Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
₹2.7 Cr
EMD Value
₹2.7 L
Closing Date
3 Oct 2023, 11:00 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
NBCC Bhawan
NBCC Bhawan
Detailed Engineering, Supply, Installation, Testing and Commissioning of Permanent Mechanical works for 1 nos. of 150 meter high Reinforced concrete single steel flue chimney Unit 1 of FGD system at 3 660 MW North Karanpura STPP, Jharkhand
NBCC/SBG/RAN/2023/76~EWa20d9fbf31623313444e7aeb
NBCC/SBG/RAN/2023/76
Open Tender-Domestic
Civil Works General
NBCC Bhawan
₹11,800
₹2.7 L
3 Oct 2023
9 Sept 2023
3 Oct 2023
9 Sept 2023
3 Oct 2023
NO. 1) Quantity (Rs.)
Supplying high strength structural bolts (of property class 8.8
and product grade `C' as per IS: 1367) and conforming to IS: 3757 and
high strength structural hardened and tempered nuts (of property class
`8' as per IS:1367) conforming to IS:6623 with hardened and
S25 tempered washers as per IS:6649 etc. up to and inclusive of 39 mm Quintal 50.00 50.00 0.00
diameter and upto 300 mm long for structural steel work etc all
complete. (Final measurement of total qty of this item shall be shall be
restricted to total quantity of Item no. 25 of SCHEDULE-3 admitted in
final bill).
Supplying C276 strips, plates, gutters / vanes / pipes, bends, fittings
and any other appurtenances as required in chimney for
collection and withdrawal of condensate from inside of flue liner to
outside based on the approved design in line with gas-flow-model study
report all complete as per specification, drawing and as directed
by the Engineer-in-charge. Final measurement for payment shall be
done for net weight of C276 strip only after erection (weld
thickness not to be considered). (Final measurement of total qty
of this item shall be shall be restricted to total quantity of Item no. 26F
of SCHEDULE-3 admitted in final bill).
Total A Rs0.00
BOQ (Service Part)
ITEM SL Quantity (Unit Total Rate Amount
Description of Item Unit
NO. 1) Quantity (Rs.) (Rs.)
PART 1A Civil Works
Supplying, fabrication, erection and alignment of factory made
chequered Plate with mild steel conforming to IS:2062 in
platforms, staircases with edge binding strips and anti-skid nosing
in treads etc. including 2 coats of redoxide zinc-chromate primer
(one coat at shop and one coat after erection), fixing clamps,
fittings, fixtures, all taxes, duties, packing, grinding, drilling,
welding, edge preparation, etc. all complete. [Structural steel &
chequered plate shall be issued by BHEL free of cost]
Fixing in positing of high strength structural bolts (Material as per
25 Sl No. S25 of SCH-4 SUPPLY) for structural steel work at all level Quintal 50.00 50.00 0.00
etc. complete.
Fabricating and erecting C276 strips, plates, gutters / vanes / pipes,
bends, fittings and any other appurtenances as required (Material
as per Sl No. S26F of SCH-4 SUPPLY) at all elevation in
chimney for collection and withdrawal of condensate from inside of flue
liner to outside based on the approved design in line with gas-
26F flow-model study report, sealing, testing including surface Kg 1800.00 1800.00 0.00
preparation, TIG or any other type of specialised welding for C276
Strips etc all complete as per specification, drawing and as
directed by the Engineer-in- charge. Measurement for payment
shall be done for net weight of C276 strip only (weld thickness
not to be considered).
Providing, fabricating and installing at various locations and
elevations of the chimney system the following miscellaneous
mild steel items complete with the cost of all labour, material and
27 equipment, transporting, lifting, setting in place, cutting,
grinding, drilling, welding, bolts and bolting, anchor fasteners
and anchoring, priming, painting, grouting etc. complete as per
drawings and specifications:
Mild steel ladders with cage, hood access hatch, louvers, bird
a screens, hood drain basin covers and other miscellaneous mild steel MT 9.00 9.00 0.00
items not specifically mentioned.
32 / 40 mm nominal bore medium class tubular hand railing
for stair case and internal and external platforms.
Providing minimum 275 gsm Hot dipped galvanisation on
mild steel parts as per specification.
Digitally signed by PRIYA
KUMARI
Date: 2023.09.21 16:24:17 IST
Providing minimum 610 gsm Hot dipped galvanisation on
mild steel parts as per specification.
Supplying, fabricating and installing gas sampling and gas
oapacity measurement ports made of C276 pipe in chimney
liners, including bolts, non metallic gaskets, cover plates and
any other accessories as required, painting etc, all
complete as per specification, drawing and as directed by the
engineer-in-charge.
Fabricating and erecting above roof level 2mm thick titanium
sheet (Material as per Sl S30AA of SCH-4 SUPPLY) wrapped
over chimney mini-shell (as described in item no. 30AAA and
insulation over it) external surface, including weldables/consumables,
equipment, material, acid resistant nuts, bolts, washers, screws and
any other accessories as required for proper fixing, surface finishing,
testing, preparation of detailed fabrication drawings etc all complete
per specification, drawing and as directed by the Engineer-in-charge.
Preparing detailed fabrication drawings and after approval by the
Engineer, providing, fabricating and installing at all levels, stainless
plates (including stainless steel screws and fasteners) of grade AISI
316L and lead sheets over the mild steel in the platform beam
bearing, flue supports bearings, flue restraints brackets / buffers etc.
including the cost of all labour material & equipment, transporting,
lifting to all heights, setting in place, cutting, grinding, drilling,
welding of stainless steel using compatible & approved stainless
steel electrodes, testing & machining flat and polishing the
contact surfaces of stainless steel, coating the polished surfaces
with silicone grease, etc., complete as per drawings and
specifications.
a Stainless steel components. KG 120.00 120.00 0.00
b Lead Sheets. KG 40.00 40.00 0.00
Preparing detailed fabrication drawings and after approval by the
Engineer and as per actual site condition to withstand the wet flue
gas, providing, fabricating and installing expansion compensator
joints including bolster in the flue liner including all labour,
32 material and equipment transporting, hoisting, fixing in position, Sqm 40.00 40.00 0.00
drilling, cutting, bolts and bolting, etc. along with the user
handbooks (giving details of installation, dismantling and
maintainance procedures for the expansion joints), testing, approval
form BHEL/NTPC etc complete as per drawings and specifications.
Supplying, and placing in position (at the beam supports
bearings) Neoperne pads between concrete surface and mild
steel including the cost of all labour materials, cutting to shape,
grinding, drilling etc., complete as per drawings and specifications.
Providing, laying and packing, at all levels, asbestos ropes at
43 expansion joints including the cost of all labour material, etc. complete
as per drawing and specifications.
b 12 mm (diameter) at expansion joints between linig segments. Rm 320.00 320.00 0.00
Providing and installing, at all levels,
resin bonded rock wool insulation slabs of density not less than
100 kg/cu.m with an installed thickness of not less than 100 mm,
on the outside surface of steel flue liners,on the outside surface
of brick liner, on the inside surface of concrete windshield, inside
surface of concrete minishells, under the cast iron caps and
wherever as directed by the Engineer, in two layers (each 50 mm
thick) including the cost of all labour, material and equipment,
transporting, lifting to all heights, etc., inclusive of plated or galvanised
accessories such as pins/studs/anchors/wire netting, speed
washers, tying wires, etc. welding of pins/studs to steel surfaces
or embedding of pins/studs/anchors in concrete surfaces, fixing,
cutting, cutting, lapping, binding, testing, etc. complete as per
drawings and specifications.
Providing and packing, at all levels, loose rock wool insulation to a
density not less than 100 kg/cu.m between the insulated minishells
and brick liners at expanjoints between the lining segments and
wherever as directed by the Engneer including the cost of all
labour, material and equipment, filling, ramming, testing, etc.
complete as per drawings and specifications.
Digitally signed by PRIYA
KUMARI
Date: 2023.09.21 16:24:17 IST
Designing, supplying, fabricating and installing after approval
by the Engineer, non- metalic expansion joints to seal gaps
between chimney components and to meet the service
requirements of wet stack and as given in the specifications
alongwith the cost of all components of the expansion joint,
69 insulation, galvanised bolts, nuts, washers, anchor fasteners and
retaining bars, packing materials and reinforcements at the
connecting ends and flanges, lapping etc. including cost of all labour
and equipment, user hand books (giving details of installation,
dismantling and maintenance procedures for the expansion joints) etc.
complete as per drawings and specifications for:
a Expansion joint between ducts and liners. Sqm 50.00 50.00 0.00
b Expansion joint between duct and chimney shell. Sqm 50.00 50.00 0.00
Fabricating and erecting FRP Pipes (Material as per Sl No. S73 of SCH-4
SUPPLY) with all bends, flanges, stiffeners, all other flue
attachments, including support system, collars, connection with
C276 pipes and any other accessories as required outside chimney flue
73 liner at all elevation based on the approved design in line with Kg 488.00 488.00 0.00
gas-flow-model study report, including surface finishing, sealing,
lamination, moulding, testing, guarantee / warranty etc. complete
as per drawings, specification, manufacturer's recommendations
and relevant codes.
Erection and Alignment of miscellaneous steel parts to be embedded/cas t
in concrete (like staircase embedments, corbel face plates, etc) at all
positions and levels including the cost of all labour, materials and equipments
22 for setting materials in concrete, grouting, welding, bolts & bolting, expansion MT 3.00 3.00 0.00
anchors, drilling, cutting, etc. complete as per drawings and
specification.[Material supply including structural steel parts is in scope of
contractor] (FABRICATION AND ERECTION)
Erection and Alignment of high strength structural steel (E350 ) in built up section
conforming to IS:2062, in columns, beams, struts, monorails, stays, safety
chains, ladders, gantry girders, roof trusses, portals, laced purlins, space
frames, hangers, wall beams, sheeting runners, brackets, stiffeners, stub
columns, bracings, cleats, base plates, splice plates,gussets, end plates, steel
frame grid over false ceiling, walkway platforms, ladders, stairs,stringers,
treads, landings, decking and seal plates, galleries etc including blast
cleaning, providing & applying primer,providing and applying intermediate, final and
final finish coat of paint (blast cleaning,primer and paint shall be paid separately
as per item no C23, D23 & E23),connection design & preparation of
fabrication drgs, straightening, cutting, bending, rolling, grinding, machining,
drilling, welding, electrodes and other consumables, alignment, erection bolts &
nuts (weight of erection bolts, nuts and welds not payable), assembly, edge
preparation, preheating (However, permanent bolts are payable separately),
assembly, edge preparation, preheating (min preheat and interpass temperature of
120-140o C for welding over 20 mm thickness & use of low hydrogen/
radiogenic electrodes), post heating, testing of welders, inspection of welds, visual
inspection, non destructive and special testing, rectification and correction of
defective welding works, production test plate, inspection and testing,
erection scheme, protection against damage in transit, stability of structures,
installation of temporary structures, setting column bases, surface preparation by
means of manual or mechanical power tools as per IS:1477 part 1, touch-up
painting, rectification, dismantling and removal of all temporary structures
(weight of temporary structures not payable), etc all complete. Including
appointment of a seperate agency, approved by BHEL, for review and approval
of fabrication drgs, in consultation with BHEL.
For shop fabricated structural steel (Supply of structural steel in vendor scope)
a Payment terms on : (a) Supply of fabricated material - 65 % (b) Erection - 25% (c) MT 44.00 44.00 0.00
Alignment - 10% ONLY ERECTION
For site fabricated structural steel(Structural steel shall be issued by
b BHEL free of cost) Payment terms on : (a) Fabrication - 65 % (b) MT 11.00 11.00 0.00
Erection - 25% (c) Alignment - 10% FABRICATION AND ERECTION
Digitally signed by PRIYA
KUMARI
Date: 2023.09.21 16:24:17 IST
Erection and Alignment of structural steel of grade E 250 in rolled/ built up
section conforming to IS:2062, mild steel rounds in columns, beams, struts,
monorails, stays, safety chains, ladders, MS gratings, gantry girders, roof
trusses, portals, laced purlins, space frames, hangers, wall beams, sheeting
runners, brackets, stiffeners, stub columns, bracings, cleats, base plates, splice
plates,gussets, end plates, steel frame grid over false ceiling, walkway
platforms, ladders, stairs,stringers, treads, landings, decking and seal
plates, galleries etc including blast cleaning, providing & applying
primer,providing and applying intermediate, final and final finish coat of paint (blast
cleaning,primer and paint shall be paid separately as per item no C23, D23 & E23),
connection design & preparation of fabrication drgs, straightening, cutting, bending,
rolling, grinding, machining, drilling, welding, electrodes and other consumables,
alignment, erection bolts & nuts (weight of erection bolts and nuts not payable),
assembly, edge preparation, preheating / post heating if required, testing of
welders, inspection of welds, visual inspection, non destructive and
special testing, rectification and correction of defective welding works,
production test plate, inspection and testing, erection scheme, protection
against damage in transit, stability of structures, installation of temporary
structures, setting column bases, surface preparation by means of manual or
mechanical power tools as per IS:1477 part 1, touch-up painting, rectification,
dismantling and removal of all temporary structures (weight of temporary
structures not payable), etc all complete. Including appointment of a seperate
agency, approved by BHEL, for review and approval of fabrication drgs, in
consultation with BHEL.
For shop fabricated structural steel(Supply of structural steel in vendor scope)
a Payment terms on : (a) Supply of fabricated material - 65 % (b) Erection - 25% (c) MT 132.00 132.00 0.00
Alignment - 10% ONLY ERECTION
For site fabricated structural steel(Structural steel shall be issued by
b BHEL free of cost) Payment terms on : (a) Fabrication - 65 % (b) MT 33.00 33.00 0.00
Erection - 25% (c) Alignment - 10% FABRICATION AND ERECTION
Erection and Alignment at all levels, structural steel flues (liners) complete
with all bends, flanges, stiffeners, all other flue attachments, support system, collars,
access manholes and gas sampling ports alongwith gaskets and other
accessories, staying system, including the cost of all labour, material and
equipment, transporting, lifting to all heights, setting in place, cutting, grinding,
26 drillings, bending, bolts and bolting, welding, preheating and post-heating for MT 360.00 360.00 0.00
welding, testing, etc. complete as per drawings and specifications. [Structural steel
shall be issued by BHEL free of cost] . The Flue can to be transported inside the
concrete shell horizontally during erection activity . All necessary
arrangement for horizontal movement of flue liner shall be in the scope of
contractor .
Fabrication & Erection of Tilting Platform including cost of materials, the cost of
all labour, material and equipment, transporting, lifting to all heights, setting in place,
cutting, grinding, drillings, bending, bolts and bolting, welding, preheating and post-
heating for welding, testing, etc. complete as per drawings and specifications.
(Remarks Tilting Platform is required for Flue Can to be transported inside
the concrete shell horizontally during erection activity. All necessary
arrangement for horizontal movement of flue liner shall be in the scope of
contractor.)
Supply & application including blast cleaning of outer surface of Tilting
Platform to near white metal surface conforming to Sa 2 ½ finish of ISO 8501-1
with surface profile 40-60 Micron and providing and applying two component
moisture curing zinc (ethyl) silicate primer coat (having minimum 80% of
metallic Zinc content in dry film, solid by volume minimum 60%±2%) of
26-TP (a) minimum 70 micron DFT including the cost of all labour, material, MT 15.00 15.00 0.00
equipments, protection of surface and cleaning, scoffolding, touch-up painting
etc., complete as per drawings, specifications and instructions of the
Engineer. Zinc dust composition and properties shall be Type-II as
perASTM D520-00. Primer coat shall be applied in Shop immediately after
blast cleaning by airless spray technique.
Providing and applying on outer surface of Tilting Platform, Finish coat of
two-pack aliphatic Isocyanate cured acrylic finish paint (solid by volume
minimum 55% ±2%) with Gloss retention (SSPC Paint Spec No 36, ASTM D
4587, D 2244, D 523) of Level 2 (after minimum 1000 hours exposure, Gloss loss
less than 30 and colour change less than 2.0 ∆E) and minimum 70 micron
26-TP (b) DFT over steel sections already having intermediate coats, including the cost of all MT 15.00 15.00 0.00
labour, material, equipments, protection and cleaning, scoffolding etc. all complete
as per drawing and specifications. This coat shall be applied after an interval of
minimum 24 hours (from the application of sealer coat) and within six (6) months
(from the completion of Intermediate coat). Colour and shade of the coat shall be as
approved by the Employer.
Providing, fabricating and installing at various locations and elevations of the
chimney system the following miscellaneous mild steel items complete with the
cost of all labour, material and equipment, transporting, lifting, setting in
place, cutting, grinding, drilling, welding, bolts and bolting, anchor fasteners
and anchoring, priming, painting, grouting etc. complete as per drawings and
specifications:
Mild steel ladders with cage, hood access hatch, louvers, bird screens,
a hood drain basin covers and other miscellaneous mild steel items not specifically MT 9.00 9.00 0.00
mentioned.
32 / 40 mm nominal bore medium class tubular hand railing for stair
case and internal and external platforms.
Providing minimum 275 gsm Hot dipped galvanisation on mild steel
parts as per specification.
Providing minimum 610 gsm Hot dipped galvanisation on mild steel
parts as per specification.
Total B 0.00
Grand Total A + B 0.00
Grand Total A + B 0.00
Digitally signed by PRIYA
KUMARI
Date: 2023.09.21 16:24:17 IST
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.06 MB
1 NIT.pdf
Tender Document
2 SCC.pdf
Tender Document
4 GCC 2022 WITH AMENDMENT NO 06.pdf
Tender Document
5 APPROVED MAKES.pdf
Tender Document
7 TCC Drawings.pdf
Tender Document
9 Revised memorandum.pdf
Tender Document
Re rev Physical milestone.pdf
Tender Document
11 Annexure- VI.pdf
Tender Document
8 Revised BOQ.pdf
Tender Document
corrigendum-1947-Corri- 5 76.pdf
pdf • 0.12 MB
addendum-507d069b78b6-Corri 30076.pdf
pdf • 0.17 MB
corrigendum-1940-Corri-4 76.pdf
pdf • 0.10 MB
addendum-f48ab1b28a64-Corri-4 76.pdf
pdf • 0.10 MB
addendum-a1ed876b43c6-Corri 3076.pdf
pdf • 0.17 MB
addendum-73f0321658ca-Corri 3 76.pdf
pdf • 0.17 MB
corrigendum-1928-Corri 03 76.pdf
pdf • 0.17 MB
corrigendum-1922-Corri-2 76.pdf
pdf • 0.12 MB
corrigendum-1916-Corri-1 76.pdf
pdf • 0.12 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .