Providing and Erecting to LED Flood Street Light Fittings of Dam Top Light and Bump Light at Juj Dam.

Name of work:- Providing and Erecting to LED Flood Street Light Fittings of Dam Top Light and Bump Light at Juj Dam

Sr.No Qty Description Item Rate Per Amount

Supplying and erecting Flexible PVC insulated multi strand multi

Rupees FourtySix Paise

1 588.00 core 1.1 kv grade ISI marked copper wires of following size to 46.46 Mtr.

be erected as directed. FourtySix Only

(e) 1.50 Sq.mm 3 core round PVC sheathed

Supplying and erecting LED street light / Flood light fittings with

High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name engraved or

2 embossed 160 to 270 V,Power Factor more than 0.95, THD <

10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire

efficacy> 100 lumens/watt . LED driver efficiency > 85 %.(

fittings required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and

,Light must have 440VAC line supply with over-voltage Rupees Five Thousand

84 protection. 5976.17 Nine Hundred SeventySix Ea.

Paise Seventeen Only

(ii) above 48 to 60 Watts Cat-lll

providing and erecting Miniature circuit breaker single pole 6A

to 25A suitable to operate on 240 V A.C. system and having Rupees One Hundred

3 84 breaking capacity 10 KA to be erected in existing box. 112.11 Ea.

Twelve Paise Eleven Only

confirming to IS 8828/1996 with ISI Mark (B) cat-(III)

Providing & erecting 415 V MCB Four Pole for Motor & Rupees Seven Hundred

4 1 Inductive Load (C Curve) having 10KA breaking capacity & 737.30 ThirtySeven Paise Thirty Ea.

confirms to IS :8828 in existing box having following capacity Only

(c)63 Amp. cat- iii

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall Rupees One Hundred

5 1080.00 with necessary clamps or in existing trench / pipe of following 153.52 FiftyThree Paise FiftyTwo Mtr

size of cables Only

(A) 4 core 16 Sq. mm

Making trench in soft soil of suitable width of 90 cm deep for

laying cable or locating the fault all over the run and back filling Rupees FiftyFive Paise

the same and making the surface as normal ground. FiftyFive Only

Making trench in Hard Murrum / Tar Road of suitable width of

90 cm or required depth for laying any size of cable or locating

Rupees SeventyFour

7 371.00 the fault all over the run and back filling the same and making 74.74

the surface as normal ground. Paise SeventyFour Only

Providing & laying approved make Double walled corrugated

pipes (DWC) of polyethylene(conforming to IS 14930 II )with

Rupees SixtyTwo Paise

8 1030.00 necessary connecting accessories of same material at required 62.62 Mtr

depth in existing trench for laying of cable. below ground / SixtyTwo Only

road surface for enclosing cable

(A)50 mm outer dia

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high Rupees Fifteen Paise

9 336 pressure tool & connected to switchgear terminals with 15.15 Ea.

brass/cadmium plated nut bolts in an approved manner.

Supplying and erecting approved make Octagonal pole made

from HR sheet steel. The pole should be made as per IS. and

shall be coated with hot dip galvanizing as per IS

2629/2633/4759, suitable suspend local wind speed with

integral Junction box consist of terminal plate of min 6mm

10 Hylam sheet, standard profile 35mmX7.5mm Din-Rail for MCB

Mounting, stud type terminal and arrangement for cable

termination to be erected With Suitable foundation (Included)

as per details given by manufacturer considering site

(D) 6 Mtr. Long 70 mm Top X 135 mm bottom dia, 3 mm

thickness with 200mmX200mmX12mm base plate, 4-M20 Bolts Rupees Eight Thousand

42 and 600mm long with necessary G.I. J Bolts .Approx Pole 8192.11 One Hundred NinetyTwo Nos.

weight 59 kg Paise Eleven Only

Supplying and erecting Street light pole bracket comprising

main B Class GI pipe of 4.2 cm/require outside dia. complete

with suitable B Class G.I. sleeve tubing of approx. 45cms.length

and suitable for 76.5mm/80mm/require size of pole top having

nuts and bolts for fixing the brackets and having spread of 0.5 Rupees Six Hundred

11 42 mtr. Length with 110 deg.with vertical plane and suitable welded 622.16 TwentyTwo Paise Sixteen Nos.

stiffener reducer and nipple with check nut complete painted Only

with one coat.of Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of arms.

[B] Double Arm Bracket 0.5 Mtr 0

Replacing Old and u/s by Supplying & erecting approved make

IP 55 grade Company fabricated Timer Panel of following

capacity for switch On-Off street lights on time scheduling

basis made from 16G CRCA sheet duly epoxy power painted

inside and outside with hinged doors and locking arrangement Rupees Seventeen

12 1 consisting of suitable size of 4 Pole MCB and 4 pole contactor 17059.91 Thousand FiftyNine Paise Ea.

(cat-III)with analog time switch, auto manual switch of same NinetyOne Only

make and suitable input and output Bakelite terminals and with

door earthing approved by Engineer in charge.

Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot

dipped G.I.Pipes having Outer pipe dia of 50mm having 80-

200 Micron galvanising, Inner pipe dia of 25 mm having 200-250

Micron galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for following

type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate including

13 value of earth resistance of installation duly stamped and signed

by agency and officer Incharge has to ensure the value of

earthing resistane mentioned in test Certificate) & having back

filling compound of (B) Inner chemical (CCM Compound)-

Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017,

Voltage drop:- < 1 volt at no load & dry form, Sulphar content:-

<2%(C) Back fill Compound :- Earthing compound should be

capable to retain moisture for long time Necessary test report

must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil Rupees Four Thousand

3 Length of pipe - 1 Mtr 4591.46 Five Hundred NinetyOne Ea.

Back filling compound - 1 Nos Bag of 15 Kg. Paise FourtySix Only

Providing and erecting HOT deep Galvanised iron strip wire 8 to

16 SWG. Rupees SeventySeven

Paise SeventySeven Only

I/We am/are willing to carry out the work at ……………………………………………% above/below percent (shouldbe written in figured

and words) of the estimated rates mentioned above. Amount of my/our tender works out as under.

Estimated amount Estimated amount

Put to tender Rs______________ Put to tender Rs______________

Deduct : ___________ % Above RS__________ Deduct : ___________ % Below RS__________

*(Please strike out whitchever is not applicable).

Note 1 – All work shall be carried out as per public works department handbook and other specification of Division ot as directed.

Note 2 – All the columns is schedule should be filled in ink and the total of the entries in the last column should be struck by the

contractor under his signature.

Note 3 – Rates quoted include clearance of site (prior commencement of work and at its close ) in all respects and hold good for

work under all conditions, site, moisture,weather etc.

Note 4 – To be continued on additional sheets, if found necessary.

Note 5 - The rates quoted by the Contractor must be inclusive of all taxes prevailing on due date of bid submission except GST.

However, any subsequent changes in the tax structure by Government after due date of bid submission will be compensated (+/-) on

availability or submission of actual documentation. Contractor will have to intimate Engineer regarding changes occurred in the tax

structure after bid submission. If the contractor fails to provide such information and if any financial obligation may arise due to

change in tax structure, same will be recovered from the contractor. GST will be paid separately on the bills. Hence, it is the

responsibility of the contractor to pay the GST to the concerned Authority.

Deputy Executive Engineer Executive Engineer

Electrical Sub Division Ukai Division No