WBMAD/ULB/HM/GEN- 5 (2025-26)

Dismantling terraced roof in ground floor roof (including floor finish, if any.) taking out carefully tiles with beams, joists, tees or burgahs covering floor below, sorting and stacking sevicable materials at site and removing rubbish as directed within a lead of 75 m. (P.No.1, T/3(a) a) In ground floor including roof.

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in 1st floor. P.no. 16, T/16)

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding /staging where necessary .[Excluding cost of chipping over concrete surface] (P-69, T-1) 3rd corrigenda, (a )With 1:6 cement mortar (b) 20 mm thick plaster (Inside plaster) 20 mm thick plaster (b) Extra for each additional floor

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (P-64, T/35) (A) Floor With polymerised Adhesive and Epoxy grout pointing including spacer-2 mm (when tiles are laid over existing hard ready surface) (b) Area of each tile above 0.09 Sq.m (i) Coloured decorative

(B) Wall With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (b) Area of each tile above 0.09 Sq.m (i) Coloured decorative

Supplying,fitting & fixing of 2-Track / 3-Track Aluminium sliding Window of all Aluminium sections viz. window frame (top,bottom & sideframe), shutter (top, bottom, side & interlock member) made of aluminiumalloy extrusions conforming to IS 733-1983 & IS 1285-1975, annodisedconforming to IS 1868-1983, fitted with all other accessories viz. PVCroller, EPDM gasket, maruti lock, screwsetc.including labour chargesfor fitting & fixing of aluminium 2-track/3-track sliding window withfixing of glass (excluding cost of glass) all complete as per architecturaldrawings and direction of Engineer-in-charge.10-12 Micron thickness Annodizing film Natural white. FOR 3 TRACK WINDOW

Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & upto 6 m height for external wall) (P.No.205, T/1) (ii) 4 mm thick

(b) Priming one coat on timber or plastered surface with synthetic oilbound primer of approved quality including smoothening surfaces by sand papering etc (P.200, T/1 (a) (b)) (3rd corrigendum)

(a) On timber or plastered surface : With super gloss (hi-gloss) - (iv) Two coats (with any shade except white)

Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor) (b) Two Coats i) Water based interior grade Acrylic Primer (P.195, T/7 (i))

Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - In Charge. (Payment will be made on finished length of the work). j) Fixed partitions. (Unsupported length of vertical member upto 1.5 mtr. Height of both ends of vertical member restrained but panels within 0.9 sq.m.) (P.No.234, T/1 i) Top , bottom & side member.

ii) Intermediate member.

ii) Shutter : Top rail.

Bottom rail.

Lock rail

Door vertical.

Glazing cleap.

Providing and fixing exterior quality Aluminium Composite Panel (ACP) wall cladding on existing Al. /MS frame work with GI brackets, ACP fixed on the existing frame work by folding the edges of ACP panel (Engraving the rear surface of ACP sheet) with CP angles, cleats and strainless Steel screws forming groves at the periphery of ACP panel. Such grooves filled with foam and silicon sealant etc. complete with all materials (but including the cost of silicon sealant), labour, scaffolding and all other incidental charges complete in all respect as per specification and direction of Engineer-in-charge. (Mode of payment is on finished surface area of ACP) (b) 4mm thick (0.50mm Al.+3.0mm LDPE +0.50mm Al. PVDF coating)

Supplying, Fitting & Fixing 30 mm thick both side prelaminated Factory madesolid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S.frame shall have cost of steel primers of approved make and manufacture, M.S.frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheetout of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mmshall be flat and 20 mm shall be tapered on both sides to form lock rail. Top,bottom and lock rails shall be provided either side of the panel with 10 mm (5mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom railsheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined togetherwith solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesiveetc. complete excluding all necessary hardwares as per direction of Engineer-in-Charge. (P-125, T/15)

Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (P-12, T/19 (I)) Plumbing & Sanitary Schedule 2017 (a) For Exposed Work PVC Pipes (ii) 20 mm dia

Supplying, fitting and fixing bib cock or stop cock. (P-6, T/7) Plumbing & Sanitary Schedule 2017 (a) (i) Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand). 15 mm

(d) (i) Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand).