Repair and maintenance and improvement of external water supply system at Birpur and Ghanghora Area under GE Dehradun

Amount

M&L for excavation in trenches in any type of soil not exceeding 1.5 Meter wide and not exceeding 1.5 Meter deep in any type of soil including cutting in slopes etc for laying of pipe line including getting out, complete all as specified and directed.

M&L for returning, filling in, including spreading, leveling, watering and well ramming in layers in soft / loose soil not exceeding 25 cm in each layer complete all as specified and directed by Engineer-in-Charge.

M&L for removal of excavated material (Soil) to a distance up to 50 Meter from starting point and depositing where directed at level not exceeding 1.5 Meter above as directed by Engineer-in-Charge.

M&L for dismantling electrically and taking down unserviceable fully automatic starter any type dry/ ATS type, from base frame and transporting to workshop for cleaning and refixing the serviceable parts back after repair and replacement of U/s parts for the 12.5 HP to 20 HP capacity size.(Note: Spare parts required for replacement shall be measured & paid for separately under respective item).

M&L for dismantling electrically and taking down unserviceable fully automatic starter any type dry/ ATS type, from base frame and transporting to workshop for cleaning and refixing the serviceable parts back after repair and replacement of U/s parts for the 50.0 HP to 80.0 HP capacity size.(Note: Spare parts required for replacement shall be measured & paid for separately under respective item).

Supply only following spare parts and shall be replaced for starter under item No 4 & 5 here in above (Parts of starter shall be as per the make of starter.)

Fixed power copper contacts suitable for 60 HP star delta starter.

Fixed power copper contacts suitable for 75 HP star delta starter.

Moving power copper contacts suitable for 60 HP star delta starter.

Moving power copper contacts suitable for 75 HP star delta starter.

Auxiliary switch type -01 with 1 No-1 NC suitable for 60/80 HP star delta starter.

RZ timer with coil & time delay range 3-12 seconds suitable for 60/80 HP starter.

Mini motor Protection relay protections for Thermal overload, Earth fault, Locked rotor, single phasing, current unbalance, phase sequence reversal and under current. Make L&T

Three pole power contactor suitable for star delta starter 12.5 HP to 20 HP.

S&F in repair fully automatic Star Delta starters with D range Contractor, LR1D OLR & Electronic Star Delta Timer wall mounted type with start/stop push bottom, with enclosure for 75 HP capacity complete all as specified and directed. Make:- C&S/BCH/L&T.

Dismantling and taking out the existing corroded / scaled GI pipe / PPR/ PALP pipe with fittings connections from trenches, walls, ceiling or floor and removal from site or disposed off for the following sizes complete all as specifed and directed. Note: Excavation and earth work shall be measured and paid seperately under respective item of schedule "A"

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

Supply, Laying, fixing & testing galvanised iron water tubing 'medium grade; ISI marked with and inclduing all GI fittings such as flanges, unions reducers sockets, socket reducing bends, elbows, tee, checkneuts, caps, plugs etc laid in trenches for the following sizes complete all as specifed and directed. Note: Excavation and earth work shall be measured and paid seperately under respective item of schedule "A"

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

M&L for mild steel framed work such as grills, gratings, gratings for water channels, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work mild steel conforming to Fe - 290, Gde- E 165 complete all as specified and directed.

M&L for structural steel framed work as in valve pit covers of angle or other section with , rails, braces, etc., complete drilled for fixing of steel sheeting or other covering, to be prepared for hanging with and including either hooks and hinges or steel hanging fittings and fixing including removing unserviceable cover complete (structural steel conform to Fe 410w (Gde & 250) quality 'A') all as specified and directed.

M&L for 3 mm thick mild steel plain black sheet in covering to valve pit frames and the like cut to size edges as directed, holes punched, including welded to frame complete all as specified and directed by Engr-in-Charge.

Dismantling/taking out defective Gun metal gate valve and S&F for Gun metal gate valve with iron wheel head by screwing/cutting of existing pipe lines for the following size complete all as specifed and directed. Make: Sant / Seiko

20 mm bore

25 mm bore

40 mm bore

50 mm bore

M&L for construction of brick masonary valve pit of size 60cm x 60cm x 60cm (internal demension) complete with 50x50x6mm angle iron frame, with 3.15mm thick MS cover sheet with hinges, sliding type lifting handle of MS bar 12 mm dia with locking arrangement heavy duty duly welded with angle iron frame complete including necessary excavation and earth work, PCC (1:2:4,) type B-0 (using 12.5mm graded agregate) as in coping, 15mm thick internal plaster in CM (1:4) 75mm thick PCC (1:4:8), type D-2 (using 40mm graded agregate)lean concrete over 75mm thick hard core over rammed earth, flooring shall be 40mm thick PCC (1:2:4) type B-1(using 20mm graded agregate) all steel surfaces shall be painted with two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specifed and shown on drawing No TD/EM/12 complete all as specfied and directed.

M&L for construction of brick masonary valve pit of size 90cm x 90cm x 90cm (internal demension) complete with 50x50x6mm angle iron frame, with 3.15mm thick MS cover sheet with hinges, sliding type lifting handle of MS bar 12 mm dia with locking arrangement heavy duty duly welded with angle iron frame complete including necessary excavation and earth work, PCC (1:2:4,) type B-0 (using 12.5mm graded agregate) as in coping, 15mm thick internal plaster in CM (1:4) 75mm thick PCC (1:4:8), type D-2 (using 40mm graded agregate)lean concrete over 75mm thick hard core over rammed earth, flooring shall be 40mm thick PCC (1:2:4) type B-1(using 20mm graded agregate) all steel surfaces shall be painted with two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specifed and shown on drawing No TD/EM/12 complete all as specfied and directed.

M&L for construction of brick masonary valve pit of size 120cm x 120cm x 90cm (internal demension) complete with 50x50x6mm angle iron frame, with 3.15mm thick MS cover sheet with hinges, sliding type lifting handle of MS bar 12 mm dia with locking arrangement heavy duty duly welded with angle iron frame complete including necessary excavation and earth work, PCC (1:2:4,) type B-0 (using 12.5mm graded agregate) as in coping, 15mm thick internal plaster in CM (1:4) 75mm thick PCC (1:4:8), type D-2 (using 40mm graded agregate)lean concrete over 75mm thick hard core over rammed earth, flooring shall be 40mm thick PCC (1:2:4) type B-1(using 20mm graded agregate) all steel surfaces shall be painted with two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specifed and shown on drawing No TD/EM/12 complete all as specfied and directed.

S&F in repair CI sluice valve both end flanged dully drilled for both ends with stainless steel spindle and nuts stuffing box etc type PN - 1.6, ISI marked of following sizes:-

250 mm bore

200 mm bore

150 mm bore

100 mm bore

80 mm bore.

S&F in repair CI Non return valve flanged ends as per IS-5312 complete with Nuts/Bolts and washers and rubber packing etc for the following sizes:-

200 mm bore

150 mm bore

100 mm bore

80 mm bore

S&F in repair CI foot valve, One end flanged and strainer to the other side for the following sizes:-

80 mm bore

100 mm bore

150 mm bore

200 mm bore

S&F in repair water pressure gauge glycerin filled of size 100 mm 0-7 kg/cm2 complete all as specified & directed.

Taking down old U/S ampere meter from existing panel board and M&L for new ampere meter 144x144 mm for three phase AC supply with complete wiring connections all as directed. Make :- L&T : WL131010OOOO or equivalent of Legrand/Seimens/C&S/Schenider.

Taking down old U/S volt meter from existing panel board and M&L for new volt meter 0-500 volt for three phase AC supply with complete wiring connections all as directed. Make :- L&T :WL411010OOOO or equivalent of Legrand/Seimens/C&S/Schenider.

Taking down old U/S multifunction meter 3 phase from existing panel board and M&L for new multi function meter for three phase AC supply for voltage / ampere / power factor with complete wiring connections all as directed. Make :- L&T : MFM 4410 or equivalent of Legrand/Seimens/C&S/Schenider.

Supply Installation Testing and Commissioning of SS Probe unit of suitable length up to 6 M depth of tanks. The probe shall have continuous magnetic reed sensors with resolution of 10 mm, with 0-5000 ohms resistance to act as potentiometer. The sensors to be actuated by a single actuating float to give analog output based on level at any stage including taking down existing unserviceable unit complete all as specified & directed.Make Active Controls Model No FLIC 500 or equivalent as approved by GE

Supply Installation of digital Indicator unit, with Jumbo 5 digit red LED 7 segment display of 100 mm each, to be connected with the probe unit. The unit shall have high and low alarm to be set according to requirement based on levels indicated. It should be possible to calibrate the Indicator to display in percentage or liters, centimeters as required, signaling distance 300mtrs, power cosumption 0.25W including taking down existing unserviceable unit complete all as specified and directed. Make : Active Controls or equivalent as approved by GE

Supply and fixing 2 core twisted flexiable weather proof cable PVC insulated and unsheathed multistranded copper conductor of size 1.5 sq mm including taking out old unserviceable cable complete all as specified & directed

Material and labour for restoration of water supply by identifying and rectifying the water supply leakage, repair work, at any location, in any type of leakage in 15mm/ 20mm/25mm pipes of GI/ MS with any type of joints i.e. flanged, socketed,welding joint, including required fittings such as socket/ union/ long screw/ nipple, by cutting/ threading as required at site and as directed. (Note : (i) Any earth work required for repair shall be measured and paid for separately. (ii) Any material required for leak repair deemed to be included in the above quoted rate. (iii) Any length of pipe required shall be paid sepertately under relevant item).

Material and labour for restoration of water supply by identifying and rectifying the water supply leakage repair work, at any location, in any type of leakage in 40mm / 50mm/ 80mm/pipes of CI/ GI/DI/MS with any type of joints i.e. flanged, socketed, tyton rubber ring, welding or lead joint including required fittings such as socket/ union/ long screw/ nipple, by cutting/ threading as required at site , chocking of lead with spun yarn or providing new gasket / rubber ring/ nut bolts/ required welding work as per site requirement complete all as specified and as directed. (Note : (i) Any earth work required for repair shall be measured and paid for separately. (ii) Any material required for leak repair deemed to be included in the above quoted rate. (iii) Any length of pipe required shall be paid sepertately under relevant item)

Material and labour for restoration of water supply by identifying and rectifying the water supply leakage repair work, at any location, in any type of leakage in 100mm / 150mm pipes of CI/ GI/DI/MS with any type of joints i.e. flanged, socketed, tyton rubber ring, welding or lead joint including required fittings such as socket/ union/ long screw/ nipple, by cutting/ threading as required at site , chocking of lead with spun yarn or providing new gasket / rubber ring/ nut bolts/ required welding work as per site requirement complete all as specified and as directed. (Note : (i) Any earth work required for repair shall be measured and paid for separately. (ii) Any material required for leak repair deemed to be included in the above quoted rate. (iii) Any length of pipe required shall be paid sepertately under relevant item).

Material and labour for resoration of water supply by identifying and rectifying the water supply leakage repair work, at any location, in any type of leakage in 200mm / 250mm pipes of CI/ GI/DI/MS with any type of joints i.e. flanged, socketed, tyton rubber ring, welding or lead joint including required fittings such as socket/ union/ long screw/ nipple, by cutting/ threading as required at site , chocking of lead with spun yarn or providing new gasket / rubber ring/ nut bolts/ required welding work as per site requirement complete all as specified and as directed. Note : (i) Any earth work required for repair shall be measured and paid for separately.(ii) Any material required for leak repair deemed to be included in the above quoted rate.(iii) Any length of pipe required shall be paid sepertately under relevant item.

Material and labour for resoration of water supply by identifying and rectifying the water supply leakage repair work, at any location, in any type of leakage in 300mm pipes of CI/ GI/DI/MS with any type of joints i.e. flanged, socketed, tyton rubber ring, welding or lead joint including required fittings such as socket/ union/ long screw/ nipple, by cutting/ threading as required at site , chocking of lead with spun yarn or providing new gasket / rubber ring/ nut bolts/ required welding work as per site requirement complete all as specified and as directed. (Note : (i) Any earth work required for repair shall be measured and paid for separately. (ii) Any material required for leak repair deemed to be included in the above quoted rate. (iii) Any length of pipe required shall be paid sepertately under relevant item).

Disconnecting and taking down unserviceable electric motor of capacity 75 HP 1450 RPM 3 Phase from base frame and shifting to workshop for rewinding, opening complete, taking out Rotor assembly from stator carefully and cutting/cleaning burnt winding wire from stator, carefully repairs to damaged slots including Rewinding of stator with super enameled copper wire of gauge same as original & Varnishing the same, drying tapping with cotton tapes, all electrical connections should be soldered properly, reassembling reshifting & reinstallation at site inclduing testing at full load complete all as specifed & directed.

All as per item No. 33.00 here in above but 20 HP 1480 RPM 3 Phase complete all as specified & directed.

All as per item No. 33.00 here in above but 15 HP 1480 RPM 3 Phase complete all as specified & directed.

All as per item No. 33.00 here in above but 12.5 HP 1480 RPM 3 Phase complete all as specified & directed.

All as per item No. 33.00 here in above but 10 HP 1480 RPM 3 Phase complete all as specified & directed.

Taking down centrifugal pumping set of discharge-1500LPM at 130 Mtr head, 75 HP, from base frame including disconnection of inlet suction and discharge pipe line, pump coupling and shifting to workshop for repair, opening dismantling and overhauling complete parts, cleaning all parts by Kerosene oil neatly including replacement of defective spare parts by news parts necessary welding machine/ grinding work if required at the time of refitting of spare into pump set, re-shifting & reinstallation the pump set on base frame with proper alignment with motor and testing on full discharge complete all as specified and directed. (Note:- (i) Spare parts which are required to be replaced during repair shall be measured and paid separately as supply only rate. Fixing element shall be deemed to be included in the quoted rates of ibid item. (ii) Contractor shall ensure water pipe lines sealed by blocking with dead flange for the repair period if required).

Supply only following spare parts to be replaced for repairing the pump set under item No. 38 above

CI impeller

Pump shaft SS EN-8 complete with all machining work.

CI sleeve

CI bush

MS coupling complete with rubber tyre/ Star rubber bush. make:- Love Joy/ Unic/ Unimax/ Unique/ Gemini

CI neck ring

Ball bearing

Gasket packing set

Pump stud of stainless steel with nut

Taking down centrifugal pumping set of discharge-10000 GPH at 40 Mtr head, 20 HP, from base frame including disconnection of inlet suction and discharge pipe line, pump coupling and shifting to workshop for repair, opening dismantling and overhauling complete parts, cleaning all parts by Kerosene oil neatly including replacement of defective spare parts by news parts necessary welding machine/ grinding work if required at the time of refitting of spare into pump set, re-shifting & reinstallation the pump set on base frame with proper alignment with motor and testing on full discharge complete all as specified and directed. (Note:- (i) Spare parts which are required to be replaced during repair shall be measured and paid separately as supply only rate. Fixing element shall be deemed to be included in the quoted rates of ibid item. (ii) Contractor shall ensure water pipe lines sealed by blocking with dead flange for the repair period if required).

Supply only following spare parts to be replaced for repairing the pump set under item No. 40 above

CI impeller

Pump shaft SS EN-8 complete with all machining work.

CI sleeve

CI bush

MS coupling complete with rubber tyre/ Star rubber bush. make:- Love Joy/ Unic/ Unimax/ Unique/ Gemini

CI neck ring

Ball bearing

Gasket packing set

Pump stud of stainless steel with nut

Taking down centrifugal pumping set of discharge-42 to 72 cum/hr at 44 to 50 Mtr head, 10/12.5 HP multistage, from base frame including disconnection of inlet suction and discharge pipe line, pump coupling and shifting to workshop for repair, opening dismantling and overhauling complete parts, cleaning all parts by Kerosene oil neatly including replacement of defective spare parts by news parts necessary welding machine/ grinding work if required at the time of refitting of spare into pump set, re-shifting & reinstallation the pump set on base frame with proper alignment with motor and testing on full discharge complete all as specified and directed. (Note:- (i) Spare parts which are required to be replaced during repair shall be measured and paid separately as supply only rate. Fixing element shall be deemed to be included in the quoted rates of ibid item. (ii) Contractor shall ensure water pipe lines sealed by blocking with dead flange for the repair period if required).

Supply only following spare parts to be replaced for repairing the pump set under item No.42 above

CI impeller

Pump shaft SS EN-8 complete with all machining work.

CI sleeve

CI bush

MS coupling complete with rubber tyre/ Star rubber bush. make:- Love Joy/ Unic/ Unimax/ Unique/ Gemini

CI neck ring

Ball bearing

Gasket packing set

Pump stud of stainless steel with nut

Taking down centrifugal pumping set of discharge-10000 GPH at 40 Mtr head, 15 HP multistage, from base frame including disconnection of inlet suction and discharge pipe line, pump coupling and shifting to workshop for repair, opening dismantling and overhauling complete parts, cleaning all parts by Kerosene oil neatly including replacement of defective spare parts by news parts necessary welding machine/ grinding work if required at the time of refitting of spare into pump set, re-shifting & reinstallation the pump set on base frame with proper alignment with motor and testing on full discharge complete all as specified and directed. (Note:- (i) Spare parts which are required to be replaced during repair shall be measured and paid separately as supply only rate. Fixing element shall be deemed to be included in the quoted rates of ibid item. (ii) Contractor shall ensure water pipe lines sealed by blocking with dead flange for the repair period if required).

Supply only following spare parts to be replaced for repairing the pump set under item No. 44 above

CI impeller

Pump shaft SS EN-8 complete with all machining work.

CI sleeve

CI bush

MS coupling complete with rubber tyre/ Star rubber bush. make:- Love Joy/ Unic/ Unimax/ Unique/ Gemini

CI neck ring

Ball bearing

Gasket packing set

Pump stud of stainless steel with nut

Material and labour for cutting of metelled road for taking out old or laying of new pipe appx 35cm wide and 75 cm deep and making good surface to the existing specification complete all as specified and directed.

S&F in repair MCCB 500 Amps 35 KA 4 pole 415 V AC 50 Hz complete all as specified and directed. Make: Lexic Legrand (DPX)/ Schneider NSX/ L&T D sine/Simens 3 VL

S&F in repair MCCB 400 Amps 35 KA 4 pole 415 V AC 50 Hz complete all as specified and directed. Make: Lexic Legrand (DPX)/ Schneider NSX/ L&T D sine/Simens 3 VL

S&F in repair MCCB 250 Amps 35 KA 4 pole 415 V AC 50 Hz complete all as specified and directed. Make: Lexic Legrand (DPX)/ Schneider NSX/ L&T D sine/Simens 3 VL

S&F in repair MCCB 200 Amps 35 KA 4 pole 415 V AC 50 Hz complete all as specified and directed. Make: Lexic Legrand (DPX)/ Schneider NSX/ L&T D sine/Simens 3 VL

S&F in repair MCCB 160 Amps 25 KA 4 pole 415 V AC 50 Hz complete all as specified and directed. Make: Lexic Legrand (DPX)/ Schneider NSX/ L&T D sine/Simens 3 VL

S&F in repair MCCB 63 Amps 16 KA 4 pole 415 V AC 50 Hz complete all as specified and directed. Make: Lexic Legrand (DPX)/ Schneider NSX/ L&T D sine/Simens 3 VL

Taking down pumping set from base frame including disconnection from coupling type DSM 65/328 (Make: Kirloskar) of discharge capacity 10000 GPH at 40 mtr head, installed at pump house and shifting to workshop for repair, opening dismantling and overhauling complete parts, cleaning all parts by Kerosene oil neatly and Supply and fixing new rotary assembly complete with CI impellers ,SS shaft , sleeves , bushings , bearing housing, neck ring, center ring, keys for shaft, keys for coupling, gland packing, any nut bolt washer required or any other spare of standard assembly set of OEM, incl necessary welding, machining, grinding work if required at the time of refitting of assembly into pump casing, and refixing of the on base plate with proper alignment with motor and testing on full discharge complete all as specified and directed . Note:- (i) The item rate shall be deemed to be inclusive of required spares, any machining work, transporting of pump set to and fro workshop if required and back after repair. (ii) Contractor shall ensure water pipe lines sealed by blocking with dead flange for the repair period if required).

M&L for MS clamps fabricated from MS flat not less than 4mm thick fixed to water supply pipes to stop the leakage with rubber packing, nut , bolts washers, cutting, welding etc as required at site and all as directed.

S&F in replacement cast iron 'D' joint set for 200 mm bore CI/DI pipe complete of two flanged collar one no sleeve two nos rubber 'O' ring and nut bolts washers of suitable size complete including necessary cutting, grinding work to fix in pipe as directed. (Note:- Earth work required to clear the pipe shall be measured and paid separately)

S&F in replacement cast iron 'D' joint set for 150 mm bore CI/DI pipe complete of two flanged collar one no sleeve two nos rubber 'O' ring and nut bolts washers of suitable size complete including necessary cutting, grinding work to fix in pipe as directed. (Note:- Earth work required to clear the pipe shall be measured and paid separately)

S&F in replacement cast iron 'D' joint set for 100 mm bore CI/DI pipe complete of two flanged collar one no sleeve two nos rubber 'O' ring and nut bolts washers of suitable size complete including necessary cutting, grinding work to fix in pipe as directed. (Note:- Earth work required to clear the pipe shall be measured and paid separately)

S&F in replacement cast iron 'D' joint set for 80 mm bore CI/DI pipe complete of two flanged collar one no sleeve two nos rubber 'O' ring and nut bolts washers of suitable size complete including necessary cutting, grinding work to fix in pipe as directed. (Note:- Earth work required to clear the pipe shall be measured and paid separately)

Taking down carefully copper/Aluminum point wiring (light, fan socket and power) complete including switches, ceiling rose lamp holder and regulator etc and removing from site and making good disturbed surfaces of walls/floors etc complete all as specified and directed by Eng-in-charge.

M&L for point wiring with 1.5 Sqmm (nominal area) two single core PVC insulated unsheathed multi stranded copper conductor cable 1100 volts grade, FRLS grade in concealed PVC conduit 20 mm dia or higher size and with suitable size of sunk type pressed steel terminal box 1.2mm thick, duly painted for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, including contineous earth wire PVC insulated, unsheathed, multi stranded copper conductor cable 1.5 sqmm (nominal area) FRLS grade, green colour, up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of the following. (Note: Colour code shall be maintained as per IE rule).

(a) One light point point /bell buzzer point controlled by one-one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

All as per item No 60.00 here in above but one 3 pin socket outlet 15 Amp independent, with cable 2.5 Sq mm size, with earth continuity coductor of size 2.5 Sq mm.

S&F switch piano flush, button type 5 Amp SP 250 V AC complete all as specified & directed.Make : Anchor/Havells

S&F switch piano flush button type 15 Amps SP 250 V AC complete all as specified & directed.

S&F socket outlet multipurpose 3 Pin 5 Amp and 2 Pin 5 Amps 250 V AC complete all as specified & directed.

S&F socket outlet two in one three pin 5 Amp and 15 Amp 2 module 120 W flush type complete al as specified.

S&F stepped type electronic fan regulator flush type two module 400 Watt on the existing phenolic laminated sheet etc as required.

S&F ceiling rose, 3 terminal/PVC/polycarbonate, isolated body 250 V AC.

S&F lamp holder PVC/polycarbonate type with back plate suitable for batten fittings.250 V AC.

S&F in replacement sheet metal enclosures 240 volt with suitable rated bus bar for double door 8 way IP-43DB's lk-09suitable for one MCB SPN as incoming and 6 MCB SP as out going, mounting flush on wall and making good disturbed surfaces complete all as specified and directed by Engr-in-charge . (MCBs shall be measured and paid separately)

S&F MCB double pole 240 Volt 10 KA 40 Amp 'B' series conforming to ISI marked complete all as specified & directed.

S&F MCB single pole and 240 volt 10 KA 5-32 Amp 'B' series conforming to ISI marked all as specified and directed.

S&F in replacement wall mounted tube light fitting 1x18/20/22 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 6500K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed. Make: Philips cat part No TMC 501P1xT LED 22WP-3241(Tube Batten) and MAS LE$D 1200mm 18W-865-T-81 (Tube) / Wipro Cat part No W10921208 (Tube Batten) L213-181-655E (Tube)/ Havells Cat Part No LHFYBYPNIAIW022 (Tube Batten) LHLDCL X EUL 83020 (Tube).

S&F in repair LED light fitting 1x10 w bulk head fitting complete with accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed.

Supply, Fixing in replacement and testing 32 Watt LED down lighter recessed mounted 2x2 feet ultra modern designed LED luminaire which provide soft light and glair free symmetrical illumination suitable for grid ceiling and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 complete all as specified and directed. Make:- Philips: RC380B LED 36S-6500PSUOD or equivelent make of Havells/ CROMPTON.

M&L for Painting of ceiling fans complete of any sweep in situ with synthetic enemel paint by spraying including filling cavities with filler one coat after cleaning solution dust/oil/dirt etc including writing MES No complete all as specified and directed

Disconnecting electric connection and taking down of ceiling fan / Exhaust fan of any sweep complete carefully for overhauling, removing capacitor, split pins checking of bearings/bush, cleaning the fan blades with cleaning solution, replacing the unserviceable bearing, bush, capacitor , safety split pin and nuts, bolts, washer etc, cutting threading down rod if required, reassembling the ceiling fan complete after greasing/servicing, oiling testing the same making the fan in serviceable condition and refixing/ hanging the same complete all as specified and directed by Engineer-in-Charge (Note: Bush, bearing, capacitor, down rod, hanging clamps, will be paid under relevant item of this Schedule). Cost of split pins, nut bolts and threading of down rod pipe rates are included in quoted rate)

Rewinding of ceiling fan of 1200 mm 1400mm sweep with super enamalled copper wire of same gauge as per existing including varnishing, drying, paper insulation material complete complete all as specified and directed

Supply and replace ball bearing No. 6201/6202/6203/6204 for 1200/1400mm sweep ceiling fans & 300/350/450mm sweep exhaust fans as required at site complete all as specified and directed. Make:- SKF/TATA/NBC.

Supply only GM bush bearing for 1200/1400 mm sweep ceiling fan as required at site.complete all as specified and directed

Supply only heavy duty rubber insulator for 1200/1400 mm sweep for hanging ceiling fan.complete all as specified and directed

Supply only fan capacitor 2.5 mfd make universal / Asian/Epcos .complete all as specified and directed

Supply only white flexible wire three core 23/0066 with copper multistranded conductor PVC insulated (BC cotton) complete all as specified and directed.

Supply only PVC canopy suitable for ceiling fan 1200/1400 as per requirement at site complete down and upside all as specified and directed.

M&L for earthing complete with using galvanized mild steel earth plate (electrode) 600 mm x 600 mmx 6 mm thick buried directly in ground, earth pit not less than 2.25 mtr deep below ground level with top edge of the earth plate not less than 1.50 m below ground level and earth plate surrounded with adequate quantity of charcoal dust mixed with salt to be packed thickness of 15 cm all round the plate using 4 mm dia GI earth lead wire as earth lead moulded and rivetted to earth plate at one end and connected to main equipment at switch/control board at another end, GI earth lead protected in and including 15 mm dia GI ‘medium grade’ pipe from upper end of earth plate upto equipment with & including 20 mm dia bore GI pipe ‘medium grade’ as water pipe from earth chamber to upper edge of the earth plate, GI funnel with wire mesh fixed on water pipe and provision of PCC 1:2:4 type B1(using 20 mm graded stone agg) as in pits chamber and RCC pit cover 50 mm thick of precast RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as per electrical plate No.3 of SSR Part-II 2010 and testing on completion all as specified and directed.

Note: (i) If the earth resistance is not found within permissible limit, earthing shall be redone by contractor at no extra cost. (ii) Cost of GI wire 4 sqmm and 15 mm dia pipe medium grade upto 7.5 mtr is included in the rate quoted for this item

M&L for painting of different sizes connecting pipes Valve pit chamber covers, rolling shutters and its related items including writing letters on pump motors etc at various installations as per colour code with one coat of primer and two coat of synthetic enamelled paint all as specified and directed

Supply and fixing flood light fittings, energy saving environmental friendly, long life, exclusive innovative epoxy powder coated die-cast aluminium housing IP65 flood light with high power LED's as light sources, suitable for high lighting architectural features or retail spaces as 70/80 watt LED with lumen output 12500, system efficiency 100 lumen/watt, CCT>5700K, PF>0.95, Glass cover complete all as specified and directed. Make:- Philips cat No. BVP120 LED70 CWNB FG S1 PSU GR/Havells cat part No. LHEUACN7PN6K080/ CG cat part No LSFO-90-CDL including taking down old flood light fittings

S&F sheet metal enclosure with IP 65 IK09 protection, 240V 3 phase, front door, weather proof, out door type with and including electro-mechanical street light timer , 3 module time switch (ABB CAT No AT3-R or equivalent of L&T/C&S), MCB 40 Amp SP, power contactor 40A, luxo switch 1 Lux =1,000,00 auto manual faclity with complete wiring suitable for 15 KW 3 phase 6 module including GI clamping & fixing to pole all as directed. Make: (ABB or equivalent of L&T/C&S)

Supply and fixing 3 core twisted flexiable weather proof cable PVC insulated and unsheathed multistranded copper conductor of size 2.5 sq mm including taking out old unserviceable cable complete all as specified & directed

Supply and Fixing Integral LED Street Light Luminaire comprising of pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 70/72 watt with efficiency 100 lumen/watt at system level, CCT>5700K, with average life class 50,000 burning hours, complete all as specified and directed.. Make:- Philips model No. BRP410LEDCW072MRFGSIPSUGR Havells model No. LHETBXU7PA6J070 and syska cat No- SSK-ST 60W including taking out old unserviceable street light.

Supply and Fixing Integral LED Street Light Luminaire comprising of pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 45 watt with efficiency 100 lumen/watt at system level, CCT>5700K, with average life class 50,000 burning hours, complete all as specified and directed.. Make:- Philips model No. BRP410LEDCW045MRFGSIPSUGR Havells model No. LHETAXU7PN6J045 and syska cat No- SSK-ST 45W including taking out old unserviceable street light.

S&F Street light bracket made out of 40 mm dia medium grade GI pipe not less than 1.5 length, bend to shape including 2 Nos, 50 x 6 mm GI Clamps nut, bolts washer, reducer of required suitable for above size for fitting etc complete including necessary painting with two coats of synthetic enamel paint over a coat of primer to ms clamp complete all as specified and directed including taking out old unserviceable bracket.

S&F pole mounted Junction Box of size 250X200X105mm for fixing cable with provision of four Nos copper busbar with hole for incoming and outgoing cable, busbar of capacity 100 Amp mounted on epoxy insulator with provision of MCB SP 6 Amp 'B' series including all bare conductor of cable duly insulated PVC heat shrinkable sleeve 1.1 KV heavy duty grade cp brass cable glands & lugs for incoming & outgoing connection including taking out old unserviceable junction box all as directed. Make: Sintex Cat No.GS-JB-2520 or equivalent of Hensel/ Schneider

M&L for preparation of old painted steel surfaces of LT poles and applying two coats of aluminium heat resistance paint approx 6 mtr height on outer surfaces of pole from 1.5 m above the coping/ground level up to the top of steel poles including painting MS cross arms, clamps, nuts and bolts etc and painting alternative black and white strips of 30 cm height with two coats of synthetic enamel paint upto 1.5 mtr height from the ground/coping level including pole numbering/marking complete all as specified and as directed.

Fixing only Aviation lamp for over head reservoir 21 mtr stagging all as directed. (Lamp shall be issued from MES store)

S & F 4 core twisted flexiable weather proof cable PVC insulated and unsheathed multistranded copper conductor of size 2.5 sq mm for aviation light at over head tank fixed with saddles along the columns all as directed.

M & L for CI fitting for spigot & socket end pipes such as Bends (any type, radius and angle), Tapers any type (Straight, bend, increasing, decreasing or double socket etc), Tee pieces single branch, `Y` junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs and mechanical joints any type etc upto 150 mm bore including removing/ dismantling of old CI fittings complete all as specified and directed.

Cutting of cast iron pipe mains 150 mm bore for insertion of tees, collars, sluice valves, etc including dewatering work required for working water pipe lines complete all as specified and directed.

All as per item No 97.00 here in above but 100 mm bore.

All as per item No 97.00 here in above but 80 mm bore.

Taking up or down cast iron pipe of tyton joint type from trenches including dismentling tyton joints type & removing for disposal for the pipes of 150 mm bore complete all as specified and directed. (Note: Excavation and earth work shall be measured and paid seperately under respective item of schedule "A")

All as per item No 100.00 here in above but 100 mm bore.

All as per item No 100.00 here in above but 80 mm bore.

Supplying and laying in trenches CI spun pipe 150 mm bore, centrifugally cast, with spigot and socket end, class LA ISI marked of the following bores complete all as specified and directed. (Note: Excavation and earth work shall be measured and paid seperately under respective item of schedule "A"). Make : Electrosteel/TATA

All as per item No 103.00 here in above but 100 mm bore.

All as per item No 103.00 here in above but 80 mm bore.

M&L for tyton rubber gasket joints for 150 mm bore complete all as specified and directed

M&L for tyton rubber gasket joints for 100 mm bore complete all as specified and directed

M&L for tyton rubber gasket joints for 80 mm bore complete all as specified and directed

Material and labour for servicing of DG set of any make by cleaning, servicing, oiling and greasing of moving parts, checking the serviceability of self starter, alternator, AVR for proper voltage out put, batteries voltage & electrolyte be checked & added upto top level, functunability of safety devices, all nut - bolts of Engine and alternator, proper tension of fan belts, check coolant level and top up if necessary. Ensuring leak proof of all type i.e. hose for water, pipe line of fuel and lub oil etc., Checking of air cleaner element & cleaning with dry compressed air (60 psi pressure.), replacement of lubricating oil (Cost of lubricating oil shall be measured and paid separately) including 'Material and labour for replacement of Air filter elements set, Cleaning of oil bath type filters and replacement of oil of oil bath filter, Lubricating oil filters element complete set, Fuel filters element, By pass filter, Corrosion resistor plate, Fan belts complete as specified and directed for following capacity. (Note : servicing will be done through authorised dealer only and a certificate to this effect will be submitted from authorised dealer to the department.)

NOTES: (i) The quoted rates of the contractor includes for fixing the serviceable parts in position and replacement of unserviceable parts with new parts. The cost of servicing of DG set are inclusive of replacement of small/minor parts such as nuts, bolts, washers, locking nuts, small springs, studs etc and parts mentioned in the item above.. (ii) Make of DG set be one of the make mentioned in the item. (iii) Spare parts to be replaced shall be suitable for the same make and model of engine as installed at site and serviced. (iv) Cost of lubricating oil shall be measured and paid separately. (v) Cost of Spare parts to be replaced shall be measured and paid separately under item No.110 here in after.

500 KVA 3 phase 50 Hz, Make : Kirloskar

100 KVA to 160 KVA 3 phase 50 HZ, Make : Mahindra/Cuminns/ Kirloskar/ Greaves.

62.5 KVA to 75 KVA 3 phase 50 HZ, Make : Cuminns/ Kirloskar/ Greaves.

20 KVA to 50 KVA 3 phase 50 HZ, Make : Kirloskar

Supply only of the following new parts suitable for DG Set repaired under Schedule `A' item No 109 to 109.05 above :- (Note :- Fixing element of these items is included under the rates quoted by the contractor for respective items of Schedule `A' 109 to 109.05

Water hose pipe set with clamp for 500 KVA capacity of DG set.

Water hose pipe set with clampfor 100 KVA to 160 KVA capacity of DG set.

Water hose pipe set with clamp for 62.5 KVA to 75 KVA capacity of DG set.

Lubricating oil pipe set with coupling for 500 KVA capacity of DG set.

Lubricating oil pipe set with coupling for 100 to 160 KVA capacity of DG set.

Lubricating oil pipe set with coupling for 62.5 KVA to 75 KVAcapacity of DG set.

Fuel pipe set with coupling for 500 KVA capacity of DG set.

Fuel oil pipe set with coupling for 100 KVA to 160 KVA capacity of DG set.

Fuel oil pipe set with coupling for 62.5 KVA to 75 KVA capacity of DG set.

Oil temperature gauge

Water temperature gauge

Oil pressure gauge 0 to 7 kg/cm2

Hours meter

Ampere meter.0-300A

Shut down valve suitable for 62. 5KVA to 500 KVA capacity of DG sets as per existing shape and size.

Disconnecting, and taking out carefully old unserviceable AVR unit and supply , fixing, connecting and testing AVR unit suitable for DG set of 62.5 KVA capacity.and testing for regulated voltage of 415 volts complete all as specified and directed. Make Kirloskar/National/Universal

Supply only lubrication oil SAE-40 (20 W- 40 grade) of Make: IOC/ HINDUSTAN PETROLEUM/ BPCL/ CASTROL) as approved by GE.

Disconnecting and taking out the radiator of following capacity of DG sets and carrying out to work shop, strip opening complete radiator assembly, cleaning of tubes using de-scaling solution, including soldering / gas welding of leakage of tubes. Cutting the rusted portion of in-let or out-let tubes and providing new MS water tubes & jointing with gas welding and assembling the complete radiator including replacement of gasket, nut bolts, and testing for making it leak proof, oiling/servicing of water cooling assembly, replacing unserviceable parts, re-assembling and fixing the same in position and testing the system on actual load. complete all as specified and directed by Engineer-in-Charge.

(a) 160 KVA 3 phase 50Hz, Make : Greaves

(b) 125 KVA to 100 KVA 3 phase 50 HZ, Make : Cuminns/ Kirloskar/ Greaves.

(c) 63 KVA to 50 KVA 3 phase 50 HZ, Make ; Kirloskar

(d) 20 KVA to 35 KVA 3 phase 50 HZ, Make : Kirloskar

NOTES :- (i) Repairs/servicing/reassembling and testing of water cooling assembly shall be carried out on actual load. (ii) The quoted rates of the contractor includes for fixing the serviceable parts in position and replacement of unserviceable parts with new parts. The new replaced parts shall be measured and paid for separately under appropriate item of Sch `A’ as `supply only ‘ but quoted rates are inclusive of replacement of small/minor parts such as nuts, bolts, washers, locking nuts, small springs, screws/gaskets/ packing etc. (iii) The quoted rates of contractor are deemed to be included cost of transportation to and fro upto Work shop/service centre.

Disconnecting and taking out defective battery lead and supplying, fixing, connecting and testing battery lead (Heavy duty) PVC insulated with multi strand copper conductor single core of size 25 Sqmm for 2 metre length including one side fixed with brass/ copper eye hole lugs clamp and other side fixed with brass battery terminal of heavy duty complete all as specified and directed.

Disconnecting and taking down old unserviceable self starter, 12 Volt DC and dismantling complete for repair, servicing, cleaning, varnishing, oiling, reassembling & testing including replacement of the Following parts :- (a) Armature – 01 No (b) Solenoid switch – 01 No. (c) Field coils – 01 No. (d) Commutator – 01 No. (e) Carbon brush – 02 Nos. (f) Bendex assembly – 01 No (g)Tension sleeve=01no (h) Gear assembly-01 no

All as per item No 115.00 here in before but 24 Volt DC

M & L for Cleaning of MS fuel tank of DG sets of various capacity by collecting the fuel in cleaned barrels and removing sludge deposited/ accumulated inside the tank of and disposal of sludge at a distance not exceeding 100 metre and cleaning the tank with kerosene oil, replacement of fuel tank strainer and unserviceable fuel gauge with new PVC fuel level indicator fixed with clips to the tank and marking levels for every 10 litre by marking and numbering on the side of fuel tank with synthetic enameled paint and refilling the collected fuel after filtration complete all as specified and directed.

Dismantling and taking out old unserviceable Dynamo assembly of 62.5 KVA to 250 KVA capacity of DG set for repair and replacement of defective parts like as Carbon brush, Bearing No. 6302 and rewinding to armature with suitable gauge of copper wire, sleeve, glass paper and Varnish, soldering to commutator assembly, reassembling & fixing the same in position and testing the dynamo assembly all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement the following spares/ parts/ components of AMF Panels .

Power Contactor, LCIF 225A,,3 pole, coil voltage 415 / 440 Volts, 50 Hz with 2 NO + 2 NC auxiliary contacts, having current rating (AC3) of 200 Amps at 415 volts as per C & S Electric/GE/BCH.

Power Contactor, 3 pole having current rating (AC3) of 500 Amps at 415 Volts and as per cat part No LC1F 400A of C & S Electric or equivalent of make Siemens / L&T / BCH/GE.

Pla relay 24 Volts DC, 11pin, 2 change over, cat part No. 2C/O – MPC -24D of pla make or equivalent of Eagle man.

Bimetal overload relay type MNX with relay range 24 – 40 Amps suitable for 3 phase 415 volts, AC supply (Make : L&T cat No. SS94145OOFO or equivalent of BCH )

Electronic DC timer suitable for 12/24 Volts DC supply, for 0-60 seconds. (on delay). (Make : L&T / PIC / Aditya Electronic)

Under voltage relay suitable for 3 phase 415 volts, AC supply (Make : PIC / Aditya Electronic )

Engine starting relay with sequence timer & Master timer suitable for 12 / 24 Volts DC supply. (Make : PIC / Aditya Electronic)

Indicating lamps neon type with holder for 12 / 24 volts DC supply (RYB) (Make : L&T/BCH or equivalent make as approved by the GE )

Electronic timer, suitable of 240 / 415 Volts, 50 Hz, AC supply, for 0-180 seconds (ON delay). (Make : L&T / PIC / Aditya Electronic)

S&F in repair MS hinges 100mm size suitable for DG set doors welde or rivetted as required.

S&F in repair unserviceable canopy door lock of suitable size Make : As per sample

Dismantiling existing unserviceable 100 LPD/ 200 LPD solar water heating system and M&L for cleaning & servicing by cleaning complete tubes and internally , de-scaling, cleaning of all effected parts, removing any type of chocking of Solar Collector or tube, repairing any type leakage from Gasket, Rubber Washer after Cold Water inlet and before hot water outlet of Solar Water Heater with cleaning agent and re-fixing in its original position after necessary repairs and replacement of unserviceable spares all as specified and directed. NOTES :- (i) The quoted rates of the contractor includes for fixing the serviceable parts in position and replacement of unserviceable parts with new parts. The new replaced parts shall be measured and paid for separately under appropriate item of Sch `A’ but quoted rates are inclusive of replacement of small/minor parts such as nuts, bolts, washers, locking nuts, small springs, screws/gaskets/ packing etc.

All as per Srl Item No 120.00 above but 300 LPD / 500 LPD

S &F in repair hot water pipe line 20 mm dia (heavy grade) duly insulated with glass wool 50mm and aluminum cladding complete all as specified and directed.

S & F in repair 15 mm dia bore bib taps, chromium plated, screwed down, high pressure capastan head, screwed both ends for iron pipe or for brass ferrule complete all as specifed.

S &F in repair 20 mm dia Gun metal half turn valve/ gate valve with iron wheel head, screwed both ends for GI pipe and fixed complete all as specified and directed.

S & F in repair PVC water storage tank three layer of 500 ltrs capacity, cylindrical, vertical with closed top, hoisted and fixed in position with and including 20 mm bore PTMT ball valve, high pressure with epoxy coated aluminium rod and high density plastic ball, screwed for 20 mm bore iron pipe and connecting to inlet and outlet pipes complete all as specifed and directed.

S & F in replacement heating element of capacity of 3 KW, thread type, suitable for solar water heating system complete all as specified and directed.

S & F in replacement thermostat, capacity 400 W suitable for solar water heating system complete all as specified and directed.

S &F in replacement silicon washer of size 45 mm to 58 mm suitable for solar water heating system complete all as specified and directed.

S&F in replacement sheet metal enclosures 240 volt with 200 Amp bus bar for double door 4 way IP-43 DB's, mounting flush on wall/concealed and making good distubed surfaces complete all as specified and directed by Engr-in-charge.

S &F in replacement Isolator TPN, 32 Amps breaking capacity 10 KA complete all as specified and directed Engr-in-charge.

S & F in replacement Isolator SPN, 40 Amps breaking capacity 10 KA complete all as specifed and directed Engr-in-charge.

S & F in replacement MCB, SP, 'C' series, 6-32 Amps breaking capacity 10 KA complete all as direced Engr-in-charge.

S & F in replacement glass evacuated tube of existng specification(dia 45 to 58 mm approx) for solar water heating system complete all as specified and directed.

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft soil complete all as specified and directed.

M&L for cement concrete 75mm thick type D2 1:4:8 (40 mm graded aggregate) in sub base to floors finished fair and even complete all as specified and directed.

M&L for cement concrete 1:2:4 type B1 (40 mm thick) using 20 mm graded aggregate for flooring finished even & smooth with using extra cement complete all as specifiwed and directed.

M&L for machine pressed rubber moulded precast cement concrete interlocking paver block, prepolished, coloured, any shape and size confirming to IS 15658-2006, of 60mm tickness, M-35 grade, in floors laid dry over and including 25mm thick sand cushion and joints filled with sand all as specified all as directed by Engineer-in-Charge.(Shade and design of tiles shall be approved by GE)

Excavation in post holes (or similar holes) each n.exc 0.5 cum, getting out in soft/loose soil, and removing surplus soil to a distance n.exc 50 m and making good surface complete all as specified.

M&L for structural steel work as in roof trusses (framed), trussed purlins, crane gantries, rails & fastenings & heavy brackets framimg (Pipes, Beam, tee, angle, channel or flat section) including distance pieces, cleats etc. including dismantling of existing frame work complete all as specified and directed. Structural steel conforming to Fe-410W, Grade-E 250, Quality 'A'.

S&F prepainted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strengthn of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including existing AC sheet roofing complete all as specified and directed

M&L for shifting of DG Set 125 KVA from indoor room of Old Bijapur Pump house to Bindal Pump house by disconnecting all electrical connections, exhaust silencer, silent sound proof canopy, blower fans of canopy, foundation bolts or any other work required to shift the DG Set. and reassembling DG Set at new site and connected all electrical connection, any other other disconnected services, canopy etc. Testing of DG Set after assembling complete all as specified and directed. Note : Shifting of DG set should be done through authorised dealer only.

M&L for cement concrete 1:2:4 type B1 using 20 mm graded aggregate for PCC plate form for placing DG Set approx 2 mtr x4 mtr x 600 mm depth (300mm below ground level and 300 mm aobve ground level). finished even & smooth with using extra cement complete all as specified and directed.

M & L cable XLPE insulated screened PVC bedded , galvanized steel strip or wire armoured electric power multi stranded cables 185 Sqmm 3.5 core (heavy duty) 1100 volts laid in trenches passing through pipes /ducts including fixing with necessary lugs at both ends, testing including taking down existing unserviceable cable complete all as specified and directed. Make : Havells/ Polycab/ Grandlay

M&L for Replacement of Speed Control unit ESD (500 KVA) Model : DWC 2000 and Magnetic pick up and connected electrical works complete all as directed

M/s Kamal Traders