CA NO.CWE BLY/GE (E)/14 OF 2025- 2026SPECIAL REPAIRS TO BLDG NO T-14, T-24, T-27 AND T-28 OF 6 MTN DIV ORD UNIT UNDER GE (EAST) BAREILLY

Amount

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

Dismantling unframed timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed.

S&F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed.

M&L for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws on each sheet/ each support rubber lining and filling of gap with cement mortar in CM 1:4 with wall and sheet up to 6 mtr height complete all as specified and directed.

Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc. complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:6 on brick masonary wall surfaces on fair faces of brick masonry finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on brick work surfaces finished even and smooth without using extra cement including in shafts, RCC chajjas, roof projections in four stories building in patches or site requirements complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M&L for complete removal of existing treatment from old brick/concrete surface on walls and applying two coat of Oil bound distemper using roller, brushes including in patches over a coat of alkali resistant primer and including 1.50 mm thick cement based wall care putty in two layers with making the surface complete smooth by rubbing etc with minimum 6 hr interval between any two coats complete all as specified and directed.

M&L for complete removal of existing treatment on old surfaces by vacuume based sanding machine; scrapping down smoke soot, moulds, moss and efflorescent salts and greasy spots , removing nails etc, and applying two coats of exterior Acrylic emulsion any colour over one coat of exterior water based wall priming on walls with and including provision of scaffolding required for the treatment to external surfaces of building with required safety measures etc complete all as specified and directed.

M&L for preparation of old painted surfaces of steel and iron of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F Horizontal level suspended Ceiling comprising of GI Clip-in Micro perforated 600x600mm (nominal size) tiles of 120mm galvanised steel as per IS 277 (2003) suitable for architectural finishes in 0.5mm thickness as per in IS:513 (1994) in Global white colour with concealed suspension system having a bevelled edge of 3x3mm and height of 33mm on one side and 18mm on other side. Tile shall have perforated of hole diameter 2.5mm and open area 16% with linear and diagonal pitch of 5.5mm and 7.7mm respectively along with a border of 10mm. The tile shall be electrostaticalkly polyster powder coated using RoHS compliant powder having coating thickness ranging from 60-80microns. Back side of the tile shall have Soundtex fleece hot pressed mechanically for uniform bonding to achieve NRC up to 0.7 all as per manufactures instructions , complete all as specified and directed. Note : If electrical cables are running at site aand required to be relocated electric fittings on walls are required to be shifted including refixing of fan/ light fittings and other light acessarry including making good the wall surface. Shall be deemed to be included in quoted rates.

Taking down of false ceiling and refixing the same with new grids complete all as specified and directed.

Dismantling wall/ ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed.

M&L for brushing cement slurry @ 3.00 Kg per Sqm on existing concrete surface complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B0 (12.50mm graged stone aggregate) as in sub base complete all as specified and directed.

M&L for vetrified ceramic tiles 8-10 mm thick square of size exc 0.36 sqm but n exc 0.42 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick cement screed bed in cement mortar 1:6 complete all as specified and directed.

Ditto all as per item No 20 but in Vertical surfaces such as dado/ skirting including 10 mm thick rendering of cement mortar 1:4 complete all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. and including 15 mm thick screed bed of cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Ditto all as per item No 22 but in Vertical surfaces such as dado/ skirting including 10 mm thick rendering of cement mortar 1:4 complete all as specified and directed.

M&L for Granite (of any colour or any grains as approved) work with 20mm thick table rubbed and polished as in steps jambs , pillers , window cills, cooking platform and similar works including pointing in with cement using 1:2 using marbel dust and admixture of pigments to match with the shade of granite over and including 15mm thick screed bad in CM 1:6 for laying granite all as specified and directed including taking down / dismanteling of existing plaster/ stone of any type. Note : Grinate shall be best quality and shall be provided one piece and width minimum 70mm in jambs except of cooking platform whicl shall be of full width as per site including full moulding of exposed edges with polishing. The back surface of grinate shll be made rough by sprinkeling small pebbles using adehesive for bonding with bedding layer.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 Sqm each compete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but n.exc. 4 Sqm each compete all as specified and directed.

S&F 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

M&L for powder coated aluminium sliding window with anodized aluminium frame of 3 Track of size 92mmx32mmx 1.5mm thick, with sliding shutters(02 glass and 01 Wirecloth) with necessary channels (top rail, bottom rail and style of size 40mmx 18mm x1.10 mm thick) including glazing with tinted sheet glass panel 4.00mm thick and Aluminum alloy wirecloth 4mm nominal dia and avg width of aperture 1.4mm, fitted with necessary jointing cleats, glazing clips,locking device one for each shutter , rubber packing, aluminium beading, screws, rawl plugs including all necessary holes / drilling etc, complete all as specified as directed. Note : If mentioned section are not available in market, then immediate next higher section shall be provided by Contractor without any extra cost.

M&L for providing Aluminiium shutter with Powder coated frame 88.9mmx47.63mmx1.60 mm thick fixed with heavy duty aluminium hinge of size 125mm and size of shutter with top rail , middle rail and bottom rail and style of size 85 mm x 44.5 mm x 1.56 mm thick with 200 mm size powder coated 2 nos with each leaf , Heavy duty powder coated aluminium tower bolt 150mm long 2 Nos per leaf, 3 nos Heavy duty aluminium powder coated of size 125mm with each leaf including 12 mm thick both side prelaminated particle board / 5.5 mm thick glass pane in the both panel with necessary joining cleats, rubber packing, aluminium beading, screws etc complete all as specified and as directed. Note : If mentioned section are not available in market, then immediate next higher section shall be provided by Contractor without any extra cost.

S&F aluminium powder coated partitions with aluminium anodized frame of size 90mm x 44mm x 1.6 mm thick fixed with screws including panels of any 18/19mm thick decorative both side prelaminated perticle board inretior grade upto ht 1.80 mtr above tinted glass panels 5.5mm thick of ht 0.90 mtr , with necessary, jointing cleats, glazing clips, rubber packing, aluminium beading, screws etc complete all as specified and directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F 35mm thick factory made Plain, framed, softwood 2nd class panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed. (Shutters shall be brought at site without primer and got approved by Engr-in-Charge/ GE.)

S&F 35 mm thick second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive gauze, glass etc., (with sash bars) divied into into sqare and half portion panel upto middle rail and will be provided with 12mm thick pre laminated board laminated on both side and edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizess of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a) complete all as specified and directed.

S&F 100 mm MS butt hinges medium weight cold rolled mild steel compete all as specified as directed.

S&F 150 mm aluminium anodised barrel tower bolts of extruded section, ISI marked complete all as specified and directed.

S&F 150 mm extruded aluminium alloy handles, fabricated type, anodised, ISI marked complete all as specified and directed.

S&F 300 mm long Mild steel Chromium plated sliding door bolts, plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

M&L for two coats of synthetic enamel paint over one coat of pink primer on wood or wooden based surface exc. 10cm width or girth including preparation of new or previously untreated surfaces complete all as specified and directed.

S&F mild steel spring 300mm for door, ordinary rat tail rod pattern springs, including roller and roller plate including welding as required for steel frame complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tracks or wooden beeding patti complete all as specified and directed.

S&F in replacement curtain rod of CP MS 25 mm dia not less than 1.5mm thickness with chromium plated projected bracket both side as per sample fixed in position by drilling holes in walls and fixed the brackers with rawl plug and steel screw complete all as specified and directed.

M&L for 75 mm thick cement concrete type C2 (1:3:6) (40 mm graded broken stone aggregate) as in plinth protection and finish even and fair complete all as specified and directed.

M&L for Forming Construction joint 30mm deep x 10mm wide filled with sealing compound of Grade A complete all as specified and directed.

M&L for kota stone slab 16-20mm thick polished of uniform colour as in floors of landing/ passages and similar works etc including in raiser & treads of steps over and including 15mm thick cement screed 1:6 and jointed with grey cement mixed with pigment to match the shade of the slab complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over 15mm cement screed 1:6 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Taking down carefully copper/ aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings, tube light fittings etc complete and removing all retrieved materials to MES stores for segregation of serviceable /Unserviceable fitting&fixture and also making good disturbed surfaces of wall, floors etc complete all as specified and directed.

M&L concealed point wiring complete with single core FRLS PVC insulated, unsheathed, multi stranded copper conductor cables 1.5 Sqmm 1100 volts grade, with and incl 1.5 Sqmm FRLS PVC insulated, unsheathed, multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, complete wiring drawn through & including PVC Conduit (Concealed in wall/ceiling) of size 20mm dia and above (as per conductor run ) medium grade, ISI marked, incl all accessories & fittings / junction boxes / inspection covers etc, with and incl concealed Modular metal flush box of suitable size flush within wall surface, suitable for fixing of Modular cover plate, switches / sockets etc, complete all as specified and directed for the following :- Note : 1. Modular white cover plate shall be measured and paid separately 2. Rate quoted shall deemed to be inclusive of cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required complete all as specified and directed.

All as per item No 47 above, but for one 3 pin socket outlet 5 Amp on same board complete all as specified and directed.

All as per item No 47 above, but for one 3 pin socket outlet 5 Amp on independent board complete all as specified and directed.

All as per serial item No 47 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 1.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and directed.

S&F Modular Switch 1 way 16 Amps, 1 Module size complete all as specified and directed.

S&F Modular Socket 6 A, 2/3 Pin 2 Module size complete all as specified and directed.

S&F Modular Socket 6A/16 A, 5 Pin ,2 Module size complete all as specified and directed.

S&F Modular Switch 1 way 6 Amps, 1 Module complete all as specified and directed.

S&F Modular white cover plate with frame, 3 Module size complete all as specified and directed.

S&F Modular white cover plate with frame,4 Module size complete all as specified and directed.

S&F Modular white cover plate with frame, 6/8 Module size complete all as specified and directed.

S&F Modular fan regulator step type 120W - 2 module complete all as specified and directed.

S&F angular lamp holder, metal cased body of brass with back plate including 09Watt LED Bulb in batten fittings, including Plastic square box of required size complete all as specified and directed.

S&F LED Bulb 9 Watt energy efficient color temp 6500k, lumen 825lm operating voltage 180-260 Volt complete all as specified and directed.

S&F ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all as specified and directed.

S&F LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F in replacement of street light fitting bracket, 1.5 mtr long made out of galvanized iron pipe of 40 mm dia size light grade complete with and incl 02 nos MS clamp made of MS flate iron of 50 x 6 mm size with nut, bolts, washer etc with and incl two coats of aluminum paint over a coat of red oxide primer complete all as specified and directed.

S&F in replacement LED street light luminaire of 35 Watt capacity, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and incl control gear etc, with and incl making all electric connection complete all as specified and directed.

Taking down submain wiring of size 4/6 Sqmm complete all as specified and directed.

M&L for sub main wiring with 2 runs of 6 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn drawn through & PVC conduit of size 25 mm and above incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. incl taking out old wiring and conduit Note : 1. The cost of concealed conduit & accessories is deemed to be included in quoted rates. 2. The two 2 runs of 6 Sqmm wire and one run of 6 Sqmm wire will be measured as one unit.

All as per item Ser No. 68 above but wiring with 4 Sqmm (3 Runs) complete all as specified and directed.

Taking down MCB Distributing board with MCCB/MCB of any size and capacity complete all as specified and directed

S&F VTPN DB 12 way double door type IP 54 including MCCB TP 63 Modal DU 63D Amps as incomer complete all as specified and directed.

S&F sheet Metal enclosure double shutter type for DB’s 240 Volts Single Pole and Neutral 8 way with 200 Amps rated bus bar complete including wooden board of required size duly painted with matching colour paint complete all as specified and directed.

S&F sheet Metal enclosure double shutter type for DB’s 440 Volts three Pole and Neutral 4 way with 200 Amps rated bus bar complete including wooden board of required size duly painted with matching colour paint complete all as specified and directed.

S&F sheet Metal enclosure double shutter type for DB’s 240 Volts Single Pole and Neutral 12 way with 200 Amps rated bus bar complete including wooden board of required size duly painted with matching colour paint complete all as specified and directed.

S&F SPN 40 to 63 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

S&F SP 5 to 32 amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 5 of SSR 2009 Part-I and connecting to MCBDB’s earth test point all as specified or indicated including testing on completion .

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

S&F in replacement AC functionnal box modular type complete with l enclosure with a 5/3 pin 16 Amp Socket and complete with one single pole MCB 20 Amp complete all as specified and directed.

Shikhar ji Enterprises (BID ID -3359936)

Garg Construction (BID ID -3351487)

Ikrar khan & co. (BID ID -3351849)

MOHINDER SINGH AND SONS (BID ID -3351793)

M/s DS Enterprises (BID ID -3351582)

M/S Rajeev Sharma and Co. (BID ID -3348715)

UTTRAKHAND BUILDERS (BID ID -3351203)