Construction of Animal Husbandry Epicentre at Mandava, Ta: Ankelshwar, Dist: Bharuch

No figures

1 Excavation for foundation upto 1.5 m depth including 409.70 Cumt 149.67

sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(B)

Dense or Hard soil

2 Excavation for foundation for depth from 1.5 m to 3.0 m 225.70 Cumt 162.38

including sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(B)

Dense or Hard soil

3 Filling in foundation and plinth with sand in layers of 20 19.00 Cumt 460.19

cm. Thickness including watering ramming and

consolidating etc. comp.

4 Filling available excavated Earth (Excluding Rock) in 121.60 Cumt 130.39

trench plinth side of foundation . in layer not excluding

20 cm in depth consolidation each deposited layer by

ramming and watering etc. complete

soil in layer of 20 cm in thickness including ramming

watering and consolidating etc. complete

Item Rate In

Description of Item Quantity Unit Amount

No figures

6 Anti Termite System 81.90 Sqmt 134.33

P/L of Permenent piping technology Anti Termite

treatment before flooring work by installing LLDP (Low

linear density Polyethylene) tube of 8 mm O.D.& 6.4 mm

I.D.With in Built Pressure Compenstaion chif every 30 cm

interval in the tube, having working pressure of 2 kg/cm

2 and realese rate of 1.9 ltr/Hour fixed by P-Clip and

nails . The LLDP pipe shall be installed at the entire

periphery of the building and at internal network of

building depth of 20 to 200 mm under floor every 2 to

mtr.c/c distance (adjustble as per building layout ) &

Ends of loop pass through a PVC Elbow of minmum

mm ID at junction box of wall and floor level, entring into

a steel reinforcmed grooved flexible pipe mini.22 mm LD

leading into junction box and during injecting chemicls

for termite control tretment. The anti-termite chemical

Lmidcloprid 30.5% SC Mix as per IS 6313(part-III) shall

be injected by the pressure pump diluted with water @

10.5 ml/5ltr of water at the rate of 2 kg/sq,cm.@ 5 ltr

/Smt .the contractor shall submit approved line plan for

piping system and junction boxes dully approved By

Engineer -in-charge with bond of 5 Years warnty .

7 Providing and laying cement concrete 1:3:6 (1-Cement : 5.70 Cumt 2965.76

3- coarse sand : 6- machine cut stone aggregates 40 mm

nominal size) and curing complete excluding cost of

formwork in (A) Foundation and Plinth

8 Providing and laying controlled cement concrete M150 65.19 Cumt 4074.34

for curing complete including cost of formwork but

excluding the cost of reinforcement for reinforced

concrete work in PCC

9 Providing and laying controlled cement concrete M250 64.30 Cumt 4327.85

and curing complete including the cost of formwork and

excluding reinforcement for reinforced concrete work for

Foundations, Footings , Mass concrete , for Footing

10 Providing and laying controlled cement concrete M250 3.30 Cumt 6961.93

and curing complete including the cost of formwork and

excluding reinforcement for reinforced concrete work for

,Column Upto GL

11 Providing and laying controlled cement concrete M250 21.70 Cumt 5875.17

and curing complete including the cost of formwork and

excluding reinforcement for reinforced concrete work for

,Plinth Beam/Ground Beam

Item Rate In

Description of Item Quantity Unit Amount

No figures

12 Providing and laying controlled cement concrete M200 14.40 Cumt 5285.94

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced

concrete work in Plinth Slab,

13 Providing and laying controlled cement concrete M200 0.90 Cumt 6994.26

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced

concrete work in Column Upto PL

14 Providing and laying controlled cement concrete M-200 16.80 Cumt 6889.06

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced

concrete work in Columns, pillars posts and struts For GF

15 Providing and laying controlled cement concrete M-200 2.60 Cumt 6889.06

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced

concrete work in Columns, pillars posts and struts For FF

16 Providing and laying controlled cement concrete M.200 8.70 Cumt 5811.54

and curing complete including the cost of formwork and

excluding reinforcement for reinforced concrete work in

(C) Ground floor Beams,

17 Providing and laying controlled cement concrete M-200 0.30 Cumt 6107.57

and curing etc. complete including the cost of form work

and reinforcement for reinforced concrete work in (c)

Chhajja for Ground floor

18 Providing and laying controlled cement concrete M-200 0.70 Cumt 7078.59

and curing etc. complete including the cost of form work

and reinforcement for reinforced concrete work in (c)

Lintal for Ground floor

19 Providing and laying controlled cement concrete M.200 9.60 Cumt 6550.86

and curing complete including the cost of formwork and

excluding reinforcement for reinforced concrete work in

(C) Ground floor Slab

20 Providing and laying controlled cement concrete M-200 3.20 Cumt 6008.31

for RCC work and curing complete including the cost of

form work but excluding the cost of reinforced concrete

work in coping on Ground Floor

21 Providing and laying controlled cement concrete M-200 1.00 Cumt 6008.31

for RCC work and curing complete including the cost of

form work but excluding the cost of reinforced concrete

work in coping on F Floor

22 Providing IS Mark TMT FE-500D bar reinforcement for 16485.00 Kg 76.26

RCC work including bending & placing in position

complete up to All floor Level

Item Rate In

Description of Item Quantity Unit Amount

No figures

23 Brick work using common burnt clay building bricks 19.00 Cumt 4021.02

having crushing strength not less than 35 kg./Sq.Cm. in

foundation and plinth in Cement Mortar 1:5. (1- Cement :

5 -fine sand) (B) Conventional below plinth

24 Brick work using common burnt clay building bricks 60.30 Cumt 4289.33

having crushing strength not less than 35 kg./Sq.Cm. in

foundation and plinth in Cement Mortar 1:5. (1- Cement :

5 -fine sand) (B) Conventional For GF

25 Half Brick masonry in common brunt clay building bricks 26.80 Sq m 651.67

having crushing strength not less than 35 Kg/Sq.Cm. in

Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in

foundation and plinth (B) Conventional in super

structure. for GF

26 Half Brick masonry in common brunt clay building bricks 48.60 Sq m 651.67

having crushing strength not less than 35 Kg/Sq.Cm. in

Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in

foundation and plinth (B) Conventional in super

structure. for FF

27 Providing and fixing 150 mm wide, approved quality 53.10 Sqmt 295.93

chicken wire mesh at junction of brick work and RCC

work or two dissimilar surfaces, at all heights fixed by

nails, rowal plugs or tag before applying the plaster,

including curing, scaffolding all complete as directed.

28 Providing 15mm thick cement plaster in single coat on 303.50 Sqmt 173.09

Rough (Similar)side of single or half brick walls for

interior plastering upto floor two level and finished even

and smooth in (ii) Cement mortar 1:4 (1-cement :4-

sand). For G Floor

29 Providing 15mm thick cement plaster in single coat on 53.40 Sqmt 173.09

Rough (Similar)side of single or half brick walls for

interior plastering upto floor two level and finished even

and smooth in (ii) Cement mortar 1:4 (1-cement :4-

sand). For F Floor

30 Providing 10 mm. Thick cement plaster in single coat for 65.00 Sqmt 150.80

plastering on ceiling and soffits of stairs and finished

even and smooth in : (I) Cement mortar 1:4 (1 cement :

sand) smooth finish etc. complete. G Floor

Item Rate In

Description of Item Quantity Unit Amount

No figures

31 20 mm thick Sand faced cement plaster with 1cmx1cm 539.80 Sqmt 351.48

grooves as suggested by this office consisting of 12 mm

thick backing coat of C.M. 1:3 ( 1 cement : 3 coarse sand )

and 8 mm thick finishing coat of C.M. 1:1 ( 1 cement :

coarse sand) for all heights as directed etc. complete.

and as per pattern sample aprroved by the architect or

directed engineer in-charge

32 Providing throating or plaster drip and moulding to 3.90 Rmt 41.00

R.C.C. Chhajja.

33 Applying two coats of Acrylic lapy (putty) & two coats of 353.90 Sqmt 40.59

primer of approved brand and manufacture on new wall

surface to give an even shade including thoroughly

brushing the surface free from mortar dropping and

other foreign matter and sand papered smooth.

34 Wall painting (two coats) with plastic emulsion paint of 288.90 Sqmt 78.90

approved brand and manufacture on undecorated wall

surface to give an even shade including throughly

brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth.

35 Painting (two coats) with plastic emulsion paint of 65.00 Sqmt 84.16

approved brand and manufacture on undecorated ceiling

surface to give an even shade including throughly

brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth.

36 Wall Painting (Two coats) with weather proof acraylic 539.80 Sqmt 114.53

emulsion paint of approved brand and manufacture and

of required shade on exterior wall surface to give an even

shade over and including primery coat with Alkaly

resistance primer of approved brand after thoroughly

brushing surface to remove all dust and remains of

loose powdered material etc. copm. for all height

37 Providing and laying broken chine mosaic flooring for 61.00 Sqmt 747.29

terrace using 12 mm to 20 mm broken pieces of glazed

tiles to be laid over cement mortar 1:3 to plain or slope

and to be tempered to bring mortar creme out upto

surface using white cement including rounding off

junctions and extending them upto 15 cm along the

wall,clearing with water and oxalic acid etc. as directed.

Item Rate In

Description of Item Quantity Unit Amount

No figures

38 Providing and laying cement concrete flooring 1:2:4 (1- 61.00 Sqmt 330.88

cement : 2- coarse sand : 4-graded stone aggregate

20mm nominal size) laid in one layer and finished with a

floating coat of neat cement. (B) 50mm thick

39 Providing Plinth Protection to Building including 50.20 Sqmt 2227.05

excavation in ordinary soil and laying cement concrete

1:3:6 using stone aggregates of 40mm nominal size in

foundation layer 125 mm thick+ 125mm thick sand layer

below pre-cast Rubber Dye inter locking concrete block

60mm thick with grade of concrete M300 pneumatic

compressed by mechanically pressed and as per

approved design including 75mm Sand layer for

levelling and filling the joint with sand in proper line and

level etc. complete, Including Providing and fixing pre-

cast concrete kerb stone of grey cement based concrete

block 30cm length, 30cm height and 15cm thick made of

M250 grade concrete as per approved design and

including excavation for fixing in proper line and level,

filling the joint with C:M 1:3 (1cement:3 fine sand) etc.

40 Providing and fixing Approved Brand (30mm) Three 5.80 Sqmt 3363.60

track alluminium window standerd extruded colour

anodized aliminium section with Frame having frame

bottom member @ wt. Of 1.223 Kg/Rmt , frame Side and

top member @ wt. Of 1.685 Kg/Rmt with sliding

shutters of single glass shutter top bottom member @ wt.

Of 0.839 Kg/Rmt & side member @ wt.of 0.731 Kg/Rmt

& Inter lock member @ wt.of 0.731 Kg/Rmt with 5 mm

thick transparent plain float glass in shutter including

fitting, fixtures, rubber gasket and transparent silicon

sealant as per drawing and instruction of Engineer - in -

charge etc. completed for window three track

41 Providing & Fixing in position standard extruded 0.40 Sqmt 2722.95

approved colour anodised Aluminum Ventilation with

outer frame 65 x 25 x 1.50 mm Stander Box Frame @ Wt

0.833 kg/Rmt with 5mm thick fixed ground glass fixed to

alluminium strip blade fixed or adjestable ventilation &

including all required materials, fixtures, fastenning,

labours and equipments as per detailed drawing as

directed. For Ventilators

Item Rate In

Description of Item Quantity Unit Amount

No figures

42 Providing and fixing 35mm thick flush double door 3.00 Sqmt 4682.36

shutter with 100x50mm wooden frame , solid core for

durable grip of hinges & Double shutter with required

75x35mm wooden batten having 1mm thick pattern

lamination on both side, Durable Grip shall be providing

with both side 60cm long stainless steel handle , 2 tower

bolts and aldrops including necessary Locking system

S.S. fixtures & fastenings etc. directed by engineer in

43 Providing and fixing 35mm thick flush single door 4.20 Sqmt 3881.43

shutter , solid core for durable grip of hinges & single

shutter with required 75x35mm wooden batten having

1mm thick pattern lamination on both side, Durable Grip

shall be providing with both side 60cm long stainless

steel handle , 2 tower bolts and aldrops including

necessary Locking system , S.S. fixtures & fastenings etc.

directed by engineer in charge.

44 Providing and fixing FRP frame size 100 x 50 mm and 35 1.90 Sqmt 2363.40

mm thick ( Fiber Glass with PUF Injection ) FRP depress

panel Single or Double shutter having extra

reinforcement on sides & edges in Gel coat finish.The

core of the both shutter & frame is to be filed up with

injected fire retradat grade polyurethene foam done in

situ along with embeded wooden pieces for stiffening &

also taking hinges & fintures.The whole FRP frame &

single or double shutter is to be waterproof,

weatherproof, termite proof & resistance to mild

acid/alkali. Rates are to be inclusive of S.S hinges with

necessary screws & S.S fixtures & fastenings & fartener

sleeve.Colour and Shade approved by Engineer-In-

45 Providing & Laying 24" x 24" GVT vitrified 8 mm thick 52.50 Sqmt 1592.77

tile flooring over 20 mm (average) base of cement

mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or

fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color

cement slurry including finised with flush pointing &

cleaning the surface etc. complete shade approved by

directed engineer in-charge.

46 P & L 60x60 cm' GVT vitrified 8 mm thick tile risers of 5.00 Sqmt 1233.21

steps,skirting Dedo of cement mortar 1:3 (1cement :

coarse sand)and jointed with by adhesive materials

including colour cement slurry including finished with

flush pointing & cleaning the surface etc. complete for

including colour approved by directed.

Item Rate In

Description of Item Quantity Unit Amount

No figures

47 Providing and laying antiskid ceramic tiles 30 x 30 cm 2.50 Sqmt 957.63

size 6 mm thick in flooring treads of steps and landing

laid on a bed of 12 mm thick cement mortar 1:3(1-

cement:3-coarse sand)finishing with flush pointing in

white cement

48 Providing and laying primium printed glazed tiles tiles 24.60 Sqmt 1417.36

size 30 x 60 cm 8 mm thick in skirting risers of steps and

dedo on 10 mm thick cement plaster 1:3 (1-

cement:3coarse sand) and jointed with colour cement

slurry etc completed.

49 Providing and laying machine cut free edge machine 2.20 Sqmt 944.35

Green Marble Slab 18 to 20 mm finished treads and

risers in length with 1cm projecting nozing rounded

moulding in ttread laid over 20 mm (av.) thick of CM 1:6

on treads and 10mm thick CM 1:3 on risers jointed with

grey or colour cement slurry including rubbing and

polishing incl. making Three No.s of grooves of size 3mm

X 3mm along the length of treads etc. complete

50 Providing and fixing frosted finished 600mm x 1200mm 0.80 Sqmt 6008.49

glass urinal partition with crystalline Dhar polish on

exposed edges, supported by SS legs and fitting bracket

clamp with cut holes and silicon grouting, including all

accessories and labor charges directed by the

engineering in charge, etc. complete

51 Providing and fixing mirror polished 18 mm thick Green 25.50 Sqmt 2271.49

Marble stone with full round edge and polished of

approved quality in clading on sill and around the doors/

windows/ ventilation with 12 mm thick cement mortor

CM (1:4) and fixing with cement slurry & adhesive

including moulding of exposed edges as directed by

engineering in charge etc. complete.

52 Providing and fixing pre-cast Rubber Dye inter locking 72.20 Sqmt 685.42

concrete block 60mm thick with grade of concrete M200

pnumatic compressed by mechanically pressed and as

per approved design including 75mm Sand layer for

levelling and filling the joint with sand in proper line and

level etc complete.

Item Rate In

Description of Item Quantity Unit Amount

No figures

53 Providing and fixing M.S Safty Grills having 16mm Solid 18.20 Sqmt 2132.11

MS Squre bar Horizontally at every equal 0.10m C/C

distance and 2 no of bar Vertically at every equal 0.375m

C/C distance Fixing on around (5x40) mm Solid MS Patti

including cutting, welding and fabrication etc; including

one coat of primer of approved quality and two coats of

oil painting as per detail drawing etc. complete as per

directed Engineer in charge.

54 Providing erecting and fixing double coated PVC. (ISI) 5000.00 Litre 3.95

water tank of required capacity each with all necessary

fittings and connection etc. complete on terrace.

55 Providing laying and jointing in true line and level 50mm 54.00 Rmt 195.67

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

56 Providing laying and jointing in true line and level 40mm 34.00 Rmt 148.12

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

57 Providing laying and jointing in true line and level 25mm 30.00 Rmt 91.84

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

Item Rate In

Description of Item Quantity Unit Amount

No figures

58 Providing laying and jointing in true line and level 15mm 15.00 Rmt 72.65

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

59 Providing, laying and jointing in true line and level 160 10.00 Rmt 831.22

diametre U.P.V.C (Type B) conforming to IS 13592-1992

with one end plain and other end socketed with rubber

ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall

be jointed with each other with rubber lubricant, pipe

shall be fixed on wall using of PVC clamp of the size

mm diametre x 210 mm length x 196 mm heigh at every

2000 mm center to center or shall be concealed in walls

as directed including necessary fittings such as bends,

shoes etc. including testing of pipes and joints and

jointed with adhesive solvent cement including cost of all

materials.

60 Providing, laying and jointing in true line and level 110 20.00 Rmt 835.15

diametre U.P.V.C (Type B) conforming to IS 13592-1992

with one end plain and other end socketed with rubber

ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall

be jointed with each other with rubber lubricant, pipe

shall be fixed on wall using of PVC clamp of the size

mm diametre x 149 mm length x 145 mm heigh at every

2000 mm center to center or shall be concealed in walls

as directed including necessary fittings such as bends,

shoes etc. including testing of pipes and joints and

jointed with adhesive solvent cement including cost of all

materials.

Item Rate In

Description of Item Quantity Unit Amount

No figures

61 Providing, laying and jointing in true line and level 75 10.00 Rmt 715.08

mm dia. UPVC SWRType B pipe conforming to IS 13592-

1992 with one end plain and other end socketed with

rubbering and fitting conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall

be jointed with each other with rubber lubricant, pipe

shall be fixed on wall using of PVC clamp at every

mm c/c or shall be conceled in walss as directed

including necessary fittings such as bends, shoes etc.

including testing of pipes and joints and jointed with

adhesive solvent cement including cost of all materials.

62 Providing and fixing in PVC SWR cowel went 75mm dia 1.00 No 16.16

to pipes.(B) 75mm dia.

63 Providing and fixing in PVC SWR cowel went 110mm dia 4.00 No 29.29

to pipes.(B) 110mm dia.

64 Providing and fixing PVC SWR Nahni trap IS 14735 for 3.00 No 558.36

drain - 100 mm diameter with jali of the following

nominal diameter of self cleansing design with C.I scread

down or hinged grating including the cost of cutting and

making good the walls.

65 Providing and fixing wash down water closet (European 1.00 No 2853.25

type W C pan) with integral P and S trap including

jointing the trap with soil pipe in cement mortar 1:1 (1

cement five sand) including providing and fixing plastic

seat cover for wash down WC with CP brass hinges and

rubber buffers back plastic seat with a pair of C I or MS

bracket with complete fitting such as lead valve siphon

15 mm dia brass ball valve with polythene float CP brass

handle unions and couplings for connection with inlet

out let and over flow pipes 40 mm dia porcelain

enameled flush bend including cutting holes in walls and

making good the same connection the flush bend with

cistern and closet vitreous china.

66 Providing and fixing stainless steel grab 22 cm x 60 cm 1.00 No 1492.78

on door and handicapped toilet including all fixture and

accessary etc completed as per directed engineer in

67 Providing and fixing ball cock of approved. quality as 2.00 No 189.84

directed.(A) Copper Metal (ii) 50mm dia.

Item Rate In

Description of Item Quantity Unit Amount

No figures

68 Providing and fixing washbasin with single hole for pillar 1.00 No 1978.59

tap with C.I. or M.S. brackets painted white including

sutting holes and making good the same including Brass

waste, and M I fisher union fittings including pvc

connection and waste pipe & all necessary fittings For All

Floor (A) Vitreous China:(ii) Flat Back washbasin

mm x v 400mm size. (i) In white colour

69 Providing and fixing 600mm x 450mm bevelled edge 1.00 No 833.73

mirrror of superior glass mounted on 6mm thick A.C.

sheet or plywood sheet and fixing to wooden pluge with

C.P. brass screws and washers.

70 Providing and fixing C.P. brass towel rail comlete with 1.00 No 603.19

C.P. brass brackets fixed to wooden plugs with C.P. brass

scews.(B) 600mm x 20mm size

71 Providing and fixing screw down bib taps of following 2.00 No 186.83

size.(A) Brass screw down bib tap polished bright. (i)

72 Providing and fixing Urinal of approved quality including 1.00 No 1557.35

connection with trap and with integral longitudinal flush

pipe.(A) Squating plate pattern white earthenware

73 Providing laying (to level or slopes) and jointing 105.00 Rmt 665.48

reinforced concrete Light duty non-pressure pipes I.S.

class NP2 of the following internal diameter with collars

and butt ends prepared for collar joints including testing

of joints complete.(D) 300mm

74 Providing and fixing S.W. gully trap with C.I. grating brick 1.00 No 1246.92

masonry chamber and water tight C.I. cover with frame

of 300mm x 300mm size (inside) with standard weight

(i) Square mouth traps (B) 150mm x 100mm size P or R

75 Constructing brick masonry chamber for underground 8.00 No 3223.92

C.I. Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5

precast RCC cover 455mm x 610mm intenal dimensions

with frame (R.C.C. top slabe with 1:2:4 mix (1-cement :2-

coarse sand :4-graded stone aggregate 20mm size)

foundation concrete 1:5:10 inside plaster 15mm thick

with cement mortar 1:3 finished smooth with a floating

coat of neat cement on walls and bed concrete etc.

complete (i) Inside dimensions 455mmx 610mm and

450mm deep for single pipe line.

Item Rate In

Description of Item Quantity Unit Amount

No figures

76 Constructing brick masonry chamber for underground 5.00 No 3933.95

C.I. Inspection C.I. Inspection chamber and bends with

briocks having croshing strength not less than 35Kg. Cm2

in C.M. 1:5 precast RCC cover 500mmx 700mm intenal

dimensions with frame (R.C.C. top slabe with 1:2:4 mix (1-

cement :2- coarse sand :4-graded stone aggregate 20mm

size) foundation concrete 1:5:10 inside plaster 15mm

thick with cement mortar 1:3 finished smooth with a

floating coat of neat cement on walls and bed concrete

etc. complete (i) Inside dimensions 500mmx 700mm and

450mm deep for single pipe line.

77 Extra over items for every additional depth of 0.1M. of 4.00 No 242.39

part thereof beyond 450mm depth for Brick masonry

chamber.(i) for 455mm x 610mm size.

78 Extra over items for every additional depth of 0.1M. of 4.00 No 264.86

part thereof beyond 450mm depth for Brick masonry

chamber.(i) for 500mm x 700mm size.

79 Providing and fixing MS Ladder of required pattern with 300.00 Kg 101.00

MS flats(30x3mm) or round or square bars (12mm) at

required spacing & with round headed bolts and nuts or

screws or welding including primer coat of approved

quality and two coats of oil paintas as directed by

engineer in charge

80 Constructing drinking/Handwash Platform of 18 mm 1.20 Sqmt 5248.97

thick Polished Black Granite having 0.45m width and

0.60m height including 0.60m support at every 0.7m c/c

with cementing Materials / adhsives including makeing

necessary grooves in walls iwith all labour material of

approved quality incl. full moulded round front edge

granite strip of one side polished and jointed with grey

cement slurry including rubbing and polishing etc.

complete for all floors

81 Constructing Kitchen Platform of 16mm to 18 mm thick 3.20 Sqmt 4192.51

Polished Granite at top and 25 mm thick Kota stone slab

one side polished at bottom with cementing Materials /

adhsives including makeing necessary grooves in walls

with Vertical sandwich two Kotastone 25 mm support

every 60 cm centre to centre or as required including all

labour material of approved quality incl. full moulded

round front edge granite strip of one side polished and

jointed with grey cement slurry including rubbing and

polishing etc. complete for all floors

Item Rate In

Description of Item Quantity Unit Amount

No figures

82 Providing and fixing Kitchen sink with C.I. or M.S. 1.00 No 3586.51

brackets, painted white including cutting holes in walls

and making good the same with including all fittings. (C)

Vitreous China Sink.(i) 600mm x 450mm x 150mm size

etc. directed by engineer in charge.

83 Providing and fixing 25 mm thick shutters for Cupboards 3.20 Sqmt 4263.21

etc. including S.S. hinges, Aldrop, handle,stopper and

other required fixtures with necessary screws. (A) ply

with both side lamination (i) Fully Panelled including

priming coat and two coat of oil paint etc. directed by

engineer in charge.

84 Providing and fixing in position 300 mm high, 150 mm 20.00 No 1333.20

wide English letters made from 1.0 mm thick stainless

steel sheet as directed by Engineer in charge with all

necessary tools & plants etc. complete.

85 Providing and fixing in position 150 mm high, English 20.00 No 686.80

letters made from 1.0 mm thick stainless steel sheet as

directed by Engineer in charge with all necessary tools &

plants etc. complete.

86 Providing and fixing of Ridge flashing for roof panel shall 33.90 Sqmt 677.31

be made out of 0.5 mm thick pre coated GI sheet . The

Precoated sheet shall be of minimum 240 mpa steel

grade confirming to IS 14246:1995 and shall have zinc

coating of minimum 120 gsm as per IS:277:1992 , 5-7

microns epoxy primer on both side of the sheet and

polyester top coat 15-18 micron. The PPGI Sheet shall

have plastic protective guard film of minimum

microns to avoid scratches during transportation. The

ridge shall be fixed to the steel members by pop rivet or

self drilling/self stitching fastners @ maximum 450 mm

c/c along length of capping/flashing etc complete.

87 Steel work, welded in built up sections framed work 2303.30 Kg 90.48

including cutting,hoisting, fixing in position and applying

a priming coat of read lead paint. (A)In beams and joists,

hannels angles Tees, flats, with connecting plates or angle

cleats as in main and cross beams. Hip and jack rafters,

purlins conneted to common rafters and the like.

Item Rate In

Description of Item Quantity Unit Amount

No figures

88 Constructing brick masonry chamber for underground 1.00 No. 7180.44

C.I. Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I.

cover with frame (Light duty) 455mm x 610mm intenal

dimensions, total weight of cover with frame to be not

less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame

15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2-

coarse sand :4-graded stone aggregate 20mm size)

foundation concrete 1:5:10 inside plaster 15mm thick

with cement mortar 1:3 finished smooth with a floating

coat of neat cement on walls and bed concrete etc.

complete.(iii) Inside dimensions 600mm x 850 mm and

450mm deep for pipe lines with three or more inlets.

89 Providing and fixing and floor 10.0 Kg. F/Cm2 working 50.00 Rmt 336.24

pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge compression

type fittings, wall clipsetc. including making good the

wall ceiling and floor.(G)110 mm

90 Providing and fixing and floor 10.0 Kg. F/Cm2 working 10.00 Rmt 696.90

pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge compression

type fittings, wall clipsetc. including making good the

wall ceiling and floor.(G)180 mm

91 Providing junction for rain water juncton chamber of size 1.00 Nos. 9470.77

0.60x0.60x0.75m with excavation of size 1.96x1.96 m &

0.15m thick c.c.1:2:4 bed concrete including brick

masonary wall in CM 1:6 of 0.75m height & 0.23m thick

with 15mm thick cement plaster inside & outside &

1.06x1.06 RCC (1:2:4) slab of thickness 0.15m with CRS

steel and 0.60mx0.45m cast iron manhole cover with

frame weight not less than 35 kg as per directed by

Engineer-in-charge

92 Providing and installation Recharge pit of “RAIWOHA” 1.00 Nos. 109645.60

Make 3 layer RCC Precast Injection well system of size

1.5 meter Dia. X 3.4 Meter Height rein forced concrete

precast three layer module with 6” dia x 12” dia. V wire

screen of 0.75mm x 1.0 mm Slot size in SS 304 material

and 1.0 meter height with MS Top cover and required Air

vent including all necessary excavation and

transportation at site including required filter media for

the recharge system as per site requirement.

Item Rate In

Description of Item Quantity Unit Amount

No figures

93 Drilling of min. 250 mm dia. bore hole in all strata 30.00 Rmt 1252.32

including dualover burden strata by combination

DR/DTH rig including lowering 200 mm dia MS ERW

pipes in bore hole and testing etc.all work as per directed

engineer incharge.

94 Supplying slotted PVC pipes of approved quality at site of 30.00 Rmt 555.50

work confirming to IS. 1239/1974 180mm dia.

95 Box cutting the road surface to proper slope and camber 52.00 Cum. 104.20

for making a base for road work including removing the

excavated stuff and depositing on the road side slope as

directed upto upto All lift and lead..

96 Providing, laying and compacting natural sand & gravel[ 8.00 Cum. 688.82

C.B.R. not less than 20%] below sub base course

including carriage of materials spreading in uniform

layer manually on prepared base and compacted with

vibratory roller to achieve desired density including all

materials, labour etc. complete.

97 Construction of granular sub-base 150 mm thick by 19.25 Cum. 1006.97

providing coarse graded machine crushed B.T. material

satisfying MOST specification of grading I (B.T. stone

aggregate 53 mm to 26.5 mm 35 %, 26.5 to 4.75 mm -

% and 2.36 mm below - 20 % )including spreading in

uniform layer with motor grader on prepared surface,

mixing by mix in place method with rotavator at OMC

and compacting with vibratory roller to achieve the

desired density etc. complete.

98 Providing and laying wet mix macadam base course 250 22.00 Cum. 1064.54

mm thick in two layers using machine crushed B.T. chips

as per required gradation mixing with required optimum

quantity of water, conveying the mix to site of work,

spreading in to grade and camber with mechanical paver

and consolidation each layer with vibratory roller

including cost of material labour plant and equipment

etc. complete.

99 Compaction and finishing of cement concrete road by 68.00 Sqm 65.65

trimix process providing extra Labour charges for the

trimix vacume dewatering service process on cement

concrete road sutface by using vacuum dewatering pump

floater surface vibrator including making groves and

rough finish to surface including leveling etc complete.

Item Rate In

Description of Item Quantity Unit Amount

No figures

100 Providing and Laying homoginious Grey cement based 36.00 Rmt 361.64

concrete kerbing of size 30 cm x 30 cm x 10 cm size as

per detailed drawing having grade of concrete M25

grade, including necessary excavation, BBCC 1:5:10

cm as per ddetailed drawing fixing in line and level,

filling joints in CM 1:3 with smooth finished, white

washing three coats etc. complete as directed by

Engineer in charge.

101 Providing and fixing concertina coil fencing with 63.00 Rmt 864.56

punched tape concertina coil 600 mm dia 10 mt openable

length having 50 no rounds per 6 mt length, upto 3mt

height of wall with existing angle iron (50mm x50mm

x5mm )requird shaped As per Directed Engeenier in

charge. placed 2.4mt or 3.00mt apart and with

horizontal R.B.T. reinforced barbed wire(3 mm) , stud

tied with G.I. staples and G.I. clips to retain horizontal,

including necessary bolts or G.I.barbed wire tied to angle

iron, all complete as per direction of Engineer-in-charge,

with reinforced barbed tape (R.B.T.)/Spring core (2.5

mm thick) and weight 43.478 gm/meter at compound

wall for ESR M4/ intakewell.

102 Providing, supplying, delivering and fixing low-height 2.00 No. 13357.25

Executive Storage Cabinet (600 mm w x 750 mm H )of

approved design and size, fabricated from 19 mm thick

BWP Grade IS:710 plywood for top, sides, bottom,

shelves, partitions and shutters, with 6 mm BWP

plywood back panel, finished with 1.0 mm thick premium

decorative laminate on all exposed surfaces and

balancing laminate on internal surfaces, complete with

mm thick PVC edge banding on exposed edges, lockable

hinged shutters with adjustable shelves, central drawer

unit comprising utility drawers fitted with heavy-duty

telescopic ball-bearing channels, soft-close SS hinges,

SS/Aluminium handles, cam locks, adjustable nylon

levelling feet, all necessary screws, fittings and hardware

of approved make (Hettich/Häfele/Ebco or equivalent),

including cutting, edge finishing, polishing,

transportation, loading, unloading, assembly, installation

and all labour, materials, tools, taxes and incidental

charges complete as per approved drawings and

directions of the Engineer-in-Charge.

Item Rate In

Description of Item Quantity Unit Amount

No figures

103 Providing and supplying visitor or guest chair with seat 12.00 No. 4413.70

and back made of 12 mm thick hot-pressed plywood,

upholstered with changeable fabric upholstery covers (as

per requirement) and molded PU foam, along with

molded seat and back covers. The back foam shall be

contoured to provide lumbar support for enhanced

comfort. The chair dimensions shall be approximately

cm (W) × 38 cm (H) for the back, and 45 cm (W) × 43 cm

(D) for the seat. The PU foam shall be molded with a

density of 45 ± 2 kg/m³. The armrests and legs shall be

fabricated from powder-coated mild steel (MS) structure

securely fixed to the MS structure using all necessary

hardware. It shall be confirmed and approved in advance

by the Architect, along with a description and image, or

as directed by the Engineer-in-Charge.

104 Providing and supplying 3-seater sofa made using 19 mm 1.00 No. 18003.25

thick plywood (M1) structural frame, supported by

stainless steel (S.S.) legs with all required supports,

fixtures, and fastening hardware (M14). The seat, back,

and handle portions shall be cushioned with PU foam of

32 density (M22), with thickness as per design, and

additionally covered with 14 mm thick PU foam (M22)

and Madarpat fabric. The entire sofa shall be upholstered

with fabric (M26) or leather as suggested and approved

by the Architect, and finished on the seat, back, and all

visible sides as per architectural drawings. The item shall

be executed in complete compliance with the Architect’s

design and the instructions of the Engineer-in-Charge.

Refer to the drawing size: 2.10 m (L) × 0.95 m (W) ×

m (H). It shall be confirmed and approved in advance by

the Architect, along with a description and image, or as

directed by the Engineer-in-Charge.

Item Rate In

Description of Item Quantity Unit Amount

No figures

105 Providing and supplying Centre Table / Corner Table / 1.00 Sqmt 15630.76

Tipoi with Glass Top, made with 19mm thick plywood

(M1) structure, finished with 1.0 mm thick decorative

laminate sheet (M24) as specified and approved by the

Architect, and fixed with necessary fixtures and fastening

(Hardware) (M14). The table shall rest on four solid

wooden legs of size 50mm x 50mm made from C.P.

teakwood (M5). A 50mm x 50mm wooden frame shall be

provided at the top for support. Over this frame, a 75mm

wide plywood patta (M1) shall be fixed on all sides,

finished with approved melamine polish (M29). The

patta shall have a 2 mm wide groove to securely hold an

8 mm thick toughened glass top (M27) with polished

edges. Internal MS support bars and a center stiffener

shall be provided as per drawing for structural stability.

Table size shall be 950 mm (L) x 500 mm (W) x 450 mm

(H). Complete as per Architect’s drawing and as per

instructions of the Architect & Engineer-in-Charge.

106 Providing and supply Photo Frame size 6'0"x 3'0"of 1.00 No. 6388.25

Aniumal Pictures made of Teakwood Border Patti of size

1" x 1/2" with melamine polish finish with 3 mm glass

and inside the picture of Aniumals on Photo paper with

high resolution picture quality and sticked on MDF as

fixture, fasteners,labour , material etc compelet. All work

shall be completed as per the design and instructions of

the Engineer-in-Charge. It shall be confirmed and

approved in advance by the Architect, along with a

description and image, or as directed by the Engineer-in-

107 Providing and supplying roller blinds to be installed with 4.00 Sqmt. 2113.93

precision across all designated window openings. The

blinds shall be water-resistant, mounted on durable

powder-coated aluminum head rails, and fitted with

stainless steel drive rods for smooth manual operation.

The complete assembly shall be manually operated and

must conform to ISI standards. All fixtures, fittings, and

components required for proper installation shall be

included. The work shall be executed complete in all

respects, or as directed by the Architect and Engineer-in-

Charge. It shall be confirmed and approved in advance by

the Architect, along with a description and image, or as

directed by the Engineer-in-Charge. (M34)

Item Rate In

Description of Item Quantity Unit Amount

No figures

108 Providing, supplying, delivering and fixing Executive 2.00 Sqmt 29795.00

Office Table of approved design and size ( 900 (W) ×

(H)) mm manufactured from 25 mm thick BWP Grade

IS:710 plywood for the table top and 19 mm thick BWP

Grade plywood for side panels, modesty panel, drawer

units and all structural members, finished with 1.0 mm

thick premium decorative laminate on all exposed

surfaces and balancing laminate on internal surfaces,

complete with 2 mm PVC edge banding to exposed edges,

double pedestal storage with four drawers (two on each

side) and three central utility drawers, heavy-duty

telescopic ball-bearing drawer channels, central locking

arrangement, SS powder-coated/antique finish handles,

cable management grommet, adjustable nylon levelling

feet, decorative mouldings, all necessary screws, fittings

and hardware of approved make (Hettich/Häfele/Ebco

or equivalent), including cutting, edge finishing,

polishing, transportation, loading, unloading, assembly,

installation, testing and commissioning, and all labour,

materials, tools, taxes and incidental charges complete as

per approved drawings and the direction of the Engineer-

in-Charge.

109 Providing, supplying, delivering and fixing low-height 5.00 Sqmt 18685.00

Executive Storage Cabinet (600 mm w x 750 mm H )of

approved design and size, fabricated from 19 mm thick

BWP Grade IS:710 plywood for top, sides, bottom,

shelves, partitions and shutters, with 6 mm BWP

plywood back panel, finished with 1.0 mm thick premium

decorative laminate on all exposed surfaces and

balancing laminate on internal surfaces, complete with

mm thick PVC edge banding on exposed edges, lockable

hinged shutters with adjustable shelves, central drawer

unit comprising utility drawers fitted with heavy-duty

telescopic ball-bearing channels, soft-close SS hinges,

SS/Aluminium handles, cam locks, adjustable nylon

levelling feet, all necessary screws, fittings and hardware

of approved make (Hettich/Häfele/Ebco or equivalent),

including cutting, edge finishing, polishing,

transportation, loading, unloading, assembly, installation

and all labour, materials, tools, taxes and incidental

charges complete as per approved drawings and

directions of the Engineer-in-Charge.

Item Rate In

Description of Item Quantity Unit Amount

No figures

110 Providing, supplying, delivering and fixing Wall Mounted 5.00 Sqmt 15655.00

Glass Storage Cabinet ( 500 mm W x 600 mm H )of

approved design and dimensions, fabricated from 19 mm

thick BWP Grade IS:710 plywood for top, bottom, sides,

shelves and partitions with 6 mm thick BWP plywood

back panel, finished with 1.0 mm thick premium

decorative laminate on all exposed surfaces and

balancing laminate on internal surfaces, complete with

mm thick PVC edge banding on exposed edges, 5 mm

thick clear toughened glass shutters with powder-coated

aluminium frame (or frameless glass with SS patch

fittings as approved), adjustable shelves, soft-close SS

hinges, SS handles, cam locks, wall mounting with heavy-

duty MS brackets/anchor fasteners, all necessary screws,

fittings and hardware of approved make

(Hettich/Häfele/Ebco or equivalent), including cutting,

edge finishing, transportation, loading, unloading,

installation, alignment, testing and all labour, materials,

tools, taxes and incidental charges complete as per

approved drawings and directions of the Engineer-in-

111 Providing, supplying, transporting, erecting and 2.00 No 65650.00

commissioning Insemination Crate cum Travis Lifting

Machine suitable for safe restraining and lifting of

cattle/buffalo during artificial insemination, veterinary

treatment, hoof trimming and pregnancy diagnosis,

overall size 2200 × 900 × 2200 mm, fabricated from

heavy-duty MS seamless tubes conforming to IS

using 50 NB, 40 NB and 32 NB tube sections, complete

with front and rear swing gates, adjustable side panels,

belly support arrangement, locking chains, lifting eyes,

restraining rings, anti-slip floor support, heavy-duty

chain pulley/block lifting mechanism, locking pins,

hinges, bushes, clamps, fasteners and all necessary

accessories, designed for a safe working load of

800–1000 kg, finished with proper surface preparation

followed by one coat of zinc-rich metal primer and two

coats of synthetic enamel paint or epoxy/powder-coated

finish of approved colour, including all welding, grinding,

fabrication, loading, unloading, transportation, erection,

testing, commissioning and all labour, materials, tools,

tackles and incidental charges complete as per approved

drawings, specifications and the directions of the

Engineer-in-Charge.

112 Drilling pilot borehole of size 250/300 mm at above site 80.00 Rmt 573.68

by mud flush direct rotery rig.

Item Rate In

Description of Item Quantity Unit Amount

No figures

113 Reaming of 250/300 mm dia.Pilot borehole to size 550 80.00 Rmt 349.46

mm dia. Incliding assembling ,lowering housing ,casing

strainerpipers with gravel packing and clayball packing

114 Development of cach water bearingzone coming across 1.00 Job 27191.22

the full depth of tubewell by lowering 100 mm

dia.Droplineand 32 mm dia airline for each water

bearing Zone with suitabale capacity air compressar up

to avilability of sand free discharge.

115 900 CFM /200 PSI capacity air compressar upto the 1.00 Job 27603.30

availability of sand free discharge for upto 250 mtrs

116 Supply of M.S. E.R.W. plain end medium duty pipe 80.00 Rmt 3605.70

confirming to IS 4270/2001 with latest amendments Of

size 250 mm dia (minmum thicknes of 7.1 mm)

117 Screen Slotting of MS ERW balnce pipe with size of slot 9700.00 slots 0.24

6.75 cm X 6.35 cm X 3.12 mm for 250 mm dia pipe

118 Supply of miscellenious bore material suitable to 250 1.00 Pair 2037.91

mm dia pipes as following (A) MS Bore clamps made

from M.S. plate with 3 holes on either side with nuts &

bolts of std make of size 900X100X16 mm flat suitable

for 250 mm dia pipe.

119 Supply of miscellenious bore material suitable to 250 1.00 No 1161.62

mm dia pipes as following (B) MS Bore Plug having

100mm height made from M.S. plate with 3 holes at equal

distance on circumferrence for nut-bolts type, locking

arrrangement with nuts-bolts & lock nuts of std make

complete from 5 mm thick M.S. plate suitable for 250mm

120 Supply of miscellenious bore material suitable to 250 1.00 No 1065.02

mm dia pipes as following (C) MS Bail Plug having length

0.45 mtr from medium class pipe as per I.S. suitable for

250 mm dia pipe.

121 Supply of miscellenious bore material suitable to 250 107.00 NO 91.71

mm dia pipes as following (D) Steel bent plate suitable

for ERW pipe for 250mm dia (size:200 X 150X6 mm)

123 Electrologging of Pilot bore hole with carting. 1.00 Job 18180.00

124 Geohydrological ground water investigation including 1.00 No 14428.86

vehicle charges for three phase DTH bore/DR tube well

including water sample testing & chemical analysis

125 Providing, supplying and commissioning ISI mark CI D/F 1.00 No 5401.48

Reflux Valves of following class and diameter including

all taxes, insurance, transportation, freight charges,

octroi, inspection charges, loading, unloading,

conveyance to departmental stores stacking etc.

complete. Reflux valves PN 1 IS 5312 with ISI mark size:

Item Rate In

Description of Item Quantity Unit Amount

No figures

126 Manufacture, supply and delivery of following ISI marked 80.00 Rmt 152.51

HDPE pipes (IS:4984/1985 with latest amendment)

having material Grade PE-80 in approximate 100 meter

coil length or as per GWSSB requirement with SS

nipple at both ends having 11 TPI threads as per

specifications, press fitted and bolted having nominal

diameter as under as per detailed technical

specifications.

127 Supplying FIRE bucket round bottom of 9 litres capacity 2.00 Nos 252.50

made out of 24 gauge G.I Sheet with extra handle at

bottom duly painted white inside and Red out side with

FIRE mark. Filled with dry-sand and kept on existing

stand provided or hung on wall hook.

128 Supplying and erecting floor mounting Stand for keeping 1.00 Nos 4040.00

four nos. of FIRE buckets comprising 1500 mm in length,

900 mm height frame made out of 30mm x 30 mm x

mm angle iron with cross suports legs, welded with

hooks and duly painted with one coat of red lead and two

coats of approved enamelled silver paint.

129 Supply, Filling and Fixing of following type of approve 5.00 Nos 5555.00

make fire extinguishers CO2 type fire extinguisher,

Capacity 4.5 Kg. (conforming to IS-2878).

130 Design , Supply and installation of Safety Signage made of 100.00 SQ 11.11

Zinc Sulphilde based glow in dark , Rigid sheet with High INCH

Luminous property enclosed in a transperent weather

proof UV stabilized plastic pasted on 3 mm thick clear

acrylic sheet such as EXITS, EMERGENCY EXIT, DO NOT

USE LIFT DURING FIRE, FLOOR MARKINGS, FIRE LIFT,

STAIRCASE EXIT, FIRE ALARM CALL POINT, FIRE HOSE

REEL, FIRE HYDRANT POINT etc.

131 Supply, Filling and Fixing of following type of approve 5.00 Nos 2626.00

make fire extinguishers Dry powder type, Capacity 5 Kg.

(conforming to IS:2171 with cylinder fully charged).

132 Bowing and developing flowering plants grown in nusery 10.00 No. 30.30

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith of soil packed in

polithyline bag or Earthern pot. Including organic &

chemical fertilizer Pesticides, fungicides, hormones &

maintaining the plants up to three months as deserted.

Bottol palm.

Item Rate In

Description of Item Quantity Unit Amount

No figures

133 Bowing and developing flowering plants grown in nusery 5.00 No. 60.60

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as deserted Trinagle Plan.

134 Bowing and developing flowering plants grown in nusery 10.00 No. 60.60

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as Jasud

135 Bowing and developing flowering plants grown in nusery 10.00 No. 75.75

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as Croton

136 Bowing and developing flowering plants grown in nusery 10.00 No. 10.10

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as deserted green mahindi

137 Bowing and developing flowering plants grown in nusery 5.00 No. 15.15

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as deserted New block ficus.

138 Labour charges for planting various plantsafter proper 50.00 No. 40.40

anti termite treatment in pits including placing property

and filling the pit with requred prepared mix soil and

wetering and dispporting etc complete.

139 Maintance of the garder for 60 days after Complition of 3 1.00 Job. 10100.00

month stipulated period is completed for plantation o

lawn and plants including applying second round of

proper antitermite tretment.

Item Rate In

Description of Item Quantity Unit Amount

No figures

140 Providnig and fixing to wall ceiling and floor 80 Schedule 5.00 Rmt 442.04

Syntex / Astra (CPCV) or equivalent of the following

nominal bore tube fittings and clamps the wall ceiling

and floor (C) 40 mm

141 Providing and fixing consealed to wall, ceiling and floor 5.00 Rmt 205.00

80 Schedule Syntex / Astral (CPVC) or equivalent brand

of the following nominal bore tube fittings and clamps

including Making goods the wall ceilling and floor (A)

142 Providing and fixing brass screw doen stop cock (A) 15 1.00 Rmt 287.85

143 Rubber Hose pope 15 mm dia of approved brand and 30.00 Rmt 25.25

144 Providnig and fixing G I Nipple as directed. 1.00 No. 20.20

145 Point wiring for Light / Bell with 2-1.5 sq.mm & earth 16.00 Pts. 582.77

wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires up

to 10 mtr length , in below type of pipe erected with 6A

Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured/metallic/white front plate

modules erected on / in wall / ceiling as per pipe

erected, with necessary Lamp holder/ceiling rose /

H.D.Connector as directed. (f) with medium class Rigid

PVC pipe and accessories erected concealed in

wall/ceiling complete cat lll

146 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 8.00 Pts. 809.01

1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade

FRLS PVC insulated multi strand copper wires up to

mtr length, in below type of pipe erected with 6A

Modular type switch and hum free EME step type

electronic fan regulator mounted and accessories with

earth continuity of following type erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured/metallic/white front plate

modules erected on / in wall / ceiling as per pipe erected.

with necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat- III

147 Point wiring for on board Looped Plug with 6A Modular 9.00 Pts. 309.06

type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate

modules erected on / in wall / ceiling with following

type accessories cat lll

Item Rate In

Description of Item Quantity Unit Amount

No figures

Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge.

148 (7) Blank Plate Single Cat.III 20.00 Nos. 25.25

149 (4) TV Co-axial Socket outlet CAT lll 4.00 Nos. 160.59

150 (9) 16 Amp. SP one way switch Cat.III 4.00 Nos. 180.79

151 (10) 6/16Amp. Universal socket Cat.III 4.00 Nos. 199.98

152 Providing and erecting ISI mark Medium class RIGID PVC 50.00 Mtr. 24.24

PIPES of following size complete to be erected on/in wall

or ceiling erected with necessary PVC fittings & Junction

boxes fixed with adhesive solution & Clamps with

following dia of pipes, in approved manner as directed

153 Providing and erecting Mains with 1.1 KV grade FRLS 159.00 Mtr. 104.03

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected concealed in

/flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size

(A) with medium class Rigid PVC pipe and accessories

(b) 2 wire 2.5 sq. mm

providing and erecting Mains with 1.1 KV grade FRLS

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall /

ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size Cat.III

(A) with medium class Rigid PVC pipe and accessories

154 (a) 2 wire 4 sq. mm 17.00 Mtr. 140.39

155 (h) 4 wire 6 sq. mm 25.00 Mtr. 326.23

156 Supplying and erecting Flexible PVC insulated multi 36.00 Mtr. 58.58

strand multi core 1.1 kv grade ISI marked copper wires

of following size to be erected as directed.

e) 1.50 Sq.mm 3 core round PVC sheathed

157 Providing & Erecting approved make following size of TV 25.00 Mtr 62.62

Co-axial flexible cable comprising inner conductor of

solid bare copper insulated with Foam PE & Secondary

conductor made of poly - Aluminium film bonded Al.

Braids @ suitable coverage overall sheathed with black

PVC insulation. (e) RG-11

158 Decorative call bell Ting-tong box type 250 volts 1.00 Nos. 71.71

complete erected

Item Rate In

Description of Item Quantity Unit Amount

No figures

159 Supplying and erecting LED indoor fittings with LEDs of 12.00 Nos. 535.30

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/ aluminium die

cast powder coated and high U.V. & corrosion resistance

with diffuser with company mark/name 160V to 270V,

Power Factor more than 0.95, THD < 15%, CCT 3000 K

to 6500K, Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %( fitting required LM-79 &

LM-80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The

between the ranges shown.) (A) Tube Light with integral

driver(v) 36-40 Watts, Surge-2 KV, IP-20, conventional

feet cat lll

160 Supplying and erecting led lamps with following wattage 1.00 Nos. 112.11

capacity of 220 to 240 voltage, minimum 15000 burning

hours life, 500 V in built-surge protection,Polycarbonate

diffuser, mounting suitable for E14 / E27 / B22 lamp

holders, pf >=

(A) LED Lamps integral type, with PC diffuser suitable

LAMP holder (A) LED Lamps integral type, with PC

diffuser suitable LAMP holder (ii) 5 to 8 watts cat lll

161 Supplying and erecting LED street light / Flood light 6.00 Nos. 4248.06

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated

and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to

V,Power Factor more than 0.95, THD < 10 %, CCT

K to 5700K,Uniformity ratio >0.45, Luminaire efficacy>

100 lumens/watt . LED driver efficiency > 85 %.( fittings

required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of

wattage capacity between the ranges shown.) (A) Street

Light (IP-65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage

protection. (ii) above 48 to 59 Watts cat lll

162 providing and erecting Miniature circuit breaker single 6.00 Nos. 297.95

pole 0.5A to 2A system and having breaking capacity

KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark cat lll

Item Rate In

Description of Item Quantity Unit Amount

No figures

163 providing and erecting Miniature circuit breaker single 12.00 Nos. 123.22

pole 6A to 25A suitable to operate on 240 V A.C. system

and having breaking capacity 10 KA to be erected in

existing box. confirming to IS 8828/1996 with ISI Mark

164 Providing & erecting 240 V MCB double pole switch for 3.00 Nos. 362.59

motor & inductive load (C Curve) having 10 KA

breaking capacity & confirms to IS : 8828 in existing box

having following capacity (B) 40 Amp. Cat.III

165 Providing & erecting 415 V MCB Four Pole for Motor & 2.00 Nos. 811.03

Inductive Load (C Curve) having 10KA breaking capacity

& confirms to IS :8828 in existing box having following

capacity (c)63 Amp. Cat lll

166 Plastic enclosure fitted with DIN rail suitable for 1.00 Nos. 52.52

incorporating One / Two nos. MCB

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to

IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for

167 (B) three phase incoming and single phase horizontal 1.00 Nos. 2339.16

type outgoing Per phase isolation type (PPI) (b) sheet

steel double door(iii)8 way

168 providing and erecting Approved make RCCBs 3.00 Nos. 2458.34

conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V,50Hz.

having characteristic of quick action & tripping with all

advance feature & do not incorporate any electronic

component. for following Max. rating erected as directed

(ii) 40Amps. DP cat lll

169 Providing and erecting HOT deep Galvanised iron strip 8.00 Kg. 77.77

wire 4.064mm to 1.626mm.

Item Rate In

Description of Item Quantity Unit Amount

No figures

170 Supplying & erecting in earthpit of minimum bore dia. 2.00 Nos. 5842.85

225mm size approved make Safe Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having Outer

pipe dia of 80 mm having 80-200 Micron galvanising,

Inner pipe dia of 40 mm having 200-250 Micron

galvanising, connection terminal dia of 14 mm with

constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for

following type of applications with chamber and heavy

duty cover.(approved make OEM has to submit test

certificate including value of earth resistane of

installation. [A] For electrical installation up to 440 V

Length of Pipe - 1 Mtr Back filling compound - 1 Nos. of

Bag of 15 Kgs.

171 Providing and erecting Pipe type earthing having 150 6.00 Nos. 368.65

cms.long and 2.5 cms. dia. galvanised iron pipe with

coupling and buch buried in specially prepared earth pit

complete with necessary 8 SWG earth wire.

172 For using salt and charcoal / coke as required for pipe 6.00 Nos. 171.70

type earthing.

173 Providing and erecting XLPE (IS:7098)(I)-88 ISI 140.00 Mtr 151.50

armoured cable multistrand / Solid Aluminium

conductor for 1.1 KV. to be laid on wall with necessary

clamps or in existing trench / pipe of following size of

cables (B) 4 core 6 Sq. mm

174 Making trench in soft soil of suitable width of 90 cm deep 125.00 Mtr. 55.55

for laying cable or locating the fault all over the run and

back filling the same and making the surface as normal

175 Making trench in Hard Murrum / Tar Road of suitable 10.00 Mtr. 74.74

width of 90 cm or required depth for laying any size of

cable or locating the fault all over the run and back filling

the same and making the surface as normal ground.

176 Providing & laying approved make ISI marked HDPE 130.00 Mtr. 108.07

6Kg / cm2 (Class-3) as per IS:4984:1995 PE-80 to be

erected at road crossing on or floor as directed for laying

of cable. The pipes as following size of dia & weight per

mtr.(A) 40 mm inner Dia.

177 Providing and, fixing heavy duty flange type brass cable 12.00 Nos. 38.38

gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for

following size of cables. .(b) 2 to 4 core 6 Sq. mm

Item Rate In

Description of Item Quantity Unit Amount

No figures

178 Solder less crimping type Aluminium lugs conforming to 48.00 Nos. 6.06

IS suitable for cable of following size evenly crimped with

high pressure tool & connected to switchgear terminals

with brass/cadmium plated nut bolts in an approved

manner. (A) 1.5/ 2.5/4/6 Sq.mm

179 Providing & erecting Approved make Ceiling Fan with 6.00 Nos. 1738.21

double ball bearing ISI mark with condenser A.C.230V

Hz. 1400 mm. sweep complete, canopy erected on

existing hook or clamp with earthing [ Make shall be

approved by Engineer in Charge]

180 Supplying and erecting 19 / 20 mm. nominal bore 6.00 Mtr. 108.07

Medium Class M.S. Pipe down rod erected duly painted

for fan complete with proper insulation without leakage

and earthing.

181 Supplying & erecting fan hook box of 10 mm M.S. round 6.00 Nos. 108.07

bar bounded to the RCC bars up to 50mm length each

side and pierced through a 16 Gauge M.S. box / Heavy

Duty PVC box complete erected concealed in Ceiling with

necessary finishing.

182 Providing 2.5mm.thick laminated acrylic sheet to cover 6.00 Nos. 18.18

the fan hook or Fan box.

183 Supplying & erecting approved make low noise 1.00 Nos. 1366.53

decorative exhaust fan having square frame ABS body

with inbuilt lowers & square frame. 200mm with

1350RPM Cat.II

184 Supplying and erecting approved make Octagonal pole 6.00 Nos. 7561.87

made from HR sheet steel. The pole should be made as

per IS. and shall be coated with hot dip galvanizing as per

IS 2629/2633/4759, suitable suspend local wind speed

with integral Junction box consist of terminal plate of min

6mm Hylam sheet, standard profile 35mmX7.5mm Din-

Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With

Suitable foundation (Included) as per details given by

manufacturer considering site requirement.(C) 5 Mtr.

Long 70 mm Top X 130 mm bottom dia, 3 mm thickness

with 200mmX200mmX12mm base plate, 4-M16 Bolts

and 600mm long with necessary G.I. J Bolts .Approx Pole

weight 46 kg

Item Rate In

Description of Item Quantity Unit Amount

No figures

185 Supplying and erecting Street light pole bracket 6.00 Nos. 450.46

comprising main B Class MS pipe of 4.2 cm/require

outside dia. complete with suitable B Class M.S. sleeve

tubing of approx. 45cms.length and suitable for

76.5mm/80mm/require size of pole top having nuts and

bolts for fixing the brackets and having spread of 0.5 mtr.

Length with 110 deg.with vertical plane and suitable

welded stiffener reducer and nipple with check nut

complete painted with one coat.of Red oxide / PU base

primer and two coats of Aluminium / PU paint. paint

with following nos of arms. [A] Single Arm bracket

186 Supplying & erecting IP 55 grade following size section 1.00 Nos. 3595.60

pillar fabricated from joint less M.S. Sheet with angle iron

legs made from jointless M.S. Angle with cable clamps to

be buried in ground to have appropriate erection to work

uniform until erected with cement concrete foundation

and 45 cm high bricks work finishing with plaster etc.

hinged double door internally supported on both side,

with internal and outside looking arrangement with look

and keys in duplicate 35 x 35 x 5 mm M.S. Angle of Two

Nos. one is welded and other with nut and bolt for

erecting Bakelite sheet. Painting the Section Pillar inside

and out side with three tank powder coated paint.

section pillar roof should be without joint with water

leakage proof & tested as per IP 55 test & followed by IS

2147 of 1962(B) 75 X 60 X 45 cm section pillar

fabricated from 16 Gauge MS Sheet with angle iron legs

45 cm long made from 35 X 35 X 5 mm thick MS angle.

187 Supplying and erecting HYLAM sheet on existing angle 1.35 Nos. 385.82

iron frame.for following thickness (A) 2mm

188 Providing & erecting open well type horizontal mono 1.00 Nos. 10193.93

block pump set with stainless steel body having

following specification (C) 1 H.P. single phase open well

motor pump set suitable for 185 LPM discharge @

mtr. head, suitable for 32 mm dia. Delivery pipe with

control panel. Cat-II

Item Rate In

Description of Item Quantity Unit Amount

No figures

189 Supplying & erecting approved make motor control 1.00 Nos. 7722.46

cubical panel (Direct - on - line) made from 16 G. CRCA

sheet duly epoxy powder painted inside and outside with

hinged doors and locking, arrangement consisting of

suitable size of ON- OFF isolator (AC - 3/23duty) main

fuses, single phasing preventer, indicating lamps for R- Y -

B phases, overload relay, Automatic water level

controller, Ammeter, Voltmeter each with two way

main contactor & overload relay, start - stop push

buttons, to be erected on angle iron frame grouted on

wall as directed. The isolator, overload relay &

contactors will be of L & T, Siemens or BCH make only.

(A) DOL up to 5.0 H.P.

190 Providing and erecting ISI marked PVC insulated PVC 30.00 Mtr 146.45

Sheathed Flat flexible Submersible copper cable

approved make of following Size. (C) 3 Core x 4 Sq. mm

191 Providing Water proof straight Joint in PVC insulated flat 2.00 Nos. 189.88

flexible copper cable by using insulating material, water

proofing material, & making the joint complete. (A) Up to

192 Supplying & erecting 5 stage single reverse osmosis 1.00 Nos. 15620.66

water purification system with M.S. powder coated

frame, prefilter housing with 'O' ring presediment filter

GAC filter, carbon filter suitable buster DC pump capacity

80 psi, mention with 40 psi inline type post carbon filter

auto low & high pressure switches with following size of

storage tank & LPH capacity & erected as directed [B]

Ltr / Hr with 30 Ltr. Storage Tank

Item Rate In

Description of Item Quantity Unit Amount

No figures

193 Supply, Installation, Testing & Commissioning of 1.50 PER KW 46187.00

following size of Grid Tied Solar Power Plant with

Solar Panels (ALMM approved): Frame Material :

Anodized Aluminum alloy Frame With Twin Wall Profile,

Front Cover : High Transmission Low-Iron Tempered

Glass (AR Coated), High efficency and positive power

tolerance Pmax: 0/+5, Module Efficiency should be

approx. 19.5%-22%, Normal operating temperature

45'C, Junction Box with Waterproof IP67 & MC4

Compatible and Enclosed with Bypass diodes, 100%

Electroluminescence test to ensure error free Modules,

Thep. temp. co-efficient of the PV module shall equal or

better than -0.45%/degree C. Solar PV modules of

minimum fill factor 75% to be used. Unit Production:-

More than 4.5 Unit /kw /day (Actual)(1Year Avg) With

10 year Product warranty. Modules must be complied to

the DCR(Domestic content requirements). The Ration of

AC to DC is 5:6 for the Installation capacity which are

given in AC KW.

Solar Inverter: MPPT Range: MPPT Range: 80-1000 V

Max efficiency: 97.5% - 98.9%, O/p Frequency: 50/60Hz,

Operating Altitude (m) ≤4000, O/p Power Factor: ~1,

O/P THDi: <3%, Operating Tempreture Range: -25~60°C,

Integrated protection of Inverter are Anti-islanding

Protection, Input Reverse Polarity Protection, Insulation

Resistor Detection, Ground fault protection, Residual

Current Monitoring Unit, Output Over Current Protection,

Output Short Circuit Protection, Output Over Voltage

Protection, PV array string fault Protection. Protection

Item Rate In

Description of Item Quantity Unit Amount

No figures

Integrated, Input Reverse Polarity Protection Integrated,

Insulation Resistor Detection Integrated, Residual

Current Monitoring Unit Integrated, Output Over Current

Protection Integrated, Output Short Circuit Protection

Integrated, Output Over Voltage Protection Integrated,

Protection Degree: IP65, User Interface LCD &

APP,Datalogger & Communication: GPRS / Wi-Fi, Module

Mounting Structure: The mounting (Rectangular pipe /

square pipe / circular pipe) with requisite cross bars,

nuts and bolts, etc. shall be Hot deep galvanized with

minimum 80micron coating. The Rectangular / square

/circular hollow pipe section used for the structure

should have a minimum thickness of 2.0 mm. other than

above, the material thickness should be minimum

mm. A certificate of a structural engineer certifying the

strength and stability of the mounting structure to

withstand the weight and wind speed of 150 km/hour

shall be submitted by the vendors. Hot Dipped

Galvanized steel coils. suitable arrangement for base

plate for foundation , solar panel mounting, the structure

should be suitable for carry the load of solar

panel,wiring, sprinkler system etc. with necessary

foundation work/wall mount, j bolt, anchor fastner etc.

the nut bolt used for installtion of stucture should be (SS

304) quality.The ground clearance of the bottom most

edge of solar panel shall not be less than 300 mm to

mm or as per site’s technical/feasibility requirement.

a. Column –The minimum section (thickness) should be

Total Rs.

I/We am/are willing to carry out the work at………………….% above/below percent(Should be written in figures and

words) of the estimated rate mentioned above. Amount of my /our

Tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

Item Rate In

Description of Item Quantity Unit Amount

No figures

The Contractor shall exhibit a board with detailed specification and details of work as directed by the

1 Engineer-In-Charge for which no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 Income tax TDS will be deducted at a source while making payments of bills

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where

4 there is a change as per actual mix design the cost of difference of cement consumption have been deducted

from the rate of original item at the rate of input rate mentioned in all the tender.

Deputy Executive Engineer Executive Engineer

Ankleshwar ( R & B ) Sub Division Bharuch ( R & B ) Division

Ankleshwar Bharuch