SPL REPAIR OF TOILET AND BATHROOM, BLDG NO P-48 and P-49 OTM, BLDG NO 1-06-6, 1-06-7, 1-06-12 MT LIVING and OFFICE) and SEWAGE PIPELINE AT UNIT LOC UNDER GE NORTH BINNAGURI

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (including backing), removing serviceable tiles to store and rubbish off the premises including taking down cement plaster.complete all as specified and as directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11Sqm but n. exc. 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in whiter or coloured cement to match as in floor over and including cement screed bed / backing layer of 15mm thick in cement mortar (1:6) complete all as specified and as directed. (Note:- Screed bed shall also deemed to be included in the quoted rate by the contractor).

M&L for glazed ceramic coloured tiles 350x250x7/450x350x7mm thick for work on vertical surface such as skirting, dado, set & jointed in cement slurry and pointed in white or coloured cement to match with and including 10mm thick rendering in CM (1:4) as rough surface on vertical surfaces as backing coat of wall tilescomplete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removal to store of 15 mm bore complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removal to store of 20 mm bore complete all as specified and as directed.

S&F of Tubes, medium grade, 15mm bore, galvanised, with all fittings and fixed complete to wall and ceilings or laid in floors complete all as specified and as directed.

Refixing old 15mm GI tubing and connections on new or old position (walls, ceilling, floor etc) complete all as specified and as directed. (Note:- The serviceable GI tubing obtained from taking down shall be reused)

S&F of Tubes, medium grade, 20 mm bore, galvanised, with all fittings and fixed complete to wall and ceilings or laid in floors complete all as specified and as directed.

Refixing old 20mm GI tubing and connections on new or old position (walls, ceilling, floor etc) complete all as specified and as directed. (Note:- The serviceable GI tubing obtained from taking down shall be reused)

Demolition of RCC as in slab beam lintels,shelves chajjas reinforcement cut as required to facilitate demolition complete all as specified and as directed.

M&L for RCC 1:1.5:3 Type A1 ( using 20 mm graded stone agg) as in slab supported on walls chajjas complete all as specified and as directed.

Material and labour 15-18 mm thick Granite ( Jet Black) work ( table rubbed and polished) in steps , jambs, pillars,floors, window cills, cooking plateforms and like in cement mortar ( 1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screeding in CM 1:4 including full rounding the exposed surfaces complete all as specified.( Note Screed bed shall not be measured and paid separately).complete all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed complete all as specified and as directed.

Dismantling water tanks and removing to store of any capacity of description whether 500/1000 ltrs, complete all as specified and as directed.

S&F 1000 ltrs capacity rotaional moulded polythelene water storage(cylindrical vertical with closed top) triple layer hoisted and fixed in positions all specified in SSR Part I complete all as specified and as directed.

S&F in repairs 20 mm dia PVC ball cock (PVC float valves) complete high pressure with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe and fixed as required to use reducer and check nut complete all as specified and as directed.

S&F in repairs 20mm bore Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all complete as specified and as directed.

Taking down Chowkats with frame n.exc 1.5 Sqm each without taking off shutters from the frame complete all as specified and as directed.

Taking down chowkat with shutter exc 1.5 Sqm and n. exc. 4.00Sqm each and removing from site. complete all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 60/50 x 125/105 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made etc ,complete all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary fitings shall be paid separately)

M & L for providing plain cement concrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

S&F of 100 mm long Stain less steel butt hinges complete all as specified and as directed.

S&F of 150mm long aluminium anodised barrel tower bolt of extruded section and complete all as specified and as directed.

S&F of aluminium handles cast type anodised 150mm of size. complete all as specified and as directed.

M&L for sliding door bolt of 300mm long plate aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

Supply and fixing Factory made single uPVC white colour Three track panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels ) upto 1.50m height made of ( big series ) frame 116x45 mm & sash 46x62mm both having wall thickness of 2.3mm + 0.2mm and single glazing bead / double glazing bead of appropriate dimension . (area of window above 1.75 Sqm ) comprising of uPVC multichambered frame , with inbuilt roller track and sash extruded profiles duly reinforced with 1,60+0.20mm thick galvanised mild steel section made from roll forming process of required length ( shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks , EPDM gasket , wool pile zinc alloy ( white powder coated ) touch locks with hook , zinc alloy body with single nylon rollers ( weight bearing capacity to be 40 kg ) , GI fasteners 100x8mm size for fixing frame to finished wall and necesarry stainless screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of after fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality , complete all as specified and directed by Engineer-In-Charge. (Glass or wiremesh shall be paid separately) (Note:- For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e , in depth & width of profile shall be accepted but no extra payment on this account shall be made.) complete all as specified and as directed.

S&F mild steel work such as window guard bars and similar work conforming to Fe – 290 Grade – E 165 complete all as specified and directed.

Supply and fixing Factory made uPVC white colour fixed glazed window/ventilators made of (small series) frame 47x50mmmullion 47x68mm both having wall thickness of 1.9mm + 0.2mm and single glazing bead of appropriate dimension (area upto 0.75Sqm ) comprising of uPVC multichambered frame and mullion (wherever required),extruded profile duly reinforced with 1.60+0.20mm thick galvanised mild steel section made from roll forming process of required length ( shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimensions, EPDM gasket ,GI fasteners 100x8mm size for fixing frame to finished wall plastic packers , plastic caps, and necessary stainless screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, including drilling of after fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality , complete all as specified and directed by Engineer-In-Charge. (Glass or wiremesh shall be paid separately). (Note:- For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e , in depth & width of profile shall be accepted but no extra payment on this account shall be made.)

M&L for preparation of new surface of steel any description over 10 cm in width or girth not otherwise described two coats of synthetic enamel paint over a coat of red oxide complete all as specified and as directed.

M&L for preparation of old steel and iron surfaces of any description not otherwise described, over 10 Cm width or girth and applying one coat of synthetic enamel paint 1st quality complete all as specified and as directed.

S&F in repairs 15mm dia wall mounted fancy type Bib taps, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed. (Make- CERA Vine Bib cock, Cat Part No- F1020151 or Techno commercially equivalent make as listed in list of makes as approved by GE.)

S&F in repairs15 mm dia CP cast copper alloy angle cock screwd for iron pipe and fixed (Make: CERA Cat no. F1016201 or Techno commercially equivalent make as listed in list of makes as approved by GE.)

S&F in repairs 15 mm bore fancy type concealed stop cock (regular body) cast copper alloy screwed down, high pressure, with crutch or butter fly handle, Make:- CERA Cat part No. F 1015361CH or Techno commercially equivalent make as listed in list of makes as approved by GE.)

S&F in Repairs 10 ltr capacity PVC Twin flushing cistern low level white colour with inlet ball valve float and handle including brackets incl PVC connection 450 mm long, PVC flush pipe of reqd length ,and connections to pipe etc complete all as specified and directed. (Make: CERA COMPASS Cat. No. B1020106 or Techno commercially equivalent make as listed in list of makes.)

S&F in repairs vitreous china squatting pan"Orissa" pattern size 580x440mm white with intgeral foot rests(excluding flushing cistern and flush pipe) with 'P' or 'S" trap fron or back inlet etc including connection to trap tand flushing pipe and provision of cement concrete bedding complete all as specified and as directed in repairs including demolition of existing one

Supply and fixed in repairs white vitreous china wash down water closet pan (pedestal pattern) EWC, with ‘P’ or `S' trap, including fixing bolts, Plastic water closet seat and cover, closed pattern with flat bottom, and mild steel chromium plated or aluminised hinging device, including making all necessary connections complete all as specified and as directed.(Make: CERA CELEB Cat. No. S1053121S or Techno commercially equivalent make as listed in list of makes as approved by GE.)

Supply and fixed in repairs 15 mm bore fancy type bib taps long body (two in one) cast copper alloy single handle and wall flange chromium plated screwed down. Make:- CERA Cat part No. F-1015163 or Techno commercially equivalent make as listed in list of makes as approved by GE.

Supply and fixed in repair CP health faucet (ABS body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 m long flexible tube and ABS wall hook .Make Cera Cat no. F-9090902AB or Techno commercially equivalent make as listed in list of makes as approved by GEs.)

S&F only vitreous china wash basin counter sunk, white oval/rectangular/square shape including waste chain and plug and porcelain stopper but including brackets, waste pipe & CP waste coupling, PVC connection 450 mm long complete all as specified and as directed. CERA CHESTER Cat part No. S2030120 or Techno commercially equivalent make as listed in list of makes.)

S&F in repairs 15 mm bore pillar taps, capstan head, cast Copper alloy, chromium plated, screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.(Make: CERA, cat part : F1019101 or Techno commercially equivalent make as listed in list of makes.)

S&F in repair swivel shower of brass CP with shower arm 125-200 mm size and wall flange for fixing with 15 mm bore GI pipe complete all as specified and as directed.(Make: CERA Cat No. F7020111AB or techno commercially equivalent make as listed in list of makes.)

Supply & fixed in repair Towel Rail 600 long chromium plated , including all necessary fittings, connections etc.Make – Cera Cat Part No F5003103 or Techno commercially equivalent make as listed in list of makes.)

Supply Soap Holder chromium plated , including making all necessary fittings, connections etc complete all as specified.Make – Jaquar Cat Part No CAN 1135N or Techno commercially equivalent make as listed in list of makes.)

S&F in repairs PVC connection pipe 15mm size with P&T nuts of length 450mm complete all as specified and as directed.

S&F in repair Grating doom 125 mm dia with waste hole/without hole of PTMT (Minimum weight 40gms) complete all as specified.

Taking down cement plaster on wall / Ceiling of any desription incl racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Demolition of brick work built in cement mortar of any description,etc complete all as specified and as directed.

M&L for brick works with fly ash bricks straight or curved on plain exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed..

M&L for rendering 5 mm thick cement plaster on ceiling cement mortar (1:3) finished the surface even and fair complete all as specified and as directed.

M&L for rendering 15 mm thick cement plaster on fair face of surfaces of brick work or concrete surface in cement mortar (1:6) finished the surface even and fair complete all as specified and as directed.

M&L for 15 mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers first layer of 10 mm thick and top layer of 5 mm thick plaster with water proofing compound @ 200ml per bag of cement or as per manufacturer's instructions finishing the surface even & without using extra cement complete all as specified and as directed. (NOTE : Liquid Water Proofing Compound shall be measured and paid separately under relevant item of this Schedule 'A')

Supply only liquid water proofing compound complete all as specified and as directed.

M&L for applying two coats of exterior emulsion paint (weather coat) over a coat of exterior primer on a new plastered surfaces of walls including projection, RCC jalies & post etc including necessary preparation of surfaces complete all as specified and as directed.

M&L for for preparation of newly ceiling plastered surfaces and applying three coats of whitewash on ceiling complete all as specified and as directed.

M&L for preparation of newly plasterd surface and applying two coats of oil bound distemper over a coat wall care putty over plastered surfaces including priming the surface complete all as specified and directed

M&L preparation of old plasterd surface and applying two coats of oil bound distemper over a coat wall care putty over plastered surfaces including priming the surface complete all as specified and as directed

M&L for preparation of Old decorated surface of ceiling and applying two coats of White wash complete all as specified and as dirtected

M&L for preparation of old plastered or unplastered surfaces of walls including cornices, pilasters and other wall features etc by washing rubbing down and stopping and applying and finishing the walls with premium acrylic smooth exterior weather proof paint with silicone additives of required shade (luster paint) applied @1.43 ltr/10 Sqm over and including priming coat of exterior primer applied @0.90ltr/10 Sqm complete all as specified and as directed.

Demolition of cement concrete (un-reinforced ) in ground floors and pavings n.exc 15 cm thickness (below or above ground level) all as specified and as directed.

M&L for 75 mm thick cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate in plinth protection finished fair and even without using extra cement including forming necessary joints 12 mm wide to the full depth of PCC at every 3 metres and every change of direction and filling the same with & including bitumen and sand 1:3 by weight of grade 'A' complete with and including necessary form work etc complete all as specified and as directed.

M&L for providing plain cement concrete type B0 1:2:4 with using 12.5mm graded stone aggregates in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

Demolition of cement concrete (unreinforced) roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and as directed.

M&L for water proofing treatment to sunken floor with the following course of treatment / specification :- (i) Cleaning top surface of floors / slabs and laying 50mm thick (avg) PCC of grade M10 (Nominal mix) , mixed with WPC as per manufacturer's instruction laid in slope 1:20 towards spouts including coveting corners. (ii) 15mm thick plastering in CM (1:4) on sides mixed with WPC as per manufacurers instruction. (iii) Applying 1st layer of slurry @ 0.488 kg/ Sqm mixed with acrylic based polymer modified cementious compound @ 0.253 kg / Sqm , this layer shall be allowed to air cured for 4 hrs . ( iv) Applying 2nd layer of slurry @ 0.242 kg/ Sqm mixed with acrylic based polymer modified cementious compound @ 0.126 kg / Sqm , this layer shall be allowed to air cured for 4 hrs followed with water curring for 48 hrs. (v) Applying a coat of industrial bitumen 85/25 penetration @ 1.50 kg/Sqm on plastered and concrete surfaces. (vi) Providing 150 micron thick polyutethene paint in two coats ( each of 75 micron measured dry surface over a coat of PU primer including prepration. (Make of PU primer- Dek guard EP - 302 of Fosroc or techno commerically equivalent make as listed in list of make as approved as Make of PU paint- Dek guard PU or techno commerically equivalent make as listed in list of make as approved (vii) Sunken floor shall be tested for water tighness by filling water for 72 hrs before and after treatment work is carried out and ensure that no leakage / seepage exists. (ix) Sunken portion shall be filled with lean concrete of grade M 7.5 stone agreegate. (Note : Treatment shall be carried out by authorised applicator approved by the manufacturer.)

Taking down or demolition and breaking up drain pipes(SGW,AC,PVC SWR)75/ 100 mm dia complete all as specified and as directed.

S&F 75 mm PVC(SWR) pipe socketed in any length with rubber ring joints,laid in trenches or in floors complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) pipes single sockets in any length with rubber ring joints fixed to wall or laid in floor complete all as specified and as directed.

S&F PVC(SWR) 75mm bore bends, diminishing pieces or tapers complete all as specified and as directed.

S&F PVC(SWR) 110 mm bore bends, diminishing pieces or tapers complete all as specified and as directed.

S&F of PVC (SWR) floor trap, plain with CP grating including jointing with solvent cement outer dia 75 mm cement concrete (1:2:4), type B1 including complete all as specified and as directed.

Taking down existing tarfelt including tiles, lime cement concrete & screed bed complete from roof surfaces including parapets and lowering and removing the same to a distance exc. 50m and n. exc. 100m including roughening of old concrete surface of roof by wire brushing and cleaning the surface to remove all loose dust etc complete all as specified and as directed.

M&L for 10mm thick screed bed or bedding layers in cement mortar (1:4) in order to maintain proper slope over existing roof surfaces for laying acrylic polymer modified, fibre reinforced waterproof coating finished even and smooth without using extra cement complete all as specified and as directed.

M&L for providing and applying single component acrylic polymer modified, fibre reinforced waterproof coating in 4 coats of application (a) applying primer coat with Primer @ 0.3 kg /Sqm (b) over priming coat applying roof guard as specified below or manufacturer instructions with fibre reinforcement a width of approx 1m @ 0.75kg/Sqm on the flat or vertical surfaces over parapetwall and ensure that there are no bubbles of creases. Overlapping of the fibre is a minimum of 50mm and allow this coat to dry for a period of 2-6 hrs depending on the atmospheric condition. (c) Applying second coat @0.75Kg/Sqm (d) Applying final coat of primer @ 0.08kg/Sqm after 2nd coat has dried properly. (Note : Water Proffing treatment shall be carried out by authorised applicator approved by the manufacturer.)

M&L for Cement concrete type 1:3:6 type C2 using 40 mm graded stone 100 mm thick as sub base complete all as per specified and as directed

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade complete all as specified and as directed

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed

M&L for machine cut kota stone slab flooring 18 to 20mm thick over 15mm thick cement screed base(1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 18 to 20mm thick as in skirting over 10mm thick cement screed base(1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

S&F Mild steel TMT bars 6mmto 10mm dia , cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.90 mm dia. complete all as specified and as directed.

S&F Mild steel TMT bars 6to 8mm dia , cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.90 mm dia as in stirrups complete all as specified and as directed.

M&L for Brick work with flyash bricks old size straight half brick work or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:4 complete all as specified and as directed

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for including removing of demolished material from site complete all as specified and as directed.

M&L for Reinforced Cement Concrete type B0 1:2:4 (12.5 mm aggregate (Nominal mix) using 20 mm graded stone aggregate as in Chajja complete all as specified and as directed

M&L for RCC type B, 1:2:4 (using 20mm graded aggregate) Slabs supported on walls, beams Nominal mix as in and columns in floors,roofs, landings balconies, canopies, deck slabs and inshelves and the like complete all as specified and as directed.

Use and waste of formwork to chajjas and similar items including edges. complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

M&L for precast steel frames of size 125 x 60mm for door with one or more rebates of 1.25mm thickness including necessary fittings, lugs, hinges, lock strike plate, flat iron hold fast etc complete all as specified and as directed.

S&F Flush shutters, 30mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed

S&F 30mm th, factory made 2nd class HW glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete all as specified and as directed.

S&F Sheet glass, 3 mm ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane all as specified and as directed.

S&F Butt hinges medium weight, cold rolled mild steel 100 mm size complete all as specified and as directed.

S&F Aluminium anodised sliding door bolt, with hasp & staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections 200 mm long. complete all as specified and as directed.

S&F Stainless steel wire cloth, 0.50 mm nominal dia of wire and avergae width of aperture 1.00 mm and fixed with stainless steel wire staples. complete all as specified and as directed.

S&F factory made pressed steel windows of standard size and section as shown on HQ CE Siliguri Zone Drawing No CESZ/2018/TD-07, Sheet 1/3 to 3/3 with double shutter i.e. glazed & wire gauged shutter including all fittings and fixture like MS hold fast, box hinges, handles, MS tower bolts, stoppers, MS guard bar/grill etc complete including one shop coat of anti corrosive zinc chrome primer and taking down of old existing one complete all as specified and as directed.Notes:- (a) Rate quoted shall be deemed to be including of all fittings fixtures . (b) Wire mesh and painting shall be measured and paid separately under relevant items of this schedule. (c) PCC (1:3:6) type C1 to be filled in chowkats frame and paid under relevant item of this schedule.

S&F for steel ventilators with top hung shutter including hinges, steel peg stay complete all as per drawing No CESZ/2018/TD-07, Sheet 1/3 to 3/3 and as specified including taking down old steel ventilators complete all as specified and as directed

M & L for preparation of old treated surface of wall by brooming down or steel wire brushing; scrapping down smoke root, moulds, moss and efflorescent salts and treating oil and greasy spots and applying two coats of white wash on old decorated surfaces of wall including washing froors, cleaning glass, joinery, electrical fittings, wiring etc of drops and splashes complete all as specified and directed.

M&L for preparation of newly plastered surfaces on wall / ceiling / chajjas and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over new/old surfaces as per the manufacturer instruction and all coats including primer to be applied Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and as directed.

M&L for complete removal of existing treatment of old decorated treatment on wall / ceiling / chajjas by scrapping with true care wall sander : L-01/H-01 ( having mechanical vacuum mechanism ) having RPM not less than 1500, sanding pad of 80 grit having dia 7"/9" to make the surface free from dust, loose paints etc. or equivalent makes viz Xpress sanding machine having sanction vacuum bag or by manual scrapping tools where mechanical removal is not possible and filling cracks, holes etc complete and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over new/old surfaces as per the manufacturer instruction and all coats including primer to be applied withAllow 6-8 hrs to dry the surface in subsequent coats of paint

M&L for PCC 1:2:4 Type B-1 (20mm graded aggregate) provinding as in kerbs,filling hollow space in chowkhat,copings, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed.

S & F in repair 15 mm bore Bib taps, chromium plated fancy type, screwed down, screwed for iron pipe or for brass ferrule. complete all as specified and as directed.

S & F 15 mm bore Stop valves, chromium plated fancy type screwed both ends for iron pipe or for unions. complete all as specified and as directed.

S & F in repairs Vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm size including cutting for and pinning ends of brackets or erecting stand complete all as specified and as directed.

Supply and Fix in repairs 10 Litres, PVC, valve less, syphonic action type, Flushing Cistern, high level, white inlet, ball valve, float, chain and pull, and brackets including PTMT PVC connection 600mm long complete all as specified and as directed.

S & F 500 litres capacity Rotational moulded polyethylene water storage tanks (triple Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including disconnectiong of existing tank and removing to store complete all as specified and as directed

S&F in repair Toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed

S & F 110 mm bore PVC (SWR) bends of any radius with access door. complete all as specified and as directed.

S & F 100mm PVC (SWR) junction single, (single T) equal or unequal complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) bends of any radius with access door. complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified and as directed.

S & F 75 mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed.

Demolition & breaking up drain pipes( salt glazed ware, AC or reinforced concrete) set in cement mortar, internal dia of pipe 150mm

Demolition & breaking up drain pipes( salt glazed ware, AC or reinforced concrete) set in cement mortar, internal dia of pipe 200mm

Excavation in trenches n.exc. 1.5 M wide and n.exc. 1.5 m in depth for foundation etc in soft/loose soil complete all as specified and as directed

M&L for 150 mm dia Reinforced concrete pipes, class NP2, laid and jointed completewith collars all as specified and as directed.

M&L for 200 mm dia Reinforced concrete pipes, class NP2, laid and jointed completewith collars all as specified and as directed.

S&F for Reinforced concrete pipe (SWR) bends any radius fixed to Pipes/Steel Gutters etc complete all as directed by(Bore of bend 150mm)

S&F for Reinforced concrete pipe (SWR) bends any radius fixed to Pipes/Steel Gutters etc complete all as directed (Bore of bend 200mm)

S&F for RCC branch piece,single (single y )equal or unequal radius fixed to Pipes/Steel Gutters etc complete all as directed (Bore of 150mm)

S&F for RCC branch piece,single (single y )equal or unequal radius fixed to Pipes/Steel Gutters etc complete all as directed (Bore of 200mm)

M & L, Cement concrete 1:4:8 type D-2 bed to 200mm dia bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in complete all as specified and as directed.

M & L, Cement concrete 1:4:8 type D-2 bed to 150mm dia bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in complete all as specified and as directed.

M & L for Cement concrete 1:4:8 type D2 ( using 40mm graded aggregate ) as in foundation filling and mass concrete complete all as specified and as directed.

Returning, filling in including spreading, leveling, watering & well ramming in layers not exc. 25 cm complete all as specified and as directed.

M&L for removing excavated material soil beyond 50 m and upto a total distance of 250 m depositing where directed at a level n exc. 1.5 m above the starting point all as specified and as directed.

M&L for PCC 1:2:4 type B1 as in surface channel, benching and drains in manholes,complete all as specified and directed.

M&L for Precast RCC 1:2:4 type B1 ( using 20mm graded aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain face complete all as specified.

M&L for Cutting into existing manholes for connecting new drains, for internal dia of 150mm pipe and making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains, for internal dia of 200mm pipe and making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed.

INTERNAL ELECTRIFICATION Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

Taking down the existing unserviceable main switch/ cut out/ DBs of any type/capacity/description as existing at site including making good the disturbed surfaces to match with the existing finishes complete all as specified and as directed

M&L for point wiring with 1.5 Sqmm single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with multistranded copper conductor with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI Marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI Marked) with proper colour coding as earth continuity conductor connected to common earth dolly, Mild steel steel sunken terminal box of appropriate size suitable for switch/ fittings concealed in walls, with back plate, top cover fixed flush to wall for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sunken boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles all as specified and as directed for the following :- (a) One light point controlled by one way switch 5/6 amps.

All as per item No 134 above but One ceiling fan/Exhaust fan point controlled by one way switch 5/6 amps.

All as per item No 134 above but One socket out let 5/6 amps point on the independent board

All as per item No 134 above but One socket out let 5/6 amps point on the same board

All as per item No 134 above but wiring with 2.5 sq mm single core multistranded copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified and directed

S&F switch piano single pole flush type 5amp, 230 volts one way complete all as specified and as directed

S&F socket 2 in 1, 5 Pin 5/6 amps, white ivory finish flash type complete all as specified and as directed

S&F ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and directed.

S&F Switch socket combination 2 and 3 pin, 5/15 amps, multipurpose flush non shutter, non inter locking type white ivory finish with, complete all as specified and as directed

S & F lamp holder, insulated body, with back plate suitable for batten/angle fittings complete all as specified and directed.

S&F LED white glass Lamp 1x9 Watt 230V Base-22 complete all as specified and directed.

S&F for LED light 1X18 W (or nearest next higher wattage) (4feet), 5700K, wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified and as directed

S&F MCB distribution boards (DBs) with sheet metal enclosure, double door, IP 43 protection, 240 Volts, 4 way, single pole and neutral, with 200 Amps rated copper bus bar (as per OEM), neutral link, earth link earthing studs, suitable for fixing MCBs, without MCBs fixed flush to wall/other surface including taking down old existing one complete all as specified and as directed.

S&F in replacement MCB SPN 230 volts suitable for fixing on MCB DB of capacity 6 to 30 Amps complete all as specified and as directed

S&F MCB, Single pole, 5 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete with and including taking down old unsv one as specified and as directed.

Taking out old unserviceable GI pipe of 25mm bore from site complete all as specified and as directed Note: The excavation and earth work shall be mesured and paid separately under relevant item of Schedule

Supply and lay pipe galvanized "Medium class", including fittings 25mm fixed complete to walls and ceiling or laid in floor complete all as specified and as directed

Supply and fix Gun metal, glode gate valves with iron wheel head of 25mm dia bore complete with all accessories all as specified and as directed

Supply and fix Gun metal globe Gate valves with iron wheel head of 20mm dia bore complete with all accessories all as specified and as directed

M&L for cutting existing GI pipe alteration or addition of upto 40 to 50 mm dia bore for inerstion of reducer Tee complete with all accessories all as specified and as directed

Removing surplus soil to a distance not exc. 50 mtr and depositing where directed at a level not exc. 1.5 mtr above the starting point complete all as specified and as directed.

S&F of Modular switch, single single pole, one way, 6 Amp, 1 Module, 230 volt, ISI marked Complete all as specified and as directed

S&F of Modular switch, single single pole, one way, 16 Amp, 1 Module, 230 volt, ISI marked Complete all as specified and as directed

S&F of Modular shuttered Socket outlet 5 PIN, 6 Amp, 2 Module, 230 volts, ISI marked Complete all as specified and as directed

S&F of Modular shuttered Socket outlet 6 PIN, 6/16 Amp, 2 Module, 230 volts, (ISI marked) Complete all as specified and as directed

S&F of stepped type modular electronic fan regulator 120 watt 2 module suitable for 1200/1400 mm sweep energy saving fans, ISI marked Complete all as specified and as directed.

S&F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 35 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0. 193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 25mm dia, 90 mtr long bend to required shape complete incl removal of old unsv fitting all as directed

S&F sheet metal enclosure for 8 way Distribution Boards (DBs), double door, single pole & neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB's/Isolators Complete with and including taking down old unsv one all as specified and directed incl taking down the existing unserviceable main switch/ cut out/ DBs of any type/ capacity/ description as existing at site including making good the disturbed surfaces to match with the existing finishes all as specified.

S&F MCB TPN 415 volts suitable for fixing in MCB DB of capacity 40/60 amps complete all as specified and as directed.

M&L for SPN enclosure with two pin and earth plug and socket with 240 volts 20 Amps SPN MCB including removal old unsv one complete all as specified and as directed.

Material and labour for earthing complete with galvanized steel plate electrodes of size 600x600x6mm thick burried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised iron strip 25x 4 mm earth lead by means of nuts, bolts, checknuts and washers including 15mm bore galvanized iron pipe, medium grade for protection of earth lead upto the length of 7.5 meter towareds test terminal and 20mm bore galvanized iron pipe, medium grade for watering, and providing of charcoal and common salt in alternate layers, including necessaryearth work in any type of soil and including PCC 1:2:4 with provision of wire mesh and funnel, complete all as shown in elevtrical plate No 3 of SSR Part-I including testing on completion and taking down old one complete all as specified and as directed

Taking down carefully Ceiling fan from its original position and refixing/ hanging after B/R plaster work complete all as specified and as directed

M&L painting of ceiling fan complete, in situ with synthetic enamel paint by spraying including filling cavities with filler one coat after cleaning all dust etc, all as specified and as directed.

Taking out old unserviceable cable of any size carefully from trenches ofter disconnecting electric connection, GI pipe protection, with and including separating serviceable bricksa & set aside and removing un-serviceable bricks from site complete all as specified and as directed. Note: The Excavation and earth work shall be measured and paid separtely under relevant item of Schedule.

Supply, laying, jointing & testing in trenches or passing thorugh pipe, 100 volts grade, XLPE insulated PVC bedded, galvanized steel strip or wire armoured LT electric power UG cables, heavy duty with stranded aluminium conductor of cross sectional area 16 Sqmm 4.0 core with and including all fixing & connecting accessories such as Alluminium cable lugs, cable gland, nut bolts, washer etc complete as specified and as directed. (Note: Earthwork & Excavationh, GI pipe, bricks for protection etc shall be measured and paid separately under relevant items of this schedule 'A')

All as per item No 168 above but, for 10 Sqmm and 2 core

Supply and lay dry river sand filling for under ground cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and as directed.

Supply and laying sub class B brick of size 25cm x 12.5xmx7.5cm for protection of UG cable with width equal to length of bricks as mechanical protection laid dry and flat complete all as specified and as directed

Horizontal boring of holes, under road/pavement/ hard standing etc., not excedding 10 metres in length, in any type of soil, suitable for passing through up to 50mm bore, galvanised steel tubing complete all as specified and as directed.

Supplying and fixing Galvanised mild steel pipe/ tubing, light grade complete with all fittings of 32 mm bore dia, laid in trenches/ under roads, fixed to poles/ walls with mild steel clamps, bolts, nuts and washer as in cable protection complete all as specified and as directed

Shri Amarnath Sah (BID ID -3382658)

BBKundu (BID ID -3381142)

L. B. SHARMA (BID ID -3382436)

samrat saw mill and joinery workshop (BID ID -3381728)

SHRI SATPAL SINGH (BID ID -3381503)

M/S SINHA ENTERPRISE (BID ID -3381309)

N K Construction (BID ID -3379984)