Maintenance of Vandithode Check Dam in Pulpally Panchayath, Chittoor, Palakkad District -Painting and erection of 9 nos of new MS Shutters with hoisting arrangements and other connected works

Amount

Providing RING BUND across the canal and DEWATERING using a 5HP pump

RING BUND - putting up ring bund as per approved shape 6m bottom width and 3 m top width using empty gunny bar polythene bag filled with earth placed in two rows at 1m apart and filled in between with puddle clay to form bund for an average height 3.5m and total length of 1 m includinglabour dismantling the bund after completion of the work.Vol. of bund (6+3)/2*3.5*1=15.75m3Vol of core 1*3.5*1 = 3.5m3vol of earth 15.75-3.5= 12.25m3No. of bags 12.25/0.027 =454nos

Bailing out water Using 5HP Pump- Bailing out water with 5HP engine and pump set including conveyance to site and erection,cost of fuel, lubrication oil and other stores, pay of staff etc complete

DISMANTLING the old wooden plank shutter. DEMOLISHING for C-groove and sill beam fixing. CHIPPING the existing concrete pier top.

LIFTING, LEADING and STACKING the existing wooden plank at convenient place.

Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In cement mortar

Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

FORM WORK, PCC, RCC & PLASTERING for Sill Beam, C Groove, Pier & Slab

Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand.

Providing and laying in position specified grade of Reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size. (Assessment of compressive strength of concrete by cube testing in Govt. Lab)

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more. Make: Vyzak, SAIL, TISCO, JSW or eq. steel of primary make.

12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

Supply, Fabrication, Erection & Painting of EMBEDDED PARTS

Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

Supply of MS round bar including cost of conveyance charges

Fabrication, erection and commissioning of STRUCTURAL MILD STEEL EMBEDDED PARTS for CANAL GATES

Fabrication, supply and erection in correct position and alignment SS 304L grade plate for CANAL GATE

Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

Supply, fabrication, painting and erection of MS SHUTTER

Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

Fabrication and supply of STRUCTURAL STEEL CANAL GATE and its accessories

Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

ERECTION of the CANAL GATE safely in the grooves

Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing

Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings

Providing SCREW ROD and WORM & PINION

SUPPLY & STACKING of WORM & PINION

Providing EN-8 SQUARE THREADED SCREW ROD of dia 63mm (per kg rate)

THREAD LESS portion of the screw rod (per kg rate)

SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE

Supply, fabrication, painting and erection HOISTING BRIDGE, WALKWAY PLATFORM and HAND RAIL

Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges.Make: TATA, VIZAG, SAIL,JSW or eq.

Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges. Make: TATA, VIZAG, SAIL,JSW or eq.

Supply of MS checquered plates including cost of conveyance charges. Make: TATA, VIZAG, SAIL,JSW or eq.

Supply of MS round bar including cost of conveyance charges. Make: TATA, VIZAG, SAIL,JSW or eq.

SUPPLYING & STACKING of Dia 32 mm G.I. PIPE. Make: TATA, JSW,Apollo or eq.

Supply of BOLT and NUT up to 300mm Length including cost of conveyance. Make with IS.

SUPPLYING & FIXING of BUTT HINGE. Make with IS.

SUPPLYING & FIXING of TOWER BOLT. Make with IS.

SUPPLYING and STACKING of PAD LOCK. Make with IS.

Fabrication and supply of HOISTING UNIT for CANAL GATE in structural steel

Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site. Make: Asian, Berger, Nerolac or eq. in the order of pref.

ERECTION of the HOISTING UNIT and its ACCESSORIES

Note :1 All materials, Items, Equipment shall be best branded items with IS and approved by client/KEL

2:Rate should be inclusive of installation, testing and commissioning cost for all items

3.Rate should be Exclusive of GST.

4.Work should be executed as per DSR/PWD/Irrigation Dept. specification and direction of Engineer at site.

SIMI ANZAR