GE/863/EWS-T-83/2019-20

Amount

Taking down chowkats or frames exc. 1.50 Sqm and n.exc 4.00 Sqm each with shutters (without taking off shutters from frames), complete all as specified and directed.

Taking down chowkats or frames n. exc. 1.50 Sqm each with shutters (without taking off shutters from frames), complete all as specified and directed.

Dismantling boarding, any description, fixed any position with screws complete all as specified and directed.

Dismantling floor, hearth or wall tiling inculding cement motar bedding (but not backing ) removing rubbish of the premises, complete all as specified and directed.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m deep and getting out in hard / dense soil complete all as specified and directed by Engr-in-Charge.

M&L for Returning, filling in, including spreading, levelling, watering, and well ramming in layers n. exc. 25 cm thick complete all as specified.

M&L for Removing excavated material (soil) n. exc. 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified.

M&L for Hardcore or broken stone or boulders of gauge n. exc. 63 mm, deposited, spread and levelled in layers n. exc. 15 cm thick, watered and rammed to a true surface complete all as specified.

M & L for Hard core, broken stone of boulders to gauge exc 63 mm and n. exc 100 mm complete all as specified and directed.

M&L for Cement concrete type D-2, 1:4:8 (40 mm graded stone aggregate) in foundation filling and mass concrete complete all as specified.

M&L for providing plain cement concrete type B1(1:2:4) using 20 mm graded stone agg as in kerb stones, plinth course etc. including necessary form work complete all as specified and directed.

M & L for providing, cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate in Lintel, mud stops, rounded or chamfered on edges complete all as speified and direted.

Material and labour for Pre-cast cement concrete block masonry with solid blocks,type C-1, 1:3:6 (using mechanically crushed 20 mm graded stone aggregate) exc. 10 cm in width and setting in cement mortar 1:6, complete all as specified and as directed.

M & L for precast reinforced cement concrete (1:2:4) type B - 1 using 20mm graded stone aggregate as in manholes covers, with plain fair faces including chamfers, weathering throttling etc and set in cement mortar (1:4) complete with joint to match including necessary form work, complete all as specified and as directed . Note : Reinforcement shall be measured and paid seperately.

M & L for precast cement concrete solid block masonary n. exc 10cm width made PCC 1:3:6 type C1 using 20mm graded stone agg and setting in CM 1:4 completed all as directed.

Material and labour Reinforced cement concrete 1:2:4 (using mechanically crushed 20 mm graded stone aggregate) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engr-in-Charge.

M&L for Reinforced cement conceret type B-1, 1:2:4 (20 mm graded aggregates), nominal mix in beams, cantilevers, bressummers, lintels complete all as specified.

Supply only integral waterproofing compound.

M&L for Walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified.

Use & waste of form work to soffits of suspended slab such as roof Slabs, floor slabs and similar work; n. exc 200mm thick (horizontal or sloping) all as specified and directed by Engr in Charge.

Use & waste of formwork to sides and soffits of floor or roof beam, lintels, shelves including supports complete all as specified.

Use & waste of form work to edges of concrete flats, floor and roofs n. exc 20 cm wide horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide complete all as specified and directed.

Supply & Fix Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed by Engr-in-Charge.

Supply & Fix Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and as directed by Engr-in-Charge.

S&F Aluminium, anodised, barrel tower bolts of length 200 mm of extruded section and fixed complete all as specified.

S&F Aluminium, anodised, barrel tower bolts of length 150 mm of extruded section and fixed complete all as specified.

S&F Aluminium, anodised, barrel tower bolts of length 125 mm of extruded section and fixed complete all as specified.

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as speified.

S&F 250mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as speified.

S&F Butt hinges of size 100 mm, medium weight, cold rolled mild steel and fixed complete all as specified.

S& F 100mm but hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodiesed and fixed.

S& F 125mm but hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodiesed and fixed.

S&F Aluminium handles of size 150 mm, cast type, anodised complete all as specified.

S&F Aluminium handles of size 125 mm, cast type, anodised complete all as specified.

S& F 4 levers mortice lock verticle type of size 100 mm complete all as specified and directed.

Supply & Fix CP towel rail 20mm dia, 60 cm long D type fixed with wooden gutty and steel screws complete all as specified and as directed by Engr-in-Charge.

S&F Door closer aluminium hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified.

Supply & Fix GI wire cloth 0.56mm nominal dia of wire and 1.18 mm average width of aperture complete with beads etc. for door shutter/window shutter of any size/ type/thickness complete all as specified and as directed by Engr-in-Charge.

M&L for Mild steel TMT bars 10 mm dia. and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified.

Supply and fixing TMT bar 8 mm dia, cut to length, bent to shape required including cranking, hooking ends and binding with and including mild steel (annealed) wire not less than 0.9 mm dia or securing with clips etc all as specified and directed.

M&L for Mild steel TMT bars 6 mm dia. and over upto and including 10 mm dia in stirrups, spaces and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified.

Supply & Fix Steel windows or ventilators, fixed type, with glazing bars complete all as specified and as directed by Engr-in-Charge.

S & F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F powder coated Anodised aluminium frame for doors, windows, ventilators & partition walls with one or more rebates including joining cleat for fixing etc. (thickness of powder coating 50 micron), complete all as specified

S&F anodiesed aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary jointing cleats,glazing clips,rubber neoprene packing, 200 mm long aluminium handle 02 nos in each shutter, 03 nos 100 mm hinges, anodised aluminium snap beading, screws etc. complete all as specified and directed.

S&F anodiesed aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary jointing cleats,glazing clips,rubber neoprene packing, 150 mm long aluminium handle 02 nos in each shutter, 02 nos 100 mm hinges, anodised aluminium snap beading, screws etc. complete all as specified and directed.

S&F powder coated Anodised aluminium grills of any pattern / design weight not less than 1.5 kg per sqm framed with U channel 20 x 20 mm complete all as specified and directed.

S&F 12mm Prelaminated particle board, interior grade, with prelaminated both sides with decorative choice laminations, fixed with screws to frame work complete all as specified and as directed.

M & L for 50 mm thick cement concrete (1:3:6) type C-1 using 20mm graded stone aggregate as in plinth protection, footpath and make concrete surface finished without using extra cement, complete all as specified and directed.

M&L for cement concrete type D-2, 1:4:8 (40 mm graded stone aggregate), 100 mm thick as in sub base of floor complete all as specified.

Material and labour for 75 mm thick cement concrete type D-2 1:4:8 (using mechanically crushed 20 mm graded stone aggregate) as in sub base all as specified and directed by Engr-in-Charge.

Material and labour 100 mm thick PCC 1:2:4, type B-2 (using mechanically crushed 40 mm graded stone aggregate) as in floors finished rough for receiving top layer complete all as s[pecified and as directed by Engr-in-Charge.

M & L for 25mm thick cement concrete type B-0 (1:2:4) using 12.5mm graded stone aggregate as in leveling course, complete all as specified and directed.

M&L for Glazed ceramic tiles, coloured, in vertical surfaces, 300 X 200 X 7 mm thick over and including 10 mm thick cement plaster in cement mortar 1:4 as backing of wall tiles etc., set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified.

Material & Labour glazed ceramic coloured tiles of size 450 x 300 x 7mm mm thick in vertical surfaces of wall etc over & including 10mm thick backing coat in CM (1:4) complete set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface complete all as specified and as directed by Engr-in-Charge.

Material & Labour for non skid ceramic coloured tiles 7 to 8 mm thick (Square/Rectagular) area of each tile exceeding 0.06 Sqm but not exc 0.11 Sqm in floor etc, over & including 15 mm thick screed bed in CM (1:6) complete set & jointed in neat cement slurry and pointed in white or coloured cement to match the surface over cement screed bed complete all as specified. Make : Kajaria/Orient/Somany/Spartek/Bell

M&L for Non – skid ceramic tiles, coloured, 7 to 8 mm thick (square/ rectangular) area of each tile exc. 0.11 Sqm but n. exc. 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified.

M&L for Non – skid ceramic tiles, coloured, 7 to 8 mm thick (square/ rectangular) area of each tile exc. 0.18 Sqm but n. exc. 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified.

Material & Labour 5 mm thick cement plaster on fair faces of concrete surface finished even & smooth without using extra cement in cement mortar 1:3 on ceiling/Chajjas/roof projection etc all as specified and directed by Engineer-in-Charge

Material & Labour 10mm thick rendering in CM 1:6 on fair face of brick work or concrete surface finished fair and even without using extra cement complete all as specified and as directed by Engr-in-Charge.

Material & Labour 15mm thick rendering in CM 1:4 on fair face of brick work, PCC solid block masonary or concrete surface finished fair and even without using extra cement complete all as specified and as directed by Engr-in-Charge.

M&L for Cement base paint two coats on undecorated, new plastered or unplastered surfaces of walls, including preparing new surface complete all as specified.

M&L fpr preparation of new wall surface, and applying three coat of White wash complete all as specififed and dircted by Engr-in-Charge.

Material & Labour for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of old plastered or unplastered surface of walls and applying two coat of white wash on wall complete all as specified and directed.

M&L for washing, rubbing down old distempered surfaces and applying two coat of oil bound distemper on wall complete all as directed.

S&F 4 mm Sheet glass, ordinary quality and glazing with oil putty or beading in square exc 0.5 sq. m in each pane complete all as specified.

M&L Preparation of old painted steel surfaces of any discription not other wise described over 10 cm width and girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Taking up or down steel water tubing and connections including cleaning for refixing or removing to store 15 mm dia .

S&F 15 mm bore, steel water tubing, medium grade, galvanized, with all fitting and fixed complete to walls and ceiling or laid into floor complete all as specified.

S&F 20 mm bore, steel water tubing, medium grade, galvanized, with all fitting and fixed complete to walls and ceiling or laid into floor in repairs complete all as specified.

S&F 500 Ltrs capacity, rotational moulded double layered polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part – I complete all as specified.

Supply & Fix bib taps cast copper alloy C P with crutch or butterfly handle screwed down, screwes for iron pipe for brass ferrule and fixed to 15mm bore complete all as specified and as directed by Engr-in-Charge.

S& F 15mm bore bib tabs cast copper alloy CP with crutch or butterfly handle screwed down (fixed in repair) complete all as specified and directed.

S&F15mm bore pillar tap copper alloy with capstan heads chormium plated screwed down high pressure screwed down and fly nuts complete all as specified and directed.

S&F Pillar tap, cast copper alloy, fancy type, with capstan head, chromium plated, screwed down high pressure, with or without lettered 'Hot or ‘Cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed to 15 mm bore steel tube complete all as specified.

S&F in repair Pillar tap, cast copper alloy, fancy type, with capstan head, chromium plated, screwed down high pressure, with or without lettered 'Hot or ‘Cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed to 15 mm bore steel tube complete all as specified.

Supply & Fix Angle valve cast copper alloy screwed down high pressured with crutch or butter fly handle screwed both ended for iron pipe and fixed 15mm bore complete all as specified and as directed by Engr-in-Charge.

S & F stop cock 15mm dia cast copper alloy weight not less than 400 grams with scored down high pressure with long shank and screwed both ends, complete all as specified and directed.

Supply & Fix Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed to 15 mm bore GI Pipe complette all as specified and as directed by Engr-in-Charge.

Supply & Fix Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed to 20 mm bore GI Pipe complette all as specified and as directed by Engr-in-Charge.

Supply & Fix 20 mm ball valves high pressure of PTMT with epoxy coated Aluminium rof and high density plastic ball screwed for iron pipe and fixed. (Minimum wt 210 gms) complete all as specified and as directed by Engr-in-Charge.

S&F PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified.

S&F in repair PVC waste pipe 32mm dia, 60 CM long for WHB, complete all as specified and directed.

S&F 110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.

S&F 75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.

S&F 75 mm bore, PVC (SWR) bends any radius complete all as specified.

S & F 75 mm bore, PVC (SWR) vent cowl complete all as specified and directed.

S&F 75 mm outer dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement to waste pipe & fixed in cement concrete (1:2:4) type B1complete all as specified.

S&F in repairs grating doom 125mm dia with waste hole of PTMT (minimum weight 40 gms) etc., complete all as specified and directed.

M & L for concrete bed to 150 mm dia drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete (1:4:8) type D - 2 using 40mm graded stone aggregate including necessary shuttering and supports to concrete and for laying beds to falls complete all as specified and directed.

Supplying, laying and testing of 150 mm bore SGSW (salt glazed stone ware) drain pipe grade 'A' laid in trenches to level/gradient, jointed all as specified and as directed.

Supply & Fix Vitreous squatting pan, `Orissa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) and making system fully functional and leak proof to the entire satisfaction of Engineer-in-Charge. Make Hindware/cera.

Supply & Fix vitreous china wash hand basin white flat back of size 550x400mm including brackets and CP waste coupling and making good to disturbed portion including PVC connection and PVC waste pipe etc complete all as specified and directed.

Supply & Fix in repair vitreous china wash hand basin white flat back of size 580x450mm including brackets and CP waste coupling and making good to disturbed portion excluding taps, waste pipe chain and plug and porcelain complete all as specified and directed.

S & F 125mm dia shower rose, swivel brass CP complete all as specified and directed.

S&F Low density polyethylene (LDPE) pipes, 32 mm bore, of pressure rating 6 Kgf/ Sqcm as in waste pipe complete all as specified.

S&F 10 Ltrs PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including 32mm dia flush pipe, brackets and connections to pipes and fixing of chain and pull, or lever, if any complete all as specified.

Supply & Fix Soap dish of size 160 x 90 mm any type fixed to plugs with chromium plated brass screw complete all as specified and as directed .

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed .

Taking down care fully MCB's unscrewing from wall and removing materials for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed .

Taking down care fully DB's unscrewing from wall and removing materials to for taking credit and making good to disturbed surfaces of walls, floors, etc complete all as specified and as directed .

M&L for point wiring for one light fitting / one fan point controled by one switch with 1.5 Sq mm PVC insulated unsheathed 1100 volt grade (FRLSH) copper conductor cable drawing in and including PVC Casing/capping with 1.5 Sq mm PVC insulated (FRLSH) copper conductor cable for continuous earth wire connected to main earth wire connected to each point and sunk cast pressed steel terminal box made out of MS sheet 1.25mm thick for mounting of fittings like switch, socket and fan regulator with 3mm thick laminated/bakalite sheet cover all complete all as specified and directed.

All as per srl item 107 above but for one 5 pin 5 amps socket outlet on the independent board.

All as per item No 107 above but for one 3 pin 5 amps socket outlet on the same board with other switchs.

All as per item No 107 above but with 2.5 Sq mm cable for Independent board one 3 pin 15 Amps socket outlet including S/C 1.5 Sq mm PVC insulated copper conductor unsheathed 1100 v grade IS -694 FR LS cable for continuous earth wire connected to gang box of required size.

S&F switch piano flush type single pole one way 5/6 Amps Complete all as specified and directed .

S&F socket outlet 5 pin 5/6 Amps flush type multipurpose suitable for 3 pin/2 pin plug Complete all as specified and directed .

S&F of switch piano15 Amp 230 Volt, flush button single pole one way Complete all as specified and directed .

S&F socket outlet 2 in 1, 3 pin 15/16 Amps flush type Complete all as specified and directed .

S&F ceiling rose surface type 3 terminals to be fixed on PVC block Complete all as specified and directed .

Supply and connecting electric step type fan regulator 5 step 300 watt suitable for 240 volt Complete all as specified and directed .

M&L for lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings/angle fittings Complete all as specified and directed .

Supply and fixing LED Lamp 12 W system lumen (NOM) 600 with all accessories all as specified and directed by Engg-in-Charge. Make:CG cat part No-LSW-12W-CDL-BC or equivelant as approved.

Supply and fixing bulk head fitting LED 10 watt fitting, 230 Volts ,etc complete with all accessories , connecting up with twin core twisted flexible copper conductor cable and testing complete all as specified and directed.: Cat Part no: LBHP-10-CDL of Make Cromption or equivelant as approved.

Supply and fixing surface & wall mounted LED batten 2feet with extruded housing and robust construction 10 W system lumen (NOM) 2000 with all accessories all as specified and directed by Engg-in-Charge. Make: Philips catalogue no. BN021 LED10S-6500 PSU GRS1 or equivalant of Wipro and CG

Supply and fixing in replacement surface & wall mounted LED batten 4feet with extruded aluminium housing and robust construction 20 W system lumen (NOM) 2000 with all accessories all as specified and directed by Engg-in-Charge. Make: Polycab catalogue no. LDO0103031 or equivalant of Wipro and CG

Supply and fixing in replacement of LED 2'x2' energy efficient recess mounting LED lumanaries not less then 40 watt, 100 lum/watt, 230 Volts, etc complete fixing accessories , connecting up with twin core twisted flexible copper conductor cable from ceiling rose to fitting, and testing complete all as specified and directed.

Supply and Fixing PVC Body sound proof Exhuast fan 150 mm size with single phase 230 Volt 900 RPM with louvers complete.making a hole in wall and after finishing work distrubed surface of wall complete all as specified and directed by Engr-in - Charge Make- Usha /Baja/CG

S & F ceiling fan 1200 mm sweep 5 star rating 230 V single phase with all accessories including provision of MS hooks suitable for hanging ceiling fans and connecting upto ceiling rose 1.5 Sqmm flexible copper wire complete all as specified and directed.

S&F sheet metal enclosure for DB, SPN with 200 amps rated bus bar , 240 Volt, 4 way, double door complete all as specified and directed. . Make- Havells/Standard/ Legrand

S&F sheet metal enclosure for DB, SPN with 200 amps rated bus bar , 240 Volt, 8 way, double door . Make- Havells/Standard/ Legrand

Supply and fixing MCB SPN 40 Amps 10 KA , 'B' Series, 240 volts including making connection complete all as specified Make- Havells/Standard/ Legrand

Supply and fixing MCB SP 6-32 Amps 10 KA, 'B' Series, 240 volts including making connection complete all as specified Make- Havells/Standard/ Legrand

S&F 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart incl 4 mm suspension wire, one twin core cable flat of size 10 Sqmm. (Make - Havells/Plaza/Fenolex)

Net Contract Sum will be after deducting Sch Of Credit of Rs. 5231.00

A P ENTERPRISES

M/S J.S.ENTERPRISES

NIRMAL SINGH BHOGAL AND SON

m/s jupiter builders