Construction of office building for Savarkundla division, M.T. Lab, Rural sub division at 220 kv S/s Savarkundla under Amreli circle.

Name of Work:- Construction of office building for Savarkundla division, M.T. Lab, Rural sub

division at 220 kv S/s Savarkundla under Amreli circle

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

1 Excavation for foundation up to 1.5 M. depth. Incl. sorting out and

stacking of useful materials and disposing of the excavated stuff

up to 50 meter Lead in-(A)- Loose soil 115.00 121.72 Cmt

2 Excavation for foundation up to 1.5 M. depth. Incl. sorting out and

stacking of useful materials and disposing of the excavated stuff

up to 50 meter Lead in (B)- Dense or Hard Soil 217.00 155.60 Cmt

3 Excavation for foundation up to 1.5 M. depth. Incl. sorting out and

stacking of useful materials and disposing of the excavated stuff

up to 50 meter Lead in- (C)- Hard murrum 211.00 266.26 Cmt

4 Excavation for foundation for depth from 1.5 Mt to 3 Mt. depth

including sorting out and stacking of useful materials and

disposing of the excavated stuff upto 50Mt. Lead in (C)- Hard 162.00 284.37 Cmt

5 Excavation for foundation for depth from 1.5 Mt to 3 Mt. depth

including sorting out and stacking of useful materials and

disposing of the excavated stuff upto 50Mt. Lead in (D)- Soft rock

not requiring Blasting 60.00 297.05 Cmt

6 Filling available excavated earth (excluding rock) trenches, plinth

side of foundation etc. in layer not exceeding in 20 cm. in depth

consolidating each deposited layer by ramming & watering. 590.00 135.56 Cmt

7 Filling in foundation and plinth with murrum or selected soil

brought from out side with any lead in layers of 20 cm. Thickness

including watering, pnumatic ramming and consolidating etc.

comp 1186.00 298.79 Cmt

8 Filling in plinth with sand under floor including watering,

ramming, consolidating and dressing etc. completed. 95.00 477.03 Cmt

9 Applying general insecticide pest control treatment to floors,

cupboards etc including labour material etc. complete. Using

Heptachloride 20 EC. As Per 6113_pests Consentration Weight

0.50 percent is recommended one litre chemical emulsion dillute

with 39 liter of water will give. Total dillute concrentration will be

40 litre inclusive of one litre chemical emulsion appication

Litre chemical / Sqm of surface is recommended as per I.S 430.00 38.70 Smt

10 Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse

sand : 4- graded stone aggregates 20 mm nominal size) and curing

complete excluding cost of formwork in (A) Foundation and Plinth

11 Providing and laying controlled cement concrete M 250 and curing

complete including the cost of form work and excluding

reinforcement for reinforced concrete work in(A)- foundation

footings, Base of Columns and mass concrete 109.00 5442.00 Cmt

12 Providing and laying controlled cement concrete M 250 and curing

complete including the cost of form work and excluding

reinforcement for reinforced concrete work in column Gorund

floor. 38.00 8799.00 Cmt

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

13 Providing and laying controlled cement concrete M 250 and curing

complete including the cost of form work and excluding

reinforcement for reinforced concrete work in column First Floor. 20.00 8840.00 Cmt

14 Providing and laying controlled cement concrete M 250 and curing

complete including the cost of form work and excluding

reinforcement for reinforced concrete work in column Second

Floor. 17.00 8881.00 Cmt

15 Providing and laying controlled cement concrete M 250 and curing

complete including the cost of form work and excluding

reinforcement for reinforced concrete work in column Third Floor.

16 Providing and laying controlled cement concrete M 250 and curing

complete including the cost of form work and excluding

reinforcement for reinforced concrete work in Beam Ground

Floor. 111.00 6869.00 Cmt

17 Providing and laying controlled cement concrete M 250 and curing

complete including the cost of form work and excluding

reinforcement for reinforced concrete work in Beam First Floor. 59.00 6910.00 Cmt

18 Providing and laying controlled cement concrete M 250 and curing

complete including the cost of form work and excluding

reinforcement for reinforced concrete work in Beam Second

Floor. 39.00 6951.00 Cmt

19 Providing and laying controlled cement concrete M 250 and curing

complete including the cost of form work and excluding

reinforcement for reinforced concrete work in Beam Third Floor. 7.00 6992.00 Cmt

20 Providing and laying controlled cement concrete M 250 and curing

complete including the cost of form work and excluding

reinforcement for reinforced concrete work in(C)-Slabs landing

stair etc at Ground Floor. 73.00 7277.00 Cmt

21 Providing and laying controlled cement concrete M 250 and curing

complete including the cost of form work and excluding

reinforcement for reinforced concrete work in(C)-Slabs landing

stair etc at First Floor. 68.00 7318.00 Cmt

22 Providing and laying controlled cement concrete M 250 and curing

complete including the cost of form work and excluding

reinforcement for reinforced concrete work in(C)-Slabs landing

stair etc at Second Floor. 42.00 7360.00 Cmt

23 Providing and laying controlled cement concrete M 250 and curing

complete including the cost of form work and excluding

reinforcement for reinforced concrete work in(C)-Slabs landing

stair etc at Third Floor. 2.00 7401.00 Cmt

24 Providing TMT Bar FE 500/500D reinforcement for R.C.C. work

including bending, binding and placing in position complete upto

floor two level Ground Floor. 39740.00 76.52 Kg

25 Providing TMT Bar FE 500/500D reinforcement for R.C.C. work

including bending, binding and placing in position complete at

First Floor 18375.00 77.56 Kg

26 Providing TMT Bar FE 500/500D reinforcement for R.C.C. work

including bending, binding and placing in position complete at

Second Floor 12250.00 78.60 Kg

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

27 Providing TMT Bar FE 500/500D reinforcement for R.C.C. work

including bending, binding and placing in position complete at

Third Floor 1875.00 79.64 Kg

28 Brickwork using common burnt building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in

Cement Mortar 1:5. (1- Cement : 5 -fine sand) 71.00 4203.06 Cmt

29 Brickwork using common burnt bricks having crushing strength

not less than 35 kg./Sq.Cm. in Super Structure up to floor two

level. in Cement Mortar 1:5 (1- Cement : 5 -fine sand) Ground

floor 121.00 4481.99 Cmt

30 Brickwork using common burnt bricks having crushing strength

not less than 35 kg./Sq.Cm. in Super Structure up to floor two

level. in Cement Mortar 1:5 (1- Cement : 5 -fine sand) First Floor 102.00 4523.69 Cmt

31 Brickwork using common burnt bricks having crushing strength

not less than 35 kg./Sq.Cm. in Super Structure up to floor two

level. in Cement Mortar 1:5 (1- Cement : 5 -fine sand) Second

Floor 84.00 4565.39 Cmt

32 Brickwork using common burnt bricks having crushing strength

not less than 35 kg./Sq.Cm. in Super Structure up to floor two

level. in Cement Mortar 1:5 (1- Cement : 5 -fine sand) Third Floor

33 Half Brick masonary in common burnt building bricks having

crushing strength not less than 35 Kg. / Sqmt. in cement mortar 1:4

(1-Cement : 4-Coarse Sand) in above Plinth level up to floor two

level - GF. 66.00 677.49 Smt

34 Half Brick masonary in common burnt building bricks having

crushing strength not less than 35 Kg. / Sqmt. in cement mortar 1:4

(1-Cement : 4-Coarse Sand) above floor two level - FF. 31.00 683.73 Smt

35 Half Brick masonary in common burnt building bricks having

crushing strength not less than 35 Kg. / Sqmt. in cement mortar 1:4

(1-Cement : 4-Coarse Sand) above floor two level - SF. 10.00 689.97 Smt

36 Providing and fixing MS wire mesh(Chicken mash) at every joint

of masonary and concrete, or any joint includding all fixtures and

fittings as directed by EIC. 414.00 216.00 Smt

37 Providing 15 mm. Thick cement plaster in single coat on both

sides Brick/concrete walls for interior plastering up to floor two

level and finished even and smooth in (i) C.M.1:3 (1cement :

sand)- For walls Ground Floor. 1426.00 193.49 Smt

38 Providing 15 mm. Thick cement plaster in single coat on both

sides Brick/concrete walls for interior plastering up to floor two

level and finished even and smooth in (i) C.M.1:3 (1cement :

sand)- For walls First Floor. 1008.00 217.15 Smt

39 Providing 15 mm. Thick cement plaster in single coat on both

sides Brick/concrete walls for interior plastering up to floor two

level and finished even and smooth in (i) C.M.1:3 (1cement :

sand)- For walls Second Floor. 615.00 240.81 Smt

40 Providing 10 mm. Thick cement plaster in single coat on both

sides Brick/concrete walls for interior plastering up to floor two

level and finished even and smooth in (i) C.M.1:3 (1cement :

sand)- For Celling in Ground Floor 435.00 170.01 Smt

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

41 Providing 10 mm. Thick cement plaster in single coat on both

sides Brick/concrete walls for interior plastering up to floor two

level and finished even and smooth in (i) C.M.1:3 (1cement :

sand)- For Celling in FF 463.00 191.68 Smt

42 Providing 10 mm. Thick cement plaster in single coat on both

sides Brick/concrete walls for interior plastering up to floor two

level and finished even and smooth in (i) C.M.1:3 (1cement :

sand)- For Celling in SF 266.00 213.35 Smt

43 20 mm. Thick sand faced cement plaster on walls up to height

meters above ground level consisting of 12 mm. Thick backing

coat of C.M. 1:3 (1 cement : 3 sand) and 8 mm. Thick finishing

coat of C.M.. 1:1 (1 cement : 1 sand) etc. complete - all floor. 1924.00 339.02 Smt

44 Providing and laying Broken China Mosaic flooring for terrace

using 12 mm to 20mm broken pieces of glazed tiles to be laid over

cement mortrar 1:3 to plain or slope and to be tampred to bring

mortar creme out up to surface using white cement including

rounding off junctions and extending them up to 15cm along the

wall, clearing with water and oxalic acid etc. as directed. 470.00 771.98 Smt

45 Providing and laying 24" x 24" size of Double charged Vitrified

8mm thick tiles flooring over 20mm (Average) base of Cement

Mortar 1:6 (1-Cement : 6 Coarse Sand) on new surface or fixing

on existing flooring by adhesive materials including dismentalling

of existing flooring including Grouting the joints of flooring tiles

having joints of 3mm width, using epoxy grout mix of 0.65 kg of

orgenic coated filler of desired shade (0.15 kg of hardener and

kg of resin per kg), including filling the grout and finished with

flush pointing & cleaning the surface etc. complete for Light 1075.00 1345.89 Smt

46 Providing and laying 24" x 24" size of Double charged Vitrified

8mm thick tiles flooring over 20mm (Average) base of Cement

Mortar 1:6 (1-Cement : 6 Coarse Sand) on new surface or fixing

on existing flooring by adhesive materials including dismentalling

of existing flooring including Grouting the joints of flooring tiles

having joints of 3mm width, using epoxy grout mix of 0.65 kg of

orgenic coated filler of desired shade (0.15 kg of hardener and

kg of resin per kg), including filling the grout and finished with

flush pointing & cleaning the surface etc. complete for Antiskid 61.00 1547.19 Smt

47 Providing and laying coloured glazed tiles of the size 300mm x

200mm x 8mm / 300mm x 450mm x 8mm or larger size in

flooring, skirting, risers of steps and dedo on 10mm thick cement

plaster 1:3 (1-Cement : 3-Coarse sand) & jointed with white

cement slurry. 473.00 1473.50 Smt

48 Providing and laying kotah stone slab 25 mm thick in riser of

steps, dedo and pillars laid on 10mm thick cement mortar 1:3(1-

cement : 3coarse sand ) and jointed with grey cement Slurry

mixed with pigment to match the shade of slab including rubbing

and polishing etc. completed, kotastone-25mm thick 30.00 1098.09 Smt

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

49 Providing & laying 20 to 25mm thick, both faces polished kotah

stone with all edges machine cut up to 450mm width and of

required length (only one piece to be used) of approved quality for

cupboard shelves including fixing the same in masonry wall by

cement mortar in three sides including curing etc. complete as

directed by E.I.C 221.00 953.00 Smt

50 Providing & Fixing 25mm thick both side polished kotah stone

wall partitions 600mm wide & required height & all sides

polished, machine cut & of approved quality including fixing the

same in wall in line & level etc. complete as directed by E.I.C 6.00 1091.00 Smt

51 Providing & Fixing Approved quality of 18 to 20 mm thick

polished Black Grainte required all Edges Machine polished,

machine cut & approved quality of edge moulding including fixing

the same in wall in line, sill, jamb in plumb & level etc. complete

as directed by E.I.C(rate includes edge finished molding) 265.00 3091.83 Smt

52 Providing Half round moulded round front edge for Granite/kotah

stone in trade of steps including rubbing and polishing etc.

Complete 97.00 97.75 Smt

53 Providing Quarter round moulded round front edge for

Granite/kotah stone in trade of steps including rubbing and

polishing etc. Complete 1528.00 58.65 Smt

54 Providing , Fixing & Fitting fully glazed, partly glazed

Single/Double leaf anodized /aluminum powder coted(of approved

shade) door using extruded section fabricated by standard

manufacturers with framing 63.50 x 38.10 having wt 1.094 Kg pre

Rmt rectangular section & door shutter made from with frame

vertical size 44.45 x 47.62mm having wt 1.505 Kg per Rmt and

horizontal size 63.50 x 38.10mm and bottom rail size 101.60mm

44.45mm having wt 1.60 Kg/M using 5 mm thick “TRIVENI” or

HB4 plain/colour glass/4 Acrylic Sheets/ 12 mm Board with

glazing deep rubber gasket with locking arrangement of GODREJ

LOCK with all fixtures & fastening of anodized section with

aluminum beeding without floor mounted door closer etc.

completed.. Rates are with all labours and material as per drawing

and as directed. 26.00 3900.00 Smt

55 Providing, & fixing hot pressed phenol bonded, exterior type solid

flush door 30mm shutter made by approved brand & as per I.S.I.

standard with water resisting plywood facing and 1mm thick

laminated sheet on both side of door & teak wood leaping all-

round including 100X75mm. teak wood frame.If necessary with

glass looking window with T.W. batten and polishing /Colour.

Rates are without fixtures & fastening but with 3 NO. of 100mm.

long butt or parliamentary hinges on each flap of double shutter &

150mm. long hinges for single shutter and 3 NO. of M.S. flat hold

fast grouted in C.C. (1:2:4) on each side of frame, 3 coats of oil

painting of approved shades make etc., complete as per drawing &

as directed by E.I.C. 38.00 4010.00 Smt

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

56 Providing and fixing 12 mm toughened glass door fixing with

Ozone make or equivalent floor spring, SS door handle, lock as

per approved design, door edge molding etc. Complete with

applying designer black out film on door with all required

accessories, labour and transportation complete as directed by

engineer in charge. 3.00 8307.00 Smt

57 Providing and fixing Solid PVC Flush Door Shutters 24mm thick

made fro Co- Extruded THREE LAYER RIGID PVC Foam Sheet

(Single extruded) with density not less than 600 Kg / cbm. Outer

Layer (0.8-1mm) thick should be of Rigid PVC with Density not

less than 1400 kg/cbm including Providing & Fixing WPC Door

Frame Uperline Patti of 24mm x 6mm Size. Door should be Water

proof, Termite proof, Fire Retardant & having good screw holding

capacity. Providing & Fixing 100% Solid Wood Plastic Composit

(WPC) Door Frame 90mm x 45mm made from Wood Plastic

Composite (Single extruded Process) material with dencity 780kg /

cbm All as per specifications & drawings etc. complete as per

direction of Engineer-in-charge. 45.00 4390.00 Smt

58 Providing and fixing window having extruded aluminum Colour

anodized section frame main outer size 95mm x 24mm x 1.17mm

@ wt.of 0.738 Kg/mt , horizontal Three track member size 92mm

x 31.75mm x 1.30mm,@ Wt.1.07 Kg/mt , vertical member of size

92mm x 31.75mm x 1.50mm @ Wt. 1.06 Kg/mt with sliding

shutters of horizontal membersize 40 mmx18mm x1.29mm @

wt.of 0.456 Kg/mt, vertical member of size 40mm x 18mm x

mm @ wt.of 0.456Kg/mt/ with mosquito net With good quality as

directed by EIC shutter of same size to be fixed in Three track with

5 mm thick transparent bronze colour tinted float glass with

powder coated aluminum fittings and fixtures and transparent

silicon sealant glass fixing to frame as per details etc_Alluminium

windows Three track wirh Mosquito Net 191.00 5045.00 Smt

59 Providing &fixing in position fully panneled/partly pennaled partly

glazed/ full height/ half height alluminium frame partition

anodized /aluminum powder coted(of approved shade) rectangle

section in 63.50 x 38.10 having wt 0.95 Kg vertical & horizonal to

be used for top all intermediate bottom & side ends panels.Pannels

is to be prepared from 5 mm thick Modiguard or equivalent

approved standard quality coloured/plain glass or 12 mm eco

board prelaminated both side of standard and approved quality

with glazing clip rubber gasket with aluminium bedding of

required size, All glazing should be designed with decorative film

if necessary including film charges. Scope includes all fixtures and

fastening and screws etc.completed as directed by EIC.Pennaling

is to be done as directed by EIC. 41.00 2821.00 Smt

60 Providing and fixing 12 mm toughened Glass Partition fixing with

required accessories, Complete with applying designer blackout

film on partition with all required accessories, labour and

transportation complete as directed by engineer in charge. 86.00 5795.00 Smt

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

61 Providing and fixing standared extruded of alluminium section of

size 63mm x 38.10mm x 1.2mm (Jindal Section :2434, @ Wt.

0.643 kg per mt with colour Powder Coated alluminium frame for

ventilation with 5 mm thick frosted glass as details etc complete

for Ventilation 8.00 1163.92 Smt

62 Providing & fixing MS plain grills of required pattern to wooden

frames of windows and gap filling of wall etc. with MS flats or

M.S, pipes at required spacing and frame all- round square or

round bars with round headed bolts and nuts or by screws with one

coat red oxide & two coat of oil paint (A) plain grill 4240.00 110.18 Kg

63 Steel work, welded in built up sections framed work including

cutting, hoisting, fixing in position and applying a priming coat of

read lead paint and two coat of oil paint. (A) In beams and joists,

channels angles Tees, flats, with connecting plates or angle cleats

as in main and cross beams. Hip and jack rafters, purlins conneted

to common rafters and the like. All angle, channel shall be suplly

by PGVCL. The material like nuts, bolts, and other accessories

shall be brought by contractor. 3212.00 23.00 Kg

64 Providing and fixing powder coated G.I. roofing of 0.5mm

Thickness with standard overlap as per direction of EIC and

fixing with J-Bolt and nuts and bitumen and MS washer etc.

complete as directed with all material and labour 172.00 820.00 Smt

65 Applying two coats of putty & two coats of primer of approved

brand and manufacture on new wall surface to give an even shade

including thoroughly brushing the surface free from mortar

dropping and other foreign matter and sand papered smooth. 4213.00 40.19 Smt

66 Wall painting (two coats) with plastic emulsion paint of approved

brand and manufacture on undecorated wall surface to give an

even shade including throughly brushing the surface free from

mortar droppings and other foreign matter and sand papered

smooth.- in wall 3049.00 82.03 Smt

67 Wall painting (two coats) with plastic emulsion paint of approved

brand and manufacture on undecorated wall surface to give an

even shade including throughly brushing the surface free from

mortar droppings and other foreign matter and sand papered

smooth.-in Ceiling 1164.00 87.50 Smt

68 Applying One coat of exterior primer of approved brand and

manufacture on new wall surface to give an even shade including

thoroughly brushing the surface free from mortar dropping and

other foreign matter and sand papered smooth. 1930.00 28.00 Smt

69 Finishing Wall with Weather Proof Exterior Emulsion Paint APEX

type on Wall Surface (Two Coats) to give an required shape even

shade after thoroguhly brushing the surface to remove all dirt, and

remains of loose powdered materials etc. complete 1930.00 119.07 Smt

70 Providing and fixing in position callapsible steel shutters with

vertical channels 20 x 10 x 2 mm braced with flat iron diagonals

20 x 5 mm size with top and bottom rails of T_rin 40x 40 x 6 mm

with 38mm dia, steel pulleys complete with bolts, nuts, locking

arrangements, stoppers handles including applying a priming coat

of read lead paint. 7.00 6056.03 Qntl

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

71 Providing and fixing rolling shutters of approved make made of

mm wide M.S. laths inter-locked together through their entire

length and jointed together at the ends by end locks mounted on

specially designed pipe shaft with bracket plates, guide channels

and arragements for inside and outside locking with push-pull

operation including the cost of hood cover and spring etc.

complete.(A) Shutters having width below 3.5 M. 5.00 3519.21 Smt

72 Providing & Fixing of ISI approved quality hydraulic door closer

as directed.Supply & fixing to doors & windows, ventilators, cup

boards following fixtures & fastenings of approved quality with

wooden or metal screws, nuts & bolts as directed or as per the

drawing & specifications. 23.00 925.00 Nos.

73 Supplying and fixing to doors of approved quality with wooden or

metal screws, nuts and bolts as directed-

MS CP handle 150 mm long 15.00 115.00 Nos.

74 Supplying and fixing to doors of approved quality with wooden or

metal screws, nuts and bolts as directed

-MS CP door stay double leg 15.00 75.00 Nos.

75 Supplying and fixing to doors of approved quality with wooden or

metal screws, nuts and bolts as directed-

Tower Bolt ( Stainless steel ) - 150MM long. 15.00 100.00 Nos.

76 Supplying and fixing to doors of approved quality with wooden or

metal screws, nuts and bolts as directed-

S.S best Chromium plated Aldrop - 12MM dia. & 200MM long. 15.00 290.00 Nos.

77 Supplying and fixing to doors of approved quality with wooden or

metal screws, nuts and bolts as directed-

S.S best Chromium plated Aldrop - 16MM dia. & 300MM long. 15.00 380.00 Nos.

78 Suuply & Fixing to doors of approved quality -Brass C.P. Mortise

Lock( standard Make) with Handle of approved quality 34.00 1200.00 Nos.

79 Providing & Fixing readymade P.V.C. water tight storage tank

made from linear low density polyethylene & low density

polyethylene LDPF product confirming to I.S: 10146 1982 with

cover including providing & fixing one 20mm.dia. Float valve ball

cock etc complete. 13000.00 3.91 Ltr.

80 Providing,layng and jointing in true line and level 15mm dia.

U.P.V.C pipe(SCH-40)for cold water including fitting as approved

by Engineer in charge. Pipe shall be fixed on the wall with the help

of clamp at every two meter c/c or shall be concealed as directed

including necessary fittings etc. Including testing of ppe and joints

and fixing the same with adhesive solvent, Including cost of all

materal (A) 15mm 39.00 71.93 Rmt

81 Providing,layng and jointing in true line and level 15mm dia.

U.P.V.C pipe(SCH-40)for cold water including fitting as approved

by Engineer in charge. Pipe shall be fixed on the wall with the help

of clamp at every two meter c/c or shall be concealed as directed

including necessary fittings etc. Including testing of ppe and joints

and fixing the same with adhesive solvent, Including cost of all

materal -25mm dia. 155.00 90.93 Rmt

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

82 Providing,layng and jointing in true line and level 15mm dia.

U.P.V.C pipe(SCH-40)for cold water including fitting as approved

by Engineer in charge. Pipe shall be fixed on the wall with the help

of clamp at every two meter c/c or shall be concealed as directed

including necessary fittings etc. Including testing of ppe and joints

and fixing the same with adhesive solvent, Including cost of all

materals.....32mm dia. 50.00 117.97 Rmt

83 Providing,layng and jointing in true line and level 15mm dia.

U.P.V.C pipe(SCH-40)for cold water including fitting as approved

by Engineer in charge. Pipe shall be fixed on the wall with the help

of clamp at every two meter c/c or shall be concealed as directed

including necessary fittings etc. Including testing of ppe and joints

and fixing the same with adhesive solvent, Including cost of all

materal.......50mm dia 40.00 193.73 Rmt

84 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge compression type

fittings, wall clipsetc. including making good the wall ceiling and

floor.(C) 32mm 42.00 122.22 Rmt

85 Providing, laying and jointing in true line and level 110 diametre

U.P.V.C (Type B) conforming to IS 13592-1992 with one end

plain and other end socketed with rubber ring, & fittings

conforming to ISI 14735-1999 of approved make for drainage

system pipe line, pipe shall be jointed with each other with rubber

lubricant, pipe shall be fixed on wall using of PVC clamp of the

size 110 mm diametre x 149 mm length x 145 mm heigh at every

2000 mm center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including

testing of pipes and joints and jointed with adhesive solvent

cement including cost of all materials. 39.00 868.22 Rmt

86 Providing & Fixing Single Hole Table Top Wash Basin of

minimum size 470 x 360mm on 24"X4'6" Granite Slab/support

with C.I or M.S. brackete & M. I . fisher union, P.V.C water pipe

with Connection from Stop Cock to Pillar Tap, PVC Bottle Trap

with Connection 32mm dia. C.P. brassa waste coupling etc.

Complete. Rate are inclusive of all matreials, Labour & Necessary

Fittings etc. Complete as per Detailed Drawings, Specifications

and as per the Instruction of Engineer In charge. The Model &

Make of Table Top Wash Basin Shall be as per the below Make

Company 1. Johnson, Model- Ruby (P0414PW0022)

2. Hindware, Model- Charm Cat. No.: 91239 6.00 9501.11 Nos.

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

87 Providing & Fixing Single Hole Table Top Wash Basin of

minimum size 370 x 310mm on 18"X24' Granite Slab with C.I or

M.S. brackete & M. I . fisher union, P.V.C water pipe with

Connection from Stop Cock to Pillar Tap, PVC Bottle Trap with

Connection 32mm dia. C.P. brassa waste coupling etc. Complete.

Rate are inclusive of all matreials, Labour & Necessary Fittings

etc. Complete as per Detailed Drawings, Specifications and as per

the Instruction of Engineer In charge. The Model & Make of Table

Top Wash Basin Shall be as per the below Make List.

Company 1. Johnson, Model- Ruby mini P0412MPW03SB

2. Hindware, Model- TOZZO Cat. No.:

88 Providing and fixing Gun metal check or non-return full-way

wheel valve. [D] 25MM dia. 13.00 416.47 Nos.

89 Providing and fixing Gun metal check or non-return full-way

wheel valve. [D] 32MM dia. 1.00 311.61 Nos.

90 Providing & Fixing approved best quality I.S.S approved heavy

PVC Half turn valve 50mm.dia. Valve. 2.00 2000.00 Nos.

91 Providing & Fixing Urinal of 510mm length, having concil top

inlet and bottom outlet connecting with P.V.C water pipe, 32mm

dia. C.P. brassa waste coupling with Connection 32mm dia waste

Pipe etc. Complete. Rate are inclusive of all matreials, Labour &

Necessary Fittings etc. Complete as per Detailed Drawings,

Specifications and as per the Instruction of Engineer In charge.

The Model & Make of Urinal Shall be as per below Make List.

Company 1. Johnson, Model- ARCHI URINAL P4319PW0704

2. Somany Model- OBLO Urinal 6.00 5446.16 Nos.

92 Providing & fixing water closet squatting Pan ( INDIAN type) size

580mm including P or S trap 3.00 1330.94 Nos.

93 Providing & Fixing Wall hung WC with UF seat cover, PVC Flush

Tank & intergal "P" Trap including Jointing the Trap with Pan

and Soil pipe. Wall hung shall be fixed on S.S heavy duty rack bolt

having 16mm dia, 165mm length using Plastic sleeve Make by

Using Drill Bitt Only. Rate are inclusive of all matreials, Labour &

Necessary Fittings etc. Complete as per Detailed Drawings,

Specifications and as per the Instruction of Engineer In charge.

The Make of Wall Hung Shall be from Johnson, Hindware, CERA,

Vermora or equivalent. 15.00 10948.00 Nos.

94 Providing and fixing C.P. brass towel rail comlete with C.P. brass

brackets fixed to wooden plugs with C.P. brass scews.(B) 600mm

x 20mm size. 12.00 610.32 Nos.

95 Providing & Fixing Health Faucets (ABS Body) SS braided

connection pipe. Rate are inclusive of all matreials, Labour &

Necessary Fittings etc. Complete as per Detailed Drawings,

Specifications and as per the Instruction of Engineer In charge.

Make of Health Faucets Shall be any SS braided pipe models of

Johnson/Hindware/Cera or equivalent. 12.00 1265.00 Nos.

96 Providing & fixing PVC SWR nahni trap IS 14735 for drain -75

mm diameterr with Jali of the following nominal diameter of self

cleansinf design with CI scread down of higed grating including

the cost of cutting and making good the walls. 30.00 568.89 Nos.

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

97 Providing & Fixing 15mm C.P. Pillar cock 15 mm Heavy duty

swan neck of make jaguar, hindware, cera or equivalent. Rate are

inclusive of all matreials, Labour & Necessary Fittings etc.

Complete 12.00 795.00 Nos.

98 Providing & Fixing 15mm One way Bib Tap with Wall Flange

make jaguar, hindware, cera or equivalent. Rate are inclusive of all

matreials, Labour & Necessary Fittings etc. Complete. 18.00 514.00 Nos.

99 Providing & Fixing 15mm C.P. Angle stop cock Heavy duty with

cap make jaguar, hindware, cera or equivalent. Rate are inclusive

of all matreials, Labour & Necessary Fittings etc. Complete. 42.00 521.00 Nos.

100 Providing and fixing S.W Gully trap with C.I Grating brick

masonary chamber and water tight C.I cover with frame of

300MM x 300MM size (inside) with standard weight. [I] Square

mouth traps. [B] 150MM x 100MM size 'P' or 'R' type. 4.00 1234.57 Nos.

101 Providing B.B. Masonry inspection chamber (MANHOLE) of

approved size including light type C.I. Cover with frame,

necessary excavation bottom concreting of .C.C. (1:3:6) 150mm.

thick/ 225mm. thick B.B. Masonry in C.M.(1:6) 12mm thick

cement plaster in C.M.(1:3) inside & to all exposed faces up to

450mm. below ground level, curing etc., 300X300 mm including

disposal off surplus excavated earth up to radius of 300 mt.

including 3 coats of white or colour wash to all exposed finished

surface etc. complete as directed by E.I.C., with free supply of

cement by the Board (B.B.MASONRY UPTO 1000mm. DEPTH.)-

300 x 300 clear size 2.00 4161.00 Nos.

102 Providing B.B. Masonry inspection chamber (MANHOLE) of

approved size including light type C.I. Cover with frame,

necessary excavation bottom concreting of .C.C. (1:3:6) 150mm.

thick/ 225mm. thick B.B. Masonry in C.M.(1:6) 12mm thick

cement plaster in C.M.(1:3) inside & to all exposed faces up to

450mm. below ground level, curing etc., 450X610 mm including

disposal off surplus excavated earth up to radius of 300 mt.

including 3 coats of white or colour wash to all exposed finished

surface etc. complete as directed by E.I.C., with free supply of

cement by the Board (B.B.MASONRY UPTO 1000mm. DEPTH.)-

-450X610 mm clear size 6.00 5660.00 Nos.

103 Providing & fixing to wall, ceilling, and floor in plumb by means

of GI clamps of 18 gauge sheet with 1 to 1.5 mtrs. Distance PVC

6.00 Kg. /cm2 working pressure polythene pipes of approved

brand incl. joining with approved solution & all fittings like bend,

tee. Y bend plug bend with water tight jointsIf pipe laid in

trenchesscope - 90 mm Dia. 20.00 227.00 Rmt

104 Providing & fixing to wall, ceilling, and floor in plumb by means

of GI clamps of 18 gauge sheet with 1 to 1.5 mtrs. Distance

Kg. /cm2 working pressure polythene pipes of approved brand

incl. joining with approved solution & all fittings like bend, tee. Y

bend plug bend with water tight jointsIf pipe laid in trenchesscope -

75mm Dia. 40.00 277.46 Rmt

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

105 Providing & fixing ISI brand PVC rigid pipe for sanitary

connection (SEWER DRAIN PIPE) with necessary slope including

excavation refilling the trenches, providing filling the joints with

solution etc. completed.- 110 mm. dia. 10 Kg./Cm 2 59.00 335.69 Rmt

106 Providing, laying and jointing in true line and level 160 diametre

U.P.V.C (Type B) conforming to IS 13592-1992 with one end

plain and other end socketed with rubber ring, & fittings

conforming to ISI 14735-1999 of approved make for drainage

system pipe line, pipe shall be jointed with each other with rubber

lubricant, pipe shall be fixed on wall using of PVC clamp of the

size 160 mm diametre x210 mm length x 196 mm heigh at every

2000 mm center to center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including

testing of pipes and joints and jointed with adhesive solvent

cement including cost of all materials. 10.00 826.12 Rmt

107 Providing & Fixing light type C.I. Manhole covers with water tight

C.I. Frame & fixing the same in concrete etc., complete as directed

by E.I.C. 600mm x 450mm size not less than 35 kg.

108 Providing & Fixing 450X600X6mm. thick size approved best

quality of looking glass mirror Modi or gold fish, mounted on

6mm thick ply with edging with PVC angle patti as directed with

fixture as required.

109 Providing and Fixing SS 304 Grade Handle of 230 mm long as

directed by EIC 18.00 575.00 Nos.

110 Providing 2500mm internal diameter & 3.0 Mt. Deep soak pit

including excavation in all types of soil & soft rock & CC(1:3:6)

bedding, 300 mm thick below masonry and 450mm thick B.B

Masonry in CM(1:6) up to 600mm height, 350mm thick for further

600mm and 230mm thick for remaining height honey combed,

plastering in CM(1:3) outside up to 1.5 Mt height and 100mm

thick M200 RCC slab with 600x600mm C.I.HEAVY duty cover

with frame, with necessary reinforcement as per design & C.I Vent

pipe 1800mm long with B.B masonry pillar 350x350x450

plastered all around filling with 40 to 50mm size brick bats up to

1.5 Mt depth, including 16mm dia M.S’U’ shape steps, refilling

including disposal of the surplus excavated earth up to the lead of

500mt. Radius including 3 coats of white or colour wash to all

exposed finished surface etc. complete as directed by E.I.C.

111 Providing & fixing steel cupboard shutter of 20 gauges with steel

frame and fixing the frame with brick masonry including locking

arrangement with 3 coats of approved oil paint etc., complete. 286.00 3730.00 Smt

112 Providing and fixing precast rubber dye inter locking concrete

block 60mm thick with grade of concrete M-200 pnumatic

comressed by mechanically pressed and as per approved design

including 75mm sand layer for levelling and filling the joint with

sand in proper line and level etc comp as per directed. 723.00 603.00 Smt

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

113 Providing and fixing pre-cast concrete Kerb stone of grey cement

based concrete block 30 cm length, 30cm height and 15cm thick of

M-250 grade concrete as per approved design and including

excavation for fixing in proper line and level, filling the joint with

C.M. 1:3 ( 1-Cement : 3-Sand ) etc complete as directed by EIC.

114 Providing and fixing single layer waterproof gypsum board 8mm

thick of the make newgood group co.ltd or equivalent & newgood

group co ltd company section using waterproof board of size

1220mm x 1830mm x 8.0mm suspended by GI suapender of size

25mm x 3mm with intermediate channel of size 18mm x 40mm x

0.80mm at 1220mm C/C ceiling section of size 40mm x 35mm x

0.55mm at 457 mm center to center and perimetre chanel A of size

20mm x 27mm x 30mm x 0.50mm at edges & drops including

paper tap sand sofit cleat anchor fastener scoch bolt connecting

cleat joining compound top coat on ceiling including making

necessary opening for light fitting,diffuser etc..compete as per

detail drawing as directed. 110.00 600.94 Smt

115 Providing and fixing gypsum board decorative Stepping of

approved shape and size as per requirement of site situation

including required structure including all necessary fixing. 134.00 261.00 Rmt

116 Providing and fixing structural glaze panels on brick/ concrete

walls for exterior glazing with coloured anodized frame section

having size 63.50 x 38.10 x 1.95mm with web fix in powder

coated MS clamps with SS nuts-bolts as per design and sticking

antiglare coloured 5mm thick glass [glover bell, Belgium or equi.]

using spacer taps structural silicon sealants GE - SSG 4000 and

making waterproof and shockproof etc including labours,

scaaffolding, all accessories as per architechtural drawings detail

etc. complete as directed by Engineer Incharge. 59.00 3285.00 Smt

117 Providing and fixing Alco Pennel Ceiling made up of on either

side laminated with ACP of 3 mm thick with appropriate shape

fixed with 2 mm thick Alliminium Section appropriate size with

Locking arrangement , Door Stop and selling with Silicon & Birla

3 m Tape , Hardwer and etc. complete as directed by EIC. 163.00 2950.00 Smt

118 Providing and fixing 304 Grade Stainless Steel railing having

mm dia, hollow stailess steel pipe hand rail and 40 mm dia.

Hollow stainless steel pipe with combination of 10 cm long 20 mm

dia pipe as vertical support with 20 mm dia hollow pipes 3 rows as

intermidiate members running throughout with steel bol as cap at

each end including cutting, bending, welding & fabrication the

structure as per drawing in 404 grade of steel etc. completed as per

instruction. 26.00 3135.00 Rmt

119 Providing and fixing Stainless Steel letters/symbol of any size in Per

approved steel grade SS 304, including all fastners and fixtures & inch

scaffolding, labours etc. at given location and any height as per

directed by EIC 1947.00 85.10 letter

120 Providing & Fixing Fencing using 30x30 MS Pipe 1.50m x 1.50m

Covered with 8 Gauge Wire Square Jali of Approved

Quality,icluding material,labour,transport etc as directed by EIC. 23.00 890.00 Smt

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

121 Providing & Fixing Approved Quality of ACP Sheet Sign Board

with Acrylic Word (Double step) of Sub Division/Division Office

with Canopy at Border incl. Transportation, Electrical Lighting,

Material, Fitting etc. as Per Directed by EIC. For More than 10 Sq.

ft Size 60.00 1250.00 Sft

122 Providing & Fixing Approved Quality of ACP Sheet Sign Board

with Radium Word of Sub Division/Division Office incl.

Transportation, Material, Fitting on wall using SS Stud etc. as Per

Directed by EIC. For More than 10 Sq. ft Size 45.00 541.00 Sft

123 Providing and Fixing 100% blackout waterproof window curtains

with corded roll up and down blinds over heavy duty roller tube

with chain rolling system including all labour and Material as

directed by EIC 154.00 1050.00 Smt

Estimated Cost Section-I (CIVIL WORKS) in Rs.

124 (A) GENERAL DESCRIPTION OF LIFTS.

Supplying, Erecting, Testing & Commissioning the passenger/stretcher lift having following

[1] GEAR LESS LIFT DRIVE (MRL) comprising of High Starting torque Lift 3 phase 440 V A.

Permanent Magnet Synchronous motor of proper rating with high efficiency shall be used.

[2] Micro processor based / PLC, ACVVVF, vector control drive with encoder feedback closed

loop system shall be used for lift car and door operation which shall be full collective selective

operation hall call demand response, UP/DOWN hall stops, Main, Up/ Down Contactor with

overload and phase reversal relay and safety controls.

[3] Car with M S platform with bracings of adequate size and to sustain the impact load cabin

+ passenger with safety factor of fire for steel and side panels of Stainless steel of sheet of grade

304 duty. Car ceiling will be S.S. finishes with aesthetic appearance with LED ceiling lights.

Car flooring shall be of anti skid PVC with choice of colour of engineer in charge. Car doors

shall be of stainless steel grade 304, hairline finish with centre opening / telescopic automatic

doors. Car panel will also be S.S. 304 finished with emergency stop device, mechanical door

safety device, facility of auto/ attended mode. All car panel buttons and all floor switches must

be with brail language as per lift act.

[4] All landing doors must be fire rated for 2 hour shall be fully automatic centre opening/

telescopic opening made of hairline finish steel grade of 304 with key holes and infrared curtains

with Unlocking facility from outside

[5] Appropriate battery operated emergency light in the car along with alarm switch shall be

provided. Also, Emergency Light & Fan should start immediately without any Time Delay as

soon as power fails.

[6] Digital scrolling indicator system for up-down arrow along with floor position indicator

shall be provided inside the car and at all floors.

[7] Full height infra red curtain with multiple cross / crossing light beams shall be provided.

[8] Automatic Rescue Device (ARD) shall be provided accordingly of passenger capacity with

Manual Rescue Operation ( Manual Cranking Facility).

[9] Audio visual indication in the lift car showing over loading shall be provided such that doors

kept open till excess load is removed.

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

[10] Spring buffers/PU Buffers shall be provided.

[11] Car fan as per passenger capacity with automatic sleep timer shall be provided.

[12] Voice annunciator with suitable music shall be provided in lift car.

[13] Self diagnostics system for operational and safety parameters shall be provided in

[14] Mechanical over speed governor with governor calibration as per actual site parameters

and submission of calibration certificate submission, door key holes in the floor doors, fireman

switch shall be provided.

[15] Lift machine hoisting arrangement in the lift machine room and monkey ladder for lift pit

should be provided by the lift agency, along with the other steel structure works, foundations for

the machine etc…

[16] In the hoist way fascia plate shall be provided without any extra cost, where ever required as /

if directed by engineer in charge.

[17] Permanent wiring with necessary safety devices like RCCB in all circuit, Over Voltage

Under Voltage protection and THD eliminator in circuit for lift machine room and lift well

with proper numbers of light points, with fixtures, exhaust fan and plug points shall be

provided by the agency. Only 3 phase Power Supply shall be made available by department in

lift machine room. Necessary Earthing as per Lift Act/Rules shall be arranged by Lift

[18] Any civil/ electrical works for additional and alteration in lift shaft and machine room

related to erection of lift shall be made by lift agency without any extra cost. (granite/marble fixing

around all landing door openings are not in lift agency’s scope.)

[19] Agency has to provide all working drawings and documents and liaison services for

obtaining all necessary permission from lift inspector and other authorities.

[20] acrylic transparent licence/display A4 size holder in lift car.

[20A] As per statutory requirement of Govt. Of Gujarat lift & escalator act 2000, lift agency has to

1. Car top safety barricade

2. Push & talk communication system.

3. Fireman's switch operation at Ground Floor.

4.carrying out third party lift inspection during/after lift erection and provide report by third party

authorized by concern licensing authority

5.agency has to provide third party insurance upto completion of free maintenance period and

submit the document for the same. [21] Car Panel Operating Buttons with floor position

indicator/buttons must be of Auto Glow type clearly visible when view from inside cabin.

[22] For Physically Handicapped person Full Length Handrails of hairline finish steel grade of

should be provided at appropriate height on the Rear & Side Wall Panels in Lift Car.

The Rates of this item is for the lift of Machine room less. For Machine room Lifts, rate for Rs.

1,50,000/- shall be deducted in Total Cost for this Lift.

8/10 Passengers, Ground plus 2 upper floors with Rated Speed

of 1.0 m/sec. (B) With General Specification of Cat.III

Estimated Cost Section-II (LIFT) in Rs.

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

125 Main Fire Hydrant Pump LUBI/KSB/KIRLOSHKER make SITC

of: Back pull out type -Single Stage, Self Mriming, Centrifugal

Pump for Main Fire Pump with Electric Motor, Meachanical Seal,

Base frame and Couplings. MOC:-Casing-CI, Impeller- Bronze,

Shaft- SS 410, Sleeve- SS410. Flow Capacity: 450 LPM Head:

to 35 mtr 2900RPM Pump shall be capable of furnishing not less

than 150% of rated capacity at a head not less than 65% of rated

head he shut off head shall exceed 120% of rated head. UOM:-

Price Per Complete set of Pump + Motor + Accessories.

126 Supplying & erecting approved control cubical panel (Star - Delta)

made from16 G. CRCA sheet duly painted with epoxy powder

painted inside and outside with hinged doors and locking

arrangement, consisting of suitable size of ON- OFF isolator (AC -

3/23 duty) main fuses, single phasing preventer cum water level.

Guard (Complete unit), Toggle switch to by pass Single phase

preventer cum WLG, indicating lamps for R- YB phases, over load

relay, Automatic water level controller, Ammeter & Voltmeter

each with two way selector switch incoming wires duly socket

Crimped, Panel to be erected on angle iron frame grouted on wall

as directed. Star Delta & main contactor, overload relay, thermal /

Electronic Star delta cutoff timer, start - stop push buttons. The

isolator overload relay & contactors of L& T, Siemens, Redex or

Cuttler Hamer make only. Panel to be erected on angle iron frame

ground on wall.make-Sky/Belife/L&T 1.00 24865.00 Nos.

127 Piping for Fire Safety Works Providing & Laying 'C' Class Heavy

G.I. pipe laying. Supply, fabrication, installation, hydro testing &

painting of above ground pipe. with necessary pipe itments

(Flanges, Bands, Socket etc.) Vertically every 3 mt. & Horizontaly

every 2.5 mt. painted with one coat of primer (Zinc Oxide) & two

coats of finshing paints GI support / Clamps / Hangers/pipe etc.

Hardware (Gaskets, Nut-Bolts, Paint etc.) Consumables (Welding

Rod etc.) and labour charge. Quality : GI, C-Class (Heavy). Make -

Apollo/Surya prakash / Asian Note : The piping installation has to

be put to hydraulic test to1.5 times Working pressure before

applying paint or pipe coating and wrapping etc.

Complete.................100 mm diameter 36.00 1960.00 Rmt

128 Piping for Fire Safety Works Providing & Laying 'C' Class Heavy

G.I. pipe laying. Supply, fabrication, installation, hydro testing &

painting of above ground pipe. with necessary pipe itments

(Flanges, Bands, Socket etc.) Vertically every 3 mt. & Horizontaly

every 2.5 mt. painted with one coat of primer (Zinc Oxide) & two

coats of finshing paints GI support / Clamps / Hangers/pipe etc.

Hardware (Gaskets, Nut-Bolts, Paint etc.) Consumables (Welding

Rod etc.) and labour charge. Quality : GI, C-Class (Heavy). Make -

Apollo/Surya prakash / Asian Note : The piping installation has to

be put to hydraulic test to1.5 times Working pressure before

applying paint or pipe coating and wrapping etc.

Complete.................80 mm diameter 6.00 1594.00 Rmt

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

129 Pressure Switch with Siphon Tube and Cock. Supply, Installation

and Testing of: Pressure Gauge with Siphon Tube and Cock.

MOC:-100 mm Dial- Glycerin filled- Stainless Steel Body

Pressure Gauge with GI Siphon Tube and Brass Cock. Size:-Dial:

100 mm Range: 0 – 15 Bar (kg/cm2) for 100 mm make-

Danfoss/Orion/Indfos 1.00 1780.00 Nos.

130 Pressure Gauge with Siphon Tube and Cock. Supply, Installation

and Testing of: Pressure Gauge with Siphon Tube and Cock.

MOC:-100 mm Dial- Glycerin filled- Stainless Steel Body

Pressure Gauge with GI Siphon Tube and Brass Cock. Size:-Dial:

100 mm Range: 0 – 15 Bar (kg/cm2) for 80 mm make-Airmaster/H

guru/Fiebig 1.00 1535.00 Nos.

131 NON- Return Valve Dual Plant Supply, Installation and Testing of

conforming to IS: 5312 complete with rubber gasket, GI bolts,

nuts, washers etc. as required with necessary pipe fitments,

hardware and consumables. MOC:-Body: SS.plate SS

100 mm dia make-Zolato/Kartar/Osko 1.00 8756.00 Nos.

132 Air Release Valve- 25 mm

Supply, Installation and Testing of: Air Release Valve Check

Valve with necessary pipe fitments, hardware, union and

consumables and Ball Valve assembly on top of each riser for Air

release system. MOC:-Body: Gunmetal / SS. Make-ISI 1.00 1780.00 Nos.

133 Fire Hydrant Landing Valve IS 5290 (Stainless Steel (SS-304), ISI

Marked): Supply, Installation and Testing of: Fire Hydrant

Landing Valve with necessary pipe fitments, hardware and

consumables. Stainless steel 63 Female single outlet type –

“A“Hydraulic,Test : 21 Kgf/cm2 202 working parts, Water Test :

Water tightness 14kgf/cm2, Flow Test : 900 LPM at 7 kgf/cm2,

MOC:-Body: Stainless Steel (SS-304), Working Parts: Stainless

Steel (SS-304), Coupling: Stainless Steel (SS-304), Standard: -ISI

Marked. Size:-63 mm (Flange End: NB 75 mm, PCD 160 mm)

MAKE : Newage/Aaag/Sangam 3.00 4265.00 Nos.

134 Fire Hose reel drum Ahemdabad type IS 884 25 mm x 30 m

Supply, Installation and Testing and commisoning: ISI 884. With

Thermoplastic pipe with SS Shuttoff Nozzle. Standard: - ISI

Marked & TAC Approved Hose. Size:-25 mm dia x 30 m long .

MAKE : Newage/Sangam/or eqvalant 3.00 3890.00 Nos.

135 Fire Hose pipe type A Is 636 and male female coupling intenseous

SS 304 with GI binding legth 15mtr complete set . MAKE :

Newage/Sangam/or eqvalant 6.00 3675.00 Nos.

136 Cabinet For Fire Hose (Hose Box)- Double door Type Supply,

Installation and Testing of: Fire Hose Cabinet (Hose Box) suitable

to accommodate 02 no. of 15 m long fire hoses and 01 no. of

nozzle. With Lock-n-key facility. Wall Mounting Design. MOC:

18 Gauge MS Box with Powder Coating Standard with Size. 3.00 2865.00 Nos.

137 Short Branch Pipe IS 903 Conforming Nozzle. Supply, Installation

and Testing of: Short Branch-pipe Nozzle. MOC: Stainless Steel

(SS-304). Standard: ISI Marked, Heavy Quality. Test : 21 Kgf/cm2

No. MAKE : Newage/Aaag/Sangam 3.00 1780.00 Nos.

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

138 Supply Installation and commisioning of 25mm Brass Ball valve

for connection of hose reel thermoplstic pipe make-

Zolato/Venus/Sant 3.00 980.00 Nos.

139 Butterfly Valve 100mm Dia IS

Providing fixing testing and commissioning of SS. Butterfly valve

of class PN 1.6 rating of following sizes. dia, Sant brand.(I.S.I)

MOC:-Body: SS, Disk: SS, Seat: Nitrile.Make Zolato/Kartar/Osko

140 Fire Service In-let (In-let Connection for Fire Brigade)-2 Way

Type. Supply, Installation and Testing of: Fire Service Inlet with

necessary hardware and consumables. MOC:-Body: Heavy- uty

CI. Couplings/NRV:SS Standard: -Made As per IS Standard-

Heavy duty quality. Size:-Couplings: 63 mm, 100 mm E-table

Flange End . 1.00 3240.00 Nos.

141 Providing, Installation and Testing Fire extinguisher IS 15683-

2006 ISI marked BIS with Peso 3 years ABC powder type 6 Kg.

Supply, installation and testing of ABC powder fire extinguisher

necessary hardware and consumables. Stored pressure mechanism.

Charged with MAP-50% (ABC) Dry powder. with wall mounting

clamp.Make -V Safe/ Kanex /Ceasefire

142 Providing, Installation and Testing of Fire extinguisher - CO2 Gas

type 4.5 kg. Supply, installation and testing of CO2 Gas fire

extinguisher with necessary hardware and consumables. Standard -

Confirming to IS:15683-2006 with ISI mark with Peso 5 years

certified. Make - V-Safe/Kanex / Ceasefire 5.00 4275.00 Nos.

143 Providing and fixing AUTOGLOW Signages in Block / Small

Letters of Specified Sizes: as per design and requirement as

directed by EIC. 15.00 185.00 Nos.

144 Providing and fixing, testing and commissioning of Conventional

Fire Alarm control panel for G+2 building 2 zones required as per

engineer insruction with wiring complete fittings Make:

Ravel/agni/or equivalent 1.00 16256.00 Job

145 Providing and fixing, testing and commissioning of Hooter with

wiring complete fittings Make: Ravel/agni/or equivalent 3.00 3240.00 Nos.

146 Providing and fixing, testing and commissioning of ON OFF

Switches with wiring complete fittings Make: Ravel/agni/or

equivalent 3.00 1865.00 Nos.

147 Providing and fixing, testing and commissioning of Manuel Call

point with wiring complete fittings Make: Ravel/agni/or 3.00 2915.00 Nos.

148 Making of hole by core cutting in concrete member or masonary

wall of diameter 0 to 200 mm as per requirement including all man

material and charges of core cutting machinery as directed by EIC 5.00 700.00 Nos.

149 Charges Fire drawing, consulting and certification process &

administrative fees for obtaining Fire NOC from concern

department with all the requried documents and process and

providing fire system annual maintenance service contract for

keeping operational the fire safety system in all respect for three

(3) years & providing mockdrill, awarness traning for staff as per

rules of fire at every 6 months as per GOG NBC Fire norms. 1.00 50000.00 Nos.

Estimated Cost Section-III (FIRE SAFETY WORKS) in Rs.

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

150 Point wiring with approved ISI marked 1.1 KV grade 2 X

sq.mm. copper PVC insulted FRLS wire with 1.5 sq.mm. (green)

copper PVC insulated FRLS wire for earth continuity in FIA

approved ISI mark medium class white colour 20/25 mm dia.

embossed rigid PVC pipe with PVC fitting fixed with adhesive

solution erected in/on brick wall / slab along with continuous G.I.

fish wire to draw wires and laid in approved manner zari for PVC

pipe and boxes shall be filled with cement mortar and finishing the

surface to match the wall / ceiling complete with approved make

5/6 Amp. ISI mark modular type switch and accessories mounted

in 20 G. G.I. company fabricated metallic box covered with

appropriate front plate modules erected flushed with wall / ceiling

with necessary modular lamp holder / modular ceiling rose / HD

Connector as directed for concealed wiring (a) Light point. Cat.-

Necessary sheet / tape / polythene / sand must be erected or filled

in all box to prevent mortar going into the box. Length of point

wiring must not increase than 10 mtr. For that necessary switch

boards and their locations must be finalised before execution by

agency otherwise payment will not be done for extra long point.

(For future extention, if required, agency has to erect one higher

size metal box and modular plate as per instruction of EIC. Cost of

blank plate shall be paid as per tender item) [Wire must be having

box packing][This item include cleaning(inside/outside) of all GI

switch boards,electric point box,fan box,MCBDB & box cutting

plaster finishing for modular plate without any gap]

151 Two way controlled light point, Cat.-III 8.00 616.00 Point

152 For Bell Point, Cat.-III 12.00 495.00 Point

153 For Fan Point (with 6 A. Modular type switch and two module

hum free EME Five step type Electronic fan regulator both having

ISI mark) Cat.-III 119.00 695.00 Point

154 Two way controlled Fan point (with 6 A. Modular type two way

switch and two module hum free EME Five step type Electronic

fan regulator both having ISI mark) Cat.-III 3.00 816.00 Point

155 For separate Point (with 6 Amp. Switch & 3/5 pin socket both

having ISI mark) Cat.-III 5.00 523.00 Point

156 For Looped on switch board (with 6 Amp. Switch & 3/5 pin

socket both having ISI mark) Cat.-III 65.00 266.00 Point

157 Providing and erecting Medium Class FIA approved and ISI mark

white colour (embossed) RIGID PVC PIPES of following size

complete erected with necessary PVC fittings & Junction boxes

fixed with adhesive solution & clamps on / in wall / ceiling along

with continuous fish wire to draw mains with necessary fittings

and junction boxes for following dia. (a) 20 mm. dia. 420.00 26.00 Mtr.

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

159 Providing and laying Mains with FRLS PVC Insulated wire ISI

marked 1.1 KV grade with FIA approved ISI mark medium class

20/25/32 mm dia. embossed rigid PVC pipe with PVC fitting fixed

with adhesive solution to be erected on/in brick wall / slab along

with continuous G. I. fish wire to draw mains laid in approved

manner with plastering by cement mortar & finishing the surface

to match the wall / ceiling complete with FRLS PVC insulated

wire for earth continuity. (Approved ISI make only) [a] 2 x

sq.mm. FRLS copper multi stranded conductor mains with

sq.mm. FRLS copper multi stranded conductor for earthing as per

standard colour code. (with 20 mm dia. PVC pipe) [Wire must be

having box packing] 2000.00 68.00 Mtr.

160 2 x 2.5 sq.mm. FRLS copper multi stranded conductor mains with

1.5 sq.mm. FRLS copper multi stranded conductor for earthing as

per standard colour code. (with 20/25 mm dia. PVC pipe) [Wire

must be having box packing] 2100.00 90.00 Mtr.

161 2 x 4.0 sq.mm. FRLS copper multi stranded conductor mains with

2.5 sq.mm. FRLS copper multi stranded conductor for earthing as

per standard colour code. (with 20/25 mm dia. PVC pipe) [Wire

must be having box packing] 200.00 123.00 Mtr.

162 2 x 6.0 sq.mm. FRLS copper multi stranded conductor mains with

2.5 sq.mm. FRLS copper multi stranded conductor for earthing as

per standard colour code. (with 25 mm dia. PVC pipe) [Wire must

be having box packing] 200.00 162.00 Mtr.

163 4 x 10.0 sq.mm. FRLS copper multi stranded conductor mains

with 4.0 sq.mm. FRLS copper multi stranded conductor for

earthing..As per standard colour code. (with 25/32 mm dia. PVC

pipe) [Main panel to 3 Phase MCBDB] 100.00 472.00 Mtr.

164 Providing & fixing 20mm. dia. PVC insulated G.I. corrugated

Flexible pipe with necessary socket, PVC bushes saddle, Check-

nuts etc. complete of following sizes. 80.00 36.52 Mtr.

165 Providing & fixing 25 mm. dia. PVC insulated G.I. corrugated

Flexible pipe with necessary socket, PVC bushes saddle, Check-

nuts etc. complete of following sizes. 60.00 43.82 Mtr.

166 Providing and erecting Plug Point wiring with approved ISI make

2 x 2.5 sq.mm copper PVC insulated FRLS wire with 1.5 sq.mm

(green) copper PVC insulated FRLS wire for earth continuity in

FIA approved ISI mark white colour medium class 20/25 mm dia.

embossed rigid PVC pipe with PVC fitting fixed with adhesive

solution erected in brick wall/slab along with continuous G.I. fish

wire to draw wires and laid in approved manner zari for PVC pipe

& boxes shall be filled with cement mortar & finishing the surface

to match the wall / ceiling complete with 16 Amp. Modular type

Swich and accessories mounted in 20 G. G.I. company fabricated

metallic box covered with appropriate front plate modules erected

flushed with wall. (a) 16 Amp. Indicating switch & 1 No. 6/16 A

universal socket white colour suitable for 3 pin top duly both

having ISI mark. sheet / tape / polythene / sand must be erected or

filled in all box Cat.-III

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

167 Providing and erecting Plug Point wiring with approved ISI

marked 1.1 kv grade 2 x 4.0 sq.mm copper PVC insulated FRLS

wire with 2.5 sq.mm (green) copper PVC insulated FRLS wire for

earth continuity in FIA approved ISI mark white colour medium

class 20/25 mm dia. embossed rigid PVC pipe with PVC fitting

fixed with adhesive solution erected on/in brick wall / slab along

with continuous G.I. fish wire to draw wires and laid in approved

manner zari for PVC pipe & boxes shall be filled with cement

mortar & finishing the surface to match the wall / ceiling complete

with approved make 16 Amp. Modular type switch and

accessories mounted in 20 SWG G.I. company fabricated metallic

box covered with appropriate front plate modules erected flushed

with wall / ceiling. (a) 16 Amp. indicating switch & 1 No. 6/16 A

universal socket white colour suitable for 3 pin top duly both

having ISI mark. (A.C. POINT ONLY) sheet / tape / polythene

/ sand must be erected or filled in all box 5.00 906.00 point

168 Blank Plate Single. Cat.-III 60.00 28.00 Each

169 Modular Indicating Call Bell. Cat.-III. 16.00 366.00 Each

170 16/20/25 Amp. Modular Starter for Motor / A.C. Unit Complete

Cat.III 5.00 554.00 Each

171 Supplying & erecting Electronic Type Cordless Call Bell erected

on PVC/Metal board having portable bell push working on D.C. &

bell on 230V A.C. supply with cells / battery 5.00 278.00 Each

172 Providing & erecting Switch board for Computer or electric

apparatus consisting of following items in single board erected on

Metal board with 3 mm thick PC (Polycarbonet) / Acrylic sheet

erected as directed. 1 no. 6/16 Amp. universal Socket, 1 no.

Amp. international socket, 2 nos. 16 Amp. indicator switch,

nos. 6 Amp. Switch & 2 nos. 6 Amp. 5 pin Plug. For Computer

power Supply board. Cat.-III 85.00 1262.00 Each

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

173 Providing & erecting 2.0 mtr long earthing system by making min

bore of 225 mm dia in soft soil. Suitable for doing pipe in pipe

technology as per IS-3043-1987,Earthing Electrode must be made

from corrosion free hot dip galvanizing pipes having following

(A) Earthing Electrode: outerpipe:- 88 mm minimum O.D., ISI 'B '

Class of Reputed Brand, Inner pipe:- 42 mm minimum O.D., Pipe

B Class ISI reputed Brand Terminal Size: 70 mm X 100 mm

length, Terminal Should be made from inner pipe for that pipe

must be pressed and gave rectangular shape so its work as a

terminal.The hot deep galvanising must be done after above

process.Galvanised thickness must be minimum 75 micron any

where.SS , Nut bolt:- 2 no.with washer suitable for 14 mm dia hole

must be provided at terminal. total minimum Weight(approx) of

earth electrodewith inside conductive material should be

(B) Inner chemical (CCM Compound): Resistivity: 0.2 ohm/meter

testing as per ISE 62561-2017, Voltage drop:-<1 volt at no load

and dry form, Sulphar content:<2%

(C) Back fill compound:- Earthing compound should be capable to

retain moisture for 1 Year & weight (approx.) of earth electrode

with inside conductive material is 25 Kg.

Necessary test report must be submitted.

1. Short circuit test by ERDA/ CPRI for 25KA

2. Resistivity test of conducting material from NABL accredited

3. Hot dip galvanised / zinc coating micro test from reputed

4. General test report from OEM regarding specification of

[Approved Make:- Sulah safe solution, Ashlok, Galexy, Indelec,

Safex, Yansi earthlid (Strictly subject to item specification

only)]OEM has to submitted detail and sample for approved

before supplying. Water must be poured in bore before starting

earthing. earthing value must be measured with earth tester.

Agency has to bring the earth resistance to at least 02.00 Ohms &

its value during defect liablity. If required. Earthing must be done

in the presence of A.E (GSPHCL)

174 For above earthing additional charges for boring in hard rock soil

(by breaker) & filling soft soil in earth pit (certificate for soil have

to given by DEE / AE along with photographs) 7.00 325.00 Each

175 Constructing brick / CC block masonary earthing chamber

mm X 450 mm X 600 mm incuding 500 mm X 400 mm

horizontal grating with frame and cover complete (This item must

be executed by civil agency) 7.00 1532.00 Each

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

176 Supplying & erecting approved make street light box comprising

CNC Processed robust housing made FRLSom single sheet multi

folded with high grade powder coating (RAL-7032 Structure finish

as Standard) of IP-55 degree of Protection Gasket (PU Gasketing)

of following size of Box. [i] 350 mm X 200 mm X 150 mm

LIGHT FIXTURE / FAN

177 SITC Of 24 Watt LED Indoor Commercial make high efficiency

performance lamp with combination of high quality diffused

polycarbonate and aluminium base dedicated heat sink for better

performance of LED and also long life. High quality LED must be

placed on metal core printed circuit board for better heat

dissipation. separate driver with all protection like under voltage

(120 to 300), over voltage protection, 2 KV surge protection. The

life of lamp should have 25,000 hrs at L70, THD<15%, efficiency

>90 lm/w, with high power factor > 0.90, with CRI > 80, for better

color rendition total lumens should be min 2160. The lamp should

be suitable for T8 box type fitting made form CRCA sheet and

white powder coated. The data sheet of LM79 for complete lamp

can also be provided. (LT, Phillips, GRE, Havells, Pyrotech,

Orient, Ensave make and model Approved by EIC as per

Specification) (Note:-The manufacturer/ authorized Channel

partner of the manufacturer has to submit 4 yrs free replacement

Guarantee for complete Fixture) [Approval will be given strictly

subject to item specification] 140.00 480.00 Each

178 SITC of 8 W LED Lamps integral type, cool white with PC

diffuser suitable for B22 Lamp holder 800 lumens and P.F >0.9.

[Make- Bajaj, Havells, GRE] 15.00 145.00 Each

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

179 SITC of Indoor Commercial recess/surface mounted (IP20) Max.

24 w Cool white Color LED Down lighter office Lighting

Luminaire with external separate driver having BIS certification

with fully die cast aluminium alloy housing without any

PVC/Plastic part with corrosion resistant powder coated finish as

a heat sink with Poly Carbonet diffuser LED complete (only from

Philips Lumileds, CREE, BridgLux, Seoul, Nichia & Osram CRI >

80, CCT 5600K (5400 to 5800K bin). The led's should be mounted

on Metal core based PCB for better heat conduction and long life

of LED. (LM 79 for complete fixture, LM80 for individual LED

Report mustbe submitted) The fixture should have extra protection

of driver like over/under voltage, THD<15%, P.F.>0.90, for 24 w

fixture wide voltage range from 100 to 270 V, 50/60 HZ, 4 KV

surge protection.

Fixure must have Min. 2160 Lumens light output. Fixture Efficacy

should be>=90 Lumens/watt. (L70 @ 30,000 Hrs) The Fixture

should be able to easily mount on POP/Grid False cieling. The

Luminiare should be tested as per IP20 standards and following

test reports should be submittedat the time of approval. (Lighting

Technologies make, Philips make, OSRAM, Havells, Orient,

Ensave, GRE & Pyrotech Model Approved By EIC as per

Specification only) (Note:- The manufacturer/authorized Channel

partner/dealer of the manufacturer has to give a 4 yrs. free

replcement Guarantee for complete Fixture) 45.00 980.00 Each

180 SITC of Spot light of 5 W, The led's should be mounted on metal

core based PCB for better heat conduction and long life of LED.

The Fixture should comply all International Standarad third party

(LM 79 for complete fixture, LM80 for individual LED). Fixture

wide voltage range from 100 V to 270 V, 50/60 Hz. The Fixture

have protection like miswiring, over voltage, over load, wrong

wiring. The min. lumen output of fixture 80 Lumens/watt. The

fixture should be provided with external separate Potted driver BIS

approved only for safety and performance. (L70 @ 20,000 Hrs.)

The Luminiare should be tested as per IP 20 and following test

reports should be submittedat the time of approval, heat resistant

test, thermal test, Ingress protection test, drop test, (Lighting

Technologies, Philips, OSRAM, GRE, Pyrotech, Orient, Havells,

Ensave make & model approved by EIC subject to above

specification) [Note:-The manufacturer / authorised Channel

partner of the manufacturer has to submit 4 yr free replcement

Guarantee for complete Fixture] 10.00 1050.00 Each

181 Supply & fixing decorative Hanging light with glass having

cylindrical or square shape having length not less than 10" &

width not less 3.5" with holder, lead wire as per required length

but not more than 1mm & base plate for fixing the fitting with

ceiling.[a] suitable for led lamp Cat-III (Provision in Estimate) 10.00 2100.00 Each

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

182 Providing & erecting Decorative wall mounting 9 W LED light

fitting & fixing Accessories with diffuser & Al Housing Body with

white colour 3C x 1.5 Sq.mm Flexible PVC insulated copper wire

for out side wall mounting (Philips, Crompton, Wipro, Bajaj,

Havells make and model approved by EIC only) 8.00 400.00 Each

183 Supplying and erecting LED indoor fittings with LEDs of wattage

0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing

used as a heat sink shall be made of thick sheet Steel conforming

to IS: 513/CRCA/aluminium pressure die cast powder coated and

high U.V. & corrosion resistance with diffuser housed in

aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.9, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates) (D) LED Strip

Light Minimum 4.8 W-120 LED per meter (2 wire, IP-65) with

non integral suitable Driver complete Cat lll (NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.) (Make and model approved by EIC

184 Providing and erecting PVC body surface or pendent mounting

LED Bulk type 9 watt Lighting Fitting with electronic driver

And lumen output from luminaire 720 lm, input voltage range 90-

300 V AC, 50 Hz cool white (3000 to 6500K), inbuilt driver, -

deg C to +60 deg C working temperature, AL frame with Beam

Angle 120 deg [Make- Bajaj, Havells, Pyrotech, GRE]

185 Supplying & Erecting Fan Hook Of 10 mm M.S Round bar

bounded to the RCC bars up to 50 mm Length each side &

piereced through 18 Gauge G.I Box having 125 mm dia depth of

75 mm complete erected concealed in ceiling with necessary

modular plate / sheet. 115.00 145.00 Each

186 Providing & Erecting Fan clamp of 30 x 5 mm flat of required

length & 10 mm M.S. Bolt & Nuts erected with necessary hook of

10 mm M.S. Round Bar. 10.00 115.00 Each

187 Supplying & erecting 19/20 mm. nominal bore "B" class G.I. pipe

/ M.S. pipe down rod erected duly painted for fan complete with

necessary 24/0.2 flat 3 core flexible Core with earthing. (Execute

if fall ceiling occurs) 150.00 125.00 Rmt

188 Supplying & erecting approved make low noise Decorative

exhaust fan having size 200 mm with 1350 RPM with round /

square frame ABS/metalic body with Grill / inbuilt lowers. (Bajaj,

Crompton, Usha Make Only) 12.00 1990.00 Each

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

189 Supply, Installation, Testing and Commissioning of suitable

sweep, BEE 5 Star rated, Ceiling fan with Brush Less Direct

Current (BLDC) permanent ferrite magnet Motor, class of

insulation: B, Rust free 3 nos.Aluminium blades, 2 nos. canopies,

shackle kit with earthing provision, copper winding, Power factor

not < 0.9, Service Value (CMM/W) minimum 6.85, Air delivery

minimum 215 CMM, 350 RPM,230v (tolerance as per IS : 374-

2019), THD < 10%, with remote unit for Speed Control and all

remaining accessories including safety pin, nut bolts, washers,

temperature rise = 75 degree C (Max.), suitable for 140 to

Voltage and rectifier circuit with surge, over current and overload

protection , 50 Hz, Single phase AC Supply, earthing etc.

Complete as required.[ Make shall be approved by Engineer in

PANEL /SWITCH GEAR

190 Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with busbar,

neutral link, earth bar and DIN rail, confirming to IS 13032 and

BS 5486-1986 without MCB to house appropriate nos. of MCBs.

(The DBs should be used of same company of MCB to be used)

(n) Three phase 6 way SS Double door for horizontal single

phase outgoing (Make: HAVELLS, L&T HAGER(AU Series),

LEGRAND(Ekinox3), SCHNEIDER, SIEMENS(Betagard-

191 Providing and erecting Approved make ISI mark ELCB

confirming to IS:12640/1988 having serial number printed on it

and having sensitivity of 30 mA. and breaking capacity of 10 KA

and suitable for 440 V having characteristic of quick acting &

Tripping with all advance feature & do not incorporate any

electronic component (mounted in Box) with same company metel

box with Earthing terminal. with necessary Numbering marking

with oil Paint by painter.Suitable for operation on Three phase

440 Volt max. rating of (iii) For 63 Amp 5.00 4070.00 Each

192 Providing & erecting 415 V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking capacity &

confirms to IS :8828 in existing box having following capacity [c]

63 Amp. Cat.-III (Make: HAVELLS, L&T HAGER(AU

Series), LEGRAND(Ekinox3), SCHNEIDER,

SIEMENS(Betagard-8GB32) (Same as MCDDB Make) 5.00 750.00 Each

193 Approved make ISI mark ELCB confirming to IS:12640/1988

having sensitivity of 30 mA and breaking capacity of 10 KA and

suitable for 240/415 having characteristic of quick acting &

Tripping with all advance feature & do not incorporate any

electronic component (mounted in 1 phase MCBDB) Suitable for

operation on single phase 240 Volt max rating of (i) For 40 Amp.

Cat.-III (Make: HAVELLS, L&T HAGER(AU Series),

LEGRAND(Ekinox3), SCHNEIDER, SIEMENS(Betagard-

8GB32) (Same as MCDDB Make) 12.00 2880.00 Each

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

194 Providing & erecting 240 V MCB Double pole switch for

Lighting load (B curve) having 10 KA breaking capacity &

confirms to IS:8828 in Existing M.S. box having following

capacity. For 40 Amp. Cat:-III (Make: HAVELLS, L&T

HAGER(AU Series), LEGRAND(Ekinox3), SCHNEIDER,

SIEMENS(Betagard-8GB32) (Same as MCDDB Make) 16.00 385.00 Each

195 Miniature circuit breaker single pole 6 Amp. to 32 Amp.

suitable to operate on 240 V A.C. system and having breaking

capacity 10 KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark. Cat.III. (Amp rating of MCB will be

installed as per requirement between 6 to 32 AMP.) (Make:

HAVELLS, L&T HAGER(AU Series), LEGRAND(Ekinox3),

SCHNEIDER, SIEMENS(Betagard-8GB32) (Same as MCDDB

Make) 7.00 130.00 Each

196 Mains with ISI marked, 1.5 KV grade electrolyte multi

stranded, annealed copper conductor with heat resistant PVC

insulated conforms to IS:694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with required size of

copper lugs, nuts and bolts if required. [f] One wire 6.00 sq. mm 50.00 55.00 Mtr.

197 Supplying & erecting approved make Four Pole 415 V change

over switch interior for panel mounting with operating mechanism

A.C.23 duty confirming to I.S.S. for (F) 400 A. Cat.-lll 1.00 26000.00 Each

198 Providing and erecting Approved make Double Door metal clad

D.B. company having Incoming MCB 40 Amp. double pole switch

(C curve) and S.P. MCB of rating 6 to 32 Amp. with NL suitable

to operate on 230 Volt A.C. power and having overload and short

circuit tripping element breaking capacity 10KA to be erected in

flush type and company fabricated 16 G.M.S. sheet box with

powder coated inside and outside after apply seven tank chemical

process of M.S. sheet cover complete with suitable integral single

piece construction tinned copper busbar- and link with all

necessary interconnection. Manufacturer must be Provided (1) IP

43 Protection Certificate (2) IK 08 Certificate (3) Seventank

Powder Certificate (4) Copper/Brass make neutral & Earthing link

with isolation. For 12 Way MCBDB : 6 Amp:- 3 Nos., 16 Amp:-

3 Nos. & 25 Amp:- 4 Nos. [To avoid separate ELCB box two

extra way will be provided in above MCBDB] Cat.-III (Make:

HAVELLS, L&T HAGER(AU Series), LEGRAND(Ekinox3),

SCHNEIDER, SIEMENS(Betagard-8GB32) (ELCB/ MCB

Same as MCDDB Make) 10.00 3427.00 Each

199 Providing and erecting Approved make ISI mark ELCB

confirming to IS:12640/1988 having serial number printed on it

and having sensitivity of 30 mA. and breaking capacity of 10 KA

and suitable for 440 V having characteristic of quick acting &

Tripping with all advance feature & do not incorporate any

electronic component (mounted in Box) with same company metel

box with Earthing terminal. with necessary Numbering marking

with oil Paint by painter.Suitable for operation on Three phase

440 Volt max. rating of (iii) For 63 Amp 1.00 4070.00 Each

STREET LIGHT/CABLES

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

200 Supplying and erecting approved make Octagonal pole made from

HR sheet steel. The pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS:2629/2633/4759, suitable

suspend local wind speed with integral Junction box with Ln

key locking and silicon rubber gasket consist of terminal plate

of min. 6 mm Hylam sheet, standard profile 35 mm X 7.5 mm

Din-Rail & MCB, Brass stud type terminal and arrangement

for cable termination to be erected on RCC foundation as per

details given by manufacturer and EIC considering site

Foundation Details: (1) Grade of RCC 1:2:4, (2) Grade of steel

rainforcement of RCC FE 415, (3) Clear cover to rainforcement

mm, (4) Concrete vibrated, (5) use suttering / farma, (6) Hot deep

galvanized average 70 Micron, (7) Detail drawing will be given by

(C) 5 Mtr. Long 70 mm Top X 130 mm bottom dia, 3 mm

thickness with 200 mm X 200 mm X 12 mm base plate, 4-M16

Bolts and 600 mm long hot deep galvanized J-Bolt, nuts, washers

with 800 mm under ground and 200 mm above ground level and

450 mm dia. Foundation in 1:2:4 proportion. 2.00 8160.00 Each

201 Supplying and erecting Coil type earthing, coil made from

SWG galvanised iron wire with 50 mm OD and 50 turns (length of

turns approx. 200 mm) and having additional continuous streight

length of 3.00 mtr at open end and should be connected to earthing

bolt and burried in 1.5 mtr deep specially prepared earth pit

complete with salt and charcoal/coke as required for coil type

earthing. (Approx weight of coil 1.0 to 1.1 Kgs) 2.00 435.00 Each

202 Supplying and erecting Fabricating terminal box for street light

pole made from 16 SWG M.S. sheet having following size

complete with fixing arrangement for terminal board, with

necessary hole for wire entry and exit from the box. The box shall

be provided with cover and hinges on one side and bolting at other

end The box shall be fixed by clamps fabricated from 25mm x

6mm flat.The box shall be painted with one coat of red oxide and

two coats of paint having following box size. 330 mm x 260 mm x

140 mm (depth). Providing and fixing Terminal board of size 5.0 x

127 x 152.4 mm. bakelite sheet with 15 Amp. kitkat pattern

porcelain fuse unit with suitable brass studs with nuts, washers and

clamps of size 25mm x 3mm suitable for pole painted with one

coat of red lead paint. 20.00 825.00 Each

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

203 Providing and Fixing of bracket consisting of ISI mark "B" class

G.I. Pipe 4.2 cm outside diameter complete with suitable G.I.

Sleeve tubing of 2 mm. thick and required size and length suitable

for 76.5 / 80 mm. required size of pole top having nuts and bolts

for fixing the brackets and having spread of Upto 0.70 mtr. length

with suitable rise as per site condition and suitable welded stiffner

reducer and nipple with check nut complete painted with one coat

of red oxide and two coats of alluminium paint. or Single arm

bracket suitable for terrace as per design given by EIC (a) For

single arm bracket. (Jindal / Asian / Tata / Surya Prakash make

Only) (Fabricators:- Ambica / Fab / Bajaj / Impression equipment

Only) (Test certificate to be submitted) 20.00 573.00 Each

204 Providing and Fixing SITC of Outdoor aesthetically designed

LED Street Light Luminaire with total consumption of Max.

45 W with single piece die cast aluminium housing, high power

LED shall be mounted on high quality metal core PCB with

extremely precison designed heat sink complete with IP66

protection Class with polycarbonate / thoughened glass cover the

fixture should be suitable for pole/bracket mounting. The fixture to

comply both LM79 and LM 80 guidelines with LED module min.

130 lumen/watt with toughen Glass L70 at 50,000 hrs, provided

with high quality polycarbonate lenses for better light distribution.

The Fixture Should be able to be Pole Mounted and also bracket

mounted, provided with high quality driver for protection against

high and low Voltage cut Off, opertional for high amibient and

high humid envirnoments, THD of driver should be less than 10%

and P.F > 0.95. Also the Fixture should meet the following

technical criterias Oprating range Voltage 120 to 300 V, system

efficiency >= 110 lm/w, and total lumens not less then 4500, CCT

> 5000K, CRI > 65, beam angle 120 deg, surge immunity level at

The Separate Potted driver should have over current, over voltage

protection, short circuit protection so that the fixture recovers once

the fault is removed. In addition to the above product should be

operational in the temperature range of 0 deg to 50 deg and

humidity range of 10% to 90% RH. (GRE, Lighting Technology,

Pyrotech make and model approved by EIC only) (Note:- The

manufacturer / authorized Channel partner of the manufacturer has

to submit 4 yrs free replcement Guarantee for complete Fixture)

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

205 SITC of Outdoor aesthetically designed LED Flood Light

Luminaire with total consumption of maximum 120 W with

single piece die cast aluminium housing, high power LED shall be

mounted on high quality metal core based PCB with extremely

precison designed heat sink, complete with IP66 protection Class,

with polycarbonate / Toughened glass cover. The fixture should be

suitable for pole/bracket mounting. The fixture to comply both

LM79 and LM 80 guidelines with LED minimum 130 lumen/watt

with L70 at 50,000 hrs, provided with high quality polycarbonate

lenses for better light distribution. The Fixture Should be able to

be Pole Mounted and also bracket mounted, provided with high

quality potted driver for protection against, high and low Voltage

cut Off, opertional for high amibient and high humid

envirnoments, THD of driver should be less than 10% and P.F >

0.95. Also the Fixture should meet the following technical

criterias. Operating range Voltage 120 to 300 V, system efficiency

>= 110 lm/w, CCT > 5000K, CRI >65, beam angle 120 deg, surge

immunity level at least 10 KV. Flood Light lumens shall be not

less than 12000 (GRE, Lighting Technology, Pyrotech, Philips

make and model only strictly subject to tender specification)

(Note:- The manufacturer / authorized Channel partner of the

manufacturer has to submit 4 yrs free replcement Guarantee for

complete Fixture)

206 Supplying, Installing, Testing & Commissioning of 40 W LED

Outdoor type Post top Lantern light with IP65 protection with

housing made of sturdy aluminium die cast housing with radiating

cool surface and milky white high quality PMMA round cover

with corrosion resistant Grey colour powder coating with high

efficiency potted driver with necessary safety precautions, 10 kv

surge protection device with high min. 3200 lumens LED with

long life of 30K @ L70 (L70@30000 hrs.), Installation bracket as

per site requirement, accessories 3C X 1.5 Sq.mm copper flexible

wire upto terminal box etc. [Make:- Lighting technologies / Philips

/ Wipro / Pyrotech / Crompton / GRE make & model approved by

EIC only] (Note:-The manufacturer / authorised Channel partner

of the manufacturer has to submit 4 years free replcement

Guarantee for complete Fixture) 6.00 6245.00 Each

207 Providing & laying HDPE Double walled corrugated pipes (DWC)

of polyethylene (conforming toIS: 16205 (part 24) 2018) with

minimum load required of 750N capacity with anti rodent and

ultra violet material properties with necessary connecting

accessories of same material at required depth to be laid 90 cms.

under ground for laying of cable below ground / road surface for

enclosing cable and back filling the same to make ground as per

original.For Outer dia. 50 mm and Inner dia. 38 mm (Rex,

Duraguard/duraline, Sy-aron, Gemini, Nobel Polytech Make

Only) (Test Certificate to be Submitted) 200.00 126.00 Mtr.

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

208 Providing and erecting XLPE (IS:7098) (I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid

cms. Under ground or to be laid on wall with suitable G.I. heavy

guage cable clamp or in existing DWC pipe underground or road

crossing or floor of following size of cables. [d] 4 core x 16 Sq.

209 Providing & fixing double compressed heavy duty flange type

brass cable gland with rubber ring for P V C insulated armoured

cable complete with outgoing tails, insulating tape etc. For

following size cables. For 4 core*16 Sq. mm (Sigma, MCI,

Comet, HMI Make Only) 40.00 54.00 Each

210 Providing & Erecting Flexible PVC insulated multistrand

multicore 1.1 kv grade ISI marked copper wires of following size

to be erected as directed. 3 core 2.5 sq.mm. PVC insulated

round copper wire ISI mark. 200.00 85.00 Mtr.

PUMPING MACHINERY

211 Supplying & erecting approved make self-priming domestic

monoblock water pump with 1 H.P motor, suitable for operation

on 230 volts, 50c/s. AC supply with metallic flange, and M.S.

impeller delivery and following discharge. For (a) 40 LPM at

mtrs. head suitable for 25mm dia. Delivery (i) 1.0 HP to

212 Providing and erecting ISI marked PVC insulated PVC Sheathed

Flat flexible Submersible copper cable approved make of 3 Core

x 2.5 Sq. mm. Size. 30.00 90.00 Mtr.

213 Providing and fixing water proof straight joint in PVC insulated

flat flexible copper cable by using insulated material water

proofing material and making the joint complete. UP to 10 Sqmm 2.00 220.00 Each

COMPUTER NETWORK AND P.A. SYSTEM

214 Providing following type of Modular Type Accessories mounted

with 20 G company fabricated metalic box, single mounting base

frame covered with textured / metallic front plate, modules erected

with necessary connection. As desired by Engineer in charge.

Modem Jack for Computer Open RJ-45 Cat.-III 42.00 178.00 Each

215 SITC of specified make X color for Cat.-6 Data to be done in

prelaid PVC pipe / raceway, but without the cost of raceway or

pipe (the wire is to be drawn from MFD/ JB to outlet point) (a)

CAT - 6 (For Computer Cabling and For Voice Cabeling) (Molex

/ D-Link / R & M make Only) 2400.00 51.00 Mtr.

218 ---do--16 port switch 8.00 2300.00 Nos.

FIRE / Intercom

219 “Matrix” make Digital Epabx system Universal slot-8 Ext slot-8

USB prot & auto att. CLI,LCR,CUG,SDMR,15 party conf and

with slot extension facility. 2.00 25000.00 Nos.

220 key phones (Digital) with CLI & Speaker 2.00 2900.00 Nos.

221 Simple phone 15.00 1590.00 Nos.

PARTCULARS OF ITEM

No. QTY RATE PER AMOUNT

222 Termination and Testing of RJ-11 Telephone Socket as per

Industries with ferruling for table, including cost of Site visit for

work and service up to defect laibility period. With Junction Box

223 ISI mark Cable with fitting charges with PVC pipe (PVC fitting

fixed with adhesive solution erected in brick wall / slab along with

continuous G.I. fish wire to draw wires and laid in approved

manner zari) cable and labour charge.Armoured [Jelly Filled] (2)

Twenty Pairs 250.00 222.00 Mtr.

Supplying, Installing, Testing and commissioning of IP CCTV

camera (Dahuva Make) with night vision, full HD, Water proof

(Matel or Plastic body) minmum 20 mtr range

224 16 Channel NVR 2.00 12900.00 Nos.

225 8 TB hard Disk (Survilance) for data storage 2.00 19000.00 Nos.

226 CCTV Cable 500.00 20.00 Mtr.

227 DOM type CCTV Camera 2.00 3500.00 Nos.

228 Bullet type CCTV Camera 15.00 2500.00 Nos.

229 4 U rack for CCTV 2.00 1800.00 Nos.

230 Supply of Fibreglass Step (A Type) Ladder - 10 FT having

following specifications :

It should have nonconductive Structural moulded top, with Slots to

keep tools close at hand, inside Spreader Braces, Aluminium Feet

with thick rubber tread, nonconductive Full channel Fibreglass,

two pairs of gusset support at the bottom step and All gussets are

heavy duty steel.

Capacity : 300 lbs. Step Size : 3” Width : 29” Approx.

Spread : 66”Approx. Wt. : 19 Kg Approx. Cube : 12.54’ 1.00 24860.00 Each

Estimated Cost Section-IV (Incl. CCTV, Lan Cable, Telephone line etc) in Rs.

Total Estimated Cost Section [ I +II+III+IV ] in Rs …

Bidder's offer [B]

GRAND TOTAL [C = A +/- A*B ]

GRAND TOTAL [C = A +/- A*B ]

GST (CGST __% + SGST __%) [ D = C * GST% ]

GRAND TOTAL INCLUDING GST [ E = C + D ]

GRAND TOTAL INCLUDING GST [ E = C + D ]

Final offer in Rs.

Chief Engineer (Material)

PGVCL, Corporate Office, Rajkot