PROVN OF CERTAIN SANCTIONED WORK AND SPL REPAIR AT BARAMULLA UNDER GE 969 EWS

Amount

Excavation over areas n.exc 1.50m deep and getting hard/dense soil complete all as specified and directed.

Excavation in trenches n exc 1.5 M wide and n exc 1.5 M deep for foundation, etc or for shafts, wells, manholes etc n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in hard/dense soil complete all as specified and as directed.

M&L Plain Cement concrete Type D-2, 1:4:8 (40mm graded aggregate), in foundation, filling and mass concrete, complete all as specified and as directed.

M&L Plain Cement concrete Type C-2, 1:3:6 (40mm graded aggregate), in foundation, filling and mass concrete, complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing unserviceable outside complete all as specified and as directed.

Demolition of brick/stone masonry built in cement mortar incl all quoins, arches, pillars etc but excluding ashlar facings, dressed stonework and precast concrete articles.

M&L for precast cement concrete block type C-1, 1:3:6 (20mm graded aggregate) with solid blocks, exc 10cm in width and setting in cement mortar (1:4) complete all as specified and as directed.

M&L Walling of Random rubble masonary, uncoused, well bonded, bedded and solidly hearted, built in cement mortar (1:4) complete all as specified and as directed.

M&L pre cast cement concrete (1:2:4), type B-1 (using 20mm graded crushed stone aggregate) set in cement mortar (1:6) in bond stons for stone masonry and the like including necessary formwork.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface n.exc 40mm to face stones and dressing of face beds and joints,as specified,of random rubble walling,uncoursed or brought upto courses for Granite or Trap Stone.

M&L raised pointing in cement mortar 1:4 to random rubble masonry, uncoursed or brought upto courses all as specified and directed.

M&L PCC 1:2:4, type B-1 (using 20mm graded aggregate) as in surface channel or drains including necessary formwork.

M&L for extra for forming fair finished drain channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.

M&L Plain cement concrete type B-1 1:2:4 (using 12.50mm graded aggregate) as in copings complete all as specified and as directed.

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc

M&L for rendering 15mm thick in CM 1:4 on brick or concrete surfaces and finished surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in CM 1:3 on concrete surfaces (over roof slab) and finished surfaces even and smooth without using extra cement using water proofing compound @ 3% by wieght of cement complete as specified and directed. (Note : Water proofing compound shall be measured and paid separately).

Supply only integral water proofing compound.

M&L for rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces and finished surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of newly plastered surfaces including applying two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer , of required shade and colour over a coat of primer complete, as per manufacturer's specification complete all as specified and as directed.

M&L for preparation of surfaces of any description (wall, ceiling, boards etc) wood, steel, iron, concrete, brick, stone etc exc 10cm in width or girth and including applying two coat of fire resisting paint complete all as specified and as directed.

M&L 75mm thick plain Cement concrete Type C-2, 1:3:6 (using 40mm graded aggregate) as in sub base and plinth protection complete all as specified and directed.

M&L 75mm thick plain Cement concrete Type B-2, 1:2:4 (using 40mm graded aggregate) as in floor finished even and smooth without using extra cement complete all as specified and as directed.

M&L 100mm thick plain Cement concrete Type B-2, 1:2:4 (using 40mm graded aggregate) as in floor finished even and smooth without using extra cement including spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified and as directed.

S&F mild steel work quality as framed work in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and incl either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete all as specified and as directed.

S&F non asbestos fibre cement building boards 8mm thick fixed in framework with screws complete all as specified and as directed.

M&L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for reinforced concrete pipe class NP-2 laid and jointed complete with collars of 450mm dia, complete all as specified and as directed.

Returning filling in incl spreading leveling, watering and well ramming in layers n exc 25 cm complete all as specified and as directed.

Removing of excavated soil not exceeding 50m and depositing where directed at a level not exc 1.5 M above the starting point, complete all as specified and as directed.

M&L for complete removal of existing treatment on wall surfaces and prepration of new or previously untreated surfaces and applying two coat of exterior emulsion Apex weather proof. complete all as specified and as directed.

M&L for complete removal of existing treatment of surfaces (wall, ceiling, doors, windows etc) of any description wood, steel, iron, concrete, brick, stone etc exc 10cm in width or girth and preparation and applying two coats of fire resisting paint complete all as specified and as directed.

M&L TMT bars 10mm dia and over cut to length, bend to shape required including cranking, bending spirally for hookings for cols, hooking ends and binding with and including mild steel wire (aneeled) not less than 0.9mm dia, complete all as specified and as directed.

All as per item No 33 but but 5mm dia and over upto and incl 10mm dia in stirrups, spacers and binders complete all as specified and as directed.

M&L for formwork to sides of concrete to sides of pillars, posts, struts, piers, columns and stanchions, flat, fair finished surface of concrete complete all as specified and directed.

M&L for reninforced cement concrete (nominal mix) type B-1, 1:2:4 (20mm graded aggregate) Columns, pillars, piers, posts and struts complete all as specified and as directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc, flat, fair finished surface of concrete complete all as specified and as directed.

M&L for reninforced cement concrete (nominal mix) type B-1, 1:2:4 (20mm graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for 38mm thick aluminium dividing strips, 1.5mm thick, inserted in position, conform to design complete all as specified and as directed.

M&L for EPDM membrane waterproofing treatment with membrane not less than 1.52mm on the roof and vertical wall surfaces with minimum roll width 6mx 15m after properly removing the existing treatment and preparing the surfaces by clearing and removing any sharp mtrls like reinforcement steel, loose foreign materials, oil grease etc and ensuring a smooth surface. Membrane shall be full adhered with high strength solvent based having quick bonding between the membrane with the help of bonding adhesive as per manufacturer standard instructions (suitable for temp and environment condition of the site) complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting , any gauge and thickness in roof covering including Nainital or similar pattern roof covering complete all as specified and as directed.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Dismantling wall and ceilling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/ blankets, any thickness, cover fillets etc complete all as specified and as directed.

M&L 4 mm thick veneered decoretive, Plywood grade 1 (BWR resin) with decoretive face veneers on one faces , fixed with nails to timber frame work on ceiling complete all as specified and as directed.

M&L 4 mm thick veneered decoretive, Plywood grade 1 (BWR resin) with decoretive face veneers on one faces , fixed with nails to timber frame work on wall, complete all as specified and as directed.

Dismantling of timber scantling 40 Sqcm and over in section in any position in unframed work complete all as specified and as directed.

M&L for second class soft wood (Kail) clean swan timber fixed in scantling complete all as specified and as directed.

Dismantiling of timber fillets rails, posts rafter purlins etc under 40 Sqcm in section in any position in framed work complete all as specified and as directed.

S&F second class hardwood plain fillets square, rectangular in section exc 13 Sqcm & not exc 25 Sqcm complete all as specified and as directed.

S&F second class hardwood plain fillets square, rectangular in section exc 6 Sqcm and not exc 13 Sqcm complete all as specified and as directed.

Dismantling of boarding any description fixed in any position with nails complete all as specified and as directed.

M&L, for weather boarding of 2nd class softwood, clean sawn, plain, 20 mm thick or feather edged 15 mm to 20 mm thick and fixed with 30 mm laps complete all as specified and as directed.

S&F facia boarding of 2nd class soft wood planed one side with but joints 20mm thick and champhered one side and the boarding is matched complete all as specified and as directed.

M&L for 25mm thick PCC 1:2:4 type B-O (using 12.5 graded aggregate) as in floors finished even and fair complete all as specified and as directed.

S&F coloured non skid ceramic tiles 300x300x7 thick , in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and Incl screed bed 15 mm thick in CM (1:6) complete all as specified and as directed.

Taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 sqm each and removal from site complete all as specified and as directed.

Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm each with shutters (W/out taking off shutters from the frames) complete all as specified and as directed.

S&F 2nd Class Soft wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and as directed.

S&F 2nd class soft wood 35mm thick factory made panelled shutters with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS-1003 (Pt-I) kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 2nd class 30 mm thick soft wood (Kail) glazed skeleton shutters open rebated and prepared to receive guage etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc and fitted to chowkats size of members of shutters as specified in SSR Part - I section 8 Clause 8.23 (b) for windows, ventilators etc are provided with stiles and rails, complete all as specified and as directed.

S&F Mild steel MS Cold rolled Butt hinges medium weight 100 mm long complete all as specified and as directed.

S&F Mild steel MS Cold rolled Butt hinges medium weight 75 mm long complete all as specified, complete all as specified and as directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy complete all as specified and as directed.

S&F 300 mm size mild steel ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F 200mm long Anodised Aluminium tower bolt complete all as specified and as directed.

S&F 100mm long Anodised Aluminium tower bolt complete all as specified and as directed.

S&F 150mm long extruded aluminium alloy handle complete all as specified and as directed.

S&F 100mm long extruded aluminium alloy handle complete all as specified and as directed.

S&F Sheet glass ordinary quality & glazing with oil putty in square n-exc. 0.5 sqm in each pane 3mm thick complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer including preparation of new wooden or wood based surfaces over 10cm width or girth etc all as specified and as directed.

S&F in repairs curtain rails , anodised aluminium alloy with fixing brackets , stops, rollers etc. complete all as specified and as directed.

S&F for Aluminium anodised Brackets fixed in repair complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint, white or tinted, complete all as specified and as directed.

All as per item No. 74 above but one coat of oil bound distemper on walls complete all as specified and as directed.

Supply only fine sand at site including royalty and carriage for preapring compost at site (same shall be brought at site and stacked for measurement before incorporating before incorporation in the work.)

Supply only good earth at site including royalty and carriage for preparing compost for pits/required for planting trees fine sand at site including royalty and carriage for preparing compost at site (same shall be brought at site and stacked for measurement before incorporating in the work 20% of Computed volume shall be reduced for loose stacking.

Supply only manure at site including royality and carriage for preparing compost at site (manure shall be brought at site and stacked for measurement before incorporating in the work 8% computed shall be reduced for loose stacking.

Preparing compost pits of size (0.60x0.60x0.60)M by excavation in ordinary soil, applying antitermite treatment, planting trees & refilling of the pit with compost (manure sand & sweet earth mixed in ratio (1:1:4) breaking colds, ramming and flooding with water filling with more compost if necessary and fine dressing including removal of rubbish unserviceable materials & surplus soil to a distance nexc 100 mtr, ATT shall be in form of 200 grams neem cake mixed 2 ML per litre in the first watering of 20 litre per pit. Note: 1. The rate for excavation and getting out of soil shall be deepmed to be included in the unit rate of this item. 2. The rate for mixing earth, manure and sand, deemed to be included.

Preparing compost pits of size (0.90x0.90x0.90)M by excavation in ordinary soil, applying antitermite treatment, planting trees & refilling of the pit with compost (manure sand & sweet earth mixed in ratio (1:1:4) breaking colds, ramming and flooding with water filling with more compost if necessary and fine dressing including removal of rubbish unserviceable materials & surplus soil to a distance nexc 100 mtr, ATT shall be in form of 200 grams neem cake mixed 2 ML per litre in the first watering of 20 litre per pit. Note: 1. The rate for excavation and getting out of soil shall be deepmed to be included in the unit rate of this. 2. The rate for mixing earth, manure and sand, deemed to be included.

Supply and planting followed trees in location shown by Engr-in-charge/GE, girth 80mm to 100mm minimum (measured at 150mm top of roots) and height as shown

PUMERIA ALBA 6' HEIGHT

ROYSTONEA REGIA 6" HEIGHT

SHOREA ROBUSTA 4' HEIGHT

BAMBUSA VALGARISA 6' HEIGHT

BOTTLE PALM 4' HEIGHT

ASHOKA PENDULA 4' TO 6' HEIGHT

Supply and planning shrubs i.e. Aclypha 2, calliandraz, crotons 3, hamcxha, jasminum, cpensis, hibisew, ticoma complete all as specified and as directed.

M&L for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; including 75mm thick cement concrete Type C-2 !3:6 (using 40mm graded aggregate) as sub base Complete all as specified and directed.

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM (1:4) complete all as specified and as directed.

M & L for rendering 15 mm thick plastering on brick work or concrete surface in CM (1:6) and rendering is to be finished even and smooth w/o using extra cement .complete all as specified and directed.

S&F for keys pointing to squared rubble, coursed or uncoursed stone masonry in cement mortar (1:4) complete all as specified and as directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Dismantling structural steel work incl doors, gates but excl framed truss etc. complete all as specified and as directed.

Taking up or down steel tubling 15mmGI pipe and connection, including cleaning for refixing or removal complete all as specified and as directed.

Dismantling Old bib tap/angle valve

Dismantling Old flushing cistern

Dismantling Old PVC water tank exc 500 but n. exc 1000 ltr capacity

S&F 1 HP High Flow Motor/ MS Series Product Code No MHPAMF0X50 Model Hi-Flow MS 1 HSN code 8413 all fittings including complete all as specified and as directed.

S&F Round Conduit PVC Pipes (Socketed) HSN Code 39172310 MMS, Product Code PRCS 20 M ( Medium mechanical stree) and all fittings accessories complete all as specified and as directed.

S&F Gl tubing, medium grade, ISI marked complete with all fittings, laid in trenches or laid under floors, fixed on walls with and providing clamps etc complete all as specified and as directed for 25mm bore.

S&F Flexible copper cable 1.5 Sqmm 3 Core FRLS PVC complete all as specified and as directed.

S&F Copper Conductor 2.5 Sqmm multistranded FRLSH complete all as specified and as directed.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 Sqmm 2 core.

S&F Aurom Spotlight 13W Ordering code LHEBAIP1IZIW013 HSN Code 9405 complete all as specified and as directed.

S&F in repairs MCB, DP 40 Amps 240 Volts B curve, complete all as specified and as directed.

S&F in repairs Distribution board, SPN 4 Way, Double door complete all as specified and as directed.

S&F MCB Single pole 6-32A Amps 240 Volts B curve complete all as specified and as directed.

Taking down copper/aluminium Point wiring (light, fan, socket or power) complete including fixture and fittings such as Switches, Ceiling roses, pendants, regulators, sockets, light fitting etc. complete all as specified and as directed.

Taking down service cable 10 Sqmm 2 Core, all as specified and as directed.

Taking down DB 2 Way along fixtures, complete all as specified and as directed.

Note:- Schedule of credit Rs 2,21,688.00 will be deducted from total amount quoted while accepting the bid. Details of schedule of credit is given in tender documents.

M/S BILAL CONSTRUCTION AND CO

ANUSHA ENTERPRISES

M/S KULWANT SINGH RAINA AND CO

M/S SUMJI BROTHERS

HAYAT TRADING CORPORATION

MS QADRI BUILDERS

ALI MOHD NAJAR