Repair to plastering of RCC facia, chajja, roof treatment and treatment of toilet/seepages in MD ACCN at YOL CANTT under AGE B/R-I of GE (KH) YOL

Amount

PART-I:- Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each and removing from site, all as specified

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4 Sqm each and removing from site, all as specified.

Taking down shutters of any description exc. 1 Sqm not exc. 2 Sqm each and removing from site, all as specified.

Pressed steel frames of size 105x60mmx1.25mm for door with two rebates including necessary fixing lugs, hinges, lock strike plate, 25x3 flat iron 230mm long hold fast etc, including back filling with PCC M-15 (nominal mix) type B-0 using 12.5mm graded crushed stone aggregate complete, all as specified.

Pressed steel frames of size 125x60mmx1.25mm for door with two rebates including necessary fixing lugs, hinges, lock strike plate, 25x3 flat iron 230mm long hold fast etc, including back filling with PCC M-15 (nominal mix) type B-0 using 12.5mm graded crushed stone aggregate complete, all as specified.

35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, all as specified.

Factory made second class hard wood (Sal) glazed and Skelton door shutters 35mm thick open rebated and prepared to receive glass gauge etc (with sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass or gauge etc., size of members of shutter as specified in clause 8.24 (a) of part-I, fitted to chowkats, complete all as specified.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 180 of MES SSR 2020 Part-II.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.

Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 60mm x 25mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick required no of each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:-(i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window. (ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf. (iii) MS tower bolt 150mm long - 2 No per leaf. (iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf. (v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf. (vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf. (vii) Flat iron fillets of size 20X3 mm for fixing wire gauge. (viii) MS work with angle or other section as in window gurad bars, grill (ix) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 26/13. if iron scrap retrived under this item shall be sold to contractor under Sch of credit. Make : As per Appendix 'C'.Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.

Chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165.

Stainless steel wire cloth. 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples or wooden beads, complete all as specified.

Sheet glass 4mm thick ordinary quality and glazing with oil putty/aluminium beads in squares, not exc. 0.5sqm in each pane, complete all as specified.

S&F for 50 micron powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F for 50 micron powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified complete all as specified.

S&F for 50 micron powder coated anodised anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified.

Butt hinges (ISI marked), medium weight, cold rolled, mild steel 100mm long, all as specified.

Butt hinges (ISI marked), medium weight, cold rolled, mild steel 75mm long, all as specified.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 100mm, fixed, all as specified.

Extruded aluminium alloy handles (ISI marked), fabricated type, anodised, of size 75mm, all as specified.

Aluminium alloy, anodised, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm with lipping frame to match, all as specified.

300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Small fittings of 2nd class hard wood (SAL) such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including 50mm long, medium weight, cold rolled mild steel butt hinge, articles not exc. 200 cu.cm. each including preparation of articles and applying two coats of synthetic enamel paint over a coat of pink primer, all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish of the premisses, complete including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.06 Sqm but not exc. 0.11 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Vitrified ceramic tiles light shade, 10mm thick (Square/ rectangular) area of each tile not exc. 0.36Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Vitrified ceramic tiles light shade, 10mm thick (Square/ rectangular) area of each tile not exc. 0.36Sqm, in vertical surfaces such as skirting and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick rendering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Glazed coloured tiles of size 350x250/450x350x7mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with white or coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Demolition of cement concrete reinforced of any description in any position complete including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.

TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. For fair finished flat surfaces of concrete, all as specified.

Marble 18 to 20mm thick, green marble, (table rubbed and polished) as in kitchen cooking platform /shelf and verticle surfaces duly machine cut in skirting /dado/steps, jambs and pillars and like laid over and including 15mm thick screed bed in cement mortar (1:4) including pointing in grey cement (1:2) using marble dust with admixture of pigment to match with marble shade green marble type, all as specifiedand directed.

Reinforced cement concrete, M-15 (Nominal mix), type B-1, (with 20mm graded crushed stone aggregate as) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, all as specified.

Rolled sections as in Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240s, steel work complete, all as specified.

Demolition of cement concrete (unreinforced) of any description and any position not otherwise specifically provided for sunken portion, complete including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.

Taking down existing unserviceable roof treatment materials and PCC/ cement mortar padding etc complete from roof carefully by cutting chiselling, cleaning the surface by scrapping, brooming, brushing etc and removing the rubbish from site complete, all as directed by Engr-in Charge.

15mm thick (average) screed bed/ plaster in cement mortar 1:4 in order to maintain proper slope and base over existing roof surface, surfaces finished even and smooth without using extra cement for laying water proofing treatment, mixed with water proofing compound as per manufacturer instructions, complete, all as specified and directed. (Note:- WPC and BTD treatment shall be measured and paid separately)

Water profing treatement of sunken portion/water tank padding using high solid content single component water based liquid applied elastomeric water proofing membrene as ASTMC 836 and ASTMD 6083, thickness of the memberane shall be 1.5mm, having solid content of more than 80% elongation of 500+(-) 50% laid over reinforcing layer on non woven geo-textile mesh of 40/50 50gms, including applying self primer coat by diluting with 1:1 ratio @ 0.2 kg per sqm and suface preparation including cleaning of existing treatement, complete all as per manufacturer instructions, complete all as specified and directed by Engineer -in -Charge.

Rendering cement plaster 10mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (5mm thick first layers and 5mm thick 2nd layer) mixed with WPC @ 3% by weight of cement on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, complete, all as specified. Note :- water proofing compound shall be include quoted rates.

Cutting existing steel tubing of 15mm bore for alterations or additions (Each cut measured) if necessarily done in position without taking down complete, all as specified and directed.

Cutting existing steel tubing of 20mm bore for alterations or additions (Each cut measured) if necessarily done in position without taking down complete, all as specified and directed.

Disconnecting existing PVC/ferro cement/MS tanks capacity upto 1000 litres, setting aside (or lowering if required) for cleaning etc, and hoisting if required reconnecting and re-fixing in position including repairing cleaning and removing all scale and dirt etc. from tanks and from mouth of circulating pipes etc., all as specified.

Plain cement concrete M-5, nominal mix, E-2, using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete, as in sub base layer under floors, sunken floor, all as specified.

25mm thick Plain cement concrete M-15 nominal mix, B-1, using 20mm graded mechanically crushed stone aggregate as in sunken floors, complete all as specified.

Demolition of cement concrete (unreinforced) in ground floors and paving, not exceeding 15cm thickness (below or above ground level), un-reinforced including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Dismantling ballies, hard or soft wood, any position, except in posts and struts; including taking out iron straps, bolts and nuts, etc., for Type-2, complete all as specified.

Dismantling boarding, any description, fixed in any position with screws.

2nd class hard wood (Sal/Hollock) plain, solid, straight chowkats and frames, wrought, framed, rebated on solid, rounded or chamfered, put together with glue, pinned at joints with one or more rebates, all as specified.

18/19mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in cup board shutters/shelves etc., complete, all as specified.

Extra over rates of block board or veneered particle board for external teak wood lipping, 6mm thick fixed with nails, complete, all as specified.

Hasp and staple, safety type, aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws of size 75mm, all as specified.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised Width of flaps (when open) in 40mm, all as specified.

40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished, complete all as specified.

Demolition of stones or brick masonry or block walling, built in cement mortar including all quoins, arches etc., but excluding ashlar facing, dressed stone work etc.complete all as specified and as directed.

Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified.

All as per item No. 56 above but except brick. Note:- Old bricks obtained against demolition shall be used.

Sink without drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x160mm, fixed in repair, complete all as specified.

Mild steel galvanized iron water tubing 32mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor/ sunken floor spout complete including taking up or down old pipe, complete, all as specified and directed.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors bore 110mm complete, including taking up or down old pipe, all as specified.

PVC (SWR) pipes single socketed,in any length with rubber ring joints, laid in trenches or in floors bore 75mm complete, complete, including taking up or down old pipe, all as specified.

PVC (SWR) junction single, (Single T) equal or unequal, 75mm bore, provided with oval access door and fixed in repair, all as specified.

PVC (SWR) bends any radius, 110mm bore (fitted with oval access door, and fixed in repair, complete all as specified.

PVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, provided with oval access door and fixed in repair, all as specified.

PVC (SWR) bends any radius, 75mm bore (fitted with oval access door, and fixed in repair, complete all as specified.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding PVC float ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/ PVC storage tank, all as specified.

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with PVC ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-I using 20mm graded crushed stone aggregate complete all as specified, flushing pipe, anti-syphonage pipe, fixed in repair, complete, all as specified.

Supply and fixed in repair PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve, float and handle with brackets including 32mm dia PVC long bend flush pipe 90cm long snd 15mm dia PVC connection 600mm with CP brass coupling 32mm nuts and PVC washers at both ends, fixed in repair, complete, all as specified.

Wash basins, Vitreous China (Flat back type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450mm long PVC connections 15mm size with CP coupling nuts at both ends, screwed for iron pipe and fixed in repair, complete all as specified.

32mm dia Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ cm2 laid in trenches, complete all as specified.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed of 15mm bore and fixed in repair, complete, all as specified.

Bib taps, fancy type, 15mm bore, cast copper alloy with crutch or butterfly handle, fancy type chromium plated screwed for iron pipe or for brass ferrule and fixed in repair, all as specified.

Angle valve, cast copper alloy, fancy chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repair complete, all as specified.

PVC connection 15mm size with PTMT nuts at boths end 450mm long, all as specified.

M&L 32mm dia Waste coupling, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed in repair, complete all as specified and directed.

75mm bore Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) and fixed in repair complete all as specified.

100mm bore Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) and fixed in repair complete all as specified.

Soap dish vitreous China white, approximate size 160x 160x90mm, chromium plated, fixed to plugs with chromium plated, brass screws, all as specified.

Brass Chromium Plated, tubular towel rail, 20mm dia, D type, 45cm long between flanges, with brackets, fixed with chromium plated screws, fixed in repair, complete all as specified.

Dismantling timber scantlings 40 sqcm and over in section, in any position, unframed work, complete all as specified.

2nd class soft wood (Kail) as in scantling clean sawn timber fixed in framed, complete, all as specified.

Dismantling wrought iron or mild steel work of any description. all as specified.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.410W Gde E-250 quality A, steel workcomplete, all as specified.

Dismantling plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof covering, all as specified.

Corrugated galvanized iron mild steel sheets 0.63mm thick, grade ‘O’, with 120 grams per square metre zinc coating fixed with 'J' or 'L' hook as in roof covering with two corrugation side lap. (Horizontal distance of side lap shall not be less than 145mm and depth of corrugation shall be 12.5mm), all as specified.

All as per Serial Item No 86 above but except sheet. (Note:- Serviceable pipe retrieved from Serial Item No 85 shall be used).

0.80 mm thick plain galvainsed mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete, all as specified.

All as per Serial Item No 88 above but except sheet. (Note:- Serviceable pipe retrieved from Serial Item No 85 shall be used).

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

All as per Serial Item No 90 above but except sheet. (Note:- Serviceable pipe retrieved from Serial Item No 85 shall be used).

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

All as per Serial Item No 92 above but except sheet. (Note:- Serviceable pipe retrieved from Serial Item No 85 shall be used).

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, all as specified.

S & F 6mm thick E-board (classic) false ceiling of size 610x610mm fixed with aluminium snap grid frame work of same size as aluminium tee of size 25 mm x25 mm x1.5 mm as main runner, aluminium tee of size 25mmx25mmx1.25mm as cross runner and aluminium angle of size 25mmx25mmx1.25mm at the perimeter suspended from soffit at approx 900mm centre to centre with hangers 6mm dia galvanized (length as per site requirement) adjusting level fixed to roof by means of ceiling cleats made out of galvanized iron flat 40mmx3mm size, 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including necessary scaffolding, complete all as specified and directed.

Complete removal of existing treatment of old plastered surface including by brooming down or with steel wire brushing scraping down smoke soot, moulded moss and efflorescent salts and cleaning oil and greasy spots and cleaning with water on walls and preparation of plastered surface of walls and applying two coats of exterior grade weather resistant paint over a coat of primer over 2mm thick wall care putty, including cleaning the floor/joinery, surface glass pans etc., complete, all as specified.

Taking down cement plaster on brick or stone walls, ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.

Rendering cement plaster 15mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) on fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering plaster 15mm thick in cement mortar 1:6 (1 cement :6 coarse sand) on other than fair faces of brick wall or stone wall surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 3mm thick in cement mortar 1:3 (1 cement : 3 coarse sand) on ceiling, complete all as specified and directed.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper, complete, all as specified.

Preparation of newly plastered wall surfaces and applying two coats of exterior grade weather resistant paint over a coat of primer including cleaning the floor/joinery, surface glass pans etc., complete, all as specified.

Three coats of white wash on newly plastered surfaces of ceiling including preparation of surface complete, all as specified and as directed.

Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.

Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.

Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

All as per Serial Item No 106 above but except pipe. (Note:- Serviceable pipe retrieved from Serial Item No 104 shall be used).

Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

All as per Serial Item No 108 above but except pipe. (Note:- Serviceable pipe retrieved from Serial Item No 105 shall be used).

Supply only intergal water proofing compound, complete all as specified.

15mm bore Ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule fixed repair all as specified.

Taking down shutters of any description exc. 1 Sqm not exc. 2 Sqm each and refixing the same opening, complete all as specified.

Applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces of any description, exc. 10cm width or girth including preparation of surfaces, all as specified.

Applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, all as specified.

M&L for taking down old decayed plaster from RCC fin, facia, cleaning of all surface by brooming, scraping etc and applying one coat of anti corrision paint to visible reinforcement and replastering the same as per existing surface and applying two coats of cement base paint over a coat of chalk whiting primer including preparation and necessary scaffolding etc. complete all as specified and directed. Note:- quoted rate including plastering.

Gun metal, globe or gate valves, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repaair, complete, all as specified.

Gun metal, globe or gate valves, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions and fixed in repaair, complete, all as specified.

Extra over rates of block board or veneered particle board for external teak wood lipping, 6mm thick fixed with nails for 35mm thick flush door shutter, complete, all as specified and directed.

MM Constructions