CA NO.CWE BLY/GE (E)/12 OF 2025- 2026SPECIAL REPAIR TO BLDG NO P-136 SINGLE LIVING ACCN OF 306 FD HOSP AND BLDG NO P-112 ADM BLOCK OF 406 FD HOSP UNDER GE (EAST) BAREILLY

Amount

Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors ,aprons laid,bedded and jointed in any mortar etc complete all as specified and directed.

Demolition of unreinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness below or above ground level complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

Demolition of cement concrete unreinforced of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Excavating in trenches n. exc. 1.5 m wide, and n.exc. 1.5 m in depth for foundation etc. n.exc. 10 sqm on plan and n. exc. 1.5 mtr in depth and getting out soft/ loose soil complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) and removing to store complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) and removing to store complete all as specified and directed .

Dismantling of 100 mm bore cast iron/ PVC drain pipe or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store complete all as specified and directed.

Taking up or down 15 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed.

Taking up or down 20 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed .

Dismantling water tanks exc 500 but not exc 1000 Litres, and removing to store complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 to brick masonry wall surfaces or on other than fair faces of brick wall surfaces for fixing tiles etc complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate as in floors to receive surface of tiles complete all as specified and directed.

M&L for screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes/ tiles complete all as specified and directed.

M&L for screed bed or bedding layer of mortar, 20 mm thick, in cement mortar 1:6, for laying floor finishes/ tiles complete all as specified and directed.

M&L for Non- skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L for virified glazed ceramic coloured/ double charged/ ultra charged tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in matching colour 5 mm thick epoxy filling in between tiling complete all as specified and directed.

M&L for virified glazed ceramic coloured/ double charged/ ultra charged tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in vertical surfaces etc. set and jointed in neat cement slurry and pointed in matching colour 5 mm thick epoxy filling in between tiling complete all as specified and directed.

M&L for virified ceramic exterior heavy duty out door coloured tiles 12 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, on floor set and jointed in neat cement slurry and pointed in matching colour 5 mm thick epoxy filling in between tiling complete all as specified and directed.

M&L for virified glazed ceramic coloured/ double charged/ ultra charged tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding .42 sqm, in floor etc. set and jointed in neat cement slurry and pointed in matching colour 5 mm thick epoxy filling in between tiling complete all as specified and directed.

M&L for virified ceramic dark shade/ double charged/ ultra charged tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M&L for 7 to 8 mm thick glazed coloured ceramic tiles (square/ rectangular) with border, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in vertical surfaces such as skirting or dado set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25 mm thick over 20 mm thick screed bed laid in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing and treating the surface complete all as specified and directed.

M&L for green marble of work 18-20mm thick (table rubbed and polished) in treads and riser and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including moulding and nosing complete all as specified and directed.

M&L for 18-20 mm thick Granite of black colour (table rubbed and polished) in window cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with full round bull nosing edging complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 , type C-2 using 40 mm graded stone aggregate as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed.

M&L for 100 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base floor/pavings complete all as specified and directed.

M&L for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness ,M-35 grade complete all as specified and directed.

M&L for cement concrete coloured inerlocking paver blocks shall be factory made with casting in rubber/ PVC moulds & compacting on a vibro table assembly and shall be cured in curing tank for atlest 14 Days and then air dried before use. The paver block shall be confirmng to IS 15658-2066 of 60 mm thickness, M-35 grade. Approved design, shape, size and colur of top layer complete all as specified and directed.

M&L and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line,level and curvature, jointed with cement mortar 1:3 (1 cement:3 coarse sand) ,including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm) including making drainage opening wherever required complete all as specified and directed.

M&L for reinforced cement concrete 1:1.5:3 type A-1 (using 20 mm graded stone aggregate) (nominal mix) as in slabs supported on wall ,landing, balconies, shelves and like including bonding agent complete all as specified and directed.

M&L for form work to chajja, slab ,weather shade, troughs and similar items including edges for rough finished surfaces of concrete flat complete all as specified and directed.

M&L for form work to edges of concrete flats, treads, breaks in floors window cill, concrete railing opening in conc wall , floor and roof n.exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

M&L for TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) but not less than 0.9 mm dia conforming to Fe-410 - 0 complete all as specified and directed.

M&L for brick work with fly ash old size bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:6 on brick masonry surfaces or on other than fair faces of brick masonry finished even and smooth witout using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar 1:4 to brick masonry wall surfaces or on other than fair faces of brick masonary finished even and smooth without using extra cement with using water proofing liquid @ 0.15 Ltr per bag of cement complete all as specified and directed. Note:- Water proofing liquid shall be measured and paid seprately.

M&L rendering 5 mm thick in CM 1:4 as on concrete surface on ceilings finished even and smooth without using extra cement complete all as specified and directed.

M&L for applying cement slurry over existing roof surface @ 3 Kg/ Sqm including mix with water proofing liquid @ 0.15 ltr per 50 Kg cement complete all as specified and directed.

M&L for PCC 1:2:4 type B-0, using 12.50 mm graded stone aggregate as laid over roof slab after applying cemet slurry for filling undulations finished evn and smooth without using extra cement complete all as specified and directed.

M&L for screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4 over RCC roof slabs for laying water proofing treatment mixed with using water proofing liquid @ 0.15 ltr per 50 Kg cement complete all as specified and directed. Note :- WPC shall be measured and paid separately.

supply Integral water proofing Liquid complete all as specified and directed.

S&F pressed steel frames 125x60 mm, 1.25 mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

S&F 30 mm Plain, framed, panelled shutters (any number of panels), 2nd class HW, with panels of timber flat on both sides (feather edged),or of veenered particle board medium density ,wood particle board with comercial face veeners complete all as specified and directed.

S&F 30mm thick factory made glazed and skeleton door shutters open rebated, of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain cham-fered or rounded, mitred and rebated sash bars, any numbers The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S&F 150 mm long Floor door stopper of aluminium alloy body and tongue with hard drawn steel spring fixed in floor complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick single side prelam PVC sheet used instead of Plain colour PVC sheet , suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F 30 mm thick factory made both side Prelam PVC sheet used instead of Plain colour PVC sheet. Stile and rails feathered at edges consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F for aluminium powder coated frame hollow sections members of size 63.50 mm x 38mmx 1.48 mm thick, 3 mm thick aluminium composite panel into the wall for kitchen cabinet/ cupboard shelf with aluminium clip/strips/beading with rubber gasket , design as pe site requirement basis, complete all neccessary fitting complete all as specified and directed.

S&F aluminium alloy powder coated aluminium door frame fixed with side hung shutters and glazing fixed with and including 5.50mm thick tinted glass fixed with rubber gasket with aluminium heading, clips frame made with aluminium box sec as appended below complete all as specified and directed (a) Frame 100x44x1.20mm thick with rawl plug (b) Middle/style rail : 85x44x1.20mm thick (c) Bottom/top rail : 114x44x1.20mm thick (d) Aluminium beading : 0.7mm thick (e) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long brass mortise lock 100mm 4 leaver aluminium stopper, cleat double action floor spring hydraulically regulated made of n.less than 1.25mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other part of steel heavy duty ( Make Sandhu marked or its equivalent approved make) (f) 300 mm long aluminium sliding door bolts plate type with bright bolt not less than 16 mm dia including all fitting (g) Making good of wall surface to match with existing surface complete.

S&F aluminium alloy powder coated aluminium door frame fixed with side hung shutters and glazing fixed with and including 5 mm thick aluminium composite panel LDPE core PET coating (both side decorative type) fixed with rubber gasket with aluminium heading, clips frame made with aluminium box section complete all as specified and directed as appended below:- (a) Frame 100x44x1.48mm thick with rawl plug (b) Middle and lock rail : 150x44x1.48mm thick (c) Bottom rail : 150x44x1.48mm thick (d) Top rail/style : 85x44x1.48mm thick (e) Aluminium beading : 0.7mm thick (f) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long brass mortise lock 100mm 4 leaver , with S S hinges complete (g) Making good of wall surface to match with existing surface complete.

S&F 12 mm thick toughned glass door with powder coated aluminium frame including neccessary locking ,handle etc with double action floor spring in each shutter complete as requirement of site with suitable height and any type of eaching designed on tougned glass, off cuts complete with finishing wall in CM 1:4 complete all as specified and directed.

Providing & fixing false ceiling at all heights with GRG (Glass Fiber Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanized iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws complete all as specified and directed.

S&F Powder coated aluminium sliding windows frame with movable shutter ( sliding on minimum two PVC roller of best quality, for each shutter on three tracks with stainless steel mosquito proofing and glazing shutter and incl 5.50 mm thick glass & stainless steel wire messs fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium specified and directed as appended below:- (i) Window frame :95x38mm X 1.15 mm thick for three tracks. (ii) Top/bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over. (iv) stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperature 1.40mm and fixed in aluminium window or alongwith F/Y section fixed with aluminium wire staples complete. (v) Aluminium fittings such aluminium suitable handle with auto interlock cap with suitable size . (vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed.

S&F Powder coated aluminium sliding windows/cupboard shutter and frame with movable shutter (sliding on minimum two PVC roller of best quality on two tracks with stainless steel mosquito proofing and glazing shutter and incl 5.50 mm thick glass & stainless steel wire messs fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below:- (i) Window frame : 63x35mm X 1.48 mm thick for two tracks. (ii) Top/bottom rail and style / rail of shutter : 19x38x1.48mm thick and over. (iii) Aluminium beading - 0.7mm thick (iv) Aluminium fittings such as aluminium suitable fittings for auto interlocking closing (v) Making good of wall surfaces to match with existing surfaces complete all as specified and directed.

M&L for powder coated aluminum window/ doors grills fixing along with frame of following specification, grills with opening 69.4mm x 78.2mm grills thickness shall be of 6.4mm x 5.8mm having weight not less than 2.306 Kg/per sqm shape as ordered with frame channel of 34 x 11mm x 1.7mm thick fixed with screw inside of the window complete all as specified and as directed.

S&F roller / venetian blinds vertical / horizontal type made out of standard cloth of approved texture with necessary accessories etc complete all as specified and directed.

S&F Powder coated aluminium ventilators box type with louvers & wire mesh fixed with neoprene rubber gasket, aluminium beading, clips. Frame made with powder coated aluminium section of size as appended below (i) frame :45.2mm x35mm X 1.15 mm (ii) Aluminium beading - 0.7mm thick (iii) Glass louvers depth 6 inch. Blade Angle: 38 degrees and thickness of blade 2.02 mm with 106.25 mm spacing. (iv) Aluminium neccessary fittings complete as required. (v) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed.

S&F in repair PVC hollow interlocking wall paneling of 5mm thick prelam PVC sheet. The panel & strips shall be of 600 kg / cum density manufactured by an ISO-9000 certified company. The strips should two PVC strips. The PVC strip shall be fixed to the wall using 65mm long M.S screws through the groove in the strip by using PVC fasteners. The distance between two screws shall not be more than 200mm. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a strips of 5mm thick PVC sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are joined, using solvent cement complete all as specified and directed.

S&F in repair vitreous chinaware coloured wash hand basin with pedestal of size 55X45X82cm complete including fancy CP pillar tap, CP Waste coupling, waste pipe, complete fixing arrangement and cutting for and pinning in walls & making good complete all as specified and directed.

S&F in vitreous china table top wash basin of suitable size including SS bottle trap, HDPE waste pipe including fixing on counter with SS waste coupling complete all as specified and directed. Model : Cat No 91072 Orchid of Hindware , Parryware Cat No C0483, Cera Cat No FLS-WHT-0575

S&F in repair vitreous China bowl urinal flat back size 465x355x265 mm with grating and union for discharge pipe excluding flushing cistern flush pipe and waste pipe complete all as specified and directed.

S&F in repair wall mounted censor urinal size 370x315x620 mm with all fixing Accessories complete all as specified and directed.

S&F in repair stainless steel of AE - SI 316 grade tubular towel ring including a pair of CP brass bracket complete all as specified and directed.

S&F in repair rimless single piece wc with UF soft closed sheet cover, hinges, fixing, accesories, accesseries sets and cistern fittings size 360x675x750 mm, S trap 300 mm including making good to floor complete all as specified and directed.

S&F PTMT alloy toilet cabinet with mirror of overall size 350 x 450mm and fixed to wall complete all as specified and directed.

S&F in repair stainless Steel plate rack of size 90x80x25cm made with 1.00 mm thick sheet including taking out existing wooden plat rack, complete all as specified.

S&F in repair 0.8 mm thick stainless steel kitchen sink size 590x460x230mm undermount, single bowl (bowl size 540x410x230 mm) , including waste pipe & SS coupling, washers etc. complete all necessary fittings complete all as specified and directed.

S&F mild steel framed work as in window grill, box type, guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding complete FE-290 grade E-165 complete all as specified and directed.

S&F Steel windows with pressed steel frame (size 95x45x1.25 mm) side hung shutter including box type hinges with steel handle ,and steel peg steel complete with glazed openable shutter with glazing bar (open out side) and wire gauzed openable shutter without glazed bar (open in side) dovetailed or welded complete all as spd and directed and all as per drg no TD/088 dt 07 Jun 2002 Note:-(i) Two shutter ie wire gauged and glazed shall be fixed in one composite frame and both shutter shall be measured as one unit (ii) Rate for filling of PCC in frame deemed to be included in quoted rate (iii) MS grill shall be measured and paid seprately under relevant item of schedule

S&F steel ventilator fixed type ,with glazing bars complete welded including one shop coat of Red oxide Zinc chromate primer complete all as specified and directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc. 0.5 Sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth, 0.56 mm nominal dia of wire and average with of aperture 1.18 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 300 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150 mm thick Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150mm size aluminium handles, cast type anodised complete all as specified and directed.

S&F 100 mm size butt hinges medium weight colled rolled mild steel complete all as specified and directed.

S&F in repair 300mm size ordinary mild steel , rat tailed rod pattern spring including roller and roller plate welded to mild steel frame complete all as specified and directed.

S&F 300 mm long aluminium sliding door bolts plate type with bright bolt not less than 16 mm dia with and including a minimum of 6 bolts and nuts, 04 Nos on bolt plate and 02 Nos on staple plate and fix complete all as specified and directed.

S&F 1000 litres, rotational moulded polyethylene water storage tank (Cylindrical vertical with closed top), hoisted and fixed in position complete all as specified and directed.

S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F 15 mm dia steel water tubing galvanized medium grade concealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed.

S&F 20 mm dia steel water tubing, galvanized, medium grade concealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed.

S&F in repair brass chromium plated wall mixer 3 in 1, 15mm for mixing hot & cold water screwd down three joints to steel pipes or unions and plugging and screwed to walls complete all as specified and directed.

S&F in repair fancy type 150mm size square brass CP shower rose complete all as specified and directed.

S&F in repair 15 mm bore dia bib tap fancy type chromium plated with flange quarter turn complete all as specified and directed.

S&F in repair 15mm bore dia of pipe fancy type chromium plated brass two way bib cock complete all as specified and directed.

S&F stainless steel of grade tubular towel ring including a pair of CP brass bracket complete all as specified and directed.

S&F in repair 15mm bore PVC connections, with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair fancy type brass chromium plated soap dish of 160x160x90 mm complete all as specified and directed.

S&F in repair 15mm bore dia of pipe fancy type chromium plated brass angle valve type complete all as specified and directed.

S&F in repair fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP brackrt gaurd and railling 60 cm long complete all as specified and directed.

S&F 20mm bore dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair 15 mm dia fancy type stop cock, chromium plated with long shank and cup (conncelaed type) for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair vitreous china squatting pan of orissa pattern long pan size 580 x 440 mm white with "P"or "S" trap size 100 mm dia front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding complete all as specified and directed.

S&F in repair vitreous China coloured European type WC with "P" or "S" trap 75 mm dia white, including connection to drain or out going pipe and flush pipe anti symphonize pipes etc complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 litres, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, flushing pipe complete all as specified and directed.

S&F Vitreous China counter top oval type coloured wash basin 500x380x120 mm size including swan neck pillar taps with bottle trap but including waste pipe fixing on counter with stainless steel brackets complete all as specified and directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repair PVC (SWR) multi floor trap with grating including jointing with solvent cement floor trap 75 mm dia outlet plain with grating including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed.

S&F PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) 110 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

M&L for reinforced concrete pipes 150 mm dia,class NP2 ,laid and jointed complete with collars complete all as specified and directed.

S&F in repair 20 mm dia stainless steel 1.0 mm thick fancy type droppery rod with decorative design matching brackets as approved and knobs (lattu) or end bracket as required incl fitting with 80 mm long SS screw with 75 mm long wooden gitty of appropriate c/s in each end & intermediate support complete all as specified and directed.

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming Fe-410-W(Gde E-250)quality-A complete all as specified and directed.

S&F pre-coated galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, Chajja ( up to IInd floor) etc making good, cutting exc 10cm and not exc 20cm girth in brick walls complete all as specified and directed.

Dismantling of concrete by chiseling from RCC members like column , beam, parapet facia, chajja, ceiling,etc exposingthe reinforcement without disturbing the reinforcement free from rust by sand blasting/using chemical , apply a coat of rustolin to remove rust and acralic polymer on old rusted reinforcement proving at places addl reinforcement welding with existing reinforcement as directed wherever required binding RCC 50 mmx50 mm (10 mm gauge welded mesh ) & tack , securing with clips / blinding wire, welding & provision guniting pressure 2.2 to 2.5 kg /sqm with admixer 1 cement 3.5 of sand of thickness 25 to 40 mm including stripping floating with wooden strippers for proper dimension control neccssary form work & scaffolding up to three storey and including height of head room complete surface of guniting to be finished fair with 10 mm thick plaster in cement mortar 1:4 with water proofing compound @3% by weight of cement and construction fibre as per manufacturer instruction cleaning & removing of waste meterial etc as dirply two coat of Water proofing liquid at interval of 8 hours cure for the surfaces complete all as specified and directed.

S&F 0.71mm thick Aluminium plain sheeting Alloy 31000 H4, stucco embossed finish with fixed with coach screw and Aluminium washer in roof and wall etc. with end laps stitched with 25x6mm G.I. bolts at 20cm apart gap to be with thermocol sheet including dismantling complete all as specified and directed.

M&L for preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed.

M&L for complete removal of existing treatment on wall by scrapping with mechanical sander (having mechanical vaccum mechanism ) with sanding pad of appropriate grit to make surface clean ,free from dust ,loose paint etc by skilled labour and applying two coat OBD on wall with airless electric sprayers over a coat of primer applied using airless electric sprayer over two coat of wall care putty of 1mm thickness complete all as specified and directed. Note:-Application to be done through authorised dealer.

M&L for applying of two coats OBD on newly plastered surface of wall with airless electric sprayers over a coat of primer applied using airless electric sprayers over one coat of wall care putty of 1 mm thickness prepared and sanded with electrically operated sanding machine complete all as specified and directed. Note:- Application to be done through authorized applicator

M&L for preparation of newly plastered surface of walls and applying two coats of Dust Resistant and Anti Algal weather proof exterioremulsion paints over a one coat of wall care putty complete all as specified and directed.

M&L for preparation of old/ newly plastered surface of walls cleaning the surface throughly by using wire brushes and removing loose materials from the surface and applying two coats of Dust Resistant and Anti Algal weather proof exterior/ internal emulsion paints complete all as specified and directed.

M&L for complete removal of existing treatment on surfaces of walls including cleaning the surface throughly by using wire brushes and removing use materials from the surface and applying two coats of Dust Resistant and Anti Algal weather proof exterior emulsion paints over a one coat of wall care putty complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed.

M&L for complete removal of existing treatment on ceiling,etc including cleaning of any mortar drops ,fungus efflorescent salts etc and prepration of old plastered surface and applying two coat of white wash complete all as specified and directed.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings, tube light fittings etc complete and also making good disturbed surfaces of wall, floors etc complete all as specified and directed.

M&L for point wiring complete for one light/ fan/ bell point controlled by one way switch with single core FRLS PVC insulated, unsheathed, multi stranded copper conductor cables 1.5 Sqmm 1100 volts grade, and PVC conduit of size 20 mm dia and above medium grade including all fitting concealed in wall/ ceiling including cutting and chasing or passing through the existing conduit as per site requirement where cutting and chasing of wall and ceiling not feasible and as directed with and including FRLS including FRLS PVC insulated unsheathed 1.5 sqmm copper earth wire, connecting to common earth dolly in metal flush box of suitable size for fixing modular swtiches/ sockets and making good surface by wall panelling etc complete all as specified and directed for the following :- Note : 1. Modular white cover plate shall be measured and paid separately 2. Rate quoted shall deemed to be inclusive of cost of metal flush box, cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed.

All as per item No 130 above, but for one 3 pin socket outlet 5 Amp on same board complete all as specified and directed.

All as per item No 130 above, but for one 3 pin socket outlet 5 Amp on independent board complete all as specified and directed.

All as per item No 130 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and directed.

S&F Modular Switch 1 way 16 Amps, 1 Module size complete all as specified and directed.

S&F Modular Socket 6 A, 2/3 Pin 2 Module size complete all as specified and directed.

S&F Modular Socket 6A/16 A, 5 Pin, 2 Module size complete all as specified and directed.

S&F Modular Switch 1 way 6 Amps, 1 Module size complete all as specified and directed.

S&F Modular white cover plate with frame, 3 Module size complete all as specified and directed.

S&F Modular white cover plate with frame, 4 Module size complete all as specified and directed.

S&F Modular white cover plate with frame, 6/8 Module size complete all as specified and directed.

S&F in replacement angular lamp holder, metal cased body of brass with back plate including 09Watt LED Bulb in batten fittings, including Plastic square box of required size complete all as specified and directed.

S&F LED bulb 9 watt energy efficient color temp 6500k, lumen 825lm operating voltage 180-260 volt complete all as specified and directed.

S&F ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all as specified and directed.

S&F in replacement LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F in replacement of street light fitting bracket, 1.5 mtr long made out of galvanized iron pipe of 40 mm dia size light grade complete with and incl 02 nos MS clamp made of MS flate iron of 50 x 6 mm size with nut, bolts, washer etc with and incl two coats of aluminum paint over a coat of red oxide primer complete all as specified and directed.

S&F LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with drivr three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F round shape 9 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F in replacement decorative, wall mounting, brushing nickel finish fixture with opal glass diffuser suitable with 9 W LED lamp B22 base complete all as specified and directed.

S&F in replacement surface ceiling light warm white decorative ceiling light 18 watt, cool white complete all as specified and directed.

S&F in replacement LED street light luminaire of 35 Watt capacity, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and incl control gear etc, with and incl making all electric connection complete all as specified and directed.

S&F in replacement sheet Metal enclosure double shutter type for DB’s 240 Volts Single Pole and Neutral 12 way with 200 Amps rated bus bar complete all as specified and directed.

S&F in replacement SPN 5 to 32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

S&F in replacement SP 5 to 32 amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

S&F in replacement VTPN DB 6 way double door type including MCCB TP 63 Amps as incomer complete all as specified and directed.

S&F Taking down submain wiring of size 4/6 sqmm complete all as specified and directed.

M&L for sub main wiring with 2 runs of 6 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and including 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn drawn through & PVC conduit of size 20 mm and above including all conduit accessories & fittings / junction boxes / inspection covers etc, with and including cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note : 1. The cost of concealed conduit & accessories is deemed to be included in quoted rates. 2. The two 2 runs of 6 Sqmm wire and one run of 6 Sqmm wire will be measured as one unit.

All as per item No. 156 above but wiring with 4 Sqmm (3 Runs) complete all as specified and directed.

All as per item No. 156 above but wiring with 6 Sqmm (6 Runs) complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/ dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 3 of SSR 2009 Part-I and connecting to MCBDB’s earth test point all as specified or indicated including testing on completion

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and directed.

S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed.

S&F in replacement Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and directed.

Taking down MCB distributing board with MCCB/ MCB of any size and capacity complete all as specified and directed.

S&F VTPN DB 12 way double door type IP 54 including MCCB TPN 100 Amps as incomer complete all as specified and directed.

S&F sheet metal enclosure double shutter type for DB's 240 volts single pole and netral 8 way with 200 Amps rated bus bar complete including wooden board of required size duly painted with matching clour paint complete all as specified and directed.

S&F sheet metal enclosure double shutter type for DB's 440 volts three pole and netral 4 way with 200 Amps rated bus bar complete including wooden board of required size duly painted with matching clour paint complete all as specified and directed.

S&F TPN 40 to 63 amp rating 440V, 10KA 'C' curve miniature circuit breaker (MCB) complete with connection testing and commissioning complete all as specified and directed.

S&F SPN 40 to 63 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

S&F in replacement DBOX MCB protected Socket plastic base dimension 415 x 375 x 225mm 4 module raise neutral link complete with one single pole MCB 20 Amp 'C' Series 240 VOLT complete all as specified and directed.

M/S Gupta Builders (BID ID -3363981)

Builders Harpal (BID ID -3356634)

REHAN CONSTRUCTIONS (BID ID -3355015)

Shikhar ji Enterprises (BID ID -3356278)

KUSH TOMAR (BID ID -3356008)

UTTRAKHAND BUILDERS (BID ID -3364388)