 No. 600.08
providing and fixing tee including cutting
and threading the pipes complete
Hiring Charges For J.C.B.Machine Including
Cost Of Fuel, Operator, Dirver Etc..
Hiring of Tractor with trolley considering
Hrs. As working Day hours inclu. Driver
(GWSSB SOR-2022-23 Section-2E-
Miscellenous Item No.7)
B PERCOLATING WELL
Drilling of pilot bore hole in alluvial strata by
165 direct rotary rig of 250 mm diameter.
166 Reaming 400 mm. 100.00 Rmt. 212.50
Electrologging charges with conveyance etc.
Providing and installing 200 mm diameter
(IS:12818) UPVC casing pipe- "CM" class 100.00 Rmt. 1193.75
168 plain pipe.
Providing and installing 200 mm diameter
(IS:12818) UPVC End cap, with Air vent 1.00 Set 669.64
Providing and laying 200 mm diameter
regular pipe with 1.5 mm sloted size cage
type trapezoidal shape wire wound little 100.00 Rmt. 1146.43
carbon galvanised screen confirming to IS:
171 Supplying and filling Pea size gravels 10.00 Cmt. 2029.46
Providing and fixing Air vent with 50 mm
Lowering and removing of dropline upto
173 Desired depth.
Using Air Compressor 60 CFM/150 PSI for
C LANDSCAPE WORKS
Providing good quality fertile soil, mixing
manure etc. Complete and making sub base
175 clear for laying lawn and other plantation etc. 500.00 Cmt. 450.00
Complete ( Item to be operated and paid only
for garden items).
Supplying Good Quality River Kamp as
directed etc comp.
Spreading of good earth like fertile river soil
or farm earth as directed and approved.
Supply and planting of Ficus panda, Ficus
178 benjamina, Ficus benjamina variegated, 10.00 Nos. 150.00
Ficus longisland bag size is 13 inch x 13 inch,
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
well branched, well established & free from
disease at site as per the instructions
Supply and planting of (Jasud, Ixora, Ticoma
Gaudi-chaudi, Gultora, Jetropha, Haemeliya,
Chandani, Mogaro, Galfemia, , Allamenda,
Desi Gulab, Euphorbia mili, Jasud Hybrid,
Chandani double, Madhukamini,
179 Madhumalti, Ticoma Capensis, Ixora draft, 100.00 Nos. 150.00
Nikadevia, English Karen etc.) having height
of minimum 2.00 to 2.5 ft. and bag size is
inch x 13 inch, well branched, well
established & free from disease at site as per
the instructions.
Supply and planting of common Medicinal
Plants like Ardusi, Aloe spp., having height of
minimum 2.00 to 2.5 ft. and bag size is 8 inch
x 10 inch, well branched, well established &
free from disease at site as per the
Supply and planting of Exotic and
Endengered Medicinal Plants like Insulin
plant, zer kochalu having height of minimum
2.00 to 2.5 ft. and bag size is 13 inch x 13 inch,
well branched, well established & free from
disease at site as per the instructions.
Supply and planting of Golden Bamboo
having height of minimum 5 to 6 ft. and bag
182 size is 8 inch x 10 inch, well branched, well 1000.00 Nos. 45.00
established & free from disease at site as per
the instructions.
Supply and planting of champa (deshi)
having height of minimum 8 to 10 ft. and bag
183 size is 15 inch x 16 inch, well branched, well 50.00 Nos. 450.00
established & free from disease at site as per
the instructions.
D OXYGEN PIPE LINE WORKS
Providing and fixing oxygen point at any
height and level.
Providing and fixing BPC flow meter with
humidifier bottle.
186 Providing and fixing Pin Adoptor 50.00 Nos. 592.00
Providing and fixing 28 mm copper pipe at
187 any height and level including accessories 176.00 Rmt. 1691.00
Providing and fixing 15 mm copper pipe at
188 any height and level including accessories 250.00 Rmt. 943.00
Providing and fixing 15 mm isolation valve at
189 any height and level including accessories 50.00 Nos. 1875.00
Providing and fixing 28 mm isolation valve at
190 any height and level including accessories 4.00 Nos. 5135.00
Providing and fixing alarm system as per the
requirement and standard practice.
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
E ELECTRIFICATION WORKS
Providing and fixing Main LT Panel near
192 Meter as per attached SLD 1.00 Job
(Job that includes)
2 I/c MCCBs, 400A(35kA), FP 1.00 Nos. 24979.00
3 O/G MCCBs, 250A(35kA), FP 2.00 Nos. 20739.00
4 O/G MCCBs, 125A(35kA), FP 1.00 Nos. 7976.00
5 O/G MCBs, 63A(10kA), FP 1.00 Nos. 730.00
6 O/G MCBs, 40A(10kA), FP 1.00 Nos. 662.00
FP SPD (1.4KV, 40KA, 8/20 Micro-second)
Equivelent to LEGRAND MAKE CAT.
Rotary Handle with all accessories.
100A-125A Rotary Handle with all
11 400A Cu. Busbars 1.00 RMT. 7247.00
12 250A Cu. Busbars 1.00 RMT. 4861.00
13 125A Cu. Busbars 1.00 RMT. 3171.00
14 100A Cu. Busbars 1.00 RMT. 1942.00
15 Voltmeter 1.00 Nos. 1263.00
16 Ammeter 1.00 Nos. 1543.00
17 Voltmeter Selector Switch 1.00 Nos. 314.00
18 Ammeter Selector Switch 1.00 Nos. 314.00
19 Energy Meter 1.00 Nos. 2670.00
20 SP MCBs, 6A(10kA), SP 8.00 Nos. 111.00
22 Indicating Lamps 12.00 Nos. 43.00
Providing and fixing Main LT Panel for 2F+3F
as per attached SLD
1 O/G MCCBs, 250A(35kA), FP 1.00 Nos. 20739.00
2 O/G MCCBs, 125A(35kA), FP 3.00 Nos. 7976.00
3 O/G MCBs, 63A(10kA), FP 8.00 Nos. 730.00
4 O/G MCBs, 40A(10kA), FP 8.00 Nos. 662.00
5 O/G MCBs, 32A(10kA), FP 6.00 Nos. 590.00
6 O/G MCBs, 25A(10kA), FP 6.00 Nos. 590.00
7 O/G MCBs, 16A(10kA), FP 2.00 Nos. 590.00
Rotary Handle with all accessories.
100A-125A Rotary Handle with all
11 250A Cu. Busbars 1.00 RMT. 4861.00
12 125A Cu. Busbars 1.00 RMT. 3171.00
13 100A Cu. Busbars 1.95 RMT. 1942.00
14 Voltmeter 1.00 Nos. 1263.00
15 Ammeter 1.00 Nos. 1543.00
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
16 Voltmeter Selector Switch 1.00 Nos. 314.00
17 Ammeter Selector Switch 1.00 Nos. 314.00
18 Energy Meter 1.00 Nos. 2670.00
19 SP MCBs, 6A(10kA), SP 8.00 Nos. 111.00
21 Indicating Lamps 12.00 Nos. 43.00
Supplying and erecting, commissioning and
testing of Diesel Generating set confirming
to IS: 4722:1968 & BS:5514 having
continuous rating, 3 phase, 415 volts,
cycles A.C. supply comprising of a totally
enclosed air/water cooled diesel engine with
multi-cylinders developing suitable BHP not
less than following capacity at 1500 RPM
with 10% overload for one hour in 24 hours
with standard accessories like fly wheel,
lubricating oil cooler, "A" class governor,
heavy duty fuel wheel and lubricating oil
filter, oil bath air filler, lubricating oil
pressure gauge, end exhaust manifold,
standard set of tools with adjustable
spanners, screw drivers, cylinder head to
cover, joint cylinder head to exhaust, element
lube oil filter, 12 / 24 volts electric starting
equipment complete with standard heavy
duty battery, dynamo, cut-outs, ammeter,
necessary wiring, pressure gauge, starter etc
and heavy duty Residential type exhaust
silencer (With DEF System) and vertical hot
logged with asbestos rope, save oil trays,
exhaust piping of required length, standard
wall/floor mounted fuel with level indicator
and piping and drip proof alternator, self
excited, self regulated, screen protected, with
excitation system, capable of delivering the
rated system output at 415 volts, 3 phase,
PF, 50 Hz, 4 wire, running at 1500 RPM,
conforming to IS-4722- 1968 with voltage
regulation +/- 5% of rated voltage from no
load to full load. Both the engine and
alternator fitted on a common fabricated
steel base plate with antivibration mounting
engine and alternator both connected to
each other by flexible flange coupling and
with floor/wall mounted control panel box
comprising of voltmeter ammeter, selector
switches, ACB / MCCB / MCB of adequate
indicator lamps duly wired with HRC fuses.
The alternator & control panel shall be
connected with provided suitable capacity
armoured cable and complete with Acoustic
enclosure (canopy) made out of 16 SWG
CRCA Sheet, sound absorbing material
Rockwool of 64 density & 100 mm thick
conforming to IS:8183 / PU Foam of
Density - at least 40 mm. The resin bonded
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
rockwool covered from inside the canopy by
perforated sheet with 3/4 mm holes, sound
level not more than 75 dB at a distance of
mtr, as per PVCT norms.DG set should have
in built fuel tank capacity of minimum 8 hrs
of continous running capacity on full load .
Erection, commissioning and satisfactory
testing as per requirement with first filling of
fuel (minimum up to the 80% of fuel tank
capacity), oil, etc. with guarantee /
Warrantee of complete system for Two
years. & with obtaining all necessary
certificate from Electrical Inspector. The
Capacity and Ratings of DG sets are as below.
(As per new CPCB4+ Emission norms
Engine With - Turbo Charger, EGR (Exhaust
Gas Recirculation), CRS (Common Rail Fuel
System), DOC (Diesel Oxidation Catalyst),
SCR (Selective Catalytic Reduction),
Integrated wiring harness connected to ECU
(M) Continuous rating of 125 KVA ,BHP not
less than 154 BHP
Providing & erecting approved make AMF
control panel suitable for following size of
phase, 415 V., 50 cycles, A.C. diesel
generating set complete of scope as detailed
1) Power module: A pair of
electromechanically interlocked contactors
(for mains & generator) Overload relay for
generator contactor Neutral contactor for
mains and generator Power socket for
2) Control and metering module: Line
voltage monitor. Generator voltage monitor
Ammeter 3 items attempt start facility. Air
circuit breakers/MCB/MCCB of suitable
rating for auto/manual operation.
Auto/manual switch. Emergency stop push
buttons. Manual start push button. frequency
meter. Engine hour meter. Two earthing
3) Protection module: The engine shutdown
in the unlikely event of Low lube oil pressure
High cylinder head temperature. V belt
4) Indicators with alarm Load on generator.
5) Indicators Load on mains Engine fails to
start . Emergency stop battery charger.
The AMF Panel of following capacity
(C) AMF Control Panel for100 KVA/125 KVA
Design, Supplying, installing, testing of
factory fabricated ready made Three phase
APFC Panel Cubical Panel fabrication should
be type tested as per IEC 61921, 61439:1&2
Capacitor Duty Contactor for switching as
per following Steps Incomer Switch of MCCB
type Icu=Ics=50KA at 400/440 Volts, with
OC, SC, internal earth fault protection
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Incomer Switch of MCCB type Icu=Ics=50 KA
at 400/440 Volts, with OC, SC, internal earth
fault protection,Copper tinned insulated
Busbar,Cubical panel should be indoor type
with IP 43 and IK 10,Metalized
polypropylene film type 3-phase 550 Volt
Capacitor,De tuning Reactor for each
capacitor,Panel having Short Circuit and
Overload protection,Each step Capacitor
having suitable MCB with Sc, OL, internal
earth fault relay,Each stage having Stage
Contactor (Capacitor load rating),PF
regulator master controller having suitable
steps with LCD display, Rs
Communication port, Indication LED Lamps
for main incomer and ON-OFF for each
capacitor bank,MS Chanel for Floor
mounting, Cable entry as per site situation,
Cooling fans for panel
Providing and erecting Approved make Four
pole moulded case circuit breaker having
breaking capacity ICU of 35 KA. at 415 V.
having normal current rating 125A. with
Fixed thermal & magnetic release suitable to
work on A.C.supply 50 c/s. with all internal
connections, spreader tinned copper &
complete erected in existing 16 G.M.S.
ICS=100% of ICU only (Cat III)
Providing and erecting Approved make Four
pole moulded case circuit breaker having
breaking capacity ICU of 35 KA. at 415 V.
having normal current rating 250A. with
Fixed thermal & magnetic release suitable to
work on A.C.supply 50 c/s. with all internal
connections, spreader tinned copper &
complete erected in existing 16 G.M.S.
ICS=100% of ICU only (Cat III)
Providing and erecting Approved make Four
pole moulded case circuit breaker having
breaking capacity ICU of 50 KA and above at
415 V having Normal current rating 400A.
199 with variable Thermal & magnetic release 1.00 Nos. 24979.00
suitable to work on A.C.supply 50 c/s. With
all internal connections, spreader tinned
copper & complete erected in existing
G.M.S. housing.
Providing and erecting Approved make Earth
fault Relay suitable to mount with inter
connection suitable to following size of
moulded case circuit breaker having CT ratio
& MCCB rating as following along with shunt
trip 220V AC. with all internal connections &
complete erected in existing M.S.housing. (3)
250 A -400 A , CT Ratio 1/400
Providing and erecting Sheet Steel powder
coated MCB distribution board - flush /
surface mounted fitted with busbar, neutral
link, earth bar and DIN rail, confirming to IS
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
13032 and BS 5486-1986 without MCB to
house appropriate nos. of MCBs.(The DBs
should be used of same company of MCB to
be used) Three phase 12 way SS Double door
for horizontal single phase outgoing
Providing and erecting Sheet Steel powder
coated MCB distribution board - flush /
surface mounted fitted with busbar, neutral
link, earth bar and DIN rail, confirming to IS
202 13032 and BS 5486-1986 without MCB to 8.00 Nos. 3379.00
house appropriate nos. of MCBs.(The DBs
should be used of same company of MCB to
be used). Three phase 8 way SS Double door
for horizontal single phase outgoing.
Providing and erecting Sheet Steel powder
coated MCB distribution board - flush /
surface mounted fitted with busbar, neutral
link, earth bar and DIN rail, confirming to IS
203 13032 and BS 5486-1986 without MCB to 2.00 Nos. 1478.00
house appropriate nos. of MCBs.(The DBs
should be used of same company of MCB to
be used). Single phase 12 way SS Double door
for horizontal single phase outgoing
Miniature circuit breaker single pole 6A to
32A suitable to operate on 240 V A.C. system
204 and having breaking capacity 10 KA to be 322.00 Nos. 111.00
erected in existing box. confirming to IS
8828/1996 with ISI Mark - SP MCB CAT-lll
Approved make ELCBs / RCCBs conforming
to IS: 12640 and having sensitivity of 30 mA
and Short Circuit withstand capacity of 6 KA
and suitable for operation on single phase
205 240 V. having characteristic of quick action & 14.00 Nos. 1950.00
tripping with all advance feature & do not
incorporate any electronic component. for
following Max. rating erected as directed
Amps.DP CAT-lll
Approved make ELCBs / RCCBs conforming
to IS: 12640 and having sensitivity of 30 mA
and Short Circuit withstand capacity of 6 KA
and suitable for operation on single phase
206 240 V. having characteristic of quick action & 29.00 Nos. 2213.00
tripping with all advance feature & do not
incorporate any electronic component. for
following Max. rating erected as directed
Amps.DP. CAT-lll
Approved make ELCBs / RCCBs conforming
to IS: 12640 and having sensitivity of 30 mA
and Short Circuit withstand capacity of 6 KA
and suitable for operation on single phase
207 240 V. having characteristic of quick action & 7.00 Nos. 2628.00
tripping with all advance feature & do not
incorporate any electronic component. for
following Max. rating erected as directed
Amps.DP CAT-lll
Supplying & erecting approved make RCCB +
MCB (Electro magnetic type only) working
208 on residual current device having 10 KA 4.00 Nos. 1925.00
short circuit breaking capacity and
mAmp. Sensitivity & 30 mili sec. tripping
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
time conforming to IS 12640 test knob
facility trip free mechanism operating for
rated leakage at nominal ten volt, complete
erected including all materials lugs screws
etc. completed.
[b] 32A / 40A, 2 pole Single Phase Cat. II
Supplying & erecting approved make RCCB +
MCB (Electro magnetic type only) working
on residual current device having 10 KA
short circuit breaking capacity and
mAmp. Sensitivity & 30 mili sec. tripping
209 time conforming to IS 12640 test knob 1.00 Nos. 2315.00
facility trip free mechanism operating for
rated leakage at nominal ten volt, complete
erected including all materials lugs screws
etc. completed.
[c] 63A, 2 pole Single Phase Cat. II
Supplying & erecting approved make RCCB +
MCB (Electro magnetic type only) working
on residual current device having 10 KA
short circuit breaking capacity and
mAmp. Sensitivity & 30 mili sec. tripping
210 time conforming to IS 12640 test knob 4.00 Nos. 2145.00
facility trip free mechanism operating for
rated leakage at nominal ten volt, complete
erected including all materials lugs screws
etc. completed.
[e] 32A to 40 A, 4 Pole Three Phase Cat. II
Sheets steel powder coated enclosure
211 suitable for incorporating One/Two nos. 8.00 Nos. 175.00
Providing & erecting 415 V MCB Four Pole
for Motor & Inductive Load (C Curve) having
212 10KA breaking capacity & confirms to IS 6.00 Nos. 590.00
:8828 in existing box having following
capacity 6 to 32 Amp. CAT-lll
Providing & erecting 415 V MCB Four Pole
for Motor & Inductive Load (C Curve) having
213 10KA breaking capacity & confirms to IS 14.00 Nos. 590.00
:8828 in existing box having following
capacity 6 to 32 Amp. CAT-lll
Providing & erecting 415 V MCB Four Pole
for Motor & Inductive Load (C Curve) having
214 10KA breaking capacity & confirms to IS 6.00 Nos. 730.00
:8828 in existing box having following
capacity 63 Amp.
Providing and erecting metallic vitrified
215 danger notice board for MEDIUM VOLTAGE 20.00 Nos. 69.00
installation to be erected as per IS.
Supplying & erecting approved make Digital
time switch having lithium cell 6 years
operative and operate battery backup
channel day clock with 14 memory
programme, suitable to operate on 240V +
5%, 16A with, floating contacts Minimum
switching setup time 1 minimum & LCD
display. Also comprised permanent ON/OFF
switching. Programming switches & housed
in fire proof thermoplastic enclosure &
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
transparent cover erected as required with
necessary connection erected as directed.
Providing and erecting approved make light
control unit suitable to operate on 230V
+20% having ON/OFF delay time of 30-50
217 seconds and having facility for Auto/manual 1.00 Nos. 2243.00
system having two LDR lens to intensity light
having capacity of 5A complete erected on
section pillar with pipe and stand.
Supplying & erecting power contactor ,AC3
duty for time switch complete erected as per
direction Cat III
(D) 4 pole 440V 40 Amp.
Making trench in soft soil of suitable width of
90 cms deep for laying cable or locating the
fault all over the run and backfilling the same
and making the surface as normal ground.
Covering of cable with second class bricks or
cement tiles laid cover the cable crosswise &
220 also on both sides with covering of 7. 5 Cms. 50.00 Rmt. 139.00
layer of sand above & below cable (16 bricks
Providing and erecting XLPE(IS:7098)(I)-88
ISI armoured cable multistrand Copper
conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe
at road crossing or floor of following size of
cables.(a) 4 core 2.5 Sq. mm
Providing and erecting XLPE(IS:7098)(I)-88
ISI armoured cable multistrand Copper
conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe
at road crossing or floor of following size of
cables.(a) 4 core 4.0 Sq. mm
Providing and erecting XLPE(IS:7098)(I)-88
ISI armoured cable multistrand Copper
conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe
at road crossing or floor of following size of
cables.(a-1) 4 core 6 Sq. mm
Providing and erecting XLPE (IS:7098)(I)-88
ISI armoured cable multistrand Aluminium
conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe
of following size of cables(c) 4 core 10 Sq.
Providing and erecting XLPE (IS:7098)(I)-88
ISI armoured cable multistrand Aluminium
conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe
of following size of cables. (A) 4 core 16 Sq.
Providing and erecting XLPE (IS:7098)(I)-88
ISI armoured cable multistrand Aluminium
conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe
of following size of cables
(B) 4 core 25 Sq. mm
Providing and erecting XLPE (IS:7098)(I)-88
ISI armoured cable multistrand Aluminium
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe
of following size of cables
(D) 3 1/2 core 70 Sq. mm (35 Sq. mm 1/2
Providing and erecting XLPE (IS:7098)(I)-88
ISI armoured cable multistrand Aluminium
conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe
of following size of cables
(h) 3.5 core 185 Sq. mm
Providing and, fixing heavy duty flange type
brass cable gland with rubber ring for PVC
insulated armoured cable complete with out
going tails, insulating tape etc for following
size of cables.
Solderless crimping type Copper lugs
229 conforming to IS suitable for cable of 8.00 Nos. 65.00
following size evenly crimped with high
pressure tool & connected to switchgear
terminals with brass/cadmium plated nut
bolts in an approved manner.
(E) 4 core 4 Sq. mm / 4 core 2.5 Sq. mm / /
4 core 1.5 Sq. mm
Providing and, fixing heavy duty flange type
brass cable gland with rubber ring for PVC
insulated armoured cable complete with out
going tails, insulating tape etc for following
size of cables.
Solderless crimping type Copper lugs
conforming to IS suitable for cable of
following size evenly crimped with high
pressure tool & connected to switchgear
terminals with brass/cadmium plated nut
bolts in an approved manner.
(E) 4 core 6 Sq. mm
Providing and, fixing heavy duty flange type
brass cable gland with rubber ring for PVC
insulated armoured cable complete with out
going tails, insulating tape etc for following
size of cables. Solderless crimping type
231 Aluminium lugs conforming to IS suitable for 4.00 Nos. 78.00
cable of following size evenly crimped with
high pressure tool & connected to switchgear
terminals with brass/cadmium plated nut
bolts in an approved manner.
(E) 4 core 10 Sq. mm
Providing and, fixing heavy duty flange type
brass cable gland with rubber ring for PVC
insulated armoured cable complete with out
going tails, insulating tape etc for following
size of cables. Solderless crimping type
232 Aluminium lugs conforming to IS suitable for 20.00 Nos. 95.00
cable of following size evenly crimped with
high pressure tool & connected to switchgear
terminals with brass/cadmium plated nut
bolts in an approved manner.
(E) 4 core 16 Sq. mm
Providing and, fixing heavy duty flange type
233 brass cable gland with rubber ring for PVC 4.00 Nos. 107.00
insulated armoured cable complete with out
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
going tails, insulating tape etc for following
size of cables. Solderless crimping type
Aluminium lugs conforming to IS suitable for
cable of following size evenly crimped with
high pressure tool & connected to switchgear
terminals with brass/cadmium plated nut
bolts in an approved manner.
(E) 4 core 25 Sq. mm
Providing and, fixing heavy duty flange type
brass cable gland with rubber ring for PVC
insulated armoured cable complete with out
going tails, insulating tape etc for following
size of cables. Solderless crimping type
234 Aluminium lugs conforming to IS suitable for 4.00 Nos. 202.00
cable of following size evenly crimped with
high pressure tool & connected to switchgear
terminals with brass/cadmium plated nut
bolts in an approved manner.
(C) 3 & 1/2 core 70 Sq. mm
Providing and, fixing heavy duty flange type
brass cable gland with rubber ring for PVC
insulated armoured cable complete with out
going tails, insulating tape etc for following
size of cables. Solderless crimping type
235 Aluminium lugs conforming to IS suitable for 14.00 Nos. 556.00
cable of following size evenly crimped with
high pressure tool & connected to switchgear
terminals with brass/cadmium plated nut
bolts in an approved manner.
(E) 3.5core 185 Sq. mm
Providing and fixing approved make
Perforated C type cable tray. Made from
sheet steel. The cable tray should be single or
double bended as per required and as per IS
2062/1079 and shall be coated with hot dip
galvanizing as per IS 2629/4759. with max
17.5% perforation with coupler plate / Fish
plate and GI hardware like nut - bolt and
washers etc. erection with necessary
support( included) as per Specification and
as per instruction of engineer in charge.(4)
200 X 50 X 1.6 mm Thick.
Providing and fixing approved make
Perforated C type cable tray. Made from
sheet steel. The cable tray should be single or
double bended as per required and as per IS
2062/1079 and shall be coated with hot dip
galvanizing as per IS 2629/4759. with max
17.5% perforation with coupler plate / Fish
plate and GI hardware like nut - bolt and
washers etc. erection with necessary
support( included) as per Specification and
as per instruction of engineer in charge..(5)
300 X 50 X 2.0 mm Thick.
Point wiring for modular Light Point / Bell
with 2-1.5 sq.mm & earthwire of 1.5 sq.mm
(Green) both are of ISI marked 1.1 KV grade
238 FRLS PVC insulated multistrand copper 282.00 Nos. 445.00
wires, in following type of pipe to be erected
concealed in/ on surface on wall/ceiling
complete with 6A Modular type switch / bell
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
push & accessories and earth continuity of
following type, erected on PVC / Metallic box,
single mounting base frame covered with
textured/metallic front plate modules
erected on / in wall / ceiling as per pipe
erected, with necessary Lamp holder/ceiling
rose / H.D.Connector as directed.with
medium class Rigid PVC pipe and
Mains with 1.1 KV grade FRLS PVC insulated
ISI marked stranded Copper conductor wire
in following type of pipe to be erected
concealed in /flushed on wall/ceiling, with
239 1.5 sq. mm copper conductor FRLS PVC 2768.00 Rmt. 82.00
insulated stranded wire of green colour for
earth continuity of following size in (a) with
medium class Rigid PVC pipe and accessories
Wire : (C) 3 wire 1.5 sq. mm
Additional Wire : Mains with 1.1 KV grade
FRLS PVC insulated ISI marked stranded
Copper conductor wire in following type of
pipe to be erected concealed in /flushed on
wall/ceiling, with 1.5 sq. mm copper
conductor FRLS PVC insulated stranded wire
of green colour for earth continuity of
following size in (a) with medium class Rigid
PVC pipe and accessories
Wire : (D) 3 wire 2.5 sq. mm
Point wiring for modular secondary light
point with 2-1.5 sq.mm & earthwire of
sq.mm (green) both are of ISI marked 1.1 KV
grade FRLS PVC insulated multistrand
copper wires, in following type of pipe to be
erected concealed in / flushed on
wall/ceiling, complete with earth continuity
241 and necessary connection with primary light 194.00 Nos. 131.00
with accessories erected on Metal / PVC box
covered with 3 mm thick PC(Polycarbonet) /
Acrylic sheet for open / concealed wiring.
with necessary Lamp holder / ceiling rose /
H.D.Connector as directed.
(a) with medium class Rigid PVC pipe and
Point wiring for modular Two Way
Controlled Light Point with 2-1.5 sq.mm &
earthwire of 1.5 sq.mm (green) both are of
.ISI marked 1.1 KV grade FRLS PVC insulated
multistrand copper wires, in following type
of pipe to be erected concealed in / flushed
on wall/ceiling ,complete with 6A Modular
type switches and following type of
accessories erected on PVC / Metallic box,
single mounting base frame covered with
textured / metallic front plate modules
erected on / in wall / ceiling as per pipe
erected. with necessary batten/angle holder
or ceiling rose or H.D.Connector as directed.
(a) with medium class Rigid PVC pipe and
accessories. CAT-III
Point wiring for FAN with 2-1.5 sq.mm &
earthwire of 1.5 sq.mm (Green) both are of
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
.ISI marked 1.1 KV Grade FRLS PVC insulated
multistrand copper wires, in following type
of pipe to be erected concealed in / flushed
on wall/ceiling complete with 6A Modular
type switch and hum free EME four or more
step type electronic fan regulator with
separately mounted and accessories with
earth continuity of following type erected on
PVC / Metallic box, single mounting base
frame covered with textured/metallic front
plate modules erected on / in wall / ceiling as
per pipe erected. with necessary ceiling rose
/ H.D.Connector as directed.
(a) with medium class Rigid PVC pipe and
accessories. CAT-III
Point wiring for Looped Plug with 6A
Modular type switch & 5 pin socket erected
on PVC / Metallic box, single mounting base
frame covered with textured / metallic front
plate modules erected on / in wall / ceiling
with following type accessories.
Do - As - Above but for 6 A x 5 pin 250 Volt
switched socket outlet point at convenient
location. ( Plug & Switch can be together or at
different location).
Point wiring for Individual Plug with &
earthwire of 1.5 sq.mm (Green) both are of
ISI marked 1.1 KV grade FRLS PVC insulated
multistrand copper wires, in following type
of to be erected concealed in / on surface of
wall / ceiling complete with Modular type
switch & 5 pin Plug erected on PVC / Metallic
246 box covered with appropriate front plate 128.00 Nos. 704.00
modules erected on / in wall / ceiling as per
pipe erected with following type of
[II] For 6/16A Plug with 2-2.5 sq.mm Cu.
(a) with medium class Rigid PVC pipe and
Providing & erecting Switch board for
Computer or electric apparatus consisting of
following modular type accessories mounted
with PVC / Metallic concealed/open box
with single mounting base frame covered
with textured/metallic /white front
247 plate,modules erected with necessary 26.00 Nos. 1122.00
connections as directed.
1 no. 6A/16A universal plug-switch
3 nos. 6A Switch
3 nos. 6A 5 pin Plug (SOR 2025-26 - 1-6-2-B
Supplying & erecting Electronic Type
Cordless Call Bell erected on PVC/Metal
248 board having portable bell push working on 5.00 Nos. 248.00
D.C. & bell on 230V A.C. supply with cells /
Providing and erecting 1.6 - 1.8 mm thick FIA
249 approved and ISI mark (embossed) RIGID 100.00 Rmt. 33.00
PVC PIPES of following size complete erected
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
with necessary PVC fittings & Junction boxes
fixed with adhesive solution & Clamps with
following type of erection.2) For erecting
concealed in RCC / Brick wall/slab or Open
along with continuous fish wire to draw
mains, laid in approved manner with
plastering by cement mortar & finishing the
surface to match the wall/ceiling.
Supply and laying of 25 mm rigid PVC pipe of
1.6-1.8 mm thickness.
Providing and erecting 1.6 - 1.8 mm thick FIA
approved and ISI mark (embossed) RIGID
PVC PIPES of following size complete erected
with necessary PVC fittings & Junction boxes
fixed with adhesive solution & Clamps with
following type of erection.2) For erecting
250 concealed in RCC / Brick wall/slab or Open 50.00 Rmt. 54.00
along with continuous fish wire to draw
mains, laid in approved manner with
plastering by cement mortar & finishing the
surface to match the wall/ceiling.
Supply and laying of 32 mm rigid PVC pipe of
1.6-1.8 mm thickness.
Providing and erecting 1.6 - 1.8 mm thick FIA
approved and ISI mark (embossed) RIGID
PVC PIPES of following size complete erected
with necessary PVC fittings & Junction boxes
fixed with adhesive solution & Clamps with
following type of erection.2) For erecting
251 concealed in RCC / Brick wall/slab or Open 20.00 Rmt. 67.00
along with continuous fish wire to draw
mains, laid in approved manner with
plastering by cement mortar & finishing the
surface to match the wall/ceiling.
Supply and laying of 40 mm rigid PVC pipe of
1.6-1.8 mm thickness.
Providing & laying approved make Double
walled corrugated pipes (DWC) of
polyethylene(conforming to IS 14930 II
)with necessary connecting accessories of
same material at required depth in existing
trench for laying of cable. below ground /
road surface for enclosing cable
(A)50 mm outer dia.
Providing & laying approved make Double
walled corrugated pipes (DWC) of
polyethylene(conforming to IS 14930 II
)with necessary connecting accessories of
same material at required depth in existing
trench for laying of cable. below ground /
road surface for enclosing cable
(B)63 mm outer dia
Providing & laying approved make Double
walled corrugated pipes (DWC) of
polyethylene(conforming to IS 14930 II
)with necessary connecting accessories of
same material at required depth in existing
trench for laying of cable. below ground /
road surface for enclosing cable
(C) 90 mm outer dia.
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Supplying and erecting Flexible PVC
insulated multistrand multicore 1.1 kv grade
255 ISI marked copper wires of following size to 100.00 Rmt. 46.00
be erected as directed.
e) 1.50 Sq.mm 3 core round PVC sheathed
Supplying and erecting Flexible PVC
insulated multistrand multicore 1.1 kv grade
256 ISI marked copper wires of following size to 50.00 Rmt. 77.00
be erected as directed.
h) 2.50 Sq.mm 3 core round PVC sheathed.
Supplying and erecting Flexible PVC
insulated multistrand multicore 1.1 kv grade
257 ISI marked copper wires of following size to 75.00 Rmt. 106.00
be erected as directed.
i) 2.50 Sq.mm 4 core round PVC sheathed.
Supplying and erecting Flexible PVC
insulated multi strand multi core 1.1 kv
258 grade ISI marked copper wires of following 50.00 Rmt. 126.00
size to be erected as directed.
j) 4.00 Sq.mm 3 core round PVC sheathed.
Supplying and erecting Flexible PVC
insulated multi strand multi core 1.1 kv
259 grade ISI marked copper wires of following 75.00 Rmt. 175.00
size to be erected as directed.
K) 4.00 Sq.mm 4 core round PVC sheathed.
Mains with 1.1 KV grade FRLS PVC insulated
ISI marked stranded Copper conductor wire
in following type of pipe to be erected in / on
260 wall / ceiling with following sq. mm copper 10.00 Rmt. 179.00
conductor FRLS PVC insulated stranded wire
of green colour for earth continuity of
following size : 4 wire 4 sq. mm.
Mains with 1.1 KV grade FRLS PVC insulated
ISI marked stranded Copper conductor wire
in following type of pipe to be erected in / on
261 wall / ceiling with following sq. mm copper 245.00 Rmt. 258.00
conductor FRLS PVC insulated stranded wire
of green colour for earth continuity of
following size : 4 wire 6 sq. mm
Supplying and erecting LED indoor fittings
with LEDs of wattage 0.2 Watt to 0.5 Watt
assembled on single MCPCB, with housing
used as a heat sink shall be made of thick
sheet Steel conforming to IS: 513/CRCA/
aluminium die cast powder coated and high
U.V. & corrosion resistance with diffuser
with company mark/name 120 to
V,Power Factor more than 0.9, THD < 10 %,
CCT 3000 K to 6500K - as per selection,
Luminaire efficacy> 110 lumens/watt ,LED
efficiency-110 lumens/watt LED driver
efficiency > 85 %
Occupany Sensor - Auto Dimaable CREE /
OSRAM / PHILIPS Lumileds / NICHIA /
SEOUL/Bridgelux make LED used for
luminaire. ( fitting required LM-79 & LM-80
Certificates)(NOTE: Below description have
shown ranges of Wattage capacity of LED
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
(iii) 18-20 Watts, Surge - 2KV,IP-20,
conventional 4 feet CAT-III
Supplying and erecting LED indoor fittings
with LEDs of wattage 0.2 Watt to 0.5 Watt
assembled on single MCPCB, with housing
used as a heat sink shall be made of thick
sheet Steel conforming to IS: 513/CRCA/
aluminium die cast powder coated and high
U.V. & corrosion resistance with diffuser
with company mark/name
120 to 300 V,Power Factor more than 0.9,
CCT 3000 K to 6500K - as per selection,
263 Luminaire efficacy> 110 lumens/watt ,LED 7.00 Nos. 218.00
efficiency-110 lumens/watt
LED driver efficiency > 85 %
CREE / OSRAM / PHILIPS Lumileds / NICHIA
/ SEOUL/Bridgelux make LED used for
luminaire. ( fitting required LM-79 & LM-80
Certificates)(NOTE: Below description have
shown ranges of Wattage capacity of LED
(A) Tube Light with integral driver - (i)
Watts, Surge-2 KV, IP-20,2 feet Cat-lll (SOR
Supplying and erecting LED indoor fittings
with LEDs of wattage 0.2 Watt to 0.5 Watt
assembled on single MCPCB, with housing
used as a heat sink shall be made of thick
sheet Steel conforming to IS:
513/CRCA/aluminium pressure die cast
powder coated and high U.V. & corrosion
resistance with diffuser housed in
aluminium casted body with company
160V to 270V,Power Factor more than 0.95,
Luminaire efficacy> 85 lumens/watt
LED driver efficiency > 85 %
( fitting required LM-79 & LM-80
Certificates)(NOTE: Below description have
shown ranges of Wattage capacity of LED
fittings.The Engineer incharge may select
any wattage capacity between the ranges
Circular shaped Surface Mount Downlight
with provision for spring loaded mounting
clips complete.IP20 - (iii) 16-20 watts, Surge-
Supplying and erecting LED indoor fittings
with LEDs of wattage 0.2 Watt to 0.5 Watt
assembled on single MCPCB, with housing
used as a heat sink shall be made of thick
sheet Steel conforming to IS:
265 513/CRCA/aluminium pressure die cast 21.00 Nos. 423.00
powder coated and high U.V. & corrosion
resistance with diffuser housed in
aluminium casted body with company
160V to 270V,Power Factor more than 0.95,
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
CCT 3000 K to 6500K,
Luminaire efficacy> 85 lumens/watt
LED driver efficiency > 85 %
( fitting required LM-79 & LM-80
Certificates)(NOTE: Below description have
shown ranges of Wattage capacity of LED
fittings.The Engineer incharge may select
any wattage capacity between the ranges
Circular shaped Surface Mount Downlight
with provision for spring loaded mounting
clips complete.IP20 - (ii) 11-15 watts, Surge-
Supplying and erecting LED indoor fittings
with LEDs of wattage 0.2 Watt to 0.5 Watt
assembled on single MCPCB, with housing
used as a heat sink shall be made of thick
sheet Steel conforming to IS:
513/CRCA/aluminium pressure die cast
powder coated and high U.V. & corrosion
resistance with diffuser housed in
aluminium casted body with company
160V to 270V,Power Factor more than 0.95,
Luminaire efficacy> 85 lumens/watt
LED driver efficiency > 85 %
( fitting required LM-79 & LM-80
Certificates)(NOTE: Below description have
shown ranges of Wattage capacity of LED
fittings.The Engineer incharge may select
any wattage capacity between the ranges
Circular shaped recessed Mount Downlight
with provision for spring loaded mounting
clips complete.IP20 - (iii) 16-20 watts, Surge-
Supplying and erecting LED indoor fittings
with LEDs of wattage 0.2 Watt to 0.5 Watt
assembled on single MCPCB, with housing
used as a heat sink shall be made of thick
sheet Steel conforming to IS:
513/CRCA/aluminium pressure die cast
powder coated and high U.V. & corrosion
resistance with diffuser housed in
aluminium casted body with company
160V to 270V,Power Factor more than 0.95,
CCT 3000 K to 6500K,
Luminaire efficacy> 85 lumens/watt
LED driver efficiency > 85 %
( fitting required LM-79 & LM-80
Certificates)(NOTE: Below description have
shown ranges of Wattage capacity of LED
fittings.The Engineer incharge may select
any wattage capacity between the ranges
Circular shaped recessed Mount Downlight
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
with provision for spring loaded mounting
clips complete.IP20 - (ii) 11-15 watts, Surge-
2 KV (SOR 2025-26 -2-15-3 A (II) CAT-III)
Supplying and erecting LED indoor fittings
with LEDs of wattage 0.2 Watt to 0.5 Watt
assembled on single MCPCB, with housing
used as a heat sink shall be made of thick
sheet Steel conforming to IS:
513/CRCA/aluminium pressure die cast
powder coated and high U.V. & corrosion
resistance with diffuser housed in
aluminium casted body with company
mark/name 160V to 270V,Power Factor
268 more than 0.95, THD < 15 %,C CT 3000 K to 11.00 Nos. 218.00
6500K, Luminaire efficacy> 85 lumens/watt,
LED driver efficiency > 85 % (fitting required
LM-79 & LM-80 Certificates)(NOTE: Below
description have shown ranges of Wattage
capacity of LED fittings.The Engineer
incharge may select any wattage capacity
between the ranges shown).Circular shaped
Surface Mount Downlight with provision for
spring loaded mounting clips complete. IP20
- (i) 5-9 watts,Surge-2 KV.
Supplying and erecting LED Flood light
fittings with High power White LEDs wattage
of 1Watt and above assembled on single
MCPCB, efficiency more than 130 lm/w and
corrosion free High pressure die cast
aluminum housing with smooth finish
powder coated and heat sink extruded
aluminium with diffuser and Polycarbonate
optics/ lenses with company mark/name
engraved or embossed 120 to 300 V,Power
Factor more than 0.95, THD < 10 %, CCT
Uniformity ratio >0.45, Luminaire efficacy>
85-90 lumens/watt . LED driver efficiency >
85 %.CREE / OSRAM / PHILIPS Lumileds /
NICHIA / SEOUL/ BridgeLux (U.S.A.) make
LED used for luminaire. ( fittings required
LM-79 & LM-80 certificates)
(B) Flood Light (IP-65), Surge -4KV,Light
must have 440VAC line supply protection. It
should withstand 48 hours for 440VAC line
(v)above 120 to 160 watts
Supply, Installation, Testing and
Commissioning of Providing & erecting
Approved make Ceiling Fan with double ball
270 bearing ISI mark with condenser A.C.230V 127.00 Nos. 2289.00
50c/s. 1200 mm. sweep complete, canopy
erected on existing hook or clamp with
Supplying and erecting 19 / 20 mm. nominal
bore Medium Class M.S. Pipe down rod
271 erected duly painted for fan complete with 152.40 Rmt. 107.00
necessary 24/ O.20, 3 core flexible wire with
Supplying & erecting approved make 230 V
50 Hz Operating Voltage low noise
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
decorative Roof Mounting Exhaust fan
having square frame and Slitted guard with
mounting accessories, necessary pipings and
(A) 300x300x200mm with 1250 RPM
Supplying & erecting single phase approved
make industrial exhaust fan suitable for
medium duty ring mounted low noise
273 operation suitable for medium duty having 16.00 Nos. 2713.00
following dia size and maximum speed in
[B] 380 mm dia 900 RPM CAT-III
Supplying & erecting earth pit of minimum
bore dia.150mm size approved make
Earthing Electrode consisting Pipe-in-Pipe
Technology as per IS 3043-1987 made of
corrosion free G.I.Pipes having Outer pipe
dia of 50mm having 80-200 Micron
galvanising, Inner pipe dia of 25 mm having
200-250 Micron galvanising, connection
terminal dia of 12mm with constant ohmic
274 value surrounded by highly conductive 8.00 Nos. 8551.00
compound with high charge dissipation
suitable for following type of applications.
(c) For Electrical Installation covering
Transformer Neutrals, Lightning arrester
Earthing, A.C.Plant & Sensitive Computer
System(like Automation, SCADA) i.e
independent Earthing in normal soil.
Length of Pipe : 3.00 mtrs
Back filling Compound :2 nos Bags of 25 Kg.
Supplying & erecting earth pit of minimum
bore dia.150mm size approved make
Earthing Electrode consisting Pipe-in-Pipe
Technology as per IS 3043-1987 made of
corrosion free G.I.Pipes having Outer pipe
dia of 50mm having 80-200 Micron
galvanising, Inner pipe dia of 25 mm having
200-250 Micron galvanising, connection
terminal dia of 12mm with constant ohmic
value surrounded by highly conductive
compound with high charge dissipation
suitable for following type of applications.
(a) For Electrical Installation up to 440V in
Length of pipe - 1 Mtr
Back filling compound - 1 Nos Bag of 15 Kg.
SITC of 14.2 mm dia 3 mtr. long Earth
electrode of High tensile steel electrode with
250 micron copper bonding & 1 bag of
Carbon fill Based environment friendly
backfill tested as per IEC 62561-7 in NABL
276 accredited Laboratory and suitable stainless 6.00 Rmt. 5933.00
Steel double sided clamp. Eco Friendly rust
proof heavy duty weather proof
Polyethylene Earth Pit Chamber with
following dimensions :254 mm dia (top),
mm dia (bottom) & 260 mm (height).
SITC of Galvanized Steel Flat 25x6 mm
277 thickness from earth electrode directly in 100.00 Rmt. 153.00
ground as required. Zinc coating: 500 g/m
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
square (Approx:70 micron coating) tested
and used exclusively for lightning protection
earthing system and ring equipotential
Providing and erecting required size HOT
deep Galvanised iron strip for earthing of
H.T. , OCB/ ACB/ Transformer LT panel
board, Motors etc. using proper clamp.
Providing following type of Modular Type
Accessories mounted with pvc / metallic box,
single mounting base frame covered with
279 textured / metallic front plate , modules 31.00 Nos. 159.00
erected with necessary connection.
(8) Modem Jack for Computer Open RJ-45 -
Supplying & erecting approved make LAN
280 cable of following size in existing pipe as per 1085.00 Rmt. 47.00
direction : [C] CAT -
Providing and erecting 1.6 - 1.8 mm thick FIA
approved and ISI mark (embossed) RIGID
PVC PIPES of following size complete erected
with necessary PVC fittings & Junction boxes
fixed with adhesive solution & Clamps with
following type of erection.2) For erecting
281 concealed in RCC / Brick wall/slab or Open 1190.00 Rmt. 33.00
along with continuous fish wire to draw
mains, laid in approved manner with
plastering by cement mortar & finishing the
surface to match the wall/ceiling.
Supply and laying of 25 mm rigid PVC pipe of
1.6-1.8 mm thickness.
Supplying & erecting approved make LAN
282 cable of following size in existing pipe as per 1190.00 Rmt. 47.00
direction : [C] CAT -
Supply, Installation, Testing and
Comissioning of 4 MP
Fixed Lens Dome Type Camera,H.265 4MP IR
Vandal Proof Dome N/W Camera,
30M IR, Micro SD, DC12V/PoE, IP67/IK10,
AGC ON; Defog, True day/night, Digital WDR,
DNR, HLC & BLC, Triple streams, Smart codec
ROI, Cyber Security, Basic intelligent video
NDAA Compliance, UL, CE, FCC Certified
(Including Five year free maintenance with
Supply, Installation, Testing and
Comissioning of 4MP
Fixed Lens Bullet Type Camera,H.265 4MP IR
N/W Camera, 3.6mm / 6mm, 50M, Micro SD,
DC12V/PoE, IP67/IK10, Basic IVA, 4MP
(2560 × 1440), True day/night, Digital WDR,
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
HLC & BLC, Triple streams, Smart codec by
Cyber Security Basic intelligent video
NDAA Compliance, UL, CE, FCC Certified
(Including Five year free maintenance with
Supply, Installation, Testing and
Comissioning of
Channel Network Video Recorder (NVR),
8CH@2MP, H.264 Video Compression, HDMI,
output, up to 4 SATA interface each with max
support, bandwidth 200 mbps, CE FCC, BIS,
Operating Temp -10 deg to 50 deg C, USB and
Interface (Including Five year free
maintenance with
Supply, Installation, Testing &
Commissioning of unloaded UTP CAT6A
Gigabit Modular Patch Panel for 24 ports in
1U form factor as per the tender
specifications, with universal A/B labeling
286 and 110 connector terminations on rear of 2.00 Nos. 46120.00
panel allowing for quick and easy installation
of 23 AWG cable.- as per technical
specification etc. Approved Make :
Commscope / Uniteco/ Panduit (For Data
Supply, Installation, Testing &
Commissioning of unloaded UTP CAT6
Gigabit Modular Patch Panel for 24 ports in
1U form factor as per the tender
specifications, with universal A/B labeling
and 110 connector terminations on rear of
panel allowing for quick and easy installation
of 23 AWG cable.-Data includes Data, Voice,
CCTV, Wi-Fi as per technical specification etc.
as required. Approved Make : Commscope /
Uniteco/ Panduit (For CCTV & Access
Supply, Installation, Testing &
Commissioning of 18U (1000W X 100D)MM
Wall mount closed rack with front glass door,
fan tray on top, perforated rear doors,
keyboard tray with shelf. Casters & 2 nos
vertical power strip with std, as per technical
specification etc. as required. Approved
Make : Dlink / Uniteco/ Alpine / Valrack
Supply, Installation, Testing &
Commissioning of 9 U (600W X 600D)MM
Wall mount closed rack with front glass door,
fan tray on top, perforated rear doors,
keyboard tray with shelf. Casters & 2 nos
vertical power strip with std, as per technical
specification etc. as required. Approved
Make : Dlink / Uniteco/ Alpine / Valrack
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Supply, Installation, testing & commissioning
of 50 inch 4K UHD LED commercial signage
Display with HDMI,Wi-Fi, 350 nit, Slim
designed for easy to mount installation and
clean cable management, System on
chip ( SoC) Technology and embedded media
player provide an all-in-one digital
signage.The signage having resolution
3650x2160 ( 16:9), Connectivity /
Sound : HDMI 2.0 (3),USB 2.0 x 2,Stereo mini
290 Jack,Speaker 10W 2ch,Internal Player 1.00 Nos. 52830.00
Processor:Cortex A72 1.7GHz Quad-Core
CPU, Storage (FDM): 8GB, Features
Special:Workspace
(Microsoft365/VMWare/RDP) / Custom
Home / Auto Source Switching & Recovery /
Dicom Simulation Mode / Director Mode /
SmartView+(PC)[end of march~]
Upgradable Web-Engine / Tizen Enterprise
Platform / Smart Calibration /Smart
View+(mobile) / Video Conference Solution.
Supply, Installation testing and
commissioning of 108 cm (43 inches) FHD
Smart LED TV. Approved Make Samsung /
Sony / L.G. Resolution: FHD (1920 x 1080),
Refresh Rate: 50 Hertz, Seamlessly connect
your devices with multiple connectivity
options: Wi-Fi 5 for smooth streaming,
Bluetooth for wireless audio devices, 2 HDMI
ports (including HDMI eARC) for Set-Top
Box/DTH and high-quality soundbars,
Anynet+ (HDMI-CEC) for unified control,
USB-A for media playback and external
devices, Ethernet (LAN) for stable internet,
and RF In for cable or antenna input, Sound
Features: Powerful 20 W Sound Output |
291 Object Tracking Sound Lite | Q-Symphony | 5.00 Nos. 30000.00
Adaptive Sound, Smart TV Features: Smart
Remote with built-in Voice Assistance |
Works with Alexa/Google Assistant external
spekers| Endless Content with Samsung TV
Plus (Access 100+ free TV Channels) | Web
Browser | Quick Remote | Mobile-to-TV
Mirroring | Sound Mirroring | Wireless TV On
| Connect Apple Devices with AirPlay |
Universal Guide | Energy Rating: 5 Star |
Annual Energy Consumption: 48 kWh/Year,
Warranty Information: 1-year manufacturer
warranty and 1 year additional on Panel
from date of purchase on the television set
and 12-month warranty on the remote
Supply, Installation Testing &
Commissioning 15 Mtr. HDMI Interface
292 Cable as per the detailed Specifications 5.00 Nos. 1760.00
supports transmission of 4K Signals as per
the detailed Specifications.
Providing & Erecting approved make
following size of TV Co-axial flexible cable
comprising inner conductor of solid bare
copper insulated with Foam PE & Secondary
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
conductor made of poly - Aluminium film
bonded Al. Braids @ suitable coverage
overall sheathed with black PVC insulation.
Providing following type of Modular Type
Accessories mounted with pvc / metallic box,
single mounting base frame covered with
textured / metallic front plate , modules
erected with necessary connection. for (4)
TV Co-axial Socket outlet
SITC of Microprocessor based Net-workable
4-Zone Addressable Fire Alarm Control
Panel. The Panel shall be compliant with
EN54-2, EN54-4 and approved by LPCB. The
Fire Alarm Control Panel shall have inbuilt
loops. The Panel must have large graphic
display. The Panel must also have the
capability to take Addressable Intelligent
Wired and Wireless Devices on same loop.
Each loop shall have a capacity of
analogue Addressable devices and
127 Base sounders/Base Sounder Beacons.
The Panel shall have 240 V AC power supply
along with automatic Battery Charger.
Approved by LPCB (Including Five year free
maintenance with guarantee).
SITC of 4 Zone standalone Fire Alarm control
Panel, 16 X 2 Character LCD Display,
provision for zone wise contact and sounder.
296 Panel does not have provision to connect 1.00 Nos. 12300.00
Repeater Panel. Approval: CE
Mark.(Including Five year free maintenance
with guarantee).
SITC of Analogue Addressable Multi- Sensor
which shall be fully compatible with
Analogue Addressable Protocol,having
removable high performance chamber with
Twin fire LED's allow 360 degree viewing,
User selectable sensitivity modes 1% to
4.5% obs/m, Incorporate Optical and dual
Heat elements, lock mechanism (sensor to
base), Electronically addressed,
Pulsing/non-pulsing controlled from panel.
Approved by LPCB & VdS. (Including Five
year free maintenance with guarantee.
SITC of Analogue Addressable Multi- Heat
Sensor which is fully compatible with
Analogue Addressable Protocol,having
removable high performance chamber with
Twin fire LED's allow 360 degree viewing,
User selectable sensitivity modes 0 to
298 degree Celsius, Incorporates Fixed 6.00 Nos. 3600.00
Temperature and Rate Of Rise Heat
elements, lock mechanism (sensor to base),
Electronically addressed,
Pulsing/nonpulsing controlled from panel.
Approved by LPCB (EN54: Part 5) (Including
Five year free maintenance with guarantee).
Supplying, installation, testing &
299 commissioning of response indicator on 20.00 Nos. 150.00
surface/recessed MS Box having two LED,
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
metallic cover complete with all connections
etc as required.
SITC of Manual Call Point approved to EN54-
11:2001, Approved by LPCB Easy to install,
push-fit wiring terminals (Including Five
year free maintenance with guarantee)
SITC of Analogue addressable loop powered
Base Sounder, variable sound output 50 ~
dB(A) (±2 dB(A)) output at 1 metre, 51 user-
selectable tones (all tones EN54-3
compatible), Auto shutdown feature
prevents noise-pollution, Approved by LPCB
& VdS (Including Five year free maintenance
with guarantee)
Supplying & laying of 2 x 1.5 sqmm fire alarm
armoured cable, 600/1000V rated with
302 annealed copper conductor having XLPE 1998.00 Rmt. 122.88
insulation, steel wire armouring & FRLS
outer sheath complete as required.
Supply & laying of 4 Core X 1.5 sq.mm. FRLS
303 Armoured PVC Insulated copper cable - 120 100.00 Rmt. 210.00
MIN FIRE RATED CABLE
Providing & erecting open well type
horizontal mono block pump set with
stainless steel body having following
304 specification, (C) 1 H.P. single phase open 1.00 Nos. 9518.00
well motor pump set suitable for 185 LPM
discharge @ 25 mtr. head, suitable for 32 mm
dia. Delivery pipe with control panel.
Supplying & erecting D.C.P. type fire
extinguisher for following capacity cartridge
type with gun metal cap 150 gram CO2 gas
cartridge, powder and brackets confirming
305 to IS 2171 1985 and complete erected with 6.00 Nos. 1696.00
necessary clamps made from 50 x 6 mm M S
Flat with nuts and bolts grouted in wall
[A] For 5 Kg Capacity.
Supplying & erecting carbon dioxide (CO2)
fire extinguisher user of following capacity
with necessary clamps made from 50 x 6 mm
M.S. Flat with nut & bolts grouted in wall
[B] For 5.5 / 6.5 KG Capacity.
Providing & erecting water cooler having
storage capacity 150 Ltr. & cooling capacity
150 Ltr.per hour @ an ambient temp of 45˚ C.
The outlet temp. of the water should drop by
15˚C within a hour, The water cooler should
be comprising of hermetically sealed
compressor, fan motor, condensing unit,
water tank surrounded by evaporating, coil,
thermostats, relay etc.complete with
necessary inlet & outlet connection. The
body of water cooler will be made from
Stainless Steel.
Supplying & erecting reverse osmosis (RO)
water purification system with M.S. powder
coated pedestal frame, prefilter housing
carbon filter suitable buster DC pump, auto
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
low & high pressure switches with following
size of LPH capacity & erected as directed
with one year comprehensive maintenance
[D] 100 LPH with 1 phase / 3 phase Raw
water pump of 500LPH @ 2.5kg/cm2 - (1N0
- KBL, Groundfoss, xylem), Dual media filter
10"x54" - (1 No), Micron cartridge filter 20"
x 2.5" ( 1No), High pressure pump 500 LPH
@ 10 kg/cm2 - (1No - KBL, Groundfoss,
xylem), RO Membrane housing with RO
membrane of 40 x 40 - (1No), RO pressure
tube 4" x 1E - ( 1No), 0 - 1200 LPH Rotameter
- (2 Nos), with Recovery Rate 50%.
providing and erecting Fully Automatic
Emergency Light working on 220/250 Volts
50 C/s. AC supply complete with BATTERY of
6 volts, 18 watts Lamps Magnetic relay &
Battery charging circuit, and extra output
socket, to provide sufficient light
continuously for about 4 hours including
lamps Emergency Light immediately comes
to on by providing bright light when main
electric supply fails suddenly. And it is all
automatic, controlled by a magnetic relay. It
is portable too, can be placed at any
convenient point. (a) tube emergency light
2feet,20watt ,10AH
Supplying & erecting approved make
Automatic liquid level controller 6A. with
sensor testing as per instruction of Engineer
310 in charge on site complete with wiring 1.00 Nos. 2332.00
connection with existing wires , with copper
conductor from pump to upper and lower
Providing M-20 / 1:2:4 cement concrete
foundation & 70 % PCC from bottom
including excavation for the pole of size 45 x
45 x 100 cms. Deep in below ground level
with plinth of 45 cms x 45 cms (or 45 cms dia
x 45 cms) high upper ground level with
necessary curing and finishing in approved
manner. ( for 4 & 6 mtr pole).
Supply of approved make FRP Pole having
following specifications: FRP Light Pole
made by CNC filament winding machine
using thermoset resin polyester/epoxy resin
system) having minimum 62% glass content.
The pole should be in one piece and tapered
round in shape, having smooth finish and
should be totally free from corrosion as well
as non conductive & shock proof Pole should
be provided with FRP Anchor Base and it
should be heavy duty, or MS Material duly
painted with Epoxy paint.
[H] Overall length of 6 Mtr. Average
Thickness: 7.5mm
Top/ Bottom OD Dia A/F 89mm ± 2mm
approx. approx. Weight of Pole 32 kg approx.
(Without Base) Anchor Base (Size 300X300
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Supply of approved make FRP Pole having
following specifications: FRP Light Pole
made by CNC filament winding machine
using thermoset resin polyester/epoxy resin
system) having minimum 62% glass content.
The pole should be in one piece and tapered
round in shape, having smooth finish and
should be totally free from corrosion as well
as non conductive & shock proof Pole should
be provided with FRP Anchor Base and it
should be heavy duty, or MS Material duly
painted with Epoxy paint.
[C] Overall length of 6 Mtr. Average
Thickness: 8mm.
Top/ Bottom OD Dia A/F 114/174 mm ±
2mm approx. approx. Weight of Pole 38 kg
approx. (Without Base) Anchor Base (Size
Providing FRP arm bracket of having 2 sets
of suitable SS304 hardware for fixing the
314 brackets & spread of 1.2 Mtr (Suitable for 89 3.00 Nos. 2526.00
to 114 mm pole top dia).
(a) Single arm bracket
Providing FRP arm bracket of having 2 sets
of suitable SS304 hardware for fixing the
315 brackets & spread of 1.2 Mtr (Suitable for 89 3.00 Nos. 3895.00
to 114 mm pole top dia).
(b) Double arm bracket
Supplying and erecting LED street light /
Flood light fittings with High power White
LEDs wattage of 3 Watt and above assembled
on single MCPCB, efficiency more than
lm/w and corrosion free High pressure die
cast aluminum housing with smooth finish
powder coated and heat sink extruded
aluminium with diffuser and Polycarbonate
optics/ lenses, with toughened glass with
company mark/name engraved or embossed
160 to 270 V,Power Factor more than 0.95,
THD < 10 %, CCT 3000 K to
5700K,Uniformity ratio >0.45, Luminaire
efficacy> 100 lumens/watt . LED driver
efficiency > 85 %.( fittings required LM-79 &
LM-80 certificates)(NOTE: Below
description have shown ranges of Wattage
capacity of LED fittings.The Engineer
incharge may select any wattage capacity
between the ranges shown.)
(A) Street Light (IP-65), Surge protection -
4KV integral and ,Light must have 440VAC
line supply with over-voltage protection.
(iii) Above 60 to 90 watts
Liaoning with Torrent & Electrical Inspector,
CEIG, Hi-rise permission for getting 11KV HT
Power & Electrical inspector certification in
totality to charge the power other related
317 accessories. etc. complete. 1.00 Job 45000.00
Charges for doing liasioning work for
obtaining the necessary clearances from the
Electrical inspector/competent Authorities
for the total Electrical installation, Elevator
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Inspection, co-ordinating with various
agencies. All necessary drawings,
calculations, test certificates, etc. as required
by the seauthorities shall be prepared and
furnished by the EPCV endor. Any
modification / rectification as required by
these authorities shall be carried out by the
EPCV endor at free of cost. The fees required
to be paid to these authorities for inspection
shall be borne by Owner on production of
documentary evidences.
All Required NOC / Approval / Liasoning for
the Electrical and HVAC system in the scope
of Electrical contractor.
Providing and erecting approved make split
air-conditioning unit consisting of copper
condensing unit with fan motor, hermetically
sealed rotary compressor with accessories
etc. duly connected separately erected
evaporating unit and blower motor with its
accessories by means of extra supplied
proper insulated copper tubing,drain PVC
pipes suitable for ( cost includes powder
coated Stand, Eco Friendly green gas
charging, 15A plug top & Remote Control)
with necessary core cutting. (1)For ISEER
Range (KWH/KWH)(3.1 to 3.99) Premium
(a)For 0.8 to 1.0 Ton Capacity 2.00 Nos. 38986.00
(b) For 1.5 ton capacity 10.00 Nos. 51923.00
(c) For 1.7 to 2.0 ton capacity 4.00 Nos. 58706.00
(d) For 2.2 to 2.5 ton capacity 2.00 Nos. 68449.00
Carry out RCC / Brick masonary Core cutting-
up to 100 mm dia./200mm thick
319 Wall/beam/slab with providing PVC pipe of 25.00 Nos. 1188.00
3 mm thick inside and necessary finishing on
both ends of wall.
Supplying and installing MS angle , powder
coated / Painted standard type of wall/floor
320 stand mount for outdoor unit of split AC of
following capacity, erected with necessary
hardware materials as directed.
(A) 25mm x 25mm x 3mm thick M.S angle
suitable for upto 2 TR. Capacity of ac machine
B) 35mm x 35mm x 5mm thick M.S angle
suitable for above 2 TR to 4 TR Capacity of ac 2.00 Nos. 1496.00
Supplying and erecting insulated pair of soft
copper tubing including power and control
cable,necessary PVC drain pipes for Split AC
machine up to 4 TR capacity.
Rigid UPVC drain pipe of 10 Kg/cm2. rating
with 9 mm thick nitrile rubber insulation.
a) 25 mm Diameter Pipe. 150.00 Rmt. 87.00
b) 40 mm Diameter Pipe 50.00 Rmt. 108.00
Extending two Floors of existing MRL
323 (Gearless) stretcher lift, M.S. collapsible 1.00 Job 487500.00
Manual Door Operation Lift with
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Passengers, 884 Kgs, 1.0 Meter Per Second,
M.S. Powder Coated Finish Cabin.
Supply, installing , commissioning and
testing of Stretcher Lift ( Hospital lift ) 15/16
324 passengers (MRL LIFT) as per R & B S.O.R (
Category - Premium ) having following
specifications:- G + 3 Floor
Supplying, Erecting, Testing &
Commissioning the passenger lift having
following main features:
[1] GEAR LESS LIFT DRIVE comprising of
High Starting torque Lift 3 phase 440 V
A. C. Permanent Magnet Synchronous motor
of proper rating with high efficiency shall be
[2] Micro processor based / PLC, ACVVVF,
vector control drive with encoder feedback
closed loop system shall be used for lift car
and door operation which shall be full
collective selective operation hall call
demand response, UP/DOWN hall stops,
Main, Up/ Down Contactor with overload
and phase reversal relay and safety controls.
[3] Car with M S platform with bracings of
adequate size and to sustain the impact load
cabin + passenger with safety factor of fire
for steel and side panels of Stainless steel of
sheet of grade 304 duty. Car ceiling will be
S.S. finishes with aesthetic appearance with
LED ceiling lights. Car flooring shall be of anti
skid PVC with choice of colour of engineer in
charge. Car doors shall be of stainless steel
grade 304, hairline finish with centre
opening / telescopic automatic doors. Car
panel will also be S.S. 304 finished with
emergency stop device, mechanical door
safety device, facility of auto/ attended
mode. All car panel buttons and all floor
switches must be with brail language as per
[4] All landing doors must be fire rated for
hour shall be fully automatic centre opening/
telescopic opening made of hairline finish
steel grade of 304 with key holes and
infrared curtains with Unlocking facility
[5] Appropriate battery operated emergency
light in the car along with alarm switch shall
be provided. Also, Emergency Light & Fan
should start immediately without any Time
Delay as soon as power fails.
[6] Digital scrolling indicator system for up-
down arrow along with floor position
indicator shall be provided inside the car
and at all floors.
[7] Full height infra red curtain with multiple
/ crossing light beams shall be provided.
[8] Automatic Rescue Device (ARD) shall be
provided accordingly of passenger capacity
with Manual Rescue Operation ( Manual
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Cranking Facility).
[9] Audio visual indication in the lift car
showing over loading shall be provided such
that doors kept open till excess load is
[10] Spring buffers/PU Buffers shall be
[11] Car fan as per passenger capacity with
automatic sleep timer shall be provided.
[12] Voice annunciator with suitable music
shall be provided in lift car.
[13] Self diagnostics system for operational
and safety parameters shall be provided in
[14] Mechanical over speed governor with
governor calibration as per actual site
parameters and submission of calibration
certificate submission, door key holes in the
floor doors, fireman switch shall be provided.
[15] Lift machine hoisting arrangement in
the lift machine room and monkey ladder for
lift pit should be provided by the lift agency,
along with the other steel structure works,
foundations for the machine etc…
[16] In the hoist way fascia plate shall be
provided without any extra cost, where ever
required as / if directed by engineer in
[17] Permanent wiring with necessary safety
devices like RCCB in all circuit, Over Voltage
Under Voltage protection and THD
eliminator in circuit for lift machine room
and lift well with proper numbers of light
points, with fixtures, exhaust fan and plug
points shall be provided by the agency. Only
3 phase Power Supply shall be made
available by department in lift machine
room. Necessary Earthing as per Lift
Act/Rules shall be arranged by Lift Agency.
[18] Any civil/ electrical works for additional
and alteration in lift shaft and machine room
related to erection of lift shall be made by lift
agency without any extra cost.
(granite/marble fixing around all landing
door openings are not in lift agency’s scope.)
[19] Agency has to provide all working
drawings and documents and liaison
services for obtaining all necessary
permission from lift inspector and other
[20] acrylic transparent licence/display A4
size holder in lift car
[20A] As per statutory requirement of Govt.
Of Gujarat lift & escalator act 2000, lift
agency has to provide
1. Car top safety barricade
2. Push & talk communication system.
3. Fireman's switch operation at Ground
4. carrying out third party lift inspection
during/after lift erection and provide report
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
by third party authorized by concern
licensing authority 5.agency has to provide
third party insurance upto completion of free
maintenance period and submit the
document for the same.
[21] Car Panel Operating Buttons with floor
position indicator/buttons must be of Auto
Glow type clearly visible when view from
[22] For Physically Handicapped person Full
Length Handrails of hairline finish steel
grade of 304 should be provided at
appropriate height on the Rear & Side Wall
Panels in Lift Car.
(B) SPECIAL FEATURES DESCRIPTION OF
for PREMIUM category
1. Advanced control system dual 64 bit
embedded microprocessor with CANBUS
Serial Communication mode including
Regenerative power efficient operation,on
site programming facility, Anti nuisance, Pte-
opening, BMS/RMS with necessary online
real time monitoring system having
necessary connectivity for remote
monitoring & other suitable supporting
hardware & software devices to fulfil the
2. Floor Indication LCD Display with call
registration & brail mark with arrival gong
and hall lantern & TFT Screen in the car with
MP3 Voice Announcer.
3. CAR Panel should be Scratch resistive SS
Moonrock finish / Hair Line / Honeycomb for
car and all Doors, All landing doors must
have fire rating up to 2 hours and car door
must have multi-level crisscross beam door
4. To & fro communication system & wiring
(i.e. car , control room & guard room ) and
Each elevator are equipped with remote
monitoring system.agency has to provide
mobile app and user id and password for
monitoring 15/16 Passengers, ( Stretcher lift
)Ground plus 4 upper floor with Rated Speed
15/16 Passengers, Ground plus 3 upper
floor with Rated Speed of 1.0 m/sec.,
(C) With General PLUS ADDITIONAL
SPECIAL FEATURES attached herewith.
Comprehensive AMC for the 2-Elevators (one
Old + One New) for the 1st Year after DLP
325 (period 3.5% of Lift Initial Cost) - 1.00 Year 87170.00
Performance bank gurantee to be submit at
time of completion of work
Comprehensive AMC for the 2-Elevators (one
326 Old + One New) for the 2nd Year after DLP 1.00 Year 87170.00
(period 3.5% of Lift Initial Cost) -
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Performance bank gurantee to be submit at
time of completion of work
Comprehensive AMC for the 2-Elevators (one
Old + One New) for the 3rd Year after DLP
327 (period 4% of Lift Initial Cost) - Performance 1.00 Year 99623.00
bank gurantee to be submit at time of
completion of work
Liaoning with AMC / AUDA / Fire Dept for
the the Lift Licence and all require Approval
for getting pre-indstallation certification and
after installation getting licence
Charges for doing liasioning work for
obtaining the necessary clearances from the
competent Authorities for the total
installation, Elevator Inspection, co-
ordinating with various agencies. All
328 necessary drawings, calculations, test 2.00 Job 15000.00
certificates, etc. as required by the
seauthorities shall be prepared and
furnished by the EPCV endor. Any
modification / rectification as required by
these authorities shall be carried out by the
EPCV endor at free of cost. The fees required
to be paid to these authorities for inspection
shall be borne by Owner on production of
documentary evidences.
FIRE DETECTION, HYDRANT AND FIRE
FIGHTING SYSTEM
Design,Supply,installing,testing &
Commissioning of FIRE HYDRANT WORKS
Internal / External Hydrant
Supplying, Installation, Testing and
Commissioning of electric driven main fire
329 pump suitable for automatic operation and 1.00 Set 281332.20
consisting of following: complete in all
respect as required.
a) Horizontal type, single stage, centrifugal,
end suction pump of cast iron body & bronze
impeller with stainless steel shaft,
mechanical seal to ensure a minimum
pressure of 3.5 kg/sq. cm. at highest and
farthest outlet at specified flow of 1680 lpm
at 70 Mtr. head conforming to IS 1520.with
suitable size of footvalve confirming to IS
4038, Pressure rating PN2 , preventing entry
of foreign body to pump through suction
pipe, perfectly flat seating surfaces for good
b) Suitable HP Squirrel cage induction motor,
TEFC, suitable for opertion on 415 volts,
phase 50 Hz. AC with IP 55 class protection
for enclosure, horizontal foot mounted type
with Class - 'F' insulation, conforming to IS-
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
c) M.S. fabricated Common base plate,
coupling, coupling guard, foundation bolts
etc. as required.
d) Suitable cement concrete foundation duly
plastered with anti vibration pads.
The pump shall be capable of giving not less
than 150% discharge at ahead not less than
65% of the rated head.
Supplying, Installation, Testing and
Commissioning of electric driven
330 pressurisation pump suitable for automatic 1.00 Set 73311.61
operation and consisting of following:
complete in all respect as required
a) Horizontal type, single stage, centrifugal,
end suction pump of cast iron body and
bronze impeller with stainless steel shaft,
mechanical seal at specified flow of 180 lpm
at 56 m. head conforming to IS: 1520.with
suitable size of footvalve confirming to IS
4038, Pressure rating PN2 , preventing entry
of foreign body to pump through suction
pipe, perfectly
flat seating surfaces for good sealing.
b) Suitable HP Squirrel cage induction motor
TEFC type suitable for operation on
volts, 3 phase 50 Hz. AC with IP 55 Class of
protection for enclosure,
horizontal foot mounted type with Class F'
insulation, conforming to IS :
c) M.S. fabricated Common base plate,
flexible rubber
coupling, coupling guard, foundtion bolts etc.
d) Suitable cement concrete foundation duly
plastered with anti vibration pads.
Supplying, Installation, Testing and
Commissioning of diesel engine driven main
331 fire pump suitable for automatic operation 1.00 Set 434502.50
and consisting of following: complete in all
respect as required
a) Horizontal type, single stage, centrifugal,
end suction pump of cast iron body and
bronze impeller with stainless steel shaft,
mechanical seal to ensure a minimum
pressure of 3.5 kg/sq. cm at highest and
farthest outlet at specified flow of 1680 lpm
at 56 m. head conforming to IS
b) Suitable HP, 1500 /1800 RPM water
cooled with radiator, diesel engine
conforming to relevant BS & IS standard
complete with auto starting mechanism,
12/24 volts electric starting equipment,
AH lead acid battery with battery stand,
exhaust pipe extended upto 6 m. outside
pump house duly insulated with 50 mm thick
glass wool with 1.0 mm. thick aluminium
sheet cladding, residential silencer,
instruments and protection as per
specification, stop solenoid for auto stop in
the event of fault with audio indications,
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
painted with post office red colour etc. as
c) One 200 Ltr capacity day oil storage tank
fabricated from 3 mm thick M.S. plates. Tank
shall be provided with inlet, outlet, overflow,
air vent, drain connections, filling connection
& level indicator. Tank shall be mounted on a
suitable steel structure (Painted with 2 coats
of red oxide paint). Tank shall be provided
with two or more coats of synthetic enamel
paint outside over two coats of red oxide
d) M.S. Fabricated Common base plate,
coupling, coupling guard, foundation bolts
etc. as required.
e) Suitable cement concrete foundation duly
plastered with anti vibration pads.
FIRE CONTROL PANEL FOR Main Hydrant
332 pump and Jockey pump and Diesel Engine 1.00 Set 22910.00
pump. Fire Control Pane (Red Colour)
Fabrication, Supplying, Installation, Testing
& Commissioning of electrical control panel
of cubical construction, floor mounted type,
fabricated out of 2mm thick CRCA sheet,
compartmentalised with hinged lockable
doors, dust and vermin proof, powder coated
of approved shade after 7 tank treatement
process, cable alley, inter-connection, having
switchgears and accessories mounting and
internal wiring, earth terminals, numbering
etc. complete in all respect, suitable for main
fire pump, pressurisation pump complete as
per CPWD specification with following in
coming and Outgoings, suitable for operation
on 415V, 3 phase, 50Hz Ac Supply with
enclosure protection class IP 42 as required
:suitable for operation on 415 V, 3 phase,
HZ, AC supply with enclosure protection
class IP 42 as required.
A. Incoming Feeder:-
(i) 1 No of 160 A,35KA, 415V,FP MCCB with
Thermal-magnetic Based Releases having
O/C, S/C, E/F protection, Digital ELR
96x96mm with CBCT, FP Spreader Terminals
1 set= 8 Pcs, Extended Rotory Handle for
MCCB, 240V AC Shunt Trip coil forMCCB.
(ii) LED type indicating Lamp with suitable
rating 2 Amp SP MCB:- 1 Set (each set
comprise of R,Y,B)
(iii) Digital type 3 phase Multi function Meter
with suitable rating of MCB & 3 Nos. of single
core epoxy resin cast type
415 V, 200 Amps, FP Aluminium Busbars
with Heat shrinkable color code insulation
OUTGOINGS:-( All outgoing feeders for
pumps should have digital Ammeter with
selector switches and LED type ON,OFF,Trip
indicating Lamps )
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
1 sets - 125 A, 25kA TPN MCCB, Ics=100%
Icu, with fully automatic Star/Delta starter
suitable for 60 HP pump with overload
protection, current sensing type single phase
preventor complete with all acceessories and
internal wiring required for automatic
operation,selector switch for local/remote,
auto/manual/OFF operation
1 no.63A,16KA MCCB Ics=100%,Extended
Rotry handle with TM release having O/C &
S/C protection with 10 HP fully automatic
star/ delta starter , current sensing type,
Single Phase Preventer, ON/OFF Push Button
& LED type Indicating lamps complete with
all accessories and internal wiring required
for automatic operation, selector switch, for
local/remote, auto/manual operation
Diesel Engine Control.
Control for Diesel Engine should be
i) Auto/Manual selector switch & 3 attempt
starting device, timers and relays as
required, push buttons, start/stop in manual
ii) LED type Indication lamp for High/Low
pressure, High Water Temp and Engine ON
iii) Battery charger suitable for 12 V/24 V DC
with boost and trickle selector switch, 0-30 V
DC volt meter, 0-20 Amp DC Ammeter.
iv) All standard relays, accessories for
automatic operation of diesel engine, wiring
with 1.5 sq mm PVC insulated copper wire
between various sensors and system
controller / starter, suitable size cable for
battery charging etc. as required.
System Controller
Designing, Supply, Installation, Testing and
Commissioning of system controller to
control operation of Main Electric Fire Pump,
Diesel Pump, Pressurisation Pump, Terrace
Pump in sequence as per specification
consisting of relays, timers, sensors,
annunciation window for fault indication,
control wiring complete as specification
Providing and fixing in position the industrial
333 type pressure gauges with gun metal / brass 4.00 Set 1067.80
valves complete as required
Providing, fixing, testing & commissioning of
Pressure Switches for automation of fire
pumps. Pressure switches shall be double
334 pole single throw type suitable for single 4.00 Set 1380.36
phase supply with diaphragm.
Aluminum Enclosure with IP 66 protection
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Supplying and fixing air vessel made of
8 mm thick MS sheet, 1200 mm in height with
air release valve on top and flanged
335 connection to riser, drain arrangement with 1.00 Set 16289.29
25 mm dia gun metal wheel valve with
required accessories, pressure gauge and
paintingwith synthetic enamel paint of
approved shade as required.
Providing, laying, testing & commissioning of
'C' class heavy duty MS Pipe conforming to IS
1239 i/c fittings like elbows, tees, flanges,
tapers, nuts bolts, gaskets etc., in ground
including excavation and providing cement
concrete blocks as support, anticorrosive
treatment with coaltar/asphalt tape as
per IS 10221, refilling the trench etc. of
following sizes complete as required .( For
Providing, laying, testing & commissioning of
'C' class heavy duty MS pipe conforming to IS
3589/IS 1239 including Welding, fittings like
elbows, tees, flanges,tapers, nuts bolts,
337 gaskets etc. and fixing the pipe on the
wall/ceiling with suitable clamp/support
frame and painting with two or more coats of
synthetic enamel paint of required shade
complete as required
i) 200 mm dia. (Wall Thickness : 6.3 mm) 5.00 Rmt. 4877.68
Supplying and fixing Single headed internal /
External hydrant valve with 1 No. 63 mm dia
instantaneous FM Gunmetal/Stainless Steel
338 coupling and cast iron wheel,ISI marked,
conforming to IS 5290 (type A) with blank
Gunmetal/Stainless Steel cap and chain as
Single headed Stainless steel 12.00 Nos. 5481.25
Providing, fixing, testing and commissioning
of Wall mounting swing type first aid Fire
Hose Reel with drum, hanging bracket, 30 M
x 25 mm dia high pressure hose reel tubing
as per IS:884 with shut nozzle and ball valve
and all required accessories.
Supply, Installation, Testing and
Commissioning of Weather proof Standard
340 Fire Hose Cabinet wall mounting type (750 5.00 Nos. 4584.75
mm x 600 mm x 250 mm deep) having
Double door opening with necessary locking
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
arrangement by allan key suitable for
housing 2 no.x15 mtrs. hose pipe, 1no.
Branch pipe & nozzle spanner.Duly synthetic
enamel painted.
Providing ISI marked RRL (IS : 636, type-A)
fire hose pipe 15 meter long and 63 mm dia
with ISI marked (IS: 903) Stainless steel male
and female coupling bound and rivetted to
hose pipes with copper rivets and copper
wire complete as required.
Providing Stainless steel ISI marked 63 mm.
dia. male Instantaneous pattern short branch
pipes with 20 mm dia. Nozzle as per IS :
suitable for 10 Kg/sqcm operating pressure
and suitable for interconnections to hose
pipe coupling as required.
Supplying and fixing of fire brigade
connection of cast iron body with gun metal
343 male instantaneous inlet couplings complete
with cap and chain as reqduried for suitable
dia MS pipe connection conforming to IS
a) 2 way - 100 mm dia M.S. Pipe 1.00 Nos. 6019.64
b) 4 way - 150 mm dia M.S. Pipe 1.00 Nos. 12476.79
Providing, fixing, testing and commissioning
344 of 25 mm dia Air Release Valve and Ball Valve 1.00 Nos. 1716.10
assembly for Air release system.
Providing, fixing, testing and commissioning
345 Pressure Relieaf Valve 25mm dia with Ball 1.00 Nos. 4940.68
Supplying and fixing orifice plate made out of
6 mm thick stainless steel (Grade 304) with
orifice of required size to be fitted between
346 flange & landing valve of external and 10.00 Nos. 1179.46
internal hydrants to reduce pressure at the
outlet to the level of 3.5 kg/cm2 complete as
Supplying, fixing, testing and commissioning
of butterfly valve of PN 1.6 rating with
bronze/gunmetal seat duly ISI marked
complete with nuts, bolts, washers, gaskets
conforming to IS 13095 of following sizes as
Providing, fixing, testing and commissioning
of C.I. Dual plate Type Non-Return Valve class
PN 16 rating with fittings, flanges, nutbolts,
washers, gaskets etc.of sizes:
Providing, installation, testing and
commissioning of stainless steel Y-strainer
349 fabricated out of 1.6 mm thick stainless steel,
Grade 304, sheet with 3 mm dia holes with
stainless steel flange.
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Supply, Installation, Testing and
Commissioning of Brass. Ball Valves Body -
Forged brass ,Trim and Ball ,SS410 , Seat
SS410 and tested to 20 kg/cm2 pressure.
Threaded End with all fittings required.
Supplying and erecting Flexible PVC
insulated multistrand multicore 1.1 kv grade
ISI marked copper wires of following size to
be erected as directed.
f) 1.50 Sq.mm 4 core round PVC sheathed 125.00 Rmt. 62.71
SITC of fire pump start stop push buttons in
Supply, Installation, Testing and
Commissioning of Single action Manual Pull
Station.Shock and Vibration Resistant, pull
Down Lever Remains Down Until Reset. Shall
be Polarity Insensitive (with all mounting
accessories , complete with Junction Box for
mooting on Surface, Cable lugs at Ends, cable
compression glands, cable tags and ferruling.
Supply, Installation, Testing and
Commissioning of Conventional Sounder
cum strobe having tone settings with range
of 95dbA and field selectable 15/30/75/110
354 candelas.(with all mounting accessories, 5.00 Nos. 508.47
complete with Junction Box for mooting on
surface, cable lugs at ends, cable
compression glands, cable tags and
SITC of 4 Zone standalone Fire Alarm control
Panel, 16X2 Character LCD Display,
provision for zone wise contact and sounder.
355 Panel does not have provision to connect 1.00 Nos. 12300.00
Repeater Panel. Approval: CE
Mark.(Including Five year free maintenance
with guarantee)
Providing, fixing, testing & commissioning of
356 15mm dia quartzoid bulb type sprinklers of
rating with required accessories :
Pendent Sprinkler 68°C standard response
(K-80) UL Listed
Providing and erecting XLPE(IS:7098)(I)-88
ISI armoured cable multistrand Copper
conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe
at road crossing or floor of following size of
b) 3 core 4 sq. mm 35.00 Rmt. 281.36
e) 3 core 16 sq. mm 35.00 Rmt. 716.95
Providing and erecting XLPE(IS:7098)(I)-88
ISI armoured cable multistrand Copper
conductor for 1.1 KV. to be laid on wall with
necessary clamps or in existing trench / pipe
at road crossing or floor of following size of
d) 8 core 2.5 sq. mm. 25.00 Rmt. 311.01
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
g) 12 core 2.5 sq. mm. 25.00 Rmt. 41.17
Providing and, fixing heavy duty flange type
brass cable gland with rubber ring for PVC
359 insulated armoured cable complete with out
going tails, insulating tape etc for following
size of cables.
a) 2 to 4 Core 2.5 / 4 sq mm 10.00 Nos. 31.36
d) 2 to 4 Core 16 sq. mm. 5.00 Nos. 45.76
Solder less crimping type Copper lugs
conforming to IS suitable for cable of
following size evenly crimped with high
pressure tool & connected to switchgear
terminals with brass/cadmium plated nut
bolts in an approved manner
Providing and fixing approved make
Perforated C type cable tray. Made from
sheet steel. The cable tray should be single or
double bended as per required and as per IS
2062/1079 and shall be coated with hot dip
galvanizing as per IS 2629/4759. with max
17.5% perforation with coupler plate / Fish
plate and GI hardware like nut - bolt and
washers etc. erection with necessary
support( included) as per Specification.
a) 50 X 50 X 1.6 mm Thick 10.00 Rmt. 300.85
Supply, installation, testing and
commissioning of Chemical Earthing with UL
Certified 17.2mm Dia. X 3000mm Long
Micron-Copper bonded M.S. Rod
manufactured as per IEC 62561-2 with 25Kg
Bentonite powder plus " U " bolt rod clamp
complete with Lockable high performence
chamber suitable & tested for 5000T
capacity with SS Hardware.or
Charges of Preparing Design , Drawings
,Testing of Fire Fighting System with
363 necessary Approval from Local Fire 1.00 Nos. 67797.00
authority. Including Pre-NOC and NOC from
Fire authority. )
Providing, fixing, testing and commissioning
of below Auto Glow Signages.
Tender Document “Extension of Community Health Centre in Vastral Ward, East Zone, Ahmedabad” PRICE BID Page
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
RAW_HTML
A. TECHNICAL BID.pdf
B. PRICE BID.pdf
Download all tender documents and submit your bid