CONSTRUCTION OF PRIMARY HEALTH CENTER AT RAISI, BLOCK LAKSAR. (UNDER P.M.J.V.K.)

Amount

EARTH WORK

DSR NO. 2.8.1 Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

DSR NO. 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

DSR NO. (1-26-2) SOR 2014 Diluting and injecting chemical emulsion (Chlorpyriphos/Lindane E.C. 20% with 1% concentration), at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surfaces of the excavations made for the foundation of the building, soil under floors, apron, back fill material and along all the faces of the walls for PRE-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) as per IS:6313 Part-II. (Plinth area of Building shall be measured for Payment).

DSR NO. 2.27 Supplying and filling in plinth with Jamuna sand under floors including, watering, ramming consolidating and dressing complete.

DSR NO. (3-4) SOR 2018 (laksar) Construction of Embankment with Material Obtained from Borrow Pits Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting tomeet requirement of Tables 300.1 and300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5

DSR NO. 4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).

DSR NO. 4.10 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size).

DSR NO. 4.13 Applying a coat of residual petroleum bitumen of penetration 80/100 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

DSR NO. 4.17 Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm bed by dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth

DSR NO. 5.1.2 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level

1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

DSR NO. 5.2.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

DSR NO. (5.22.6) Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Reinforcement for R.c.c work Using Thermo-mechanically treated bars

DSR NO. (5.9.3) Centring and shuttering including strutting,ropping etc. and removal of form for

DSR NO. (5.9.1) Foundations, footings, bases of columns, etc. for mass concrete.

DSR NO. (5.9.6) Columns, Pillars, Piers, Abutments, Posts and Struts.

DSR NO. (5.9.5) Lintels, beams, plinth beams, girders, bressumers and cantilevers.

DSR NO. (5.9.3) Suspended floors, roofs, landings, balconies and access platform.

DSR NO. 5.9.4 Shelves(Cast in situ)

DSR NO. (6.1.2) Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in

Cement mortar 1:6 (1 cement : 6 coarse sand)

DSR NO. (6.4.2) Brick work with F.P.S. bricks of class designation 75 in superstructure

Cement mortar 1:6 (1 cement : 6 coarse sand)

DSR NO. (6.13.2) Half brick masonry with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level Cement mortar 1:4 (1 cement : 4 coarse sand)

DSR NO. 6.15 Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry (with F.P.S. bricks).

DSR NO. 8.2.2.2 Providing and fixing 18mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut for kitchen platforms, vanity counters ,window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse Granite of any colour and shadeArea of slab over 0.50 sqm.

DSR NO. 9.1.2 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Sal wood

DSR NO. 9.14 Extra for providing ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws. (Shutter area to be measured).

DSR NO. 9.21.1 Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

DSR NO. 9.100.1 Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm

DSR NO. 9.94.1 Providing and fixing chromium plated brass casement stays (straight peg type) with necessary screws etc. complete : 300 mm weighing not less than 330 gms

DSR NO. 9.96 Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete

DSR NO. (9.96.1) 300x16 mm

DSR NO. (9.96.2) 250x16 mm

DSR NO. (9.97.2) Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete

DSR NO. (9.97.2) 250x10 mm

DSR NO. (9.97.4) 150X10 MM

DSR NO. (9.101.1) Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper

DSR NO. (9.51.2) Providing and fixing fly proof galvanised M.S wire gauze to windows and clerestory windows using galvanised M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm. With 12 mm mild steel U beading.

DSR NO. 10.11 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of onlysteel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

DSR NO. (10.30.2) Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :

DSR NO. (10.25.2) Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

DSR NO. 10.3 Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size,with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

DSR NO. (11.41.2) Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 m

DSR NO. (11.46.2) Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 m

DSR NO. 11.37 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

DSR NO. 11.36 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

DSR NO. 11.45 Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge.

ROOFING

DSR NO. 12.21 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75mm deep chase

DSR NO. 12.22 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

DSR NO. (12.41.2) Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :

DSR NO. (12.41.2) 110 mm diameter

DSR NO. -12.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

DSR NO. (12.42.1.2) 110 mm

DSR NO. (12.42.5.2) Bend 87.5 degree

DSR NO. (12.42.5.2) 110 mm bend

Shoe (Plain)

DSR NO. (12.42.6.2) 110 mm Shoe

DSR NO. (12.43.2) Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including

DSR NO. (12.43.2) 110 mm

DSR NO. (13.1.2) 12 mm thick cement plaster in 1:6 ( 1 cement and 6 fine sand) mortar including supply of all material , labour and T&P etc. required for proper completion of the work.

DSR NO. (13.2.2) 15 mm thick cement plaster in cement mortar 1:6 on Rough face of brick wall including supply of all material , labour and T&P etc.

DSR NO. (13.9.2) Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm cement plaster

DSR NO. 13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

DSR NO. (13.41.1) Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade (New work (two or more coats) over and including priming coat with cement primer)

DSR NO. 13.47 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

DSR NO. 13.62.1 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

DSR NO. (22.14.1) Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size

DSR NO. (22.7) Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineerin-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm

DSR NO. 11.3.1 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. omplete. 40 mm thick with 20 mm nominal size stone aggregate

DSR NO. 18.1 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Iinternal work - Exposed on wall

DSR NO. (18.10.1) 15 mm dia nominal bore

DSR NO. (18.10.2) 20 mm dia nominal bore

DSR NO. (18.10.3) 25 mm dia nominal bore

DSR NO. (18.12.5) Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. (external work)(40mm dia nominal bore)

DSR NO. (18.49.1) Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931

15 mm nominal bore.

DSR NO. (18.52.1) Providing and fixing C.P. brass stop cock (concealed) of standard design and of approvedquality .(15 mm nominal bore)

DSR NO. (18.52.1) 15 mm nominal bore.

DSR NO. (18.21.1) Providing and fixing uplasticised PVC connection pipe with brass unions 30 cm length 15 mm nominal bore

DSR NO. 18.19 Providing and fixing gun metal non-return valve of approved quality (screwed end)

DSR NO. (18.19.1.1) 25 mm nominal bore (Horizontal)

DSR NO. 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet, and overflow pipes but without fitting and the base support for tank.

DSR NO. (17.1.1) Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests

DSR NO. (17.2.1) Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever),

DSR NO. (17.7.1) Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass each pillar taps.

DSR NO. 17.4 Providing and fixing white vitreous china flat back or wall corner type lipped front

DSR NO. 17.4.1 One urinal basin with 5 litre white P.V.C. automatic flushing cistern.

DSR NO. 17.11 Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unioncomplete, including painting of fittings and brackets, cutting and making good the wall wherever required :

DSR NO. 17.11.2 Size 600x450x200 mm

DSR NO. 17.35 Providing and fixing soil , waste and vent pipes: S.C.I S&S pipe as per IS:1729

DSR NO. (17.35.1.1) 100 mm dia.

DSR NO. (17.35.2.1) 75 mm dia

DSR NO. 17.37 Providind and fixing M.S.holder bat clamps of approved design to sand cast iron/cast iron (squn) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1cement :2coarse sand :4graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the walls etc:

DSR NO. (17.37.1) 100 mm dia.

DSR NO. (17.37.2) 75 mm

DSR NO. 17.38 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

DSR NO. (17.38.1.1) 100 mm dia.

DSR NO. (17.38.2.1) 75 mm dia

DSR NO. 17.39 Providing and fixing 100 mm sand cast iron S&S plain bend of required degree.

DSR NO. (17.39.1.1) 100 mm dia.

DSR NO. (17.39.2.1) 75 mm dia

DSR NO. 17.4 Providing and fixing 100 mm sand cast iron S&S heel rest sanitry bend of required degree.

DSR NO. (17.40.1.1) 100 mm SCI S&S heel rest sanitary bend

DSR NO. (17.40.2.1) 75 mm dia

DSR NO. 17.43 Providing and fixing single equal plain junction of required degree with access door insertion rubber washer 3 mm thick bolts and nuts complete.

DSR NO. (17.43.1.1) 100x100x100 mm

DSR NO. (17.43.2.1) 75x75x75mm

DSR NO. 17.56 Providing and fixing 100 mm sand cast iron s&s terminal guard

DSR NO. (17.56.1) 100mm

DSR NO. 17.57 Providing and fixing 100 mm sand cast iron S&S collar S.C.I S&S pipe as per IS:1729

DSR NO. (17.57.1.1) 100mm

DSR NO. (17.57.2.1) 75mm

DSR NO. 17.59 Providing and fixing 100 mm M.S stays and clamps for sand cast iron /centrifugally cast (squn) iron pipes of diameter:

DSR NO. (17.59.1) 100 mm dia.

DSR NO. 17.6 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors:

DSR NO. (17.60.2.1) 100 mm inlet and 75 mm outlet SCI tarp

DSR NO. 17.34.1 Providing and fixing toilet paper holder C.P. brass

DSR NO. 19.1 Providing, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture

DSR NO. (19.1.1) 100 mm diameter

DSR NO. (19.2.2) Providing and laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40 mm nominal size) all round S.W pipe including bed concrete as per standard design: 150 mm diameter S.W, pipe

DSR NO. 19.4 Providing and fixing square-mouth S.W. gully trap grade ‘A” complete with C.I.

DSR NO. (19.4.1.1) With F.P.S Brick class designation 75

DSR NO. 19.7 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse

DSR NO. (19.7.1.1) With F.P.S. bricks with class designation 75

DSR NO. (19.8.1.1) Extra depth for manholes

Size 90x80 cm

With F.P.S brick class designation 75

DSR NO. 19.32.1 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

DSR NO. 1.8 WGSTLPT Point wiring in PVC conduit, with piano type switch.

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sqmm. FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with piano type switch, phenolic, laminated sheet, suitable size MS Box and earthing the

DSR NO. 1.8.3 Group C

DSR NO. 1.12 WGSTLPP2 Power plug wiring in PVC conduit (2x4 sq. mm)

Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. (@ 30 mtr./Ckt.)

DSR NO. 1.14 WGSTLSB Circuit/ submain wiring in PVC conduit:

Wiring fir curcuit/ submain wiring alongwith earth wire the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

DSR NO. 1.14.1 2x2.5 sq. mm + 1x1.5 sq.mm earth wire @35m/Ckt.)

DSR NO. 1.14.9 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

DSR NO. 1.14.10 4x10 sq. mm + 2x10 sq.mm earth wire

DSR NO. 1.18 TLWGEC Telephone wiring in PVC conduit:

Supplying and drawing following pair, 0.5 sq mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface/recessed steel/ PVC conduit as required.

DSR NO. (1.18.2) 2 Pair (@30M EACH)

DSR NO. 1.21 PVCCON S/F PVC conduit:

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cuttting the wall and making good the same in case of recessed conduit as required.

DSR NO. 1.21.1) 20mm

DSR NO. 1.22 MB S/F metal boxes:

Suppying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. required.

DSR NO. 1.22.1 75 mm x 75 mm x 60 mm deep

DSR NO. 1.23 PTSWEB S/F piano type switch/ socket:

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required.

DSR NO. 1.23.1 5/6 amps switch

DSR NO. 1.23.4 3 pin 5/6 amp socket outlet

DSR NO. 1.23.6 Telephone socket outlet

DSR NO. 1.25 MODFREB S/F modular type electronic fan regulator:

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

DSR NO. 1.29 LPACCPT S/F light plug point piano type accessories:

Supplying and fixing metal box of 150mm x 75mm x 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 anos socket outlet and 5/6 amps piano type switch, connection, painting etc. as required. (For light plugs to be used in non residential buildings).

DSR NO. 1.30 PPACCPT S/F power plug point plano type accessories:

Supplying and fixing metal box of 180mm x 100mm x 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 amps socket outlet and 15/16 amps piano type switch, connection, painting etc. as required.

DSR NO. 1.33 CREB S/F ceilling rose:

Supplying and fixing 3 pin, 5 amp. ceilling rose on the existing junction box/ wooden block including connection etc. as required

DSR NO. 1.34 BRHOLD S/F brass holder:

Supplying and flxing brass batten/angle holder including connection etc. as required.

DSR NO. 1.41 ITCFFSUR ITC fluorescent fitting directly on surface:

Installation, testing and commissioning of pre-wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling / wall, including connection with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

DSR NO. 1.45 ITCCFFC ITC ceiling fan with cover on fan box:

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq, mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

DSR NO. 1.50 ITCEF450 ITC exhaust fan upto 450 mm sweep:

Installation of exhaust fan upto 450 mm sweep in the existingopening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required.

DSR NO. 1.51 LOUSHEF Fixing louvers/shutters for exhaust fan:

Extra for fixing louvers/shutters complete with frame for a exhaust fan of all sizes.

BOARD & DB'S

DSR NO. 2.4 PWTPMCBDB S/F prewired TP MCB DB:

Supplying and flxing way, three pole and neutral, prewired, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with loose wire box, terminal blocks, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB/ RCCB/ lsolator)

DSR NO. 2.4 6 way (4 + 18), Double door

DSR NO. 2.10.1 MCBC S/F 'C' series, SP MCB

Supplying and fixing 5 amps to 32 amps rating, 240 volts, 'C' series, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

DSR NO. 2.10.1 Single pole

DSR NO. 2.13 MCBTPIS S/F TP MCB isolator:

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissoning etc. as required.

DSR NO. 2.13.2 63 amps

EARTHING

DSR NO. 5.4 EARGIPL G.I earth plate elctrode:

Earthing with G.I earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt ) as required.

DSR NO. 5.9 EARG125X6 S/L 25 mm x 5 mm G.I. earth strip in ground:

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

DSR NO. 10.18)Civil Work) Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Non Schedule Items CEILLING FAN

Supply of AC 230/250 volts, 50 HZ energy efficient ceiling fan with standard down rod, blades, 3 nos. caps Model-ES-50 50/Velocity/Velocity HS (1200 mm Sweep) etc. complete in all aspects as per direction of Engineer in Charge. (Make- HAVELLS )

(Make : Bajaj /Compton / Havells)

1200 mm sweep

Non Schedule Items Supply of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. complete.Model- Turbo Force SP (Make : Havells) 300 mm sweep 900 rpm ,complete in all aspects as per direction of Engineer in Charge.

(Make : Bajaj /Compton / Havells)

300 mm sweep 900 rpm

Non Schedule Items SUPPLY OF LED Bulb B22 Ball Lamp, 15 W ,6000k /4000k/3000K ,230/250 VOLT,50 HZ ETC, complete in all aspects as per direction of Engineer in Charge. (Rate taken from Havells price list w.e.f. 2018).

Non Schedule Items Supply and fixing of LED Tube light 20W (Code- LHEXBYPNIN1W020) ,Lumen Output- 3000, 4000, 6500K, Wall mounted LED batten (E-LITE LED TRIYCA) all in one fixture. complet in all aspects as per direction of Engineer in charge. (Rate taken from Havells price list w.e.f. 2018).

Non Schedule Items Supply & fixing of LED Foot Light (GLiT GB01 Motion Sensor LED Foot Lamp) - Providing & Installation of Factory packed ready to installed LED foot light with Motion Sensor LED Foot Lamp ( Wall Mounted). complete in all aspects including base plate (for recess in wall ) connecting wire etc.of standard make (Glit / Philips/ Havells) as per direction of Engineer in Charge.

Non Schedule Items Supply and fixing of BULK HEAD light- 1 X 8 W CFL bulk head in die cast aluminium housing & frosted glasses complet in all aspects as per direction of Engineer in charge.

Non Schedule Items Supply & fixing of main panel with 1 no. incomer of 100 amp.TPN MCCB (25 KA)& outgoings of 02 no. 40 amp. FP MCB (25 KA) & 03 no. outgong of 15 amp. FP MCB with suitable busbar, change over switch,ammeter, voltmeter,indicating lamps etc. complete in all

SUPPLY AND LAYING OF /CABLES / CABLE TRAYS / CABLE TERMINATION

DSR NO. 4.1 Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

DSR NO. 4.1.15 750 mm width X 75 mm depth X 2.0 mm thickness

Non Schedule Items Supply installation and commissioning of Kirloskar Green Silent DG set (40 KVA)Alternator Three Phase 40KVA/32 KW with 56 BHP engine efficient of standard made (Kirloskar or equivalent) with Acoustic powder coated enclosure fabricated from 16 SWG CRCA MS sheet in nut bolt type assembly construction with dimension accuracy of 0.1 mm and rock wool insulation of doors with loading arrangements with manual automatic control panel battery MCB isolators, busbar earthing for neutral etc complete in all aspects as per direction of Engineer In-charge

Non Schedule Items Providing & fixing CO2 Type Fire Extinguisher complete with Refill, ISI marked Tested & Approved.

capacity 4.5 kg

goyal and sons