DEPOSIT Panayam Grama Panchayath Commissioning of newly constructed tube well and its allied works in Panayam North Govt LP school at Ward No. XV of Panayam Panchayath.

Amount

Construction of a Pump house (2mx2m), Bleaching powder stack room(1mx1.2m) and Chlorine tank facility

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

50.6.1.4:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand ) etc complete

50.2.25.1:Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

50.10.1:Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

12.1.2:Providing corrugate G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.80 mm thick with zinc coating less than 275 gm/m2

OD126578/2024-2025:Wiring the pump house and Providing 4 nos light point, and 1 No Fan point and one socket etc wiring the pump house using best quality copper wire with pvc pipe and fitting switches, sockets etc in two switch board and supply and fitting 2 nos. 20 w CFL bulbs, 2 nos. tube set, 1 no. sealing fan best quality as per IE rules.

OD153668/2024-2025:Providing chlorinator arrangements to the tube well pump house by supplying and fixing 2 nos synthetic PVC tanks of 750 liter & 500 liter capacity with the platform outside the pump house and supply and erecting 1 HP special type dosing pump with all accessories suitable to pump bleaching powder solution connecting to the 80mm GI pumping main near the well including cost of all materials labour charges etc complete

Automation arrangements

OD126581/2024-2025:Installation charge for sub pump controller kit.

OD126582/2024-2025:Supply of SIM , SIM kit and including plan for one year

OD126583/2024-2025:Supply of M POWER module for mobile starter for motor.

OD126584/2024-2025:SUPPLY OF MU-G20 fully automatic star delta starter for automation .

Supply and erection of Pump set and its allied works

OD127902/2024-2025:Supplying electrically operated brand new submersible pump set without accessories for erection in tube well size 200mm diameter from reputed KWA approved brand capable to 166 LPM discharge & total head of 80 M with delivery head size of 80 mm suitable to couple electrical motor ac 400/440 v , 50 cycle .The pump shaft should be stainless steel with bronze impeller the cost including all taxes duties and conveyance etc complete as per the direction of the departmental officers. (Two year warranty for pump set)

OD127912/2024-2025:6MM square 3 core copper cable

OD127913/2024-2025:CI Non Return Valve, Conforming to IS 5312 Part I - 1984, PN 1.6, Size 80mm.

OD127920/2024-2025:providing and fixing 100Amps fuse unit and connected woks

OD127925/2024-2025:10MM square PVC copper wire

OD127955/2024-2025:Fabrication of panel board, Supplying and fitting 63 A 3 phase ELCB, 6 KVAR power factor correction capacitor, Indicators, 63 A isolater

OD128248/2024-2025:Supply of 80mm UPVC column pipe including coupling

OD127973/2024-2025:Charges for supplying best quality suitable size 80mm heavy duty CI bottom and top side adapter

OD128333/2024-2025:Charges of supplying 80mm GI pipe

100.98.512:Supply of CI Plain End Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.0, Size 80mm.

OD128273/2024-2025:Erection of 5 HP submersible pump set including erecting the pump set into the tube well after coupling the pump and motor, erecting the column pipes one by one after coupling the same & welding MS flats across the joints, coupling the delivery pipes and valves to the vertical column pipes, connecting motor to starter after connecting all wires and cables etc. complete as per the direction of departmental officers.

OD128315/2024-2025:Charges for fabricating 80mm GI 'T" for interconnecting the pumpingmain connections with valves and specials as per the correct measurement and position after cutting the 3 mtrs. long 80mm GI pipe then shaping and drilling for the GI pipe and fabricating new GI 'T' as per the correct measurement and testing etc. complete including cutting, grinding, drilling and fabrication charges and excluding cosdt of supplying specials

OD128316/2024-2025:Charges for supplying best quality 16mm wire rope erection work

OD128373/2024-2025:Charges for Fabricating 80mm MS flanges at 4 endsides such as cutting shaping the 6 mtr. long 80mm GI pipe as per the correct mesurement and position and fabricating bothside end of the GI pipe with 80mm MS flanges ( for horizontal side in trench) and cutting/ shaping 1 no. new 80mm GI bend and Fabricating both side end of the GI bend with 80mm MS flanges as epr the correct position ( for interconnection to OH tankside pumpingmain connections ) and testing the etc. complete including fabrication charges, cutting, grinding charges and cost of welding rode and cutting/ grinding wheels.

OD129390/2024-2025:Charges for supplying best quality heavyduty 80mm GI bend

OD129410/2024-2025:OVER VOLTAGE RELAY

Pumping main and allied works

15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

100.1.1:Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed, within a lead of 50m, in all kinds of soil.

100.98.224:Supply of PVC Pipe, 8kg/cm2, 110mm Dia.

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

100.9.9:Laying uPVC pipes of class 2 to class 6 and specials, lowering to the trenches already made, placing in position aligning the pipeline to the lines and levels and jointing the pipes and specials with solvent cement and testing the pipeline with water to the required test pressure (excluding cost of pipes and specials): 110 mm nominal outside diameter pipes.

LIJEESH V (BID ID -2159193)

B SIVAPRASAD (BID ID -2159690)

Bidder Name

B SIVAPRASAD

S.Shaji

LIJEESH V