CA NO GE SOUTH AMB 58 2024 2025 COMPREHENSIVE REPAIRS TO MARRIED ACCN OF NBC AT AGE B R I UNDER GE SOUTH AMBALA CANTT

Amount

Material and labour for cleaning the roof top surfaces, brick tiles or concrete surfaces by picking vegitation roots, sweeping clean and washing down with water to remove dust etc and filling & damaged joints of brick tiles in CM 1:4 complete all as spd and directed.

Material and labour 40mm thick average thickness PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in roof padding, levelling course and finishing top surfaces even and smooth without using extra cement to receive APP membrane , complete all as specified and directed.

Material and labour for APP polymeric water proofing treatement to roof using membrane minimum 3 mm thick and weighting not less than 3.6 kg/sqm , black finish reinforced with non-woven polyster matt (Weight not less than 150 gms/Sqm) with thermo fusible finish laid by force application after applying compatible bitumen primer at the rate of 0.40 Ltr per Sqm, by the same membrane manufacturer of density 0.87 to 0.89 kg/ltr at 25' C temprature and viscosity 70-160 cps over the primer coat, torching over laps with a propane or butane gas torch with a over lap of 100 mm at the side and 150 mm at the ends and sealing including a tack coat of hot blown bitumen 85/25 @ 1.2 Kg/Sqm below APP and two coats water proofing paint with aluminium finish on top of laid APP surfaces including preparation of surface complete all as specified and directed. NOTES : - (i) The water proofing treatment shall be got carried out by the manufacturer or their authorised applicators duly approved by GE in writing. (ii) 5% amount of the total amount of water proofing treatment shall be retained as a guarantee and shall be released after 10 years. However contractor may deposit the FDR of same amount in favour of GE. If contractor fail to rectify the defect pointed out during this period in writing, the defect shall be got rectified at contractor' risk and cost and the payment shall be made from the amount kept reserved or by encashing the FDR deposited by the contractor as guarantee. Contractor's quoted rate for this item shall deemed to be inclusive of this aspect.

Material and labour for PCC in roof kerbs of mud stops, rounded or chamfered on edges type B0 (1:2:4) using 12.50 mm graded aggregate including dismantling of existing PCC complete all as specified and directed.

Material and labour for preparation of old decorative surface of wall etc by washing rubbing down including scrapping and applying one coat of cement base paint of any tint complete all as specified and directed.

Material and labour for preparation of old decorative surface of wall including washing rubbing down and stopping of distempered and painted surfaces and applying one coat of oil emulsion paint complete all as specified and as directed.

Material and labour for complete removal of existing treatment on surface of walls by using appropriate technique as approved by Engineer-in-Charge for complete removal of all layers of treatment and reaching upto old plastered surface and applying a coat of wall care putty not less than 1mm thick as per manufacture instructions and applying two coats of oil emulsion paint over a coat of primer complete all as specified and directed.

Material and labour for preparing surfaces old plastered surfaces of walls and applying one coat of white washing complete as all specified and directed.

Preparation of old treated surfaces (Plastered or un-plastered) of ceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts, treating oil and greasy spots etc. and applying one coat of white wash on ceiling, complete all as specified and directed.

Material and labour for preparation of old wood and wooden based surfaces of any description not otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel complete all as specified and directed.

Material and labour for preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Taking down cement plaster on brick or stone walls or concrete surfaces, etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-charge.

Material and labour for 5mm thick rendering in cement mortar in (1:3) as in ceiling surface and finished the surface even and smooth without using extra cement including preparation new plastered surface and applying three coat of white wash complete all as specified and directed.

Demolition of lime concrete or cement conrete of any description and in any position as of sunken portion complete all as specified and directed.

Demolition of Cement Concrete as in G.F & paving n. exc. 15cm thick (above or below G.L.) complete all as specified and directed.

Material and labour for 50 mm thick PCC 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) as in plinth protection finished fair and even smooth without using extra cement complete all as specified and directed by Engineer-in-charge. Note:- The plinth protection shall be laid in panels and lenth of each panel shall not be more than 2.00 m all as directed 6mm joints filled with 85/25 grade bituman and sand in the ratio (1:3) shall be provided.

Material and labour for rendering 10 mm thick in CM 1:3 and mixed with and including integral waterproofing compound @ 3% by weight of cement and applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning of surface complete all as specified and directed.

Material and labour for cement concrete in foundations, filling and mass concrete Type E2 1 : 5 :10 using 40 mm graded aggregate as in sunken floor complete all as specified and directed.

Material and labour for cement concrete in foundations, filling and mass concrete Type C2 1 : 3 :6 using 40 mm graded aggregate as in under sunken floor complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engr-in-Charge.

Material and labour for brick work with sub class 'B' (old size) bricks, straight or curved on plan, exceeding 6 mtr mean radius built in CM 1:6 etc complete all as specified and directed.

Material and labour for brick work built in CM (1:6) straight or curved on plan exceeding 6 metre mean radius using sub class ‘B’ bricks (Except bricks) complete all as specified and as directed.

Material and labour PCC 1:2:4 type B1 using 20mm graded stone aggregate as in coppings, benching, kerbs, edges etc including necessary form work complete all as specified and directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed or layer in cement mortar (1:4) including dismantling of existing tiles etc including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, 7 to 8 mm thick as in vertical surfaces such as dado, skirting, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 10 mm thick rendering in cement mortar (1:4) including dismantling of existing tiles etc including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Material and labour for premium quality coloured glazed ceramic tiles (300x 450x 7 to 8mm thick) as in vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the shade of tiles over and including rendering 10mm thick in cement plaster 1:3 finished rough surface to receive tiles including dismantling of existing wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Material and labour for 15 to 18mm thick Granite stone of black shade work (table rubbed, polished & moulding), as in floors, cooking platforms and like bedded with and including 15 mm thick screed bed in CM (1:4) and jointed with grey cement slurry @ 3 Kg/Sqm, and pointed with white with admixture of pigment to match with shade of granite stone including grinding and polishing including dismantling of existing stone slabs including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Material and labour for 15 to 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, skirting, on vertical surface and like in 10mm thick rendering in CM (1:3) and jointed with grey cement slurry @ 3 Kg/Sqm, and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding, moulding and polishing on edges etc including dismantling of existing stone /tiles etc including cement mortar bedding and rubbish off the premises complete all as specified and directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, 8 to 9 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed or layer in cement mortar (1:4) including dismantling of existing tiles etc including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.18 sqm but not exceeding 0.38 sqm, 8 to 9 mm thick as in vertical surfaces such as dado, skirting, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 10 mm thick rendering in cement mortar (1:4) including dismantling of existing tiles etc including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

S& F for heavy duty tiles (coloured),good grip series,size 400mm x 400 mm x 10 mm thick ,pattern as approved by Engr - in - Charge ,set , jointed and pointed in neat cement slurry @ 3 kg/square metre ,laid over and including 20mm thick (average thickness) cement mortar (1:4) bed complete all as specified and directed by Engineer- in - Charge . (Note: Design/pattern shall be as approved by GE/Engr -in-Charge at the time of execution)

Supply & fixing (in repair) of vitreous china wash hand basin white flat back of size 550x440mm including CI brackets and 15mm chromium plated pillar tapc ast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks, PVC connection 450 mm long having PTMT nuts and chromium plated waste coupling and making good to disturbed portion including 32 mm dia PVC waste pipe etc., complete all as specified and directed.

Supply and fixing in repair of vitreous china wash down water closet pedestal pattern (EWC), White including connection to trap and to flushing pipe with ‘P’ or ‘S’ trap, making good to floor, plastic water closet seat cover with mild steel chromium plated hinges and chromium plated jet spray with 1.5 meter flexible LDPE pipe jointed with pipe complete all as specified and directed.

S&F in repair 10 ltr PVC valve less, symphonic action typelow level flushing cistern , white/coloured , with inlet ball valve, float and handle including flush pipe of polyethylene of low or high density or PVC 32mm dia for low level cistern and brackets complete all as specified and directed .

Supply and fixing in repair of vitreous china squatting pan of orrisa pattern size 580 x 440 mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and foot rests of any pattern complete including provision of lime concrete bed and connection to flush pipe excluding flushing cistern, flush pipe and bracket and making good the disturbed area complete all as specified and directed.

Taking down chowkats or frames with shutter, area exceeding 1.50 Square metre and not exceeding 4.00 Square metre each (without taking off shutters from frames) and removing from site, including cutting holes in wall / concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish complete all as specified and directed.

Taking down chowkats or frames with shutter, area not exceeding 1.50 Square metre (without taking off shutters from frames) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish complete all as specified and directed.

Taking down old unservicable wooden shutter of any descritption exceeding 1.00 sqm each but not exceeding 2.00 sqm each and removal from site including iron mongry, complete all as specified and directed.

Taking down shutter of any description exc 1.00 sqm but n.exc 2.0 each and refixing in same opening after necessary repair/easing and adjusting complete all as specified and as directed.

Supply and fixing 18mm thick PVC sheet having one side decorative laminated sheet all required brackets SS screws etc. the panel shall be fabricated using adhesive and screws where ever required.all the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification including fitting i.e. magnetic catcher as approved by Engineer -in-Charge.

Supply and fixing for lipping 1-1.5 mm thick 18 mm wide colour of approved design & color , fixed with solvent cement or head less nails to PVC door complete all as specified and directed

Supply and fixing continous (Piano) type hinges mild steel bright finish or lectro galvanised with wide of flaps 40mm complete all as spd and directed.

Supply and fixing 100 mm size hasp and staple,safety type,Stainless steel bright finish ,including bolt to hinge plate and fixed with screws,complete all as directed.

Supply and fixing of stainless steel (ISI Mark) barrel tower bolts of size 100mm long complete all as specified and directed.

Supply and fixing of stainless steel (ISI Mark) handles of size 100 mm long complete all as specified and directed.

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made

All as per item No 46 here in before but size 65x125mm complete all as specified and directed.

Supply and fixing 100mm long stainless steel butt hinges complete all as specified and directed.

Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Material test certificate and authentication should be compulsory provided by the manufacturing company : (Note: stainless steel butt hinges and necessary SS screws shall be paid separately)

Supply and fixing of winodws made of pre-painted steel (base steel as per IS 513 of 0.58mm thick "D" quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 micron thick, finish painted with a polyester paint of 12-16 micron thick and back coated with 5-7 mircon thick alkyd backer. Section for outer frame should be of 72x55 mm, centre mullion shoud be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 52x25 mm with concealed bracket. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20mm provision for guard bars/grills. Fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullion to be fixed with mullion cap. Shutter brackets with a in built PVC lip to be fixed in a way that the lip overlaps the shutter corners and are not exposed. Stay of 150mm long & 75mm handles 2 Nos of heavy duty stains less steel pivot hinges shall be provided per shutter. The winodos should be paneled with 4mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grades.) .Rubber gaskets are provided all around the glass. The above frames should be fixed to concert/masonary wall by means of self expanding screw. Including 10mm square bars with 6" (152.4mm) pitch complete for finished items for work including of all taxes. Note :- AC/Cooler opening will be provided as per std size/directed by Engineer-in-Charge.

Supply and fixing of stainless steel (ISI Mark) barrel tower bolts of size 150mm long complete all as specified and directed.

Supply and fixing of stainless steel (ISI Mark) handles of size 150 mm long complete all as specified and directed.

Supply and fixing of 250 mm stainless steel (ISI Mark) sliding door bolt, with hasp, staple (bolt type) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt complete all as specified and as directed.

Material and labour for Providing and Fixing of vajra series windows made of pre-painted steel (Base steel as per IS 513 of 0.58 mm thick “D” Quality galvanized as per IS 277 with Zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 48x50mm, centre mullion should be of 48x50mm, section for shutter should be of 52x 25mm and rebate for Glazed shutter with a 20mm provision for Guard bars/Grills. The sections are to is to be fixed with mullion cap. Handle, stay, 2 Nos. of Stainless Steel heavy duty Pivot hinges shall be provided per shutter the windows fitted with 4mm thick plain float glass with rubber gaskets including fixing the frames in concrete/masonry wall by means of self expanding screws, Including fixed panel beading section should be of 12x12mm. Outer frame and mullions to have 10mm Square guard bars with 6” (152.4mm) pitch etc., complete for finished item of work. Note :- AC/Cooler opening will be provided of standard size / as size specified by Engr in Charge.

Supply and fixing of three shutter vajra series Sliding Windows made of Pre Painted Steel and Galvanised Steel (Base Steel as per IS 513,D quality ,galvanised as per IS 277 with zinc of 120 GSM),using factory made section powder coated with pure polyester powder up to 50-60 microns thick with total coated thickness of 0.58mm for outer frame and 0.58mm thickness for Sliding Shutter Section,the outer frame for three tracks with grill provision size of 107mm x 44 mm and the window shutter section of 58 mm x 36 mm and the outer frame with two integrated guide tracks of 12mm width and 24mm deep for provision to slide the shutter / sash frame and also have a groove of 21mm x 5mm to provide additional track and facilities with a water drain outlet component made of PVC and the shutter frame fitted with 5mm thick plain float glass of reputed make and fixed with EPDM weathering seal resistant accessories and handle made of aluminium 1 Nos per each shutter and cut to length mitre jointed with corner brackets including installation of window system at site using anchor fasteners ,inclusive of conveyance of all materials accessories ,labour charges and erection at site with complete finished item of work . Note :- AC/Cooler opening will be provided of standard size / as size specified by Engr in Charge.

Supply and fixing in repair factory made steel ventilator with top hung shutters including box type hinges with steel handle and steel peg stay complete with glazing bars including PCC (C-O,1:3:6 using 12.5 graded aggregates) bed blocks for hold fasts if required all as specified and directed by Engineer-in-charge.

All as per item 56 herein before but as in ventilator top hanging shutter without glazing bar including PCC (C-O,1:3:6 using 12.5 graded aggregates) bed blocks for hold fasts if required all as specified and directed by Engineer-in-charge.

Material and labour for providing and injecting chemical emulsion of Imidacloprid 30.5 SC for Post construction Anti Termite Treatment along the external wall on the junction of wall and floor below concrete or masonry apron using emulsion @ 2.25 litre per metre ,300mm apart and 300 mm depth including drilling and plugging 12mm dia holes with white cement to match the existing floors complete all as specified including excavating channel along the wall and rodding etc. complete all as specified and directed. Note : Quantity will be measured perimeter of wall x depth of penetration.

Material and labour for providing and injecting chemical emulsion of Imidacloprid 30.5 SC for Post Construction Anti Termite Treatment along the internal wall on the junction of wall and floor using emulsion @ 1 litre per hole,300mm apart and 300 mm depth including drilling and plugging 12mm dia holes with white cemnt to match the existing floors complete all as including drilling and plugging 12mm dia holes with white cement to match the existing floors complete all as specified including excavating channel along the wall and rodding etc. complete all as specified and directed. Note : Quantity will be measured perimeter of wall x depth of penetration.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-charge.

Supply and fixing Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repair drapery curtain rod, mild steel, powder coated 25mm dia with brackets, knobs, end stops etc all as specified and directed by Engineer - in - Charge .

Supply and fixing stainless steel wire cloth, 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden beads supplied with shutters complete all as specified and directed by Engineer-in-charge.

Supply and fixing of 4 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane with oil putty or fixed with beads complete all as specified and directed. NOTE:-Glass will be fixed up to 12 Mtr height bldgs.

Supply and fixing in repairs stainless steel wire cloth, 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden beads supplied with shutters complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repair of sheet glass 4 mm thick, ordinary quality and glazing with oil putty, in square not exceeding 0.5 Sqm each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified and as directed . NOTE:-Glass will be fixed up to 12 Mtr height bldgs.

Supply and fixing in repair of 4 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane with oil putty or fixed with beads complete all as specified and directed. NOTE:-Glass will be fixed up to 12 Mtr height bldgs.

Material and labour for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Material and labour for 15 mm thick rendering in cement mortar (1:6) on surface of any description of brick or concrete and finished the surface even and smooth without using extra cement including preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over and including 1mm thick birla wall putty on wall complete all as specified and directed.

Material and labour for 15mm thick rendering in cement mortar (1:4) on surface of any description of brick or concrete and finished the surface even and smooth without using extra cement with and including two coats of cement base paint over a coat of primer complete all as specified and as directed.

Material and labour for rough cast plaster with and including 15mm thick rendering in CM 1:3 on brick wall or concrete surface as specified in clause 14.22 of SSR Part-I complete all as specified and directed. Note:-(i)After applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (which is generally of size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even. (ii)The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregates are thoroughly covered over and including two coats of cement base paint over a coat of primer complete all as specified and as directed.

Supply and fixing in repair of PVC (SWR) floor trap, plain with grating including jointing with solvent cement of outer dia metre outlet of 75 mm complete all as specified and directed.

Supply and fixing PVC (SWR) 110 mm pipe type A single socket in any length with rubber ring joints fixed to walls including dismantling of existing pipes of any description any length complete all as specified and as directed.

Supply and fixing PVC (SWR) 75 mm pipe type A single socket in any length with rubber ring joints laid in floors or trenches including dismantling of existing pipes of any description any length complete all as specified and as directed.

Supply and fixing 110mm dia stack clamps made out of 50mm by 5mm flat iron and 16mm dia around iron stays,including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

Supply and fixing in repairs of PVC (SWR) bends 110 mm bore complete all as specified and as directed.

Supply and fixing in repairs of PVC (SWR) bends 75 mm bore complete all as specified and as directed.

Supply and fixing in repairs of 110 mm bore PVC (SWR) junction single T (equal or unequal), including jointing with solvent cement, complete all as specified and directed.

Supply and fixing in repairs of 75 mm bore PVC (SWR) junction single T (equal or unequal), including jointing with solvent cement, complete all as specified and directed.

Supply and fixing in repairs of 110 mm bore PVC (SWR) vent cowl complete all as specified and as directed.

Supply and fixing of water storage tank of 500 ltr capacity, HDPE triple layer, cylindrical, vertical with closed top and FDA approved, 100% UA stabilized, rust proof, ISI marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, ISI marked, screwed and suitable for iron pipe 20 mm bore including taking down of old tank of any descrption and removal from site complete all as specified and directed. Note:- Tank shall be white and make of tank shall be engraved on the tank.

Supply and fixing of water storage tank of 1000 ltr capacity, HDPE triple layer, cylindrical, vertical with closed top and FDA approved, 100% UA stabilized, rust proof, ISI marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, ISI marked, screwed and suitable for iron pipe 20 mm bore including taking down of old tank of any descrption and removal from site complete all as specified and directed. Note:- Tank shall be white and make of tank shall be engraved on the tank.

Supply and fixing in repairs PVC waste pipe for wash hand basin / kitchen sink of dia 32/40 mm of required length at site complete all as specified and as directed.

Supply and fixing in repair of 75/100 mm dia CP grating any type fixed in floor and jointed in CM 1:3 complete all as specified and as directed.

Supply and fixing in repair of tanks cover with locking arrangement as per sample for 500 litre capacity PVC water storage tank complete all as specified and as directed.

Supply and fixing in repair of tanks cover with locking arrangement as per sample for 1000 litre capacity PVC water storage tank complete all as specified and as directed.

Supply and fixing in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide and chromium plated brakects guard and railing 60cm long complete all as specified and directed.

Supply and fixing in repair of stop valves, 15 mm dia, chromium plated, fancy type, ISI marked, screwed down, high pressure with capstain head, (concealed type) with long shank, screwed both ends for iron pipes or for unions, complete all as specified and directed. (Note : Weight of stop valve shall not be less than 0.575 Kg)

Supply and fixing in repair of stop valve 15mm dia, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified and as directed.

Supply and fixing in repair of stop valve 20mm dia, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified and as directed.

Supply and fixing in repair of 15 mm dia fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

Supply and fixing, in repair of WHB mixer (hot & cold), cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with long screwed shanks and fly nuts, fancy type screwed for iron pipe and fixed bore of pipe 15 mm, complete all as specified and directed.

Supply and fixing in repairs 15mm bore CP Angle cock one way chromium plated, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified .

Supply and fixing in repair of 15 mm dia bib taps, cast copper alloy with flange, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

Supply and fixing in repair of 15 mm dia bib tap sink cock regular spout with flange complete all as specified and directed.

Supply and fixing in repair of wall mixer with L bend (Provision for over hand shower) (hot & cold), cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with long screwed shanks and fly nuts, fancy type screwed for iron pipe and fixed bore of pipe 15 mm, complete all as specified and directed.

Supply and fixing for Aluminium door stopper of any descripion all as specified and directed by Engineer-in-charge.

Supply and fixing door seal PVC 30mm wide with foam complete all as specified & directed by Engineer-in-Charge.

Supply and fixing in repair of PVC connections 60 cm long and 15mm dia with PTMT nuts and PVC washers on both ends, complete all as specified and as directed.

Supply and fixing in repair of PVC connections 45 cm long and 15mm dia with PTMT nuts and PVC washers on both ends, complete all as specified and as directed.

Supply and fixing in repair of CP brass tubular towel ring, 150 mm dia fixed with CP brass screws complete all as specified and as directed.

Supply and fixing in repair of flush pipes to pedestal pan, including all joints complete all as specified and as directed.

Supply and fixing in repair of PVC seat cover (for EWC / Anglo Indian type WC complete all as specified and as directed.

Supply and fixing in repair of PVC coloured bath cabinet overall size 400 x 500 mm decorative design with looking mirror complete all as specified and as directed.

Supply and fixing in repair of chromium plated towel rail 600 mm long complete all as specified and as directed.

Supply and fixing in repair of Chromium plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union with shower arm complete all as specified and as directed.

Supply and fixing in repair of pegs set of 6 Nos, power coated GI fixed with cadmium plated screws complete all as specified and as directed.

Supply and fixing in repair of stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Supply and fixing (in repair) stainless steel sink with drainage board 1.00 mm thick, ISI marked for kitchen with plug, waste PVC pipe, washers including cantilever cast iron brackets, connecting union waste pipe with drainage board over all size 915 mm x 460 mm with bowl size 410 mm x 330mm x 160 mm etc; complete all as specified and directed.

Supply and fixing in repair of stainless steel plate rack 1 mm thick of size 750 x 600 x 200 mm weighing not less than 5 Kg each fix with stainless steel screw to wall, complete all as specified and directed.

Supply and fixing of GI tubing, 15mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing whereever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed.

Supply and fixing of GI tubing, 20mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing whereever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed.

Supply and fixing Chlorinated PVC (CPVC) pipes 20 mm outer dia, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.0 m spacing . this includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete all as specified and directed. Make : Supreme/Vectus or Equivalent

Refixing old serviceable steel water tubing of 15 mm bore, in new or old position, any grade, including Supply and fixing new fittings as required, fixed to walls and ceilings or laying in floors including necassary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing whereever required , including taking down of old tubing as existing at site and removal, complete all as specified and as directed.

Refixing old serviceable steel water tubing of 20 mm bore, in new or old position, any grade, including Supply and fixing new fittings as required, fixed to walls and ceilings or laying in floors including necassary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing whereever required , including taking down of old tubing as existing at site and removal, complete all as specified and as directed.

Supply and fixing in repair of 20 mm bore ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

Cleaning and removing all scale and dirt, etc from existing water storage tanks of capacity exceeding 250 litres and not exceeding 500 litres by emptying, drying and cleaning the tank by scrubbing the dust with wire brush from tank including cleaning from mouths of circulating pipes, to entire satisfaction of Engr-in–chargeof cleaning , including writing date of cleaning with oil paint of of visible colour in font size not less than 100 mm, complete all as specified and directed (The rates includes for disconnecting of existing water tank, lowering if required and hoisting, reconnecting and refixing in same position after cleaning ) NOTE: - (i) The whole process of disconnecting, reconnecting and refixing in same position after cleaning shall be done on the same day, if failing so, Rs. 100/- shall be deducted for each tank per day from the contractor due. (ii) A separate register to be maintained by contractor for cleaning and occupant signature with date to be obtained in it.

Cleaning and removing all scale and dirt, etc from existing water storage tanks of capacity exceeding 500 litres and not exceeding 1000 litres by emptying, drying and cleaning the tank by scrubbing the dust with wire brush from tank including cleaning from mouths of circulating pipes, to entire satisfaction of Engr-in–chargeof cleaning , including writing date of cleaning with oil paint of of visible colour in font size not less than 100 mm, complete all as specified and directed (The rates includes for disconnecting of existing water tank, lowering if required and hoisting, reconnecting and refixing in same position after cleaning ) NOTE: - (i) The whole process of disconnecting, reconnecting and refixing in same position after cleaning shall be done on the same day, if failing so, Rs. 100/- shall be deducted for each tank per day from the contractor due. (ii) A separate register to be maintained by contractor for cleaning and occupant signature with date to be obtained in it.

Dismantling of ceiling boards (fibre, pulp, insulation, etc.) or insulation boards /slabs/ blankets, any thickness, including cover fillets, as in false ceiling etc complete all as specified.

Supply and fixing of anodised GI snap grid frame work for false ceiling grid 605x605 mm fixed with Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including Supply and fixing Gypsum Board 12mm thick as in ceilings fixed with screws as per manufactures instructions including taking down existing false ceiling any type including grid etc complete all as specified and directed. NOTE : - Unit rate quoted against this item shall also include the taking down any electrical board, fittings etc effected for removing and refixing after repair work includes making good etc complete all as specified and directed.

Supply and fixing of semi perforated false ceiling 12 mm thick with micro tegular edged at all height with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of size 595 x 595 mm of approved texture, design and pattern having moisutre content less than 2%, humidity resistance of 99%, NRC 0.60 to 0.85 as per IS 8225-1987, non combustible as per BS 476 (Part-4) 1970 and light code description unit code No 429 Sub Head 26. New Technologies and materials reflectance of 85% minimum to be laid in true horizontal level suspended on interlocking metal T -grid of hot dipped galvanised iron section of 0.33 mm thick ( galvanised @ 120 gms/ sqm including both sides) comprising of main T- runners of size 15x 32mm of length 3000mm, cross T of size 15 x32 mm of length 1200mm and secondary intermediate cross T of size 15 x 32 mm of length 600 mm to from grid module of size 600 x 600 mm, suspended form ceiliing using galvanised mild steel items (Galvanised @ 80 gm/sqm) i.e. 50 mm long, 8mm outer diameter M-6 dash fastners, 6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of size 85 x 25 x 2mm. galvanised iron perimeter wall angle of size 24 x 24 x 0.4 mm of length 3000 mm to be fixed on perimeter wall / partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long dry wall SS screws. The work shall be carried out as per specification, drawing and as per direction of the Engineer-in-Charge including dismantling existing asbestos/PVC/ metal / Gysum sheet false ceiling textile coverings including frames (if any) and cover fillets complete all as specified and directed. NOTE : - Unit rate quoted against this item shall also includes taking down and refixing the same of any electrical board, switch, sockets, light and fittings, fans etc after carrying out necessary relevant work and making good to match with existing surface effected for this area etc complete all as specified and directed.

Material and labour for re-securing/ adjusting existing false ceiling grid, any type and make are required tightening to remove sag portion/ depression in false ceiling grid including replacement of missing sections / part/ suspenders as per existing size etc complete all as specified.

Supply and fixing missing / damaged perforated ceiling boards in existing grid as per existing size and incl painting required on front face including taking down damage/Bkn board etc complete all as specified and directed.

Supply and fixing missing / damaged metal ceiling boards in existing grid as per existing size including taking down damaged/Bkn boards etc complete all as specified and directed.

Supply & fixing in repair Steel tube of 50 mm bore, medium grade galvanized, ISI marked , fixed to walls as in addn support of ceiling , etc including cutting & chasing in wall and making good with PCC to old existing surface complete all as specified and directed .

Supply and fixing in repair of brass Spindle with cap / without cap suitable for 15mm dia CP tap/Cp Stop cock (short/long body/CP pillar taps as per sample to match the existing fittings as per site requirement complete all as specifried and directed.

NOTE:- Amount of credit of Rs.97,866.50 for retrieved materials is mentioned in Schedule of Credit Page No 19 & 20 of tender documents in pdf form which will be deducted offline while acceptance of tender.

AMIT LAMBA (BID ID -3269215)

M/s Gautam Electro Engineers (BID ID -3269670)

R.D Builders (BID ID -3264807)

G8 CONSTRUCTIONS (BID ID -3264444)

Parveen Kumar (BID ID -3264884)

Gupta Enterprises (BID ID -3264357)

m/s parmod kamar (BID ID -3264876)

power house batteries (BID ID -3265023)