SPL REPAIR TO BR AND EM WORKS IN CERTAIN BLDGS ALONGWITH PROVN OF OTHER REV MINOR IN VARIOUS UNITS AT SUNDERBANI UNDER GE (N) AKHNOOR

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premises complete all as specified and as directed by Engineer-in-Charge.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square/ractangular) area of each tiles exceeding 0.06 Sqm but n.exceeding 0.11sqm as in floors, set and jointed in neat cement slurry and pointed in coloured cement laid over & including 15mm thick screed bed or bedding layer in cement mortar 1:4, complete all as specified and directed.

Glazed ceramic tiles 450 x 300 x 7mm thick / 600 x 300 x 7mm thick (coloured) on vertical surfaces such as skirtings, dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles laid over & including 15 mm thick screed bed in cement and sand mortar 1:6, complete all as specified and directed.

Description all as per item No.04 above, but in vertical surfaces such as skirting/dado fixed over & including 10 mm thick rendering in cement and sand mortar 1:4, complete all as specified and directed.

Taking down chowkhat or frames of door/ window with shutters (Without taking off shutter from the frame) exc 1.50 m and n.exc 4.00 Sqm each, complete all as specified and directed.

Taking down chowkhat or frames of door/ window with shutters (Without taking off shutter from the frame) n.exc 1.50 sqm complete all as specified and directed.

Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube, supplying and fixing in opening as per specification and drawing, complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site, complete all as specified and as directed.

Factory made Pressed steel frames of size 125x60mm made out of PBI sheet 1.25 mm thick for doors with one or more rebates including necessary fixing lugs, hinge,lock strike plate etc.complete including bottom of each chowkat to be welded with 02 Nos 25x3mm thick flat iron projecting 10cm on either side & tarring back of chowkats and holdfasts with & including PCC 1:3:6 type C-0 (using 12.5mm graded crushed stone aggregate) as in back filling of pressed steel frame, complete all as specified & directed.

35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated, complete all as specified.

35 mm thick, 2nd class hard wood , glazed & skeleton factory made shutters, open rebated & prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.20(a) complete all as specified.

Steel windows/ventilator (Box type) factory made with double shutter with or without devetailed bar ( glass & gauged shutter) of size 79mmx39mm,16 gauge rectangular tubular frame with side hung shutter with glazing bars 12x3mm flat iron incl box type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts in each shutter 100mm long with & including 8mm square bar grills, complete all as specified & as shown on drg No. CEUZ/TD/1269/2008 Sh No 1/1 to 1/3 . Note:-(a) Fixed type glass panes shutter if any provided in above same window shall be measured and paid separately & area of these fixed shutter shall be deducted from total area of box type window for payment purpose. (b) Sheet glass/ wire cloth shall be measured & paid separately under respective item

Description all as per Item No.13 above, but only fixed glass pane shutter without glazing bars.

PCC 1:2:4, B-1 (20mm graded crushed stone aggregate) as in copings, hold fasts, plinth band, bed blocks, benching and like slightly rounded or chamfered angles as directed including necessary form work, complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clips and providing and fixing new ones glazed with oil putty fixed with beads complete all as specified and directed.

03 mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified.

Figured glass pin headed type, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified.

Galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

Preparation new steel and iron surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as speciified and directed.

Preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer,complete, all as specified.

Preparation of old steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

100mm butt hinges medium weight cold rolled mild steel, complete all as specified.

250mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified and as directed.

200mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified.

Aluminium handle cast type anodised of size 150mm long ISI marked complete all as specified.

300mm Mild steel ordinary rat tail rod pattern springs including roller and roller plate fixed in repairs complete all as specified and directed.

25 mm dia stainless steel curtain rod complete with stainless steel bracket and side caps fixed in position by drilling holes in wall and fixed the bracket with rawl plug and SS screw, fixed in repairs all as specified and as directed.

Demolition of brickwork or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stonework, complete all as specified and as directed.

Brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified.

Description all as per item No.30 above, but except bricks, all as specified and directed.

Brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 in half brick thick, complete all as specified.

Taking down cement plaster of any description on stone or brick walls etc. including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

Rendering 15 mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces and finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 15 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement, complete all as specified and as directed.

Rendering 5mm thick cement plaster with cement mortar(1:3) on concrete surface as in ceiling finished even and smooth without using extra cement, complete all as specified and as directed.

Preparation of newly plastered surfaces of ceiling and applying three coats of white wash, complete all as specified.

Preparation of old plastered surfaces of ceiling and applying one coat of white wash, complete all as specified.

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whitening primer complete all as specified and as directed.

Preparation of newly plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistant primer complete, all as specified and directed.

Preparation of old painted surfaces by washing, rubbing down and stopping of distempered and painted walls and applying one coat of oil bound distemper complete all as specified and as directed.

Description all as per Srl Item No. 41 above, but one coat of cement base paint.

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified.

75mm thick PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection laid in bays complete including finishing the surface of concrete topping even & fair, complete all as specified.

75mm thick PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in subbase of floor/hardstanding etc, finishing surface even and rought to receive topping layer, complete all as specified.

Chequered cement concrete tiles 30cmx30cmx25mm thick laid & jointed with grey cement and pointed with cement slurry and pigment to match shed of tiles, laid over and including 15mm thick screed bed in CM 1:6,,complete all as specified and directed.

PCC 1:2:4, B-2 (40mm graded stone aggregate) as in surface channels and drain etc including necessary formwork complete all as specified and directed.

Extra for forming fair finished to drain channel not exc 30 cm inner girth in cement concrete using extra cement complete all as specified and directed.

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc complete all as specified and as directed.

Taking up or down steel tubing and connections, 20 mm bore fixed on walls, floors or ceiling etc complete all as specified and as directed.

Refixing old steel tubing and connections of 15mm bore in new or old position (Walls, ceiling, floors etc.) after cleaning including provn of new fittings all as directed.

Refixing old steel tubing and connections of 20mm bore in new or old position (walls, ceiling, floors etc.) after cleaning including provn of new fittings all as directed.

Mild steel galvanized steel tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete of bore15 mm all as specified and directed.

Mild steel galvanized steel tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete of bore 20 mm all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, cutting not exc 10 cm girth Stone concrete block or slab walls all as directed.

Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) 3 layered hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified and directed.

Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20 mm dia (minimum weight 210 gms) complete all as specified.

20mm bore gun metal glove or gate valve with iron wheel head screwed both end for iron pipe and fixed in repairs, complete all as specified and as directed.

Vitreous china wash basin, white, flat back, size 550x400mm with full padestal with & including CP waste fitting & waste pipe porcelain stopper a pair of CI brackets fixed in repair complete all as specified and as directed by Engineer-in-Charge. Cat Part No-10100 of Hindware for Wash basin or its equivalent cat part of make specified in list make as approved by GE.

Vitreous china wash basin, white, ovel shape, size 550x400mm including CP mixer for mixing hot and cold water for pipe of bore 15mm, waste fitting chromium plated brass, chromium plated steel chain and rubber plug, porcelain stopper, a pair of CI brackets, waste pipe etc., fixed in repairs complete all as specified and as directed by Engineer-in-Charge. Cat Part No. 10036 of Hindware (Model-Windsor) or its equivalent in Neycer, Cera & Parryware.

PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets fixed in repairs, complete all as specified and directed.

Angle/ Stop valves (Concealed type), cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions for 15mm bore pipe fixed in repairs, complete all as specified and directed.

Tubular towel rail 60cm long 20mm dia D type aluminium anodised incl necessary brackets, fixed, complete all as specified and directed.

Bib tap 15 mm bore with flange, Brass CP, fancy type. with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed in repairs, complete all as specified and as directed.

PVC connection 15mm size with PTMT nuts on both ends of length 450mm fixed, complete all as specified and directed.

Brass chromium plated shower rose 125mm size with or without swivel joints, with arm any size, including fixing to steel pipe or union complete all as specified and directed

Pillar taps 15mm cast copper alloy CP, fancy type with capstan head, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nut, screwed for iron pipe 15 mm bore.fixed in repairs, complete all as specified and as directed.

Vitreous china wash down water closet pan pedestal pattern in white colour excluding seat cover, flushing cistern and flush pipe fixed in repairs complete all as specified and directed. Cat Part No-20011 (SLICK) of Hindware or equivalent cat part of make specified in list of makes as approved by GE.

Vitreous china squatting pan "Orissa Pattern" size 580 x 440 mm in white colour with integral foot rest incl lime mortar incl making good dismantled floor with PCC 1:2:4 B-0 (using 12.5mm graded crushed stone aggregates), 'P' trap fixed in repairs complete all as specified and directed. Cat Part No-20042 (ORISSA PAN (ECO)) of Hindware or equivalent cat part of make specified in list make as approved by GE.

Stainless steel Soap dish, any type, fixed with plugs chromium plated brass screws fixed in repairs complete all as specified and as directed. Cat part No-AQN-7733 of Jaquar or its equivalent cat part of make specified in list make, as approved by GE.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 45cm long fixed in repairs, complete all as specified.

Health faucet with one mtr long flexible tube and wall hook chromium plated screwed down for iron pipe fixed in repairs, complete all as specified and as directed.

Plastic water closet seat cover white closed pattern with flat bottom and cover including chromium plated hinges device fixed in repairs, complete all as specified and as directed.

PVC (SWR) 75 mm dia floor trap plain with grating including jointing with solvent cement fixed in repairs, all as specified and directed

Taking down eaves gutters and rain water pipe , soil and waste pipe (any size or pattern), includding all fittings, heads , shoes bends , swan-necks etc . complete all as specified.

110mm bore PVC SWR Type-B pipes (pressure not less than 6 kg /cm2) single socket in any length with rubber joints laid in floors/trenches etc all as specified and directed.

110mm bore PVC SWR Type A pipes ( pressure not less than 4 kg /cm2) single socket in vertcal length for rain water with rubber joints fixed to walls with PVC//MS holder clamps complete all as specified and directed.

75mm bore PVC SWR Type-B (pressure not less than 6 Kg/cm2) pipes single socket in any length with rubber ring joints laid in trenches or in floors etc all as specified and directed.

PVC SWR vent cowl 110 mm complete all as specified and as directed.

PVC (SWR) bend 110 mm dia any radius all as specified and directed

PVC SWR bends any radius 110 mm bore with oval access door, complete all as specified and as directed.

110mm PVC (SWR) junction single, (single T) equal or unequal provided with access door, complete all as specified and directed.

PVC SWR bends any radius 75mm bore complete all as specified.

PVC SWR bends any radius 75mm bore with oval access door complete all as specified.

75mm PVC (SWR) junction single, (single T) equal or unequal provided with access door, complete all as specified and directed.

Demolition of Cement Concrete (reinforced) of any description and in any position not otherwise specifically provided for including removing the rubbish off the premishes all as specified and as directed.

Reinforced cement concrete 1:2:4, B-1 (Using 20mm graded stone agg) as in manhole covers slab/shelves etc including necessary form work for fair finished surfaces complete all as specified and directed.

TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia complete all as specified.

Taking down old unsv roof treatment including PCC padding if any, plastering, removing existing bitumen felt treatment including brushing, cleaning top surface of roof slab, brooming etc complete all as specified and as directed.

Rendering 15 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces including finishing the surface fair and even on roof slab complete all as specified and as directed.

Roof treatment :- Water proofing treatment to RCC roof slab including parapet as under :- (a) Ist Course : Apply a coat of bituminous primer conforming to IS-3384@ 0.40 Kg /Sqm on prepared surface of plaster and after drying of primer, apply a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.2 Kg/sqm on plastered surfaces. (b) 2nd Course : APP (Atactic Polypropylene) modified polymeric membrane, 5 layered, 3 mm thick weight not less than 3.0 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 150 mm end overlap, membrane has to be laid with LPG torch and overlap sealed and finished neat, all joints. (c) 3rd Course : Apply a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.2 Kg/sqm over membrane and dusted with dry sand @ 0.50 to 1 Kg/sqm. (i) On Non-accesible roof : After providing (a) to (c) provide aluminium paint as per manufacturer instructions. (ii) Coved fillet in PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) of required radius 75mm shall be provided at the junction of roof and vertical surface such as parapet wall/mumty around opening and treatment mentioned above shall be applied followed by a cement plaster 20mm thick in cement mortar(1:6). Note : (i) Roof treatment work shall be carried out through approved manufacturers only or through their authorised personal only.

40mm thick brick tiles laid on 15mm thick cement mortar and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on mud phuska complete all as specified and directed.

Soakage well of size 1.8 M dia X 3.00M deep including excavation in any type of soil, foundation in pcc 1:3:6, well of honey combed built in brick work in CM 1:4. and RCC cover M-25 concrete, filling with brick bats, complete all as specified & shown on Drg No CE/TD-1202/03 sheet 1/2 & 2/2.

Taking down carefully copper/aluminium point wiring (light,fan,bell, socket or power) complete,including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty and white cement at necessary holes for smooth finishing complete all as specified and directed complete all as specified and directed.

Material and labour for point wiring complete with 1.5 sqmm PVC insulated, FRLS type, ISI marked,conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through and including PVC Conduit 20 mm dia medium grade and including cutting, chasing work at any height and all accessories are concealed in walls / roofs / floors / ceiling etc. metal flush box with top,bottom,side/back wall knockout for conduit entry from any direction made out of 1.60mm thick suitable for fixing of modular top cover plate as per numbers of switch modules for modular switches,sockets,fan regulators,red colour indicator, blank plates etc as approved coloures and including 1.5 Sqmm PVC insulated multistranded FRLS type unsheathed(Green colour),single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat including providing putty and white cement for smooth finishing of existing surface complete all as specified and directed for the following:- (Note:- All necessary accessories such as modular steel box,top cover plate, blank plate, screws,washers to be used of same make/brand only and shall be deemed in to included in quoted rate only.)

All as per item No-96 above but for One light point/fan /bell point controlled by one switch.

All as per item No-96 here-in-before but for One 5 pin 6 amps socket point controlled by one 6 amps switch on independent board .

All as per item No-96 here-in-before but for One 5 pin 6 amps socket point controlled by one 6 amps switch on same board .

Material and labour for point wiring complete with 2.5 sqmm PVC insulated, FRLS type, ISI marked,conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through and including PVC Conduit 20 mm dia medium grade and including cutting, chasing work at any height and all accessories are concealed in walls / roofs / floors / ceiling etc. metal flush box with top,bottom,side/back wall knockout for conduit entry from any direction made out of 1.60mm thick suitable for fixing of modular top cover plate as per numbers of switch modules for modular switches,sockets,fan regulators,red colour indicator, blank plates etc as approved coloures and including 2.5 Sqmm PVC insulated multistranded FRLS type unsheathed(Green colour),single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat including providing putty and white cement for smooth finishing of existing surface complete all as specified and directed for One 15 amps power socket outlet point controlled by one 16 amps switch on independent board. (Note:- All necessary accessories such as modular steel box,top cover plate, blank plate, screws,washers are to be used of same make/brand only and shall be deemed in to included in quoted rate only.)

Modular type switch 6 Amps, single pole, 1way,1 module, 240V, ISI Marked Complete all as specified and directed.

Modular type switch 16 Amps, single pole, 1way,1 module, 240V, ISI Marked Complete all as specified and directed.

Modular type socket shuttered type 6 Amps, 2/3 Pin combined 2 module, 240V, AC ISI Marked Complete all as specified and directed.

Modular type socket 6 A/16 Amps, 2/3 Pin combined shuttered socket 2 module with light indication ,240V,AC ISI Marked Complete all as specified and directed .

Fan regulator modular type electronic compatible with BLDC fan, stepped type 100 Watts, 2 module 240Volts, AC ISI marked complete all as specified and directed.

Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed by GE.

LED bulb 12 watts, 240Volts, 50Hz pin type and including removing old unserviceable item complete all as specified and directed. Cat Part No-BL0212WB22 OF BENLO or equivalent of Bajaj, Havells as approved.

LED light fitting 1x9W bulk head luminaries IP 65 complete with all accessories including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V 50 Hz, Complete all as specified. Cat part No LW07-141-XXX-57 G1 Make Wipro or equivalent in Phillips, Crompton, Havells, bajaj as approved.

Ceiling rose, 3 terminal ,PVC/polycarbonate body ISI marked, complete all as specified and directed.

LED light fitting 1x20W, 220V, AC general purpose surface and wall mounted LED batten with driver, Holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Ceiling fans complete with blades, down rods, and accessories, 230 volt, 1200mm sweep, min air delievery 210 CFM with service value 6 BEE five star rated with brushless direct current motor (BLDC) complete all as specified and directed. Make:- Cat Part No Zinger of Make Havells or its Equivalent cat part of make as specified in list of make here- in after.

Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 8 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging, blanking plates where required testing and commissioning in replacement, complete all as specified. Make:- Havells cat part No-DHDPSHODPW08 or its Equivalent cat part of make of Legrand / ABB / L&T as approved by GE.

MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series fixed complete all as specified and as directed. Make:-Havells cat part No-DHMGCSPF006-032 or its equivalent cat part of make-Legrand / ABB / L&T as approved by GE

MCB's single pole & neutral 240 volts 40 to 63Amps 10 KA 'C' series, complete all as specified and as directed. Make: Havells Cat Part No.DHMGCSNF040-063 or its equivalent cat part of make-Legrand / ABB / L&T as approved by GE

Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 4 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging, blanking plates where required testing and commissioning in replacement, complete all as specified. Make:- Havells cat part No-DHDPSHODPW04 or its Equivalent cat part of make of Legrand / ABB / L&T as approved by GE.

Supply laying & testing of XLPE insulated, armoured, heavy duty electric under ground cable with stranded aluminium conductor, 1100 volts grade of size 16 Sqmm nominal cross section x 2 core, laid in trenches, sleeving through pipes or fixed on poles & walls or laid under floors including jointing with suitable size aluminium lugs complete all as specified.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out etc in any type of soil, complete all as specified and directed.

Returning filling in including spreading watering and well ramming in layers not exc 25 cm complete all as specifed.

Removing surplus soil to distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Sand cushioning to under ground cable, 8 cms thick before laying the cable and 15 cms thick after laying and stretching the cable in trenches including hand punning and consolidating, punned to 18cm thickness, complete all as specified and directed. Note : For payment purpose, only punned thickness shall be measured.

Supply and laying sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed.

Supply and fixing electric water heater, storage type steel body with stainless steel inner tank and with heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece incl making holes on walls for proper fixing with nuts and bolts complete making the surface good as per existing all as specified and directed. Note: Old unsv geyser shall be deposited in MES yard. Make : Havells(Fabia) of Cat Part No GHWAFATIB025 or equivalent cat part of make as specified in list of make here-in-after.

S&F Exhaust fan Metal (Steel) body AC single phase 230V 50 Hz of size 300mm sweep including necessary nut, bolts / screws including taking down existing one writing MES No with synthetic enamel paint all specified and directed. Make-Havells Cat No Ventil DX-WH/BLK or equivalent in bajaj, Crompton Greaves etc. Note:- Old Unserviceable Exhaust fan shall be deposited to MES store yard.

Earthing complete with galvanised steel earth plate electrode 600mmx600mmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground) with top edge of plate not less than 1.5m below normal ground level connecting to the Galvanized iron earth wire 4mm dia by means of bolts, nuts check nuts and washers of galvanised iron and GI Strip 32x6mm protected by provision of GI Light grade pipe of 40mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 40mm grade crushed stone aggregrate iwh 40mm thick cover of RCC (1:2:4) raniforced with PM (weight not less than 4Kg/sqmm) and frame of angle iron 25x25x6mm with lugs 02 Nos and 6mm dia MS bars handle made to shape, GI Light grade 20mm bore pipe for watering perforated at bottom 1.75m long placed on top edge for earth platem common salt and charcoal filling, test point made out of 75x50x6mm phodphorous bronze with fixing arrangement, funnel, wire mesh and earth work in hand/ dense soil filling in andremoval of surplus soil to a distance not exceeding 50m all as per electrical plate No-03 of SSR 1991 Pt-I and connecting to earh test point incl testing on completion, complete all as specified.

GI pipe light grade 40mm bore for cable protection fixed on pole or liad in trenches under floor,ducts etc with fixing clamps, nuts, bolts etc., complete all as specified.

Plain Cement Concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete all as specified and directed.

Concrete bed to drain pipes 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) including packing under and haunching against the side of pipes after they are laid and tested for 150mm internal dia of pipe, complete all as specified and directed.

Reinforced concrete pipes 150mm dia, class NP3, laid and jointed with collars, complete all as specified and directed.

LLDPE conventional type septic tank designed to carry sewage and sludge water for 10 users incliding excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft, connection etc., complete all as specified and as directed. Make-Sintex, Rajshree, Polycon and Star

LLDPE conventional type septic tank designed to carry sewage and sludge water for 20 users incliding excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft, connection etc., complete all as specified and as directed. Make-Sintex, Rajshree, Polycon and Star

LLDPE conventional type septic tank designed to carry sewage and sludge water for 30-35 users incliding excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft, connection etc., complete all as specified and as directed. Make-Sintex, Rajshree, Polycon and Star

Soakage well of size 2.4 M dia X 4.50M deep including excavation in any type of soil, foundation in pcc 1:3:6, well of honey combed built in brick work in CM 1:4. and RCC cover M-25 concrete, filling with brick bats, complete all as specified & shown on Drg No CE/TD-1202/03 sheet 1/2 & 2/2.

Soakage well of size 1.2 M dia X 3.00M deep including excavation in any type of soil, foundation in pcc 1:3:6, well of honey combed built in brick work in CM 1:4. and RCC cover M-25 concrete, filling with brick bats, complete all as specified & shown on Drg No CE/TD-1202/03 sheet 1/2 & 2/2.

S&F in repair GI water tubing in replacement 25mm bore 'medium grade', galvanized, with all fittings like socket, union, elbow, bend, tees etc jointed and laid in trenches complete all as specified and as directed.

S&F in repair GI water tubing in replacement 20mm bore 'medium grade', galvanized, with all fittings like socket, union, elbow, bend, tees etc jointed and laid in trenches complete all as specified and as directed.

Cutting & screwing of pipe line of 50mm dia for branch connection alongwith insertion of suitable elbow/union/nipple 50mm dia and connecting material such as joints, nuts, bolts etc complete all as specified and as directed.

25 mm bore Gun-metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed high pressure with crutch or butterfly handle fixed in repairs complete all as specified and as directed.

Construction of brick masonary valve pit of size 1000mmx1000mmx 1000mm (Internal dimension of chamber) with follwing specifications:- Pit shall be underground with foundation in PCC (1:3:6) type-C2 brick work in CM (1:6), internally finished with 15mm thick cement plaster in CM 1:4 and externally flushed pointed as work proceeds. Flooring shall be 40mm thick PCC (1:2:4) type B-1 laid over 75mm thick hardcore. Cover shall be of 6mm thick MS black sheet fixed to angle iron frame made out of 25x25x6mm by friction hinges welded to frame and sheet. Angle iron frame will be grouted on masonry chamber with MS hold fasts. Locking device will be provided to lock MS sheet cover to angle iron frame. One handle made out of MS round bar 12mm dia D type 15cm long shall also be welded on MS sheet cover. The steel surfaces exposed to view shall be painted with two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and directed.

Construction of a toilet and bathroom with RCC framed structure specification complete all as specified and shown in the main drawings and TD drawings referred in main drawings.

Surface excavation n exc 30cm deep and averaging 15 cm deep & getting out in any type of soil all as specified and directed.

100 mm thick cement concrete type D-2, 1:4:8 (40mm graded crushed stone aggregate) as in sub base of floors finished even & fair, complete all as specified and directed.

Chequered cement concrete tiles 300x300x 25mm thick, set & jointed in neat cement slurry and pointed with equal proportion of white and grey cement mixed with pigments, laid over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed.

Precast cement concrete (1:2:4) using 20mm graded crushed stone aggregate as in landings, cover slab (for manholes etc), chullah hoods, chajjas, water troughs, shelves and similar articles with plain fair faces including chamfers, weatherings, throating etc. and setting in cement mortar (1:4) including necessary form work complete all as specified and directed.

Supply and fixing LED light fitting mirror type with 2 feet, 10 watt, 220V, AC for general purpose surface and wall mounted LED batten with driver including connecting up with three core flexible copper conductor cable of suitable size complete incl testing after fixing all as specified and directed.

S&F Exhaust fan single phase PVC/Sturdy engineering plastic body 230V 50 Hz of size 250mm sweep ISI marked with louvers shutter complete with all accessories including connecting up from ceiling rose complete all as specified and directed. Note: Old unsv exhaust fan shall be deposited in MES yard. Make:- Cat part No refresh air SPS of Havells or its Equivalent cat part of make as specified in list of make here- in after.

Electric water heater storage type, capacity 50 litres and heating element 2KW, BEE 5 Star rated complete with all accessories such as a safety valve, thermostate, NRV, connection pipes of GI/PVC and necessary electric connections etc including taking down existing and depositing in MES. Make : Crompton/Havells/Bajaj as approved.

Earthing complete with galvanised steel earth plate electrode 600mmX 600mmX 6mm thick buried directly in ground vertically ( earth pit not less than 2.25 meters deep below ground level) with top edge of plate not less than 1.5 metres below ground level, connected to and including galvanised iron wire 4 mm dia and light grade protection pipe of 15 mm dia from earth electrode up to test point or up to 7.5mtr whichever is less by means of GI bolts, nuts, check nuts and washers all as per electrical plate No 3 of SSR Pt-I and GI watering pipe of 20 mm dia medium grade,GI funnel with wire mesh,including charcoal, salt packed all around the earth electrode plate in layers, PCC earth pit chamber 1:3:6 type C1, of size 45X 45X 45 CM,RCC cover 1:2:4 type B1 of size 45X45X6 CM with Reinforcement bars of 8mm dia @120mm c/c excavation/earth work in any strata and returning filling, removal of surplus soil and testing/test point for required value including removing old item complete all as specified and directed.

Supply, laying, jointing and testing XLPE cable insulated, armoured, earthed, heavy duty electric cable with aluminium conductor, 1100 Volt grade, cross sectional area 10 sqmm 2 core including necessary cable lugs, glands, insulation tape etc complete all as specified and as directed.

Supply only Integral water proofing compound.

Mild steel TMT bars 6-8mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia complete all as specified

Concrete bed to drain pipes in PCC 1:3:6 type C-2 (Using 40mm graded crushed stone aggregate) including packing under and haunching against the side of pipes after they are laid and tested for 150mm internal dia of pipe, complete all as specified and directed.

M&L for Construction of Soakage well in any type of soil, foundation in PCC 1:3:6,wall of honeycombed brick work in CM 1:4, RCC cover slab in M-25/RR masonary/filling with brick bats (size 2.4 M dia X 3.00M deep) Drg No CE/TD-1202/03 sheet 1/2 & 2/2.

NATIONAL TRADING COMPANY (BID ID -3263320)

KANWAL KUMAR GUPTA (BID ID -3258493)