SPECIAL REPAIR TO JCO MESS BLDG NO P-9/1 OF 119 (I) INF BDE CAMP, PROVN OF 02 NOS SENTRY POSTS AT RANE ENCLAVE AND PROVN OF BUS STAND NEAR ARO GATE AT 7E AREA AT MIL STN PITHORAGARH

Amount

DESCRIPTION OF ITEMS

Taking down old cement plaster of any description on brick or stone wall/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc complete as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) exc 1.5 Sqm but n.exc 4 Sqm each complete all as specified and directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) n.exc 1.5 Sqm each complete all as specified and directed.

Providing cement concrete 25 mm thick type B-0 (1:2:4) using 12.5 mm graded agg as in sub base to flooring .

Dismantling of floor, hearth or wall tiling /Paving blocks including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and as directed

M & L, non skid joint free coloured ceramic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm, over and including 15 mm thick screed bed in CM 1:6 as in floor etc set & jointed in neat cement slurry and pointed in coloured cement to matchth or wall tiling complete all as specified and directed

M & L, Vetrified tiles 7 to 8 mm thick area of each tile 600mm x 1200mm , in floors incl skirting over and including 15 mm thick screed bed in CM 1:6 as in floor etc set & jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed

M&L Glazed coloured ceramic tiles 600 x 300 x 7 mm to 8 mm thick on vertical surfaces, set and jointed in neat cement slurry and pointed in coloured cement to match colored tiles over and including 10mm thick in CM (1:4) on brick or concrete surfaces of finished rough to receive the glazed tiles in walls all as specified and directed by engg-in-charge

S&F non skid tiles, exterior grade, chequered/grooved pattern of size 600x600mm 8-10mm thick set and jointed in neat cement slurry and pointed in white/ coloured cement to match the shade as in floor over and incl 15mm thick cement screed bed in CM 1:4 complete all as specified and as directed.

M&L for Kota stone slab for stair case flooring 16-18 mm thick and including 20mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror finshed polishing in complete all as specified.

M&L for kota stone slab 16-18 mm thick in riser and thired single piece on steps, skirting, dado and pillar laid over and including 10mm thick rendering in CM 1:4 including grinding and mirror finshed polishing complete all as specified and directed.

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces on wall in CM 1:6 finished the plaster surfaces fair and even complete all as specified and directed.

Ditto as ier item no 13 but in cm 1:4 (external surfaces)with water proofing treatment compound. Note: WPC shall be measured and paid separately.

M&L for 5 mm thick rendering in CM 1:4 on ceiling, soffits, chajja projection etc complete all as specified and directed.

M&L for applying two coat OBD on newly plastered wall with airless electric sprayers over a coat of primer applied using airless electric sprayers electrically operated sanding machine. application tobe done through the authorised applicator of manufacturer complete all as specified and directed.

M&L for complete removal of existing treatment using mechincal device and applying of two coat OBD on wall with airless electric sprayers over a coat of primer applied using airless electric sprayers over sanded with electrically operated sanding machine. application tobe done through the authorised applicator of manufacturer complete all as specified and directed .

M&L for applying two coat OBD on newly plastered ceilling with airless electric sprayers over a coat of primer applied using airless electric sprayers sanded with electrically operated sanding machine. application tobe done through the authorised applicator of manufacturer complete all as specified and directed.

M&L for complete removal of existing treatment using mechincal device and applying of two coat OBD on ceilling with airless electric sprayers over a coat of primer applied using airless electric sprayers sanded with electrically operated sanding machine. application tobe done through the authorised applicator of manufacturer complete all as specified and directed

M&L for applying two coat exterior emulsion paint (weather coat of Berger or equivelent ) on newly plastered wall with airless electric sprayers over a coat of primer applied using airless electric sprayers sanded with electrically operated sanding machine. application to be done through the authorised applicator of manufacturer complete all as specified and directed..

M&L for complete removal of existing treatment using mechincal device and applying two coat exterior emulsion paint (weather coat of Berger or equivelent ) on old plastered wall with airless electric sprayers after prepearing old surface applied using airless electric sprayers sanded with electrically operated sanding machine. application to be done through the authorised applicator of manufacturer complete all as specified and directed..

Providing and applying plaster of paris putty of 1 mm thickness over plastered surface of wall/ceiling to prepare the old /new surface even and smooth complete all as specified and directed..

S&F factory made single extruded WPC (Wood Polymer Composite) solid door frame/chowkat of size 125x63 comprising of virgin PVC polymerof K value 58-60 (suspension Grade), Calcium Carbonate and natural Fibers (wood Powders/rice husk/wheat husk) and Non toxic additives (maxtoxicity index of 12 for 100 gms) fabricated with mitred joints and applying PVC solvent cement and screwed with full body treaded star headed SS screws having min frame density of 750 kg/cum screw withdrawal strength of 2200 N (face) & 1100 N edge, miniumum compressive strength of 58 N/mm2, moduus of elasticity 900N/mm2 and resistance tto spread of flame of class ‘A’ category with property of being termite /borer proof, water/moisture proof & fire retardant & fixed in position with SS dash fasterns/hold fast of required dia and length, colour of door frame to match that of shutter all as specified and directed. S&F factory made single extruded WPC (Wood Polymer Composite) solid door frame/chowkat of size 125x63 comprising of virgin PVC polymerof K value 58-60 (suspension Grade), Calcium Carbonate and natural Fibers (wood Powders/rice husk/wheat husk) and Non toxic additives (maxtoxicity index of 12 for 100 gms) fabricated with mitred joints and applying PVC solvent cement and screwed with full body treaded star headed SS screws having min frame density of 750 kg/cum screw withdrawal strength of 2200 N (face) & 1100 N edge, miniumum compressive strength of 58 N/mm2, moduus of elasticity 900N/mm2 and resistance tto spread of flame of class ‘A’ category with property of being termite /borer proof, water/moisture proof & fire retardant & fixed in position with SS dash fasterns/hold fast of required dia and length, colour of door frame to match that of shutter all as specified incl SS hinges and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door frame/chowkat of size 100x50 comprising of virgin PVC polymerof K value 58-60 (suspension Grade), Calcium Carbonate and natural Fibers (wood Powders/rice husk/wheat husk) and Non toxic additives (maxtoxicity index of 12 for 100 gms) fabricated with mitred joints and applying PVC solvent cement and screwed with full body treaded star headed SS screws having min frame density of 750 kg/cum screw withdrawal strength of 2200 N (face) & 1100 N edge, miniumum compressive strength of 58 N/mm2, moduus of elasticity 900N/mm2 and resistance tto spread of flame of class ‘A’ category with property of being termite /borer proof, water/moisture proof & fire retardant & fixed in position with SS dash fasterns/hold fast of required dia and length, colour of door frame to match that of shutter incl SS hinges all as specified and directed.

M&L for PCC 1:3:6 type C-1 using 20mm graded stone for embedding of hold fast etc complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid moulded flush door shutter pre-laminated both side of 30 mm size comprising of virgin PVC resin of K value 58-60 (suspension Grade), Calcium Carbonate and natural Fibers (wood Powders/rice husk/wheat husk) and Non toxic additives (maxtoxicity index of 12 for 100 gms) having min density of 650 kg/Cum and screw withdrawal strength of 1800 N ( Face) & 900 N (edge) Minimum Compressive strength of 50 N /mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category with property of being Termite/Borer proof, Water/Moisture Proof, Fire retardant and including with fixing stainless steel but hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer-in-Charge, Material test certificate and authenctication sould be complosory provided by the manufacturing company.

S&F Aluminium eyes pice glass for main Gate and shutter.

S&F for 30 mm thick factory made solid WPC (Wood plastic Composite) gauged door shutter with wire mesh in three number of division with brown wood gain texture, wire mesh fixed with (15 x 15) mm square tubes in side rails with screwing 8 x 28 heat metal zinc coated screws that can be removed or fixed again after changing and incl of wire mesh when needed covered with moulded beading. The density of the WPC material shall be as per manufacturer instruction. Complete all as specified and directed.

S&F Aluminium annodised barrel tower bolt of extruded section and fixed 200 mm size with bright bolt complete all as specified and directed.

S&F extruded Aluminium alloy handle fabricated annodised 150 mm size, complete all as specified and as directed .

S&F 300 mm long aluminium alloy annodised slidding door bolt with hasp and satple (bolt type) and fixing clips of sheet castor extruded sections and fixing bolts and slidding bolts of extruded section or cast aluminium alloy and fixed all as spd and directed.

S&F MS 300 mm ordinery rat rail rod pattern spring including roller and roller plate complete all as specified and as directed .

S&F 150mm long floor door stopper of aluminum alloy body and tongue , anodized with hard drawn steel spring complete all as specified and directed

M&L, preparing old previously treated surface of wood and wood based surfaces exceeding 10 cm in width or girth and applying one coat of synthetic enamel paint on old decorated wooden surfaces, complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fit-ted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube and fixing in opening as per specification complete all as specified and directed

S&F aluminium, anodised barrel tower bolts 150 mm long of extruded section and fixed complete all as specified and directed.

S&f aluminium handles 150mm size, cast type, anodised complete all as specified and directed.

S&F, butt hinges 100mm long, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, complete all as specified and directed.

S&F powder coated aluminium window , ventilator, shutters and kitchen cupboards, side hung type/ slidding type/Louvered Ventilator without sash bars, alumimium section weighing 0.55 kg/m including necessary joining cleats glazing clips, ruber packing, anodised aluminium snap beading screws anodised aluminium fittings such as ped stays 150mm long (1 No) hinges type B-21 100mm long (2 No) suitable handle (1 No) complete all as specified for add powder coating (minimum thickness of powder coating 50 micron)

S&F powder coated aluminium frame and shutter for doors and frame for windows, ventilators and partition with one or more rebates including joining cleat for fixing etc. complete all as specified add for powder coating (minimum thickness of powder coating 50 micron)

S & F Powder coated (Thickness or powder coating not less than 50 micron) anodised aluminium door shutters, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings Nos in each door, 2 hinges suitable handle ( 2 no.) complete all as specified

Supply and Fixing sheet glass 5.5mm thick ordinary quality and glazing with oil putty or rubber and aluminium beading in squares n. exc 0.5 sqm in each pane complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.35 mm nomonal dia of wire 1.18 mm avrage width of aperture ,fixed with tined tacks or galvanised wire staples complete all as specified and as directed.

S&F M.S Framed work such as grills gratings etc with ends of bars sholdered and/or riveted into spikes ,framed guard bars /railings all as directed .

M&L for RCC 1:2:4 type B-0 as in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like including demolition of existing RCC work complete all as specified and as directed.

Use and waste of form work to soffit of suspanded slab such as roof slab ,floor slab landing and similar work n exc 200mm thick (horizontally or sloping complete all as specified and as directed.

M&L for TMT bar 6 to 8 mm dia including cutting bending and binding with MS wire anealed dia not less than 0.9 mm conplete all as specified and as directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

M & L, Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour (as approved by GE) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws in single length complete all as specified and directed.

M & L Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of an colour (as approved by GE) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise proviceded for

S&F rolled mild steel section as in main and cross beams hip and jack rafters , purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates conforming to Fe-410, Gde E-250 all as specified and directed.

S&F for steel work as in tubelar truss incl special shaped washer etc complete using erw or induction butt weld ed tubes ,including gusset plate pole etc . all as specified and directed.

M & L, cement concrete 1:2:4 type B-2, using 40 mm graded stone aggregate as in surface channel or drain complete all as specified and directed.

M & L, forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitered / stopped ends etc. complete all as specified and directed.

S&F in repairs bib taps cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed for iron pipe or or brass ferrule for 15 mm bore of pipe.

S&F in repairs Stop valves cast copper alloy chromium plated fancy type with crutch or butterfly handle screwed down ,screwed for iron pipe or brass ferrule for 15 mm bore of pipe.

S&F in repairs concealed Stop cock chromium plated cast copper alloy fancy type with crutch or butterfly handle screw down ,screwed for iron pipe or brass ferrule for 15 mm bore of pipe.

S&F in repair 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed.

Supply & Fix in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding flushing cistern ) including connection to drain (or outgoing pipe) and to flushing pipe , antisyphonage pipe ,with PVC cover sheet in same colour etc complete all as specified and directed.

S&F in repairs PVC low level 10 litre capacity valveless syphonic action type flushing cistern including 32mm dia PVC flush pipe fixed in repairs complete all as specified and directed.

S&F in repairs Brass chromium plated Tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete.

S&F 1000 litres capacity rotational moulded polyethylene water storage tanks double layer (cylindrical vertical with closed top) hoisted and fixed in position including dismantling complete all as specified and directed

Taking up or down steel tubing 15 mm bore and connection including cleaning for refixing complete all as specified and directed.

Refixing old serviceable 15 mm GI tubing and connection in new or old position (concealed in Wall, ceiling & floor etc.) including necessary fittings & fixtures etc. complete all as specified and directed

S&F 15 mm bore tubes medium grade galvanised with all fittings and fixed to walls, ceilings or laid in floors incl cutting chases where required complete complete all as specified and directed

Taking up or down steel tubing 20 mm bore and connection including cleaning for refixing complete all as specified and directed.

Refixing old serviceable 20 mm GI tubing and connection in new or old position (concealed in Wall, ceiling floor etc.) including necessary fittings & fixtures etc. complete all as specified and directed

S&F 20 mm bore tubes medium grade galvanised with all fittings and fixed to walls, ceilings or laid in floors incl cutting chases where required incl taking down 20 mm bore steel tubing and connections complete complete all as specified and directed

S&F in repair 20mm Gate valves with iron wheel head screwed both ends for iron pipe and fixed.

S&F in repair table top Wash Hand Basin superior quality 550 x 400 mm size fitted and including 15 to 18 mm thick granite top over RCC slab incl waste coupling 150mm long complete all as specified and directed.

S&F in repair, Brass CP wash basin mixer(long nose)15mm bore dia for mixing Hot or Cold water screwed down for iron pipe and fixed all as specified and as directed.

S&F in repair, Brass CP wall mixer (long nose)15mm bore dia for mixing Hot or Cold water screwed down for iron pipe and fixed all as specified and as directed.

S & F in repair Soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and directed.

S&F in repair 5mm thick glass shelf/mirror self of size 600mm long fancy type fixed and including Chromium plated grils, screws and wooden /plastic cleats complete all as specified and directed

S&F in repair 6mm thick glass corner shelf assembly fancy type size 250mmx250mmfixed with and including chromium plates brass screws and wooden /plastic cleats complete all as specified and directed

S & F in repair Aluminium peg sets of 6 pegs complete.

S & F in repair Brass chromium plated shower rose 125mm size incl shower arm complete all as specified and directed.

S & F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S & F in repair brass chromium plated toilet paper holder fixed with brass screws complete all as specified.

Supply & Fix in repairs, 75mm bore PVC(SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches or in floors and fixed to wall with PVC holding clamps complete all as specified and directed.

S&F in repairs, 110mm bore PVC(SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches or in floors and vertical surfaces complete all as specified and directed.

S&F in repair 50mm PVC (SWR) pipes single socket in any length and including bends and sockets complete all as specified and directed

S&F in repairs, 125/110mm bore PVC (SWR) 'P’ trap complete all as specified and directed.

S&F in repairs, 75mm bore dia PVC floor trap (SWR) plain with grating including jointing with solvent cement to waste pipe complete all as specified and directed.

S&F in repairs, 110mm bore PVC(SWR) bends any radius, complete all as specified and directed.

S & F PVC (SWR) junction single,(Single T) equal or unequal 75 mm dia

S &F PVC (SWR) 75 mm dia vent cowl

Dismantling of stone slabs and tiles of any description or thickness in floors, approachs, dado/Partitions etc complete all as specified and as directed

M&L Granite (of any type of coloured) work (table rubbed and polished) 20 mm thick in steps jambs,pillars, window cills, cooking plateform /partition and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick screed bed in CM 1:6 incl moulding, chamfering of edges complete.

S&F in repairs PVC cabinet mirror size 350mm x 450mm fixed with steel screw with rowl plug complete all as specified and directed.

S&F in repairs C P Hand shower (health faucet) 1 mtr PVC tube with wall hook complete for EWC, all as specified and directed.

S&F in repairs Two way bib taps cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed for iron pipe or or brass ferrule for 15 mm bore of pipe.

S&F 15mm angle valve cast copper alloy screwed down high pressure fancy type chromium plated complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded Stone aggregate) as in plinth protection finisheed even and smooth without using extra cement complete all as specified.

M&L for precast cement concrete 1:2:4 type B-1, (using 20mm graded stone aggregate) as in manhole covers , shelves, chajjas etc and similar articles with plain faces set in CM 1:4 incl dismantling complete all as specified.

Demolition of precast concrete articles and pre-cast cement concrete block walling, ashlar fencings, dressed stone work including all quoins, arches, pillars etc. built in cement mortar complete all as specified and directed.

M&L, precast cement concrete Block Masonary with solid blocks type C1, 1:3:6 (20mm graded stone aggregate) exc 10 cm in width and setting in mortar 1:6 complete all as specified and directed .

M&L, providing cement concrete1:2:4 (20 mm graded aggregate) type B1 as in , coping ,benching, bressumers, steps, incl necessary form work and demolition of existing cement work complete all as specified and as directed.

S&F in repairs curtain rod made of SS pipe dia of rod 25 mm with decorative brackets and ends complete all as specified and as directed.

M&L for sunken floor treatment as described as under (i) to (vii):- (i) Demolition of cement concrete of any description and in any position not otherwise specifically Provided or in any type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed . (ii) M&L to fill the sunken floor with PCC (1:5:10) type E-2 using Brick aggregarte over the treated surface complete as directed . (iii) M&L 40mm thick (Min) PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate with integral water proofing compound as per manufacture instruction instructions on bottom of sunken portion with proper slope towards spout . Vertical sides shall be plastered in CM (1:3) 15mm thick mixed with water proofing compound as per manufacturer instructions .Plaster shall be extended over PCC coving when the same is green i.e. PCC & Plastger be carried out at the same time complete all as specified and directed. (iv) After laying sewage /Plumbing pipes with fixtures in position 2 coats of OMIPLAS EP -101 epoxy compound shall be applied complete all as specified and directed . (v) Spouts of 25mm dia GI pipe light grade projecting 450 mm clear of face outer a wall with mosquito proof cap on inner face of pipe shall be provided to drain out seepage water including cutting holes and making good if needed as specified and directed . (vi) Test again of water tightness by pounding for 72 hours & rectify defects if any till total elimination of defects complete all as specified and directed .the sunken portion shall be tested for leakage /seepage /dampness by pounding with water for 72 hours .in case any defect is noteced the portion shall be grounted with cement slurry mixed with suitable chemical & tested again .The process of grouting and testing shall be repeated till leakage /seepage /dampness is eliminated as specified and directed .

M&L, 18 to 20 mm thick Makrana white Marble work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including rounding exposed edges complete all as specified and as directed.

S&F in repair 20mm to 25mm thick Hard wood 2nd class weather boarding clean sawn and rebated on thick edge to give 25 mm laps and wrought both side and edges shot and chamfered fixed to roof hight of bldgs complete all as specified and directed .

S&F in repair stainless steel pipe 32 mm dia of grade 202 medium as in framed work such as sign boards/ railling etc including all necessary welding drilling or rivetings brackets stoopers complete all as spd and directed

Supply only water proofing compound ,complete all as specified and as directed.

M&L for 15 mm thick rendering on fair faces of concrete surfaces of roof as water proofing treatment in CM 1:4, including finishing the surfaces even and smooth, complete all as specified and directed.

M & L for water proofing treatment to roofs surfaces including a coat of applied bituminous shalitex primer @ 0.30 lit per sqm evenly on roof surface and a coat of hot bitumen 85/25 @ 1.2 kg/sqm shall be applied on primed surface and laying of 3mm thick APP modified polymeric membrane (weight not less than 3 kg/sqm) unrolled and bonded completly to the substrate with side overlap of 75 mm and end overlap of 100 mm and then sealed/fused by flame or bitumen and a coat of hot blown bitumen grade 85/25 @ 1.2 kg/sqm shall be applied on top of APP modified polymeric membrane as per manufacturer instruction and finally it will be finished with a coat of aluminium paint @ 0.20 kg/sqm ,complete all as specified and as directed .

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M & L for providing precast cement concrete bonders (for stone walling) type B1 (1:2:4) using 20 mm graded stone aggregate, set in Cement mortar 1:6 complete all as specified and directed

M & L for walling of random rubble, uncoursed well bounded, bedded and solidly hearted, built in Cement Mortar 1:6 complete all as specified and directed

M & L for walling (Except stone) of random rubble, uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:6 complete all as specified and directed

Hand packing (any thickness) at back of walls with broken stone or boulders and raising (or lowering) to the required level complete all as specified and directed.

M&L for raised pointing to randam polygonal rubble, uncoursed or brought upto courses in Cement mortar (1:4) complete all as specified and directed.

Excavation in trenches ,n exc 1.5m wide and n exc 1.5mtr in depth for foundation etc or for shafts ,well cesspts ,manholes etc n exc 10sqm on plan and n exc 1.5mtr in depth and getting out in hard soil complete all as specified and directed.

Returning, filling in, earth including spreading, levelling, watering and well ramming in layers n.exc 25 cm thick complete all as specified and as directed.

Removing excavated material n. exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point.

Demolition and breaking up drain pipes (Salt glazed ware ,AC or reinforced concrete ) det in cement mortar internal dia of pipe in 150mm to 200mm dia

M&L for 200 mm dia reinforced concrete pipes, class NP2 with one collar per length of pipe complete all as specified and as directed .

M&L for concrete bed to 200mm drain pipes including forming cradles in PCC 1:4:8 type D2 using 40 mm graded stone aggregate complete all as specified and as directed .

S&F in repair stainless steel pipe 50 mm dia of grade202 medium as in framed work such as sign boards/railling etc including all necessary welding drilling or rivetting brackest stoppers and including embediing the same in PCC 1:3:6 type c1 below ground level size of PCC (200 x 200 x 100 mm) including excavation in soft/disintegrated rock complete all as spd and directed

M & L for Cement concrete Type D2,1:4:8 using 40 mm graded aggregate as in foundations, filling and mass concrete .

M & L for Design Mix (M-25) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc.

M & L for Design Mix (M-25) as in Columns, pillars, piers etc.

M & L for Design Mix (M-25) as in roof beams, cantilevers,bressummers, lintels over 1.5m span

M & L for Design Mix (M-25) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter for fair finished surfaces in square/rectangular.

M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces in square/rectangular.

M & L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers,lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams or rough finished surfaces in square/rectangular etc.

M&l for brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

M & L for 50mm thick sand filling under floors or in foundations including watering and consolidation.

M & L for 75 mm thick cement concrete type C- 2, 1:3:6 (40mm graded aggregate) as in Sub base.

M & L for coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering in CM 1:4 and jointed white or colour cement to match.

S & F Steel ventilator with top hung shutter including hinges, steel peg stay, complete

S & F 5 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane

S & F 100 mm Butt hinges, medium weight, cold rolled mild steel, and fixed

S & F Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms)

S & F vitreous china wash hand basin, white, size 550 x 400 mm including brackets, chromium placted waste coupling &PVC waste pipe of 32 mm dia complete all as specified & directed..

S & F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe etc.

M & L fpr 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors.

M & L for 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors.

M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

S&f 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement.

S&F 110mm dia PVC (SWR) P Trap complete all as specified and directed.

S&f grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified.

S & F CP towel ring as a approved quality complete all as specified & directed

M&L for 100mm thick Plain Cement Concrete 1:4:8 type -D2 using 40 mm graded stone aggregate as in subbase of floors etc, complete all as specified and directed.

M&L for non skid ceramic coloured tiles of size exc 0.42 Sqm and n .exc 1 Sqm as in floor etc set and jointed in neat cement slurry and pointed with white cement and coloured pigment to match the tiles over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M & L for Polycarbonate sheet 6mm thick as in roof covering including bending to curve and including all cutting and waste complete all as specified and directed.

S & F 50x4mm thick Aluminium Flat strips with rubber gasket for covering of joints of polycarbonate sheetssealed with sealing joint sealant compound complete all as specified and directed.

Supply and fix stainless steel hollow rectangular pipes size 100mm x 50mm x 1.5mm thik dia of grade 202 medium as in Framed work such as sign boards /railing etc including all necessary welding ,drillngs or rivetting ,brackets ,stopers complete all as specified and directed.

Supply and fix stainless steel hollow rectangular pipes size 100mm x 50mm x 1.5mm thik of grade 202 medium as in Framed work such as sign boards /railing etc , all necessary welding ,drillngs or rivetting ,brackets ,stopers and including embedding the same in PCC 1:3:6 type C-1 below ground level size of PCC (45x450x600mm) including excavation in soft/disintegrated rock complete all as specified and as directed. complete all as specified and directed.

Supply and fix stainless steel hollow rectangular pipes size 50mm x 50mm x 1.5mm thik dia of grade 202 medium as in Framed work such as sign boards /railing etc including all necessary welding ,drillngs or rivetting ,brackets ,stopers complete all as specified and directed.

Supply and fix stainless steel hollow rectangular pipes size 15mm x 15mm x 1mm thik dia of grade 202 medium as in Framed work such as sign boards /railing etc including all necessary welding ,drillngs or rivetting ,brackets ,stopers complete all as specified and directed.

Taking down carefully Copper/Aluminium point wiring (Light ,fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants, regulators, sockets etc), removing unserviceable or serviceable materials from site and making good the disturbed surface of walls, floors etc, complete all as specified and directed.

M&L for point wiring Concealed with 1.5 Sqmm, single core (FRLS), PVC insulated with multistranded unsheathed copper conductor cable including rigid non- metallic PVC concealed conduit 20 mm or higher dia, medium grade ISI marked complete with required size of modular sunken box and Modular cover plate for mounting Modular switch, socket and regulator & all PVC conduit accessories / fittings and including continuous earth wire of PVC insulated, unsheathed, green in colour 1.5 Sqmm multistrand copper conductor (FRLS) connected to all fittings, common earth and connected to earth dolly , screwed with Brass screws, cup washers complete all as specified and directed for the following :- (a) One light point/Fan point controlled by one, one way switch of 5/6 Amps.

Ditto as per Item No 158 above but, (b) One 3/5 pin socket outlet 5/6 Amp on same board with other switch of 5/6 Amp.

Ditto as per Item No 158 above but, (c) One 3/5 pin 5/6 amps socket out-let point on independent board controlled by one, one way switch of 5/6 amps on independent board.

Ditto as per Item No 158 above but, (b) One light point controlled by two way switch of 5/6 Amps.

(e)All as per item 158 herein above but with 4.0 Sq mm cable (FRLS) for one 15/16 Amp socket outlet controlled by one switch on independent board and 4.0 Sqmm PVC insulated unsheathed multi stranded copper conductor cable as continuous earth wire complete.

S & F ,Modular Switch flush type, white finish, 5/6 amps, single pole, one way all as specified and directed.

S & F Modular Switch, white finish, 5/6 amps, single pole, two way all as specified and directed.

S&F Modular Switch, white finish, 15/16 amps, single pole, one way, complete all as specified and directed.

S&F Modular Socket outlet 3 pin, 5/6 amps and 2 pin 5/6 amps with sutter, complete all as specified and directed.

S&F Modular Socket outlet two in one 3 pin 5/6 amps and 3 pin 15/16 amps (multipurpose), with shutters, complete all as specified and directed.

S&F ceiling rose, surface bakelite, AC, 220/240 volts, 3 terminals, complete all as specified and directed.

S&F Lamp holder, insulated body with back plate suitable for batten /angular fittings, fixed on with & including round block 8 cm dia, 4 cm depth, closed recessed type & making connection etc complete all as specified & directed.

S & F Electronic fan regulator modular stepped type two module with five steps 240 Volts, 100 Watt suitable for 1200/1400 mm sweep AC ceiling fan complete all as directed by Engr-in-Charge.

Taking down ceiling fan 1200 mm sweep/Exhaut fan of any size complete cleaning the grease oil etc spray painting with 2 coats of synthetic emamelled paint over a coat of primer including replacement of bearing, capacitor, cotton pin, rubber coal, MS nuts bolts washer, connector prewired from connector from connector to ceiling rose with twin core flexible copper conductor cable 24/0.02 refixing in position connecting testing etc complete all as specified and directed.

Supply and Fixing in repair LED Bulk head Fitting environment friendly , IP-65/66, ultra modern,energy saving,surface mounting,decorative oval comprising of high brightness LED 10 Watt,6000 K complete all as specified and directed.

S&F in repair recess mounting LED 2x2 luminaire 36W,6500K slim ceiling light with extruded aluminium housing and milky diffuser complete and including taking down old fitting all as specified and directed.

S&F in repair inverter LED lamp, 6500K, 900lm in white colour of 12 Watt, base cap B-22 with polycarbonate diffuser and aluminium heat sink complete all as specified and directed.

Supply and fixing in repair LED Integrated Batten T5 box type surface mouted, (1x20 Watt,four feet long) prewired including electric electrical connection with PVC insulated twin twisted copper wire of size 0.75 Sqmm from ceiling rose to tube light fitting and including taking down old fitting complete all as specified and directed.

Supply and fixing in repair LED Integrated Batten T5 box type surface mouted, (1x10 Watt,two feet long) prewired including electric electrical connection with PVC insulated twin twisted copper wire of size 0.75 Sqmm from ceiling rose to tube light fitting and including taking down old fitting complete all as specified and directed.

S & F in repair 1x60 watt LED building security light fitting , PDC housing,IP-65 with 4 KV inbuilt surg protection driver, pressure die-cast aluminium including fixing the same of GI pipe 25 mm dia bore light grade bracket, 1.5 mtr long including necessary cutting / bending /welding and fixed the same with two Nos FI clamps of 40x 4mm duly painted and suitable size of nut & bolts etc. and making electric connection with PVC three core copper flexible wire complete all as specified and directed.

S&F Sub main wiring with two single run (with proper colour code as per IE rule) of 6 Sqmm (Normal cross sectional area) of single core unsheathed PVC insulated cable, 1100 volts grade multi stranded copper conductor drawn through with & including PVC conduit of 25 mm dia or higher dia medium grade ISI marked with and including necessary conduit accessories, concealed type including 6 Sqmm multi stranded copper conductor PVC insulated cable as earth wire(Green in colour) connected to common earth dolly, including taking down old U/S submain wiring complete all as specified and directed.

Material and Labour for earthing in repair complete with galvanized steel earth plate electrode 600 X 600 X 6 mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.50 m deep below normal ground level, connected to galvanized earth lead wire 4.0mm dia by means of bolts, nuts and washers of galvanised iron or steel all as shown in earth plate No 3 of MES schedule 2009 part – I connected to earthing test point including earth continuity conductor and loop earthing etc. as required 4 mm dia galvanized iron or steel wire including necessary excavation and earth work, concrete pit & chamber in PCC 1:2:4 type B1 & pit cover 75mm thck in RCC 1:2:4 type B1 duly reinforced with 6mm dia bar @ 150 c/c both ways including with lifting handle and Earth lead and GI protection pipe light grade 15 mm dia beyond 7.5 mtr from electrode to earth terminal point /main switch board and 20mm bore GI watering pipe medium grade etc. complete all as specified and directed.

S&F in repair Socket residual current device with socket plug top and MCB with a three pin earth plug and socket complete with on DP MCB 25 Amp complete all as specified and directed.

Supply and Fixing in repair MCB DB sheet metal enclosure for DB, TPN, 4 way having protection with 200 amps rated bus bar, 415 volts, made out of 16 guage sheet steel double door including grauting suitable for housing MCB's and isolators, complete all as specified and directed.

S&F in repair MCB DB sheet metal enclosure for DB, DP, 12 way having protection with 200 amps rated bus bar, 240 volts, double door type, suitable for housing MCB's and isolators,concealed in wall complete all as specified and directed.

Supply and Fix MCB single pole, 240 volts, 6-32 Amps of 10 KA C Curve complete all as specified and directed.

Supply and Fix MCB DP 240 volts, 40 amps, C Curve of 10 KA complete all as specified and directed.

S&F MCB Triple pole & Neutral 415 volts, 63 amps, C Curve of 10 KA complete all as specified and directed.

Supply install and tesing water heater storage type (Geyser) single phase 230 V, 50 Hz, 5 star energy saving high density PUF insulation tank made of heavy duty mangesium anode rod with steel core to protect enamelled tank from rust & corrosion, vertical installation type 25 Ltr Cap 2000 Watt rated power, incoloy 800 glass coated heating element, inner tank coating of feroglas powder, tank made of ultra thick super cold rolled steel plates, rated pressure 0.8 MPa, IPX4 protection consist of safety valves, thermal cut off, thermostat including connecting up and fixing arrangement on wall including providing hole fastners-04 Nos hot and cold water metallic flexible pipes 15 mm bore of adequate length as provided by OEM or required at site - 02 Nos non return valve 01 No and including necessary plumbing work, complete with intergated shock safe plug with all protection features as per OEM design and standard all as specified and directed.

S & F Exhaust fan metallic body, 450mm (14") sweep single phase 230 volts 50 Hz AC, 1400 RPM energy saving, heavy duty totally enclosed, heavy duty motor with die-cast aluminium rotor mounted on two ball bearings complete with louvers and shutters including cutting hole for fixing exhaust fan to wall and making good the disturbed surfaces (including making holes in wall, plastering, necessary brickwork and distempering) to match with teh existing specification, connecting electrically using 3 core 0.75 Sq mm PVC insulated flexible copper conductor cable over all sheathed all as required at site and as directed

Supply and laying in repair for XLPE LT 1100 volts underground earthed cable, PVC bedded, galvanized steel strip or wire armoured, electric power cable heavy duty 1100V with multi stranded, aluminum conductor of cross sectional area 2 core x 10 Sqmm including laying, testing and commissioning complete all as specified and directed.

Supply and fix in repair ON LOAD change over switch 415V in sheet metal enclosures box complete with all accessories like nut bolt connector etc 4 pole of capacity 63 Amps 3 phase 4 pole supply with side handle complete all as specified and directed.

S&f in repair for Factory Made sheet metal box with 4Nos of bus bar of capacity 100 Amps, single door hinged shutter and locking arrangement flashed/grouting on wall including necessary powder coated(Siemence gray) painting with after necessary preparation of surface , complete all as spacified and as directed.

S & F Exhaust Fan PVC body, 200mm(8") sweep, single phase, 230 volts 50 Hz AC,1400 RPM, energy saving, heavy duty totally enclosed, heavy duty motor with die-cast aluminiun rotor mounted on two ball bearings complete with louvers and shutters including cutting hole for fixing exhaust fan to wall and making good the disturbed surfaces (including making holes in wall,plastering, necessary brickwork and distempering) to match with the existing specification, connecting electrically using 3 core 0.75 Sq mm PVC insulated flexible copper conductor cable over all sheathed all as required at site and as directed.

basant ballabh punetha (BID ID -3336038)

LAXMI DATT & J C PANT (BID ID -3335236)

M/S HIRA CHAND (BID ID -3335034)

SHAHJEE FRIDGE SERVICE (BID ID -3336200)

SK Traders Sons (BID ID -3334637)

M/S RAMESH SINGH ADHIKARI (BID ID -3338822)

m/s bahadur singh samant (BID ID -3340659)

m/s vishnu kumar agarwal (BID ID -3335762)