SPECIAL REPAIRS TO ROOF TREATMENT BUILDING NO 2/J/35, 2/J/36 AND 2/R/15 (TOTAL 24 QTRS) OF JCOs/OR MARRIED ACCOMMODATION OF 164 MH AND CERTAIN BUILDINGS AT MT YARD WITH ALLIED WORKS UNDER GE (NORTH) BINNAGURI

Amount

Taking down tarfelt with cement plaster from roof surfaces and lowering and removing the same to a distance exc. 500m and n. exc. 900m including roughening of old concrete surface of roof by wire brushing and cleaning the surface to remove all loose dust etc complete all as specified and as directed.

M&L for 10mm thick screed bed or bedding layers in cement mortar (1:4) in order to maintain proper slope over existing roof surfaces complete all as specified and as directed.

M&L for PCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in roof kerbs, water tank platforms, filling and mass concrete including necessary form work, slightly rounded or chamfered on edges, mixed with water proofing compound @ 200 ml per bag of cement or as per manufacturer instructions finished even and fair on exposed concrete surface without using extra cement complete all as specified and as directed. Note: Water proofing compound shall be measured and paid separately under relevant item of schedule 'A'.

M&L for water proofing treatment to RCC roof slab including parapet comprising of the following course of treatment / specified from bottom to top (a) Applying Bituminous primer @ 0.40 Ltr per Sqm over plastered surfaces of roof including parapet surfaces. (b) Over the priming coat laying one layer APP based polymeric membrance of approved manufacturer, 3 mm thick of weight not less than 3.60 Kgs/Sqm reinforced with non woven polyester fabric weight not less than 160 gms per Sqm. Polymeric members shall be taken to a height of 60cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrance flashing. (c) Application of two coat of bituminous aluminium paint over the polymeric membrane after necessary preparation and cleaning. Notes:- (i) Laying APP based polymeric membrance shall be done by torch on method or as per manufacturers instructions. (ii) A minimum overlap of 100mm shall be made at the end and 75mm shall be made at the sides of the polymeric membrance respectively and sealed all overlaps and joints as per Manufacturers instructions.

Disconnecting existing tanks of capacity exc 250 Ltrs and n. exc 1000 Ltrs, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in same position after cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc complete all as specified and as directed.

Dismantling water tanks and removing to store of capacity exc 500 & n.exc 1000 ltrs complete all as specified and as directed.

Supplying & fixing of PVC water storage tank 500 ltr capacity HDPE triple layered, cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection including locking arrangement, including supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 20 mm - 210 gms) complete all as specified and as directed. Note: GI inlet, outlet & wash out pipe will be measured paid for separately.

S&F in repairs 20 mm dia PVC ball cock (PVC float valves) complete high pressure with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe and fixed as required to use reducer and check nut complete all as specified and as directed.

Taking up or down GI tubing 15mm bore pipe and connection including cleaning for refixing or removal from site complete all as specified and as directed.

Taking up or down GI tubing 20mm steel tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed.

S&F 15mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors or fixed to wall etc complete all as specified and as directed.

Refixing old 15mm GI tubing and connections on new or old position (walls, ceiling, floor etc) complete all as specified and as directed. Note: The serviceable GI tubing obtained from taking down shall be reused.

S&F 20mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors or fixed to wall etc complete all as specified and as directed.

Refixing old serviceable 20mm GI tubing and connections on new or old position (walls, ceiling, floor etc) complete all as specified and as directed. Note: The serviceable GI tubing obtained from taking down shall be reused.

Supply only liquid water proofing compound conforming to relevant IS specification complete all as specified and as directed.

M&L for dismantling/demolition of RCC fins/parapets of any size including cutting down rusted reinforcement and making good with CM 1:3 and provided drip course 25 mmx10 mm deep with CM 1:3 at edges of RCC slab/chajjas etc complete all as specified and as directed.

M & L for preparing new surfaces of walls and finishing the walls with Acrylic smooth exterior paint of required shade : New work (Two or more coats) applied @1.67 Ltr/10 Sqm over and including priming coat of exterior primer applied @ 2.20 Kg/ 10 sqm). Make of Weather proof exterior acrylic emulsion and primer : Asian Apex Ultima/Berger weather coat long life 10 or equivalent as approved by the GE complete all as specified and as directed.

Demolition of brick work built in cement mortar of any description complete all as specified and as directed.

M&L for brickwork with sub class B bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 by using old size bricks retrieved from demolition complete all as specified and as directed. Note : The serviceable bricks obtained from demolition shall be reused.

M&L for brickwork with fly ash bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 by using old size bricks complete all as specified and as directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM (1:4) in two coats (10mm thick + 5mm) thick finished even and fair without using extra cement complete all as specified and as directed

S&F plain, galvanised, mild steel sheeting 63mm thickness in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and as directed.

M&L for RCC 1:2:4 type B-1 using 20mm aggregate as in fins, facias, louvers, newels, balustrade, copping parapets, and railings and the like complete all as specified and as directed

M&L for Mild steel bars 8mm dia and above cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

S&F use and waste of formwork to faces of copings, walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc. vertical or to batter complete all as specified and as directed

S&F for 25 mm thick pre-formed filler for expansion / crumple joints complete all as specified and as directed

Taking down chowkats or frame exc 1.5 Sqm but n.exe 4 Sqm each without taking off shutters from the frame including Builders Hardware complete all as specified and as directed.

Taking down frame n.exc 1.5 Sqm each without taking off shutters from the frame including Builders Hardware complete all as specified and as directed.

S&F factory made pressed steel frames confirming to relevant IS, having profile of size 105 x 60 mm, 1.25 mm thick MS Sheet for doors with one or more rebates including necessary supply & fixing lugs, lock strike plate, etc. 100 mm size hinges, with one shop coat of zinc chromate primer and fixing complete all as specified and as directed.

S&F for pressed steel frames confirming to relevant IS, having profile size 125 x 60mm, 1.25 thick MS sheet for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc. 100mm size hinges with one shop coat of zinc chromate primer and fixing complete all as specified and as directed.

S&F of factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with 19x19mm MS square tube and 1.2mm wall thickness complete all as specified and as directed.

S&F of 35mm thick 2nd class hard wood factory made, plain, framed, paneled shutter (two panel) with lock rails and panel of 9mm BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces. The size of rail and style as per IS-1003 Part-I klin seasoned and chemically pressure treated complete all as specified and as directed.

S&F for mild steel framed work such as grills, gratings, for fly proof door shutter and guard bars etc. with ends of bars, hollow sections shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, notching for wire, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting, welding etc and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F factory made 30mm flush shutter, machine pressed architects veneer designer ply lam both side flush door shutter solid core construction with block board core including 5mm thick leakwoood lipping around complete all as specified and as directed.

S&F factory made solid panel PVC door shutter, 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails MS frame shall be covered with heat moulded plain clolur PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stile and plain colour PVC sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail & bottom rail; paneling of plain color PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supplying & fixing in the frame at site as per manufactures instruction, specification complete all as specified and as directed.

S&F of stainless steel butt hinges, medium weight cold rolled of size 100mm complete all as specified and as directed.

S&F of aluminium handles cast type anodised 150mm of size complete all as specified and as directed.

S&F of 200 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

S&F in repair aluminium alloy anodised sliding door bolt 250 mm long with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and as directed.

Dismantling of steel window and ventilator of any description and size including grill/guard bar complete all as specified and as directed.

S&F factory made pressed steel windows and ventilators of standard size and section as shown on HQ CE Siliguri Zone Drg No CESZ/2018/TD-07, Sheet 1/3 to 3/3 with double shutter i.e. glazed & wire gauged shutter including all fittings like MS hold fast, box hinges, Handles , MS Tower Bolts ,Stoppers, hinges, MS stay with long screw, MS spring latch, MS Guard Bar/ grill etc complete with glazing bars including taking down of old windows and one shop coat of zinc chrome primer complete all as specified and as directed. Notes:- (a) Rate quoted shall be deemed to be including of all fittings fixtures. (b) Glass, wire mesh, MS guard bar/grill and painting only shall be measured and paid separately under relevant items of Schedule. (c) The Drawings referred above are available in the office of Engr-in-Charge and can be refereed in the office working hours if required.

S&F in steel window with side hung shutters including projecting type hinges with steel handles steel peg stay fixing lugs complete with glazing bar 10 cm dovetailed or welded including shop coat red oxide primer compete all as specified and as directed and standard size and section as shown on drawing of HQ CE Siliguri Zone Drg No. CESZ/2018/TD/07 Sheet 1/3 to 3/3.

S&F ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinges type B-21 100mm long (2 No.) suitable handle (1 No.)

Dismantling timber scantlings 40 Sqcm and over in section unframed work, in any position compete all as specified and as directed.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section compete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for compete all as specified and as directed.

S&F of rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantry, rails, plates, channels, fastening, heavy bracket framing (beam, tee, angle, channel or flat section, Tube/ square hollow MS pipes etc), including distance pieces, cleats etc. including cutting, welding & necessary fittings such as nut bolt, plate etc and framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing etc. compete all as specified and as directed.

M&L for preparation of new or previously untreated steel and Iron surface of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M&L for preparation of new primer applied steel and Iron surface of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

S&F of 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane compete all as specified and as directed.

S&F figured glass, pin head type 5 mm thick in squares n.exc 0.50 Sqm in each pane complete all as specified and as directed.

M&L for PCC type C-1, 1:3:6 using 20mm graded stone aggregate as in cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets, bed block, copings, filling concrete, gaps in between glazed & fly proof steel window, cills, railing up to 60 cm in height, in roof kerbs or mud stops, rounded or chamfered on edges, padding to roof etc including necessary form work as required compete all as specified and as directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm compete all as specified and as directed.

M&L for brick work with flyash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 etc compete all as specified and as directed.

Taking down cement plaster on wall of any description including racking out joints, hacking for key, scrubbing down with water etc compete all as specified and as directed.

M&L for applying average 15mm thick plaster in two coats (10+5mm) with ready-mix pre-packed proportioned dry mix mortar, blended with PP fibres, mixed with liquid water proofing compound on top layer on fair faces of brick wall or concrete surfaces additives on external surfaces including transporting of material, mixing, curing, scaffolding etc finished the surface even and fair without using extra cement complete all as specified and as directed. Note: Liquid water proofing compound will be measured and paid separately as supply only.

M&L for rendering 15 mm thick cement plaster on other than fair surfaces of brick work in cement mortar (1:6) finished the surface even and fair without using extra cement complete all as specified and as directed.

M&L for preparation new internal wall surfaces with one coat wall putty and applying two coats of distemper acrylic emulsion over one coat of primer with roller compete all as specified and as directed.

M&L for preparation of newly wall plastered surfaces and applying three coats of white wash on wall to match the existing colour as specified as directed.

M&L for preparation of surfaces of walls by washing, rubbing down and stopping of distempered and painted surfaces and distempering walls by applying two coats of acrylic based distemper emulsion with roller of any tint/shade with roller including wall putty / white cement wherever required to fill the wall cracks/holes complete all as specified and directed.

M&L for preparation of old treated surface of wall by brooming down or steel wire brushing; scrapping down smoke root, moulds, moss and efflorescent salts and treating oil and greasy spots and applying one coat of white wash / colour wash on old decorated surfaces of wall including washing floors, cleaning glass, joinery, electrical fittings, wiring etc of drops and splashes compete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises compete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and using 15 mm thick using cement mortar 1:6 compete all as specified and as directed.

M&L for DIGITAL ELEVATION TILES of size 300x600x7-8mm thick as approved by GE/Engr-in-Charge on vertical surfaces such as skirting, dados and riser to steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick rendering in CM 1:4 on brick wall complete all as specified and directed by Engineer-in-charge. Notes for Item No. 63 to 66:- (a) The rates include for all straight cutting and waste including raking or circular cutting and waste complete. (b) All corners in wall tiling should be properly metred/jointed to give monolithic uniform appearance. (c) Design/pattern of tile flooring shall be as approved by Engineer-in-Charge/GE at the time of execution of work. (d) The rates for tiling includes for laying to any pattern with one or more colours as directed. (e) If tiles of different sizes are used then no price adjustment shall be made.

S&F for coloured non skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile not exceeding 1 Sqm, in floors/skirting etc set and jointed in neat cement slurry over 15mm thick screed bed or bedding layer in CM (1:6) as in floor and pointed in whiter or coloured cement to match complete all as specified and as directed.

M&L for providing and laying of 600x600 mm & 20mm thick anti-skid pavement tile in approved color & Shade and in anti skid finish set and jointed in neat cement slurry and pointed in white cement & pigment to match over and including 20 mm thick screed bed in cement mortar 1:4 compete all as specified and as directed.

Demolition of cement concrete (un-reinforced ) in ground floors and pavings n.exc 15 cm thickness (below or above ground level) compete all as specified and as directed.

M & L for PCC 25mm thick type B-1, 1:2:4 (using 20 mm graded stone aggregate) as in sub base of floor compete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) Type C-2 (40 mm graded stone aggregate) as in plinth protection including finishing the concrete surface even and smooth w/o using extra cement compete all as specified and as directed. Note: The unit rate quoted shall be deemed to include for providing the concrete in alternate bays n exc 3 mtr long with 12 mm wide and 50 mm deep joint between the bays which shall be filled with mastic filling with hot bitumen 85/25 and 1:2 mix by volume.

M&L for 75 mm thick cement concrete type C2 1:3:6 with 40 mm graded stone aggregate as in sub base to receive a surface compete all as specified and as directed.

M&L for cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) 50mm thick as in sloping ramp, floor etc including finishing the concrete surface spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified including demolition or hacking as necessary compete all as specified and as directed. Note: The unit rate quoted shall be deemed to include for providing the concrete in alternate bays n exc 3 mtr long with 12 mm wide and 30 mm deep joint between the bays which shall be filled with mastic filling with hot bitumen 85/25 and 1:2 mix by volume.

M&L for PCC 1:3:6 type C2 (with using 40mm graded aggregate) as in saucer drain, storm water drain, bed of drain etc like water through including forming channels complete all as specified and as directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth in brick walls compete all as specified and as directed.

S&F in repairs 15 mm dia Bib taps, CP cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed compete all as specified and as directed.

S & F in repair 15mm dia concealed stop cock/angle cock CP, cast copper alloy fancy type with long shank and cup for 15mm pipe compete all as specified and as directed.

S&F PVC (SWR) multi floor trap 75mm/100mm, plain with grating including jointing with solvent cement compete all as specified and as directed.

S & F ceramic undercounter wash hand basin Glossy finishes, size 22x16x8 inch including CP waste coupling, PVC connection 450 mm long, waste pipe and removing the existing Basin, cutting for and pinning ends of brackets or erecting stand compete all as specified and as directed.

S&F in repairs 15 mm bore pillar taps, capstan head, cast Copper alloy, chromium plated, screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F stainless steel towel ring and including Chromium plated brass screws and wooden / plastic cleats compete all as specified and as directed.

S & F of polycarbonate wall mounted soap dish fixed to plugs with chromium plated brass screws compete all as specified and as directed.

S&F 1000 ltrs capacity rotaional moulded polyethylene water storage in triple layer (cylindrical vertical with closed top) hoisted and fixed in positions all specified in SSR Part I compete all as specified and as directed.

S&F in repairs of brass Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union compete all as specified and as directed.

S&F vitreous china squatting pan "Orissa" pattern size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) with 'P' or 'S" trap front or back inlet etc including connection to trap and flushing pipe and provision of cement concrete bedding complete all as specified and as directed in repairs including demolition of existing one.

S&F in repair 10 ltr capacity PVC flushing cistern low level white colour including PVC connection 450 mm long, PVC flush pipe of required length etc complete all as specified and as directed.

S&F in repair vitreous china half stall type urinal with grating and union for discharge pipe including connecting pipe & waste pipe with coupling, Urinal Spreader compete all as specified and as directed.

S&F in repair 15 mm dia brass chromium plated angle cock with flange compete all as specified and as directed.

S&F CP Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections, fixing in pipe etc. and fixed in position complete in all respect compete all as specified and as directed.

S&F in repair 110mm dia PVC SWR pipes single socketed in any length with rubber ring joints, fixed to wall compete all as specified and as directed.

S&F in repair 110mm dia PVC SWR bends of any radius with out access door complete all as specified and as directed

S&F in repair 110mm dia PVC (SWR) junction single 'T' equal or unequal with access door compete all as specified and as directed.

S&F in repair 110mm dia PVC (SWR) branch piece, single ‘Y‘ equal or unequal compete all as specified and as directed.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Use and waste formwork to fins, louvers, fascia. etc Fair finished surfaces of concrete flat compete all as specified and as directed.

Dismantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings compete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings compete all as specified and as directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws including all necessary accessories compete all as specified and as directed.

S&F for Pre-painted galvalume aluminum zinc coating GI based Plain or curved crimped steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including all necessary accessories compete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets compete all as specified and as directed.

S&F for GI frame work for seamless ceiling comprising of FI perimeter channel 0.55 mm thick with two unequal flange of 20 and 30 mm dia and Web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended form soffit at approx 900 mm centre to centre with FI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 mm length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre compete all as specified and as directed.

M&L for 4mm thick non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws compete all as specified and as directed.

ELECTRIFICATION Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

Taking down the existing unserviceable main switch/ cut out/ DBs of any type/ capacity/ description as existing at site including making good the disturbed surfaces to match with the existing finishes all as specified.

M&L for point wiring complete with 1.5 Sqmm single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with multistranded copper conductor with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheated copper conductor cable FR-LS (ISI markd) with proper colour coding as earth continuity conductor connected to common earth dolly , modular sheet steel sunken terminal box of appropriate size suitable for modular switch/ fittings concealed in walls, with modular back plate, top cover fixed flush to wall for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles compete all as specified and as directed for the following :- One light point controlled by one way switch 5/6 amps compete all as specified and as directed.

One ceiling fan/Exhaust fan point controlled by one way switch 5/6 amps compete all as specified and as directed.

One socket out let 5/6 amps point on the same board compete all as specified and as directed.

One socket out let 5/6 amps point on the independent board compete all as specified and as directed.

All as per item No 104 above but wiring with 2.5 Sqmm single core multistranded copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified and directed

S&F switch piano single pole flush type 5 amps, 230 volts one way complete all as specified and as directed.

S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified and as directed.

S&F ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and as directed.

S & F lamp holder, insulated body, with back plate suitable for batten/angle fittings complete all as specified and as directed.

S&F LED white glass Lamp 1x9 Watt 230V Base-22 complete all as specified and as directed.

S&F of Modular switch, single pole, one way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of Modular switch, single pole, one way, 16 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of Modular shuttered Socket outlet 5 Pin, 6 Amp, 2 Module, 230 volts, ISI marked complete all as specified and as directed.

S&F of Modular shuttered Socket outlet 6 Pin, 6/16 Amp, 2 Module, 230 volts, (ISI marked) complete all as specified and as directed.

S&F of stepped type modular electronic fan regulator 120 watt 2 module suitable for 1200/1400 mm sweep energy saving fans, ISI marked complete all as specified and directed.

S&F IP 20, class I, LED light 1X18 W (or nearest next higher wattage) (4feet), 5700K, wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting compete all as specified and as directed.

S & F Energy saving new generation environmental friendly long life versatile pressure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 35 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtr long bend to required shape complete including removal of old unsv fitting compete all as specified and as directed.

S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, single pole & neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB"S/isolators complete with and including taking down old unsv one all as specified and directed including taking down the existing unserviceable main switch/ cut out/ DBs of any type/ capacity/ description as existing at site including making good the disturbed surfaces to match with the existing finishes compete all as specified and as directed.

S & F MCB TPN 415 volts suitable for fixing in MCB DB of capacity 40 / 60 amps compete all as specified and as directed.

S & F MCB SPN 230 volts suitable for fixing on MCB DB of capacity 6 to 30 Amps compete all as specified and as directed.

S&F MCB, Single pole, 5 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete with and including taking down old unsv one compete all as specified and as directed.

M&L for SPN enclosure with two pin and earth plug and socket with 240 volts 20 Amp SPN MCB including removal old unsv one compete all as specified and as directed.

Material and labour for earthing complete with galvanized steel plate electrodes of size600x600x6mm thick buried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised iron strip25 x 4 mm earth lead by means of nuts, bolts, check nuts and washers including 15 mm bore galvanized iron pipe, medium grade for protection of earth lead upto the length of 7.5 meter towards test terminal and 20 mm bore galvanized iron pipe, medium grade for watering, and providing of charcoal and common salt in alternate layers, including necessary earth work in any type of soil and including PCC pit in PCC 1:2:4 with provision of wire mesh and funnel, complete all as shown in electrical plate No 3 of SSR Part- I including testing compete all as specified and as directed.

Taking down carefully Ceiling fan from its original position and refixing / hanging after B/R plaster work compete all as specified and as directed.

M&L painting of ceiling fan complete, in situ with synthetic enamel paint by spraying including filling cavities with filler one coat after cleaning all dust etc compete all as specified and as directed.

Taking out old unserviceable cable of any size carefully from trenches after disconnecting electric connection, GI pipe protection, with and including separating serviceable bricks & set aside and removing un-serviceable bricks from site complete all as specified and as directed. Note: The Excavation and earth work shall be measured and paid separately under relevant item of Schedule.

Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulated PVC bedded, galvanized steel strip or wire armoured LT electric power UG cables, heavy duty with stranded aluminium conductor of cross sectional area 16 sqmm 4.0 core with and including all fixing & connecting accessories such as Alluminium cable lugs, cable gland, nut, bolts, washer etc complete as specified and as directed. Note: Earthwork & Excavation, GI pipe, bricks for protection etc shall be measured and paid separately under relevant items of this Schedule 'A'.

Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulated PVC bedded, galvanized steel strip or wire armoured LT electric power UG cables, heavy duty with stranded aluminium conductor of cross sectional area 10 sqmm 2.0 core with and including all fixing & connecting accessories such as Alluminium cable lugs, cable gland, nut, bolts, washer etc complete as specified and as directed. Note: Earthwork & Excavation, GI pipe, bricks for protection etc shall be measured and paid separately under relevant items of this Schedule 'A'.

Excavation in trenches in soft/loose soil not exc. 1.5 metre wide and not exc. 1.5 metre in depth and getting out for taking up / laying under ground electric cable complete all as specified and as directed.

Returning, filling in, including spreading leveling watering and well rammming in layers not exceeding 25 cms in depth complete all as specified and as directed.

Removing surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and as directed.

Supply and lay dry river sand filling for under ground cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and as directed.

Supply and laying sub class B bricks of old size for protection of UG cable with width equal to length of bricks as mechanical protection laid dry and flat complete all as specified and as directed.

Horizontal boring of holes, under road/ pavement / hard standing etc. not exceeding 10 Metres in length, in any type of soil, suitable for passing through up to 50 mm bore, galvanised steel tubing complete all as specified and directed.

Supplying and fixing Galvanised mild steel pipe /tubing, light grade complete with all fittings of 32 mm bore dia, laid in trenches / under roads, fixed to poles/ walls with Mild steel clamps, bolts, nuts and washers as in cable protection complete all as specified and directed. Note: Excavation & Earth work shall be measured and paid separately.

Taking out old unserviceable GI Pipe of any size from site complete all as specified and as directed. Note: The Excavation and earth work shall be measured and paid separately under relevant item of Schedule.

Supply and lay pipe galvanized, “Medium grade”, including fittings 25 mm dia fixed complete to walls and ceiling or laid in floor complete all as specified and as directed.

Supply and fix Gun metal, globe Gate Valves with iron wheel head of 25 mm dia bore complete with all accessories complete all as specified and as directed.

Supply and fix Gun metal, globe Gate Valves with iron wheel head of 20 mm dia bore complete with all accessories complete all as specified and as directed.

M& L for cutting existing GI pipe alteration or addition of upto 40 to 50 mm dia bore for insertion of reducer Tee complete with all accessories complete all as specified and as directed.

L. B. SHARMA

SS SHARMA

M/S S.K. CONSTRUCTION

S K GUHA

MESSRS SEN BROTHERS

M/s. RAMPHAL GARG

flexpro construction company