WBPWD/EE/N24/EL/e-NIQ148/24-25

Amount

SITC of LT,Cubicle Type,Floor Mounted , totally enclosed, fully compertmentalized electrical control panel suitable for operation at 415 Volt, 50 Hz,as per size, design & drawing to be approved by EIC.The panel board will be fabricated by CPRI approved panel maker as per detail specification below.

The general construction of the pannel will conform to IS 8623:93 as ammended uptodate. The Degree of IP protection for the enclosure will be IP-42.It will have multi tier arrangement, having necessary cable alley at both end, with rigid and self supporting structure fabricated with sufficient no. of channels & covered by 2mm thick CRCA sheet with base structure by 75x40x4mm channel.

All incoming, outgoing MCCB/ SFUs are to be housed in respective compartments with hinged and gasketted doors at the front. All the doors should have pannel lock arrangements in such a fashion that it cannot be unlocked unless the respective feeder remains OFF. The rear of the pannel should have gasketted wire net guard for ventillation and arrangement shall be made for easy access to each compatment by providing rear doors with locking system.

The pannel is to be properly gasketted to prevent the dust and vermin. All vertical and horizontal bus bar chamnbers are to be properly arranged and all electrical switches, busbars are to be fixed by MS nut-bolts on suitable hylam board / non - hygroscopic insulators of adequate size and dimensions. The outgoing feeder connections from respective switches are to be made at the rear side of the pannel by means of bus-bar/multicore copper cables, to be terminated on bolted type terminals for cable connections or bush insulators for bus connection

It will be powder coated after seven tank pretreatment process.2 Nos copper strip of size as per IS shall be fixed all around the panel and will be connected to 2 nos copper earth bus bar connected to incoming earth conductor.All tests should be made for the complete panel.The following 415 / 230 Volt Open Execution Type switches with fuses & accessories will be fixed in the panel. [ ACBs will be Legrand / Siemens / Schneider Electric / L&T /ABB , MCCBs will be of Legrand/ SIEMENS/Schneider/ABB Make. SFU will be Siemens / Schneider/L&T make. All the other accessories will be Legrand /Siemens/L&T Make and as per manufacurers standard ].

BUSBAR 500 V electrolyte grade Copper bus bar with vertical section of size 25 x 5 mm for per Phase RYB, & 20 x 5 mm for neutral bars. . The bus basr shall be fixed with FRP chair & the entire bars are to be insulated with PVC heat Sinkable sleeve of suitable size & color as per direction of E.I.C..Dropping bus is also to be made of Cu ,having the same specifications as mentioned .

INCOMER (i)415V,100A, TPN SFU open execution type in existing cubical Panel with HRC Fuse unit (Cat No-SK95521, FR-5, L&T) (Make- L&T/Equivalent Schneider/ Equivalent Seimens)-1 No.

(ii)415V, 100A, TPN on load front operated Changeover switch open execution type in SS enclosure/cubical with nuts bolts etc (Make- L&T/Equivalent Schneider/ Equivalent Seimens) with terminal shrouds ,source seperators and Phase barriers conforming to IS/IEC 60947-3 with suitable nos of indication lamps showing which source/terminal is on/connected . -1 sets

OUTGOING i) 415V, 63A, TPN SFU open execution type in existing cubical Panel with HRC Fuse unit (Make- L&T/Equivalent Schneider/ Equivalent Seimens- 4 nos ( 2 nos For 6 Way PDB and 2 nos Spare)

CONTROL & ACCESSORIES (i) S& Fixing 415V 3 Ph 4W 5A Multifunctional meter having 4 line display and ability to measure V,A,PF ,kW,kVA etc having accuracy class 1.0 ,flush mounting arrangement 96 x96 cm with S&F of 3 nos of current transformer of size 415/5A. - 1 set

(ii) Phase Indication lamps LED type in RYB colours for all incomming & outgoing

S&F 415 V, 16-32A per way, 4 way HTPN MCBDB with SS enclosure, double door with IP 42/43 protection with 4 pole 63 Amp MCB isolator as incomer and C curve 10KA SPMCBs 12 nos 16-32amp as outgoing, concealed in wall after wall cutting and mending good the damages to original finish incl. interconnection with suitable size of Cu wire, neutral link and earthing attachment. (Legrand).

S&F 250 V, 6-16A per way, (2+8) Way SPN MCBDB with SS enclosure with 40 A DP Isolators as incomer and 12 nos SPMCBs ('C' Curve, 6-16A, 10kA) as outgoing, concealed in wall as to GS (Legrand).

S & F of LT single Phase time control box of 2+12 way SPNDB as enclosure having hinged door locking arrangement consisting of the following accessories with suitable size copper wire incl. finishing the ends by crimping method and painting with powder coated paint over one coat of RO primer i) 25Amps DP MCB (Legrand) 1 No. ii) 2 pole power contractor (L&T Make) - MNX -22 - 1 no. iii) Digital time switch (L & T Make) - 1 No. iv) toggle switch - 1 no. v) LED indicating Lamp - 1 No. vi) 2 way Terminal studbold 25A - 2 no. ( For Compound Light) (NS) (1 no. for 10 nos back side outdoor light and 1 no. for 8 nos. flood light)

Supply & fixing of 1200mm, 240V AC ceiling fan complete with Down rod, blades, canopy, safety wire, P2 type capacitor etc. Incl. Other accessories. (Crompton High Speed/Orient New Breeze)

Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc. incl. S&F connecting wire for down rod upto 30 cm incl. painting the rod with approved paint and making necessary connection as required by 2x1.5 sqmm flexible copper wire.

Supply & Fixing 240V, Modular Socket (2 Module) type fan regulator (Step type) (Legrand Myrius/Honeywell MK) on existing Modular GI switch board with top cover plate incl. making necy. connections etc.

Supplying & Fixing MS fan clam of two piece type for RC ceiling as per approved specification, fabricated from 40 mm x 9 mm MS flat including making good damages to building roof with satisfactory finishing as per GS.

S& D 9“ (230mm) 1370rpm, 40Watt, Metal Body Exhaust fan with all necessary accessories as directed by EIC (EPC Electrical Pvt. Ltd. ).

S& D 12“ (300mm) 1420rpm, 80Watt, Metal Body Exhaust fan with all necessary accessories as directed by EIC (EPC Electrical Pvt. Ltd.)

Fixing only exhaust fan after making hole in wall and making good damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection for exhaust of following diameter: 23 cm (9")

Fixing only louver shutter/cowl on wall with necy. bolts & nuts (6 mm dia x 62 mm long) For 23 cm (9") Exhaust fan

For 30 cm (12") Exhaust fan

Supplying & Fixing 240 V AC/DC superior type Ding-Dong Call Bell (Anchor) on HW board incl. S&F HW board [D13 -20a]

Supply & Delivery of single LED tube light fittings, (18Watt, 230VAC, 50Hz, 4000K NW, THD <10%, Efficiency >105 & <120 Lumen/Watt, Bult in 2.5KV SPD) with all accessories and 1 no. LED Tube as directed by EIC. The LED Luminaries & accessories shall have BEE certification. [Make- Philips/Crompton/Wipro]

Supply & Delivery of Twin LED Fitting (18 watt, 230 V AC, 50 Hz, 5700K CDL, THD< 10%, built in 2.5 KV SPD) with all accessories and 2 nos. LED Tube, as directed by EIC, Luminious efficacy > 105 & <120 Lumen/watt. The LED luminaves & accessories shall have BEE certification. (Make-Pholips/Crompton/Wipro)

Fixing only single/twin fluorescent light fitting suspended 25 cm bellow the ceiling with 2 No. 20 mm dia EI conduit (14 SWG) supports fixed with “L” type MS clamp incl. S&F EI conduit, “L” type (125mmx125mm) 6mm thick and 25mm with MS clamps and connecting the length of PVC insulated wire as per GS.

Fixing only single/twin florescent light fitting complete with all accessories directly on wall/ceiling with HW block and suitable size MS fastener, Ceiling plate, nipples etc. as required.

S & F 9 watt B C type LED lamp (Make-Philips /Wipro /Crompton).

Supply & Delivery of Street light luminaire 30Watt (IP 66) with peanut lens and high poer LED to ensure uniform distribution and higher spacing between poles, 10 KV SPD, THD<10%, PF> 0.95, BIS approved silicon filled potted driver, minimum LPW : 110 lumen/watt and minimum system output 3500 lumen suitable for use with 230 Volt, 50 Hz. (Phillips- BRP030 LED35 CW / WW MR PSU GR DX/Equivalent of Wipro)(for Back side of the Building)

Supply & Delivery of Street light luminaire 100Watt (IP 66) with peanut lens and high poer LED to ensure uniform distribution and higher spacing between poles, 10 KV SPD, THD<10%, PF> 0.95, BIS approved silicon filled potted driver, minimum LPW : 110 lumen/watt and minimum system output 11000 lumen suitable for use with 230 Volt, 50 Hz. (Phillips-BRP409 LED110 CW/M2 FG PSU GR V3/Equivalent of Wipro) (For Main Gate Area)

Supply & Delivery of Flood light luminaire 100Watt (IP 66) with peanut lens and high poer LED to ensure uniform distribution and higher spacing between poles, 10 KV SPD, THD<10%, PF> 0.95, BIS approved silicon filled potted driver, minimum LPW : 110 lumen/watt and minimum system output 11000 lumen suitable for use with 230 Volt, 50 Hz. (Phillips-BVP192 LED110 CW HO NB FG GR PSU/ Equivalent of Wipro). (For Play Ground Light).

Fixing only outdoor / street light type LED light fittings complete with all accessories to be fixed /projected from the wall of the building incl. making holes/providing clamping arrangement & necy. GI reducer as required. S&F 40 mm GI pipe (ISI-Medium) quality 1.5 mts. average length having suitable bend S&F necy. length of 1.5 sqmm PVC insulated single core stranded annealed copper wire and making connections as per GS.

Fixing only Floodlight fittings on top of masonary structure by 3 Nos. 10 mm dia x 87 mm long rag bolts, nuts & double washers complete either 37 mm x 10 mm MS flat support/or by other means as required.

Supplying & Fixing GI waterproof type looping cable box size 200x150x100 mm deep having 4 mm thick comprising of one 250 V 15 A kit-kat fuse unit, one NL on porcelain insulator, one compression type brass cable gland for upto 2- core 16 sqmm PVC/A cable and having lined with rubber gasketted GI top cover with brass machine screws etc., earthing terminal with lug, on steel tubular pole near base, including S&F 40x6 mm thick, MS clamps with bolts, nuts etc. including painting with anticorrosive paint.

Dismentling of the existing old wiring with fittings - fixtures etc and unused materials are handover to the authority.

Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Finolex/Polycab/RR) partly in 20mm size PVC rigid conduit 'FR' (Precision make) [for ceiling portion only] and in 19mm bore, 3mm thick polythene pipe [for horizontal & vertical run embedded in wall], with 1x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Modular type switch (Legrand Myrius/Honeywell MK) fixed on Modular GI switch board complete with 2 no. suitable size “Ph & N” copper bar with top cover plate making earthing attachment fixed on wall incl. mending good damages to original finish. [only PVC Rigid Conduit on ceiling and remaining portion concealed Average run 8 mtr

Distribution wiring in 1.1 KV grade 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Finolex/Polycab/RR) in 20mm size PVC rigid conduit 'FR' (Precision make), with 1.1 KV grade 1 x 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire as ECC, to 6A 3 pin Modular type plug socket & switch (Legrand Myrius/Honeywell MK) on 4 Module GI switch board with 3/4 Module top cover plate on wall incl. necy. connection making earthing attachment, painting and mending good damages to building works. i) On Board

Cutting channel of 40 mm x 40 mm size on masonry wall incl. S&F heavy gauge polythene pipe dia as stated below, by means of iron hooks and supplying and drawing 18 SWG GI Wire as fish wire incl. mending good damages to building works i) 19 mm dia 3 mm thick polythene pipe without earth continuity wire

Cutting channel of 43 mm x 43 mm size on masonry wall incl. S&F heavy gauge polythene pipe dia as stated below, by means of iron hooks and supplying and drawing 18 SWG GI Wire as fish wire incl. mending good damages to building works i) 25 mm dia 3 mm thick polythene pipe without earth continuity wire

Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Ploycab /RR /Finolex) of the following sizes in the prelaid polythene pipe and by the prelaid GI fish wire and making necy. connection as required. 4x80/0.4 (10 sqmm) + 2x84/0.3 (6 sqmm) as ECC (For PDB)

2x84/0.3 (6 sqmm) + 1x56/0.3 (4 sqmm) as ECC (For SPNDB)

2x36/0.3 (2.5 sqmm) + 1x22/0.3 (1.5 sqmm) as ECC (CB, PP)

3 x 22/0.3 (1.5 sqmm) (For Separate Plug )

Finishing of the PVC insulated wire ends by socketting with pin/ ring type copper sockets and insulated tapes etc., including supplying sockets, tapes. 4 x 10 sqmm + 2 x 6 sqmm

2 x 6 sqmm + 1 x 4 sqmm

2 x 2.5 sqmm

Supply and delivery of PVC/XLPE Insulated & Sheathed Armoured Aluminium Conductor Cables for Working Voltage up to 1100 Volts of following sizes. [ Make - Polycab/Gloster/RR Kable ] 4 Core 50 Sqmm (Power Meter to LT Panel Incommer )

2 Core 10 sqmm (For 10 nos back side Outdoor Light, 8 nos Flood Light and 1 no street pole)

Laying of cable following cables on wall/surface including S & F MS clams with earthing attachment in 2 x 10 SWG GI (Hot Dip) Wire, making hole etc. as necy., mending good damages and painting. 4 Core 50 sqmm

2 Core 10 Sqmm

Laying of one No. cable of 2 core 10 sqmm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed (For Street Pole)

S&F of compression type gland complete with brass gland, rubber rings for dust & moisture proof entry of PVC armoured cables as below as per G.S. 4 Core 50 Sq.mm

2 Core 10 Sq.mm

Finishing the ends of following cables by crimping method including S/F dowells solderless sockets, tapes and jointing materials etc. as per G.S. 4 core 50 sqmm

2 Core 10 Sq.mm

Supply & Fixing 240 V, 4 nos. 6 A, 3 pin Modular type plug socket with 4 nos. 6A Modular type switch (Legrand Myrius/Honeywell MK), 16A Modular switch type MCB (C-Curve) and Indicator without plug top on 2 row 18 Module GI Modular type switch board with 2 row 18 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. .(For Computer Board)

Supply & Fixing 240 V, 2 nos. 6 A, 5 pin Modular type plug socket (Legrand Myrius/Honeywell MK) with 2 nos. 6A Modular type switch, without plug top on 6 Module GI Modular type switch board with 6 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. (For Set top Box & TV)

Supply & Fixing 240 V, 16 A, 3 pin Modular type plug socket (Legrand Myrius/Honeywell MK) with 16A Modular type switch, without plug top on 4 Module GI Modular type switch board with top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc.

Supply & Fixing 240 V, 6 A, 3 pin Modular type plug socket (Legrand Myrius/Honeywell MK) with 6A Modular type switch, without plug top on 4 Module GI Modular type switch board with 3 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. (For Separate Plug)

Supplying & Fixing CRC sheet metal (16 SWG) JB-cum Switch Board of the following sizes complete with three no. suitable size Copper bar with holes (for Ph, N & E) fixed on bakelite/Hard Rubber insulator over the MS welded chairs incl. bakelite/Perspex/coloured Perspex (wall matching colour) top cover 3 mm thick flushed in wall for housing the board after cutting the brick wall incl. making earthing attachment, painting and mending good damages to building works 175 mm x 100 mm x 65 mm (To be used as JB only)

Dismantling steel tubular/Rail/Strut embedded in CC foundation incl. excavation, filling of holes, restoring surface, loading at site and delivering, unloading, sorting, stacking properly at any place as per direction upto a lead of 1.6 km

Supply & Delivery of 9 mtr. Swagged type Single Steel tubular Pole ( Make - Jindal/ Bansal ) from Store to work-site as per specification type 410- SP- 28 as overall length 9.0 mtr. and Planting Depth - 1.50 mtr, Approx weight of Pole -- 113 KG. and having dimension as per details given below : outside Dia & Thickness of Section as Bottom section ( 139.7 x 4.50 ) mm., Middle Section - ( 114.3 x 3.65 ) mm, Top section ( 88.9 x 3.25 ) mm. and Length of Section -- Bottom - 5.00 mtr; Middle - 2.00 mtr; Top - 2.00 mtr. with fixing the MS base plate incl. necy. arrangements. as per direction of E.I.C. [ NS ]

Erection of Single Steel tubular pole of length as given below with/without sole plate & Cap etc. in CC foundation (Proportion and dimension indicated below), having 600x600x150 mm thick CC (4:2:1) base block below sole plate/pole with hard jhama metal including CC (6:3:1) muffing 0.30 mts. dia and 0.30 mts. above ground level including 3 mm thick neat cemented finish and GI earth bolt after making drilled holes etc. on pole & carriage of pole upto 1.6 Km from Store to work-site including filling up the excavated earth pit with shifted soil and ramming properly. Upto 9.0 mtr. Size 0.6x0.6x1.70 mts

Fixing outdoor type LED light fitting on pole including S&F 40 mm dia x 1.68 mts. long GI Pipe (ISI-Medium) bracket with 40 mmx10 mm thick, MS clamp etc. and providing wiring with 2x1/1.40 PVC insulated and sheathed wire (single core) from loop box at the base of pole to light fiting through pole & bracket (without control switch) including making connections & painting.

Painting of Steel Tubular Pole of lengths and no. of coats of paint, as given below with ready mixed paint/primer of approved make, and brand incl. preparation of surface by sand paper/emery paper, cleaning etc. for receiving fresh coat of paint. -- Upto 9.0 mtr. long pole. 1st coat of aluminium paint over 1 coat of RO priming.

2nd coat of aluminium paint over 1st coat.

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level By ISI-Medium GI pipe with excavation of soil.

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required.

Connecting the equipments to earth busbar including S & F GI (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages, No. 8 SWG

Single phase (1 in 1 out) Hybrid/Off-Grid 7.5 KVA inverter. Certification/Compliances: IEC61727, IEC 62109-1/2, Efficiency [%] : 90% and above, Rating: 7.5 KVA and above, No of independent MPPT: 2, Topology / cooling concept:: Transformer less, Degree of protection (according to IEC 60529) : IP65, Display: Graphic, Interface: RS485, Noise emission (typical) : 51 dB(A), Operating Temperature range: −25 °C … +60 °C (UTL/Deye/Powrone/Exide)

12V 200Ah C10 Battery (Make: Exide/UTL/equivalent)

Array Junction Box (AJB) as per pre approved design. IP 65, IEC 62208. 32A fuse, 40KA Type-II DC SPD Terminator AJB. (Trinity/Sunbird)

AC Distribution Box (ACDB) as per pre approved design. IP 65, IEC 62208. 125A Circuit Brecker/MCB, 4 Pole 40KA Type-II AC SPD, Terminator for ACDB. (Trinity/Sunbird)

2M GI Earthing pipe with Pit cover (IS 2044)

2M GI conventional Lighting Arrestor

Supply & Installation of 25mmX3mm GI Earthing Strip.

Chemical Compound for Earthings

Single core copper 4 sq mm DC cable. IEC 60189, IS 694/ IS 1554, IS/IEC 69947 (Polycab/Havells/Microtek)

2 Core 16 sq. mm aluminium armoured AC cable. (Polycab/MESCAB/Havells)

MC4 Connector

Civil Works with materials for Earthing Pit.

MNRE approved BoS

Engineering, Transportation, Loading/Unloading, Installation & Commissioning

MODERN TECHNO CORPORATION

FUTURE SOLAR SYSTEMS