Construction of New Hotel Building in the campus of Hotel Ratan Bihar in Dhanbad District

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Extra for earth work in hard soil as per specification and direction of E/I. (vide classification of soil item - B).

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Ordinary rock

Hard rock (blasting prohibited)

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50Mand lift of 1.5M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75 A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing designation 75A one Brick Flat Soling joints with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I.

Supplying chemical emulsion in sealed containers including delivery as specified (chlorpyriphos/ lindane emulsifiable concentrate of 20%)

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground leveland removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level

1:1.5:3 (1 cement: 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size)

1:3:6 (1 Cement: 3 coarse sand(Zone III): 6 graded stone aggregate 20 mm nominal size)

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse send : 6 graded stone aggregate 20 mm nominal size ) over 75 mm thick bed of dry brick ballast 40 mm nominal size ,wall rammed and consolidated and grouted with fine sand including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement- All work up to plinth level. 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in wall (any thickness), including attached pilasters, butterses, plinth and string courses, fillets, column, pillars, piers, abutments, posts and struts ets. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floor, roofs having slope up to 15'' landing, balconies, shelver, chajjas , lintels, bands, plan window sills, staircases and spiral stair case above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately).

All works upto plinth level

All works above plinth level upto floor V level

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs,(excluding landings) except spiral-staircasess.

Weather shade,Chajjas, corbels etc. including edges

Suspended floors, roofs, landings, balconies and access platform with water proofply 12 mm thick.

Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick

Providing tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. Taking 8mm TMT FE 500 ( only valid for SAIL & TATA STEEL)

Providing Tor steel reinforcement of 10mm, 12mm & 16mm mm dia. bars as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l.

10mm TMT FE 500 (only valid for SAIL & TATA Steel)

12mm TMT FE 500 (only valid for SAIL & TATA Steel)

16mm TMT FE 500 (only valid for SAIL & TATA Steel)

20mm TMT FE 500 (only valid for SAIL & TATA Steel)

25mm TMT FE 500 (only valid for SAIL & TATA Steel)

Making 6x6mm grooves in plaster surface over walls truely horizontal or vertical as specified. at regular intervals, at all heights including cleaning, finishing, scaffoding and curing wth all leads and lifts of water all complete as per building specification and direction of E/|

Providing designation 75 A brick work in C.M.(1 :6) in foundation & Plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints cost of screening materials, scaffolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75b work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.m. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials ranking out joints to 15mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 75A brick work in CM (1:6) in superstructure with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 125mm thick reinforced designation 75A brickwork in C.M. (1:4) in Superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, cost of materials, racking out joints to 15mm depth, carriage, taxes and royalty (but excluding the cost of reinforcement) all complete as sper building specification and direction of E/I.

Providing designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:6) in superstructure with approved quality of clean sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 112mm thick reinforced designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carraige of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforced) all complete as per building specification direction of E/I.

Extra for brick work for EACH consecutive floor above first floor including watering and scafolding, all complete as per direction of E/l.

2nd Floor

Terrace floor

Supplying frtting and fixrng good quality, well dressed and well seasoned sal wood worl< in chaukhat in doors, windows skylights, fanlights and C/W celetialwindows openings, including wedge over :rll clamps complete including application of two coats of wood preservative of approved qirality on the surface butting walls and lintels all complete as per building specification and direction of E/I.

Supplying, fitting, and fixing good quality, well dressed and well seasoned Teak wood work in choukhat in door, window, skylight, fanlight, and C/W celestrial window openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per buidling specification and direction of E/I

Supplying,fitting & fixing 250x20x6mm L-type M.S. Clamp properly fishtailed,including making holes and setting the same in 250x125x75mm cement concrete block (1:2:4) with cost of all labour and materials and taxes as per building specification and direction of E/I.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)

Second class teak wood (35 mm thick shutters)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door & windows with black board core blended with high quality phenol phormal dehydes synthetic resin both side comercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l

Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (bathroom and W.C. doors) using synthetic rubber based adhesive.

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured) : Rectangular or square

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood (50x12 mm)

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door / window / Ceosetory windows & other Frames / Chowkhat comprising of virgin Pvc polymer of K | value 58 - 60 (Suspension Grade), calcium carbonate and natural | fibers (wood powder / rice husk / wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying Pvc solvent cement and screwed - with - full - body - threaded - starheaded ss screws having minimum frame density of750 kg / cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N / mm, modulus of elasticity 900 N / mm and resistance to spread of flame of Class A category with property of being termite / borer proof, water / moisture proof and fire retardant and fixed in position with M. Shold fast / lugs / Ssdash fasteners of requireddia and length complete as per direction of Engineer - In - Charge. (M, S | hold fast / lugs or ss dash fasteners shall be paid for separately) Note: For WPC solid door / window frames, minus 5mm tolerance in dimensions i. e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made. Frame size Frame Size 45x85 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 30 mm thick

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium sliding door bolts, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour and shade, with necessary screws etc. complete.

Twin rubber stopper

Providing and fixing chromium plated brass night latch of approved quality including necessary screws etc. complete.

Providing and fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete-

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.

Providing and fixing Lock Sets of HL Series 8" On Plate (Size 200mm) With Knob and Key of 60 mm etc all complete. (make- Dorset or Equivalent, model no. - HL KAI X)

Providing and fixing SD16PGM Pull Handles (16 inch hight) & make with necessary screws etc all complete.

Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm).

Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm.)

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.

Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required die and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paid for separately).

Providing and fixing glazing in fire resistant door shutters, fixed panels, ventilators and partitions etc., with G.I. beading of appropriate size, made out of 20 SWG G.I.sheet (zinc coating not less than 120 gm/m2), fire resistant sealant, including applying a coat of approved fire resistant primer on G.I. beading etc., complete all as per direction of Engineer-in-charge.

With clear fire resistant glass panes 6mm thick of approved brand, having minimum 60 minutes fire resistance

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Supplying, fitting, and fixing M.S. grill made of 20 x 6mm M.S. flat as per approved design and drawing , properly fabricated with joints continuous fillet welded and finished, carriage of grill to work site, hoisting as per building speficiation and direction of E/I. (where material is not supplied by the deppt.)

Supplying,fitting and fixing M.S. grill gate with M.S. grills made of 20xGmm M S. flats or 16mm. M.S. square bars fitted on25x25x 6mm. M.S. Angle frame -do- (when steel is not supplied by the deptt.).

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built-up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required

In gratings, frames, guard bar, ladders, balcony and staircase railings, brackets, gates and similar works

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing 18 mm thick gang saw cut mirror polished, machine cut for kitchen platforms, vanity counters facias and fimilar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand ) with joints treated with white cement , mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade Area of slab over 0.50 sqm

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

25 mm thick

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Glazed vitrified floor tiles polished finish of size

Size of Tile 600 x 600 mm

Size of Tile 600 x 1200 mm

Size of Tile 800 x 800 mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.

Size of Tile 600x600 mm

Size of Tile 800x800 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

Size of Tile 800x800 mm

Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge:

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant atOMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M- 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing 12mm thick cement plaster (1:3) with clean coarse sand of F.M. 1.5 and including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I

Providing 12mm Thick cement plaster (1:6) with clean coarse sand F.M. 1.5 including screening, curing with all lead and lifts of water, scaffolding, taxes and royalty, all complete as per building specifications and direction of E/I

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building speicification and direction of E/I.

Extra for plaster work over exterior surface for each consecutive floors above first floor including cost of scaffolding etc. all complete as per direction of E/I

2nd Floor

Terrace Floor

Labour for laying, fitting and fixing NP2 R.C.C. spu pipe with colars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leak, proof including providing sight rails, bonning rod, night guard, Red light and barrier etc. all complete as per specification and direction of E/I. 150mm dia RCC spun pipe - Upto 3.0 metre depth of invert below G.L.

Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete. 150 MM dia R.C.C. pipe

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 100 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge

Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge

DT : Basic rates for 125/115mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.. (Basic Rates) Drilling upto 30 mtr. Depth below G.L. in Rural Area

Making 6x6mm grooves in plaster surface over walls truely horizontal or vertical as specified. at regular intervals, at all heights including cleaning, finishing, scaffoding and curing wth all leads and lifts of water all complete as per building specification and direction of E/|

Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required, scaffolding, washing of floors, and taxes, all complete as per building specifications and direction of E/I

Providing & Applying high quality acrylic modified resin based texture of Dholpur/Red sand stone Pattern with anti algae and UV resistance properties to be applied as intermediate finish in desired pattern @ 43.04 kgs/10 sqm to form film of 1- 1.5 mm thickness after scrapping and properly cleaning the surface to remove loose particles from the plaster surface, followed by top coating with Premium Acrylic Smooth exterior paint with Silicone additives of required shade by two or more coats @ 1.43 litres/10 sqm, complete as the direction of Engineer -in-Charge.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade

New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Providing two coats of synthetic enamel paint of approved shade and make over new wooden surfaces including preparing the surface after cleaning, removing dirt, scales, smokes, grease and sand papering, including cost of scaffolding and taxes, all complete as per building specifications and direction of E/I

Providing French spirit polishing over new.wooden surface to give desired texture and gloss with approved make and shade of ready mixed French polish including cleaning the surface after removing dirt scales, smokes, grease and sand papering, including cost of scaffolding and taxes, all complete as per building specifications and direction of E/I

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.)

Water proofrng for Old and New Roof Slab :- Providing and laying waterprooflng treatment on roof slab by applying two Component, factory a designed ready to use, acrylic modified flexible,material applied with brush, roller or spray for wate proof i n g coating as per manufactlrer specificatio With following steps :-

(a)surface preparation :-Provrding and cleaning of concrete surface to remove dLrst, oil, grease including removal of existing loose paint / coating, and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from sofftt to identify seepage, leakage. On identiiication of seepage, cement grouting to be done with non shrink expanding admixture of Sika lndia Pvt.Ltd. / MYK Schomberg / Dr Fixit/Fosroc or equrivallent. Providing and reparing of all corners and joinis such as those betr,veen the parapet wall and the roof slab etc shall be chamfered with '150mm X '150 mm fillet of mortar (Cement: sand - 1:4) admixed with acrylic polymer of Sika/ Fosroc/MYK Schomberg/Dr Fixit or equivalent Before chamfering a prime coat shall be given with the sl u rry ?!gc!ylic polyrner Repai rin g su rface irreg ularities, damaged concretein base slab, dead cracks if any, with an acrylic polymer modilied repair moriar ir;cluding a coat of bonding agent of the same with ceme nt slurry rncluding all rnaterial, labour, tools complete.

(b)1st Coat :- Apply 1st coat of two component acrylic modified, ready to use, llexrble cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roller. After 1st coat of application ,45 gsm oI Fibre glass cloth to lay when the first layer is still green. 1st coat should be applied @1.50 kg/SqmUcoat For the fJUrpose of n'ieasurernent tite entire treated surface will be measured."

(c) :2nd Cr:ai :-T,: apply the 2nd coat of two component acrylic modified, reatiy to-use, flexible cementttious material right angle to the '1st coat over the glass fibre liad surface. 2nd coat should be applied @0.7 kgl Sqrnt/coat. For the pltrpose of measurement the entire treated surface will be rneasurecl." Alte r three days of drying the 2nd coat, therainwater ouilets to be plugged and ponding test to be done for 48 hours to rrjerrtify se epage, leal<age from soffit and if found necessary rectification lo be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectifcation to be done as per satrsfaction of E/C protected from damage before screed over it. Watqr proofing Brand:*Sika Topseal 109hi / Fosroc Brushbond RFX/ Dr Fixit Pidiffin 2Kl MYK Aqraiin TG Product Performance - Chemical Base Part A. Acrylic copolmer, Part B Specially graded cementitious powder - Density 1.6 l.rg/l (mixcd density) at +27oC Tensile Strength - 2 lllmm2 after 28 clays (with Fibre cloth) (According to ASTM D 2370)Prillcut Bond Streric;tl-r '-2 I'J/mm2 (concrete lajlqry) (Aqgcrdlglq ISO 4624) Slant-Shear Bond Strength -4 N/mm2 (According to FIP 5.'15) Elongation at Break -35% without Fibre Cloth and 20% wilh Fibre Clot (Accordrng to ASTM D 2370)

(d) Protection of treated surface with PCC- The treated surface should be covered with 25mm/50mm PCC of M-20 grade(1:1.5:3) with proper slope ( '1:120) towards tlre rain outlets in alternatepanels of 2 mt x 2mt keeping 6 mrn gap betuieen the panel joint. lntegralwater proofing admixture conforming to lS 2645 @ of 100 ml per bag of of cement to be added in the scree d concrete(pard separately for thts ltems).-All corners shall be charrmfered with 150mm X 150 mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between pvc pipe outlet and concrete surface slrould be packed properly with rich concrete and the peripheral mouih to be sealed with moisture insensitive epoxy putty of Sika lndia Pvt.Ltd / IVIYK Schomberg / Dr FixiUFosroc .For the purpose ofrreasurement the entire treated surface will be measured."

(e) Groove of PCC surface should be filled with Polysulphide Sealant (Paid Separately) Brand - Sika lndia Pvt Ltd / MYK Schomberg / Dr Fixit/Fosroc Warranty for Five years.

Covering of treated surface wrth PCC :- Providing 25 mm thick Cementn Concrete M20(1:'1.5:3) r'naintaining slope in alternate 2 mIx 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and clcaned sand of F M 2 5 io 3 including screening,shuttering,and mixing cerite nt c0ncrete in mixer with admixture of integral water proofing and placing rn position,strikirrg cLrring,t-a]glgnd royality all complete as per buildirrg specifictionJand direction of E/l.Panels that has been left should be casteci nextday.-lhere should be 6 mm gap between Panels.Brand- Sika *Plastocrate plus,MYK proof WP10, Fosroc- Conplast X421ic , Dr Frx,t Prdiproof LWr

Provrding and filling of 6 mm thick Groove between 25 mm PCC Panels with Polysulphide Sealant (Poring Grade)as per drawings and technical specifications and direction of E in Charge (with 18% GST).Brand:-SikaPolysulphide, Fosroc-l-hioflex 600 Dr. Fixit Pidiseal PS(42P),MYK Seal PS or Euivallent

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

For vertical surface two coats @ 0.70 kg per sqm

For horizontal surface one coat @1.10 kg per sqm.

WATER TANK / LIFT PIT / BASEMENT / SWIMMING POOL: Pressure Nozzle Grouting to be done on construction joints & honey comb / voids areas of RCC by drilling holes, fixing nozzles, pressure injection of cement milk with grouting compound & sealing the nozzle.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including

fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum moisture resistant board

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.

Providing wall panelling with 3.5mm thick teak veneered decorative ply wood of standard make fitted and fixed over 50x12mm sal wood beads at 122mm centres properly screwed to walls including cost of spirit polishing over ply wood and 2 coats of wood preservative paint over the beads of approved shade and make all complete as per specification and direction of E/|.

Providing & fixing on wall face unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia

Providing and fixing on wall face unplaqsticised- PVC moulded fitting/ accessories for unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A,including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Bend 87.5 degree 110x110x110mm

Shoe (Plain) 110mm shoe

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less thaN 440 grams.

Providing and fixing unplasticised PVC pipe clips of approved design to unplasticised PVC rain water pipes by means 50X50X50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc. complete - 110mm

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing & fixing Stainless Steel ( 304 Grade ) Letters on Wall Surface. as per direction of Engineer-In-Charge.

450 mm Hight

Providing & Fixing SS Name Plates, Engraved Lettering , Mounting Through Studs, Thickness of Nameplate 100(mm). Design as per direction of Architect/ Engineer-In-Charge.

Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately.

Providing, Installation, Testing and Commissioning of approved make Aesthetic Passenger Elevator of 10 person capacity, Machine room less (gearless) Elevators, traveling from ground floor to Second floor (3 stops,3 opening,) stopped at all floor and opening on the same side, 1.0m/s speed, DC Door Operator, Automatic rescue device, False ceiling type CD-41, Flooring Vinyl tiles, stainless steel hair finished car and car door (width of door 800mm), Fire rating-60mins etc complete as per specification and instruction of Engineer in charge. The work also include all building/ structural works for supporting arrangement system, necessary scaffolding required for erection of the complete system, necessary wiring and installation of lighting for lift well and lift pit, providing ladder in the lift pit etc. as required complete.

Providing, Installation, Testing and Commissioning of approved make Aesthetic Passenger Elevator of 13 person capacity, Machine room less (gearless) Elevators, traveling from ground floor to Second floor (3 stops,3 opening,) stopped at all floor and opening on the same side, 1.0m/s speed, DC Door Operator, Automatic rescue device, False ceiling type CD-41, Flooring Vinyl tiles, stainless steel hair finished car and car door (width of door 800mm), Fire rating-60mins etc complete as per specification and instruction of Engineer in charge. The work also include all building/ structural works for supporting arrangement system, necessary scaffolding required for erection of the complete system, necessary wiring and installation of lighting for lift well and lift pit, providing ladder in the lift pit etc. as required complete.

Supplying and fixing C.I. cover without frame for manholes : 560 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg

Making soak pit 2.5 m diameter 3.0 m deep with 45x45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Bricks (1K+ 7P = 8 KM.)

Coarse Sand (10KM.)

Stone Chips ( 22 KM.)

Stone Metal ( 22 KM.)

Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I. ‘p’ trap 15 litres C.I. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C. C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of vitreous white glazed earthenware ware footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I.

(A) 580 mm longc) with 10.0 litre low level PVC cistern

Supplying, fitting and fixing flat back or angular, lipped front vitreous white glazed earthen ware urinal of ‘Hindustan "Parry" or any other approved I.S.S make with 5 liters capacity C.I. automatic fulsing cistern of reliance for any other I.S.S. approved make with all fittings with C.I.or R.S. brackets, standard size G.I. flush pipe with fitting clamps,15mm C.I. body brass spindle stop cock of approved quality weight not less than 400grams, 15mm P.V.C./Alkthene pipe 450mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with two coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/I.

(a) Flat back or standig corner (600mmx350mm)

Providing and fixing Gun metal full way valve of approved quality, all complete, as per specification and direction of E/I.

(b) 20mm dia and weight not less than 400gms.

(c) 25mm dia and weight not less than 500gms.

(d) 32mm dia and weight not less than 700gms.

(e) 40mm dia and weight not less than 1.0 Kg..

(f) 50mm dia and weight not less than 1.5 Kg.

Providing and fixing Male ended 15mm dia brass bib cock of approved quality (Wt. Not less than 350 gms) with extra socket all complete as per specification and direction of E/I. :

Earth work in excavation for laying of different types and sizes of R.C.C. spun pipes with disposal of excavated earth within initial lead and lift as per specification and direction of E/I.

(i) For classification of soil item-A

(ii) For classification of soil item-B

Earthwork in back filling the trench after laying different types and sizes of R.C.C. spun pipes with earth removed during excavation within initial lead and lift as per specification and direction of E/I.

Extra for earthwork in all kinds of soil for each additional lift of 1M. or part there of over the initial lift of 1.5M. as per specification and direction of E/I.

Supplying materials and labours for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600x450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600x475mm G.I. Cover with frame (weight not less than 36kg.) along with earth work in excavation and 80 mm thick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.

Cutting chajjas or concrete for laying PVC Pipe and restoring the same with R.C.C. (1:2:4) brick work in cement Mortar (1:4) and cement plaster 1:4 as per specifiction and direction of E/I

Making holes in walls for laying G.I Pipes and restoring the same atfer pipe Laying as per specifiction and direction of E/I (b) 250mm thick wall

Cutting drain width wise above GL for laying H.C.I pipe and restoring brick work in cement mortar (1:4) 12mm cement plaster in C.M. (1:4) with neat cement punning as per specifciation and direction of E/I.

Making holes in wall for laying H.C.I pipes and restoring the same after pipe laying as per specifciation and direction of E/I. (i) 125 mm Dia

Supplying all tolls and labour and cutting chajja cornice for laying H.C.I pipes and making good the same as per specification and direction of E/I.

Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E/I. (all rates have been adopted from the basic rate from SOR + 15% for labour and Contractors profit)

Pillar cock (Long neck) (Ref: Jaquar CAT No-FLR-CHR-5005NB )

Bib cock - (ISI) ( Ref. Jaquar CAT No -FLR-CHR-5047N)

Angular stop cock L.T (Ref: Jaquar CAT No- FLR-CHR-5053N)

Glass shelf 22"

40 mm dia. PVC waste pipe 750mm long with Coupling

15mm C.P. nipple with coupling

Steel jali - 100mm dia.

Providing Solvent cement

Providing and fixing Pressure adjustable shower with revolving joint

Towel ring (Ref: Jaquar CAT No- FLR-ACN-CHR-1121BN)

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I

Mirrors of 6 mm thick plat glass bevelled edge mirror including C.P brass revolving fitting 3mm ply wood board and C.P hinges to fix with mirror. (i) 600mm x 450mm size

(i) C.P. brass towel rail 20mm X 600mm with bracket container

(ii) C.P. brass dish container medium quality with screw and hinges etc.

Providing and fixing 15mm dia and 45cm long PVC connection pipe with heavy quality brass coupling at both ends etc all complete as per specification and direction of engineer in charge

Supply of PVC/XLPE Insulated PVC sheathed , heavy duty armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts (Conforms to IS:1554,part-1)-4 CORE ARMOURED-6 Sq.mm.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

4 X 10 sg. mm (25mm)

Providing and fixing stainless steel A ISI 304 (18/8) kitchen sink as per I.S.13983 with C.I. Brackets, stainless steel plug 40mm including painting of fittings and brackets cutting and making good the walls wherever required. Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Rectangular shape 1500x450 mm

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.

Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.

Granite Stone of approved shade

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall

20 mm nominal outer dia .Pipes.

25 mm nominal outer dia .Pipes.

32 mm nominal outer dia. Pipes.

40 mm nominal outer dia. Pipes.

50 mm nominal outer dia. Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc.

15 mm nominal outer dia .Pipes.

20 mm nominal outer dia .Pipes.

25 mm nominal outer dia .Pipes.

32 mm nominal outer dia .Pipes.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

65 mm nominal bore

80 mm nominal bore

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour.

15 mm nominal bore, weighing not less than 32 gms

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)Single socketed pipes.

75 mm diameter

110 mm diameter

Providing and fixing on wall face unplaqsticised- PVC moulded fitting/ accessories for unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A,including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Coupler 75 mm diameter

Coupler110 mm diameter

Single tee with door 75x75x75 mm

Single tee with door 110x110x110 ,mm

Single tee without door 75x75x75 mm

Single tee without door 110x110x110 ,mm

Bend 87.5° 75 mm bend

Bend 87.5° 110 mm bend

Shoe (Plain) 75 mm Shoe

Shoe (Plain) 110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

75 mm diameter

110 mm diameter

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work

25 mm nominal outer dia. Pipes.

32 mm nominal outer dia. Pipes.

Providing and fixing gun metal non- return valve of approved quality (screwed end) :

40 mm nominal bore Vertical

65 mm nominal bore Vertical

80 mm nominal bore Vertical

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

150 mm dia. R.C.C. pipe

250 mm dia. R.C.C. pipe

300 mm dia. R.C.C. pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : 100x100 mm size P type

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size),foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

With Sewer bricks conforming to IS : 4885

Extra for depth for manholes Size 90x80 cm With Sewer bricks conforming to IS : 4885

Constructing brick masonary road gully chamber 50x45x60 cm with bricks of class designation 75 in cement mortar 1:4 (1 cement :4 coarse sand ) including 500x450 mm precast RCC horizontal grating with frame complete as per standard design .

with common burnt clay F.P.S.(non module) brick of class designation 7.5

Providing and fixing soil, waste and vent pipes : 100 mm dia

Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

75 mm dia

Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :

For 100 mm dia pipe

For 75 mm dia pipe

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm dia

Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

75 mm dia Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing plain bend of required degree. 100 mm dia

Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

75 mm dia Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 75 mm outlet

Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :

100 mm dia

75 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge

65 mm dia

80 mm dia

65 mm pipe (19mm thick insulation)

80 mm pipe (19mm thick insulation)

Supplying &installation of approved make required capacity single phase, 50 Hz,240V, centrifugal mono-block pump, with starter, connections, base channel foundation etc. as required as per specifications but excluding pipe and connection cable.(Required for : Water uplifting)

2.0 HP head metre 12-20, discharge LPM 540-180

Air release Valve / Drain Valve

Multi Level Float Switch-50mm

Providing, fixing, jointing and testing heavy duty, polyethylene (PVC) SWR pipes, -Pvc rigid pipe ISI 40MM 6Kg Pressure, open, low density, to wall, ceiling and floor, approved quality, complete, for soil and waste water drain including jointing with rubbering / solvent / solution and airtight joints, with necessary specials, couplers, elbow, equal tees, tail piece, adapter (both male and female), reducer (single stage, double stage and triple stage), end cap, fabricated bend, etc., and lubricant or jointing material, including testing, cutting, making good the wall, ceiling and floor etc. complete of the following nominal bore (NB) size: 40 mm diameter

Providing, installation, testing and commissioning stainless steel strainer 80mm dia

Providing, installation, testing and commissioning stainless steel strainer 65 mm nominal bore

Supplying and fixing IGH bathroom mirror of thickness 4.01, Size- 1200X900

Providing & fixing wall hung E.W.C. (Ref: Jaquar CAT No- CNS WHT- 963UFSM)

Providing & fixing flusing tank Single Piece slim concealed Cistern body. (Ref: Jaquar CAT No- JCS-WHT-2400)

Providing & fixing control plate (Ref: Jaquar CAT No- JCP-CHR-152415)

Providing & fixing Toilet Roll Holder. (Ref: Jaquar CAT No- ACN-CHR-1151N)

Providing & fixing 2 way bib cock with wall flange. (Ref: Jaquar CAT No- FLR-CHR-5041N)

Providing & fixing counter top basin size : 610X415X160 MM (Ref: Jaquar CAT No- DRS-WHT-37601)

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes ,royalty etc all complete job as per direction of E/I.

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Supply fitting and fixing lowering 50 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

Trenching in ordinary soil up to a depth of 60cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage complete (by mechanical transport upto 5Km lead) (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment).

Supplying and stacking at site dump manure from approved source, including carriage complete (by mechanical transport upto 5Km lead) (manure measured in stacks will be reduced by 8% for payment): Screened through sieve of I.S. designation 16mm

Rough dressing the trenched ground including breaking clods.

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Fine dressing of the Ground.

Spreading of sludge, dump manure or/and good earth in required thickness as per direction of officer-in-charge (Cost of sludge, dump manure or/and good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the officer-in-charge.

Preparation of beds for hedging and shrubbery by excavating 60cm deep and trenching the excavated base to a further depth of 30cm. efilling the excavated earth after breadking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20%: one part of stacked volume of sludge or manure after reduction by 8% ) flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, with in a lead of 50m lift up to 1.5 m complete (cost of sludge, manure of extra earth to be paid for separately).

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately):

Holes 1.2 m dia and 1.2 m deep.

Holes 90 cm dia, and 90 cm deep.

Complete maintenance of trees (Out side garden features), jobs like making of basin at regular interval i/c watering, weeding, pruning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge. Trees for 300 No. (4-8 & 5-6 year Slow & Fast growing group) ( 18 Manth Per Tree 175x 18 = 11484.00)

Half brick circular tree guard in bricks, internal diameter 1.25 metre and height 1.2 metre above ground and 0.20 m below ground, bottom two courses laid dry and top three courses in cement mortar 1:6 (1 cement : 6 fine sand) and the intermediate courses being in dry honey comb masonry as per design complete: With common burnt clay F.P.S. (non modular) bricks of class designation 5

TREES

Alstonia scholaris of plants height 150-165 cm. in bag of plants size 25 cm

Azadirachta indica ( Neem ) of plants height 120-130cm in big polybag of plants size 25 cm

Cassia fistula (Amaltash) of plants height 120-135 cm. in big poly bags of plants size 25 cm

Delonix regia (Gulmohar) of plants height 150-165 cm. in big poly bags of plants size 25 c

Ficus benjamina (green) of plants height 120-135 cm. with 6-8 branches and lush green foliage in gunny bags of plants size 25 cm

Fishtail palm of plants ht. 150-180 cm bottom girth 15-20 cm well developed in big poly bags of plants size 25 cm

Foxtail palm of plants ht. 120-150 cm bottom girth 15-20 cm well developed in big poly bags of plants size 25 cm

Jacaranda mimosifolia of plants height 150-165 cm. in big poly bags of plants size 25 cm

Mangifera indica (Mango-grafted ) of plants height 60-75 cm. in big poly bag of plants size 25 cm

Plumeria alba of plants height 120-135 cm. with 2-3 branches in bags of plants size 30 cm

Polyalthia longifolia (Ashok) of plants height 150-165 cm. in earthen pots of plants size 25 cm

Eugenia jambolana (Jamun) of plants height 150-165 cm. in big poly bags of plants size 25 cm

OKNAMENTAL PLANTS

Providing Plant Dahlia single in different colour with fresh & healthy foliage well developed with 6 to 8 half blooming buds in 20 cm Earthen Pot/Plastic Pot.

Providing Plant Daisy well developed with fresh & healthy foliage in full bloom in 20 cm Earthen Pot/Plastic Pot.

Providing Plant Salvia red Hybrid dwarf variety having 15 to 23 cm ht., specimen 6 plants with fresh & healthy foliage in full bloom well developed in 35 cm Earthen Tray/ Nand

Providing Plant Budded Rose (H.T. variety) 3 to 4 healthy branch 30 cm and above ht. well developed with one and above flower plant in 20 cm Earthen Pot,

Washingtonia filifera palm well developed 90 to 105 cm ht. plant having 5 to 6 straight fresh and healthy leaves in 35 cm Cement Pot

SHRUBS

Supply and stacking of plant Cassia biflora of height 45-60 cm. in earthen pots of size 20 cm

Supply and stacking of plant Ficus panda of height 30-45 cm. with 3-4 branches and healthy foliage in p.bag of size 20 cm

Supply and stacking of plant Hamelia patens of height 30-45 cm. with 3-4 branches in poly bags of size 20 cm

Supply and stacking of plant Hibiscus variegated of height 60-75 cm. with healthy variegated foliage in earthen pots size 25 cm

CREEPER PLANTS

Allamanda cathartica plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots

Bougainvillea (Variety Butiana, Lady Mary Baring, Mahara,Mohan, Scarlet Queen, Varigata, Glabra Formosa, Peruviana Odissi, Partha, Subhra,Thimma, Spectabilis L.N Birla, Refulgens) plant of height 30 cm. to 45 cm. with 2-3 branches in 20 cm size of Earthen pots / Plastic pots.

Quisqualis indica plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots

FOLIAGE/SHADE LOVING PLANTS

Providing of Areca Palm plant, having ht. 1.20 m to 1.50 m with 5 to 6 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot / Plastic pot.

Providing of Areca palm plant, having ht. 1.50 m to 1.80 m with 6 to 8 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot / Plastic pot.

Providing of Croton Golden plant, having ht. 45 cm to 60 cm with 2 to 3 branches, well developed, fresh and healthy foliage in 25 cm size of Earthen pot / Plastic pot.

Providing of Diffenbachia Tropicsnow plant, having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot / Plastic pot.

Providing of Draceana Song of India Green plant (three in one), having ht. 30 cm, well developed, fresh & healthy, lush green foliage from bottom to top in 20 cm size of Earthen pot / Plastic pot.

Point Wiring in Medium Class PVC Conduit, with Modular type Switch:- Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 Sq.mm FR PVC insulated copper conductor single core cable in surface/recessed with PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required. FR PVC Copper Wire (Confirming to IS: 694-2010, 1.1 KV) :- Make:- Havells, Polycab, Rajnigandh, RR Cable. (Make of Modular switch Sockets:- Havells (ATHENA), L&T ENGLAZE), Legrand (LYNCUS) , Anchor(WOODS), Schneider-(OPEL)

Group-C

Twin Control Point Wiring in PVC Conduit, with Modular type Switch:- Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed Medium Class PVC conduit, 2 way modular switch, modular plate, suitable size of GI box earthing the point with 1.5 Sq. mm FR PVC insulated copper conductor single core cable etc as required. FR PVC Copper Wire (Confirming to IS: 694-2010, 1.1 KV) FR PVC Copper Wire (Confirming to IS: 694-2010, 1.1 KV) :- Make:- Havells, Polycab, Rajnigandh, RR Cable. (Make of Modular switch Sockets:- Havells (ATHENA), L&T ENGLAZE), Legrand (LYNCUS) , Anchor(WOODS), Schneider-(OPEL)

Power plug wiring in PVC conduit (2x4 sq.mm.):- Wiring for light/power plug with 2x4 Sq.mm FR PVC insulated copper conductor single core cable in surface/recessed Medium Class PVC conduit along with 1 No. 4 Sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc. as required. FR PVC Copper Wire (Confirming to IS: 694-2010, 1.1 KV)Make:- Havells, Polycab, Rajnigandh, RR Cable.

Circuit/Sub-main wiring in PVC Conduit:- Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper condcutor, single core cable in surface/ recessed Medium Class PVC conduit as required. FR PVC Copper Wire (Confirming to IS: 694-2010, 1.1 KV) Make: Havells, Polycab, Rajnigandh, RR Cable.

2x1.5 Sqmm + 1x1.5 sqmm earth wire

2x2.5 Sqmm + 1x2.5 sq mm earth wire

2x6.0 Sq.mm + 1x6.0 Sq.mm earth wire .

2x10 Sq.mm + 1x6.0 Sq.mm earth wire .

4x6.0 Sq.mm + 2x6.0 Sq.mm earth wire.

4x10 Sq.mm + 2x6.0 Sq.mm earth wire.

Telephone Wiring in Existing Conduit:- Supplying and drawing, following pair, 0.5 sq.mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed steel / PVC conduit as required. (TEL Wire Confirming to IS: 694-2010, 1.1KV) Make:-Havells, Polycab, Rajnigandh, RR Cable. 2 pair

TV Cable in Existing Conduit:- Supplying and drawing Co-axial TV Cable RG-6,0.7mm solid copper conductor PE insulated,shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed PVC conduit as required. (Confirming to IS: 694-2010, 1.1 KV) Make:- Havells, Polycab, Rajnigandh, RR Cable.

S/F PVC Conduit: Supplying and fixing of following sizes of med Class PVC conduit of 2 mm thick along with the accessories in surface / recess & cutting the wall and making good the same in case of recessed conduit as required . (Make:- Polycab, Precision, AKG)

Supply and fixing of following size PVC/G.I. box on surface /recess with suitable size of phenolic laminated sheet cover in front including painting etc as required. 75mmx75mmx60mm deep.

S/F Modular type Switch / Socket:- Supplying and fixing of following switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as requried. (Make of Modular switch Sockets:- Havells (ATHENA), L&T ENGLAZE), Legrand (LYNCUS) , Anchor (WOODS), Schneider-(OPEL)

5/6 amps switch

15/16 amp switch

3 pin 5/6A socket outlet

6 pin 15/16 amp socket outlet

Telephone socket outlet

TV antenna socket outlet

S/F Modular type electronic fan regulator:- Supplying and fixing 2 modules Stepped type electronic fan regulator on the existing modular plate & switch box including connections but excluding modular plate etc. as requried. (Make :-Havells, Legrand , Anchor, Schneider.)

S/F Modular blanking plate:- Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. (Make - Havells, Legrand , Anchor, Schneider.)

Supply and fixing of following size/ modules, GI box along with modular base & cover plate for modular switch/ regulator in recess, including connection as required. (Make :- Havells, Legrand , Anchor, Schneider).

1or 2 module (78mmx 78mmx 45mm)

4/5 module (78mm x 140mm x 50mm)

6 module (78mmx 205mmx 50mm) (for 2 nos. 6A Sockets & 2no. 6A Switch)

S/F Light plug point with modular type accessoris:- Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 Amp modular socket outlet and 5/6 A modular type switch, connections painting etc. as reqd. (for Light plug point). (Make:-Havells, Legrand , Anchor, Schneider, L&T.)

S/F Power plug ponit with modular type accessories:- Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 Amp modular socket outlet and 15/16 A modular type switch, connections painting etc. as reqd. (Make:- Havells, Legrand , Anchor, Schneider, L&T.)

S/F Ceiling Rose:-Supplying & fixing of 2 pin, 5 amp Ceiling rose on the existing junction box/ wooden block including connection etc. as required. (Make:- Anchor, Kona)

S/F Batten / Angle Holder:- Supplying and fixing brass batten/angle holder including connection etc. as required. (Make:- Anchor, Kona)

S/F Electronic Musical Call Bell Supplying and fixing of Electronic Musical call bell suitable for single phase, 230 V, complete as required. (Make:- Anchor, reputed)

ITC fluorescent fitting directly on surface:- Installation, testing and commissioning of suspended pre-wired ,fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc., directly on ceiling or on wall including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

ITC fluorescent fitting with Down Rods:- Installation, testing and commissioning of suspended pre-wired ,fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc., including supplying and fixing ball and socket arrangement, 2 Nos. down rods of 20 mm dia X 1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

ITC ceiling fan:- Installation, testing and commissioning of Ceiling fan, icluding wiring the down rods os standard length (Up to 30Cmm) with 1.5 sq. mm FR PVC insulated, copper conductors, single core cable etc. as required.

ITC exhaust fan upto 450 mm sweep:- Installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

S/F MCCB in Panel Board:-Providing and fixing following rating and breaker capacity MCCB with thermomagnetic release and thermal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

25-100 amps, 16 KA fixed thermal setting

S/F SP MCB DB:- Supplying and fixing following way, SP&N MCB doubel distribution board of sheet steel for 240 Volts on surface /recess complete with tinned copper bus bar, neutral busbar, earth bar, detachable gland plate, interconnections, phophatized and powder coated painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR). (Make:-SIEMENS-Bitaguard, LEGRAND-Ekinox³-, SCHNEIDER-ACTI-9, L&T-AU)

8 Way Double Door

12 Way Double Door

16 Way Double Door

S/F TP MCB DB: - Supplying and fixing following way, horizontal type double door three pole & neutral, sheet steel, MCCB distribution board, 415V, on surface/ recces , complete with tinned copper bus bar, neutral bar, earth bar, din bar interconnections, powder painted including earthing etc. as required (But without MCCB/RCCB/Isolator) (Make:-SIEMENS-Bitaguard, LEGRAND-Ekinox³-, SCHNEIDER-ACTI-9, L&T-AU

6 ways (4+18) Double Door. (horizontal type)

8 ways (4+24) Double Door. (horizontal type)

S/F VERTICAL TYPE T.P. MCCB DB:- Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCCB distribution board of sheet steel dust protected, duly power painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar mounting MCCB's (but without MCCB's and Incomer) as required. Note : Vertical type MCCB TPDB is normally used where 3 phase outlets are required. (Make:-SIEMENS-Bitaguard, LEGRAND-Ekinox³-, SCHNEIDER-ACTI-9, L&T-AU

4 way (8 + 12) Double door, Vertical Type

S/F 'C' Series MCB:- Supplying & fixing 5 amps to 32 amps rating 240/415 volts 10 kA, 'C' curve Miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. ( Make:-LEGRAND- DX³/SCHNEIDER- ACTI-9/ABB-S200MSIEMENS- BETA GUARD/ L&T- AU VERSION).

6-32 Amps. Single Pole

6-32 Amps Double Pole

40 Amps Double Pole

6/32 Amps TPN

50/63 Amps TPN

S/F SP MCB Blanking Plate:- Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.(Make:- L&T, Legrand, Schneider,Siemens)

S/F SPN RCCB:- Supplying & fixing following rating double pole (Single Phase & Neutral) 240 V, Resudual Curren Circuit Breaker (RCCB) , having a sensitivity current uo to 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. (Make:- LEGRAND- DX³/SCHNEIDER- ACTI-9/ABB-S200MSIEMENS- BETA GUARD/ L&T- AU VERSION.)

P/F MV Danger Notice Plate:- Providing & fixing of M.V. danger notice plate of 200 mm x 150 mm, made of mild steel, at least 2 mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side as required.

P/F HT Danger Notice Plate:- Providing & fixing of H.T. danger notice plate of 250 mm x 200 mm, made of mild steel, at least 2 mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side as required.

G.I. Pipe Earthing:- Earthing with G.I. Earth Pipe 4.5 Meter long , 40mm dia including accessories, and providing massonry enclosure with cover plate having locking arragement and watering pipe etc. with charcoal/cock and salt as required.

Main LT Panel- 2 nos

APFC Panel - 2 nos.

Pump Panel- 2 nos.

3 nos.Lift Machines - 2x3= 6 nos.

Transformer Body Earthing:- 2 nos.

DG Set Body Earthing :- 2 nos.

Total - 16 Nos.

Earthing with copper Earth plate 600mm x 600mm x 6mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal and salt as required).

UPS - 2 nos.

Equiopment Rack CCTV- 1 no.

EPBEX MACHINE 1 no.

Server Rack 1 no.

Transformer- Neutral Pits:- 2 nos.

DG Set Neutral Pits 2 nos.

Total - 5 Nos.

Supplying and laying of 8 SWG G.I. copper wire at 0.50 meter below ground level for conductor earth electride, including soldering etc. as required.

S/L 25mmx5mm G.I. strip as strip earth electrode :- Supplying and laying 25 mm X 5 mm GI strip at 0.50 meter below ground/surface as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm).

providing and fixing 25mm X 5mm copper strip on surface or on recess for connectio etc. required

P/F G.I. lighting conductor finial:- Providing and fixing of Lightning Conductor finial, made of 25 mm dia 300mm ling, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Reverting, Sweating and soldering Lightning Conductor Tape:-

Reverting, Sweating and soldering of Copper/G.I. Tape (with another Copper/G.I. tape, base of the finial or any other mettalic obect) as requried.

P/F G.I. lightning conductor tape in horzontal run :-

Providing and fixing G.I. Tape 20mmx3mm thick on parapat or surface of the wall for lightning conductor complete as required. (for Horizontal Run).

P/F G.I. lightning conductor tape in Vertical run:-

Providing and fixing G.I. Tape 20mmx3mm thick on parapat or surface of the wall for lightning conductor complete as required. (for Vertical Run).

P/F Testing joint for GI lightning conductor :-

Providing and fixing testing joint made of 20mm * 3mm thick GI strip 125mm long. With 4 nos. of GI bolts. Nuts chuck nuts and spring washers etc. complete as required.

G.I. Pipe electrode with Salt/Charcoal:-

Earthing with G.I. Earth Pipe 4.5 Meter long , 40mm dia including accessories, and providing masonry enclosure with cover plate having locking arragement and watering pipe etc. with charcoal and salt as required.

S/L 25 x 5mm G.I. earth strip in 50 mm below ground:-

Supplying and laying 25mmx5mm G.I. Strip at 0.50 meter below ground as strip earth electrode, including connection/ termination with G.I. nut bolts, spring washer etcas required. (Jointing shall be done over and 2 sets of G.I. Nut Bolts & Spring washer spaced at 50mm).

MV Cable Laying up to 35 sq. mm. in ground :-

Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size not exceeding 35 sq.mm. direct in ground including excavation, sand cushioning, protective covering by 2nd class bricks and refilling the trench etc as required.

MV Cable Laying up to 95 sq. mm. in ground :-

Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size exceeding 35 sq.mm. but not exceeding 95 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required

MV Cable Laying up to 185 sq. mm. in ground :-

Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size exceeding 95 sq.mm. but not exceeding 185 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required

MV Cable Laying up to 400 sq. mm. in ground ;-

Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size exceeding 185 sq.mm. but not exceeding 400 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

MV Cable One Number additional Laying up to 400 sq. mm. in ground ;-

Laying of one number additional PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size exceeding 185 sq.mm. but not exceeding 400 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of grade of size exceeding 1.1 KV but not exceeding 11 KV of size not exceeding 120 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

CABLE ROUTE MARKER:- Supplying and making cable route marker with cement concrete 1:2:4 (1 Cement :2 Coarse sand ;4 gradced stone aggregate 20mm nominal size ) of size 60cmx60cm at the bottom and 50cmx 50cm at the top with a thickness of 10 cm including inscription duly engraved as required.

Supply, installation, testing and commissioning of of following size ceiling fan 3 blades confirming to IS:- 374:2019 including wiring tne down rods, of standard length (up to 30 cm) with 1,5 FR PVC insulated, copper wire suitable for 230 Volts, 50 Hz, single phase supply etc. complete as required.( BLDC 5 Star (32 Watt) IS:374:2019 (energy efficient fans and two yeas warranty ) (Make & Model nos. of Fans are to be approved by Engineering Incharge & Consultant before procurement.)

Supply of 48" (1200 mm) Sweep Ceiling fan BLDC 5 Star (32 Watt) IS:374:2019 (energy efficient fan. Make :Usha/Crompton/ Havells/GEC.

SITC of 230 mm (9") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required. Make :- Usha/Crompton / Havells /GEC.

SITC of 300 mm (12") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required. Make :- Polar/Usha/Crompton / Havells . .

SITC of 400 mm (16") sweep AC 230/250 volts, 50 HZ Wall Mounting Revolving Fan with brackets, cooper winding, etc. complete all electric room etc. Make :- /Usha/Crompton / Havells /GEC.

All the LED lamp shall be of minimum 60 or above lumens per watt and the LED BATTEN TUBE LIGHTS & other LED light fixtures shall be of 100 or above lumens per watt. LM 79 and LM 80 reports need to be submitted with all accessories by the contractor. All LED Lights (Make & Model nos. of LED Liughts are to be approved by Engineering Incharge & Consultant before procurement.) Burning Hours should be less than 35000 to 50000 hrs. Make:-Havells/Sygnify-Philips/ Bajaj/ Jaquar .

SITC of following rating recess/surface mounted LED round/square shape Down Light Luminarie with pressure die-cast housing for single phase supply voltage. Luminarie shall be confirm to IS; 10322 part-5/section-2 or IEC 62722 with all necessary accesoreies as required. (100l/w , 5700K Cool white, rated voltage- 220/240V. (LM 79 and LM 80 reports need to be submitted , 50,000 burning hrs, and two years warranty) Make:-Havells/Philips/Bajaj/ Jaquar. Make 0f LED Philips/Osram/Cree/Nichia.

12 W Round Down light Surface

15/16 W Round Down light Recess

15/16 W Round Down light Surface

SITC of following rating surface mounted LED 4ft Batten tube light fitting suitable for 230V, 50 Hz, single phase supply etc all complete as required. wall mounted LED type batten fitting complete with electronic diver and LED etc. directly on wall including connections with 1.5 Sq. mm FR PVC insulatted copper conductor and earthing the body etc. as requiered. (LM 79 and LM 80 reports need to be submitted , 50,000 burning hrs, and two years warranty) Make:-Havells/Philip/ Wipro/ Jaquar 20/22 W LED Tube Light (4 FT) Batten type.

All the LED lamp shall be of minimum 60 or above lumens per watt and the LED BATTEN TUBE LIGHTS & other LED light fixtures shall be of 100 or above lumens per watt. LM 79 and LM 80 reports need to be submitted ). Make:-Havells/Philips/ Wipro/ Jaquar . Make 0f LED Philips/Osram/Cree/Nichia.

Supply of 9W/10W LED Bulb in existing holders. (Confirming to IEC : 62722)

Supply of double LED Tube light Fitting made of diacast aluminium housing 2x20W LED Bettle Tube light sritable for surface or suspended mounded suitable for 230V, 50 Hz, single phase supply etc all complete as required, complete with electronic diver and LED etc., including connections with 1.5 Sq. mm FR PVC insulatted copper conductor and earthing the body etc. as requiered. Efficacy is 100 lm/W.temperature (5700K ± 355K. @L70 & Lumen maintenance as per L70 (Confirming to I.E.C. 62722)

Supplying and fixing Surface mounted 9/10 Watt CFL / LED type bulk head e comprising of pressure die casr housing with acrylic diffuser (IP65) and complete with integrated electronic driver etc. directly on wall /ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc as required. LM 79 and LM 80 reports need to be submitted, 50,000 burning hrs, and two years warranty).

SITC of LED 2 ft Mirror light with power 8/10W, rated voltage 230W, 50 HZ, aluminium /PC body with running life minimum 30000 hrs. ( LM 79 and LM 80 reports need to be submitted)

SITC of 2x5W LED outdoor UP-DOWN light with IP:65 protection, die cast aluminium housing .(LM 79 and LM 80 reports need to be submitted , 50,000 burning hrs.)

SITC of 2x8W LED outdoor UP-DOWN light with IP:65 protection, die cast aluminium housing. (LM 79 and LM 80 reports need to be submitted , 50,000 burning hrs,)

SITC of Recess monting LED Panel Light 2x2 (36W) IEC:62722 or SI:10322 part-5 /section 2. (LM 79 and LM 80 reports need to be submitted, 50,000 burning hrs,).

SITC of LED type Name Plate as per the direction of E/I like Reception, Banquet Hall, Restarant, Reception, Kitchen, Room with number, Toilet/HE/SHE, PARKING, PanelmRoom,Server Room etc. ( as approved by consultant)

Gate Light for Main Entrance :- Supply, fitting, fixing , connection and testing of 20/25 Watt opal of approvedmake LED Post of Lamp made in die castalluminium housing with decorative clear /Opel acrylic diffusier and IP 65 Protection IS:- 10322 part 3/Section3 and along with all accessories G.I.Pipes, brackets, wiring as per installation DWG. (LM 79 and LM 80 reports need to be submitted , 50,000 burning hrs)

SITC of approved make LED Bollard Light fitting with Cylindrical shape and height 600 to 850mm , 8/9 Watt with die casr alluminium housing opel with PC Duffusier , IP/65 Is 10322 Part-5 . (LM 79 and LM 80 reports need to be submitted , 50,000 burning hrs)

SITC of following rating 90 /100 W LED Street Lighting Luminarie with pressure die-cast housing and toughened glass cover, IP-66 protection, LUMINOUS EFFICARY 110/lm/w, with lens in existing pole or pipe for supply voltage, 100-270V, AC, 50Hz, luminarie shall be confirm to IS; 10322 part-5/section-3 a ) (LED light fixtures shall be of 100l/m or above. (LM 79 and LM 80 reports need to be submitted , 50,000 burning hrs)

Supply fitting and fixing of PVC/XLPE insulated PVC sheathed heavy duty Al. armoured cable for working voltage up to and including1100 Volts confirming to IS 1554 (part-1) Make:- Havells, KEI, Finolex, Polycab.

2 Core 6 Sq. mm

4 Core 10 Sq. mm

3.5 Core 25 Sq. mm

3.5 Core 35 Sq. mm

3.5 Core 95 Sq. mm

3.5 Core 150 Sq. mm

3.5 Core 300 Sq. mm

20 KVA ON Line UPS (3 Ph. Input & 3 Ph. Output) With Accessories

Supply, fitting, fixing and testing of 1 no. 20 KVA in parallel redundant mode with SMF back-up batteries suitable for 30 minutes configuration with :- 415V, 3ph input & 3 ph output ON-LINE UPS system backup protection for 90 minutes and all standard accessories as required. The Inverter will have in built protection for ground fault, DC reverse polarity, DC over voltage and current limitation, AC short circuit, AC over Voltage and current limitation. The UPS technology should consists of high double-conversion efficiency IGBT Based rectifier on line type UPS.The details are as follows:-

Supply, fitting, fixing, testing and installation of 1 no. 20 KVA, ON Line UPS three phase input and three phase out put power system of in put voltage 360V/380/V/400V/485V AC , Frequency range 40 HZ to 60 Hz, +/- 10% and out put voltage range 415V +/-1%, AC frequency range, 50Hz, +/-1% poower factor 0,8/3.1, Harmonic distrortion -< 2% THD (Linear Load): 5% THD (Non- Liniear Load) along with required Batteries, Battery Stand, UPS Box Battery Lead etc as required. (30 minutes back up ) Make UPS:- Numeric (Legrand), APC (Schneider), Vertive(Emersion)

Configuration of UPS :-

3 Phase input & 3 Phase output

The above mentioned on-line UPS must have following features

1) Upgradeability :- Suitable for paralleling up to 3 nos. of 20 KVA UPS, and Should be upgradable to work as parallel redundant UPS in load sharing mode.

2) Intelligent LCD display with event logging facility.

3) Double conversion.

4) Built in paralleling kit.

5) IGBT technology for Rectifier and Inverter.

6) Split Static, Manual & Maintenance Bypass.

7) Input power factor correction less than 0.95.

8) Input harmonic distortion less than 5% at 50% load. with the application of IGBT(Insulated Gate By polar Transistor) based rectifier, but 6/12 pulse is not applicable.

9) Software communication :- RJ-45 port to communicate with BMS and Should be SNMP (Simple Network Management protocol) compatibility.

10) Phase reverse sequence operation

11) Automatic static bypass

12) Maintenance Bypass.

13) Technology : Micro processor based controls, true online, double conversion type, should have cold start facility.

14) Overall minimum Efficiency :>93.8 %

15) Isolation ;- Built inl isolation transformer at the output of UPS System.

16) Charger :- Should have built in charger of minimum 10 Amp. (separate from rectifier)

17) IGBT bith side input and inverter side

18) SNMP Kit card.

19) Parallel Redundant Kit

20) Input phase correction kit.

21) Back-up time :- 30 min. with SMF Batteries.

Cost of 20 KVA ON LINE 3 Phase in and 3 Phase out UPS

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

SITC of MS Battery Rack suitable for 15 to 20 UPS Battery Installation.

SITC of 100Amp. DC Breaker with UV relay Coil. Make:- L&T, Siemens, Schneider, Legrand

SITC of 18 nos. 100 AH Sealed Maitanace Free (SMF) Battery with 24 months replacement guaranty. IS:1652:1991. (VAH Required 21600 for 20 KVA UPS (100AH x 18 Nos. x 12V = 21600 VAH) Make:- Battery-Exide, Amar-Raja, Quantum.

Total Cost of 1 Set 20 KVA UPS, Batteries & Accessories (A+B+C+D)

SPLIT AC AND VOLTAGE STABILIZER

SITC of 1.5 Ton 5 Star High wall Split AC Inverter Type IS:1391, Part-1 or Part-11(Hot and Cold) Unit of BEE Rating, (Generally conforming to IS 1391 latest) Inverter (Variable Speed), Heating Mechanism-Electric Heater, Minimum SetTemperature-12 degree Celsius, Maximum SetTemperature-40 degree Celsius, Remote Control, with original company make out door structure including rigging of indoor out door units, pressure testing vacuumingising etc as required. Make:- Blue Star/Hitachi /Carrier. (CATEGORY A or B)

SITC of 2 Ton 5 Star High wall Split AC Inverter Type IS:1391, Part-1 or Part-11 (Hot and Cold) Unit of BEE Rating, (Generally conforming to IS 1391 latest) Inverter (Variable Speed), Heating Mechanism-Electric Heater, Minimum SetTemperature-12 degree Celsius, Maximum SetTemperature-40 degree Celsius, Remote Control, with original company make out door structure including rigging of indoor out door units, pressure testing vacuumingising etc as required. Make:- Blue Star/Hitachi /Carrier/Mitsubishi. (CATEGORY A or B)

SITC of wall mount suitable capacity (4 KVA) Automatic Voltage Stabilizer, voltage range 140V to 280V of copper wound Transformer along with suitable size of connectors. (in & out) Make:- Sen & Pandit/V Guard/ Blue Star. (To use for 1.5 Tr Split AC)

Supply, fitting, fixing of wall mount suitable capacity (5 KVA) Automatic Voltage Stabilizer, voltage range 140V to 280V of copper wound Transformer along with suitable size of connectors in & out. Make:- Sen & Pandit/V Guard/ Blue Star

AC Accessories

SITC of Copper Tube of Size 1/4" for Split AC Unit 1/1.5/2/3 Tr Capacity including nitide rubber insulation.

SITC of Copper Tube of Size 1/2" for Split AC Unit 1/1.5/2/3 Tr Capacity including nitide rubber insulation.

SITC of Copper Tube of Size 3/8" for Split AC Unit 1/1.5/2/3 Tr Capacity including nitide rubber insulation.

SITC of Copper Tube of Size 5/8" for Split AC Unit 1/1.5/2/3 Tr Capacity including nitide rubber insulation.

SITC of Drain Pipe for Split AC Unit

SITC of Outdoor Stand for 1.5 Tr Split AC Unit

SITC of Outdoor Stand for 2.0 Tr Split AC Unit

SITC of FR PVC Insulated 3C, 4 Sq. mm Copper Wire.

82.5 KVA Silent D.G. Set with AMF Panel IS/IEC - 60034-1, IS:1460, IS:13018 :-

Supply, fitting, fixing, installation and testing of 82.5 KVA /415 Volts, 3 Ph. Silent Diesel Generator Set with AMF Panel confirming to IS/IEC - 60034-1, IS:1460, IS:13018

The 82.5 KVA /415 Volts, 3 Ph. Silent Diesel Generator Set with AMF Panel shall have AC supply complete with engine (1500 RPM) and alternator with accessories including residential type silencer and fuel service tank, battery, nattery leads, battery charger with all accessories, including MCCB of suitable rating & standard set of tools and anti-vibration mounting pads, etc. The power command controller compactable with BMS, PC & PLC compelte as required, remote mointoring and data logging with digital voltage regulator through inbuilt AVR, digital governing including protection complete as required. Make:-Kohler/Jakson/Sterling.

Supply of company make acoustic enclosure for 82.5 KVA CPCB approved Acoustic enclosure with 80 mm MS base plate, 2 mm CRCA sheet, 50 mm thick foam / 100 mm Rock Wool Insulation, 14 surface tank treatment, dully powder coated and painted with suitable colour with integrate Fuel Tank, services door, louvers (Fresh Air / Radiator), 1020 dia residential type Silencer, dimension as per company specification, complete with following accessories :-

a) Fuel Tank.

b) Batteries, battery leads and in built battery charger.

c) Residential Silencers.

d) First fill of lube oil.

e) AVM Pads.

f) OEM Manufacured AMF Panel with 250A /FP/36kA/MCCB /Microprocessor release.i( with nbuilt Control Breaker ( of suitable capacity of 630A MCCB Microprocessor release type with spreader links & extended rotary handle) and all type of meters (Voltmeter, Ammeter, KW/m, Hz/m, contractor, AMF Conroller etc as required ) and all other protections.

In above supply item following work are also included :- i) Installation, fitting, fixing, testing and commissioning of the same. ii) Civil part for commissioning of D.G. Set as per civil rates for construction of platform. (Foundation of Platform shall be in he scope of Civil Part) iii) Installation of Exhaust system for D.G. Set shall be as per Central & State Pollution Board Norms along (C.P.C.B.) iv) Test run for D.G. Set without load and with load (part wise ) at least 2hrs each time shall be in the scope of Contactor.

Supply of inbuilt Control Breaker (of suitable capacity of 250A/36KA/FP MCCB Microprocessor release type with spreader links & extended rotary handle) with separate AMF Panel having 250A F/P MCCB, Microprocessor release type with spreader links & extended rotary handle, AMF Controller, F/P NO NC 250A Contactor, and all type of meters (Voltmeter, Ammeter, KW/m, Hz/m) and all protection indications with alarm and with suitable arrangement for 1R 150 Sq mm 3.5 Core Al. Ar. Cable etc as required.

Cost of 82.5 KVA DG set with AMF Panel

G.I. OCTOGONAL POLES

Supply of 7 Meter Height Octagonal Hot Dip Galvanized pole (BOP 7030) with top dia 70mm bottom dia 130mm & made of 3 mm thickj sheet, base plate dimensions 200x200x12mm (L X B X T) including suitable sizes of foundation bolts all complete as required. (Without ARM) Make:- RR Ispat/ Transrail/ Valmount/Bajaj.

Installation, Testing and commissioning of 7 Meter Height Octagonal Hot Dip Galvanized pole with suitable Tools and Plants, wiring of Luminaires with all materials and construction of shallow foundation, with M25 grade concrete considering safe soil bearing of 10T/mtrs Sq.

Supply fitting, fixing of Double Arm (2 Mtr. Long)suitable for 70 mm Top

Supplying and fixing of following switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as reqd.

Bell push

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. (23AWG Cable) Make- Legrand-,Schneider- Actasis, Optronix

1 run of Cable

Supplying & fixing 5 amps to 32 amps rating 240/415 volts 10 kA, C curve Miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Triple Pole

HOT DIPPED GALVANIZED IRON CABLE TRAY

Supplyig and installing following size of Hot Dipped Galvanised Iron cable trays (Galvanised thickness not less than 50 microns) with perfortion not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts and nuts, etc. as required with 2 nos. 6 nos. G.I. wire as runing earthing. Make:- Legrand M/S SLOTCO/ STEELWAYS (Specification can be chagedas per present company's specification prior to permission form the Consultant

150 mm width x 50 mm depth x 1.6 mm thickness

300 mm width x 50 mm depth x 1.6 mm thickness

Supplyig and installing following size of Hot Dipped Galvanised Iron cable tray "Bends" (Galvanised not less than 50 microns) with perfortion not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts and nuts, etc. as required. Make:- Legrand M/S SLOTCO/ STEELWAYS

150 mm width x 50 mm depth x 1.6 mm thickness

300 mm width x 50 mm depth x 1.6 mm thickness

Supplyig and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (Galvanised not less than 50 microns) with perfortion not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts and nuts, etc. as required. Make:- Legrand M/S SLOTCO/ STEELWAYS

100 mm width x 50 mm depth x 1.6 mm thickness

300 mm width x 50 mm depth x 1.6 mm thickness

Supplyig and installing following size of Hot Dipped Galvanised Iron cable tray "Cross member" (Galvanised not less than 50 microns) with perfortion not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts and nuts, etc. as required. Make:- Legrand M/S SLOTCO/ STEELWAYS

100 mm width x 50 mm depth x 1.6 mm thickness

300 mm width x 50 mm depth x 1.6 mm thickness

Supplyig and installing following size of Hot Dipped Galvanised Iron cable tray "Reducer" (Galvanised not less than 50 microns) with perfortion not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts and nuts, etc. as required. Make:- Legrand M/S SLOTCO/ STEELWAYS

100 mm width x 50 mm depth x 1.6 mm thickness

300 mm width x 50 mm depth x 1.6 mm thickness

Laying and fixing of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1KV grade of following size on wall surface as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

1.1 KV Cable End Termination:-Supplying and making indoor cable end termination with brass double compression gland and aluminium lugs for following size of PVC insulated XLPE Al. Ar. Cable of 1.1 KV grade as required.

2 Core 10 Sq. mm. (19mm)

3.5 Core 25 Sq. mm. (28mm)

3.5 Core 35 Sq. mm. (35mm)

3.5 Core 95 Sq. mm. (45mm)

3.5 Core 150 Sq. mm. (50mm)

3.5 Core 300 Sq. mm. (70mm)

4 Core 10 Sq. mm. (25mm)

Supplying and making out door cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core XLPE aluminium conductor cable of 11 KV grade as required.

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc. as required

50 mm dia (DSR-2018)

80 mm dia (CSR-2018)

100 mm dia (DSR-2022)

Krone box:- (items From GeM) Providing, fixing, connecting & testing of Krone box (Telephone Tag Block) in a thermoplastic, IP 65 (weather proof) enclosure, internally embedded gasket, anti corrosive, insulated and shock proof with provision for cable through IP 65 glands complete in all respects. (Make : Matrix/Alcatel/Avaya. (COST FROM GeM)

10 pair Tag Block (krone Box) (136 mm x 253 mm x 115 mm)

20 pair Tag Block (krone Box) (136 mm x 253 mm x 115 mm)

50 pair Tag Block (krone Box) (300 mm x 300 mm x 70 mm)

Providing, laying, connecting, testing & commissioning of multi-core telephone unarmoured cables of conductor size 0.5 sq.mm. annealed tinned electrolitic grade copper, PVC insulated, twisted pairs bunched together, over all PVC sheathed, GI strip or wire armouring laid on existing cable tray or along the wall or laid in pipes or in trenches including excavation of cable trench, sand filling covering with bricks and back filling complete as required. (Make : Finolex / Polycab / Havells)

Cost of 10 pair TEL Cable (I Mtr.)

Cost of 20 pair Te. Cable (1 Mtr.)

Cost of 50 pair

Telephone Set Supply and installation of Digital Telephone Set with Caller ID system with connecting cord and jacks at user end. (Provision of ID Caller telephone for reception) Make:- (BEETEL/PANASONIC/ ORPAT).

IP PBX SYSTEM along Server Software and Unified Communication Server Software and Hot StandBy Server Software Pabx System-Epabx

Supply, fitting, fixing, commissioning and testing of IP based 100% non-blocking IP PABX System should be a IP Compatible with rich feature set of the system and can be connected with pure Voice over IP (VoIP) communication network across corporate Local and Wide Area Networks (LAN and WAN) as & when required. • IP PBX SYSTEM along Server Software and Unified Communication Server Software and Hot StandBy Server Software Pabx System-Epabx • Central Processing Unit: The system main software should be open architecture based. The CPU of main system shall be 32 bit processor working at 2.0 GHz or better. The system should be Wall mountable. • System Architecture should be latest pure IP and should be wall Mountable  Meet-me conference 30 party X 2 from day 1 must be available. Must Support Unified Communications Equipped with 64 Analog extensions 32 IP Extensions alongwith IP User License loaded from day expandable upto 256 IP Extensions, VOIP CARD in built charger, battery with one our back up facitity. 40 Analog Trunk Ports, 1 PRI , 02 Ports Auto Attendant- IPABX Make: Avaya/NEC/Alacatel

36 U (Floor Mounted)

Providing, fixing, fitting, installation and testing of 36 U Server Cabinet (RACK) (Floor Mounted) 19" LCS2 along with all following standard accessories:- (Make : Legrand-634806 / Schneider / Rittal/DATARACK

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Approx. Wt.120 Kg,

CRCA 'D' grade 1.6mm thick sheet, pwoder coated for cabinet RAL- 9002,

4mm Toughened Tinted Glass Door

Along with following accessories:-

1. Cooling fan 220/230V AC, of 90 CFM-------4 Nos.

2. Cable manager Metal 4 Nos.

3. PDU- 230V /AC 1 No.

4. Cable Channel 100mm wide. 2 Nos.

5. Heavy Duty Stationary Shelf 600mm(W)X475mm(D) -1 No.

6. Mounting Hardware (20 Sets of M-6 screws, washers, cage, nuts (Nickle Coated)- 3 Nos.

7. Earthing strips copper 150mm H 1 No.

8. Door Lock 1 No.

9. Caster Wheels (with breake) 2 Nos.

10. Caster Wheels (without breake) 2 Nos.

11. Front Metal Band 1 No.

Cost of 36 U Server Rack with GST

Active Components:-

L2 PoE Access Switch

Supply, fitting, fixing, connecting and testing of switch with 24 x 10/100/1000T PoE ports and 4 x 100/1000X SFP ports, Switching Capacity 56Gbps and Forwarding Rate 41.7Mpps, Switch should support PoE and PoE+ with 370W minimum power budget, operaating temperature 0°C to 50°C, Switch should support link reccovery within 50ms for Ring architecture, SDN or similar kind of technolgy should support, Warranty 5 year from Day 1 . Make:- Arista:- Product id: 5116877-68516599406Cisco - WS-C2960X-24PS-L / Allied Telesis - AT-x230-28GP / Juniper - EX2200-24P)

The above L2 Managed Data Switch consists of the following:-

1. Power cord India, right angle.

2. Both side Cable connector.

3. 1 year free service pack.

Interface- 24 x 10/100/1000T ports and 4 x 100/1000X SFP ports

Switching Capacity/Forwarding Rate :- 56Gbps/41.7Mpps

Performance:- Up to 16K MAC addresses, 256MB DDR SDRAM

Management:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN,

Security:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN,

Routing:- IPv4 static routing and RIP.

Fail-over:- Switch capable of recovery within 50ms in a ring for application high availability

IPv6:- Device management over IPv6 networks with SNMPv6, Telnetv6, SSHv6 and Syslogv6

Diagnostic:- Optical Digital Diagnostics Monitoring,Automatic link flap detection and port shutdown,Port and VLAN mirroring (RSPAN)

Standard Protocol:- IEEE 802.1Q,IEEE 802.1w,IEEE 802.1s,IEEE 802.1p,IEEE 802.1AB,IEEE 802.1AX,IEEE 802.3ad

Operating Temparature:- 0°C to 50°C

Certification:- EN,UL and RoHS

Warranty:- 5 Years.

Cost of L2 PoE Access Switch With GST

SITC of 2 MP Bullet Varifocal IP (IR) indoor Bullet camera (2.8-12mm Lens) (Matrix) , 3 years warranty, Day Night Type, -1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps,2.7 to 13.5 mm lens, 0.01 Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), Alarm: 2 inputs & 2 outputs, Audio: 1 input & 1 output, IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Scene change detection,Motion detection, Face detection, Audio exception detection, Video tampering, UL, FCC, CE certified. Make- Axis/Hikvision/Pelco/Honeywell or as appoved by Architect/ Consultant.

SITC of Matrix 2 MP IP Mini Dome indoor Camera with 3.6 fixed lens, Audio Support, 3 years warranty, Resolution D1 (704 x 480 Pixel),HD (1280 x 720 Pixel),Full HD (1920 x 1080 Pixel) Day Night type, ( Progressive Scan CMOS, 1920 × 1080 at 25fps,2.7 to 13.5 mm Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), Alarm: 2 inputs & 2 outputs, Audio: 1 input & 1 output, IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Scene change detection,Motion detection, Face detection, Audio exception detection, Video tampering, UL, FCC, CE certified. Make- Axis/Hikvision/Pelco/Honeywell or as appoved by Architect /Consultant.

SITC of 2MP IR Bullet Fixed Camera -1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8 mm Fixed lens, 0.01 Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Video tampering, UL, CE, FCC certified. Make- Axis/Hikvision/Pelco or as appoved by Architect/Consultant.

9 U WALL MOUNT EQUIPMENT RACK

SITC of of 9U Wall Mounted Equipment Cabinet 504.65X600X500 (HXWXD): Rack must be along with the following components like; Width (mm)-600, Depth (mm) - 500, Approx.Net Wt (kg) - 20, CRCA 'D' Grade thickness (mm) - 1.2, RAL 9017 (Matt Black), Glass - 4mm Toughened Tinted Glass Door, Accessories:, Cooling Fan (230V A/C 90 CFM) - 2 Nos, PDU 230VAC - 1 No, Cable Manager Metal- 2 Nos, Mounting Hardware (20 sets of M6 screws,washer,cage nuts (nickel coated)) - 1 No, Wall Screws (4 sets of 2'' screws, washer,rubber grommet (nickel coated)) - 1 No, Door Lock - 1 No, Front Metal Band -1 No. In the rack there must be maintained 1 U = 1.75 inches space. (Make : Make : Legrand-VALRACK/ Netrack/Rittal/Schneider/Ortronics or as approved by architect).

SITC of 43" LCD 24X7 Surveillance Monitor ). Make:- Sony, LG, Panasonic or as appoved by Architect/Consultant.

SITC of wall mount Tv 32 Inch LED Backlit LCD 32", Screen Size (Inches)32, Resolution (Pixels)(1366 x 768), HD Ready, Category:- Smart Type, Speakers: 12W x 2, Energy Star Rating in line with the Government of Indiia Notification number S O 1896(E) and S O 1897(E)NA, Warranty(Years)-3,

Ports & Connectivity:- Number of HDMI Ports 3 Number of USB Ports 2 Number of VGA Ports 0 Number of Ethernet Ports 1 Built-in Wi-fi Yes Wi-fi Direct Yes Remote Control,Connecting Cable,Batteries etc. BIS Registration as per CRS of Meity -Yes. Dimensions (Length x Breadth x Depth) (mm x mm x mm ) 739 x 472 x168. Dimensions may vary company to company. Make:-Make:- Sony, LG, Panasonic/Samsung or as appoved by Architect/ Consultant

Cost of Tv 32 Inch LED Backlit LCD

Supply, Fitting, fixing and testing of 3 Star Direct Cool Single Door Refrigerator IS:1476 latest for Direct Cool with following specifictions

Capacity: 80 Lit.

Power Consumption: 289 Kwh/Yhr

Power Requirement: 220 - 240 V, 50 Hz

Insulation: Puff

Eco-friendly refrigerant

Compressor Type: Power saver Compressor

Defrosting Type: Direct Cool

Type: Single Door

Built-in Stabilizer: Yes

Warranty: 1 Year

Make:-Videocon/Samsung/LG/ Haier/ Equivallent.

Supply, fitting, fixing, installation & testing of Water storage 15 Liters Geyser of BEE 5-star rating vertical type acralic rust free body, facility of temperature control ,with capillary themostat and thermal cut, ISI certified heating element along with inlet & outlet connecting pipe, fixing clamps, fasteners, cord, 16/20A 3 pin plug etc. as required. Make:- Venus / Bajaj / Havells/Recold.

Supply, fitting, fixing and testing of Microwave Oven 900 W 5 Star rating 23 L along with the microwave oven will automatically protect you in the offset of an accident and facilities with Timer, Preheat, Defrost, Reheat, Convection heating, Touch contol pannel, Adjustment of microwave power, Conformity to IndianStandard IS 11676, heatingchamber- Stainless steel, along with all accessories & 1 year warranty. Make:- Godrej-GMX 25CA1 MIZ/Samsung-CE1041DSB2/Haier/LG

Controller Based wall mount Indoor Wireless Access Point (Wi-Fi)

SITC OF Controller Based wall mount Indoor Wireless Access Point with following features:- 1. Antenna:- Internal Type. 2. Number Of Radios : Dual. 3. Frequency Band : 2.4 GHz & 5.0 GHz . 4. Supported Wi-fi Standards : 802.11ac Wave 2. 5. Wireless Speed Up to (Mbps) : 1800 . 6. Max Wireless Signal Range im Mts : 10 to 20 7. Channel Width (MHz) : 160 8. Maximum Data Rate MBps : 1800. 9. Supported Encryption : WPA2 AES. 10. Dedicated Console Port : Available. 11.Receiver Sensitivity in db - 65. 12. Transmit power (tx)(dBm) - 29 Radio Resource Management such for power channel,coverage hole detection and performance optimization : Available. Make:- Cisco, DLink, Ruckus.

Table Lamps- (Satinless Steel) SITC of Metal body Table lamp operating on 220V with 5 W LED lamp, have 1.5 mtr flexcible PVC cord and plug along with ON OFF Switch complete set. Material :- Metal, Weight:- 0.35 kilogram, Style:- Retro. Color: Silver, Table Mount Arrangement, .No.of LED Bulb:- 1 (5 W),Width:-33 cm, Length:- 33 cm, Height :- 33 cm

Automatic Electric Water Kettle SITC of 1.5 L of 1.5 KW/Operating voltage(Volt)230+/- 10% , Stainless Steel Automatic Electric Kettle complete set with cord . Indian standard for electric kettle Conforming to IS :367/1993 Latest. Warranty:- One Year.Make:- Prestige, Babaj, Philips.

RO WATER PURIFICATION SYSTEM Supply , fitting fixing and commissioning of INDIAN WATER INC. PURE WATERFOR LIFE Fully automatic with autocut off RO Potable WaterPuri 2000 Plus 25 Litre RO+UV+UF Water Purifier Electrically oparated • Purification Technology RO+UV+UF • Capacity 25 Litre • Filter - Pre-filter (optional), sediment filter, activated carbon filter, anti-scalant filter, post-UF filter, • Membrane Type, 80 GPD, • Power Features- • Power Requirement- 110V - 300V, 50 Hz, • Operating Voltage - 24V DC V along with all required accessories, like, connecting wires, pipes, stand and fixing euipments along with drain Pipe in put pipe and etc as required. Make- Aquagard, Voltas, Kent.

Supplying, fitting, fixing, connecting and testing of CAT6 UTP RJ45 Loaded patch panel & connector - 24 port loaded 19" panel - 1 U, Panel: DC01 galvanised sheet steel, Compliant with standards: ISO/IEC 11801 Edition 3.0 CENELEC EN 50173-1 2007 ANSI/EIA/TIA 568 C2-1 IEC series 60603-7, NFC 20730, Standard 8877 – 603.7, Contacts: gold/nickel, thickness of gold > 0.8 μm minimum, Equipped with rear cable guide to hold cable during maintenance,The connectors are connected from the front without a special tool. Equipped with 4 cassettes of 6 RJ45 Cat. 6 connectors with toolless fast connection, marked 568 A/B, Max. number of connections and disconnections: 5 without replacing the wire, Endurance: 2500 operations (plug-in/pull-out) IK03, Operating temperature: -40°C to +70°C (Make:- Make :- Legrand- 632791, 076588/ Amps./ Schneider.

24 Port LIU:- Supply, Installtion & Commisioning of LIU 24 Core MM SC Fully Loaded along with all accessories. Make :- Legrand/ Amps/RIT/ Schneider

Providing, fixing, connecting & testing of Blanking plate (6XRJ45 Blanking plate for 19" panel - Black). .(Make : Legrand-032129 AMP/ Schneider)

Providing, fixing, fitting, connecting and testing of Splice Tray - 24 Fiber Capacity. :(Make : Legrand - 032130/ Schneider/ AMP)

Fiber Patch Cord:- SITC of SC/SC or SC LC Duplex 2 Mtr MM Fiber Patch Chord as per requirement. Make :- Legrand/ Amps/RIT/ Schneider

10/100/1000 MM SFP Module:- Providing, fixing, connecting & testing of Gigabit Fiber Module-MM, Support up to 550mtr (Make:- Cisco - GLC-SX-MMD / Allied Telesis -Model No. GLC-SX-MMD/AT-SPSX/CTP-SFP-1GE-SX) / Juniper - CTP-SFP-1GE-SX)/Equivalent in HP.

TV ACCESSORIES Supply, fitting, fixing and testing of Auto-manual Voltage Stabilizer with High Voltage cut off 0.25 KV 220V Range- 100 to 280V Single Phase 50 Hz Stabilizer along with cord & plug. Make:- Sen & Pandit, V Guard, Neutronix.

Accessories for TV SYSTEM Supply, erection, testing and commissioning of splitter / tap off mounted in suitable sizes MS boxes for MATV system and shall be suitable for interactive system. Make:- (Reputed of as directed by I/E or Consultant)

Two Way (S-2) (Make:- Reputed of as directed by I/E or Consultant)

Four Way (S-4) (Make:- Reputed of as directed by I/E or Consultant)

Two way tap off (T2) (Make:- Reputed of as directed by I/E or Consultant)

Four way tap off (T4) (Make:- Reputed of as directed by I/E or Consultant)

SITC OF IP Setup Box. (Reputed of as directed by I/E or Consultant)

Supplying, fitting, fixing, connecting and testing of decorative Wall Bracket Fixtures in nchrome finish in glass diffuser with 2x10Watt LED lamp directly on wall including connection with 1.5 sq mm FR PVC insulated copper conductor cable and eathing the body etc. as required. Make:- Philips, Bajaj, Havells.

SITC of 25A to 32A, 2 module DP Switch with Insert KEY card switch (Key Card Switch) set along with all rrquired accessoreis and plate with card for oparating ON OFF of Elec. Switch board of Guest Room. Make:- Schneider/Legrand or reputed.

MAIN LT PANEL FLOOR MOUNT FOR HOTEL BUILDING (Location in Basement Floor Electric Room)

Supplying, designing, manufacturing, installation, shifting to location, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing feeders of Wall/Floor Mount LT Panel, fabricated out of 2mm thick (14SWG) CRCA sheet steel, dust and vermin proof with reinforcement of suitable size iron channel, size 25mm x 25mm x 3mm with proper lifting arrangement, (IP-42) fully compartmentalized cubical type (folded joints construction), totally enclosed LT Panel and suitable for use on 415V, 3 phase, AC Supply, 4 wire, 50 C/S, system having 36 KA fault capacity, housed with incoming and outgoing aluminum bus bars, interconnection, interlocking between feeders etc. with indicating lamps, push buttons, necessary accessories, all out going feeders protection & meters as required.

The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs.

Main LT Panel shall have 20% spare outgoing feeders for different rating of feeders. The Panels shall be preferably arranged in multitier formation. The size of the panel shall be designed in such a way that the internal space is sufficient for hot air movement, and the electrical component do not attain temperature rise more than 40 degree Celsius.

The LT Panel shall be totally enclosed, completely dust and vermin proof. Synthetic rubber gaskets (neoprene/DPDM) between all adjacent units and beneath all covers shall be provided to render the joints dust proof. All doors and covers shall be fully gasketed and shall be lockable. Doors shall have concealed hinges. All the doors shall be suitably reinforced by channel to provide rigidity. Panel shall have suitable cable entry from bottom and suitable arrangement for aluminum cable termination.

The panel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions. A 6/16A socket with sitch as service outlet (single phase) and 1 no. 10W LED LAMP with holder shall be provided in one of the compartments as service outlet in the panel. The complete panel shall be fuse less type, for control circuits 2A SP MCB's to be used.

Panel Builder will provide shop drawing SLD & GA drawing along with BOM with CAT. No. of each and every components and switch gears of LT Panel for approval of Consultant. Panel Builder shall visit the site before manufacturing the Panel. Inspection of the Panel shall be carried out at Panel Builder's factory by the Consultant before final delivery for that all arrangements shall be made by the contractor.

Location :- Location in Basement Floor Electric Room.

The Name Plate for each feeder must be in Anodized Aluminium Sheet.

Make of MCCB - L&T D-Sine/ Legrand DPX³ / Schneider-NSX / Siemens - 3VL.

Make of MCB - (10kA-C-Series.) L&T U Version/ Legrand-Dx³/ Schneider-Acti / Siemens.-Bita Guard

Make of On Load Change Over :- L&T , Sucomo, Legrand.

Size of incoming cable:- 2R 3.5C 300 Sq.mm. Al. Ar. Cable.

Panel Size - As per approved Drawing.

All 4 pole MCCB with thermomagnetic based release must have follwing characterstics:-

1. Icu=100% Ics.

2. With positive Isolation Marked.

3. With adjustable short circuit and over load.

4. As per IEC 60947-2.

AL. BUS BAR

The panel includes 415V, 800A, 3Ph, 36KA, 50Hz, TPN Electrolytic Aluminium Bus Bar (E91E) GI Earth Bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. The electrolytic Aluminium bus bar as per I:S 5082 of suitable length and insulated by heat shrinkable sleeves Red, yellow, Blue and Black as R Y B & N. The current density of bus bar shall be minimum 0.8 A / sq mm. Minimum clearance between live parts / neutral to earth shall be 19mm. However clearances between terminals at components shall be as per applicable individual standard for components. Interconnections between the main bus bars and individual units shall be made using vertical / horizontal Bus Bar to individual MCB shall be made with 4, 6 & 10 Sq mm FRLS PVC Cu. wire with 63A 4 studs (Brass) treminal block, aluminium bus bars of adequate rating. AL. Bus Bar will be supported on insulators made of non-hygroscopic, non-inflammable material with tracking index equal to or more than that defined in BIS.

Bill of Material of Main LT PANEL:-

1 Set Of Fabrication part of LT Panel & busbar system, in CRCA Sheet Steel enclosure (IP-42) without any components & its busbar system, in CRCA Sheet Steel enclosure without any components. Name of Panel Builder :- JMD ELECTROTECH, KOKAR, STECT POWER INDUSTRIES, BIT, Mesra, Arnav Power Tech, Ranchi, TTS Systematix Private Ltd, Tatisiway, Meditron, Meshra, Ranchi or any approved Panel Builders of above make Switch Gears.

INDICATING

1 Set Multifunction Meter having (5010 Series) LED mete display accuracy Class 1 as per IEC 62053-21, should have an active RS-485 port, in built RTC, Aux Supply: 44-277Vac/dc. Parameters: Volts, Amps, PF, THD, F, W, Wh, VA, VAh, Var, Varh, Runhrs, Onhrs Interrupts, THD for V&I per phase, individual harmonics for V&I upto 15th level complying with IEC61557-12. Min/Max for eight parameters. Sampling rate: 64 samples per cycle.

3 Sets Phase indicating light shall be protected by 2 Amps SP MCB's for incomer & outgoing.

3 nos. CT of appropriate power as per incomer /5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix/Rishabh.

INCOMER :-

1 No.630 A F/P MCCB (36kA) with adjustable thermomagnetc release type with S/C & O/L protection, With ON-OFF- Indication and front extended rotary Handle and spreader links in both end (Incoming cable size –2 Run 630 Sq mm 3.5 Core Al. Ar. Cable).

Out Going Feeders Without DG Set

1 No. 160 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. ( For APFC Panel) Cable Size 3.5 C 95 Sq.mm Al,Azr, Cable)

11 Nos. 63 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. (8 nos. for Power DB & 1 no. For Goods Lift, 1 no. For external lighting & 1 no. As spare)

2 Nos. 25 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. (2 Nos. as spare )

Out Going Feeders With DG Set

Provision of Mechnical interlocking between 250A/FP/25KA MCCB as common incoming and 1 No. of 250A on load Change over for D.G incomer, in such a way so that the two supplies are not parallel at any time.

1 No. 250A TPN on load Manual Change over panel mounted open execution type and suitable bus arrangement for Cable termination. Make-L&T/Sucomo/ Legrand.

1 No. 250A/FP/25KA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links.

6 Nos. 63 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. (2 nos. for Power DB of GR. Fl & 2 no. For Passenger's Lift, 1 no. For UPS, 1 no. For Fire Fighting Panel & 1 no. As spare)

8 Nos. 25 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. (6 Nos. For LDB & 2 nos. as spare )

4 nos. 32 A DP MCB C Seires 10kA (2 nos. for Submersible pum Motor & 2 nos. as spare)

Total Cost of Main LT Panel

A.P.F.C. Panel (Capacitor Bank) Auto Mannual Type

A.P.F.C. Panel (Capacitor Bank) Auto Mannual Type (APFC) Panel – 115 KVAR 8 Stage Capacitor Bank Details with mixed dielectric Ultra Heavy Duty Capacitors of following range and 1 Set 15 KVAR (2x7.5 KVAR) fixed Capacitor bank to take care of no load losses of Transformer :-

Supplying, designing and manufacturing in correct alignment position, un loading at site, shifting to location, effecting proper connection of all incomer and outgoing of A.P.F.C. Panel (Capacitor Bank / Auto Mannual), testing of the same made of 2 mm CRCA sheet (14 SWG) steel IP –42 floor mounting dust and vermin proof cubical type Capacitor Bank Panel suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 50kA with front operated construction including separate fabrication arrangement for fixing MCCB, , M.C.B., Capacitors, Contactors etc.

The 2 mm sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized with locking arrangement duly fixed on Base Channel with proper lifting arrangement size – 50 mm x 50 mm x 4 mm having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs and Capacitors having earthing arrangement.

All openings shall be covered by soft rubber gasket, enclosure shall be galvanized.

Aluminum Bus Bar for Panel :-

Bus bar shall be suitable for 250A, TPN busbar chamber of suitable length with (E91EWP) Eletrolytic Aluminum busbars. All busbars and interconnections shall be of suitable size Aluminum busbar, current density of Aluminum shall not be more than 0.8 Amps/sq.mm cross sectional area of Bus Bar with removel gland plates, cable glands, at sending and receiving ends, encluding connections with outgoing feeders complete in all respect and all interconnections shall be made with 2.5, 4 and 6 sq.mm. PVC Cu.wire. The Aluminium bus bar shall be with heat shrinkable PVC Slived Red,Yellow,Blue & Black as (RYB & N ) after temperature and incloser derating maximum allowable temp.of bus bar shall be 90 degree C

Panel Size - As per Drawing and shall be provided at the time of work order.

Panel Builder will provide shop drawing SLD & GA drawing along with BOM with CAT. No. of each and every components and switch gears of APFC Panel for approval of Consultant. Panel Builder shall visit the site before manufacturing the Panel. Inspection of the Panel shall be carried out at Panel Builder's factory by the Consultant before final delivery for that all arrangements shall be made by the panel Builder.

The Name Plate for each feeder must be in Anodized Aluminium Sheet.

The Panel Builder must be CPRI approved. Panel builder must produce test certificate for Type Tested & Short Ckt withstand capacity as per IEC-60439-II from CPRI.

1 Set Of Fabrication part of LT Panel & busbar system, in CRCA Sheet Steel enclosure (IP-42) without any components & its busbar system, in CRCA Sheet Steel enclosure without any components. Name of Panel Builder :- JMD ELECTROTECH, KOKAR, STECT POWER INDUSTRIES, BIT, Mesra, Arnav Power Tech. Ranchi, TTS Systematix Private Ltd, Tatisiway, Meditron, Meshra, Ranchi or any approved Panel Builders of above make Switch Gears.

Location : Panel Room.

Make of MCCB - L&T D-Sine/ Legrand DPX³ / Schneider-NSX / Siemens - 3VL.

Make of MCB - (10kA-C-Series.) L&T U Version/ Legrand-Dx³/ Schneider-Acti / Siemens.-Bita Guard

Location :- Location in Basement Floor Electric Room.

The Name Plate for each feeder must be in Anodized Aluminium Sheet.

Panel Size - As per approved Drawing.

Bill of Material in A.P.F.C.R. Panel :-

2 Nos. 63A TP / MCB / 10kA (D tripping characteristic) for 25 KVAR Capacitor.

2 Nos. 40A TP / MCB / 10kA (D tripping characteristic) for 20 KVAR Capacitor.

2 Nos. 16A TP / MCB / 10kA (D tripping characteristic) for 7.5 KVAR Capacitor.

2 Nos. 10A TP / MCB / 10kA (D tripping characteristic) for 5 KVAR Capacitor.

Incomer

1 No. 160 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. ( For APFC Panel) Cable Size 3.5 C 95 Sq.mm Al,Azr, Cable)

Indication:-

16 Nos. LED Indicators sets (220V) (R – 8/ G – 8 = 16 Nos.) self illuminated Red-Green (ON-OFF) push buttons, each backed up with Push Button (Red- Yellow) shall be provided for each capacitor unit to indicate the status of the unit. Make-L& T./ AE/ Rishabh.

3 Nos. LED indicatore (R Y-& B) of 220V. with 2A SP MCB protection. Make- Legrand / L&T / Rishabh )

3 Set CT 200/5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix / L&T

3 Nos. 16A – 2 pole / 2 way Rotary Switch. Make:- Reputed

8 Nos. 10A Toggle Switch SP – HT Make:- Reputed

1 Set Power factor correction Intelligent controller Relay with 8 steps and multi -functional display, APFCR with 8 steps. The relay shall be sensitive to pick up 1% of rated current and correct the P.F accordingly. Also the relay shall display the harmonic level of system. Make- L&T, Seimens.

1 Set VAF + Power Factor, 3Ph, Class 1, 5A, Meter Make- L&T / Seimens / Scheneider.

The capacitors for Auto Mannual Type (APFC) Panel – 115 KVAR 8 Stage Capacitor Bank Details with following parameters:- (BOX SERIES OF 440V)

1. MPPXL ,440V/50Hz,TP Shunt mixed dielectric heavy duty Capacitor.

2 Lower operating losses - 0.35W/KVAr).

3. Over current withstand capability - 1.8 times rated current.

4. Inrush current withstand capability - 300 times rated current.

5. Operating Life- 130000 hours.

6. Numbering of switching- 8000 operations per year.

7. Insulation Class H.

Mixed dielectric Ultra Heavy Duty Power Resin filled Capacitor Make:- Legrand/ L&T / Schneider -Meher

2 Nos. 25 KVAR (Power Capacitor) Ultra Heavy Duty.

2 Nos. 20 KVAR (Power Capacitor) Ultra Heavy Duty.

2 Nos. 7.5 KVAR (Power Capacitor) Ultra Heavy Duty.

2 Nos. 5 KVAR (Power Capacitor) Ultra Heavy Duty.

Total - 115 KVAR.

Capacitor Duty Contactors :- (NO/NC) Make:-Seimens / L&T.

2 Nos. For 25 KVAR – MOC 25 1NO & 1 NC (63A) (Suitable for 25 KVAR capacitor bank).

2 Nos. For 20 KVAR – MOC 20 1NO & 1 NC (40A) (Suitable for 20 KVAR capacitor bank).

2 Nos. For 7.5 KVAR – MOC 15 1NO & 1 NC (16A) (Suitable for 7.5 KVAR capacitor bank).

2 Nos. For 5 KVAR – MOC 15 1NO & 1 NC (10A) (Suitable for 5 KVAR capacitor bank).

2 Sets (7.5 x 2) = 15 KVAR fixed Capacitor Bank with all required accessories like capacitor duty contactor (For each 7.5 KVAR –MOC 8.5 1NO & 1 NC (16A),) each capacitor shall with 16A TP / MCB / 10kA (D tripping characteristic) R & Y indicators, toggle switch etc. shall be fixed capacitor to take care of the no load losses of the transformer. (1 Set)

Total Cost of APFCR Panel with 15 KVAR (7.5 x 2) as Fixed Capacitor Bank.

Out Door External Lighting Panel (Feeder Pillar) :-

Supply, manufacturing and effecting proper connection of all incomer and outgoing, unloading at site, shifting tolocation, fitting, fixing and testing of the of out door canopy type double door Feeder Pillar fabricated out 2 mm (14 SWG) CRCA Sheet steel dust, damp, vermin and water proof (IP-55) free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted (powder coated) complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required.

The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs.

The LT Panel shall be totally enclosed, completely dust and vermin proof. Synthetic rubber gaskets (neoprene/DPDM) between all adjacent units and beneath all covers shall be provided to render the joints dust proof. All doors and covers shall be fully gasketed and shall be lockable. Doors shall have concealed hinges. All the doors shall be suitably reinforced by channel to provide rigidity. Panel shall have suitable cable entry from bottom and suitable arrangement for aluminum cable termination.

The panel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions. A 6/16A socket with sitch as service outlet (single phase) and 1 no. 10W LED LAMP with holder shall be provided in one of the compartments as service outlet in the panel. The complete panel shall be fuse less type, for control circuits 2A SP MCB's to be used.

The panel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions. A 6/16A socket with sitch as service outlet (single phase) and 1 no. 10W LED LAMP with holder shall be provided in one of the compartments as service outlet in the panel. The complete panel shall be fuse less type, for control circuits 2A SP MCB's to be used.

Panel Builder will provide shop drawing SLD & GA drawing along with BOM with CAT. No. of each and every components and switch gears of LT Panel for approval of Consultant. Panel Builder shall visit the site before manufacturing the Panel. Inspection of the Panel shall be carried out at Panel Builder's factory by the Consultant before final delivery for that all arrangements shall be made by the contractor.

Location :- Location in Basement Floor Electric Room.

The Name Plate for each feeder must be in Anodized Aluminium Sheet.

Make of MCCB - L&T D-Sine/ Legrand DPX³ / Schneider-NSX / Siemens - 3VL.

Make of MCB - (10kA-C-Series.) L&T U Version/ Legrand-Dx³/ Schneider-Acti / Siemens.-Bita Guard

Make of Modular Change Over :- L&T , Schneider, Legrand.

Panel Size - As per approved Drawing.

All 4 pole MCCB with thermomagnetic based release must have follwing characterstics:-

1. Icu=100% Ics.

2. With positive Isolation Marked.

3. With adjustable short circuit and over load.

4. As per IEC 60947-2.

AL. BUS BAR

The panel includes 415V, 100A, 3Ph, 36KA, 50Hz, TPN Electrolytic Aluminium Bus Bar (E91E) GI Earth Bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. The electrolytic Aluminium bus bar as per I:S 5082 of suitable length and insulated by heat shrinkable sleeves Red, yellow, Blue and Black as R Y B & N. The current density of bus bar shall be minimum 0.8 A / sq mm. Minimum clearance between live parts / neutral to earth shall be 19mm. However clearances between terminals at components shall be as per applicable individual standard for components. Interconnections between the main bus bars and individual units shall be made using vertical / horizontal Bus Bar to individual MCB shall be made with 1.5, 2.5 Sq mm FRLS PVC Cu. wire with 63A 4 studs (Brass) treminal block, aluminium bus bars of adequate rating. AL. Bus Bar will be supported on insulators made of non-hygroscopic, non-inflammable material with tracking index equal to or more than that defined in BIS.

Bill of Material of Main LT PANEL:-

1 Set Of Fabrication part of LT Panel & busbar system, in CRCA Sheet Steel enclosure (IP-42) without any components & its busbar system, in CRCA Sheet Steel enclosure without any components. Name of Panel Builder :- JMD ELECTROTECH, KOKAR, STECT POWER INDUSTRIES, BIT, Mesra, Arnav Power Tech, Ranchi, TTS Systematix Private Ltd, Tatisiway, Meditron, Meshra, Ranchi or any approved Panel Builders of above make Switch Gears.

INDICATING

1 Set Multifunction Meter having (5010 Series) LED mete display accuracy Class 1 as per IEC 62053-21, should have an active RS-485 port, in built RTC, Aux Supply: 44-277Vac/dc. Parameters: Volts, Amps, PF, THD, F, W, Wh, VA, VAh, Var, Varh, Runhrs, Onhrs Interrupts, THD for V&I per phase, individual harmonics for V&I upto 15th level complying with IEC61557-12. Min/Max for eight parameters. Sampling rate: 64 samples per cycle.

3 Sets Phase indicating light shall be protected by 2 Amps SP MCB's for incomer & outgoing.

3 nos. CT of appropriate power as per incomer /5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix/Rishabh.

INCOMER :-

1 No.63A F/P MCCB (25kA) with adjustable thermomagnetc release type with S/C & O/L protection, and front extended rotary Handle and spreader links in both end.

OUT GOING

OUT- GOING

3 nos. 25A/FP/25KA/ MCCB thermomagnetic release type, on of trip and S/C , O/L protection, with Rotary Handle & Spreader links.

2 nos. Power Contactor 40A NO NC of three phase of suitable rating.

2 nos. Astronomical Alpha Rex³ single channel Timer 24 hrs.

2 nos. Four pole two way Lexic changeover with centre off 440V AC 40A to be used in case of timer failure to by pass the timer.

2 nos. 63A DP MCB C Series of 10 kA

2 nos. 32A DP MCB C Series of 10 kA

Total Cost of External Feeder Pillar Panel

Supply fitting and fixing of PVC/XLPE insulated PVC H.T Cable (11 KV Grade) for working voltage up to and including1100 Volts confirming to IS 1554 (part-1) , 3 Core 95 Sq. mm 11 KV grade, armoured power H.T Cable. Make:- Havells, KEI, Fort Gloster, Finolex.

SITC OF 10 C control Cable 2.5 Copper Armoured Cable of grade 650V to 1.1 KV. Make:- Havells, KEI, Fort Gloster, Finolex

Supplying & Laying 12mm thick chequered rubber matting of 1.1.kv 1 m wide of tested quality to with stand 15KV dielectric strenght of approved make as per IS-5424-1969.

Supplying of fire buckets of 10 liters Capacity of approved quality, painted white from inside and red outside and having inscription "FIRE" in white conforming to I.S. 2546/1974 duly amended upto date complete as required & approved by Engineer Incharge.

Supplying and fixing of MS pedestal stand heavy duty with rain protection cover as required suitable for supporting three fire buckets as required for fire fighting system & approved by Engineer Incharge.

Supplying and fixing carbon dioxide (CO2) type fire extinguishers conforming to IS 15683 with cylinder duly charged of capacity 4.5kgs. including fixing clamps, brackets, bolts and nuts etc. as required & approved by the Engineer Incharge.

Supplying and fixing 10kg capacity Modular Automatic Fire Extinguishers dry chemical powder nitrogen type pre-set at works ranging from 57 deg C/ 68 deg C/ 79 deg C fire extinguishers conforming to IS 15683 including fixing clamps, brackets, bolts and nuts etc. complete as required & approved by the Engineer Incharge.

Supply and fixing of shock treatment/ restoration charts written in Hindi/ local language and English duly framed and covered with 3.0 mm glass as required.

Supply of First Aid Box made of 16 SWG MS Sheet duly painted within inside and outside surfaces with one coat of primer and two coats of synthetic paint of required shade comprising the following minimum but not limited, minimum 1 No. band aid bandage 150mm, 1 No. Savlon Soap 30 ml, 1 No bottle Betadine 30 ml, 1 No Packet dressing material etc. as required, approved by Indian Red Cross / St. John's conforming to IS:2217.

Supply of 440V grade Rubber Hands Gloves. As per IS:4770- 1991.

Supply of 1 pair 12 KV rubber hand gloves of approved make, as per IS:4770- 1991.

Supplying & fixing of fire sealants to shafts, ceiling, cut-outs etc. with 2 hour fire rated composition as per specifications, NEC2011, relevant IS & as per approved makes of material & making good the same complete with accessories as required per site

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

Supply and fixing position the approved single line diagram framed in 1000 x 800 mm size glass frame and installed in main switch room.

Providing, fitting, fixing, fabricating, erecting of MS angle/Channel of section 50 mm x 50 mm x 6 mm size for Brick wall trench to make support for MS iron plate to be fixed on every after 300 mm in RCC trench.

Providing, fitting, fixing, fabricating, erecting of MS Plate of 2'X2 (12 mm) thick' for covering Brick wall cable trench in panel room on the support of iron angle each piece of MS plate shall be 450 mm (D) x 450 mm (W). (To cover the Brick wall cable trench in panel room.)

200 KVA Copper Wound Distribution OCTC Transformer as per IS-1180 (Level-1)

Supplying, installation, shifting to location, testing and commissioning of a continuous rating of 200 KVA, 3Ph, 50Cy, 11/0.433KV, Off Circuit, (OCTC) oil cooled, copper wound, (-12.5% to +2.5% in step of 2.5 %) Outdoor Transformer as per IS 1180 (Level-1) at full load and temp. rise not exceeding 45 degree C, by Thermometer in oil and 50 Degree C. by the resistance in winding after continuous run in full load rating. The Transformer should oil immersed winding having Vector DY-11 HT side connected in Delta, & LT Side connected in Star with neutral brought out connected to provide separate earthing. In Transformer HT Side Cable End Box, & LT side - Cable End Box. Transformer shall be latest manufacturing standards as per amended IS Specifications and load and no load losses shall be limited to the values given below as per IS or Norms issued by JVVNL or which ever is lower. The transformer, length of MS channels as per the norms of 200 KVA Outdoor Transformer with all accessories, air filled cable box and accessories as per General Specifications of 200KVA out Door Transformer and should have suitable for 11KV 1 Run, 3 Core 95 Sq mm XLPE Al. Ar. Cable and LV termination box shall have suitable arrangement for 1.1 KV, 2 Run, 3.5 Core, 300 Sq. mm XLPE Al. Ar. Cable etc as required. The copper loss and Iron loss shall be as per the Level 1 rating out Door Transformer. The Transformer shall have all standard Protection, standard accessories etc and shall have 3 Years warranty against any manufacturing defect from the date of delivery under normal operating conditions and proper use (Make:- Power Star/True Volt/ Synergy, Arnav Power Tech.)

Total Cost of 200 KVA Oil Cooled copper wound out Door Transfomer Level-1mas per IS- 1180.

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required :

Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.

Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.

M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.

Suitable cement concrete foundation duly plastered with anti vibration pads.

1620 lpm at 56 m Head

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump)

Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.

Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required.

M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required.

Suitable cement concrete foundation duly plastered and with anti vibration pads.

1620 lpm at 56 m Head

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump)

Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520.

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325.

M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.

Suitable cement concrete foundation duly plastered and with anti vibration pads.

180 lpm at 56 m Head

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)

Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.

M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.

Suitable cement concrete foundation duly plastered and with anti vibration pads.

450 lpm at 35 m Head

Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, inter- connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :

INCOMING

250A, 50kA 4 Pole MCCB, Ics=100% Icu rating

LED type RYB phase indicating lamps, ON, OFF, trip indicating lamps

Set of Copper Bus Bar 300A

OUTGOING

Main Fire Pump

Jockey Pump

DIESEL ENGINE CONTROL

Control for diesel engine comprising -

Automatic/Manual selctor switch & 3 attempts starting device, timers and relays as required, push buttons, start/stop in manual mode

Indicating lamp for high/ Low Lub. Oil pressure, High Water Temp and Engine on indication

All standard relays and accessories for automatic operation of diesel engine System Controller

Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specification

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42.

For Terrace Pump

Supply of PVC/XLPE Insulated PVC sheathed , heavy duty armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts (Conforms to IS:1554,part-1)

3½ CORE ARMOURED 50 Sq.mm

4 CORE ARMOURED 10 Sq.mm.

4 CORE ARMOURED 16 Sq.mm.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3 × 10 sq.mm.(aluminium)

3 X 16 sq. mm (25mm)

3 X 16 sq. mm (25mm)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Up to 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and up to 95 sq. mm (clamped with 25x3mm MS flat clamp)

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

200 mm dia (wall thickness 6.3 mm)

250 mm dia (wall thickness 6.3 mm)

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 250mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

65mm dia

100mm dia

150mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

80 mm dia

100mm dia

150mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required.

20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585

20 mm nominal internal dia gun metal globe valve & nozzle.

Drum and brackets for fixing the equipmets on wall.

Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

Stainless Steel (Grade 304)

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

2 way-100 mm dia M.S. Pipe

4 way - 150 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :

Pendent Sprinkler

Horizontal side wall sprinkler

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 100mm dia

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required : 100mm dia

Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect.

Providing , fixing Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (4 Kg Capacity)

Carbon Di-oxide Type , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for ‘B’ ‘C’ Class of FIRE (4.5 Kg Capacity)

Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)

Air release Valve / Drain Valve

MS Structure support for piping

Providing and fixing 25 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end)

Two Loop Panel

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required

Supplying, installation, testing & commissioning of fire fighter phone jack complete as required

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Supply, installation,testing and commissioning of EXIT light, self contained 10W luminaire complete with flush mounting MS frame ,sign label,NiCad battery

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required-3W

Supplying, installation, testing & commissioning of digital audio amplifier 50 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required.

speaker cable Single pair, 2-core, 1.5 sqmm

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

Supplying and placing of King Size Bed made of Prelaminated particle board in walnut finish, hydraulic storage bed, Bed size 2034 mm(L) x 2500 mm(D) x 1050 mm(H). The product must be from a manufacturer having ISO 9001, ISO 14001 , AIOTA , BIFMA COMPLIANT, GREEN GUARD, SEDEX Certificate. (Make - Durian/ Equivalent, Model no. - PIPER-KB).

Supply and installation of 2 door wardrobe. The Interchangeable Shelf System For Varying Heights. The Product Dimension : (W)800mm X (D)500mm X (H)2000mm,The product must be from a manufacturer having ISO 9001,ISO14001 ,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX Certificate. (Make - Durian/ Equivalent, Model No.- Robinson/Wd-2)

Supplying and placing robinson Nightstand Bedside unit. The Unit In A Single Finish That Matches The Bed Frame With Contrasting Handles For The Drawers. The Open Shelf Below Allows For Storing Your Books And Magazines. Product Dimension :(W)500mm X (D)400mm X (H)450mm. The product must be from a manufacturer having ISO 9001,ISO14001 ,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX CERTIFICATE. (Make - Durian/ Equivalent, MODEL NO.- Robinson/WD-2)

Supplying and placing of Coffee Set. The Brighton set comprises of a cafe style coffee table with two matching chairs. A warm walnut finish with solid wood construction the table sits sung on its three legs with a gorgeous central pillar base. The chairs come with the same finish and have soft fabric upholstered cushions along with slender side bolsters and a curved back that flows from the left to the right. Product Dimension : (W)1650mm X (D)965mm X (H)940mm. The product must be from a manufacturer having ISO 9001, ISO14001, AIOTA, BIFMA COMPLIANT, GREEN GUARD,SEDEX Certificate. (Make - Durian/ Equivalent, MODEL NO. : ROBINSON/WD-2)

Supplying and placing of Cafe table sets(1+6).The Rectangular Dining Table Has A Polished Veneer Top And Solid Wood Construction Finished In Rosewood. Product Dimension :(W)1500mm X (D)900mm X (H)760mm. Cafe Chair-Amelia Dining Chair. The Cushioned Seat In Burgundy Leatherette Upholstery. Product Dimension :(W)515mm X (D)500mm X (H)760mm, The product must be from a manufacturer having ISO 9001,ISO14001 , AIOTA, BIFMA Compliant, GREEN GUARD,SEDEX CERTIFICATE. (Make - Durian/ Equivalent, Model - Arabian+amelia)

Supplying and placing of Cafe table sets(1+4).The Rectangular Dining Table Has A Polished Veneer Top And Solid Wood Construction Finished In Rosewood. Product Dimension :(W)1150mm X (D)750mm X (H)760mm. Cafe Chair-Amelia Dining Chair. The Cushioned Seat In Burgundy Leatherette Upholstery. Product Dimension :(W)515mm X (D)500mm X (H)760mm, The product must be from a manufacturer having ISO 9001,ISO14001 , AIOTA, BIFMA Compliant, GREEN GUARD,SEDEX CERTIFICATE. (Make - Durian/ Equivalent, Model - Arabian+amelia)

SUPPLYING AND PLACING OF OFFICE TABLE, MADE OF PRELAMINATED PARTICLE BOARD IN WHITE/GREY-MAPLE/DARK GREY COLOR WITH MAIN TABLE SIZE 1500MM(L)X 600MM(D)X 750MM(H) WITH SIDE UNIT OF SIZE : 900MM(L)X 450MM(D)X 750MM(H). , THE PRODUCT MUST BE FROM A MANUFACTURER HAVING ISO 9001,ISO 14001 ,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX,SEFA CERTIFICATE. (Make - Durian/ Equivalent, MODEL NO: DWS/34723)

Supplying and placing of Medium Back Chair, Size: (W)585mm X (D)660mm X (H)1060mm • Mesh back with Adjustable Lumbar Support. • Fabric Upholstered seat with Moulded Foam. • Synchro Single Locking Mechanism. • Fix Armrest • Nylon Base with Smooth Nylon Castor. THE PRODUCT MUST BE FROM A MANUFACTURER HAVING ISO 9001,ISO 14001 ,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX,SEFA CERTIFICATE. (Make - Durian/ Equivalent, MODEL NO:- DEFINE/MB/STANDARD)

Supplying and placing of Office Visitor Chair Description The Pushback Single Locking Mechanism, Pneumatic Height Adjustment, And Tilt Tension Control Knob Provide An Ultimate Ergonomic Experience. The Solid Nylon Base Supports The Structure While 55Mm Castor Wheels Provide Easy Movement. An Ideal Chair, Experience Magic Every Day With The Magic Office Chair. Product Dimension : (W)560mm X (D)660mm X (H)1000mm. THE PRODUCT MUST BE FROM A MANUFACTURER HAVING ISO 9001,ISO 14001 ,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX,SEFA CERTIFICATE. (Make - Durian/ Equivalent, MODEL NO:-MMPL/70020)

SUPPLYING AND PLACING OF GLASS DOOR STEEL ALMIRAH, SIZE 900MM(L)X 450MM(D)X 1830MM(H) BODY MADE OUT IN 22 GAGUE(0.8MM) & DOOR 19 GAGUE(1 MM) CRCA SHEET. 4 ADJUSTABLE SHELVE IN 22 GAGUE(0.8MM) & PEDESTAL 18 GAGUE 1.2 MM CRCA SHEET.HAVING FOUR SHELVES MAKING FIVE COMPARTMENT, FITTED WITH MS BODY LOCK & HANDLE. WITH 2 NUMBERS OF GLASS DOOR SHUTTERS , THE GLASS USED SHALL BE 4MM THICK CLEAR. UNIFORMLY DISTRIBUTED LOAD CAPACITY OF EACH SHELF SHALL BE 30 KG MAXIMUM. EACH RACK SHALL BE PROVIDED WITH STIFFENER AT BOTTOM FOR STRENGTH. THE ENTIRE BODY PANEL AND SHELF SHALL BE MADE OF HIGH YIELD STRENGTH,THE COMPLETE STEEL STRUCTURE SHALL BE CONSTRUCTED BY WELDING AND PROVIDE FINISHING WITH EPOXY POLYESTER POWDER COATED TO THE THICKNESS 50-60 MICRONS(+/-5 MICRON) IN COLOR GREY-LIGHT GREY,THE PRODUCT MUST BE FROM A MANUFACTURER HAVING ISO 9001,ISO 14001 ,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX,SEFA CERTIFICATE. (Make - Durian/ Equivalent, MODEL NO:BECKETT/G/A/1830)

SUPPLYING AND PLACING OF VERTICAL FILING CABINET OF SIZE 470MM(L)X 600MM(D)X 1370MM(H) 4 DRAWER VERTICAL FILING CABINET IT HAS 1 POINT LOCKING MECHANISM AND A RIGID KNOCK DOWN CONSTRUCTION. THE TOP, SIDE & DRAWER FRONT THICKNESS SHOULD BE 0.7MM. THE FRAMES, DRAWER-INSIDE COVER AND SIDE BACK SIDE THICKNESS SHOULD BE 0.6MM. THE BACK, BOTTOM AND DRAWER THICKNESS SHOULD BE 0.5MM. EASY TO GRIP FULL LENGTH RECESS HANDLE SHALL BE INTEGRATED INTO METAL DRAWER FOR EASY PULL OUT CONVENIENCE. THERE SHALL BE A SNAP ON TYPE PLASTIC LABEL HOLDER ON DRAWER FRONTS. THE CENTRALIZED LOCKING SYSTEM SHALL BE PROVIDED ALONG WITH SHOOTING BOLT MECHANISM AND 10 LEVER CAM LOCK. THE FINISHING SHALL INCLUDE EPOXY POWDER COATED TO THE THICKNESS OF 50 MICRONS (+/- 10). IN COLOR GREY,THE PRODUCT MUST BE FROM A MANUFACTURER HAVING ISO 9001,ISO 14001 ,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX,SEFA CERTIFICATE. (Make - Durian/ Equivalent, MODEL NO:TINKLER)

SUPLYING ANF PLACING OF RECEPTION TABLE,DURIAN MODEL PELAM L SHAPE MADE OF PRELAMINATED PARTICLE BOARD IN BAVERIAN BOARD COLOR WITH MAIN TABLE SIZE 1800MM(L)X 600MM(D)X 750MM(H), EXTRA TOP 10MM THK CLEAR GLASS COUNTER TOP WITH S.S. STUDS.THE PRODUCT MUST BE FROM A MANUFACTURER HAVING ISO 9001,ISO 14001 ,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX,SEFA CERTIFICATE.(Make - Durian/ Equivalent, MODEL NO:PETRA)

Suplying and placing of Medium Back Chair, Size: (W)585mm X (D)660mm X (H)1060mm • Mesh back with Adjustable Lumbar Support. • Fabric Upholstered seat with Moulded Foam. • Synchro Single Locking Mechanism. • Fix Armrest • Nylon Base with Smooth Nylon Castor. THE PRODUCT MUST BE FROM A MANUFACTURER HAVING ISO 9001,ISO 14001 ,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX,SEFA CERTIFICATE. (Make - Durian/ Equivalent, MODEL NO:-DEFINE/MB/STANDARD)

Supply and Installation of Sofa Set (3+1+1) with arm. sofa seat, back and arms are made up of solid pine wood with hot pressed ply wood and upholstered with leatherette. Sofa molded with polyurethane foam with high density and back plywood shall be designed with contoured lumbar support for extra comfort.Total Seating Arrangment 5 Seater, 1 STR Size : (L)640mm X (D)720mm X (H)845mm, 3 Str Size- (L)1760mm X (D)720mm X (H)845mmTHE PRODUCT MUST BE FROM A MANUFACTURER HAVING ISO 9001,ISO 14001 ,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX,SEFA CERTIFICATE. (Make - Durian/ Equivalent, MODEL NO:-JESSE)

Suplying and placing of Center Table,Inspired by classic mid-century designs, the Casper, our iconic wooden center table celebrates a marriage of simplicity and functionality. Resting a top a clear glass, it create a stunning contrast of modern and rustic. Product Dimension : (W)1150mm X (D)550mm X (H)450mm,Variation : Solid Wood Coffee Table,THE PRODUCT MUST BE FROM A MANUFACTURER HAVING ISO 9001,ISO 14001 ,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX,SEFA CERTIFICATE. (Make - Durian/ Equivalent, MODEL NO:-CASPER/CT)

Supply and Installation of the Office Series Is Comprised Of Desks, File Cabinets And Multipurpose Storage Units. Constructed From Engineered Wood And Finished In Black Oak For A Superior Feel And Finish. The Unit Comprises Of Long Stacked Horizontal Shelves Encased In Wooden Shutters. The File Cabinet And Sideboard Is A Perfect Addition To The Wall Or On The Side Next To The Theon Office Desk For Storing Your Files, Documents And Important Papers. A Set Of Drawers Also Add Value For Storing Your Stationery And Knicks Knacks For Ease. Get Your Office The Theon Storage Series For A Clutter-Free Office. Product Dimension : (W)2000mm X (D)500mm X (H)750mm, THE PRODUCT MUST BE FROM A MANUFACTURER HAVING ISO 9001,ISO 14001 ,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX,SEFA CERTIFICATE. (Make - Durian/ EquivalentMODEL NO:-THEON/C)

Providing, fixing and installation of Luggage storage unit of dimensions 1050x1200x500(hxwxd) made of 19 mm waterproof solid ply finished with 1mm laminate on outer face and 0.8mm laminate on inner surface of approved shade and make as per design with all necessary hardware and fittings all complete.

Providing, fixing and installation of Dresser with fridge storage unit of dimensions 2400x600x500 (hxwxd) made of 19 mm waterproof solid ply finished with 1mm laminate on outer face and 0.8mm laminate on inner surface of approved shade and make as per design with all necessary hardware and fittings all complete.

Providing, fixing and installation of customised TV unit of dimensions 2400x1500x375(hxwxd) made of 19 mm waterproof solid ply finished with 1mm laminate on of approved shade and make as per design with attached drawers etc, with all necessary hardware and fittings all complete

Providing, fixing and installation of customised Study table of dimensions 750x1200x600(hxwxd) made of 19 mm waterproof solid ply finished with 1mm laminate on outer face and 0.8mm laminate on inner surface of approved shade and make as per design, with 10mm tempered glass on top, with attached drawers and all necessary hardware and fittings all complete.

Room Curtain- Day Curtain and Night Curtain Make- Asian Paints (Ador),D Décor, F&F

MATTRESS (Size-78''x72''x5''), Make- King Koil, Tempur, Saatva

BED RUNNER (Size-5-0x2-0), Make- Natura, Obsession, My home

WALLPAPER Make- Wall art, Wall Fashion, Wall King

FOOT MAT- Make- Natura, Obsession, My Home

BATH MAT ( Size-40x60)- Make- Natura, Obsession, My Home

BATH TOWEL Make- Micasa, Welspun, Bombay Dying

DOUBLE BED SHEET (Size-108x108) Make- Micasa, Welspun, Bombay Dying

HAND TOWEL (Size-16x24) Make- Micasa, Welspun, Bombay Dying

PILLOW (CLOUD), Make- King Koil, Tempur, Saatva

PILLOW COVER Make- Micasa, Welspun, Bombay Dying

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII

BANQUET HALL ( CURTAIN) 110-0X10-0, Make-Asian Paint Ador, D Décor, F&F

RESTAURENT 5 PC BLINDS ( LUZON) 8-0 x 5-0 , Make-Marvel Décor, Hunter Douglas, MAC

Providing and placing Artistic Canvas Painting for guest rooms,Lobby And Passages (Not-original work; printed on canvas with frame) artwork, using premium acrylic emulsion paint of exterior quality, over white cement based putty surface. Artwork design to be approved by consultant architect prior to execution.

Providing and placing Artistic Canvas Painting for entrance foyer, (Original painted figurative on canvas with frame) artwork, using premium acrylic emulsion paint of exterior quality, over white cement based putty surface. Artwork design to be approved by consultant architect prior to execution.

Add 18% GST

Add 1% Labour cess 1%

M/S MADAN PRASAD

M/S PRASAD CONSTRUCTION & CO

M/S ADARSH CONSTRUCTION

M/s R.S.Agrawal

m/s b rai construction company