SPECIAL REPAIRS TO BUILDING NO P 313 OF ALKAPURI AT CQA SV GE DEHU ROAD

Amount

Taking down plaster from brick wall or stone walls etc including raking out joints, hacking for key, scrubbing down with water & removing rubbish outside MD land Complete all as specified and as directed.

M & L for rendering 15mm thick in cement mortar (1:6) on fair faces of brick or concrete surfaces finished even and smooth without using extra cement all as specified and as directed.

M & L for rendering 15mm thick in cement mortar (1:4) on fair faces of brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Demolition of concrete in ground floors and paying not exceeding 15cm thick (below of above ground level) & removing rubbish outside MD land

Dismantling wall/ floor tiles incl cm bedding but not backing ,remoal rubbish off the premises & removing rubbish outside MD land

Dismantling of stone slabs of any desc or thk in floors laid and bedded in any mortar & removing outside MD land after credit for the same is recovered by the dept

Taking down or up steel water tubing 15mm dia and connections with all fittings/valves in any place, wall, roof, ceiling etc. and removal to store all as specified

All as per item No 7 above but 20mm dia

S & F galvanised iron water tubing, medium grade, including all fittings such as tees, bends, elbows, reducers, unions, clamps etc. complete fixed to wall or laid in floors for 15mm bore pipe.

All as per item No. 9 above but except material.

All as per item No. 9 above but 20mm bore.

All as per item No.11 above but except material.

Dismantling water tanks up to 500Ltr capacity and & removing outside MD land after credit for the same is recovered by the dept

Dismantling water tanks, exc 500Ltr but n. exc 1000Ltr capacity & removing outside MD land after credit for the same is recovered by the dept

M & L for preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M & L for preparation of old treated wooden surfaces of any description over 10cm girth or width, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed.

M & L for preparation of new steel surfaces of any description over 10cm girth or width, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer. Make for Item No. 15 to 17 -(a) LUXOL (Berger paint) (b) BROLAC (Johnson & Nicholson) (c) SUPERLAC (Shalimar Paints) (d) NEROLAC (Goodlass Nerolac) (e) APCOLITE (Asian Paints)

M & L applying two coats of oil bound distemper over one coat of alkali resistant primer including preparation of newly plastered surfaces of walls complete all as specified and as directed.

M & L for complete removal of existing treatment on walls using steel wire brush , sanding machine, rubbing ivory papers etc and washing, rubbing down and stopping of distempered and painted surfaces, preparing surfaces ready to receive new finish complete all as directed.

M & L for complete removal of existing treatment on ceiling using steel wire brush , sanding machine, rubbing ivory papers etc and washing, rubbing down and stopping of distempered and painted surfaces, preparing surfaces ready to receive new finish complete all as directed.

M & L for appying two coats of acrylic distemper of approved tint on wall surfaces complete all as specified and as directed.

M & L for appyling two coats of acrylic distemper of approved tint on ceiling surfaces complete all as specifie and as directed. Make for Item No. 18 to 22: "Tractor Uno" of Asian Paints / "Jadoo"of Berger Paints / Nerolac Beauty of Nerolac paints as approved by GE

M & L for applying 3 mm thick white cementitious putty on wall and making the surfaces smooth by rubbing with sand paper to achieve finished surface complete all as specified and as directed.

M & L for applying 3 mm thick white cementitious putty on ceiling and making the surfaces smooth by rubbing with sand paper to achieve finished surface complete all as specified and as directed.

M & L Cement concrete type D2,1:4:8 (40mm graded agg) 50mm thick in sub base.

M & L for double charged coloured vitrified tiles 10mm thick (square/rectangular) polished, area of EACH tile exc. 0.18 sqm but not exc. 0.36 sqm as in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles, laid over and including 20mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

M & L for double charged coloured vitrified ceramic tiles of size 10 mm thick as in vertical surface, pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles over and including 10 mm thick rendering in cement mortar (1:4) complete all as specified and as directed.

M & L Non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular)area of EACH tile exc. 0.06 sqm but not exc. 0.11 sqm, in floors etc , set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles including 15mm thick screed bed or bedding layer in CM 1:6 for floor

M & L for coloured non skid ceramic tiles of size 400mm x 400mm x 7mm thick of colour and pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles over and including 20mm thick screed bed in cement mortar (1:6) as in floors complete all as specified and as directed.

M & L glazed ceramic coloured tiles of size 450 x 300 x 7mm thick, on vertical surfaces of walls such as skirting dado etc. set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in cement mortar 1:4 complete, all as specified.

M & L for coloured tiles 300mm x 300mm x 10mm thick of make "Johnson Endura" or equivalent as approved by GE, laid over and including 20mm thick screed bed in cement mortar 1:4, jointed and tiles to be fixed by using 6mm thick spacer and filled with matching coloured Epoxy Grout complete all as specified and as directed.

M & L for coloured glazed ceramic tiles of size 600mm x 300mm x 7 to 8mm thick of colour and pattern as approved by GE, as in vertical surface, set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles over and including 10mm thick screed bed in cement mortar 1:3 including dismantling existing tiling, cement mortar bedding (but not backing), removing rubbish off the premisescomplete all as specified & directed.

M & L for coloured glazed ceramic highlighter tile of size 600mm x 300mm x 7 to 8mm thick, colour and pattern as approved by GE, as in vertical surface set and jointed in neat cement slurry using grey cement and pointed in coloured cement to match the colour of tiles over and including 10mm thick screed bed in cement mortar 1:3 etc including dismantling existing tiling, cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified & as directed. Make for Item No. 26 to 33: M/s H R Johnson/M/s Orient Bell Tiles/M/s Kajaria/M/s Somany Tiles Ltd/M/s Nitco tiles/M/s Swastik Tiles

M & L for machine cut Cuddappa stone stab 30 to 40mm thick one side polished over cement screed base 15mm thick in CM1:6 laid & jointed with grey cement slurry mood with pigment to match the shade of slab including cutting & polishing complete.

M & L for 20 mm thick Granite ( of any type ) work (table rubbed and polished ) in door , window jambs & cills, cooking platfoRMs and like in CM1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite slab including cutting & polishing complete all as specified and directed.

M & L for green marble 10 to 12 mm thick (table rubbed and polished) as in staircases skirting/ border, jointed with grey cement slurry mixed with pigment to match the shade of slab complete all as specified and as directed.

S & F in repair 25mm dia Stainless steel curtain rod with fixing brackets.

S & F in repair Stainless steel fancy type ends for 25mm curtain rod .

S & F in repair Stainless steel fancy type corner for 25mm dia curtain rod .

S & F in repairs, water tank PVC cover for 1000 ltrs and above capacity Complete all as specified and as directed.

All as per item No 40 above but up to 500 ltrs.

S & F rotational moulded Polythene (HDPE) double layer water tanks, cylindrical & vertical type 500 Litres capacity hoisted and fixed in position including provision of 20mm/15mm dia. spouts for connecting inlet, outlet, over flow and washout pipes.

All as per item No. 42 above but 1000 litres. Make for Item No. 42 & 43- (i) M/s Sintex (ii) M/s Infra (iii) M/s Ashish Plast (iv) M/s Yash Engineering Works, Pune 09422007879 (v) M/s Plasto (vi) Polycon

S & F in repairs PVC float valve high pressure with polythene float and fly nut complete, screwed for iron pipe of bore 20mm dia or brass ferrule.

S & F in repairs gunmetal globe or gate valve, with iron wheel head, screwed both ends for iron pipe of bore 20mm dia.

All as per item No. 45 above but 15mm dia.

S & F in repairs PVC low/high level flushing cristern white 10 litre capacity incl PVC inlet pipe with brass check low level full both sides alongwith PVC flush pipe 32mm dia jointed to WC and handle incl brackets fixed all as directed. (Note:- Removing existing flushing system of CI or any other quality incl brackets).

S & F in repairs plastic water closet seat cover white closed pattern with flat bottom and cover and mild steel chromium plated high in device complete

S & F in repairs Vitreous china wash basin white flat back size 550 x 400mm including , waste pipe and plug and porcelain stopper and brackets incl cutting for and pinning in ends of brackets or erecting stand along with 32mm dia CP waste coupling and PVC waste pipe complete all as directed.

S & F in repair brass chromium plated mixer for mixing hot and cold water screwed down high pressure for iron pipe of 15mm bore complete all as specified and as directed.

M & L for cast iron Nahani trap, with grating of diameter of outlet 75mm including jointing to waste pipe fixed in PCC (1:2:4) type B-1 (using 20mm graded broken stone aggregates) complete all as specified and as directed.

S & F in repairs chromium plated two way bib cock with wall flange 15mm dia Cat No. QQT 7041 of make Jaquar ‘QUEEN'S series or equivalent of make as per Appx 'A' as approved by GE all as specified and as directed.

S & F in repairs, chromium plated long body bib cock with wall flange 15mm dia Cat No. CON-107 KN of make Jaguar ‘CONTINENTAL' series or equivalent of CERA, Prayag as approved by GE complete all as specified and as directed.

S & F in repairs chromium plated single towel rail 600mm long including built in side brackets ,Cat No. AQN-7711 of make Jaquar ‘QUEEN'S Series or equivalent of make as per Appx 'A' as approved by GE all as specified and as directed.

S & F in repairs chromium plated toilet paper holder ,Cat No. AQN-7751 of make Jaquar ‘‘QUEEN'S Series or equivalent of make as per Appx 'A' as approved by GE all as specified and as directed.

S & F in repairs chromium plated soap dish ,Cat No. AQN-7731 of make Jaquar ‘QUEEN'S Series or equivalent of make as per Appx 'A' as approved by GE all as specified and as directed.

S & F in repairs chromium plated towel ring round, Cat No. AQN-7721 of make Jaquar ‘QUEEN'S Series or equivalent of make as per Appx 'A' as approved by GE all as specified and as directed.

S & F in repairs chromium plated wall mixer 3-in-1 system with provision for both hand shower and overhead shower complete with wall flange with 115mm long bend pipe, connecting legs ,Cat No. QQT-7281 of make Jaquar ‘QUEEN'S Series or equivalent of make as per Appx 'A' as approved by GE all as specified and as directed.

S & F in repairs chromium plated towel rack, 600mm long with lower hangers,Cat No. AQN-7781 of make Jaquar ‘QUEEN'S Series or equivalent of make as per Appx 'A' as approved by GE all as specified and as directed.

S & F in repair 15mm dia Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed . Make : Jaguar (Continental series ) or equivalent

S & F in repair for hand shower, chromium plated (health faucet) with 8mm dia, 1.0 metres long flexible tube and wall hook as approved by GE with chromium plated angular cock 15mm bore with stud complete all as specified and as directed.

S & F in repairs for vitreous china EWC of white colour with plastic water closet seat closed pattern with flat bottom (with MS or CP hinging device) and fixing bolts, including connection to drain or out going pipe and to PVC flusing pipe, antisyphonage pipe and all necessary fittings etc complete all as specified and as directed.

M & L PVC (SWR) floor trap with grating including jointing with solvent cement 75mm bore dia

M & L Cutting / cleaning away small trees sapling shrubs and under growth roots from brick wall, chajjas etc including taking out complete root from from inside wall / chajjas and making good surfaces in cement concrete (1:2:4) type or in CM (1:4) to match the existing surface as specifid.

S & F in repairs 12 "corner glass 8mm thick fancy type chromium plated screwed down for fixing to wall with screw all as apecified and directed.

S & F in repairs PVC connection 15mm dia 45 cm long with 02 Nos.PTMT check nuts with washer complete

S & F in repairs chromium plated brass shower rose 125x100mm dia with swivel joint all as specified

S & F in repairs chrome plated overhead shower 120mm dia round shape multi wall flow with cascade effect (ABS body chrome plated with gray face plate) with rubbit cleaning system product code OHS-CHR-1779 of make Jaquar ‘FUSION COLLECTION' Series or equivalent as approved by GE complete all as specified and as directed.

S & F in repairs 32 mm dia PVC waste pipe 60 cm long

S & F in repairs glass shelf 12" Long x 6" wide and glass 8mm thick, fixed in chromium plated frame screwed down for fixing to walls

S & F in repairs double Angular stop cock with wall flange cast copper alloy, chromium plated fancy type with long shank and cup screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed to 15mm bore GI pipe.

S & F PVC cabinet fancy type of size 460mmx360mm with looking mirror complete(make-PRAYAG/COMMANDER, NILKAMAL).

S & F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including fixing cantilever brack-ets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm with 40mm dia CP wast coupling complete.

S & F, in repair Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanized wire staples complete all as specified and as directed.

M & L for preparation of old painted surfaces of wall n.exc 30 Sqcm in area and applying one coat of synthetic enamel paint and re-writing of bldg number by different colour complete all as specified and as directed

S & F in repair 19/20 mm thick pre laminated particle board, exterior grade pre laminated one side with decorative choice lamination & other side balancing white lamination as in kitchen cabinet or fixed with screws to timber frame work, complete all as specified and as directed.

S & F External teak wood lipping 6 mm thick for 18/19 mm thick particles board, block board or veneered particle board fixed with nails. (for Kitchen cabinets)

S & F for brass locks, cupboard, grade 1, 75mm size, 4 levers with duplicate keys with brass key hole complete all as specified and as directed.

S & F, 100mm size Hasp and staple, safety type aluminium anodized stove enameled black with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed (for Kitchen cabinet)

S & F continuous (piano) hinges, mild steel, bright finish or electrogalvanised 30mm width of flaps (for Kitchen cabinets)

S & F 40 mm dia mild steel bright finished cup board knobs fixed with nut, screw and washer complete all as spd and directed. (For Kitchen cabinets)

S & F Ball catches with 8 mm dia steel ball, and brass body and striking plate including letting in complete all as specified and as directed. (for Kitchen cabinets)

Demolition of precast concrete block masonry built in cement mortar all as specified & removal of rubbish outside MD land

M & L for brick work with fly ash bricks straight or curved on plan exc 6m mean redius built in CM 1:6

M & L for hardcore of gauge exc 63mm but n.exc100mm deposited spread and leveled in layers n.exc 15cm thick watered an rammed to a true surface with broken stone or boulders

M & L for cement concrete 1:3:6 type C2 (using 40mm graded stone agg.) as in plinth protection 75 mm thick finished top surface even and smooth with out using extra cement

M & L for applying bitumen & sand in 1:3 mix for construction joint of road etc 10mm wide & depth n.exc 75mm complete

M & L cement concrete type E-2 1:5:10 using 40mm, graded brick agg as in sub base.

M & L for polymer modified bituminous elastomanic water proof coating @ 0.60 Kg per SQM in two layers for sunken portion of toilet Make: Dr Fixit, Pidilite

M & L for integral water proofing liquid using pidi proof for LW or equivalent for sunken portion of toilets in plastering vertical surfaces & concreting at the bottom of sunken floor. Make: Dr Fixit, Pidilite.

M & L for 40mm thick PCC type B0, (1:2:4, using 12.5mm graded stone aggregate) as in floor incl water proofing liquid @ 200ml per 50Kg cement. (water proofing liquid to be measured separately) finished even and smooth.

M & L rendering 15 mm thick in cm 1:4 in sunken portion on Brick / stone masonery surfaces, incl water proofing liquid @ 200ml per 50Kg cement. ((water proofing liquid to be measured separately) including finished even and fair.

Demolition & breaking up drain pipes (SWG, AC, RCC etc) set in CM int dia of pipe 100/75mm with all fittings .

S & F PVC pipes (SWR), type 'B', single socketed in any length with rubber ring joints laid in trenches ,floor or wall for 110mm dia pipe

S & F PVC pipes (SWR), type 'B', single socketed in any length with rubber ring joints laid in trenches ,floor or wall for 75mm dia pipe

S & F PVC (SWR) junction single ( single T) equal or unequal 110mm dia with access door

S & F PVC (SWR) junction single ( single T) equal or unequal 75mm dia with access door

S & F PVC (SWR) vent cowl 110mm dia

S & F PVC (SWR) bend 110 mm dia all as specified and directed

S & F PVC (SWR) bend 75mm dia all as specified and directed

Taking down shutter exc 1.0 but nexc 2.0 SQM & removing clear off site after the credit of the same is recovered by the dept

Taking down shutter with frame of area nexc 1.50 SQM & removing clear off site after the credit of the same is recovered by the dept

Taking down shutter with frame of area exc 1.50 SQM but n.exc 4.0SQM & removing clear off site after the credit of the same is recovered by the dept

Resecuring or easing & adjusting, without taking down shutter of any description exc 1 SQM and n exc 2SQM EACH complete all as specified and as directed.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying & fixing in opening as per specification & drawing

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rails, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement, in the frame at site as per specification and shown on drawing in SSR Part-II (2004) complete all as specified and as directed.

S & F 30mm thk flush shutter solid core construction with block board core and plywood face panels commercial type on both sides

M & L, 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints etc, complete all as specified and as directed.

S & F for 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze,etc.(without sash bars), edges of framing plain,chamfered or rounded, fitted with cut and mitred beads for securing glass,etc; the size of the rail and stile as specified in SSR Part-I, Section 8, clause 8.24 (b) complete all as specified and as directed.

S & F for stainless steel wire cloth 0.36 mm nominal dia of wire, average width of aperture 1.40 mm, fixed with tinned tacks or galvanised wire staples complete all as specified and as directed

S & F for pressed steel door frames with one or more rebates incl necessary fixing lugs, hinges, lock strike plates of size 105 X 60mm

S & F aluminium anodised handles cast type 150mm long

S & F, 100mm long Stainless steel hinges, heavy duty complete all as specified and as directed.

S & F Aluminium anodized barrel tower bolt 150mm size.

S & F aluminum anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy , 300mm long, ISI marked complete all as specified and as directed by Engr-in-Charge.

S & F 250mm, ordinary rat tail, rod pattern springs including roller and roller plate complete all as specified and as directed.

S & F for aluminium powder coated partition using ‘Jindal’ aluminium SP/ DP section or equivalent make as specified with 5mm thick tinted glass, PVC rubber beading,12mm thick prelaminated particle board fixed with glazing clips etc complete all as specified and as directed. Sections : SP (Single partition) - 20033, DP (Double partition) - 20034, Glazing clips - 4407

S & F for fully glazed single/ double leaf openable door, using ‘Jindal ' aluminium powder coated sections on door floor spring, pivots, with 5 mm thick glass in panels fixed with aluminium glazing clips section No. 19381 and 19352 and PVC rubber beading all around including with 1” interlock and handle, two lever door lock, sliding wheel complete all as specified and as directed. Jindal section Nos : Top-19528, Middle – 19575, Bottom – 19530, Vertical – 19526, 1” Interlock (20939), 1” Handle (20602)

S & F in repairs framed work such as grills, grating etc. with ends of bar shouldered and/or riveted, or forged into spikes, framed guard bar confoRMing to Fe-410-W (Gde E-250) quality A complete all as specified and as directed.

M & L for 75mm thick PCC type D2 (1:4:8, using 40mm graded stone aggregate) as in sub base complete all as spd and as dirtected.

M & L for chequered cement concrete tiles 20cmx20cmx25mm thick, set , jointed and pointed in neat cement slurry as in floors with grey cement and pigment incl 15mm thick screed bedin cm 1;6 .

Dismantling MS works of any Desc not otherwise provided for (Balcony railing) & removing clear off site after the credit of the same is recovered by the dept

S & F Rolled Sections as in main croos beams , hip and jack rafters; purlins, where connected to common rafter , posts etc. conf to Fe-410-w(gdeE-250 quality-A) (for Railing at balcony)

Taking down existing treatment of any description and any layer from roof including scraping and roughening old by picking, sweeping clean and washing down to remove dust etc.complete and applying/brushing the cleaned surface with neat cement slurry 3 Kg per SQM complete.

M & L for reinforced cement concrete 1:2:4 Type B-0, (12.5 mm graded stone aggregate) , as in chajjas including form work as in repairs all as specified and directed.

M & L for rendering 10mm thick in CM 1:4 on concrete surfaces / slabs with admixture of integral water proofing compound @ 200 ml per 50 kg of cement for filling depressions if any to receive water proofing treatment (WPC shall be measured & paid seperately)

Supply only integral water proofing compound.

M & L for water proofing treatment to RCC roof slab complete all as specified below and as directed by steps of treatment are as under:- (a) Rendering 10 mm thick in cement mortar 1:4 using water proofing compound @ 3% of weight of cement on RCC roof slab , finished even and smooth without using extra cement (b) The roof surface shall be thoroughly wire brushed cleaned to eliminate all sharp projection , washed, dried up and cleaned of all foreign material and dust to receive primer (c) On the dried plastered surface, one coat of approved bituminous primer @ 0.25 Kg/SQM shall be applied. (d) on this primed surface APP modified bituminous memberance 3mm thick with non woven polyster mat as reinforcement weighing not less than 3.00 Kg/SQM with plain finish shall be laid by torch application method (d) Apply two coats of bituminous aluminium paint @ 0.15 Kg/SQM. (e) the overlap of APP shall be done with torch application end lap and side lap will be 100mm EACH(Note: (i) The contractor/Company shall furnish 10 years performance warranty as per manufacturer of material .Make : STP, Fosroc, TheRMax.

S & F 0.50mm thick corrugated pre painted / coloured galvalume sheet in roofing fixing all as per manufactures instructions with all fittings and accessories etc complete.

S & F for aluminium powder coated louvered ventilator with provision of exhaust fan using ‘Jindal” aluminium section or equivalent make as specified including glass 3mm thick ordinary quality, frosted and stainless steel wire mesh 0.36mm dia wire and 1.40mm aperture etc including taking out old frame shutter complete all as specified and directed.

S & F for aluminium powder coated three track sliding window with two glazed shutters, one 4mm thick float glass ordinary quantity and one shutter of stainless steel wire mesh 0.36 mm dia wire and 1.40mm aperture including good quality of bearing handle, locks, PVC rubber lining etc complete all as specified and as directed. Catlouge numbers of Jindal company or equivalent make as specified. Sections of Jindal company : Three track bottom – 20957, Three track top/vertical – 20958,Handle – 20606, Interlocking – 20605, Top and bottom – 20604.

M & L for scrapping and removing old paint, stains, loose materials and algae-fungus growth then cleaning of surface with water using pressure washer machine, fill the crack with acrylic based textured cack filler and applying two coats of modified acrylic exterior emulsion paint of approved shade having silicon additives in paint over a coat of primero-primer cum sealer having alkali resistance property diluted with water and mixed with bio block in ration of (5:4:1) complete all as specified and as directed. (Note: (i) The contractor shall furnish 5 years performance warranty as per manufacturer of paint (ii) The work should be done by a company recommended applicator .

M & L Rendering dubbing coat over damaged irregular surface of chajjas roof projections ceiling facia etc average 15mm thick in cm 1:4 over cement slurry coat thick @ 3 Kg/SQM making the surface even followed by 5mm thick rendering in CM 1:3 furnished even& smooth including applying two coats of weather proof emulation paint incl making of drip course as reqd complete incl roughening surface of old concrete by picking sweeping clean and washing with water all as specified. Note :Rate for foRM work if reqd to be incl in the rate quoted by the contractor.

Taking down carefully old/ damaged/unserviceable copper/ aluminium pointwiring (light, fan, socket or power) complete, (fittings such as switchs, ceiling roses, pendents, regulators sockets etc. to be measured seperately), removing materials to store for keeping insafe custody for ruse at site or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of wall, floors etc. comlete all as specified.

Taking down carefully by old/ damaged/unserviceable unscrewing from boards/outlets boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators etc complete all as specified.

Taking down carefully fan any type complete deposited in MES E/M store complete all as specified.

M & L for Sub-main wiring complete with 6 SQMm single core PVC insulated but unsheathed multistranded copper conductor cable 1100 V grade drawn through concealed PVC conduit with wall thickness not less than 1.8 mm incl sunken type pressed steel teRMinal boxes including 4 SQMm single core PVC insulated but unsheathed copper conductor grade 1100 V grade cable as earth continuity wire complete all as specified. (Make : Finolex/Anchor/Polycab)

Point wiring complete with 1.5 SQMm single core PVC insulated but unsheathed copper conductor FRLSH cable 650/ 1100 V grade drawn through concealed PVC conduit thickness not less than 1.8 mm of suitable size as per site requirement including tees, junctions etcfixed on wall/ floor/ ceiling etc including 1.5 SQMm PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire including PVC sunken type terminal box of suitable size with top cover for One Light/ Fan/6 Amps switch socket/ Bell controlled by one way switch complete all as specified Make : Finolex/Anchor/Polycab

Supply & Fixing of Ceiling fan of 1200 mm sweep 3 blade in white/ brown/ Ivory clolor with regulators, with down rod AC single phase, 230 V, 50 Hz, 5 star rating including provision of cable from ceiling rose or connector to ceiling fan complete all as specified. Make: Havells cat pat No. ES 5 or equivalent in Bajaj/ CG/ Polycab Note : Old Fan to be deposited in MES store.

Point wiring complete with 2.5 sqmm single core PVC insulated but unsheathed copper conductor FRLSH cable 650/ 1100 V grade drwn through concealed PVC conduit thickness not less than 1.8 mm of suitable size as per site requirement including tees, junctions etcfixed on wall/ floor/ ceiling etc including 1.5 SQMm PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire including PVC/ Wooden/Modular metal type terminal box of suitable size with top cover for One Light/ Fan/6 Amps switch socket controlled by one way switch complete all as specified Make : Finolex/Anchor/Polycab

Supply & fix Modular AC Motor Starter complete with accessories of capacity 32 Amps, 240 V, AC, 50 Hz all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/leather type, white/black/gold/metal finish color switch 1 way, 6 Amps, 1 modue complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/ leather type, white/black/gold/metal finish color Bell push switch 1 way, 6 Amps, 1 modue complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/ leather type, white/black/gold/metal finish color switch socket 5 pin 6 Amps, 2 modue complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/ leather type, white/black/gold/metal finish color switch socket 5 pin 6/16 Amps, combination type 2 modue complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/ leather type, white/black/gold/metal finish color Fan regulator 120 Watt 2 module complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/ leather type, white/black/gold/metal finish color cover plate frame, 2 module complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/ leather type, white/black/gold/metal finish color cover plate frame, 4 module complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/ leather type, white/black/gold/metal finish color cover plate frame, 6 module complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fix of Arteor modular mirror/graphic/wood/ leather type, white/black/gold/metal finish color cover plate frame, 8 module complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & fix of metal flush boxes mounting 2 module, made of MS chromium plated complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & fix of metal flush boxes mounting 4 module, made of MS chromium plated complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & fix of metal flush boxes mounting 6 module, made of MS chromium plated complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & fix of metal flush boxes mounting 8 module, made of MS chromium plated complete all as specified. Make : Standard Cat IVY CREST of equivalent in Legrand/ Roma/IndoAsian

Supply & Fixing of Metallic body Exhaust Fan of size 300 mm sweep, 900 RPM with louvres & shutters and all connected accessories, AC single phase, 230 V, 50 Hz including provision of cable from ceiling rose or connector to exhaust fan complete all as specified. Make : Turbo-Force Havells/Crompton/Bajaj/Polycab

S & F in repair S & Fing LED street light fitting 35/40 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including theRMal management in multiple optics complete with IP 65/66 protection complete. Make : ENDURAPEARLS35WLED757SASYTOPC of Havells or equivalent inPhilips/ Bajaj/ CG/Luker

S & F of 8 way SPN DB made of CRCA sheet, RAL 9003, powder coated for IK-09 double door, IP-43 glazed door, confiRMs to IS-8623-1, IEC 61439-1&3, 240 v with 200 amps rated bus bar , ready to use DB insulated phase busbar, neutral bar's with shroud's, earth bar, sticking saddles, cement spill protector, color coded interconnecting wire set, cable ties, blanking plates & circuit identification label with provision for DP, MCB/ Isolator/RCCB/RCBO as incomer & SP MCB's as outgoing all as specified Make: L&T cat pat No. DBSPN008GD or equivalent in Legrand/ Schneider/ ABB

S & F of 4 way TPN DB made of CRCA sheet, RAL 9003, powder coated for IK-09 double door, IP-43 glazed door, confiRMs to IS-8623-1, IEC 61439-1&3, 415 v with 200 amps rated bus bar , ready to use DB insulated phase busbar, neutral bar's with shroud's, earth bar, sticking saddles, cement spill protector, color coded interconnecting wire set, cable ties, blanking plates & circuit identification label with provision for FP, MCB/ Isolator/RCCB/RCBO as incomer & SP MCB's as outgoing all as specified Make: L&T cat pat No. DBTPE004GD or equivalent in Legrand/ Schneider/ ABB

Supply & fix of four pole RCBOS, earth leaking protection F/pi-4 sensitinity 100MA, 63 Amps complete with C/D charactrstic all as specified. Cat pat No 603412 (Legrand) Make : Legrand/siemens/schnider/L&T.

Supply & fixing in replacement of MCB TPN (3P+N), 415 Volts, 50HZ, 10KA Brecking capacity, C/D characteristics of capacity 63 Amp complete all as specified Cat pat No 006572 (Legrand) Make : Legrand/siemens/schnider/L&T.

'-ditto- but MCB SPN 32 Amp, 250 Volts (Cat pat No 604967) (Legrand) 'Make : Legrand/siemens/schnider/L&T.

'-ditto- but MCB SPN 40 Amp, 250 Volts (Cat pat No 604969) (Legrand) Make : Legrand/siemens/schnider/L&T.

Supply & fixing in replacement of MCB SP 250 Volts, AC, 50 HZ, 10 KA, C/D Charactristic of capacity 6 Amp complete all as specified Make : Legrand(Cat pat No 604951)/siemens/schnider/L&T.

-ditto- but 16 Amp (Cat pat No 604953) (Legrand) /siemens/schnider/L&T.

-ditto- but 25 Amp (Cat pat No 604955) (Legrand) /siemens/schnider/L&T.

-ditto- but 32 Amp (Cat pat No 604956) (Legrand) /siemens/schnider/L&T.

Supply, install, testing & commissioning of Storage type water geyser, electric driven (single phase), capacity 25 Litres, BEE 5 star rated vertical/ horizantal type, Rust proof body, including PTMT pipe for Cold & HOT water from ball valve to inlet & oulet of geyser respectively complete all as specified & directed by Engr-in-charge. Make :- GHWAMGTWH025 of Havells or eq in Racold

Supply & fixing in replacement of old tube light fitting with new LED tube light POLYCARBONATE FIXTURE in two optional hanging with ceiling including hanging arrangement and also incl. accessories, high power low heating superflux LEDs, 100 lumen/ watt, 120-270 V AC inbuilt electronic driver, complete all as specified for 18/20 watts LEDs. Make : LUMILINEBS20WLED865SPCWH of Havells or equivalent in HPL/Crompton/Bajaj

Supply & fixing in replacement of old tube light fitting with new LED tube light POLYCARBONATE FIXTURE in two optional hanging with ceiling including hanging arrangement and also incl. accessories, high power low heating superflux LEDs, 100 lumen/ watt, 120-270 V AC inbuilt electronic driver, complete all as specified for 9/10 watts LEDs. Make : LUMILINEBS9WLED865SPCWH of Havells or equivalent in HPL/Crompton/Bajaj

Supply & fixing in replacement of LED surface/ Recessed mounted SQUARE/ ROUND/OVAL SHAPE down luminair 12 watts Al die cast ed COB fixture in white/ Al, brush finish & complete with electronic driver suitable for MR16 application high brightness SMD LEDs P.F. > 0.90, complete all accessories, all as specified. Make : EDGEPRORDDLR12WLED840S of havells or equivalent in Crompton/Bajaj/Philips

M & L for Modular Bell, Ding Dong AC. 230 volts, single pole fitting complete. Make- Legrand/ Standard/ Indoasian

M & L 3 teRMinals Ceiling rose, AC, 230 V, PVC/ polycarbonatecomplete all as specified. Make- Anchor Penta / Cona/ C&S

M & L for Earthing complete with Galvanised steel earth plate electrode 60 cmx 60 cm x 6.3 mm thick buried bellow ground level connected to galvanised earth lead directely in ground earth pit not less than 3.20 mtr deep wire 4.0 mm dia by means of bolts , nuts, check nuts, and washer of galvanisediron or steel all as shown in electrical plate No-3 SSR Part-1 of 2009 connecting to earthing test point all as specified and directed ,including necessary excavation and earth work in any type of soil ,concre pit CI frame and cover with locking arrangement all as specified and directed by Engr . In charge. Note: Rate quoted deemed to be including excavation by compressor M/C for Soft disintegrated rock to required depth.

M & L for High density ERW PIPE of pressure rating 6 kgf/cm2 fixed/ laid in complete to walls, ceilings or in floors, trenches etc. for cable protection of outer dia 50 mm.

Supply & fixing in replacement of LEDs Decorative wall mounted dia-cast Al. LED fixture with ivory/white/Gold coating for up-down accent lighting in the module of Xing Hexa/ Penta/ Round/ Square/OVAL of capacity 14/18 Watts complete high power low heating superflux LEDs, 100 lumen/ watt, 120-270 V AC inbuilt electronic driver all as specified. Make : LUKER cat Pat No. LWL108 or equivalent in Philips/ Bajaj/HAVELLS/ Halonix/HPL

M & L for Earthing complete with Galvanised steel earth plate electrode 60 cmx 60 cm x 6.3 mm thick buried bellow ground level connected to galvanised earth lead directely in ground earth pit not less than 3.20 mtr by using GI Strip 25 X 4 mm by means of bolts , nuts, check nuts, and washer of galvanisediron or steel all as shown in electrical plate No-3 SSR Part-1 of 2009 connecting to earthing test point all as specified and directed ,including necessary excavation and earth work in any type of soil ,concre pit CI frame and cover with locking arrangement all as specified and directed by Engr . In charge. Note: Rate quoted deemed to be including excavation by compressor M/C for Soft disintegrated rock to required depth.

S & Laying in repair/ replacement cable XLPE insulated screened PVC bedded ,galvanized steel strip or wire aRMoured ,electric power cable heavy duty 1100 volts grade with strandad aluminum conducter of following sizes:- (i) 16 SQMm x 4 Core

25 sqmm x 3.5 Core

50 sq mm x 3.5 core

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth and getting out all as specified and directed in Soft / loose soil

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth and getting out all as specified and directed in hard /dense soil

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth and getting out all as specified and directed in soft rock.

Returning, filling in soil, including spreading, leveling watering and well ramming in layers not exceeding 25cm all as specified and directed.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point of any type of excavation all as specified and directed by Engineer -in-Charge.

Supply and install, testing and commissioning of FEEDER BOX Outdoor with double door, roof canopy, Angle iron pedstal frame 450 mm high above from ground level housing cucible type, panel working on 440 V 50 Hz AC supply with built in arrangement for Capacitors banks with controllers and switchgear. It shall be extendible at both ends with aluminium busbar. fully compartmentalised dust proof and veRMin proof made out of 3.15 mm thick CRCA sheet steel enclosure painted and suitable for outdoor IP-55 Protection, weather conditions as per specification & accommodate the following controls and as shown in single line diagram :- (a) MCCB 100 amps,Adjustable Thermal & Adjustable Magnetic setting 4 pole 25 KA, Ics=Icu=100% - 2 Nos (b) MCCB 32 amps, Adjustable Thermal & Adjustable Magnetic setting 4 pole 25 KA, Ics=Icu=100% - 4 Nos (h) Ammeter (0 - 100 A) - 1 No. (j) Voltmeter (0 - 500 V) - 1 No. (k) CTs 100/ 15 ma - 1 Set (l) Busbar 25X5 mm thick - 1 set. Complete wiring of panel, PCC & Installation all as specified.

M & L for road cutting and making good with PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) complete all as directed by Enger -in- charge.

S & F in repair Meter box 2mm thick MS sheet powdr coated of size1mtr x 1mtr X 0.25mtr split in two parts 0.4X 1 mtr on top for refixing the meters and .6X 1 mtr for fixing of MCCB and DB.The top portion should be provided with glass of size 10cm x 10cm infront of EACH meters to facilited recording of meter reading and including provision of wooden block of suitable size to fix the meters and DBs, door with locking arrangement and box to be fabricated such as the MCBs can be operated foRM out side including Removing and refixing of meters(4 Nos) and S & F the following:- Switch Fuse unit TPN-32 Amps 415 V-01 Nos MCB SPN 240 Volts 40 Amps including connections complete from electric meter - 04 Nos Note:rate quoted also includes fixing of the DB completely on walls with necessary cable for internal wiring in the DB,lugs insulators Etc and making good the disturdbed surface to match with the existing.

Supply & fix in replacement of Modular USB socket of 2 module complete with input 250V & output is 12/24 V DC with two USB cord arrangement complete all as specified. Make: Standard/ Legrand/ Indoasian

Samyak Engineers

H S TAKHI