Construction of Veterinary Hospital Building at Sullah Distt. Kangra (HP)

Amount

Excavation in foundation, trenches etcetera in earth work involving all classification of soil such as pick work, pick jumper work, blasting work, soft or hard rocks including chiseling/wedging out of rocks where blasting work is prohibited or any other mixed variety of intermediate soil, dewatering and removal of slush if arrisen during course of construction and lifts upto all heights including stacking the excavated soil not more than three meters clear from the edge of the excavation and then returning the stacked soil in 15 cm (fifteen centimeters) thick layers when required into plinths, sides of foundation etcetera consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth within all leads,lifts by any mode of transportation and other incidental, as per the direction and entire satisfaction of Engineer-In-Charge. Any loss to the private and public property during course of construction shall be absolute responsibility of the contractor. Rate inclusive royalty, malkana, toll tax, GST and other taxes imposed by the government.

Filling in plinth with sand under floor including watering, ramming, consolidating and dressing complete as per PWD specification. The rates are inclusive of cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of royalty, malkana, toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five millimetre) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in foundation, Footings, bases of columns and mass concrete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five millimetre) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings and the like floor etcetra. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimetre) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns, pillars , posts and struts, square, rectangular or polygonal in plain in all floor level. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five millimetre) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing in all floor. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five millimetre) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams, cantilevers, girders, lintels, sides, and soffits of beams haunchings, cantilevers, bressumers and lintels upto all depths in all floor. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimetre) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimetre) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls up to any width. The rates are inclusive of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:4:8 (One cement isto four sand isto eight aggregate) graded crushed stone aggregate 40mm (forty milimeter) nominal size mechanically mixed and curing complete, excluding cost of form work in foundation and plinth as per approved specification and drawing including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:6:12 (One cement isto six sand isto twelve aggregate) graded crushed stone aggregate 40mm (forty milimeter) nominal size mechanically mixed and curing complete, excluding cost of form work in foundation and plinth as per approved specification and drawing including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Precast concrete block masonry (including quion blocks, jamb blocks, closer etc) with solid concrete blocks of approved size made of cement concrete 1:3:6 ( One Cement isto Three Sand isto crushed stone aggregate) 40mm (Forty millimetre) in foundation, plinth and super structure in cement mortar 1:6 ( One Cement :Six Sand ) complete as per approved specification and drawing including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work M20 (M-twenty) mix design to obtain the minimum compressive strength 20N/mm2 ( twenty newton per millimeter square) with cement contents not less than 330 kg/ cum (Three hundred thirty kilogram per cubic metre) mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work in foundation footing, base of columns, and the like mass cooncrete as per approved specification, drawing and design including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of Royality, malkana, sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work M-20 design mix to obtain the minimum compresive strength 20N/mm2 (Twenty newton per millimetre square) and minimum cement content not less than 320 kg/cubic meter (Three hundred twenty kilogram per cubic metre) and curing complete and mechanically mixed and vibrated as per approved specification, drawing and design, excluding cost of form work and reinforcement for reinforced concrete work in suspended floor roofs, landing and shelves and their supports balconies, beams, girder, bressumers and cantiliver upto any floor level. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work M-20 design mix to obtain the minimum compresive strength 20N/mm2 (Twenty newton per millimetre square) and minimum cement content not less than 320 kg/cubic meter (Three hundred twenty kilogram per cubic metre) and curing complete and mechanically mixed and vibrated as per approved specification, drawing and design, excluding cost of form work and reinforcement for reinforced concrete work in column, pillers posts and struts in all depth/thickness upto any floor level. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work M-20 design mix to obtain the minimum compresive strength 20N/mm2 (Twenty newton per millimetre square) and minimum cement content not less than 320 kg/cubic meter (Three hundred twenty kilogram per cubic metre) and curing complete and mechanically mixed and vibrated as per approved specification, drawing and design, excluding cost of form work and reinforcement for reinforced concrete work in stair cases (except spiral stair cases) excluding landings, but including preparing of top surfaces and finishing of nosing upto all floor levels. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying tor steel of TISCO, SAIL reinforcement for reinforced cement concrete work including bending, binding and placing in position complete in all respects as per approved drawing, design, and specification in all floor levels including the cost of binding wire and cost of dewatering if arrisen during placement of reinforcement as per PWD specification and approved, drawing design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work M-20 design mix to obtain the minimum compresive strength 20N/mm2 (Twenty newton per millimetre square) and minimum cement content not less than 320 kg/cubic meter (Three hundred twenty kilogram per cubic metre) and curing complete and mechanically mixed and vibrated as per approved specification, drawing and design, excluding cost of form work and reinforcement for reinforced concrete work in String courses, copings, bed plates, anchor blocks, plain windows sills including preparing of top surfaces and finishing of nosing upto all floor levels. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Random rubble masonry with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement isto six sand isto Twelve graded stone aggregate) 20 mm (Twenty millimetre nominal size) at plinth level in cement mortar 1:6 (one cement isto six sand ). The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Second class brick work using common burnt clay building bricks in cement mortar 1:6 (one cement isto six sand) in super structure upto all floor lavels as per PWD specification drawing and design and curing complete including scaffolding. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Second class brick work using common burnt clay building bricks in cement mortar 1:4 (one cement isto four sand) in super structure upto all floor lavels as per PWD specification drawing and design and curing complete including scaffolding. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Second class half brick work using common burnt clay building bricks with hoop iron in cement mortar 1:4 (one cement isto four sand) in super structure up to all floor level as per PWD specification, drawing and design and curing complete including scaffolding. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Second class half brick work using common burnt clay building bricks with hoop iron in cement mortar 1:3 (one cement isto three sand) in super structure up to all floor level as per PWD specification, drawing and design and curing complete including scaffolding. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying Damp Proof Course 38mm (Thirty eight millimetre) thick with cement concrete 1:2:4 (one cement isto two sand isto four graded crushed stone aggregate 12.5mm (Twelve decimal five millimetre nominal size) mechanically mixed including cost of form work and curing complete, as per H.P.P.W.D. specification, approved drawing design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of materials within all leads lifts and other incidential. The rates is including of octroi, royality, Malkana, toll tax, sales tax or other taxes imposed by the Government.

Applying a coat of hot bitumen (mexphalt) 80/100 (Eighty by hundred) or VG-10 using 1.70 kg (one decimal seven) kilogram per square meter on damp proof course after cleaning the surface with a piece of cloth lightly socked with kerosene as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge.

Providing and fixing factory made flush door shutter 35mm thick (Thirty five millimetre thick, commercial both side i.e. non decorative, Phenol bounded, termite resistant and water proof core of black board construction with frame of first class hard wood and well matched first class Indian teak ply veneering with vertical grains of cross band and face vaneers on one face and commercial ply veneering with vertical grains of cross band on other face of shutters. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing steel glazed shutters of rolled Steel Z-section joints mitred and welded fixed to M.S. hinges in M.S Channels / angles frame using 4mm thick glass panes with M.S beeds or glazing clips of operable or fixed or partly including applying a pirming coat of red lead paint complete as per approved specificaions/ design within all leads, lifts, and other incidentals. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing steel glazed shutters of rolled Steel Z-section joints mitred and welded fixed to M.S. hinges in M.S Channels / angles frame using galvanized M.S wire gauge of I.S gauge designation 85G (Eighty five gauge) with wire of Dia 56mm (Fifty six millimetre) with M.S beeds or glazing clips of metal ash putty of approved make including applying a pirming coat of red lead paint complete as per approved specificaions/ design within all leads, lifts, and other incidentals. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Steel work welded in built up sections trusses and frame work including cutting hoisting and fixing in position and applying a primer coat of red lead paint in gratings framed guard bares ladders railings brackets and similar work etc and the like. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 0.60mm (zero decimal sixty millimetre) thick prepainted steel sheet (IS marked Z-120) of TATA durashine/ sail over steel trussed in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating of back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating Tata/ Sail/ Reliance/ Jinda including fixing with prepainted iron J or L hooks,bolts and nuts 6mm (six millimetre) diametres with prepainted limpet and rubber washers complete with all accessories as required as per the direction of Engineer-in-charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing pre-painted steel sheet ridge or hips of TATA Durashine/ Sail 60cm (sixty centimetre) over all with 0.60mm (zero decimal six zero millimetre) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheets with top coat of regulat modified polyster organic coating of 20 (twenty) microns over 5 (Five) microns primer coating + back coating of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimetre) dia prepainted bitumen washers complete in all respect as per approved drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing pre-painted sheet valleys 90cm (Ninety centimetre) over all with 0.60mm (zero decimal six zero millimetre) thick prepainted sheet of TATA Durashine/ Sail in roofing with hot dipped metalic zinc coated sheet with top coat of regulat modified polyster organic coating of 20 (twenty) mocrons over 5 (Five) microns coating + back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with J or L hooks, bolts and nuts 6mm (Six millimetre) dia with prepainted limpet and bitumen washers complete in all respect as per approved drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing M.S. B.P. sheet 2 mm (two millimetre) thick eaves board/Facia/Soffit/Ceiling including cutting, fixing and gass/electric welding steel roof member and applying a coat of red lead primer complete as per PWD specification (frame work is to be measured and paid for separately). The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Supply and fixing glass panes with putty and nails including removal of broken glass panes wherever necessary plain glass 4 mm (Four millimetre) thick complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 110mm (One hundred ten millimetre) diametres pipe on wall face C.I. rain water pipe including filling the joints with spun yarn and cement mortar 1:2 (One cement isto Two Sand), complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing on wall face PVC (D-plast) accessories for rain water pipes of Finolex/Supreme/ Prince including filling the joints with approved adhesive complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

110mm (one hundred ten millimetre) dia PVC plain bend

100mm (one hundred ten millimetre) dia PVC shoe

Providing and fixing 100mm (one hundred millimetre) dia PVC holder bat clamps of approved design rain water pipe embedded in cement concrete blocks 10x10x20cm (Ten into Ten into Twenty centimetre) of 1:2:4 (One Cement isto Two Sand isto Four graded crushed stone aggregate) 20mm (Twenty millimetre) nominal size and cost of cutting holes and making good the walls etc. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing PVC 100mm (one hundred millimetre) diametre lead caulked joined and fittings including testing of joints with approved adhesive etcetera. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing M.S. plain grills of required pattern and design in iron frames of windows/ ventilator etcetra with MS (mild steel) flats square or round bars with round headed bolts and nuts or by screws complete as per approved specification, drawing & design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing M.S. Ornamental grills of required pattern and design in iron frames of windows/ ventilator etcetra with MS (mild steel) flats square or round bars with round headed bolts and nuts or by screws complete as per approved specification, drawing & design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 19mm (Ninety millimetre) thick water proof termit resistante commercial board of Centuary/ kit ply/ Dura ply/ Action teara/(ISI marked) shelves cup board with hard wood edging and to be finished with mica laminatory of approved shades in shelves/Box complete including bright finished black enamelled iron butt hinges with screws etcetera complete as per H.P.P.W.D. specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidential. Rate inclusive toll tax, GST and any other taxes imposed by the government

Providing and fixing 19mm (Ninety millimetre) thick water proof termit resistante commercial board of Centuary/ kit ply/ Dura ply/ Action teara (ISI marked) shutter for cup board and to be finished with mica laminatory of approved shades in shutter complete including bright finished Piano butt hinges with screws including hard wood edging etcetera complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 9mm (Nine millimetre) thick water proof kit ply of standard quality ISI mark and approved shade and colour in panelling & wall linning i/c mitring at junctions, butt jointing and nails complete (Frame work for base to be measured & paid for separately). The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing moulded hand rail of M.S hollow pipe 50mm (Fifty millimetre) dia welded in straight length over M.S. flat at top of vertical balusters including one coat of red oxide priming coat complete (M.S. flat & balusters of railings shall be measured & paid separately). The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Kota stone slab flooring 20 mm (Twenty millimetre) (average) thick base of cement mortor 1:4 (One cement isto four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Kota stone slab 25 mm (Twenty five milimetre) thick in risers of steps,skirting dado and pillars laid on 12 mm (Twelve milimetre) (average) thick cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

White glazed tiles 6 mm (Six millimetre) thick in skirting risers of steps and dado 12 mm (Twelve millimetre) thick cement mortar 1:3 (One cement isto three sand) and jointed with cement slurry complete upto all floor level in all heights. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing coloured / anodized aluminum sliding door bolt, anodized transparent or dyed to required colour and shade with bolts and nuts, screws etcetra complete. . The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

300x16mm (Three hundred into sixteen millimetre) size

250x16mm (Ttwo hundred fifty into sixteen millimetre) size

Providing and fixing 300x16mm (Three hundred into sixteen millimetre) size M.S. sliding door bolt, anodized transparent or dyed to required colour and shade with bolts and nuts, screws etcetra complete. . The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing coloured anodized aluminum 150x10mm (One hundred fifty into ten millimetre) size tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetra complete . The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In- Charge.Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing coloured / anodized aluminum 125mm (One hundred twenty five millimetre) size handle anodized transparent or dyed to required shade or colour with necessary screws etcetera complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

40 (forty) millimetre thick cement concrete flooring 1:2:4 (one cement isto two sand isto three graded crushed stone aggregate) 20 mm (twenty millimetre ) nominal size laid in one layer finished with a floating coat of neat cement. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing (40 mm (Forty milimetre) wide and 4mm (four milimetre) glass strips in joints of any type of floors. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

15 (Fifteen) millimetre thick cement plaster skirting thick (up to any height (with cement mortar 1:3 (One cement isto three sand) finished with a floating coat of neat cement including rounding of junction with floor. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying marble work (Table rubbed and polished) in flooring 20 mm(Twenty millimetre) thick base in cement mortar 1:3 (one cement isto three sand ) including jointing with cement mortar 1:2 (one white cement isto Two Marble dust) with an mixture of pigment to match the shade of the marble 20 mm (Twenty millimetre) thick white makrana marble in all floors. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying red sand stone slab flooring 40mm (Forty millimetre) average thick on 20mm (Twenty millimetre) average thick base of cement mortar 1:4 (One cement isto four sand) laid over and jointed with grey ement slurry mixed with pigment to match the shade of the slab i/c rubbing and granite polish finish complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

6mm (six millimeter) cement plaster 1:3 (one cement isto three sand) in ceiling complete including curing and scaffolding complete as per PWD specification. The rates are inclusive cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15mm (fifteen millimetre) thick cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth, in rough side with cement mortar 1:6 (one cement isto six sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15mm (fifteen millimetre) thick cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth, in rough side with cement mortar 1:3 (one cement isto three sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15mm (fifteen millimetre) thick cement plaster in single coat on the fair side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth, in rough side with cement mortar 1:3 (one cement isto three sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Pointing on square rubble,coursed or un-coursed stone masonry with cement mortar 1:3(1 cement:3 Sand) Ruled pointing as per PWD specification. The rates are inclusive cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and Fixing Garsa Stone 12mm ( Twelve millimetre) cladding on R.C.C. surface side as on faces of Arch masonry walls etc. on 12mm ( Twelve millimetre) thick cement plaster 1:3 ( One Cement isto Three Sand ) and jointed with cement slurry including scaffolding etc. The rates are inclusive cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying heavy duty precast 40mm (forty millimetre) thick cement conrete inter locking paver blocks vibro compacted upto M- 50 (M-fifty) grade including border or kurb block grey or coloured over sub-base of concrete with 25mm (Twenty five millimetre) thick average thickness of cement mortar 1:4 (One cement isto four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing rubbing & polishing complete (Sub base concrete floor to be paid for saperately). The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Finishing wall with Apex weather proof exterior emulsion of Asian paint Nerolak paint/ Suraksha paint/ berger paint/Dulux paint of approved brand and manufacture and of required shade on undecorated wall surfaces (Two or more coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Applying one coat of Acrylic primer (Spectrum or equivalent of Superior quality) on new concrete/masonry/plastred surfaces after and including preparing the surface by thoroughly brushing the surface free from mortar droppings and other foreign matters, sand papering the surface smooth complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Wall painting (two coats) with acrylic emulsion paint of Asian paint / Nerolac Suraksha / Berger paint / Dulux paint approved brand approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including t horoughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Distempering (two or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings & other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer as PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Painting two coats(excluding priming costs) on new steel and other metal surfaces with enamel paint to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete With ready mixed priming paint brushing red lead, Red-oxide/zinc oxide chrome. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Painting two coats (excluding priming coat) on new steel and other metal surface under coat with ready mixed paint brusing to give an even shade including cleaning the surface all dirt,dust and other foreign matter With readymixed paint other than white. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Applying priming coat over new wood and wood based surfaces after and including preparing the surfaces by thoroughly cleaning oil, grease dirt and other foreign matter sand paparing and knotting ready mixed paint brushing wood primer pink. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Painting two coats (excluding priming costs) on new wood and wood based surfaces with enamel paint brushing to give an any shade including cleaning the surfaces of all dirt, dust and other foreign matters sand papering and stopping. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing throating or plaster drip and moulding to R.C.C. chajja complete inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing bright finished brass heaps and stapples (safety type) with necessary screws etc complete including carriage of materials. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 100mm (One hundred millimetre) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete including carriage of materials. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing orisa Pan No 20090 of size 53x41 cm ( fifty three into forty one centimeter) vitreous china water closet squatting pan (Indian Type W.C. Pan) of Cera/hindware/star white/ snow white shade with low level PVC cistern (earth work, bed concrete, foot rest and trap to be measured and paid for separately) The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 150mm ( One hundred fifty milimetre) sand cast iron P or S trap for water closet including jointing the trap with W.C. Pan in cement mortar 1:1 (One Cement isto One Sand). The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing vitreous china European type W.C. of star sr. No 20087 (S-10) of size 57x35x39 cm (fifty seven into thirty five into thirty nine centimeter) wash down water closet hindware/jaguar/cera of star white/ snow white including jet pressure integral P or S trap including jointing the trap with soil pipe in fixture ( seat cover/ jet pressure to be paid sepertely) The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing PTMT coloured/ white high density polyethylene/ poly propylene 10 ltrs.(Ten litre) capacity (full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fitting such as lead volve less syphon, 15 mm (Fifteen milimetre) nominal size P.V.C. ball valve with polythene float, with push button, couplings for connections with inlet, outlet & over flow pipes, 40mm (Forty milimetre) dia. CP flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow) pipe to be measured and paid for separately. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing vitreous China Flat back 550x400mm (Five hundred fifty into four hundred millimetre)wash basin with single hole for pillar tap with Brackets painted white including cutting holes and making good the same but excluding fittings Flat back The rate is inclusive for carriage of materials. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing vitreous China pedestal for wash basin complete recessed at the back for the reception of pipes and fittings including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing Viterous china urinal large flat back no 60002 size (39x37.50x54 cm) (thirty nine into thirty seven point five into fifty four centimetre) urinal including connecting the urinal with waste pipe by means of white lead mixed with chopped hemp ( waste pipe to be measured and Paid separtely) of star white/snow white Hindware/Cera/Jaguar within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 32mm (Thirty two millimetre) diametre C.P. brass waste (Heavy duty make ISI marked NO-8931 & 8934) Jal/ Jaguar for wash basin or sink with in all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing Stainless steel kitchen sink of size 610 x 510 mm (Six hundred ten into five hundred ten millimetre) with bowl depth 200 mm (two hundred millimetre) with drain board including carriage of materials with in all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 32mm (Thirty two milimetre) dia P.V.C. waste pipe flexible (Coil type) length not less than 800 mm including carriage of materials complete with in all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and placing water tank of make PVC (Poly venyl chloride) Sintex (Triple layer) having capacity 1000 ( One thousand) litres each with necessary fitting including over flow pipes scour pipe and bull valve and with cover locking arrangement of good quality including providing pads of sizes as required for inlet and outlet and inside painting of good quality all complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing PVC floor trap 110x90mm (one hundred ten in to Ninety millimetre) medium class, including carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing high pressure P.V.C spigot and socket soil, waste and ventilating pipe of Supreme/Finolex working pressure not less than 6.0 kg/m2 (Six kilogram per square metre) I.S.I Marked including fixing with approved adhesive etc. The rate is inclusive for carriage of material within all leads, lifts and other incidentals. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

150 mm (One hundred fifty millimetre) diametre

110 mm (One hundred millimetre) diametre

Providing and fixing PVC door bend with oval access ISI Marked of Supreme/ Finolex insertion rubber washer 3 mm (Three millimetre) thick bolt and nuts complete including fixing with approved adhesive etcetra Complete including carraige of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

150 mm ( One hundred ten millimetre) dia

110 mm ( One hundred ten millimetre) dia

Providing and fixing PVC Plain Bend ISI Marked of Supreme/Finolex/Prince including fixing with approved adhesive etcetra Complete including carraigre of material within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

150 mm ( One hundred ten millimetre) diametre

110 mm ( One hundred ten millimetre) diametre

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etcetera including carriage of materials within all leads and lifts complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

150mm (one hundred fifty millimetre) diametre.

100mm (One hundred millimetre) diametre.

Providing and fixing 100mm (One hundred milimetre) dia chromium plated grating superior quality for floor,gully, or nahani trap including carriage of materials complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 15mm (Fifteen milimetre) diameters C.P. brass bib tap of continental/ Hindware/Classic Series within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing C.P. brass pillar tap Continental/Classic sreies /florol series of Jaguare/Hindware/Cera 15mm (fifteen millimetre) dia (Heavy duty makes ISI marked No. 8931 & 8934) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing cansealed C.P. brass of Jaguar or contra (heavy duty makes ISI marked )stop cock 15mm (Fifteen millimetre) (Heavey duty makes ISI marked ) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing G.I. union within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15mm (Fifteen millimetre) nominal size diameters

20mm (Twenty millimetre) nominal size diameters

Providing and fixing C.P. brass full way valve with wheel of continental series/ clasic series/ floral series of Hindware/Jaguar/Cera within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

15mm (Fifteen millimetre) nominal size diameters

20mm (Twenty millimetre) nominal size diameters

Providing and fixing 15mm (Fifteen millimetre) nominal size diameters C.P. brass ball valve with wheel of continental series/ clasic series/ floral series of Hindware/Jaguar/Cera within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 15mm (fifteen millimetre) ferrule including boring and taping the main complete with in all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing C.P connection pipe with brass unions 45cm (Forty five centimetre) length 15mm ( fifteen millimetre) dia complete with in all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing nominal bore/ diametre to wall ceiling and floor galvanised mild steel tubes of TATA steel/jindal (Hissar) (Heavy grade) tube fittings and clamps including making good the wall, ceiling and floor. The rates are inclusive cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15mm (Fifteen millimetre) dia

20mm (twenty millimetre) dia

Providing and fixing PTMT/PVC jet sprey of continental series/clasic series/floral series of jaguar/ hindware/ cera for Europen seat of approved quality and colour with 1.5m (One decimal five metre) tube, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 600mmx450mm (six hundred millimetre into four hundred fifty millimetre) beveled edge mirror of superior glass mounted on 6mm (six millimetre) thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. screws and washers of Atul/Modi Guard/ Golden fish including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing C.P. brass towel rail size 750x20mm (Seven hundred fifty into twenty millimetre) of continental series of Jaguar/Classic of Hindware/Cera complete with C.P. brass brackets fixed to wooden plugs with C.P. brass socket including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and Fixing Toilet paper holder of continental series of Jaguar/Classic of Hindware/Cera complete with C.P. brass brackets fixed to wooden plugs with C.P. brass socket including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing chromium plated brass soap dish of ESS with C.P. brass brackets fixed with cleats with C.P. brass screws, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 100x100mm (One hundred into one hundred millimetre) size P or R type stone ware gully trap grade 'A' complete with C.I. grating, C.R. masonry in cement mortar 1:5 (One cement isto five sand) chamber and water tight C .I. cover with frame of 300mmx300mm (Three hundred millimetre into three hunded millimetre) size (inside) the weight of cover to be not less than 4.53kg (Four decimal five three kilogram) and frame to be not less than 2.78kg (Two decimal seven eight kilogram) complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Construction manhole with R.C.C. top slab in 1:2:4 (One cement: Two sand: Four graded crushed stone aggregate 20mm (Twenty millimetres nominal size), foundation concrete 1:4:8 (One cement isto Four sand isto Eight graded crushed stone aggregate 40mm (Forty millimetre nominal size) inside plastering 15mm (Fifteen millimetre) thick with cement mortar 1:3 (One Cement isto three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement isto Two sand istoFour graded crushed stone aggregate 20mm (Twenty millimetre nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred milimetre) 500mm (Five hundred milimetre) deep, including C.I. cover with frame (light duty single seal pattern–I) 450x610mm (Four hundred fifty into six hundred and ten milimetre) internal dimensions total weight of cover and frame to be not less than 38 Kgs (Thirty eight kilogram) weight of cover 23Kgs(twenty three kilograms) and weight of frame 15 Kgs (Fifteen kilograms) with 200mm (Two hundred milimetre) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement isto three sand) within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing plastic seat (Hollow type) and cover for wash down water closet with C.P brass hinges and rubber buffers Coloured plastic seat and cover within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 455x610mm (four hundred fifty five into six hundred ten millimetre) light duty rectangular C.I. manhole with frame cover weight 38KG (thirty eight kilogram) (single seat) including entire carriage of material within all leads and lifts and other incidental, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Anubhav Sharma