Repair and maint of various types of wooden furniture items at AFS Jodhpur

Amount

BED HARD/BED PLY TOP : ( Drg No. FD-213,217, 246/ 247)

M&L for removal of u/s ply wood of bed in any position, S&F new ply wood 12 mm thick, BWR grade, ISI marked including fixing in same position all as shown on drg with suitable size screws & cup washers, all specified and directed by the Engineer-in-Charge

M&L for removing u/s headrest and S&F New headrest complete of 1st class hard wood teak frame (Well-seasoned) duly covered with 4mm thick teak veneer ply complete all as specified & shown in drg.

M&L for removing u/s footrest and S&F New footrest complete of 1st class hard wood teak frame (Well-seasoned) duly covered with 4mm thick teak veneer ply complete all as specified & shown in drg.

M&L for removing of u/s long rail and S&F of new new long rail made out of fully seasoned Ist class hard wood all as specified & shown in drg.

M&L for removing of u/s support/Stiifner and S&F of new support made out of 2nd class hard wood (Well-seasoned) and all as specified & shown in drg.

M&L for removal of u/s veneer ply of Headrest of bed complete in any position, S&F new 4 mm thick one side teak veneered ply on both sides, all round teak beading all as shown on drg, as specified and directed by Engr-in-charge

M&L for removal of u/s veneer ply of Footrest of bed complete in any position, S&F new 4 mm thick one side teak veneered ply on both sides, all round teak beading all as shown on drg, as specified and directed by Engr-in-charge

S& F new bracket of size 100 x 100 x 30 mm made of hard wood and fixing with 02 Nos suitable size steel screws complete as all as specified and directed.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of French polish of smooth finishing complete all as specified on drawing or as directed by Engineer-in-charge.

Chair dining : (Drg No. FD-16,203, 228, 262, 270,279 ) : Removing of old unserviceable the following parts from chair dining, and supply and fixing new same parts of hard wood duly finished with existing shape and fixed with bamboo pin and fevicol including tightening of other joints and applying 2 coats of French polish after preparation of existing surfaces complete all as shown on drg and as directed by Engineering-in-charge

Front legs (L&R)

Rear legs (L&R)

Side rail with holes (L&R) side for canning

Front and back Rails with holes for canning

Stiffener bottom

Back rest

French polishing to the repaired chair dining in two coats after preparation of surfaces all as specified on drawing or as directed by Engineer-in-charge.

Recaning of repaired chair dining with best quality of approved plastic cane of white or cream ivory all as specified on drawing or as directed by Engineer-in-charge.

Chair writing (Drg No. FD-20,202,250, 280 ) : Removing of old unserviceable the following parts from chair writing, and supply and fixing new same parts of hard wood duly finished with existing shape and fixed with bamboo pin and fevicol including tightening of other joints and applying 2 coats of french polish after preparation of existing surfaces complete all as shown on drg and as directed by Engineering-in-charge

Front legs (L&R)

Rear legs (L&R)

Side rail with holes (L&R) side for canning

Front and back side rails with holes for canning

Stiffener bottom

Back rest

Hand rest

French polishing to the repaired chair writing in two coats after preparation of surfaces all as specified on drawing or as directed by Engineer-in-charge.

Recaning of repaired chair writing with best quality of approved plastic cane of white or cream/ivory all as specified on drawing or as directed by Engineer-in-charge.

Chair easy (Drg No. FD-17,201,229) : Removing of old unserviceable the following parts from chair easy, and supply and fixing new same parts of hard wood duly finished with existing shape and fixed with bamboo pin and fevicol including tightening of other joints and applying 2 coats of french polish after preparation of existing surfaces complete all as shown on drg and as directed by Engineering-in-charge

Front legs (L&R)

Rear legs (L&R)

Side rail with holes (L&R) side for canning

Front and back rails with holes for canning

Back rail top and bottom of frame with holes for canning as per drg

Back rail ( L&R) back frame with holes for canning as per drg

Stiffener bottom

Hand rest

French polishing to the repaired chair easy in two coats after preparation of surfaces all as specified on drawing or as directed by Engineer-in-charge.

Recaning of repaired chair easy with best quality of approved plastic cane of white or cream/ivory all as specified on drawing or as directed by Engineer-in-charge.

CHAIR DINING WITH CUSHION (Drg No. TP, FD/E6/MAP/10 ) : S&F of following existing old broken wooden components of chair dining similar items carefully without disturbing the adjoining parts and new components made out of hard wood in lieu of dismantled components including tightening the joints, pinning, screwing, nailing, gluing, placing every part in-tact all as specified in Drg and directed by Engr - In Charge.

Back rest Stiffener

Bottom leg stiffener

Front legs

Rear Legs

Rubber/PVC shoes

Replacement of cloth for seat of repaired chair dining with cushion best quality of approved cloth of various all as specified on drawing or as directed by Engineer-in-charge.

Replacement of cloth for back of repaired chair dining with cushion best quality of approved cloth of various all as specified on drawing or as directed by Engineer-in-charge.(for TP Chair Dining with cushion only)

M&L for preparation of wooden surfaces of chair dining with cushion by scraping with sand paper, re-dusting and apply putty wherever required and polishing the surface with french polish to get glossy finish all as directed by Engr-in-Charge.

Side Board ( Drg No. FD-26, 241, 371 ) :

Removing old unserviceable / broken top from side board S/F New Top of 18mm thick pre laminate particle board Ex grade BWR of approved shad, ISI mark and fixing in potion including 4mm thick 1st class H.W beading all around the Top all as shown in drg and as directed by Engineer-in-charge

Removing of old unserviceable broken shutter from side board and supply and fix new shutter of 18 mm thick pre-laminated particle board exterior grade one side teak shade other side white in colour including 4 mm thick hard wood beading around the top and fixing in position with piano hinges all as shown on drg and as directed by Engineer-in-charge.

Removing of old unserviceable particle board (L&R) side from side board and supply and fix new L&R side pre-laminated particle board 18 mm thick of approved shade and fixing in position all as shown on drg and as directed by Engineer-in-charge.

Removing old unserviceable back ply from side board S&F back ply of 6mm thick both side commercial, ISI mark and fixing in position all as shown un drg & as directed by Engineer-in-charge.

Removing old unserviceable leg from side board S&F New ledges of Hardwood and fixing in position with screw / Nails all as shows on drg and a directed by Engineer-in-charge.

Removing old unserviceable / broken knob from side board S&F New knob of 38 to 40mm dia plastic knob and fixed with required screw all as shown on drg & as directed by Engineer-in-charge.

Removing old unserviceable drawer from side board and S&F New drawer in position all as shown on drg & as directed by Engineer-in-charge.

M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of side board.

SOFA SET 1/4/ 5 PERSON WITH CUSHION (Drg No. FD-281, FD/E6/MAP/10 )

Removing the existing unserviceable tapestry cloth, cushion of sofa set and replacing with new tapestry cloth including mulmul with foam cushion 40 density 100mm thick of size 558mm x 533mm x 100mm, rest all as shown on drg and as directed by Engr-in-Charge. Note :- (i) Each cushion for seat or back will be measured as single unit. (ii) The tapastry cloth shall be mat finish and shall not less than Rs. 350/- per metre and as approved by Engr-in-Charge.

Removing the existing unserviceable tapastry cloth of sofa set and replacing with new tapastry cloth mat finish of size 558mm x 533mm x 100mm with mulmul cloth.

Removing the existing unserviceable front leg from Sofa and providing new hard wood of leg size 70mm x 35 mm x 300mm, rest all as shown on drg and as directed by Engr-in-Charge.

Removing the existing unserviceable rear leg from Sofa and providing new hard wood leg size as shown on drg and as directed by Engr-in-Charge.

Removing existing unserviceable Arm rest from Sofa and providing new hard wood Arm Rest of size as shown on drg and as directed by Engr-in-Charge.

Removing existing unserviceable side rail from Sofa and providing new hard wood side rail of size as shown on drg and as directed by Engr-in-Charge.

Removing existing unserviceable bearer from Sofa and providing new hard wood bearer of size as shown on drg and as directed by Engr-in-Charge.

Removing existing unserviceable battens from Sofa and providing new hard wood battens of size 50mm x 20 mm, rest all as shown on drg and as directed by Engr-in-Charge.

Removing existing unserviceable front rail from Sofa three seater and providing new hard wood front rail of size as shown on drg and as directed by Engr-in-Charge.

Removing existing unserviceable front rail from Sofa single seater and providing new hard wood front rail of size as shown on drg and as directed by Engr-in-Charge.

M & L for fixing of PVC shoes superior quality with fixing of screws as specified & directed by Engr-in-charge.

M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of sofa set 4 Seater and as directed

M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of sofa set 5 Seater and as directed

TABLE CENTER TWO TIER (Drg No. FD/MAP/08, 393) : The following repair shall be carried out to Table centre two tier after removing old UNSV parts and replacing with new parts of well seasoned hard wood free from pits & Knots as under complete all as specified under directed:-

Long Rail

Short Rail

Centre stiffner

Rubber/PVC shoes

Removing of unserviceable/ broken top from table centre two tier supply and fix new top of table centre two tier of prelaminated particle board of 18 mm thick BWR exterior grade ISI ma with Teak wood beading all around the top duly polished all as shown on drg and as directed

French polishing to the repaired Table Centre two tier with two coats after preparation of surfaces all as specified on drawing or as directed by Engineer-in-charge.

Table centre (Drg No. FD-29,235,274) Removing of old unserviceable the following parts from table centre supply and fix new following parts of hard wood duly finished in shape and tightening of other joints duly polished after repair work size all as shown on drg and as directed by Engineer-in-charge.

Front and back rails of centre table

Side rails ( L&R)

Legs for table centre

Stiffener

Removing of unserviceable/ broken top from table centre two tier supply and fix new top of table centre of prelaminated particle board of 18 mm thick BWR exterior grade ISI mark with Teak wood beading all around the top duly polished all as shown on drg and as directed

French polishing to the repaired Table centre in two coats after preperation of surfaces all as specified on drawing or as directed by Engineer-in-charge.

Tea poy (Drg No. FD-34,232,278, 382) Removing of old unserviceable the following parts from tea poy, and supply and fix new following parts of hard wood duly finished in shape in existing position of size all as shown on drg and as directed by Engr-In Charge.

Front and back rails of table

Side rails ( L&R)

Stiffener

Removing of unserviceable/ broken top from tea poy fabrication and fixing top of pre-laminated particle board of 18 / 19 mm thick BWR exterior grade ISI mark including supply and fixing of 4 mm thick first class hard wood teak wood beading around the top duly polished all as shown on drg and as directed

French polishing to the repaired Teapoy in two coats after preparation of surfaces all as specified on drawing or as directed by Engineer-in-charge.

Table peg (Drag No. FD- 25,236,266, 277,384) Removing of old unserviceable the following parts from table peg supply and fix new following parts of hard wood duly finished in shape and tigheting of other joints duly polished after repair work all as specified in drg and as directed by Engineer-in-charge.

Front and back rails of table

Side rails ( L&R)

Stiffener (Bottom)

Removing of unserviceable/ broken top from table peg fabricating and fixing of top of pre-laminated particle board of 18 mm thick BWR exterior grade ISI mark including supply and fixing of 4 mm thick teak wood beading around the top duly polished all as shown on drg and as directed

French polishing to the repaired Table Peg in two coats after preparation of surfaces all as specified on drawing or as directed by Engineer-in-charge.

Table 3' x 2' with or without drawer (Drg No. FD-41,224,283, 42,209,223, 231,284) :Removing of old unserviceable the following parts from table 3' x 2' with or without drawer and supply and fix new following parts of hard wood duly finished in shape and tightening of other joints duly polished after repair work all as specified in drg and as directed by Engineer-in-charge.

Front and back rails

Side rails

Stiffener

New drawer

Removing of unserviceable/ broken top from table 3'x 2' with or without drawer of pre-laminated particle board of 18 mm thick one side teak face exterior grade ISI mark fabricating and fixing on the frame of table 3' x 2 ' size including 4 mm thick teak wood beading around the top duly polished after repair work all as shown on drg and as directed by Engineer-in-charge.

French polishing to the repaired Table 3' x 2' with or without drawer in two coats after preparation of surfaces all as specified on drawing or as directed by Engineer-in-charge.

Table writing (Drg No. FD-33, 249, 268,275) :Removing of old unserviceable the following parts from table writing supply and fix new following parts and fixing in same position all as shown on drg and as directed by Engineer-in-charge.

Removing of unserviceable top from table writing and supply and fix new top of 18 mm thick pre-laminated particle board exterior grade one side teak shade other side white in colour including 4 mm thick of teak wood beading around the top duly fixing in position including polishing after repair wok all as shown on drg and as directed

M&L for removing old u/s legs and S&F new legs made out of teak wood duly finished/ smoothened complete all as specified & shown in drg and as directed.

Removing of old unserviceable side stiffener from table writing and ply and fixing new stiffener made from seasoned hard wood duly finished with existing shape as per respective drawings in position with screw/nails all as shown on drg and as directed.

Removing of old unserviceable bottom stiffener from table writing and supply and fixing new bottom stiffener made from seasoned hard wood duly finished with existing shape as per respective drawings in position with screw/nails all as shown on drg and as directed.

M&L for removing old u/s drawers and S&F new drawers complete all as specified & shown in drg.

Replacement of shutter of 18 mm thick pre-laminated particle board with knob of 38 to 40 mm dia reqd as per drg

M & L for Replacement of left/right side of box of table of 18 mm thick pre-laminated particle board exterior grade one side teak shade other side white in colour as specified.

M & L for Replacement of back side ply 6 mm thick for box of the table writing as specified in drg.

M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of French polish to old and new surface of table and as directed

TABLE Dining 3'x3' (900x900) (Drg No. FD-88/291) : Repair to table dining 3'x3' (OR's) including dismantling/removal of all broken parts and replacing with new parts of hard wood as under complete all as specified under directed:-

Top made out of 18mm thick pre laminated particle board shade and texture as approved by engineer in charge with matching hard wood edging.

Leg made out of hard Wood

Long Rail made out of hard Wood

Short Rail made out of hard Wood

S& F new bracket of size 100 x 100 x 30 mm made of 1st class hard wood and fixing with 02 Nos suitable size steel screws complete as directed by Engr-in-charge

stiffener made out of hard Wood

Rubber/PVC shoes

M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table and as directed

TABLE DINING 4 PERSON (1200X900) (Drg No. FD - 273 ) : Repair to table dining 4 pers including dismentalling/removal of all broken parts and replacing with new parts of hard wood as under complete all as specified under directed:-

Top made out of 18mm thick pre laminated particle board shade and texture as approved by engineer in charge with matching Indian Teak wood edging.

Leg made out of hard Wood

Long Rail made out of hard Wood

Short Rail made out of hard Wood

S& F new bracket of size 100 x 100 x 30 mm made of 1st class hard wood and fixing with 02 Nos suitable size steel screws complete as directed by Engr-in-charge

Centre stiffener made out of hard Wood

Rubber/PVC shoes

M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table and as directed

Table dining 6 persons (Drg No FD- 239, 269, 273, 376) : Removing of old unserviceable following parts from table dining 06 pers and supply and fix new following parts of hard wood duly finished in shape in fixing in position with new bamboo pins and fevicol all as shown on drg and as directed by Engr-In-Charge.

Front and back rails

Side rails

Stiffener bottom

Bottom support

S& F new bracket of size 100 x 100 x 30 mm made of 1st class hard wood and fixing with 02 Nos suitable size steel screws complete as directed by Engr-in-charge

Removing of unserviceable top from table dining 06 persons and supply and fix new top of 18 / 19 mm thick pre-laminated particle board exterior grade one side teak shade other side white in colour including teak wood beading around the top all as specified and directed.

M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table and as directed.

Table dining 8 persons (Drg No. FD-273, 376): Removing of old unserviceable following parts from table dining 08 pers and supply and fix new following parts of hard wood duly finished in shape in fixing in position with new bamboo pins and fevicol all as shown on drg and as directed by Engr-In-Charge.

Front and back rails

Side rails ( L&R)

Legs for table dining 08 pers

Stiffener bottom

Support for table bottom of the top

Removing of unserviceable top from table dining 08 persons and supply and fix new top of 18 mm thick pre-laminated particle board exterior grade one side teak shade other side white in colour including first class hard wood teak wood beading around the top duly polished after complete of repair work, all as shown on drg and as directed

Applying of French polishing to the Table dining 8 persons in two coats after preparation of surfaces all as specified on drawing or as directed by Engineer-in-charge.

TABLE DRESSING LADIES (Drg No. FD-32(M), 251)

S&F in repairs table top of Table dressing ladies with 18 mm thick pre-laminated particle Board of approved make, all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs new Glass shuttrs of Table dressing ladies all as specified on drawing or as directed by Engineer-in-charge.(Each glass shutter shall be measured as single unit)

M & L for complete Lower box made out of Prelaminated particle board with drawer all etc complete all as per drawing as specified & as directed by Engr-in-Charge:-(back shall be 06 mm ply)

M&L for removing old u/s broken looking mirror and S&F new looking mirror of size 760 x 380 x 5mm & frame made out of teak wood of size 25 x 6 mm & 6mm thick commercial ply on back including polishing the frame complete all as directed.

Supply & fixing of Knob of aluminium anodized dark brown in shade as approved and fixing with screws as specified & as directed by Engr-in-Charge:-

M & L for fixing of PVC shoes superior quality fixing with screws as specified & directed by Engr-in-charge.

M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of french polish to old and new surface of table and as directed

KAMAL ENTERPRISES (BID ID -3301343)

SNEH CORPORATION (BID ID -3300018)

shekhar & company (BID ID -3296074)

M/S R R ENTERPRISES (BID ID -3294713)

SK INDUSTRIES (BID ID -3296148)